Selective adsorption of arsenic over phosphate by transition metal cross-linked chitosan

Critical assessment of recent advancements in chitosan-functionalized iron and geopolymer-based adsorbents for the selective removal of arsenic from water

Inorganic arsenic (As), a known carcinogen and major contaminant in drinking water, affects over 140 million people globally, with levels exceeding the World Health Organization's (WHO) guidelines of 10 μg L-1. Developing innovative technologies for effluent handling and decontaminating polluted water is critical. This paper summarizes the fundamental characteristics of chitosan-embedded composites for As adsorption from water. The primary challenge in selectively removing As ions is the presence of phosphate, which is chemically similar to As(V). This study evaluates and summarizes innovative As adsorbents based on chitosan and its composite modifications, focusing on factors influencing their adsorption affinity. The kinetics, isotherms, column models, and thermodynamic aspects of the sorption processes were also explored. Finally, the adsorption process and implications of functionalized chitosan for wastewater treatment were analyzed. There have been minimal developments in water disinfection using metal-biopolymer composites for environmental purposes. This field of study offers numerous research opportunities to expand the use of biopolymer composites as detoxifying materials and to gain deeper insights into the foundations of biopolymer composite adsorbents, which merit further investigation to enhance adsorbent stability.

Synthesis and characterization of chitosan Schiff base grafted with formaldehyde and aminoethanol: As an effective adsorbent for removal of Pb(II), Hg(II), and Cu(II) ions from aqueous media

Grafted chitosan materials show the characteristics of high stability, easy separation and recovery, and good heavy metal adsorption capacity, and have received much attention in the adsorption process. Therefore, in this work, novel grafted chitosan-based adsorbent CS-EHBSB@F-AE was prepared by a one-pot reaction of chitosan (CS), 3-ethoxy-4-hydroxybenzaldehyde (EHB), formaldehyde (F) and aminoethanol (F). The microstructure and morphology of the as-prepared composite CS-EHBSB@F-AE were characterized by FT-IR, TGA, DSC, FE-SEM, and BET analyses. The adsorption performance of the as-prepared CS-EHBSB@F-AE composite on Pb(II), Hg(II), and Cu(II) ions from aqueous was investigated using batch experiment and the effects of the initial pH of the solution, contact time, and initial metal ions concentration and temperature on the adsorption efficiency were investigated and discussed. At the best conditions, CS-EHBSB@F-AE exhibited remarkable adsorption capacity of 246.7 mg/g, 203.9 mg/g, and 234.4 mg/g in absorbing Pb(II), Hg(II), and Cu(II), respectively. The adsorption equilibrium and the kinetic studies confirmed that the ions adsorption process fits well with the Langmuir isotherm and pseudo-second-order (PSO) models. Additionally, the adsorption efficiency of Pb(II), Hg(II), and Cu(II) metal ions by the composite CS-EHBSB@F-AE was reduced by increasing the temperature from 298 K to 318 K. In addition, after the sixth ads/des cycles, the as-prepared adsorbent still exhibited high removal efficiency with a decrease in adsorption efficiency of Pb(II) (5.53 %), Hg(II) (15.43 %) and Cu(II) (8.27 %). Finally, we proposed that the ions adsorption by CS-EHBSB@F-AE has happened using the coordination of active groups containing nitrogen and oxygen atoms on the surface of the adsorbent with the Pb(II), Hg(II), and Cu(II) metal ions.

Recent advances in chitosan-based nanocomposites for adsorption and removal of heavy metal ions

Due to the high concentration of various toxic and dangerous pollutants, industrial effluents have imposed increasing threats. Among the various processes for wastewater treatment, adsorption is widely used due to its simplicity, good treatment efficiency, availability of a wide range of adsorbents, and cost-effectiveness. Chitosan (CS) has received great attention as a pollutant adsorbent due to its low cost and many -OH and -NH2 functional groups that can bind heavy metal ions. However, weaknesses such as sensitivity to pH, low thermal stability and low mechanical strength, limit the application of CS in wastewater treatment. The modification of these functional groups can improve its performance via cross-linking and grafting agents. The porosity and specific surface area of CS in powder form are not ideal, so physical modification of CS via integration with other materials (e.g., metal oxide, zeolite, clay, etc.) leads to the creation of composite materials with improved absorption performance. This review provides reports on the application of CS and its nanocomposites (NCs) for the removal of various heavy metal ions. Synthesis strategy, adsorption mechanism and influencing factors on sorbents for heavy metals are discussed in detail.

