A novel control strategy for the partial nitrification and anammox process (PN/A) of immobilized particles: Using salinity as a factor

Influence of aeration modes and DO on simultaneous nitrification and denitrification in treatment of hypersaline high-strength nitrogen wastewater using sequencing batch biofilm reactor (SBBR)

Sequencing batch biofilm reactor (SBBR) has the potential to treat hypersaline high-strength nitrogen wastewater by simultaneous nitrification-denitrification (SND). Dissolved oxygen (DO) and aeration modes are major factors affecting pollutant removal. Low DO (0.35-3.5 mg/L) and alternative anoxic/aerobic (A/O) mode are commonly used for municipal wastewater treatment, however, the appropriate DO concentration and operation mode are still unknown under hypersaline environment because of the restricted oxygen transfer in denser extracellular polymeric substances (EPS) barrier and the decreased carbon source consumption during the anoxic phase. Herein, two SBBRs (R1, fully aerobic mode; R2, A/O mode) were used for the treatment of hypersaline high-strength nitrogen wastewater (200 mg/L NH4+-N, COD/N of 3 and 3% salinity). The results showed that the relatively low DO (2 mg/L) could not realize effective nitrification, while high DO (4.5 mg/L) evidently increased nitrification efficiency by enhancing oxygen transfer in denser biofilm that was stimulated by high salinity. A stable SND was reached 16 days faster with a ∼10% increase of TN removal under A/O mode. Mechanism analysis found that denser biofilm with coccus and bacillus were present in A/O mode instead of filamentous microorganisms, with the secretion of more EPS. Corynebacterium and Halomonas were the dominant genera in both SBBRs, and HN-AD process might assist partial nitrification-denitrification (PND) for highly efficient TN removal in biofilm systems. By using the appropriate operation mode and parameters, the average NH4+-N and TN removal efficiency could respectively reach 100% and 70.8% under the NLR of 0.2 kg N·m-3·d-1 (COD/N of 3), which was the highest among the published works using SND-based SBBRs in treatment of saline high-strength ammonia nitrogen (low COD/N) wastewater. This study provided new insights in biofilm under hypersaline stress and provided a solution for the treatment of hypersaline high-strength nitrogen (low COD/N) water.

Electrospun nanofibers electrostatically adsorb heterotrophic nitrifying and aerobic denitrifying bacteria to degrade nitrogen in wastewater

Nanofibers were prepared by electrospinning a mixture of polycaprolactone and silica, and modified to improve the hydrophilicity and stability of the material and to degrade nitrogenous wastewater by adsorbing heterotrophic nitrifying aerobic denitrifying (Ochrobactrum anthropic). The immobilized bacteria showed highly efficient simultaneous nitrification-denitrification ability, which could convert nearly 90 % of the initial nitrogen into gaseous nitrogen under aerobic conditions, and the average TN removal rate reached 5.59 mg/L/h. The average ammonia oxidation rate of bacteria immobilized by modified nanofibers was 7.36 mg/L/h, compared with 6.3 mg/L/h for free bacteria and only 4.23 mg/L/h for unmodified nanofiber-immobilized bacteria. Kinetic studies showed that modified nanofiber-immobilized bacteria complied with first-order degradation kinetics, and the effects of extreme pH, temperature, and salinity on immobilized bacteria were significantly reduced, while the degradation rate of free bacteria produced larger fluctuations. In addition, the immobilized bacterial nanofibers were reused five times, and the degradation rate remained stable at more than 80 %. At the same time, the degradation rate can still reach 50 % after 6 months of storage at 4 °C. It also demonstrated good nitrogen removal in practical wastewater treatment.

A pilot-scale SNAD-MBBR process for treating anaerobic digester liquor of swine wastewater: performance and microbial community

In this pilot-scale study, simultaneous partial nitrification, anammox, and denitrification (SNAD) process was achieved successfully in a moving bed biofilm reactor (MBBR) for treating anaerobic digester liquor of swine wastewater. After 95 days of operation, when the total nitrogen loading rate of SNAD-MBBR process was 1.09 kg TN/m3/day, the total nitrogen removal rate could reach 0.87 kg TN/m3/day, and the removal efficiencies of ammonium and total nitrogen were 92.0% and 79.7%, respectively. The optimum pH and temperature for SNAD-MBBR process were 8.5 and 35 °C, respectively, and the optimum dissolved oxygen for SNAD1 and SNAD2 were 0.30 and 0.07 mg/L, respectively. The 16S rRNA sequencing suggested that Candidatus Kuenenia, Candidatus Brocadia, Nitrosomonas, and Denitratisoma were the dominant nitrogen removal bacteria. Some of the co-existing bacteria (Truepera, Limnobacter, and Anaerolineaceae uncultured) promoted ammonium oxidation and guaranteed the growth of the anammox bacteria under adverse environmental conditions. Overall, this study demonstrated that the SNAD-MBBR process would be an energy-saving and cost-effective method for the removal of nitrogen from swine wastewater and provided important process parameters for stable operation of the full-scale SNAD process.

A review of microbial nitrogen transformations and microbiome engineering for biological nitrogen removal under salinity stress

The osmotic stress caused by salinity exerts severe inhibition on the process of biological nitrogen removal (BNR), leading to the deterioration of biosystems and the discharge of nitrogen with saline wastewater. Feasible strategies to solve the bottleneck in saline wastewater treatment have attracted great attention, but relevant studies to improve nitrogen transformations and enhance the salt-tolerance of biosystems in terms of microbiome engineering have not been systematically reviewed and discussed. This work attempted to provide a more comprehensive explanation of both BNR and microbiome engineering approaches for saline wastewater treatment. The effect of salinity on conventional BNR pathways, nitrification-denitrification and anammox, was summarized at cellular and metabolic levels, including the nitrogen metabolic pathways, the functional microorganisms, and the inhibition threshold of salinity. Promising nitrogen transformations, such as heterotrophic nitrification-aerobic denitrification, ammonium assimilation and the coupling of conventional pathways, were introduced and compared based on advantages and challenges in detail. Strategies to improve the salt tolerance of biosystems were proposed and evaluated from the perspective of microbiome engineering. Finally, prospects of future investigation and applications on halophilic microbiomes in saline wastewater treatment were discussed.

Effect of phosphorylated polyvinyl alcohol matrix size of cell entrapment on partial nitrification of ammonia in wastewater

Partial nitrification is known as first and critical step for autotrophic nitrogen removal in high strength nitrogenous wastewater. Phosphorylated polyvinyl alcohol gel entrapment was used for suppressing oxygen to nitrite-oxidizing bacteria (NOB) in the gel matrix. The study investigated the effect of the size of gel matrix on partial nitrification. Results show that ammonia-oxidizing bacteria (AOB) proportion in the inoculum rather than the size of gel matrix governed ammonia oxidation. Nitrite oxidation depended on the size of gel matrix not the relative proportions of NOB and AOB in the inoculum. Larger size of gel matrix lead to less in situ oxygen penetration and available for NOB resulting in higher nitrite accumulation. This finding gains a better understanding of using suitable inoculum to control partial nitrification that is beneficial for the preparation of anaerobic ammonium oxidation-suited effluent.

Modified alginate materials for wastewater treatment: Application prospects

Sodium alginate is a natural macromolecule widely used because of its abundance, low cost of acquisition, and rich hydroxyl and carboxyl groups in the matrix. The physical modification of sodium alginate can be made by blending it with polymer materials. The so-yielded alginate complex is commonly unstable in an aqueous environment due to alginate backbones' high hydrophilicity. The chemical modification can remove its hydrophilic groups and introduce special functional groups or polymers onto the alginate backbones to provide excess reaction sites for specific reactions and effective complexation sites for accommodating antibiotics, dyes, heavy metal ions, and radioactive elements. Sodium alginate has been used in water treatment engineering under revised modification protocols. This article also reviews the latest modification protocols for sodium alginate and outlines the novel application of the modified materials. The limitations of modified sodium alginate materials are described, and research prospects are put forward.

