Low-cost biochar adsorbents prepared from date and delonix regia seeds for heavy metal sorption

Boosting acetaminophen degradation in water by peracetic acid activation: A novel approach using chestnut shell-derived biochar at varied pyrolysis temperatures

In this study, biochar derived from chestnut shells was synthesized through pyrolysis at varying temperatures from 300 °C to 900 °C. The study unveiled that the pyrolysis temperature is pivotal in defining the physical and chemical attributes of biochar, notably its adsorption capabilities and its role in activating peracetic acid (PAA) for the efficient removal of acetaminophen (APAP) from aquatic environments. Notably, the biochar processed at 900 °C, referred to as CN900, demonstrated an exceptional adsorption efficiency of 55.8 mg g-1, significantly outperforming its counterparts produced at lower temperatures (CN300, CN500, and CN700). This enhanced performance of CN900 is attributed to its increased surface area, improved micro-porosity, and a greater abundance of oxygen-containing functional groups, which are a consequence of the elevated pyrolysis temperature. These oxygen-rich functional groups, such as carbonyls, play a crucial role in facilitating the decomposition of the O-O bond in PAA, leading to the generation of reactive oxygen species (ROS) through electron transfer mechanisms. This investigation contributes to the development of sustainable and cost-effective materials for water purification, underscoring the potential of chestnut shell-derived biochar as an efficient adsorbent and catalyst for PAA activation, thereby offering a viable solution for environmental cleanup efforts.

Pinecone biochar for the Adsorption of chromium (VI) from wastewater: Kinetics, thermodynamics, and adsorbent regeneration

High concentration of chromium in aquatic environments is the trigger for researchers to remediate it from wastewater environments. However, conventional water treatment methods have not been satisfactory in removing chromium from water and wastewater over the last decade. Similarly, many adsorption studies have been focused on one aspect of the treatment, but this study dealt with all aspects of adsorption packages to come up with a concrete conclusion. Therefore, this study aimed to prepare pinecone biochar (PBC) via pyrolysis and apply it for Cr(VI) removal from wastewater. The PBC was characterized using FTIR, SEM-EDX, BET surface area, pHpzc, Raman analyses, TGA, and XRD techniques. Chromium adsorption was studied under the influence of PBC dose, solution pH, initial Cr(VI) concentration, and contact time. The characteristics of PBC are illustrated by FTIR spectroscopic functional groups, XRD non-crystallite structure, SEM rough surface morphology, and high BET surface area125 m2/g, pore volume, 0.07 cm3/g, and pore size 1.4 nm. On the other hand, the maximum Cr (VI) adsorption of 69% was found at the experimental condition of pH 2, adsorbent dosage 0.25 mg/50 mL, initial Cr concentration 100 mg/L, and contact time of 120 min. Similarly, the experimental data were well-fitted with the Langmuir adsorption isotherm at R2 0.96 and the pseudo-second-order kinetics model at R2 0.99. This implies the adsorption process is mainly attributed to monolayer orientation between the adsorbent and adsorbate. In the thermodynamics study of adsorption, ΔG was found to be negative implying the adsorption process was feasible and spontaneous whereas the positive values of ΔH and ΔS indicated the adsorption process was endothermic and increasing the degree of randomness, respectively. Finally, adsorbent regeneration and reusability were successful up to three cycles. In conclusion, biochar surface modification and reusability improvements are urgently required before being applied at the pilot scale.

Strength and functionalized borage biochar for effective elimination of nickel contamination: Insight into batch and dynamic flow mode treatment applications

A silica gel-modified borage biochar (BB@Si) was first produced and used as a binding agent for potentially hazardous Ni2+ ions in aqueous systems. The recommended biochar was more effective in eliminating Ni2+ than pristine biochar (BB). Its maximum qm could reach up to 1.39 × 10-3 mol/g at 30 °C, and sorption isotherms showed that the Langmuir model could more accurately define its sorption behavior. The Dubinin-Radushkevich isotherm also revealed that the average sorption energy ranged from 11.00 to 11.14 kJ/mol. Zeta potential tests, SEM images, and FT-IR scans confirmed the interactions between BB@Si and Ni2+ ions. Dynamic flow treatment studies showed high uptake effectiveness when the flow rate and amount of BB@Si were suitable. Nickel desorption yield of around 80% from BB@Si was noted with 0.01 M HCl. The BB@Si column's breakthrough and exhausted points were identified to be 45 and 352 min, respectively. Its maximum exhaustion capacity value was determined to be 52.73 mg/g. Ni2+ removal from the actual wastewater sample exceeded 75%. The resulting outcomes imply the immense potential of employing BB@Si in the treatment of Ni2+- contaminated aqueous systems.

Immature persimmon residue as a novel biosorbent for efficient removal of Pb(II) and Cr(VI) from wastewater: Performance and mechanisms

Owing to the powerful affinity of tannin toward heavy metal ions, it is frequently immobilized on adsorbents to enhance their adsorption properties. However, natural adsorbents containing tannin have been overlooked owing to its water solubility. Herein, a novel natural adsorbent based on the immature persimmon residue (IPR) with soluble tannin removed was fabricated to eliminate Pb(II) and Cr(VI) in aquatic environments. The insoluble tannin in IPR endowed it with prosperous properties for eliminating Pb(II) and Cr(VI), and the IPR achieved maximum Pb(II) and Cr(VI) adsorption quantities of 68.79 mg/g and 139.40 mg/g, respectively. Kinetics and isothermal adsorption analysis demonstrated that the removal behavior was controlled by monolayer chemical adsorption. Moreover, the IPR exhibited satisfactory Pb(II) and Cr(VI) removal efficiencies even in the presence of multiple coexisting ions and showed promising regeneration potential after undergoing five consecutive cycles. Additionally, Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) analysis unveiled that the elimination mechanisms were primarily electrostatic attraction, chelation and reduction. Overall, the IPR, as a tannin-containing biosorbent, was verified to possess substantial potential for heavy metal removal, which can provide new insights into the development of novel natural adsorbents from the perspective of waste resource utilization.