Deep removal of phosphate from electroplating wastewater using novel Fe-MOF loaded chitosan hydrogel beads

Since the electroplating industry is springing up, effective control of phosphate has attracted global concerns. In this study, a novel biosorbent (MIL-88@CS-HDG) was synthesized by loading a kind of Fe-based metal organic framework called MIL-88 into chitosan hydrogel beads and applied in deep treatment of phosphate removal in electroplating wastewater. The adsorption capacities of H2PO4- on MIL-88@CS-HDG could reach 1.1 mmol/g (corresponding to 34.1 mg P/g and 106.7 mg H2PO4-/g), which was 2.65% higher than that on single MOF powders and chitosan hydrogel beads. The H2PO4- adsorption was well described by the Freundlich isotherm model. Over 90% H2PO4- could be adsorbed at contact time of 3 h. It could keep high adsorption capacity in the pH range from 2 to 7, which had a wider pH range of application compared with pure MIL-88. Only NO3- and SO42- limited the adsorption with the reduction rate of 11.42% and 23.23%, proving it tolerated most common co-existing ions. More than 92% of phosphorus could be recovered using NaOH and NaNO3. Electrostatic attraction between Fe core and phosphorus in MIL-88@CS-HDG and ion exchange played the dominant role. The recovered MIL-88@CS-HDG remained stable and applicable in the treatment process of real electroplating wastewater even after six adsorption-regeneration cycles. Based on the removal properties and superb regenerability, MIL-88@CS-HDG is potentially applicable to practical production.

Mechanistic Insights into the Selectivity for Arsenic over Phosphate Adsorption by Fe3+-Cross-Linked Chitosan Using DFT

Fe3+-cross-linked chitosan exhibits the potential for selectively adsorbing arsenic (As) over competing species, such as phosphate, for water remediation. However, the effective binding mechanisms, bond nature, and controlling factor(s) of the selectivity are poorly understood. This study employs ab initio calculations to examine the competitive binding of As(V), P(V), and As(III) to neat chitosan and Fe3+-chitosan. Neat chitosan fails to selectively bind As oxyanions, as all three oxyanions bind similarly via weak hydrogen bonds with preferences of P(V) = As(V) > As(III). Conversely, Fe3+-chitosan selectively binds As(V) over As(III) and P(V) with binding energies of -1.9, -1, and -1.8 eV for As(V), As(III), and P(V), respectively. The preferences are due to varying Fe3+-oxyanion donor-acceptor characteristics, forming covalent bonds with distinct strengths (Fe-O bond ICOHP values: - 4.9 eV/bond for As(V), - 4.7 eV/bond for P(V), and -3.5 eV/bond for As(III)). Differences in pKa between As(V)/P(V) and As(III) preclude any preference for As(III) under typical environmental pH conditions. Furthermore, our calculations suggest that the binding selectivity of Fe3+-chitosan exhibits a pH dependence. These findings enhance our understanding of the Fe3+-oxyanion interaction crucial for preferential oxyanion binding using Fe3+-chitosan and provide a lens for further exploration into alternative transition-metal-chitosan combinations and coordination chemistries for applications in selective separations.

The effect of synthesis conditions on the in situ grown MIL-100(Fe)-chitosan beads: Interplay between structural properties and arsenic adsorption