Enhanced nitrogen removal from rural domestic sewage via partial nitrification-anammox in integrated vertical subsurface flow constructed wetland

This study aimed to improve the removal of nitrogen treating rural domestic sewage by developing a novel strategy for achieving partial nitrification-anammox (PNA) in an integrated vertical subsurface flow constructed wetland (VSFCW). The influent ammonia was oxidized to nitrite in the partial nitrification VSFCW (VSFCWPN), and 5 mg/L of hydroxylamine was added under the appropriate dissolved oxygen concentration level (1.2 ± 0.2 mg/L) to stabilize the average nitrite accumulation rate at 88.24% and maintain the effluent NO2--N/NH4+-N ratio at 1.26 ± 0.15. The effluent from VSFCWPN was introduced to the following chamber (VSFCWAN), where ammonia and nitrite were removed by the autotrophic anammox process. This implementation achieved high removal efficiencies for chemical oxygen demand, total nitrogen, and PO43--P, reaching 86.26%, 90.22%, and 78.94%, respectively, with influent concentrations of 120.75 mg/L, 60.02 mg/L, and 5.05 mg/L. Substrate samples were collected from 10 cm height (PN1, AN1) and 25 cm height (PN2, AN2). Microbial community analysis showed that Nitrosomonas dominated the community composition in VSFCWPN, with an increase from 1.61% in the inoculated sludgePN to 16.31% (PN1) and 12.09% (PN2). Meanwhile, Ca. Brocadia accounted for 44.81% (AN1) and 36.50% (AN2) in VSFCWAN. These results confirm the feasibility of the proposed strategy for establishing PNA and efficiently treating rural domestic sewage in an integrated VSFCW.

Novel nitrogen removal process in marine aquaculture wastewater treatment using Enteromorpha ferment liquid as carbon

The process performance of partial denitrification of a novel anaerobic fermentation integrated fixed-film activated sludge (IFAS-AFPD) of Enteromorpha was studied. The response surface method was used to determine the optimal reaction conditions, and the operation experiment was carried out under the optimal conditions. The results showed that the nitrogen removal effect was the best when the salinity was 12.2 g•L^-1, the Carbon-Nitrogen ratio (C/N) was 4, the pH was 8.5, and the Nitrite Accumulation Rate, Nitrate Removal Rate, Chemical Oxygen Demand Utilization Rate could reach 77%, 89% and 51%. Experimental results have shown that the NAR of the Enteromorpha ferment liquid system could be maintained at about 74%, which was noteworthy higher than that of the sodium acetate (CH₃COONa) system at 42%; Microbial community analysis showed that Enteromorpha ferment liquid was more beneficial to the growth of Bacteroidetes than CH₃COONa.

Starting-up performances and microbial community shifts in the coupling process (SAPD-A) with sulfide autotrophic partial denitrification (SAPD) and anammox treating nitrate and ammonium contained wastewater

A novel coupling process (SAPD-A) with sulfide autotrophic partial denitrification (SAPD) (NO₃^--N→NO₂^--N) and anaerobic ammonium oxidation (Anammox) was developed using anaerobic sequencing batch reactor (ASBR) in this work. The integrated process comprised two stages. Firstly, the starting-up of SAPD process succeeded by gradually increasing the influent nitrate and sulfide in 95 days. The average nitrate removal efficiency (NRE) and NO₂^--N accumulation rates were 71.24% ± 0.21% and 46.44% ± 0.53% at SAPD process (days 75-95). Then, successful coupling process (SAPD-A) was implemented in two stages (stage I and stage II of SAPD-A). In stage I, it is feasible to promote the successful construction of SAPD-A process by elevating influent ammonium only based on SAPD system, making the NRE increased from 44.45% ± 0.46% (day 95) to 64.62% ± 0.12% at the end of stage I in SAPD-A system (day 126). Meanwhile, the ammonium nitrogen removal efficiency (ARE) and total nitrogen removal efficiency (TN-RE) also rose up to 42.46% ± 2.02% and 63.28% ± 0.54% respectively. Furthermore, the average ARE, NRE and TN-RE during the stage II in the bioreactor could reach 65.17% ± 1.45%, 74.50% ± 0.81% and 77.81% ± 0.37% by loading some biofilters (with of approximate 10% of the volume of the bioreactor) attached anaerobic ammonium oxidation bacteria (AnAOB). High-throughput sequencing results showed that the dominant genera concerning nitrogen removal were norank_f_norank_o_Fimbriimonadates (with the abundance of 2.88-8.54%), norank_ o_ norank _ c_ OM190 (2.48-4.41%), norank_f_norank_o_norank_c_WWE3 (11.01-17.69%), subgroup_10 (1.97-3.81%), Limnobacter（2.17-3.49%）, norank_f_n orank_ o_norank_ c_OLB14 (2.03-5.23%), norank-f-PHOS-HE36 (2.18-5.5%), Ellin6067 (1.34-2.24%) and Candidatus_ Brocadia (1.95-2.42%) during the whole starting-up period of coupling SAPD-A process. Batch experiments revealed that the sulfide was fully oxidized within 2 h, with the maximum reaction rate of 38.30 ± 1.53 mg (L h)^-1 in the first 1 h. Simultaneously, the concentration of nitrate sharply decreased from 53.08 ± 0.23 mg L^-1 to 24.16 ± 0.42 mg L^-1 with the reaction rate of 66.41 ± 2.12 mg (L h)^-1 in 0.5 h. Also, the ammonium concentration significantly declined from 47.88 ± 0.34 mg L^-1 to 10.98 ± 0.39 mg L^-1 in 8 h. Anammox process was responsible for the dominant nitrogen removal in the coupling SAPD-A system.

Applying response surface methodology to optimize partial nitrification in sequence batch reactor treating salinity wastewater

In this study, the operation parameters of a partial nitrification process (PN) treating saline wastewater were optimized using the Box-Behnken design via the response surface methodology (BBD-RSM). A novel strategy based on the control of the carbon/nitrogen ratio (C/N), alkalinity/ammonia ratio (K/A), and salinity in three stages was used to achieve PN in a sequence batch reactor. The results demonstrated that a high and stable PN was completed after 50 d with an ammonia removal efficiency (ARE) of 98.37 % and nitrite accumulation rate (NAR) of 85.93 %. Next, BBD-RSM was applied, where ARE and NAR were the responses. The highest responses from the confirmation experiment were 99.9 % ± 0.04 and 95.25 % ± 0.32 when the optimum C/N, K/A, and salinity were identified as 0.84, 2, and 5.5 (g/L), respectively. The results were higher than those for the nonoptimized reactor. The developed regression model adequately forecasts the PN performance under optimal conditions. Therefore, this study provides a promising strategy for controlling the PN process and shows how the BBD-RSM model can improve the PN performance.

A critical review on microbial ecology in the novel biological nitrogen removal process: Dynamic balance of complex functional microbes for nitrogen removal

The novel biological nitrogen removal process has been extensively studied for its high nitrogen removal efficiency, energy efficiency, and greenness. A successful novel biological nitrogen removal process has a stable microecological equilibrium and benign interactions between the various functional bacteria. However, changes in the external environment can easily disrupt the dynamic balance of the microecology and affect the activity of functional bacteria in the novel biological nitrogen removal process. Therefore, this review focuses on the microecology in existing the novel biological nitrogen removal process, including the growth characteristics of functional microorganisms and their interactions, together with the effects of different influencing factors on the evolution of microbial communities. This provides ideas for achieving a stable dynamic balance of the microecology in a novel biological nitrogen removal process. Furthermore, to investigate deeply the mechanisms of microbial interactions in novel biological nitrogen removal process, this review also focuses on the influence of quorum sensing (QS) systems on nitrogen removal microbes, regulated by which bacteria secrete acyl homoserine lactones (AHLs) as signaling molecules to regulate microbial ecology in the novel biological nitrogen removal process. However, the mechanisms of action of AHLs on the regulation of functional bacteria have not been fully determined and the composition of QS system circuits requires further investigation. Meanwhile, it is necessary to further apply molecular analysis techniques and the theory of systems ecology in the future to enhance the exploration of microbial species and ecological niches, providing a deeper scientific basis for the development of a novel biological nitrogen removal process.