Valorization of non-edible fruit seeds into valuable products: A sustainable approach towards circular bioeconomy

Global imperatives have recently shown a paradigm shift in the prevailing resource utilization model from a linear approach to a circular bioeconomy. The primary goal of the circular bioeconomy model is to minimize waste by effective re-usage of organic waste and efficient nutrient recycling. In essence, circular bioeconomy integrates the fundamental concept of circular economy, which strives to offer sustainable goods and services by leveraging biological resources and processes. Notably, the circular bioeconomy differs from conventional waste recycling by prioritizing the safeguarding and restoration of production ecosystems, focusing on harnessing renewable biological resources and their associated waste streams to produce value-added products like food, animal feed, and bioenergy. Amidst these sustainability efforts, fruit seeds are getting considerable attention, which were previously overlooked and commonly discarded but were known to comprise diverse chemicals with significant industrial applications, not limited to cosmetics and pharmaceutical industries. While, polyphenols in these seeds offer extensive health benefits, the inadequate conversion of fruit waste into valuable products poses substantial environmental challenges and resource wastage. This review aims to comprehend the known information about the application of non-edible fruit seeds for synthesising metallic nanoparticles, carbon dots, biochar, biosorbent, and biodiesel. Further, this review sheds light on the potential use of these seeds as functional foods and feed ingredients; it also comprehends the safety aspects associated with their utilization. Overall, this review aims to provide a roadmap for harnessing the potential of non-edible fruit seeds by adhering to the principles of a sustainable circular bioeconomy.

Tetraethylenepentamine-Grafted Amino Terephthalic Acid-Modified Activated Carbon as a Novel Adsorbent for Efficient Removal of Toxic Pb(II) from Water

In this study, a new composite, tetraethylenepentamine (TEPA), was incorporated into amino terephthalic acid-modified activated carbon (ATA@AC) through a one-pot integration of TEPA with the COOH moiety of ATA@AC. This process resulted in the creation of a TEPA@ATA@AC composite for Pb(II) removal from an aquatic environment. Several techniques, including SEM, EDX, FT-IR, TGA, XRD, and Zeta potential, were employed to emphasize the chemical composition, morphology, and thermal durability of the as-synthesized TEPA@ATA@AC composite. The impact of experimental variables on the adsorption of Pb(II) ions was studied using batch adsorption. The uptake assessment suggested that the TEPA@ATA@AC composite exhibited superior Pb(II) removal performance with high removal efficiency (97.65%) at pH = 6.5, dosage = 0.02 g, equilibrium time = 300 min, and temperature = 298 K. The isotherm data exhibited good conformity with the Langmuir isotherm model, whereas the kinetics data displayed strong agreement with both pseudo-first-order and pseudo-second-order kinetics models. This reflected that the Pb((II) uptake by the TEPA@ATA@AC composite was caused by physisorption coupled with limited chemisorption. The greatest monolayer uptake capacity of the TEPA@ATA@AC composite was 432.8 mg/g. The thermodynamic findings indicated that the Pb(II) uptake on the TEPA@ATA@AC composite was an exothermic and feasible process. After five adsorption-desorption runs, the TEPA@ATA@AC composite maintained a superior uptake capacity (83.80%). In summary, the TEPA@ATA@AC composite shows promise as a potent adsorbent for effectively removing Cr(VI) from contaminated water, with impressive removal efficiency.

Technoeconomic and carbon footprint analysis of simulated industrial scale biodiesel production process from mixed macroalgal and non-edible seed oil using sulphonated zinc doped recyclable biochar catalyst

The present research explored the sustainable production of biodiesel from mixed oils of marine macroalgae and non-edible seeds using a sulphonated Zinc doped recyclable biochar catalyst derived from coconut husk. The maximum biodiesel conversion of 94.8 % was yielded with optimized conditions of 10:1 methanol to oil molar ratio, 4.8 % biochar catalyst concentration, 54.5 ℃ temperature and 87.4 min reaction time. A techno-economic assessment provided a favourable return on investment (ROI) of 21.59 % and 4.63 years of reimbursement period, with a calculated minimum selling price of 0.81 $/kg of produced biodiesel. The carbon footprint analysis results estimated an annual emission of 752.07 t CO2 which corresponds to 0.088 kg CO2 emission per kg of biodiesel produced from the simulated process. The study on economic viability and environmental consciousness of biodiesel production not only paves the way for a greener and sustainable future while also contributing to low carbon footprint.

Parameter Influence, Characterization and Adsorption Mechanism Studies of Alkaline-Hydrolyzed Garcinia kola Hull Particles for Cr(VI) Sequestration

Despite the regulations by The World Health Organization (WHO) on the permissible limit of chromium, many industries still discharge wastewater polluted with chromium into the environment irrationally. This poses a lot of risk to aquatic lives and humans because of its carcinogenic and toxic attributes. Thus, treatment of industrial wastewater polluted with chromium is highly imperative before its disposal. Nonetheless, the hulls generated from Garcinia kola in our various farmlands also causes environmental pollution when dumped unknowingly. In this present study, Garcinia kola hull particles (GK-HP) was hydrolyzed using NaOH and applied as adsorbent for Cr(VI) sequestration. The raw Garcinia kola hull particles (rGK-HP) and modified Garcinia kola hull particles (cMGK-HP) were characterized using Brunauer-Emmett-Teller (BET) method, scanning electron microscopy (SEM), powder X-ray diffractometry (XRD), Fourier-Transform-Infrared (FTIR), thermogravimetric analysis (TGA), energy dispersive spectroscopy (EDS) and point of zero charge (pHpzc). The influence of pH, adsorbent dose, contact time, temperature and adsorbate initial concentration on Cr(VI) sequestration were examined. The cMGK-HP was able to remove 96.25% of Cr(VI) from solution and proved to be effective than rGK-HP. The amount of Cr(VI) removed from solution decreased as the pH and adsorbate initial concentration were increased. However, the amount increased as the adsorbent dose, contact time and temperature were increased. Change in morphological structure, textural property, spectral peak, phase composition and adsorbents chemical composition before and after Cr(VI) sequestration from solution were proved by SEM, BET, FTIR, XRD, and EDS analyses respectively. The isotherm and kinetic studies suggest Cr(VI) adsorption on adsorbents' surface to be monolayer in nature and adsorption data to be well-fitted into pseudo second order model respectively. The cMGK-HP possessed excellent reusability attribute and high thermal stability as shown by TGA. In conclusion, cMGK-HP could effectively be used as an adsorbent for Cr(VI) sequestration from solution.

