EIS-based biosensor for ultra-sensitive detection of TNF-α from non-diluted human serum

Nanophotonic and hydrogel-based diagnostic system for the monitoring of chronic wounds

Chronic wounds present a major healthcare burden, yet most wounds are only assessed superficially, and treatment is rarely based on the analysis of wound biomarkers. This lack of analysis is based on the fact that sampling of wound biomarkers is typically invasive, leading to a disruption of the wound bed while biomarker detection and quantification is performed in a remote laboratory, away from the point of care. Here, we introduce the diagnostic element of a novel theranostic system that can non-invasively sample biomarkers without disrupting the wound and that can perform biomarker quantification at the point of care, on a short timescale. The system is based on a thermally switchable hydrogel scaffold that enhances wound healing through regeneration of the wound tissue and allows the extraction of wound biomarkers non-destructively. We demonstrate the detection of two major biomarkers of wound health, i.e., IL-6 and TNF-α, in human matrix absorbed into the hydrogel dressing. Quantification of the biomarkers directly in the hydrogel is achieved using a chirped guided mode resonant biosensor and we demonstrate biomarker detection within the clinically relevant range of pg/mL to μg/mL concentrations. We also demonstrate the detection of IL-6 and TNF-α at concentration 1 ng/mL in hydrogel dressing absorbed with clinical wound exudate samples. The high sensitivity and the wide dynamic range we demonstrate are both essential for the clinical relevance of our system. Our test makes a major contribution towards the development of a wound theranostic for guided treatment and management of chronic wounds.

A Facile Graphene Conductive Polymer Paper Based Biosensor for Dopamine, TNF-α, and IL-6 Detection

Paper-based biosensors are a potential paradigm of sensitivity achieved via microporous spreading/microfluidics, simplicity, and affordability. In this paper, we develop decorated paper with graphene and conductive polymer (herein referred to as graphene conductive polymer paper-based sensor or GCPPS) for sensitive detection of biomolecules. Planetary mixing resulted in uniformly dispersed graphene and conductive polymer ink, which was applied to laser-cut Whatman filter paper substrates. Scanning electron microscopy and Raman spectroscopy showed strong attachment of conductive polymer-functionalized graphene to cellulose fibers. The GCPPS detected dopamine and cytokines, such as tumor necrosis factor-alpha (TNF-α), and interleukin 6 (IL-6) in the ranges of 12.5-400 µM, 0.005-50 ng/mL, and 2 pg/mL-2 µg/mL, respectively, using a minute sample volume of 2 µL. The electrodes showed lower detection limits (LODs) of 3.4 µM, 5.97 pg/mL, and 9.55 pg/mL for dopamine, TNF-α, and IL-6 respectively, which are promising for rapid and easy analysis for biomarkers detection. Additionally, these paper-based biosensors were highly selective (no serpin A1 detection with IL-6 antibody) and were able to detect IL-6 antigen in human serum with high sensitivity and hence, the portable, adaptable, point-of-care, quick, minute sample requirement offered by our fabricated biosensor is advantageous to healthcare applications.

Nanomaterials and Their Recent Applications in Impedimetric Biosensing

Impedimetric biosensors measure changes in the electrical impedance due to a biochemical process, typically the binding of a biomolecule to a bioreceptor on the sensor surface. Nanomaterials can be employed to modify the biosensor's surface to increase the surface area available for biorecognition events, thereby improving the sensitivity and detection limits of the biosensor. Various nanomaterials, such as carbon nanotubes, carbon nanofibers, quantum dots, metal nanoparticles, and graphene oxide nanoparticles, have been investigated for impedimetric biosensors. These nanomaterials have yielded promising results in improving sensitivity, selectivity, and overall biosensor performance. Hence, they offer a wide range of possibilities for developing advanced biosensing platforms that can be employed in various fields, including healthcare, environmental monitoring, and food safety. This review focuses on the recent developments in nanoparticle-functionalized electrochemical-impedimetric biosensors.

Screen‐printed electrochemical sensors for label‐free potentiometric and impedimetric detection of human serum albumin

Herein, two electrochemical methods based on potentiometric and impedimetric transductions were presented for albumin targeting, employing screen‐printed platforms (SPEs) to make easy and cost‐effective sensors with good detection merits. The SPEs incorporated ion‐to‐electron multi‐walled carbon nanotubes (MWCNTs) transducer. Sensors were constructed using either tridodecyl methyl‐ammonium chloride (TDMACl) (sensor I) or aliquate 336S (sensor II) in plasticized polymeric matrices of carboxylated poly (vinyl chloride) (PVC‐COOH). Analytical performances of the sensors were evaluated using the above‐mentioned electrochemical techniques. For potentiometric assay, constructed sensors responded to albumin with −81.7 ± 1.7 (r2 = 0.9986) and −146.2 ± 2.3 mV/decade (r2 = 0.9991) slopes over the linearity range 1.5 μM–1.5 mM with 0.8 and 1.0 μM detection limits for respective TDMAC‐ and aliquate‐based sensors. Interference study showed apparent selectivity for both sensors. Impedimetric assays were performed at pH = 7.5 in 10 mM PBS buffer solution with a 0.02 M [Fe(CN)6]−3/−4 redox‐active electrolyte. Sensors achieved detection limits of 4.3 × 10−8 and 1.8 × 10−7 M over the linear ranges of 5.2×10−8–1.0×10−4 M and 1.4×10−6–1.4×10−3 M, with 0.09 ± 0.004 and 0.168 ± 0.009 log Ω/decade slopes for sensors based on TDMAC and aliquate, respectively. These sensors are characterized with simple construction, high sensitivity and selectivity, fast response time, single‐use, and cost‐effectiveness. The methods were successfully applied to albumin assessment in different biological fluids.