An enriched ammonia-oxidizing microbiota enables high removal efficiency of ammonia in antibiotic production wastewater

High ammonia concentration hinders the efficient treatment of antibiotic production wastewater (APW). Developing effective ammonia oxidation wastewater treatment strategies is an ideal approach for facilitating APW treatment. Compared with traditional nitrification strategies, the partial nitrification process is more eco-friendly, less energy-intensive, and less excess sludge. The primary limiting factor of the partial nitrification process is increasing ammonia-oxidizing bacteria (AOB) while decreasing nitrite-oxidizing bacteria (NOB). In this study, an efficient AOB microbiota (named AF2) was obtained via enrichment of an aerobic activated sludge (AS0) collected from a pharmaceutical wastewater treatment plant. After a 52-day enrichment of AS0 in 250 mL flasks, the microbiota AE1 with 69.18% Nitrosomonas microorganisms was obtained. Subsequent scaled-up cultivation in a 10 L fermenter led to the AF2 microbiota with 59.22% Nitrosomonas. Low concentration of free ammonia (FA, < 42.01 mg L^-1) had a negligible effect on the activity of AF2, and the nitrite-nitrogen accumulation rate (NAR) of AF2 was 98% when FA concentration was 42.01 mg L^-1. The specific ammonia oxidation rates (SAORs) at 30 °C and 15 °C were 3.64 kg NH₄⁺-N·kg MLVSS^-1·d^-1 and 1.43 kg NH₄⁺-N·kg MLVSS^-1·d^-1 (MLVSS: mixed liquor volatile suspended solids). The SAOR was 0.52 kg NH₄⁺-N·kg MLVSS^-1·d^-1 when the NaCl concentration was increased from 0 to 20 g L^-1, showing that AF2 functioning was stable in a high-level salt environment. The ammonia oxidation performance of AF2 was verified by treating abamectin and lincomycin production wastewater. The NARs of AF2 used for abamectin and lincomycin production wastewater treatment were >90% and the SAORs were 2.39 kg NH₄⁺-N·kg MLVSS^-1·d^-1 and 0.54 kg NH₄⁺-N·kg MLVSS^-1·d^-1, respectively, which was higher than the traditional biological denitrification process. In summary, AF2 was effective for APW treatment via enhanced ammonia removal efficiency, demonstrating great potential for future industrial wastewater treatment.

Stable enhanced nitrogen removal from low COD/N municipal wastewater via partial nitrification-anammox in the traditional continuous anoxic/oxic process through bio-augmentation of partial nitrification sludge under decreasing temperatures

The application of partial nitrification-anammox (PNA) in continuous flow processes for treating low COD/N (C/N) sewage remains a critical challenge. Here, a traditional continuous anoxic/oxic (A/O) process was operated to investigate nitrogen removal from municipal wastewater by the bio-augmentation of partial nitrification sludge combined with the inoculation of biocarriers under decreasing temperatures. Stable enhanced nitrogen removal via PNA was achieved. The average total inorganic nitrogen in influent and effluent was 44.3 and 7.1 mg N/L under a low C/N ratio (3.4) and a short hydraulic retention time (8.2 h). The bio-augmentation of partial nitrification sludge enhanced the PNA process under low temperatures (16.9 ± 0.6 °C). The nitrogen removal efficiency remained stable at 83.3 ± 5.7 % as the temperature decreased from 29.1 to 16.3 °C, and the relative abundance of Ca. Brocadia in carrier biofilms increased from 2.22 % to 4.31 % and 3.27 % in two aerobic chambers after 70 days of operation.

Activity enhancement and the anammox mechanism under low temperature via PVA-SA and nano Fe2O3-PVA-SA entrapped beads

Anaerobic ammonia-oxidizing bacteria (AAOB) have a long growth time and low activity at low temperatures. In suspended systems, sludge is easily lost, which limits the mainstream application of anaerobic ammonia oxidation (anammox).Entrapment provides effective ideas for solving these problems. In this study, polyvinyl‑sodium alginate (PVA-SA) and nano Fe₂O₃-PVA-SA entrapment beads were prepared to discuss the effectiveness of entrapment enhanced anammox sludge at low temperatures. The differences in the entrapped beads and granules were compared to analyze the strengthening mechanism. The results show that the nitrogen removal performance of granules, PVA-SA and nano Fe₂O₃-PVA-SA entrapped beads, first decreased and then increased during the cooling and low-temperature operation. Nano Fe₂O₃-PVA-SA entrapped beads showed the smallest decline and the highest degree of recovery. Reaction metering ratio (△NO₂^--N/△NH₄⁺-N and △NO₃^--N/△NH₄⁺-N) showed that entrapment could realize Nitrite oxidizing bacteria (NOB) inhibition and improve the activity of denitrifying bacteria (DNB) to promote the removal of total nitrogen by providing a strict anaerobic environment. The results demonstrate that entrapment is beneficial for maintaining the content of heme c, specifically, nano Fe₂O₃ can stimulate its production, and is beneficial for alleviating the reduction of hydrazine dehydrogenase (HDH) enzyme activity. The extracellular polymeric substances (EPS) content and analysis showed that entrapment does not change the composition of EPS, and can maintain the EPS content. Nano Fe₂O₃ can stimulate AAOB to secrete more EPS to maintain sludge stability. From a molecular perspective, entrapment can maintain the expression of functional genes, promote the enrichment of AAOB, thus improving the nitrogen removal performance from the dual perspectives of "quality" and "quantity".

Anaerobic ammonium oxidation driven by dissimilatory iron reduction in autotrophic Anammox consortia

Feammox has been applied to wastewater biological nitrogen removal. However, few studies have reported that Fe(III)(hydr)oxides induced Anammox consortia to remove NH4+ via the Feammox pathway. In this study, Fe(OH)3 was added to Anammox systems to investigate its effect on nitrogen removal via Feammox. The specific Anammox activity increased by 39 % by Fe(OH)3. Ammonia oxidation was observed to occur along with Fe(III) reduction and Fe(II) generation, which was further confirmed by the isotope test with feeding 15NH4+-N to detect 30N2. The cyclic voltammetry test showed that electron-storage capacity of Anammox sludge increased with Fe(OH)3. In situ Fourier transform infrared spectroscopy suggested that Fe(OH)3 enhanced the polarization of functional groups of outer membrane cytochrome of Anammox consortia to benefit extracellular electron transfer. This study demonstrated that Fe(OH)3 could induce Anammox consortia to perform extracellular respiration to enhance NH4+-N removal in the Anammox sludge system.

A new pattern of the partial nitrification and Anammox immobilized gel beads: core-shell embedded carrier

Single-stage partial nitrification and Anammox (PN/A) is an efficient and energy-saving denitrification process for wastewater. However, its application is limited by the growth conditions of microorganisms. Therefore, we improved the PN/A by developing a novel core-shell embedded carrier. With Anammox gel as the core and Ammonia-oxidizing bacteria gel as the shell, these beads can achieve dissolved oxygen partitioning and provide a suitable environment for the growth of different bacteria. On this basis, the influence of the shape of core-shell embedded gel on nitrogen removal performance was systematically studied, and the internal morphology and pore size of gel beads were characterized. The results showed that the nitrogen removal efficiency of spherical and square gels was increased by 33.70% and 13.47%, respectively, in the batch test. Fluorescence in situ hybridization confirmed the stratified growth of ammonia-oxidizing bacteria and Anammox in carriers, and the relative abundance value of the two bacteria were 1.25:1 and 1.43:1, respectively. Although the mechanical strength of square gel beads is slightly higher than that of spherical, spherical gel is considered the most suitable gel shape due to its small pore size and poor pore connectivity, which ensures the matching of internal Anammox and external PN reaction. In the long-term experiment, the core-shell embedded beads still had the design characteristics, and the TN removal efficiency was increased by 36.25% despite occasional oxygen excess.