Eco-friendly nano-enabled fertilizers derived from date industry waste for sustainable and controlled-release of P, K and Mg nutrients: sorption mechanisms, controlled-release performance and kinetics

Development of nano-enabled fertilizers from green waste is one of the effective options to enhance global agricultural productions and minimize environmental pollution. In this study, novel, eco-friendly and cost-effective nano- enabled fertilizers (NEF) were synthesized using the planetary ball milling procedure. The NEF (nDPF1and nDPF2) were prepared by impregnation of nanostructured date palm pits (nDPP) with (KH2PO4 + MgO) at 1:1 and 3:1 (w/w) ratios respectively. The nDPP, nDPF1 and nDPF2 were extensively characterized. The produced nano-fertilizers enhanced soil water retention capacity with nDPF2 being the most effective. The water retention capacity of nDPF2 treated soil was 5.6 times higher than that of soil treated with conventional fertilizers. In addition, the nDPF2 exhibited superior sustained lower release rates of P, K and Mg nutrients for longer release periods in comparison with the conventional fertilizers. For instance, P cumulative release percentages from conventional fertilizers, nDPF1 and nDPF2 in soil reached 22.41%, 10.82 and 8.9% respectively within 384 h. Findings from FTIR and XPS analyses suggested that hydrogen bonding and ligand exchange were the main interaction mechanisms of PO4-K-Mg ions with nDPP surface. The released kinetics data of the NEF revealed that power function was the best suitable model to describe the kinetics of P, K and Mg release data from NEF in water and soil. Pot study ascertained that the nano-enabled fertilizers (nDPF1 and nDPF2) significantly promoted biomass production and nutrient uptake of maize plants as compared to commercial fertilizer treated plants. The present work demonstrated the potential of NEF to increase nutrients uptake efficiency, mitigate moisture retention problem in arid soils and reduce nutrients loss through leaching and safeguard the environment.

Kinetics and modeling of Pb (II) adsorption in pellet biochar based on micro-computed tomography characterization

Biochar, a cost-effective adsorbent for the removal of heavy metals from aqueous solutions, has gained increasing attention. In this study, an advanced micro-computed tomography (micro-CT) system was used to investigate the adsorption kinetics by direct localization and visualization of Pb (II) on wheat straw pellet biochar. The normalized digital images indicating the dynamic changes of Pb (II) adsorption on biochar samples at different initial Pb (II) concentrations of 100, 200, 300, and 400 mg/L and adsorption times were obtained. It was found that image grayscale (GS) changes over adsorption time (t) followed the power function, GSe/GSt=2.45∗t-0.27. Based on this finding, modified pseudo-first-order (PFO) and pseudo-second-order (PSO) models incorporated with time-dependent kinetic constants kPFOt=KPFO∗GSe/GSt and kPSOt=KPSO∗GSe/GSt were proposed, resulting in a better interpretation of the adsorption mechanism. The micro-CT-guided novel approach demonstrated visual evidence-based superiority and should prove valuable to the existing body of research in related fields.

Co-exposure of microplastics and heavy metals in the marine environment and remediation techniques: a comprehensive review

Microplastics (MPs) and heavy metals are significant pollutants in the marine environment, necessitating effective remediation strategies to prevent their release into the sea through sewage and industrial effluent. This comprehensive review explores the current understanding of the co-exposure of MPs and heavy metal-enriched MPs, highlighting the need for effective remediation methods. Various mechanisms, including surface ion complexation, hydrogen bonding, and electrostatic forces, contribute to the adsorption of heavy metals onto MPs, with factors like surface area and environmental exposure duration playing crucial roles. Additionally, biofilm formation on MPs alters their chemical properties, influencing metal adsorption behaviors. Different thermodynamic models are used to explain the adsorption mechanisms of heavy metals on MPs. The adsorption process is influenced by various factors, including the morphological characteristics of MPs, their adsorption capacity, and environmental conditions. Additionally, the desorption of heavy metals from MPs has implications for their bioavailability and poses risks to marine organisms, emphasizing the importance of source reduction and remedial measures. Hybrid approaches that combine both conventional and modern technologies show promise for the efficient removal of MPs and heavy metals from marine environments. This review identifies critical gaps in existing research that should be addressed in future studies including standardized sampling methods to ensure accurate data, further investigation into the specific interactions between MPs and metals, and the development of hybrid technologies at an industrial scale. Overall, this review sheds light on the adsorption and desorption mechanisms of heavy metal-enriched MPs, underscoring the necessity of implementing effective remediation strategies.

Taguchi Parametric Optimization and Cost Analysis of Hexavalent Chromium Sequestration From Aqueous Solution by NaOH-Modified Garcinia kola Hull Particles

The presence of chromium in industrial wastewater is unavoidable due to its large usage as part of chemical constituents used in many industries. Its removal from wastewater is imperative because it's toxic in nature. This study investigated the application of NaOH-modified Garcinia kola hull particles (cMGK-HP) for Cr(VI) sequestration from aqueous solution. The optimization of process parameters was executed using Taguchi of Design Expert software for optimum point prediction, analysis of variance, parameters interaction and mathematical model development. A proposed model was used for the adsorption cost analysis. The predicted and experimental percentage of Cr(VI) sequestration were recorded at optimum point to be 99.02% and 98.76% with pH, adsorbent dose, contact time, initial concentration, and temperature of 2, 8 g/L, 20 minutes, 10 mg/L, and 20°C respectively. A correlation coefficient of .9937 between experimental and predicted values of percentage Cr(VI) sequestration affirmed high efficacy of the developed model. ANOVA showed the order of parameter contribution to be pH > adsorbent dose > initial concentration > contact time > temperature. A maximum adsorption capacity of 217.39 mg g-1 was obtained for cMGK-HP. Cost analysis revealed using cMGK-HP to be cost effective for Cr(VI) sequestration with a total operational cost of 0.824 $/mole Cr(VI) ions when compared with commercial activated carbon. Adsorbent characterization revealed the presence of active functional groups enhancing the sequestration process. It could be deduced that cMGK-HP is effective to remove Cr(VI) from solution.