Electrochemical Biosensors for Whole Blood Analysis: Recent Progress, Challenges, and Future Perspectives

Whole blood, as one of the most significant biological fluids, provides critical information for health management and disease monitoring. Over the past 10 years, advances in nanotechnology, microfluidics, and biomarker research have spurred the development of powerful miniaturized diagnostic systems for whole blood testing toward the goal of disease monitoring and treatment. Among the techniques employed for whole-blood diagnostics, electrochemical biosensors, as known to be rapid, sensitive, capable of miniaturization, reagentless and washing free, become a class of emerging technology to achieve the target detection specifically and directly in complex media, e.g., whole blood or even in the living body. Here we are aiming to provide a comprehensive review to summarize advances over the past decade in the development of electrochemical sensors for whole blood analysis. Further, we address the remaining challenges and opportunities to integrate electrochemical sensing platforms.

Do not let electrode fouling be the enemy of bioanalysis

Electrochemical biosensors are one of the best choices for the sensing of biomarkers due to their high performance, low cost, miniaturization, and wide applicability. However, like for any sensing process, electrode fouling affects severely the analytical performance of the sensor, such as sensitivity, detection limit, reproducibility, and overall reliability. Fouling arises from nonspecific adsorption of different components present in the sensing medium and in particular in complex biofluids such as full blood. The complex composition of blood where biomarkers are present at extremely low concentrations compared to the rest of the fluid composition makes electrochemical biosensing challenging. Direct biomarker analysis within full blood samples remains however central for the future development in electrochemical-based diagnostics. Herein, we aim to provide short discussion of past and more recent strategies and concepts employed to diminish background noise due to surface fouling and overcome current hurdles for the implementation and commercialisation of electrochemical-based biosensors for medical diagnostics of protein biomarkers in a point of care format.

Caco-2 cell-derived biomimetic electrochemical biosensor for cholera toxin detection

Cholera is a highly contagious and lethal waterborne disease induced by an infection with Vibrio cholerae (V. cholerae) secreting cholera toxin (CTx). Cholera toxin subunit B (CTxB) from the CTx specifically binds with monosialo-tetra-hexosyl-ganglioside (GM1) found on the exterior cell membrane of an enterocyte. Bioinspired by the pathological process of CTx, we developed an electrochemical biosensor with GM1-expressing Caco-2 cell membrane (CCM) on the electrode surface. Briefly, the electrode surface was functionalized with CCM using the vesicle fusion method. We determined the CTxB detection performances of Caco-2 cell membrane-coated biosensor (CCB) using electrochemical impedance spectroscopy (EIS). the CCB had an excellent limit of detection of ∼11.46 nM and a detection range spanning 100 ng/mL - 1 mg/mL. In addition, the CCB showed high selectivity against various interfering molecules, including abundant constituents of intestinal fluid and various bacterial toxins. The long-term stability of the CCBs was also verified for 3 weeks using EIS. Overall, the CCB has excellent potential for practical use such as point-of-care and cost-effective testing for CTxB detection in developing countries.

Recent Advances in the Development and Characterization of Electrochemical and Electrical Biosensors for Small Molecule Neurotransmitters

Neurotransmitters act as chemical messengers, determining human physiological and psychological function, and abnormal levels of neurotransmitters are related to conditions such as Parkinson's and Alzheimer's disease. Biologically and clinically relevant concentrations of neurotransmitters are usually very low (nM), so electrochemical and electronic sensors for neurotransmitter detection play an important role in achieving sensitive and selective detection. Additionally, these sensors have the distinct advantage to potentially be wireless, miniaturized, and multichannel, providing remarkable opportunities for implantable, long-term sensing capabilities unachievable by spectroscopic or chromatographic detection methods. In this article, we will focus on advances in the development and characterization of electrochemical and electronic sensors for neurotransmitters during the last five years, identifying how the field is progressing as well as critical knowledge gaps for sensor researchers.

Polyaniline-based electrochemical immunosensor for the determination of antibodies against SARS-CoV-2 spike protein

In this work, we report an impedimetric system for the detection of antibodies against severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) Spike protein. The sensing platform is based on recombinant Spike protein (SCoV2-rS) immobilized on the phytic acid doped polyaniline films (PANI-PA). The affinity interaction between immobilized SCoV2-rS protein and antibodies in the physiological range of concentrations was registered by electrochemical impedance spectroscopy. Analytical parameters of the sensing platform were tuned by the variation of electropolymerization times during the synthesis of PANI-PA films. The lowest limit of detection and quantification were obtained for electropolymerization time of 20 min and equalled 8.00 ± 0.20 nM and 23.93 ± 0.60 nM with an equilibrium dissociation constant of 3 nM. The presented sensing system is label-free and suitable for the direct detection of antibodies against SARS-CoV-2 in real patient serum samples after coronavirus disease 2019 and/or vaccination.

Recent Developments in Electrochemical-Impedimetric Biosensors for Virus Detection

Viruses, including influenza viruses, MERS-CoV (Middle East respiratory syndrome coronavirus), SARS-CoV (severe acute respiratory syndrome coronavirus), HAV (Hepatitis A virus), HBV (Hepatitis B virus), HCV (Hepatitis C virus), HIV (human immunodeficiency virus), EBOV (Ebola virus), ZIKV (Zika virus), and most recently SARS-CoV-2 (severe acute respiratory syndrome coronavirus 2), are responsible for many diseases that result in hundreds of thousands of deaths yearly. The ongoing outbreak of the COVID-19 disease has raised a global concern and intensified research on the detection of viruses and virus-related diseases. Novel methods for the sensitive, rapid, and on-site detection of pathogens, such as the recent SARS-CoV-2, are critical for diagnosing and treating infectious diseases before they spread and affect human health worldwide. In this sense, electrochemical impedimetric biosensors could be applied for virus detection on a large scale. This review focuses on the recent developments in electrochemical-impedimetric biosensors for the detection of viruses.