Resilience of the wheat root-associated microbiome to the disturbance of phenanthrene

The microbial communities are of high importance to the restoration of ecological function and plant health, while little information about the influence of exogenous pollutants on the resilience and temporal dynamics of root microbial communities is available. In this study, a greenhouse experiment was conducted to investigate the effects of exogenous phenanthrene in terms of time and pollution disturbance on the wheat root-associated microbial communities. It was found that a high phenanthrene degradation rate of 86 % was achieved in the rhizosphere of wheat after the first-week planting. Compared to phenanthrene pollution, temporal changes had more significant impacts on the wheat root microbial communities. Obvious change of microbes influenced by PHE had been revealed at the initial three-week planting even most of PHE has been degraded, and the enriched microbes in the rhizosphere were affiliated to Altererythrobacter, Massilia, Mycobacterium, Ramlibacter, Sphingobium, Novosphingobium and Romboutsia. However, at the later stage after four-week incubation, the wheat root-associated microbial communities gradually recovered to the state without pollution. The results of this study were helpful to deepen the understanding of the response of root-associated microbial resilience to the exogenous phenanthrene pollution, and would benefit the stability and balance of agricultural ecology facing exogenous organic pollutants.

Microbial composition and nitrogen removal pathways in a novel sequencing batch reactor integrated with semi-fixed biofilm carrier: evidence from a pilot study for low- and high-strength sewage treatment

The sequencing batch reactor (SBR) activated sludge process is a well-established technology for sewage treatment. One of the drawbacks of SBRs, however, total nitrogen (TN) removals is insufficient. By means of introducing four improvements, including semi-fixed biofilm carrier, sludge elevation mixing and change for the mode of influent and effluent, compliant standard for TN discharge was obtained in this novel SBR configuration during low- and high-strength sewage load. To illustrate the microbial compositions and functions of the attached biofilm on semi-fixed carrier and the suspended aggregates, as well as the nitrogen removal pathway, high throughput 16S rRNA gene amplicon sequencing, PICRUSt2 algorithm, and KEGG database were applied. The results revealed that (i) the microbial communities from suspended aggregates and biofilm samples were significantly different from each other; (ii) during low-strength sewage loads, TN removal was mainly by nitrification-denitrification. The suspended aggregates was responsible for denitrification, while the biofilm was focused on ammonium oxidation; (iii) during high-strength sewage loads, function of nitrate reductase from suspended aggregates was faded, and anammox and N assimilation by biofilm became dominant. Meanwhile, TN removal referring to the formation of L-glutamine via assimilation was the main pathway.

A review of biomass immobilization in anammox and partial nitrification/anammox systems: Advances, issues, and future perspectives

Two biomass immobilization techniques; entrapment and carrier-based, attract increasing attention in anammox and partial nitrification/anammox (PN/A) systems. This paper provides a comprehensive review of the advances, outstanding issues, and future research directions in this field. The application of both entrapment and carrier-based biofilm immobilization for reactor start up, improving the nitrogen removal performance, and protecting autotrophic bacteria from environmental fluctuations in anammox and partial nitrification/anammox systems are summarized and discussed. The key characteristics of carriers for biomass immobilization are biocompatibility for supporting microbial growth, permeability for effective mass transfer, and physical/chemical stability for long-term use. Carriers without these characteristics must be improved and re-evaluated for their feasibility in applications. Lab-scale, pilot, and full-scale studies are needed to overcome the potential obstacles of preliminary studies, and to investigate the long-term performance of biomass immobilization techniques, especially using real wastewater as influent, which may introduce more complexity and threaten the carrier's immobilization. In addition, calculating the 'nitrogen removal rate normalized by the packing ratio of carriers (NRR-C)' in the immobilization system is strongly suggested to obtain a direct comparison of immobilization performance/limitations from different studies. This review will improve understanding of the major challenges of immobilization technology in anammox and PN/A systems and provide insights into the next-stage of research and full-scale applications.

A Study of a Composite Biofilm Reactor for the Treatment of Mariculture Wastewater: Performance and Microbial Communities

Mariculture wastewater is one of the main sources of saline wastewater. This study used a waterfall aeration biofilm reactor combined with a sequencing batch reactor (WABR-SBR) to treat simulated mariculture sewage. Despite the high inhibition by salinity, the reactor maintained a high removal efficiency for organic matter and ammonium nitrogen. The ammonia nitrogen removal rate was greater than 99%, while that for nitrite, which is extremely toxic to farmed animals, was greater than 80%. Fourier transform infrared spectroscopy and scanning electron microscopy showed that salinity affected the surface structure and composition of biofilms, which became compact and secreted more solute to resist the impact of salinity. High throughput 16S rRNA sequencing revealed that the main phyla in the biofilms were Actinobacteria, Proteobacteria, Firmicutes, and Bacteroidetes. Metagenomic annotation of genes further indicated nitrogen metabolism pathways under high salinity. The conclusions of this study can provide a theoretical foundation for the biological treatment of high-salt wastewater and provide a technical reference for further application of the WABR-SBR composite system.

Combined Phenanthrene and Copper Pollution Imposed a Selective Pressure on the Rice Root-Associated Microbiome

Combined organic and inorganic pollutants can greatly impact crops and microbes, but the interaction between coexisted pollutants and their effects on root-associated microbes under flooding conditions remains poorly understood. In this study, greenhouse experiments were conducted to investigate the individual and combined effects of phenanthrene (PHE) and copper (Cu) on rice uptake and root-associated microbial coping strategies. The results showed that more than 90% of phenanthrene was degraded, while the existence of Cu significantly reduced the dissipation of PHE in the rhizosphere, and the coexistence of phenanthrene and copper promoted their respective accumulation in plant roots. Copper played a dominant role in the interaction between these two chemicals. Microbes that can tolerate heavy metals and degrade PAHs, e.g., Herbaspirillum, Sphingobacteriales, and Saccharimonadales, were enriched in the contaminated soils. Additionally, microbes associated with redox processes reacted differently under polluted treatments. Fe reducers increased in Cu-treated soils, while sulfate reducers and methanogens were considerably inhibited under polluted treatments. In total, our results uncover the combined effect of heavy metals and polycyclic aromatic hydrocarbons on the assemblage of root-associated microbial communities in anaerobic environments and provide useful information for the selection of effective root-associated microbiomes to improve the resistance of common crops in contaminated sites.

Ammonium-assimilating microbiome: A halophilic biosystem rationally optimized by carbon to nitrogen ratios with stable nitrogen conversion and microbial structure

The contradiction between theoretical metabolism of ammonium assimilation and experiential understanding of conventional biosystems makes the rational optimization of the ammonium-assimilating microbiome through carbon to nitrogen (C/N) ratios perplexing. The effect of different C/N ratios on ammonium-assimilating biosystems was investigated in saline wastewater treatment. C/N ratios significantly hindered the nutrient removal efficiency, but ammonium-assimilating biosystems maintained functional stability in nitrogen conversions and microbial communities. With sufficient biomass, higher than 86% ammonium and 73% phosphorus were removed when C/N ratios were higher than 25. Ammonium assimilation dominated the nitrogen metabolism in all biosystems even under relatively low C/N ratios, evidenced by the extremely low abundances of nitrification functional genes. Different C/N ratios did not significantly change the bacterial community structure of ammonium-assimilating biosystems. It is anticipated that the ammonium-assimilating biosystem with advantages of clear metabolic pathway and easy optimization can be applied to nutrient removal and recovery in saline environments.