Efficient sequestration of arsenic from drinking water is a global need. Herein we report eco-friendly porous hybrid adsorbent beads for removal of arsenic, through in situ synthesis of MIL-100(Fe) in the chitosan solvogel. To understand the structural vs. performance correlation, series of hybrid adsorbents were synthesized by modulating synthesis conditions like temperature, crystallization time, and concentration. Adsorbents were investigated using PXRD, FT-IR, SEM, and ICP-OES. Intriguing correlation between crystallinity and adsorption performance was observed as low and high crystalline MIL-100(Fe)-chitosan (ChitFe5 and ChitFe7, respectively) exhibited exceptional adsorption towards As5+ by removing it from water with 99% efficiency, whereas for As3+ species removal of about 85% was afforded. Adsorption isotherms indicated that increase in crystallinity (ChitFe5 -> ChitFe7), adsorption capacities of As5+ and As3+ increased from 23.2 to 64.5, and from 28.1 to 35.3 mg/g, respectively. Selectivity tests of the adsorbents towards As5+ and As3+ over competitive anions in the equimolar competitive systems having nitrates, sulfates, and carbonates demonstrated that the performance of the absorbents was fully maintained, relative to the control system. Through this study a highly selective and efficient adsorbent for arsenic species is designed and a clear insight into the structural tuning and its effect on adsorption performance is provided.

Membrane Functionalization Approaches toward Per- and Polyfluoroalkyl Substances and Selected Metal Ion Separations

Adsorption and ion exchange technologies are two of the most widely used approaches to separate pollutants from water; however, their intrinsic diffusion limitations continue to be a challenge. Pore functionalized membranes are a promising technology that can help overcome these challenges, but the extents of their competitive benefits and broad applicability have not been systematically evaluated. Herein, three types of adsorptive/ion exchange (IX) polymers containing strong/weak acid, strong base, and iron-chitosan complex groups were synthesized in the pores and partially on the surface of microfiltration (MF) membranes and tested for the removal of organic and inorganic cations and anions from water, including arsenic, per- and polyfluoroalkyl substances (PFAS), and calcium (hardness). When directly compared with beads (0.5-6 mm) and crushed resins (0.05 mm), adsorptive/IX pore-functionalized membranes demonstrated an increased relative sorption capacity, up to 2 orders of magnitude faster kinetics and the ability to regenerate up to 70-100% of their capacity while concentrating the initial solution concentration up to 12 times. The simple and versatile synthesis approach used to functionalize membranes, notably independent of the polymer type of the MF membrane, utilized pores throughout the entire cross section of the membrane to immobilize the polymers that contain the functional groups. Utilizing the pore volume of commercial membranes (6-112 mL/m2), the scientific weight capacity of the polymer (3.1-11.5 mequiv/g), and the synthesis conditions (e.g., monomer concentration), the theoretical adsorption/IX capacities per area of the membranes were calculated to be as high as 550 mequiv/m2, substantially higher than the 175 mequiv/m2 value needed to compete with commercially available IX resins. This work therefore shows that pore functionalized membranes are a promising path to tackle water contamination challenges, lowering separation diffusion limitations.

Insights into the selectivity of metallic oxides for arsenic and phosphate from EXAFS and DFT calculations

Phosphate is the biggest competitor for arsenic removal. Nanoscale metal oxides (NMOs) are commonly used to treat arsenic-contaminated water, yet their selective adsorption mechanisms for arsenic and phosphate are poorly understood. We quantified the selectivity of iron oxide (Fe2O3), zinc oxide (ZnO), and titanium dioxide (TiO2) nanosheets for arsenic in systems containing arsenic and phosphate, and determined the interaction of phosphate and arsenate/arsenite on metal oxide surfaces through batch experiments, spectroscopic techniques, and DFT calculations. We found that Fe2O3, TiO2, and ZnO nanosheets exhibit selectivity for arsenate/arsenite in the presence of phosphate, with Fe2O3 the most selective, followed by TiO2 and ZnO. The bonding mechanism on these metallic oxide surfaces dominates the selectivity. The more stable inner-sphere complexes of arsenate on the surfaces of Fe2O3 (bidentate binuclear), TiO2 (bidentate binuclear), and ZnO nanosheets (tridentate trinuclear) contribute to their preference for arsenate over phosphate. This difference in arsenate selectivity can be reflected in the difference in adsorption energy, net electron transfer number, and M - O bond length of the most stable inner sphere complexes. Overall, our study elucidated the selective adsorption mechanisms of arsenate/arsenite on Fe2O3, TiO2, and ZnO surfaces and highlighted the need to consider the competition between arsenate and phosphate during their removal from contaminated water.