Incorporating Hydrophobic Moieties into Self-Assembled Monolayers to Enable Electrochemical Aptamer-Based Sensors Deployed Directly in a Complex Matrix

Continuous real-time measurement of specific targets in complex biological samples is of great significance for early diagnosis and treatment of diseases and thus enables achievement of personalized medicine. Electrochemical aptamer-based (E-AB) sensors are good candidates to fill this role due to their high specificity, sensitivity, rapid detection, and simple preparation. However, this sensor class suffers from severe baseline drift in the complex matrix probably due to the nonspecific adsorption of components. Here, we introduce a series of self-assembled monolayers with a variety of hydrophobic functional groups into an E-AB sensor platform, achieving enhancement of the antifouling performance and thus the detection performance (e.g., stability, sensitivity, and specificity). We reveal that the antifouling performance enhanced by such hydrophobic SAMs is probably due to its instant adsorption of components onto the surface, rather than the repelling of these components by hydrophilic SAMs in previous reports.

Nanodiamond conjugated SARS-CoV-2 spike protein: electrochemical impedance immunosensing on a gold microelectrode

A promising immunosensing strategy in diagnosing SARS-CoV-2 is proposed using a 10-µm gap-sized gold interdigitated electrode (AuIDE) to target the surface spike protein (SP). The microelectrode surface was modified by (3-glycidyloxypropyl) trimethoxysilane to enforce the epoxy matrix, which facilitates the immobilization of the anti-SP antibody. The immunosensing performance was evaluated by integrating a nanosized (~ 10 nm) diamond-complexed SP as a target. The proposed immunoassay was quantitatively evaluated through electrochemical impedance spectroscopy (EIS) with the swept frequency from 0.1 to 1 MHz using a 100 mV_RMS AC voltage supply. The immunoassay performed without diamond integration showed low sensitivity, with the lowest SP concentration measured at 1 pM at a determination coefficient of R² = 0.9681. In contrast, the nanodiamond-conjugated SP on the immunosensor showed excellent sensitivity with a determination coefficient of R² = 0.986. SP detection with a nanodiamond-conjugated target on AuIDE reached the low limit of detection at 189 fM in a linear detection range from 250 to 8000 fM. The specificity of the developed immunosensor was evaluated by interacting influenza-hemagglutinin and SARS-CoV-2-nucleocapsid protein with anti-SP. In addition, the authentic interaction of SP and anti-SP was validated by enzyme-linked immunosorbent assay.

Hand-Operated, Paper-Based Rotational Vertical-Flow Immunosensor for the Impedimetric Detection of α-Fetoprotein

This study demonstrates a hand-operated, paper-based rotational vertical-flow immunosensor (rotational VFI) platform requiring fewer pipetting steps, designed for the electrochemical detection of α-fetoprotein with multiple and time-sequenced steps. The platform allows users to perform electrochemical measurements without interference from the convective component of fluid motion, which is unfavorable in most techniques. Users can freely transfer-switch-stop fluid flows by manually rotating the paper disk, evidencing the superior flexibility of this sensor compared to other biosensors. Furthermore, the overall assay duration can be considerably shortened to 9 min. The linear range (LR) is determined to be 0.01-500 ng/mL, with a limit of detection (LOD) of 1.65 pg/mL, and the sensitivity can be significantly enhanced simply by switching off the sample stream to ensure detention at the binding zone (for up to 30 min). This additional step can widen the LR to 0.5 pg/mL, with a LOD of 3.54 fg/mL, which is the lowest detectable level ever reported among paper-based sensors. The advantages of the designed rotational VFI qualify it as a suitable alternative to various biosensors.

Rational design of smart nano-platforms based on antifouling-nanomaterials toward multifunctional bioanalysis

The ability to design nanoprobe devices with the capability of quantitative/qualitative operation in complex media will probably underpin the main upcoming progress in healthcare research and development. However, the biomolecules abundances in real samples can considerably alter the interface performance, where unwanted adsorption/adhesion can block signal response and significantly decrease the specificity of the assay. Herein, this review firstly offers a brief outline of several significances of fabricating high-sensitivity and low-background interfaces to adjust various targets' behaviors induced via bioactive molecules on the surface. Besides, some important strategies to resist non-specific protein adsorption and cell adhesion, followed by imperative categories of antifouling reagents utilized in the construction of high-performance solid sensory interfaces, are discussed. The next section specifically highlights the various nanocomposite probes based on antifouling-nanomaterials for electrode modification containing carbon nanomaterials, noble metal nanoparticles, magnetic nanoparticles, polymer, and silicon-based materials in terms of nanoparticles, rods, or porous materials through optical or chemical strategies. We specially outline those nanoprobes that are capable of identification in complex media or those using new constructions/methods. Finally, the necessity and requirements for future advances in this emerging field are also presented, followed by opportunities and challenges.

Fabrication of MERS-nanovesicle biosensor composed of multi-functional DNA aptamer/graphene-MoS2 nanocomposite based on electrochemical and surface-enhanced Raman spectroscopy

Middle East respiratory syndrome coronavirus (MERS-CoV) is one of the most harmful viruses for humans in nowadays. To prevent the spread of MERS-CoV, a valid detection method is highly needed. For the first time, a MERS-nanovesicle (NV) biosensor composed of multi-functional DNA aptamer and graphene oxide encapsulated molybdenum disulfide (GO-MoS₂) hybrid nanocomposite was fabricated based on electrochemical (EC) and surface-enhanced Raman spectroscopy (SERS) techniques. The MERS-NV aptamer was designed for specifically binding to the spike protein on MERS-NVs and it is prepared using the systematic evolution of ligands by exponential enrichment (SELEX) technique. For constructing a multi-functional MERS aptamer (MF-aptamer), the prepared aptamer was connected to the DNA 3-way junction (3WJ) structure. DNA 3WJ has the three arms that can connect the three individual functional groups including MERS aptamer (bioprobe), methylene blue (signal reporter) and thiol group (linker) Then, GO-MoS₂ hybrid nanocomposite was prepared for the substrate of EC/SERS-based MERS-NV biosensor construction. Then, the assembled multifunctional (MF) DNA aptamer was immobilized on GO-MoS₂. The proposed biosensor can detect MERS-NVs not only in a phosphate-buffered saline (PBS) solution (SERS LOD: 0.176 pg/ml, EIS LOD: 0.405 pg/ml) but also in diluted 10% saliva (SERS LOD: 0.525 pg/ml, EIS LOD: 0.645 pg/ml).