Enhanced treatment of organic matters in starch wastewater through Bacillus subtilis strain with polyethylene glycol-modified polyvinyl alcohol/sodium alginate hydrogel microspheres

Starch wastewater is a wide range of environmental issues with organic pollutants. A high efficiency and stability hydrogel-organic degradation system was designed via Bacillus Subtilis with Polyethylene glycol (PEG)-modified Polyvinyl alcohol (PVA)/Sodium alginate (SA) hydrogel microspheres. Bacillus subtilis was immobilized on the surface or inside of PEG-modified PVA/SA hydrogels microspheres via physical adsorption. Results showed PEG-modified PVA/SA microspheres had an effect of adsorption on Bacillus subtilis with enhancing bearing rate to 54.22% compared to the blank control group. The effect of microspheres on degradation was remarkable in simulation starch wastewater with a maximum COD removal rate of 93.35% and compared in reality starch wastewater with 90.02% under the optimal condition of pH = 6, 35℃, 20% dosage, 180 rpm. This novel biological method on starch wastewater enhanced tolerance of microorganisms and degradation effect, reflecting safety, effectiveness, and economy with great significance to environmental protection.

Start-up of mainstream anammox process through inoculating nitrification sludge and anammox biofilm: Shift in nitrogen transformation and microorganisms

The feasibility of starting up mainstream single-stage partial nitrification-anammox (SPNA) system by inoculating nitrification sludge and anammox biofilm was investigated. The SPNA system treating low-strength synthetic wastewater was rapidly started up with TN removal efficiency of 88.5 ± 1.8% and effluent nitrate concentration of 7.2 ± 1.2 mg/L. Both the abundance and maximum activity of nitrite oxidizing bacteria (NOB) in flocs decreased obviously. Interestingly, the abundance of anaerobic ammonium oxidizing bacteria (AnAOB) in flocs increased from 0.213% to 0.346% despite the sludge retention time (SRT) of flocs decreased to 60 days, the AnAOB in biofilm was 0.434%. That meant AnAOB gradually enriched in flocs and accounted for a fairly high proportion. The inhibition of NOB, partial denitrification and increased aerobic_chemoheterotrophy function in flocs might be the main reasons for AnAOB enrichment. The possibility of simultaneous fermentation, partial denitrification and anammox reaction was predicted in biofilm, further improving the stability of the system.

Culturing partial denitrification biofilm in side stream incubator with ordinary activated sludge as inoculum: One step closer to mainstream Anammox upgrade

Recently, adding carriers into anoxic zone is proposed for mainstream Anammox upgrade, which relied on the denitrifiers responsible for partial denitrification (PD) to generate essential nitrite for Anammox bacteria. Still, their low abundance in the naturally formed biofilm leads to insufficient nitrite supply. This study investigated the sequential culturing of PD biofilm. By inoculating ordinary activated sludge, the PD process was quickly established within 54-day. During that, decreasing carbon to nitrogen ratio and anoxic duration in order might be effective strategies. Adding carriers shifted the microbial community, especially the proliferation of Flavobacterium. When solely using the mature PD biofilm, high nitrate to nitrite transformation ratio (>70%) was obtained. Meanwhile, both nitrate-reducing and nitrite-generating processes slowed down and lasted ∼90 min. In addition, abundant Simplicispira candidate for PD was detected in biofilm. This study also suggests that regularly harvesting PD-related functional bacteria from a side-stream incubator promotes mainstream Anammox upgrade.

Advanced nitrogen removal from landfill leachate via a two-stage combined process of partial nitrification-Anammox (PNA) and partial denitrification-Anammox (PDA)

In this study, a two-stage combined process of partial nitrification-Anammox (PNA) and partial denitrification-Anammox (PDA) was established achieving advanced nitrogen removal from landfill leachate. The PNA sludge used to treat reject water adapted to the leachate in 37 days, resulting in fast start-up of the PNA process with a nitrogen removal rate (NRR) of 0.22 kgN/(m³·d). Partial denitrification (PD) was induced using sodium acetate and proceeded in a stepwise manner using sludge fermentation liquid (SFL), achieving a NO₃^--N to NO₂^--N transformation ratio (NTR) of 52.1 ± 1.1% within 16 days. PDA was established via the addition of mature Anammox biofilms. The nitrogen removal efficiency (NRE) of this system was 97.6 ± 1.5%, of which PNA and PDA contributed 74.8 ± 4.0% and 18.7 ± 4.1%, respectively. Nitrosomonas (2.6% in PNA), Thauera (16.0% in PDA) and Candidatus Brocadia (23.0% in PNA, 1.4% in PDA) were dominant in the two-stage system. This study provides valuable and novel insights, supporting the practical application of PNA-PDA processes in landfill sites.

A novel stable nitritation process: Treating sludge by alternating free nitrous acid/heat shock

The feasibility of stable nitritation of sludge alternately treated by free nitrous acid (FNA) and heat shock in a sequencing batch reactor (SBR) was investigated in this study. The linear regression method was used to determine the optimal treatment conditions. Results revealed that an FNA concentration of 2.20 mg HNO₂-N/L, exposure time of 24 h, and treatment ratio of 20% could inhibit nitrite oxidizing bacteria (NOB) activity to the greatest extent while maintaining the maximum ammonium oxidizing bacteria (AOB) activity; after heat shock at 60 °C for 20 min, NOB were inhibited while AOB still had certain activity. In the long-term continuous-flow experiment, the single FNA or heat shock treatments easily allowed adapt NOB to affect the stability of nitritation. The alternating FNA/heat shock treatment can achieve long-term stability of nitritation. Microbial community analysis revealed that the alternating FNA/heat shock treatment could inhibit NOB while maintaining high AOB abundance.

Performances and mechanisms of microbial nitrate removal coupling sediment-based biochar and nanoscale zero-valent iron

Immobilized microorganism technology has attracted increasing attention for high concentration of microbes, low cell loss and high resistance to impact of environment. The microbial reduction of nitrate in the presence of sediment-based biochar (SBC) and nanoscale zero-valent iron (nZVI) was investigated in four different free systems. NZVI-SBC/bacteria system realized the best nitrate removal of 97.61% within 3 days through the synergistic effect of SBC and nZVI on denitrifying bacteria. Accumulation of nitrite and ammonium in nZVI-SBC/bacteria system also decreased. High-throughput sequencing results showed that the proportion of denitrifying bacteria in microbial community structure increased after adding nZVI-SBC. The performance of nitrate removal was then studied through PVA/SA-immobilization. Immobilized active pellets performed better nitrate removal (98.89%) and stronger tolerance under different conditions than the free bacterial cells. Overall, this study provided a promising approach by utilizing SBC and nZVI for the bio-remediation of nitrate-contaminated water in practical application.

A novel process of salt tolerance partial denitrification and anammox (ST-PDA) for treating saline wastewater

In the study, the salt-tolerant partial denitrification and Anammox (ST-PDA) process was established, meanwhile, the feasibility of salinity inhibition model as the boundary control method and the subsequent operation performance were studied. Study indicated that the performance of salt-tolerant PD sludge was the optimum under the 10 g·L^-1 salinity, and AnAOB also maintained high activity at the salinity. Haldane and Aiba models verified that NO₃^--N (substrate) and FNA (product) would have negative consequences for performance of ST-PDA system. However, the effect of FNA would be eliminated by self-alkalization in the denitrification process. A 90% nitrogen removal rate was achieved and the average effluent total nitrogen of 17.8 mg·L^-1 was maintained in the system. The high throughput sequencing revealed that the species richness decreased with the salinity increased, while Thauera played a major role in nitrogen removal in saline environment. The study provides a novel insights for salt-containing industrial wastewater.

Effect of low salinity on nitrogen removal from municipal wastewater via a double-anammox process coupled with nitritation and denitratation: Performance and microbial structure

Saline wastewater present in municipal pipe networks poses challenges to biological nitrogen removal due to its inhibition on microorganisms. This study focuses on the effects of low salinity (0.0%, 0.4%, 0.7% and 1.0%) on a system featuring a combination of nitritation/anammox in oxic stage and denitratation/anammox in anoxic stage (double-anammox) in a step-feed SBR for municipal wastewater over a period of 130 days. The results showed that a maximum nitrogen removal efficiency of 81.2% was achieved at a salinity of 1.0% with anammox contribution of 76.5%. Analysis of anammox contribution and sludge activities discovered that low salinity promoted both nitritation and denitratation, further enhancing the coupling with anammox. Further, microbial analysis confirmed that Ca. Brocadia was enriched on biofilms from 0.21% to 0.51% and Nitrosomonas was enriched in flocs from 0.50% to 1.04%. Overall, the double-anammox process appears to be a promising method for the treatment of saline wastewater.