Efficient Cr(VI) sequestration from aqueous solution by chemically modified Garcinia kola hull particles: characterization, isotherm, kinetic, and thermodynamic studies

There is a need for the removal of hexavalent chromium from contaminated water prior to its discharge into the environment, as part of industrial effluents, due to its toxic nature. In this present study, an adsorbent prepared via chemical modification of Garcinia kola hull particles (GK-HP) using NaOH was applied for Cr(VI) sequestration from aqueous solution. Both the raw (rGK-HP) and chemically modified Garcinia kola hull particles (cMGK-HP) were characterized using BET, SEM, XRD, FTIR, TGA, and EDS. The effects of pH, contact time, adsorbent dose, adsorbate initial concentration, and temperature on Cr(VI) sequestration were examined. The adsorbent, cMGK-HP, proved to be more effective for the adsorption process than rGK-HP with 96.25% removal efficiency at a pH of 2, a contact time of 60 min, an adsorbent dose of 5 g/L, Cr(VI) initial concentration of 20 mg/L and a temperature of 40°C. Isotherm and kinetic studies showed experimental data to be well-fitted with Langmuir isotherm and follow the pseudo-second-order kinetic model. The thermodynamic study revealed adsorption nature to be feasible, occur via physisorption, spontaneous, and exothermic. Changes in morphological structure, textural property, spectral peak, phase composition, and chemical composition of adsorbents before and after Cr(VI) sequestration from solution were proved by SEM, BET, FTIR, XRD, and EDS analyses, respectively. cMGK-HP possessed excellent reusability attribute and high thermal stability as shown by TGA. In conclusion, the adsorption capacity of cMGK-HP is better than many other adsorbents generated from agrowastes used in previous studies for Cr(VI) removal.

Enhanced removal performance of magnesium-modified biochar for cadmium in wastewaters: Role of active functional groups, processes, and mechanisms

In this study, a series of biochar products with different active functional groups were developed by one-pot coprecipitation method, including magnesium-modified biochar (MgBC) and functional group-grafted MgBC (Cys@MgBC, Try@MgBC, and Glu@MgBC), for effective adsorption of cadmium (Cd(II)) from wastewaters. These biochars exhibited excellent removal performance for Cd(II), particularly Cys@MgBC, whose maximum Cd(II) adsorption capacity reached 223.7 mg g-1. The highly active and weakly crystalline Mg could adsorb Cd(II) through precipitation and ion exchange, which was further promoted by the introduced functional groups through complexation and precipitation. After 120 d of natural process, the immobilization efficiency of Cd(II) by Cys@MgBC, Try@MgBC, and Glu@MgBC was still maintained at 98.7%, 95.2%, and 82.7% respectively. This study proposes and clarifies the complexation mechanism of functional group-grafted Mg-modified biochar for heavy metals, providing new insights into the practical application of these biochars.

Efficient Removal of Hexavalent Chromium (Cr(VI)) from Wastewater Using Amide-Modified Biochar

The utilization of biochar, derived from agricultural waste, has garnered attention as a valuable material for enhancing soil properties and serving as a substitute adsorbent for the elimination of hazardous heavy metals and organic contaminants from wastewater. In the present investigation, amide-modified biochar was synthesized via low-temperature pyrolysis of rice husk and was harnessed for the removal of Cr(VI) from wastewater. The resultant biochar was treated with 1-[3-(trimethoxysilyl) propyl] urea to incorporate an amide group. The amide-modified biochar was characterized by employing Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) techniques. During batch experiments, the effect of various parameters, such as adsorbent dosage, metal concentration, time duration, and pH, on Cr(VI) removal was investigated. The optimal conditions for achieving maximum adsorption of Cr(VI) were observed at a pH 2, an adsorbent time of 60 min, an adsorbent dosage of 2 g/L, and a metal concentration of 100 mg/L. The percent removal efficiency of 97% was recorded for the removal of Cr(VI) under optimal conditions using amide-modified biochar. Freundlich, Langmuir, and Temkin isotherm models were utilized to calculate the adsorption data and determine the optimal fitting model. It was found that the adsorption data fitted well with the Langmuir isotherm model. A kinetics study revealed that the Cr(VI) adsorption onto ABC followed a pseudo-second-order kinetic model. The findings of this study indicate that amide-functionalized biochar has the potential to serve as an economically viable substitute adsorbent for the efficient removal of Cr(VI) from wastewater.

Competitive adsorption and immobilization of Cd, Ni, and Cu by biochar in unsaturated soils under single-, binary-, and ternary-metal systems

This study investigated the competitive adsorption and immobilization of cadmium (Cd), nickel (Ni), and copper (Cu) by biochar in unsaturated soils under single-, binary-, and ternary-metal systems. The results showed that the immobilization effects by the soil itself were in the order of Cu > Ni > Cd, and the adsorption capacities of freshly contaminated heavy metals by biochar were in the order of Cd > Ni > Cu in unsaturated soils. The adsorption and immobilization of Cd by biochars in soils was weakened by competition more in the ternary-metal system than that in the binary-metal system; the competition with Cu caused a more significant weakening effect than that with Ni. For Cd and Ni, nonmineral mechanisms preferentially adsorbed and immobilized Cd and Ni compared to mineral mechanisms, but the contributions of the mineral mechanisms to the adsorption gradually increased and became dominant with increasing concentrations (at average percentages of 62.59%-83.30% and 41.38%-74.29%, respectively). However, for Cu, the contributions of the nonmineral mechanisms to Cu adsorption were always dominant (average percentages of 60.92%-74.87%) and gradually increased with increasing concentrations. This study highlighted that the types of heavy metals and coexistence should be focused when remediating heavy metal contamination in soils.