Quench-Release-Based Fluorescent Immunosensor for the Rapid Detection of Tumor Necrosis Factor α

Tumor necrosis factor α (TNF-α) is used as a biomarker for the diagnosis of various inflammatory and autoimmune diseases. In recent years, numerous approaches have been used for the qualitative and quantitative analyses of TNF-α. However, these methods have several drawbacks, such as a tedious and time-consuming process, high pH and temperature sensitivity, and increased chances of denaturation in vitro. Quenchbody (Q-body) is a fluorescence immunoprobe that functions based on the principle of photoinduced electron transfer and has been successful in detecting various substances. In this study, we constructed two Q-bodies based on a therapeutic antibody, adalimumab, to rapidly detect human TNF-α. Both sensors could detect TNF-α within 5 min. The results showed that the limit of detection (LOD) of TNF-α was as low as 0.123 ng/mL with a half-maximal effective concentration (EC₅₀) of 25.0 ng/mL using the TAMRA-labeled Q-body, whereas the ATTO520-labeled Q-body had a LOD of 0.419 ng/mL with an EC₅₀ of 65.6 ng/mL, suggesting that the Q-bodies could rapidly detect TNF-α with reasonable sensitivity over a wide detection range. These biosensors will be useful tools for the detection and monitoring of inflammatory biomarkers.

Simple and facile carbon dots based electrochemical biosensor for TNF-α targeting in cancer patient's sample

Tumour Necrosis Factor (TNF-α) is a pro-inflammatory cytokine having key roles in cell death, differentiation, survival, proliferation, migration and is a modulator of immune system. Therefore, TNF-α is an ideal biomarker for several disease diagnosis including cancer. However, out of all the biomarkers of cancer, TNF-α) is less explored for cancer detection. Only a few reports are available of developing biosensors for TNF-α targeting in human serum samples. Also, Carbon Dots (CDs) remains less explored in biosensor application. In this regard, for the first time, a sensitive and low-cost electrochemical biosensor based on CDs has developed. CDs were synthesized by simple yet facile microwave pyrolysis. Poly methyl methacrylate (PMMA) was selected as the matrix to hold CDs to fabricate the biosensing platform. This novel CD-PMMA nanocomposite featuring excellent biocompatibility, exceptional electrocatalytic conductivity, and large surface area. CD-PMMA was applied as transducing material to efficiently conjugate antibodies specific towards TNF-α and fabricate electrochemical immunosensor for specific detection of TNF-α. The fabricated immunosensor was used for the detection of TNF-α within a wide dynamic range of 0.05-160 pg mL^-1 with a lower detection limit of 0.05 pg mL^-1 and sensitivity of 5.56 pg mL^-1 cm^-2. Furthermore, this CDs based immunosensor retains high sensitivity, selectivity, and stability. This immunosensor demonstrated a high correlation with the conventional technique, Enzyme-Linked Immunosorbent Assay for early screening of cancer patient serum samples.

Fabrication of electrochemical biosensor composed of multi-functional DNA 4 way junction for TNF-α detection in human serum

Tumor necrosis factor (TNF-α) is a representative cytokine family known to induce multiple signaling cascades leading to various cellular responses, such as cell death, survival, and differentiation. It has been reported that blocking the action of TNF-α in various diseases can improve disease prognosis. Therefore, it is important to monitor TNF-α in patient plasma and properly regulate its action. In this study, we report a label-free electrochemical biosensor consisting of a multifunctional DNA 4-way junction (MF-4WJ) for TNF-α detection in human serum. MF-4WJ does not require additional labeling and signal amplification processes. The electrochemical properties of functionalized MF-4WJ were evaluated by cyclic voltammetry (CV) in the presence of Ag⁺ intercalated between the mismatched sequences of MF-aptamers as redox-active species. Afterward, CV was carried out to evaluate the performance of the fabricated biosensor. The proposed label-free electrochemical biosensor was able to effectively detect TNF-α in a dynamic range of 0.15 pg/ml to 150 ng/ml. Limit of detection (LOD) was at 0.07 pg/ml in HEPES. Moreover, it was confirmed that even in 10% diluted human serum, TNF-α could be detected in an excellent dynamic range of 0.15 pg/ml to ∼ 15 ng/ml and LOD was at 0.14 pg/ml in 10% diluted human serum.

Neonatal sepsis at point of care

Sepsis, which includes infection followed by inflammation, is one of the leading causes of death among neonates worldwide. The major attribute of this disease process is dysregulated host response to infection leading to organ dysfunction and potentially death. A comprehensive understanding of the host response as well as the pathogen itself are important factors contributing to outcome. Early diagnosis is paramount, as it leads to accurate assessment and improved clinical management. Accordingly, a number of diagnostic platforms have been introduced to assess the presence of blood stream pathogens in septic neonates. Unfortunately, current point-of-care (POC) methods rely on a single parameter/biomarker and thus lack a comprehensive evaluation. The emerging field of biosensing has, however, resulted in the development of a wide range of analytical devices that may be useful at POC. This review discusses currently available methods to screen the inflammatory process in neonatal sepsis. We describe POC sensor-based methods for single platform multi-analyte detection and highlight the latest advances in this evolving technology. Finally, we critically evaluate the applicability of these POC devices clinically for early diagnosis of sepsis in neonates.