Advanced nitrogen elimination from domestic sewage through two stage partial nitrification and denitrification (PND) coupled with simultaneous anaerobic ammonia oxidation and denitrification (SAD)

The start-up, efficient, and secure operation of Anammox treating low ammonia sewage, is an important research focus. In this study, a partial nitrification-denitrification coupled with simultaneous Anammox and denitrification (PND-SAD) process was achieved in sequencing batch reactor/up-flow anaerobic sludge bed (SBR-UASB). The key measures to maintain high efficiency PND were: (i) controlling dissolved oxygen in the SBR below 0.5 mg/L, which is not only conducive to PN, but also promotes the contribution of simultaneous nitrification and denitrification to nitrogen removal; (ii) monitoring the nitrate (NO₃^--N) of SBR effluent and discharging sludge to wash out nitrate oxidation bacteria when the NO₃^--N exceeds 1.0 mg/L. The nitrite accumulation rate reached 97.6%. SBR effluent and domestic sewage entered the UASB. Although Candidatus Brocadia only accounted for 0.8%, its contribution to nitrogen removal reached 76.8%. In PND-SAD system, the aerobic HRT was only 3.8 h, nitrogen removal efficiency up to 97.3%.

Enhancing the treatment performance of partial denitrification/Anammox process at high nitrogen load: Effects of immobilized strain HFQ8C/Non the sludge characteristics

A novel strategy based on quorum sense (QS) was proposed to improve the treatment performance of the partial denitrification/Anammox (PD/A) process at high loads by adding immobilized Pseudomonas sp. HFQ8_C/N, which could release high concentrations of N-butyryl-DL-homoserine lactone (C4-HSL), N-octanoyl-DL- homoserine lactone (C8-HSL) and N-decanoyl-DL-homoserine lactone (C10-HSL). The results showed that adding immobilized HFQ8_C/N improved the sludge activity and settleability, contributing to higher nitrogen removal efficiency at the high nitrogen loading rate (NLR). It was proved that C4-HSL promoted the abundances of Thauera and Candidatus Kuenenia at NLR 1.68-2.52 kg N/(m³·d), while C10-HSL promoted the abundance of Candidatus Brocadia. Besides, C8-HSL and C10-HSL played different regulation roles in the production of protein (PN) in tightly bound extracellular polymeric substances (TB-EPS) at different loads, improving the sludge settleability. This study provided a new way to improve the treatment performance of high-load PD/A processes.

Adaptation and evolution of freshwater Anammox communities treating saline/brackish wastewater

The most common way to apply Anammox for saline wastewater treatment is via salt adaptation of freshwater Anammox bacteria (FAB). To better apply this process in practice, it's essential to understand the salt adaptation process of FBA, as well as the underlying mechanisms. This study investigated the long-term salt adaptation process of a fixed-film FAB culture in three reactors (namely R1-R3), under salinities of 2, 8, and 12 NaCl g/L, correspondingly. All three reactors were under stable operation and achieved 80-90% total inorganic nitrogen removal efficiency throughout the 425-day operation period. R1 servers as a blank control, based on the clear microbial community shifts in R2 and R3, the operation period was divided into 2 phases. During Phase 1, all FAB in the three reactors belonged to Ca. Brocadia sp.. The Anammox activity (AA) and the ratio of nitrite/ammonium (NO₂^--N/NH₄⁺-N) consumption in R2 and R3 decreased with the increase of salinity and did not recover to the initial levels. During Phase 2, the relative abundance of Ca. Kuenenia sp. in R2 and R3 increased from nearly 0 to about 60 and 77%, respectively. With the growth of Ca. Kuenenia sp., the AA and stoichiometry of R2 and R3 gradually recovered. AA of R2 and R3 both reached 1.0 g NH₄⁺-N/L/day at the end of this phase, which was about 80% of that in R1. These results indicated that the salt adaptation of FAB culture was achieved by species shift from a low salt-tolerance one to a high salt-tolerance one.

Recovery of phosphorus from eutrophic water using nano zero-valent iron-modified biochar and its utilization

Effective removal and recovery of phosphorus (P) from the aquatic environment was of great significance for eutrophication control and P recovery. This study investigated the effects of different environmental conditions on P adsorption by biochar (BC) and the feasibility of applying the P-laden BC as a fertilizer for plant growth. The nano zero-valent iron (nZVI) modified reeds BC prepared at 700 °C (Fe-700-BC) had the maximum P adsorption capacity of 95.2 mg g^-1, which was higher than those prepared at 300, 500, and 900 °C. The addition of Fe-700-BC reduced the concentration of total phosphorus (TP) in the overlying water, in which the soluble reactive phosphorus (SRP) almost completely removed, as well as had a certain inhibitory effect on the growth of algae. Simultaneously, Fe-700-BC reduced the contents of different fractions of P (weakly adsorbed inorganic phosphorus (WA-Pi), potential active inorganic phosphorus (PA-Pi), and Fe/Al-bound inorganic phosphorus (Fe/Al-Pi)) by adsorbing the soluble P released from the sediments, especially in the case of disturbance. Fe-700-BC had no significant effect on the diversity and richness of the microbial community in the sediment. Moreover, P-laden BC was safe and environmentally friendly for application in the soil and tended to increase stem and root length, fresh and dry weight at low doses (0.5 wt%) in wheat planting experiments. The present work could provide a reference for solving the problems related to eutrophication and P deficiency.

Effects of interactions between quorum sensing and quorum quenching on microbial aggregation characteristics in wastewater treatment: A review

Due to the increasingly urgent demand for effective wastewater denitrification and dephosphorization systems, there is a need to improve the performance of existing biological treatment technologies. As a bacteria-level communication mechanism, quorum sensing (QS) synchronizes gene expression in a density-dependent manner and regulates bacterial physiological behavior. On this basis, the QS-based bacterial communication mechanism and environmental factors affecting QS are discussed. This paper reviews the influence of QS on sludge granulation, biofilm formation, emerging contaminants (ECs) removal, and horizontal gene transfer in sewage treatment system. Furthermore, the QS inhibition strategies are compared. Based on the coexistence and balance of QQ and QS in the long-term operation system, QQ, as an effective tool to regulate the growth density of microorganisms, provides a promising exogenous regulation strategy for residual sludge reduction and biofilm pollution control. This paper reviews the potential of improving wastewater treatment efficiency based on QS theory and points out the feasibility and prospect of exogenous regulation strategy. PRACTITIONER POINTS: The mechanism of bacterial communication based on QS and the environmental factors affecting QS were discussed. The application of QS and QQ in improving the sludge performance of biological treatment systems was described. The significance of QS and QQ coexistence in sewage treatment process was described.

Improving denitrification efficiency in constructed wetlands integrated with immobilized bacteria under high saline conditions

Constructed wetlands (CWs) inoculated with exogenous microbes have great potential for removing pollutants in adverse environments. The rapid loss of functional bacteria and the high cost of repeated additions of inoculum, however, limit the practical application of this technology. In this study, C-F2 immobilized bacteria (i.e., immobilized salt-tolerant bacterium Alishewanella sp. F2 incorporated with a carbon source) were developed and utilized in CWs for solving the above problems. A 60-day experiment demonstrated that bioaugmented CWs (Bio-CWs) with the addition of C-F2 immobilized bacteria into the bottom gravel layer of CW microcosms (B-CF2 treatment) exhibited high nitrogen removal efficiency under a saline condition (electrical conductivity of 15 mS/cm). We measured mean nitrate nitrogen (NO₃^--N) and total nitrogen (TN) removal percentages of 97.8% and 88.1%, respectively, which were significantly (p < 0.05) higher than those in Bio-CWs with microbial inoculum (MI-F2 treatment, 63.5% and 78.2%) and unbioaugmented CWs (CK, 48.7% and 67.2%). The TN content of the entire plant was significantly (p < 0.05) increased in B-CF2 (636.06 mg/microcosm) compared with CK (372.06 mg/microcosm). The relative abundances of the genera Alishewanella (i.e., the exogenous bacterium, 5.5%), Clostridium-XlVa (8.8%) and Bacteroides (21.1%) in B-CF2 were significantly (p < 0.05) higher than in MI-F2 and CK, which improved the denitrification capacity of CWs. Overall, a high denitrification efficiency and durability were achieved in the newly developed Bio-CWs (i.e., B-CF2 treatment) with immobilized bacteria under saline conditions, which provides an alternative technology for the rapid removal of nitrogen from saline wastewater.