Tracing the synergistic migration of biochar and heavy metals based on 13C isotope signature technique: Effect of ionic strength and flow rate

Understanding the transport of biochar and heavy metals is important for evaluation of the long-term stability and ecotoxicity of heavy metals after biochar remediation. In this study, ¹³C-labelled biochar was prepared to investigate the synergistic down migration of biochar and heavy metals in the soil profile, and the effect of ionic strength (IS) and flow rate was examined. Results showed that the ¹³C-labelled biochar with high δ¹³C (249.3 ‰) was suitable for tracing the migration of biochar without influencing its adsorption for heavy metals (i.e., Cu²⁺ and Cd²⁺). Both higher IS and flow rate were favorable for the release of biochar, but higher IS inhibited the transport of biochar in soil profile, which was attributed to the enhanced primary- and secondary-minimum deposition based on the Derjaguin-Landau-Verwey-Overbeek (DLVO) analysis. The transport of Cu²⁺ and Cd²⁺ was facilitated by high IS and flow rate. The release of Cd from biochar was mainly affected by IS, due to ion exchange and a weaker electrostatic attraction to biochar at higher IS, while that of Cu was mainly affected by flow rate related to co-migration of metal with biochar. Metal-biochar particle was the dominant form to migrate in upper soil layer, whereas, soluble Cd²⁺ and Cu²⁺ desorbed from biochar were the dominant forms that migrated to the deeper soil. The synergistic down migration of biochar and heavy metals might pose less risks than the sole migration of soluble metals. That is, high IS might cause higher risks than high flow rate even though biochar and metals might transport further with high flow rate. These findings will advance the current knowledge on the migration risk involved in the in-situ remediation of heavy metal-contaminated soils by biochar.

Coassisted carbonization with HCOOK/(HCOO)2Ca for the fabrication of bamboo-derived oxygen-doped porous carbons exhibiting high-performance sorption of diethyl phthalate from aqueous solutions

Porous carbons are excellent sorbents for removing organic pollutants. Green conversion of biowaste into advanced porous carbons is crucial for industrialized production and practical applications, which, however, have rarely been investigated. This study develops a coassisted carbonization method for the preparation of porous carbons with the environmentally friendly agents HCOOK and (HCOO)₂Ca for the first time. The bamboo waste-derived hydrochar was transformed into oxygen-doped porous carbons, which displayed a large surface area and pore volume, abundant oxygen content, graphene structure and many surface functional groups. These properties contributed to the extremely high sorption of large quantities of diethyl phthalate, which reached 761 mg g^-1. Surface adsorption, including pore filling, hydrogen bonding, and π-π stacking, rather than partitioning, was the main sorption process. Therefore, this study provides a sustainable and promising route for the preparation of porous carbons that can be applied in the efficient removal of organic pollutants.

Simultaneous removal of heavy metals and dye from wastewater: modelling and experimental study

In this work, heavy metals were removed simultaneously using wheat bran as an adsorbent. For batch experiments, the Box-Behnken design of response surface methodology was used and the effect of dye on metal removal was analysed. It has been observed that the presence of dye has reduced the removal of each metal in the range of 100-20% with no appreciable reduction in dye adsorption. The optimum pH, temperature, and adsorbent dose were found to be 7.59, 33.23 °C, and 2.90 g/L, respectively, for 79.70% chromium, 99.9% cadmium and 87.27% copper removal. It was found that Langmuir isotherm fits well with the experimental data (RMSE value up to 0.033). The maximum adsorption capacity obtained for copper, chromium, cadmium and dye were 2.17 mg/g, 1.76 mg/g, 1.52 mg/g and 3.215 mg/g, respectively. The continuous study was performed for parameters, i.e. bed height (0.15-0.45 m), flow rate (5-15 mL/min) and initial metal concentration (100-500 mg/L). In continuous study, dye acted as an interfering species and as a result breakthrough and exhaustion time decreased. The modelling and simulation of continuous adsorption process were performed. A dynamic mathematical model was developed for continuous fixed bed adsorption column to compare the breakthrough curve with experimental results.

Potentially toxic elements (PTEs) in Gomti-Ganga Alluvial Plain, associated human health risks assessment and potential remediation using novel-nanomaterials

The health risks associated with consumption of water from river Gomti polluted with potentially toxic elements (PTEs), including As, Fe, Pb, Cd, Mn, Cr, Ni, and Hg were investigated at the initiation of unlocking of COVID-19 lockdown and compared with pre-COVID-19 lockdown status. In the current investigation, the total hazard index (THI) values exceeded the acceptable limit of "unity" at all sampling stations. The use of river water for drinking and domestic purposes by millions of people with high THI values has emerged as a matter of huge concern. The individual hazard quotients associated with Cd and Pb were found to be most severe (> 1). A vivid difference between the THI values during the two study phases indicated the positive impact of COVID-19 lockdown signifying the prominent impact of anthropogenic activities on the PTE concentrations. The closure of local manufacturing units (textile, battery, etc.) emerged as a potential reason for decreased health risks associated with PTE levels. The higher susceptibility of children to health risks in comparison with adults through the values of THI and HQs was interpreted across the study area. Potential remedial measures for PTE contamination have also been suggested in the study.

Carbon-based adsorbents as proficient tools for the removal of heavy metals from aqueous solution: A state of art-review emphasizing recent progress and prospects

Carbon-centric adsorbents (CCA) are diverse forms, from simple biochar (BC) to graphene derivatives, carbon nanotubes (CNTs), and activated carbon (AC), which have been vastly explored for their removal of a plethora of pollutants, including heavy metals (HM). The prominent features of CCA are their operational attributes like extensive surface area, the occurrence of flexible surface functional groups, etc. This work offers a comprehensive examination of contemporary research on CCA for their superior metal removal aptitude and performances in simulated solutions and wastewater flows; via portraying the recent research advances as an outlook on the appliances of CACs for heavy metal adsorption for removal via distinct forms like AC, BC, Graphene oxide (GO), and CNTs. The bibliometric analysis tool was employed to highlight the number of documents, country-wise contribution, and co-occurrence mapping based on the Scopus database. The coverage of research works in this review is limited to the last 5 years (2017-2021) to highlight recent progress and prospects in using CCAs such as AC, BC, GO, and CNTs to remove HM from aqueous media, which makes the review unique. Besides an overview of the common mechanisms of CACs, the future scope of CAC, especially towards HM mitigation, is also discussed in this review. This review endorses that further efforts should be commenced to enhance the repertory of CCAs that effectively eliminate multiple targeted metals in both simulated and real wastewater.