Self-Assembled Monolayers: Versatile Uses in Electronic Devices from Gate Dielectrics, Dopants, and Biosensing Linkers

Self-assembled monolayers (SAMs), molecular structures consisting of assemblies formed in an ordered monolayer domain, are revisited to introduce their various functions in electronic devices. SAMs have been used as ultrathin gate dielectric layers in low-voltage transistors owing to their molecularly thin nature. In addition to the contribution of SAMs as gate dielectric layers, SAMs contribute to the transistor as a semiconducting active layer. Beyond the transistor components, SAMs have recently been applied in other electronic applications, including as remote doping materials and molecular linkers to anchor target biomarkers. This review comprehensively covers SAM-based electronic devices, focusing on the various applications that utilize the physical and chemical properties of SAMs.

"Dual Signal-On" Split-Type Aptasensor for TNF-α: Integrating MQDs/ZIF-8@ZnO NR Arrays with MB-Liposome-Mediated Signal Amplification

Ultrasensitive and accurate detection of biomarkers in serum is of great importance for disease diagnosis and treatment. So far, the commonly used single-mode signal suffers from certain instinct drawbacks that restrict assay performances. Herein, we report the proof-of-concept fabrication of a split-type photoelectrochemical (PEC) and electrochemical (EC) dual-modal aptasensor for ultrasensitively tracing tumor necrosis factor-α, a noteworthy biological biomarker with essential clinical importance. By smart integrating molybdenum disulfide QDs/zeolitic imidazolate framework-8@ZnO nanorod arrays with a methylene blue-liposome-mediated signal amplification strategy, "dual signal-on" detection is accomplished based on a sandwich reaction of the target with aptamer-anchored carboxyl magnetic beads and an aptamer-confined MB liposome. Linear ranges of 5 fg/mL-5 μg/mL (detection limit 1.46 fg/mL) for PEC and 10 fg/mL-0.5 μg/mL (detection limit 6.14 fg/mL) for EC are obtained, respectively. An independent signal transduction mechanism supports the accuracy improvement, and a separate biological process from a translator enables convenient fabrication, short-time consumption, wider linearity, as well as outstanding reproducibility and stability in practical application. This work presents a universal bioassay route with prospects in biomedical and related areas.

Electrochemical Biosensors for Cytokine Profiling: Recent Advancements and Possibilities in the Near Future

Cytokines are soluble proteins secreted by immune cells that act as molecular messengers relaying instructions and mediating various functions performed by the cellular counterparts of the immune system, by means of a synchronized cascade of signaling pathways. Aberrant expression of cytokines can be indicative of anomalous behavior of the immunoregulatory system, as seen in various illnesses and conditions, such as cancer, autoimmunity, neurodegeneration and other physiological disorders. Cancer and autoimmune diseases are particularly adept at developing mechanisms to escape and modulate the immune system checkpoints, reflected by an altered cytokine profile. Cytokine profiling can provide valuable information for diagnosing such diseases and monitoring their progression, as well as assessing the efficacy of immunotherapeutic regiments. Toward this goal, there has been immense interest in the development of ultrasensitive quantitative detection techniques for cytokines, which involves technologies from various scientific disciplines, such as immunology, electrochemistry, photometry, nanotechnology and electronics. This review focusses on one aspect of this collective effort: electrochemical biosensors. Among the various types of biosensors available, electrochemical biosensors are one of the most reliable, user-friendly, easy to manufacture, cost-effective and versatile technologies that can yield results within a short period of time, making it extremely promising for routine clinical testing.

A Label-free Electrochemical Immunosensor for Highly Sensitive Detection of TNF α, Based on Star Polymer-modified disposable ITO Electrode

Background:

Biomarkers are very important disease-related biomolecules which should be analyzed sensitive and selective in related physiological fluids or tissues. Tumor necrosis factor-α is a type of cytokine which plays vitlly important roles in different methabolic pathways such as cell death, survival, differentiation, proliferation and migration, and infectious and inflammatory diseases including rheumatoid arthritis, diabetes.

Objective:

In this study, it was aimed to develop a reliable tool based on star-shaped poly(glycidyl methacrylate) polymer coated disposable indium tin oxide electrode for determination of Tumor necrosis factor-α, an important disease biomarker.

Methods:

Star shaped polymer was used as an interface material for anti- Tumor necrosis factor α antibodies immobilization. The antibodies were immobilized covalently onto polymer coated indium tin oxide electrode. Electrochemical impedance spectroscopy and cyclic voltammetry techniques were used for all electrochemical measurements.

Results:

The suggested immunosensor exhibited a linear range between 0.02 and 4 pg/mL Tumor necrosis factor-α, and the detection limit was found as 6 fg/mL. Scanning electron microscopy and atomic force microscopy were used for electrode surface characterization. In addition, the suggested immunosensor was used for Tumor necrosis factor-α sensing in human serum samples. The results displayed recoveries between 97.07 and 100.19%. Moreover, this immunosensor had a simple fabrication procedure and a long storage-stability.

Conclusion:

A new biosensor based on a Star shaped polymer for the ultra sensitive determination of a biomarker Tumor necrosis factor-α was developed. The biosensor presented excellent repeatability and reproducubility, and also wide calibration range for Tumor necrosis factor- α.