Performance and responses of aerobic granular sludge at different concentrations of graphene oxide after a single administered dose

To investigate the impact of graphene oxide (GO) under different concentrations (0, 50, 100, 150, and 200 mg/L) on aerobic granular sludge (AGS) after a single administered dose, the performance of nitrogen removal, microbial enzymatic activity, extracellular polymeric substances (EPSs), and microbial community structure was analyzed in batch tests. The results showed that the impact of GO concentrations on AGS was dose- and time-dependent. Short-term GO exposure could accelerate the nitrification process of AGS, while relatively concentrations (≥100 mg/L) inhibited the process when present for extended periods of time. The microbial enzymatic activity showed similar tendency. The production of lactate dehydrogenase release (LDH) in 200 mg/L group was increased 48.04% and EPS contents decreased 30.06% compared to the control group at 30th day and showed that high concentrations of GO have toxic effects on AGS. The microbial bacteria responded differently to the stimulation of different concentrations of GO. PRACTITIONER POINTS: GO affected AGS system performance in concentration- and time-dependent manners. The nitrification rate of AGS increased in the short term and reversed over time. Long-term exposure to high GO concentrations caused toxicity to AGS. Different microorganisms had diverse responses to GO concentrations.

One-step start-up and subsequent operation of CANON process in a fixed-bed reactor by inoculating mixture of partial nitrification and Anammox sludge

The feasibility of one-step start-up of CANON process in a FBR by inoculating mixture of partial nitrification and Anammox sludge as well as its subsequent operation performances were investigated in the present study. The FBR was operated for around 3 months. The CANON process was quickly started up within 21 days. The max total nitrogen (TN) removal rate reached 183.61 g m^-3 d^-1 with the TN removal efficiency of 91.81% on day 95. The CANON process exhibited a good capability for resistance to loading shock and restoration from the unstable state. The mature CANON biofilms displayed a morphology of aggregates and had porous and microporous structure. The structural characteristics of the biofilms were conducive to improve the transferring of substrates and products. AOB and Anammox bacteria absolutely predominated in the mature biofilms and furthermore established a balanced interaction relationship. The microbial community structure contributed to the relatively stable operation performances.

Research progress on enhancing the performance of autotrophic nitrogen removal systems using microbial immobilization technology

The autotrophic nitrogen removal process has great potential to be applied to the biological removal of nitrogen from wastewater, but its application is hindered by its unstable operation under adverse environmental conditions, such as those presented by low temperatures, high organic matter concentrations, or the presence of toxic substances. Granules and microbial entrapment technology can effectively retain and enrich microbial assemblages in reactors to improve operating efficiency and reactor stability. The carriers can also protect the reactor's internal microorganisms from interference from the external environment. This article critically reviews the existing literature on autotrophic nitrogen removal systems using immobilization technology. We focus our discussion on the natural aggregation process (granulation) and entrapment technology. The selection of carrier materials and entrapment methods are identified and described in detail and the mechanisms through which entrapment technology protects microorganisms are analyzed. This review will provide a better understanding of the mechanisms through which immobilization operates and the prospects for immobilization technology to be applied in autotrophic nitrogen removal systems.

Coupling anammox with denitrification in a full-scale combined biological nitrogen removal process for swine wastewater treatment

In order to enhance nitrogen removal through anammox process in the full-scale swine wastewater treatment plant, an innovative regulation strategy of nitrate-based carbon dosage and intermittent aeration was developed to apply the combined biological nitrogen removal process in a full scale anaerobic-anoxic-oxic (A²/O) system. TN removal efficiency reached at 65.5 ± 6.0% in Phase 1 with decreasing external carbon dosage in influent due to the reduction of return nitrate concentration, and it increased to 83.5 ± 6.7% when intermittent aeration was adopted in oxic zone and external carbon source was stopped adding into influent in Phase 2. As a result, the energy consumption for the swine wastewater treatment decreased from 1.93 to 0.9 kW h/m³ and 4.18 to 2.57 kW h/kg N, respectively. Microbial community analysis revealed that the average abundances of Candidatus Brocadia increased from 0.76% to 2.43% and removal of TN through anammox increased from 39% to 77%.

A new method for in-situ treatment of waste gas scrubbing liquid containing both NH3 and H2S based on sulfur autotrophic denitrification and partial nitrification-Anammox coupling system

In this study, an integrated device with scrubbing and biochemical treatment functions was used, and partial nitrification (PN)-Anammox and sulfur autotrophic denitrification (SADN) processes were coupled in a biochemical treatment pond to explore the feasibility of in-situ autotrophic removal of NH₃ and H₂S. The results showed that the removal efficiency of NH₃ and H₂S in waste gas are 95% and 87.5% respectively. The scrubbing liquid was efficiently treated in the biochemical treatment pond. Nitrogenous compounds weren't accumulated in liquid and converted to N₂ by SADN and PN-Anammox coupling system. S^2- was mainly used by SADN process to reduce NO₃^-. The scrubbing liquid processed by the biochemical treatment pond was refluxed to the scrubber to achieve continuous absorption of NH₃ and H₂S. Microbial community and functional microbial analysis showed that the PN-Anammox and SADN processes were the main processes to achieve the conversion of pollutants in the scrubbing liquid.

A review of quorum sensing improving partial nitritation-anammox process: Functions, mechanisms and prospects

Partial nitritation-anammox (PNA) is a promising and energy-efficient process for the sustainable nitrogen removal. However, its wide applications are still limited by the long start-up period and instability of long-term operation. Quorum sensing (QS), as a way of cell-to-cell communication generally regulating various microbial behaviors, has been increasingly investigated in PNA process, because QS may substantially manipulate the metabolism of microorganisms and overcome the limitations of PNA process. This critical review provides a comprehensive analysis of QS in PNA systems, and identifies the challenges and opportunities for the optimization of PNA process based on QS. The analysis is grouped based on the configurations of PNA process, including partial nitritation, anammox and single-stage PNA systems. QS is confirmed to regulate various properties of PNA systems, including microbial activity, microbial growth rate, microbial aggregation, microbial interactions and the robustness under adverse conditions. Major challenges in the mechanisms of QS, such as QS circuits, target genes and the response to environmental inputs, are identified. Potential applications of QS, such as short-term addition of certain acyl-homoserine lactones (AHLs) or substances containing AHLs, transient unfavorable conditions to stimulate the secretion of AHLs, are also proposed. This review focuses on the theoretical and practical cognation for QS in PNA systems, and serves as a stepping stone for further QS-based strategies to enhance nitrogen removal through PNA process.

Partial nitrification performance and microbial community evolution in the membrane bioreactor for saline stream treatment

Effects of salinity level and gradient on partial nitrification performance, sludge properties and microbial activities were investigated using partial nitrification membrane bioreactors (PN-MBRs). PN-MBRs obtained stable nitrite accumulation rate of 91.1% and ammonia removal of 64.8% at 10 g/L NaCl. 10 g/L NaCl obtained higher oxygen uptake rate than 5 g/L, and promoted the differentiation of ammonium-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria. Salinity increased sludge flocs size, stimulated secretion of extracellular polymeric substances with high carbohydrates contents, but had insignificant impact on sludge settleability and dewaterability. Salt level and gradient were both important for microbial community evolution to salt-tolerant bacteria. PN-MBRs enriched aerobic AOBs (Nitrosomonas and norank_f_Nitrosomonadaceae) and anaerobic AOBs (Candidatus_Kuenenia and Candidatus_Brocadia) for partial nitrification, while salt gradients resulted in different metabolism pathways for nitrification even at the same salinity. Increasing salinity promoted hydroxylamine oxidizer in nitrification process evolving from Candidatus_Kuenenia and Candidatus_Brocadia to aerobic AOBs.