Immobilization on anionic metal(loid)s in soil by biochar: A meta-analysis assisted by machine learning

Metal pollution in soil has become one of the most serious environmental problems in China. Biochar is one of the most widely used remediation agents for soil metal pollution. However, the literature does not provide a consistent picture of the performance of biochar on the immobilization of anionic metal(loid)s, especially arsenic, in soil. To obtain a baseline understanding on the interactions of metals and biochar, 597 data records on four metal(loid)s (As, Cr, Sb and V) were collected from 70 publications for this meta-analysis, and the results are highlighted below. Biochar has a significant immobilization effect on anionic metal(loid)s in soil and reduces the bioavailability of these metals to plants. Subgroup analysis found that biochar could decrease the potential mobility of Cr, Sb and V, but the immobilization effect on As was not always consistent. Meanwhile, biochar pH and soil pH are the most key factors affecting the immobilization effect. To summarize, biochar can effectively immobilize Cr, Sb and V in soil, but more attention should be given to As immobilization in future applications. By regulating the properties of biochar and appropriate modification, anionic metal(loid)s in soil can be immobilized more effectively. Hence, both of the soil quality and crop quality can be improved.

Exploring agricultural waste biomass for energy, food and feed production and pollution mitigation: A review

Globally agricultural production system generates a huge amount of solid waste. Improper agri-waste management causes environmental pollution which resulted in economic losses and human health-related problems. Hence, there is an urgent need to design and develop eco-friendly, cost-effective, and socially acceptable agri-waste management technologies. Agri-waste has high energy conversion efficiency as compared to fossil fuel-based energy generation materials. Agri-waste can potentially be exploited for the production of second-generation biofuels. However, composted agri-waste can be an alternative to energy-intensive chemical fertilizers in organic production systems. Furthermore, value-added agri-waste can be a potential feedstock for livestock and industrial products. But comprehensive information concerning agri-waste management is lacking in the literature. Therefore, the present study reviewed the latest advancements in efficient agri-waste management technologies. This latest review will help the researchers and policy planners to formulate environmentally robust residue management practices for achieving a green economy in the agricultural production sector.

Preparation of biochar from constructed wetland plant and its adsorption performance towards Cu2

In order to solve problems in the treatment and disposal of huge production of artificial wetland plants and heavy metal pollution, two constructed wetland plants of reed and gladiolus were selected as raw materials to prepare biochar for adsorbing heavy metals from aqueous solutions. The experimental results showed that reed biochar prepared at 600℃ and activated by KOH with an impregnation ratio of 1:3 (KRAC-3) exhibited relatively high adsorption ability towards Cu²⁺. The optimal results analyzed by Design-Expert software showed that the maximum adsorption rate of KRAC-3 towards Cu²⁺ was obtained under the optimal conditions of adsorbent dosage of 1.2 g/L, pH of 4.96, and reaction time of 137.43 min. The adsorption of Cu²⁺ followed pseudo-second-order kinetics and the Langmuir adsorption model. The theoretical maximum adsorption capacity of KRAC-3 calculated from the Langmuir isotherm model was 148.08 mg/g. Microscopic tests with the help of SEM, EDS, and XRD revealed that physical adsorption, ion exchange, electrostatic adsorption, surface complexation, and precipitation were the main adsorption mechanism of Cu²⁺ loading onto KRAC-3. This study will provide a theoretical basis for the application of biochar prepared from constructed wetland plants and the treatment of heavy metal-containing wastewater.

Preparation of Magnetic Activated Carbon by Activation and Modification of Char Derived from Co-Pyrolysis of Lignite and Biomass and Its Adsorption of Heavy-Metal-Containing Wastewater

Adsorption with activated carbon (AC) is an important method for the treatment of heavy metal wastewater, but there are still certain challenges in the separation and reuse of activated carbon. The preparation of magnetic activated carbon (MAC) by modifying AC is one of the effective means to realize the separation of AC from solution after the adsorption process. In this work, lignite and poplar leaves were used as raw materials for co-pyrolysis, and the co-pyrolysis char was activated and modified to prepare MAC. The structure and properties were characterized by VSM, N2 adsorption, SEM, XRD, and FT-IR. At the same time, the adsorption performance of MAC on wastewater containing Pb and Cd ions was studied. The results show that the prepared MAC contains Fe3O4, and the saturation magnetization (Ms) of the MAC is 13.83 emu/g; the specific surface area of the MAC is 805.86 m2/g, and the micropore volume is 0.23 cm3/g; the MAC exhibited a good porous structure. When the pH value of the solution was 5, the adsorption time was 120 min, the dosage of MAC was 4 g/L, the initial concentration of Pb ion solution was 50 mg/L, and that of Cd ion solution was 25 mg/L, and the adsorption temperature was 30 °C, the adsorption efficiency of Pb, Cd ions were 84.40 and 78.80%, respectively, and the adsorption capacities were 10.55 and 4.93 mg/g, respectively. The adsorption of Pb and Cd ions by MAC conforms to the Langmuir adsorption model, which is a monolayer adsorption. The adsorption process is mainly chemical adsorption, which can be better described by the pseudo-second-order model. The adsorption thermodynamic analysis showed that the adsorption of Pb and Cd ions by MAC was a spontaneous reaction, and the higher the temperature, the stronger the spontaneity.