Recent advances in developing biosensing based platforms for neonatal sepsis

Neonatal sepsis is a bloodstream infection primarily caused by Escherichia coli (E. coli), Group B Streptococcus (GBS), Listeria monocytogenes, Haemophilus influenzae, S. aureus, Klebsiella spp. and non-typhoidal Salmonella bacteria. Neonatal Sepsis is referred as a critical response to the infection in the neonatal period that can lead to the failure of body organs and thereby causing damage to the tissues resulting in death of the neonates. Nearly 4 million deaths across the world are occurred due to neonatal sepsis infections. In order to prevent the bloodstream infections in the neonates, it is indispensable to diagnose the disease properly for appropriate treatment during the point of care. Numerous studies have been reported to identify major biomarkers associated with neonatal sepsis including Serum Amyloid A (SAA), C - reactive protein (CRP), Procalcitonin (PCT) and Lipopolysaccharide-binding protein (LBP). Distinct diagnostic platforms have also been developed detecting the presence of bloodstream infections including electrochemical, potentiometric, and impedimetric sensors. Recently, electrochemical biosensors with the integration of nanomaterials have emerged as a better platform for neonatal sepsis biomarkers detection. This review article summarizes the diverse screening platforms, evaluation parameters, and new advances based on implications of nanomaterials for the development of biosensors detecting neonatal sepsis infections. The review further elucidates the significance and future scope of distinctive platforms which are predominantly associated with detection of neonatal sepsis.

Electrochemical ELISA Protein Biosensing in Undiluted Serum Using a Polypyrrole-Based Platform

An electrochemical enzyme-linked immunosorbent assay (ELISA) biosensor platform using electrochemically prepared ~11 nm thick carboxylic functionalized popypyrrole film has been developed for bio-analyte measurement in undiluted serum. Carboxyl polypyrrole (PPy-COOH) film using 3-carboxy-pyrrol monomer onto comb-shaped gold electrode microarray (Au) was prepared via cyclic voltammetry (CV). The prepared Au/PPy-COOH was then utilized for electrochemical ELISA platform development by immobilizing analyte-specific antibodies. Tumor necrosis factor-alpha (TNF-α) was selected as a model analyte and detected in undiluted serum. For enhanced performance, the use of a polymeric alkaline phosphatase tag was investigated for the electrochemical ELISA. The developed platform was characterized at each step of fabrication using CV, electrochemical impedance spectroscopy and atomic force microscopy. The bioelectrodes exhibited linearity for TNF-α in the 100 pg/mL-100 ng/mL range when measured in spiked serum, with limit of detection of 78 pg/mL. The sensor showed insignificant signal disturbance from serum proteins and other biologically important proteins. The developed platform was found to be fast and specific and can be applicable for testing and measuring various biologically important protein markers in real samples.

Magnetic Particles: Their Applications from Sample Preparations to Biosensing Platforms

The growing interest in magnetic materials as a universal tool has been shown by an increasing number of scientific publications regarding magnetic materials and its various applications. Substantial progress has been recently made on the synthesis of magnetic iron oxide particles in terms of size, chemical composition, and surface chemistry. In addition, surface layers of polymers, silica, biomolecules, etc., on magnetic particles, can be modified to obtain affinity to target molecules. The developed magnetic iron oxide particles have been significantly utilized for diagnostic applications, such as sample preparations and biosensing platforms, leading to the selectivity and sensitivity against target molecules and the ease of use in the sensing systems. For the process of sample preparations, the magnetic particles do assist in target isolation from biological environments, having non-specific molecules and undesired molecules. Moreover, the magnetic particles can be easily applied for various methods of biosensing devices, such as optical, electrochemical, and magnetic phenomena-based methods, and also any methods combined with microfluidic systems. Here we review the utilization of magnetic materials in the isolation/preconcentration of various molecules and cells, and their use in various techniques for diagnostic biosensors that may greatly contribute to future innovation in point-of-care and high-throughput automation systems.

Electrochemical immunosensors for the detection of cytokine tumor necrosis factor alpha: A review

In this review, we focus on recent developments in nonlabeled@label-free and labeled@sandwich assay concepts of tumor necrosis factor-alpha (TNF-α) using numerous electrochemical approaches. The fundamental role of such nanostructured materials for the improvement of the analytical response and thus the analytical figures of merit of various TNF-α sensing operations were revealed. Also, this examination focused on recent developments in immuno-electrochemical cytokine TNF-α sensors based on nanostructured materials from 2006 to 2019.

A tetrahedral DNA nanoflare for fluorometric determination of nucleic acids and imaging of microRNA using toehold strands

The authors describe a tetrahedral DNA nanostructure loaded with SYBR Green (SG-TDN) for fluorometric determination of nucleic acids. After intercalating into the TDN, fluorescence of SG is enhanced by 260-fold (exc 480 nm, em 524 nm), and the resulting SG-TDN nanoflare displays >7-fold stronger fluorescence than that of FAM-labeled TDN. The SG-TDNs were coupled to magnetic microparticles and polydopamine nanoparticles to construct multi-functional nanoprobes through sequence hybridization using a toehold strand. The method was applied to detect a stretch of microRNA sequence (20 bp) in buffer and in undiluted serum with excellent selectivity, over a wide linear range and with a low limit of detection (0.2 nM). The probe was also applied for visualization of tumor-related microRNA in living cells via fluorescence imaging. Graphical abstract Schematic representation of tetrahedron-based DNA nanoflare for fluorometric nucleic acid determination in undiluted blood serum and living cells.

Biosensors for Detection of Human Placental Pathologies: A Review of Emerging Technologies and Current Trends

Substantial growth in the biosensor research has enabled novel, sensitive and point-of-care diagnosis of human diseases in the last decade. This paper presents an overview of the research in the field of biosensors that can potentially predict and diagnosis of common placental pathologies. A survey of biomarkers in maternal circulation and their characterization methods is presented, including markers of oxidative stress, angiogenic factors, placental debris, and inflammatory biomarkers that are associated with various pathophysiological processes in the context of pregnancy complications. Novel biosensors enabled by microfluidics technology and nanomaterials is then reviewed. Representative designs of plasmonic and electrochemical biosensors for highly sensitive and multiplexed detection of biomarkers, as well as on-chip sample preparation and sensing for automatic biomarker detection are illustrated. New trends in organ-on-a-chip based placental disease models are highlighted to illustrate the capability of these in vitro disease models in better understanding the complex pathophysiological processes, including mass transfer across the placental barrier, oxidative stress, inflammation, and malaria infection. Biosensor technologies that can be potentially embedded in the placental models for real time, label-free monitoring of these processes and events are suggested. Merger of cell culture in microfluidics and biosensing can provide significant potential for new developments in advanced placental models, and tools for diagnosis, drug screening and efficacy testing.