Mainstream nitrogen separation and side-stream removal to reduce discharge and footprint of wastewater treatment plants

The activated sludge process is efficient for pollutant removal, but was criticized for its large upfront investment and land area requirements. Improving nitrogen removal to levels sufficient to reduce eutrophication is a challenge to conventional nitrification and denitrification, which is limited by process configuration (with nitrate recirculation) and environmental inhibition. To satisfy stringent discharge standards within a compact plant footprint, a sustainable strategy by moving nitrogen removal from mainstream to side-stream is designed by a cycle of ammonium exchange, regeneration and nitrogen removal (AERN), combined with biological and physiochemical technologies. Ammonium was rapidly captured by ion exchangers, then exchanged into regenerant, and converted to N₂ by chlorination or Sharon-anaerobic ammonia oxidation in the side-stream. The AERN cycle can be combined with a high-rate anaerobic/aerobic process and chemical phosphorus removal to construct a HAERN process, or inserted between a coagulation-sedimentation tank and a membrane bioreactor to construct a CAERNM process. Two AERN-based systems both achieved efficient pollutants removal (especially for nitrogen removal of 86.8-93.7%) in long-term running, and didn't impair exchange capacity and properties of ion exchangers. Compared with the conventional anaerobic/anoxic/aerobic process, AERN-based processes reduce land occupancy, upfront investments, and treatment costs by 59.9-71.1%, 25.5-38.0% and 2.3-31.0%, respectively.

Divergent Microbiota Dynamics along the Coastal Marine Ecosystem of Puerto Rico

Understanding the different factors shaping the spatial and temporal distribution of marine microorganisms is fundamental in predicting their responses to future environmental disturbances. There has been, however, little effort to characterize the microbial diversity including the microbiome dynamics among regions in the Caribbean Sea. Toward this end, this study was designed to gain some critical insights into microbial diversity within the coastal marine ecosystem off the coast of Puerto Rico. Using Illumina MiSeq, the V4 region of the 16S rRNA gene was sequenced with the goal of characterizing the microbial diversity representative of different coastal sites around the island of Puerto Rico. This study provided valuable insights in terms of the local bacterial taxonomic abundance, α and β diversity, and the environmental factors shaping microbial community composition and structure. The most dominant phyla across all 11 sampling sites were the Proteobacteria, Bacteroidetes, and Planctomycetes, while the least dominant taxonomic groups were the NKB19, Tenericutes, OP3, Lentisphaerae, and SAR406. The geographical area (Caribbean and Atlantic seas) and salinity gradients were the main drivers shaping the marine microbial community around the island. Despite stable physical and chemical features of the different sites, a highly dynamic microbiome was observed. This highlights Caribbean waters as one of the richest marine sources for a microbial biodiversity hotspot. The data presented here provide a basis for further temporal evaluations aiming at deciphering microbial taxonomic diversity around the island, while determining how microbes adapt to changes in the climate.

Sources, Influencing Factors, and Pollution Process of Inorganic Nitrogen in Shallow Groundwater of a Typical Agricultural Area in Northeast China

As one of the largest agricultural areas, the Sanjiang Plain of Northeast China has faced serious inorganic nitrogen pollution of groundwater, but the sources and the formation mechanism of pollution in the regional shallow groundwater remain unclear, which constrains the progress of pollution control and agricultural development planning. An investigation on potential nitrogen sources, groundwater inorganic nitrogen compounds (NH4+, NO3−, NO2−), and topsoil total nitrogen concentration (TN) was conducted in a typical paddy irrigation area of Sanjiang Plain. Multivariate statistical analysis combined with geospatial-based assessment was applied to identify the sources, determine the governing influencing factors, and analyze the formation process of inorganic nitrogen compounds in shallow groundwater. The results show that the land use type, oxidation-reduction potential (Eh), groundwater depth, NO2− concentration, and electrical conductivity (EC) are highly correlated with the NO3− pollution in groundwater, while DO and Eh affected the distribution of NH4+ most; the high concentrations of NO3− in sampling wells are most likely to be found in the residential land and are distributed mainly in densely populated areas, whereas the NH4+ compounds are most likely to accumulate in the paddy field or the lands surrounded by paddy field and reach the highest level in the northwest of the area, where the fields were cultivated intensively with higher fertilization rates and highest values of topsoil TN. From the results, it can be concluded that that the NO3− compounds in groundwater originated from manure and domestic waste and accumulated in the oxidizing environment, while the NH4+ compounds were derived from N fertilization and remained steady in the reducing environment. NO2− compounds in groundwater were the immediate products of nitrification as a result of microorganism activities.

Gel immobilization: A strategy to improve the performance of anaerobic ammonium oxidation (anammox) bacteria for nitrogen-rich wastewater treatment

Anaerobic ammonium oxidation (anammox) process appears a suitable substitute to nitrification-denitrification at a lower C/N ratios. Anammox is a chemolithoautotrophic process, belong to phylum Planctomycetes, and they are slow growing bacteria. Different strategies, e.g., biofilm formation, granulation and gel immobilization, have been applied to maintain a critical mass of bacterial cells in the system by avoiding washout from the bioreactor. Gel immobilization of anammox appears the best alternative to the natural process of biofilm formation and granulation. Polyvinyl alcohol-sodium alginate, polyethylene glycol, and waterborne polyurethane are the most reported materials used for the entrapment of anammox bacteria. However, dissolution of the gel beads refrains its application for long term bioprocess. Magnetic powder could coat on the surface of the beads which may increase the mechanical strength and durability of pellets. Application and problem of immobilization technology for the commercialization of this technology also addressed.

Optimization of nitrogen and carbon removal with simultaneous partial nitrification, anammox and denitrification in membrane bioreactor

In this study, a membrane bioreactor (MBR) was used to achieve both nitrogen and carbon removal by a simultaneous partial nitrification, anammox and denitrification (SNAD) process. During the entire experiment, the intermittent aeration (non-aerobic time : aeration time, min min^-1) cycle was controlled by a time-controlled switch, and the aeration rate was controlled by a gas flowmeter, and the optimal operating parameters as determined by response surface methodology (RSM) were a C/N value of 1.16, a DO value of 0.84 mg l^-1 and an aerobic time (T _ae) of 15.75 min. Under these conditions, the SNAD process achieved efficient and stable nitrogen and carbon removal; the total inorganic nitrogen removal efficiency and chemical oxygen demand removal efficiency were 92.31% and 95.67%, respectively. With the formation of granular sludge, the membrane fouling rate decreased significantly from 35.0 Pa h^-1 at SNAD start-up to 19.9 Pa h^-1 during stable operation. Fluorescence in situ hybrid analyses confirmed the structural characteristics and the relative ratio of aerobic ammonia-oxidizing bacteria, anaerobic ammonia-oxidizing bacteria and denitrifying bacteria in the SNAD system.

Performance and microbial structure of partial denitrification in response to salt stress: Achieving stable nitrite accumulation with municipal wastewater

The effects of inorganic salts on partial denitrification (PD) was investigated in a sequencing batch reactor for simultaneously treating saline nitrate sewage and municipal wastewater. After 230-day operation, a high nitrate-to-nitrite transformation ratio (NTR) of ~ 80% was achieved with the salinity of 1.25 wt% and the initial chemical oxygen demand to nitrate ratio of 3.7. Microbial community analysis revealed that, Thauera was remained predominant in PD system but with a relative abundance decreasing from 53.02% (0.0 wt%) to 42.36% (1.25 wt%). Moreover, as a suitable ratio of nitrite to ammonia (~1.6) in effluent was obtained, it would be a promising method to treat saline nitrate sewage by combing PD with anammox.