Kinetic and thermodynamic study on the esterification of oleic acid over SO3H-functionalized eucalyptus tree bark biochar catalyst

Herein, esterification of oleic acid (OA) over tosylic acid functionalized eucalyptus bark biochar (TsOH-MBC) to synthesize fatty acid methyl ester (FAME) was investigated. The TsOH-MBC catalyst was prepared via pyrolysis-activation-sulfonation process at various impregnation ratios and was characterized by SEM, FTIR, EDX, XRD, BET, TGA and acid site density techniques. The catalytic performance of the sulfonated biochar catalyst was described in terms of acidity and FAME yield. 6 g of sulfonic acid loaded on 10 g of MBC (6TsOH-MBC) appeared to be most appropriate combination to achieve a highly active catalyst for the esterification of OA with 96.28% conversion to FAME at 80 °C for 5 h with catalyst loading of 4.0 wt% and 8:1 methanol/OA molar ratio. The catalytic reaction kinetic data were very well described by the second-order model, with a rate coefficient of 0.223 mL mol⁻¹ h⁻¹ at 80 °C and activation energy of 81.77 kJ mol⁻¹. The thermodynamic parameters such as \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta H$$\end{document}ΔH, \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta S$$\end{document}ΔS and \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$\Delta G$$\end{document}ΔG were determined to be 78.94 kJ mol⁻¹, 135.3 J mol⁻¹ K⁻¹ and 33.03 kJ mol⁻¹, respectively. This research provided an environmentally friendly procedure for FAME production that could be replicated on a commercial scale.

Screening the functions of modified rice straw biochar for adsorbing manganese from drinking water

The seasonal out-of-limit of manganese ions (Mn²⁺) in the drinking water reservoirs is an intractable problem to water supply, which can pose a threat to the human health. In this study, the removal of Mn²⁺ by using pristine (BC), pre-alkali (Pre-BC) and post-alkali (Post-BC) modified biochar originating from rice straw was investigated. The maximum adsorption capacities obtained for BC, Pre-BC, and Post-BC were 20.59, 28.37, and 8.06 mg g⁻¹, respectively. The Langmuir isotherm model and the pseudo-second-order kinetic model were suitable fitting models to describe the adsorption process. The investigation of adsorption functions was carried out that revealed that the predominant forces were precipitation and cation exchange with the proportions of 43.38–69.15% and 38.05–55.79%, respectively. With regard to precipitation, Mn(ii) particles (Al–Si–O–Mn and MnCO₃) and insignificantly oxidized insoluble Mn(iv) particles (MnO₂) were formed on the biochar surface. Alkali and alkaline earth metals facilitated the behavior of cation exchange, where the primary contributing ions for cation exchange were Na⁺, Mg²⁺ and Ca²⁺ during the adsorption process. These outcomes suggest that alkali pre-treated modification of biochar is practical for the application of manganese pollution control in lakes and reservoirs.

Modified biochar was used to remove Mn²⁺ from water with principal adsorption functions of precipitation and cation exchange. The MnCO₃ and Al–Si–O–Mn mainly driven precipitation and Na⁺, Mg²⁺ and Ca²⁺ primarily contributed to the cation exchange.

The Removal of Pb2+ from Aqueous Solution by Using Navel Orange Peel Biochar Supported Graphene Oxide: Characteristics, Response Surface Methodology, and Mechanism

The value-added utilization of waste resources to synthesize functional materials is important to achieve the environmentally sustainable development. In this paper, the biochar supported graphene oxide (BGO) materials were prepared by using navel orange peel and natural graphite. The optimal adsorption parameters were analyzed by response surface methodology under the conditions of solution pH, adsorbent dosage, and rotating speed. The adsorption isotherm and kinetic model fitting experiments were carried out according to the optimal adsorption parameters, and the mechanism of BGO adsorption of Pb2+ was explained using Scanning Electron Microscope (SEM-EDS), X-ray Photoelectron Spectroscopy (XPS), X-ray Diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FTIR). Compared with virgin biochar, the adsorption capacity of Pb2+ on biochar supported graphene oxide was significantly increased. The results of response surface methodology optimization design showed that the order of influence on adsorption of Pb2+ was solution pH > adsorbent dosage > rotating speed. The optimal conditions were as follows: solution pH was 4.97, rotating speed was 172.97 rpm, and adsorbent dosage was 0.086 g. In the adsorption−desorption experiment, the desorption efficiency ranged from 54.3 to 63.3%. The process of Pb2+ adsorption by BGO is spontaneous and endothermic, mainly through electrostatic interaction and surface complexation. It is a heterogeneous adsorption process with heterogeneous surface, including surface adsorption, external liquid film diffusion, and intra-particle diffusion.

Waste biomass based potential bioadsorbent for lead removal from simulated wastewater

Present study deals with the lead removal from simulated wastewater using cost effective bio-adsorbent of mango seeds cover with kernel (M), and jamun seeds cover with kernel (JP). Lead removal optimization of adsorption parameters has been analyzed by using Response surface methodology (RSM). The optimum adsorption was attained at speed of 500 rpm, 60 mg, pH 6.5 and contact time of 120 min. The adsorption capacities are around 39.15 mg/g of M and 20.28 mg/g of JP bio-adsorbent, and also the maximum Pb removal were observed ̴ 94.85% and 92.78%, respectively. The regression coefficient was best fitted for both bio-adsorbents are Freundlich model and pseudo-first order reaction kinetic.

Almalki A, F Alkhanani M, Pal DB. Waste seeds of Mangifera indica, Artocarpus heterophyllus, and Schizizium commune as biochar for heavy metal removal from simulated wastewater

The threat of arsenic contamination in water is a challenging issue worldwide. Millions of people utilize untreated groundwater having high levels of arsenic in developing countries. Design Expert 6.0.8 has been used to design experiments and carried out statistical analysis for optimization of different parameters. It is of prime importance to develop cheap environment friendly bio-sorbent for protecting health of the poor from ill effects of arsenic. In the present investigation, we prepared bio-sorbent from the solid waste seed biomass of Mangifera indica (M), Artocarpus heterophyllus (JF), and Schizizium commune (JP). The characterization of bio-sorbents has been done by using different techniques namely FTIR and XRD. Arsenic concentration was estimated using ICP and adsorption parameters optimized for pH, adsorbent dose, and initial arsenic concentration. At pH 8.4, kinetics study of arsenic removal was M (94%), JF (93%), and JP (92%) for initial concentration of 2.5 ppm. The adsorption kinetics was well explained by Freundlich model and pseudo-second reaction order.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s13399-021-02078-5.