Magnetic nanoparticles for smart electrochemical immunoassays: a review on recent developments

This review (with 129 refs) summarizes the progress in electrochemical immunoassays combined with magnetic particles that was made in the past 5 years. The specifity of antibodies linked to electrochemical transduction (by amperometry, voltammetry, impedimetry or electrochemiluminescence) gains further attractive features by introducing magnetic nanoparticles (MNPs). This enables fairly easy preconcentration of analytes, minimizes matrix effects, and introduces an appropriate label. Following an introduction into the fundamentals of electrochemical immunoassays and on nanomaterials for respective uses, a large chapter addresses method for magnetic capture and preconcentration of analytes. A next chapter discusses commonly used labels such as dots, enzymes, metal and metal oxide nanoparticles and combined clusters. The large field of hybrid nanomaterials for use in such immunoassays is discussed next, with a focus on MNPs composites with various kinds of graphene variants, polydopamine, noble metal nanoparticles or nanotubes. Typical applications address clinical markers (mainly blood and urine parameters), diagnosis of cancer (markers and cells), detection of pathogens (with subsections on viruses and bacteria), and environmental and food contaminants as toxic agents and pesticides. A concluding section summarizes the present status, current challenges, and highlights future trends. Graphical abstract Magnetic nanoparticles (MNP) with antibodies (Ab) capture and preconcentrate analyte from sample (a) and afterwards become magnetically (b) or immunospecifically (c) bound at an electrode. Signal either increases due to the presence of alabel (b) or decreases as the redox probe is blocked (c).

An integrated adipose-tissue-on-chip nanoplasmonic biosensing platform for investigating obesity-associated inflammation

Although many advanced biosensing techniques have been proposed for cytokine profiling, there are no clinically available methods that integrate high-resolution immune cell monitoring and in situ multiplexed cytokine detection together in a biomimetic tissue microenvironment. The primary challenge arises due to the lack of suitable label-free sensing techniques and difficulty for sensor integration. In this work, we demonstrated a novel integration of a localized-surface plasmon resonance (LSPR)-based biosensor with a biomimetic microfluidic 'adipose-tissue-on-chip' platform for an in situ label-free, high-throughput and multiplexed cytokine secretion analysis of obese adipose tissue. Using our established adipose-tissue-on-chip platform, we were able to monitor the adipose tissue initiation, differentiation, and maturation and simulate the hallmark formation of crown-like structures (CLSs) during pro-inflammatory stimulation. With integrated antibody-conjugated LSPR barcode sensor arrays, our platform enables simultaneous multiplexed measurements of pro-inflammatory (IL-6 and TNF-α) and anti-inflammatory (IL-10 and IL-4) cytokines secreted by the adipocytes and macrophages. As a result, our adipose-tissue-on-chip platform is capable of identifying stage-specific cytokine secretion profiles from a complex milieu during obesity progression, highlighting its potential as a high-throughput preclinical readout for personalized obesity treatment strategies.

Recent advances in biosensors for diagnosis and detection of sepsis: A comprehensive review

Sepsis is one of the leading causes of mortality among critically ill patients globally. According to WHO report 2018, it is estimated to affect beyond 30 million people worldwide every year. It causes loss of human lives, which arise from infection and inflammation and long term stay in intensive care unit (ICU) in hospitals. Despite the availability of satisfactory prognostic markers contributing to the diagnosis of sepsis, millions of people die even after admission to the hospitals. Correct and early diagnosis of sepsis leads to rapid administration of appropriate antibiotics can thus potentially avert the attainment to critical stages of sepsis, thereby saving human lives. Conventional diagnostic practices are costly, time consuming and they lack adequate sensitivity and selectivity, provoking an urgent need for developing alternate sepsis diagnosis systems. Nevertheless, biosensors have the much-treasured scope for reasonable sepsis diagnosis. Advancement in nano-biotechnology has provided new paradigm for biosensor platforms with upgraded features. Here, we provide an overview of the recent advances in biosensors with a brief introduction to sepsis, followed by the conventional methods of diagnosis and bio-sensing. To conclude, a proactive role and an outlook on technologically advanced biosensor platforms are discoursed with possible biomedical applications.

Recent advances in designing nanomaterial based biointerfaces for electrochemical biosensing cardiovascular biomarkers

Early diagnosis of cardiovascular disease (CVD) is critically important for successful treatment and recovery of patients. At present, detection of CVD at early stages of its progression becomes a major issue for world health. The nanoscale electrochemical biosensors exhibit diverse outstanding properties, rendering them extremely suitable for the determination of CVD biomarkers at very low concentrations in biological fluids. The unique advantages offered by electrochemical biosensors in terms of sensitivity and stability imparted by nanostructuring the electrode surface together with high affinity and selectivity of bioreceptors have led to the development of new electrochemical biosensing strategies that have introduced as interesting alternatives to conventional methodologies for clinical diagnostics of CVD. This review provides an updated overview of selected examples during the period 2005-2018 involving electrochemical biosensing approaches and signal amplification strategies based on nanomaterials, which have been applied for determination of CVD biomarkers. The studied CVD biomarkers include AXL receptor tyrosine kinase, apolipoproteins, cholesterol, C-reactive protein (CRP), D-dimer, fibrinogen (Fib), glucose, insulin, interleukins, lipoproteins, myoglobin, N-terminal pro-B-type natriuretic peptide (BNP), tumor necrosis factor alpha (TNF-α) and troponins (Tns) on electrochemical transduction format. Identification of new specific CVD biomarkers, multiplex bioassay for the simultaneous determination of biomarkers, emergence of microfluidic biosensors, real-time analysis of biomarkers and point of care validation with high sensitivity and selectivity are the major challenges for future research.

Recent progress on the sensitive detection of cardiovascular disease markers by electrochemical-based biosensors

Cardiovascular disease is the most reason for deaths in all over the world. Hence, biomarkers of cardiovascular diseases are very crucial for diagnosis and management process. Biomarker detection demand is opened the important way in biosensor development field. Rapid, cheap, portable, precise, selective and sensitive biomarker sensing devices are needed at this point to detect and predict disease. A cardiac biomarker can be orderable as C-reactive protein, troponin I or T, myoglobin, tumor necrosis factor alpha, interleukin-6, interleukin-1, lipoprotein-associated phospholipase, low-density lipoprotein and myeloperoxidase. They are used for prediction of cardiovascular diseases. There are many methods for early diagnosis of cardiovascular diseases, but these have long time process and expensive devices. In recent studies, different biosensors have been developed to remove the problems in this field. Electrochemical devices and developed biosensors have many superiorities than others such as low cost, mobile, reliable, repeatable, need a little amount of solution. In this review, recent studies were presented as details for cardiovascular disease biomarkers detection using electrochemical methods.

Rapid Detection of Tumor Necrosis Factor-Alpha Using Quantum Dot-Based Optical Aptasensor

This paper reports an optical "TURN OFF" aptasensor, which is comprised of a deoxyribonucleic acid aptamer attached to a quantum dot on the terminus and gold nanoparticle on the terminus. The photoluminescence intensity is observed to decrease upon progressive addition of the target protein tumor necrosis factor-alpha (TNF- ) to the sensor. For PBS-based TNF- samples, the beacon exhibited 19%-20% quenching at around 22 nM concentration. The photoluminescence intensity and the quenching efficiency showed a linear decrease and a linear increase, respectively, between 0 to 22.3 nM TNF- . The detection limit of the sensor was found to be 97.2 pM. Specificity test results determined that the sensor has higher selectivity toward TNF- than other control proteins such as C-reactive protein, albumin, and transferrin. The beacon successfully detected different concentrations of TNF- in human serum-based samples exhibiting around 10% quenching efficiency at 12.5 nM of the protein.

An impedimetric bioaffinity sensing chip integrated with the long-range DC-biased AC electrokinetic centripetal vortex produced in a high conductivity solution

Immunoreaction of specific antibodies to antigens is widely used in numerous immunoanalysis applications. However, diffusion-dominated transport in stationary solutions limits the rate and binding density of immunoreaction. This research describes the construction of chip-type concentric multi-double ring electrodes and single central disk electrode. A +1 V-biased 6 V_pp voltage was applied to the multi-double ring electrodes to induce a long-range DC-biased AC electrokinetic flow (ACEKF). The immunoreaction was quantified by electrochemical impedance spectrum (EIS). Fluorescence-labeled secondary antibody (FLSA) and protein A were exemplified as an immunoreacting model to demonstrate the effect of ACEKF on immunoreaction efficiency. The results showed that FLSA binding can reach a plateau in 8 min with the DC-biased ACEKF vortex, and the increment of electron transfer resistance is 2.26 times larger than that obtained in the unstirred solution. The sensitivity of the calibration curves obtained by EIS detection with the aid of DC-biased ACEKF vortex is 1.51 times larger than that obtained in an unstirred solution. The label-free EIS-based sensing chip integrated with the long-range DC-biased ACEKF vortex promises to facilitate immunoreaction efficiency, which is beneficial for the development of a miniature and fast-detection in vitro diagnostic device.

A low-cost and miniaturized potentiostat for sensing of biomolecular species such as TNF-α by electrochemical impedance spectroscopy

Miniaturizing potentiostats, keeping their cost low and yet preserving full measurement characteristics (e.g. bandwidth, determination of capacitive/inductive contribution to sensor's impedance and parallel screening) is still an unresolved challenge in bioelectronics. In this work, the combination of simple analogue circuitry together with powerful microcontrollers and a digital filter implementation is presented as an alternative to complex and incomplete architectures reported in the literature. A low-cost acquisition electronic system fully integrated with a biosensors platform containing eight gold working microelectrodes and integrated reference and counter electrodes was developed and validated. The manufacturing cost of the prototype was kept below 300 USD. The performance of the proposed device was benchmarked against a commercial impedance analyzer through the electrochemical analysis of a highly sensitive biosensor for the detection of tumor necrosis factor α (TNF-α) within the randomly chosen range of 266pg/mL to 666ng/mL in physiological medium (PBS). A strong correlation between the outputs of both devices was found in a critical range of frequencies (1-10Hz), and several TNF-α cytokine concentrations were properly discriminated. These results are very promising for the development of low-cost, portable and miniaturized electrochemical systems for point-of-care and environmental diagnosis.

On-chip immune cell activation and subsequent time-resolved magnetic bead-based cytokine detection

Cytokine profiling and immunophenotyping offer great potential for understanding many disease mechanisms, personalized diagnosis, and immunotherapy. Here, we demonstrate a time-resolved detection of cytokine from a single cell cluster using an in situ magnetic immune assay. An array of triple-layered microfluidic chambers was fabricated to enable simultaneous cell culture under perfusion flow and detection of the induced cytokines at multiple time-points. Each culture chamber comprises three fluidic compartments which are dedicated to, cell culture, perfusion and immunoassay. The three compartments are separated by porous membranes, which allow the diffusion of fresh nutrient from the perfusion compartment into the cell culture compartment and cytokines secretion from the cell culture compartment into the immune assay compartment. This structure hence enables capturing the released cytokines without disturbing the cell culture and without minimizing benefit gain from perfusion. Functionalized magnetic beads were used as a solid phase carrier for cytokine capturing and quantification. The cytokines released from differential stimuli were quantified in situ in non-differentiated U937 monocytes and differentiated macrophages.