Lead removal from synthetic wastewater by biosorbents prepared from seeds of Artocarpus Heterophyllus and Syzygium Cumini

The present investigation deals with removal of lead (Pb⁺²) ions from waste water using biosorbent prepared from seeds of Artocarpus heterophyllus (SBAh) and Syzygium cumini (SBSc). Biosorbents surface has been characterized through FT-IR spectroscopy to probe the presence of functional groups. Response surface methodology enabled optimized conditions (Pb⁺² concentration 2 μg/mL, pH 5.8 and bioadsorbent dose 60 mg) resulted in Pb⁺² removal ~96% for SBAh and ~93% for SBSc at agitation speed 300 rpm. The adsorption capacity has been found to be 4.93 mg/g for SBAh and 3.95 mg/g for SBSc after 70 min. At optimal experimental conditions, kinetics of biosorption was explained well by inter-particle diffusion model for SBAh (R² = 0.99) whereas Elovich model best fitted for SBSc (R² = 0.98). Further, both the biosorbents followed Temkin adsorption isotherm model.

Synergistic advanced oxidation process for enhanced degradation of organic pollutants in spent sulfuric acid over recoverable apricot shell-derived biochar catalyst

The sulfuric acid-based alkylation process, which leads the industrial application market, still struggles with effectively removing a large number of organic pollutants from hazardous spent sulfuric acid. A synergistic advanced oxidation process was constructed to degrade the organic pollutants with H₂O₂ and sodium persulfate as the synergistic oxidants and apricot shell-derived biochar (OBC) as the catalyst. Taking the total organic carbon (TOC) and the color scale as the indices, the effects of critical experimental factors, i.e., reaction temperature, initial oxidant concentration, catalyst dosage, and aeration rate, were optimized. The results showed that the removal rates of TOC and the color of the spent sulfuric acid reached ∼91% and 96.6%, respectively, after 150 min under the optimum conditions. Besides, the efficient and low-cost OBC catalyst developed in this study could be continuously used for at least four times with about 75% TOC removal and 80% color removal, exhibiting favorable stability and good resistance to acid corrosion. Further study confirmed that the SO₄−˙ and ˙OH radicals generated in the synergistic advanced oxidation process strengthened the degradation and elimination of organic pollutants. The synergistic advanced oxidation process could provide a feasible insight for spent sulfuric acid treatment.

A synergistic advanced oxidation process was constructed to degrade the organic pollutants in spent sulfuric acid with apricot shell-derived biochar as the catalyst. It realized the effect of treating waste with waste.

Sustainable removal of arsenic from simulated wastewater using solid waste seed pods biosorbents of Cassia fistula L

The present investigation is focused to develop a new type of solid waste based biosorbent, derived from the Cassia fistula pod biomass. The prepared biosorbent has been characterized through different techniques including field emission scanning electron microscopy, fourier transform infrared spectroscope and X-ray diffraction to investigate the physiochemical properties which are potential for the bioadsorbent application. The experiments have been performed considering four parameters namely; pH, biosorbent dose, initial concentration of As⁺³ and duration in the batch reactor. The experimental results have been analyzed using the design-expert software for the optimization of different parameters. The maximum removal of arsenic could be achieved ∼91% whereas monolayer adsorption capacity is found to be 1.13 mg g^-1 in 80 min at pH 6.0 and 30 °C by using 60 mg dose of bioadsorbent. The arsenic adsorption behavior of the bio-adsorbent has been well interpreted in terms of pseudo-first order and Freundlich model.

Studies on Zero-cost algae based phytoremediation of dye and heavy metal from simulated wastewater

In the present study, filamentous algae, an emerging candidate for biofuel and other useful chemical production, has been investigated as a biological adsorbent for the removal of contaminants from synthetic wastewater. Operational parameters were optimized in batch phytoremediation experiments. The adsorption equilibrium isotherm models such as Langmuir, Freundlich, and Dubinin-Radushkevitch and kinetics models such as pseudo-1st and pseudo-2nd order in methylene blue decolorization and Cr(VI) removal were also investigated. The D-R isotherm theory provided the best fit. The pseudo-2nd order model accurately described the adsorption kinetic data. Maximum adsorption capacities were observed to 5.03 mg.g^-1 and 0.77 mg.g^-1 along with removal efficiencies were achieved to 91.3% and 91.4% for methylene blue and Cr(VI) remediation, respectively. Moreover, intra-particle diffusion kinetic theory was used to describe the mechanism. These outcomes are significant in the development of algae-based zero-cost pollutants removal technology in wastewater treatment.

Sustainable Chromium Recovery From Wastewater Using Mango and Jackfruit Seed Kernel Bio-Adsorbents

Wastewater is a rich source of valuable chemicals of industrial importance. However, their economic recovery is crucial for sustainability. The objective of the present work is to recover hexavalent chromium (Cr VI) as a value-added transition metal from wastewater cost-effectively; the biosorbent derived from seed kernels of mango (M) and jackfruit (JF) were applied for removing the metal from simulated wastewater. The functional groups of the biomass were analysed with the help of Fourier transform infrared (FTIR) spectroscopy, micrographs were generated using a scanning electron microscope, and crystallinity was determined by an x-ray diffractometer (XRD). The concentration of Cr VI in wastewater was analysed by an inductively coupled plasma optical emission spectrometer (ICP-OES). Process parameters (pH, dose, contact time, temperature, and initial concentration) were optimized for efficient Cr VI adsorption using a response surface methodology-based Box-Behnken design (BBD) employing Design-software 6.0.8. The batch experiment at room temperature at pH 4.8 and Cr VI removal ∼94% (M) and ∼92% (JF) was achieved by using a 60-mg dose and an initial Cr (VI) concentration of 2 ppm in 120 min. The equilibrium Cr binding on the biosorbent was well explained using Freundlich isotherm (R ² = 0.97), which indicated the indirect interactions between Cr (VI) and the biosorbent. Biosorption of Cr (VI) followed the pseudo-order and intra-particle diffusion models. The maximum adsorption capacity of the M and JF bio-adsorbent is 517.24 and 207.6 g/mg, respectively. These efficient, cost-effective, and eco-friendly biosorbents could be potentially applied for removing toxic Cr (VI) from polluted water.