Chitosan cross-linked and grafted with epichlorohydrin and 2,4-dichlorobenzaldehyde as an efficient adsorbent for removal of Pb(II) ions from aqueous solution

Epichlorohydrin-modified chitosan-Schiff base composite (CS/24Cl/ECH) prepared via the one-pot reaction as characterized by Fourier transform Infra-Red spectroscopy (FT-IR), X-ray powder diffraction (XRD), Differential scanning calorimetry (DSC) and Scanning electron microscope (SEM). Its removal ability of Pb(II) ions from aqueous solution was investigated. The adsorption of Pb(II) ions carried out at different initial pH, dose of CS/24-Cl/ECH, contact time and co-existing ions. The maximum adsorption capacity of Pb(II) ions was 170 mg/g. Finally, based on the absorption results, the adsorption of Pb(II) ions was fitted by single-layer Langmuir isotherm model and the pseudo-second-order (PSO) kinetics model. The absorption mechanism of Pb(II) ions was controlled by chemical coordination Pb(II) ions with the active sites on the surface of CS/24Cl/ECH composite. Also, CS/24Cl/ECH showed excellent recyclable efficiency up to 5 cycle and potential sorbent for other heavy metal ions.

Review on arsenic environment behaviors in aqueous solution and soil

Arsenic pollution in environment has always been an important environmental problem that has attracted wide attention in recent years. Adsorption is one of the main methods of treatment for arsenic in the aqueous solution and soil because of the advantages of high efficiency, low cost and wide application. Firstly, this report summarizes the commonly and widely used adsorbent materials such as metal-organic frameworks, layered bimetallic hydroxides, chitosan, biochar and their derivatives. The adsorption effects and mechanisms of these materials are further discussed, and the application prospects of these adsorbents are considered. Meanwhile, the gaps and deficiencies in the study of adsorption mechanism was pointed out. Then, this study comprehensively evaluated the effects of various factors on arsenic transport, including (i) the effects of pH and redox potential on the existing form of As; (ii) complexation mechanism of dissolved organic matter and As; (iii) factors affecting the plant enrichment of As. Finally, the latest scientific researches on microbial remediation of arsenic and the mechanisms were summarized. The review finally enlightens the subsequent development of more efficient and practical adsorption material.

Adsorption of Copper and Arsenic from Water Using a Semi-Interpenetrating Polymer Network Based on Alginate and Chitosan

New biobased hydrogels were prepared via a semi-interpenetrating polymer network (semi-IPN) using polyacrylamide/chitosan (PAAM/chitosan) hydrogel for the adsorption of As(V) or poly acrylic acid/alginate (PAA/alginate) hydrogel for the adsorption of Cu(II). Both systems were crosslinked using N,N'-methylenebisacrylamide as the crosslinker and ammonium persulfate as the initiating agent. The hydrogels were characterized by SEM, Z-potential, and FTIR. Their performance was studied under different variables, such as the biopolymer effect, adsorbent dose, pH, contact time, and concentration of metal ions. The characterization of hydrogels revealed the morphology of the material, with and without biopolymers. In both cases, the added biopolymer provided porosity and cavities' formation, which improved the removal capacity. The Z-potential informed the surface charge of hydrogels, and the addition of biopolymers modified it, which explains the further metal removal ability. The FTIR spectra showed the functional groups of the hydrogels, confirming its chemical structure. In addition, the adsorption results showed that PAAM/chitosan can efficiently remove arsenic, reaching a capacity of 17.8 mg/g at pH 5.0, and it can also be regenerated by HNO3 for six cycles. On the other hand, copper-ion absorption was studied on PAA/alginate, which can remove with an adsorption capacity of 63.59 mg/g at pH 4.0, and the results indicate that it can also be regenerated by HNO3 for five cycles.

Pyrolysis self-activation: An environmentally friendly method to transform biowaste into activated carbon for arsenic removal

A green method for production of activated carbon and combustible gas was introduced. Without any external reagents and gases, the H₂O and CO₂ produced by the pyrolysis of bamboo shoot shells were used as activators. The prepared activated carbon had good arsenic adsorption properties with the maximum adsorption capacities of 10.9 mg/g for As(III) and 16.0 mg/g for As(V). The gaseous products were mostly CO and H₂, with higher heating value of 11.7 MJ/Nm³. Thermogravimetric experiments were performed in N₂, H₂O and CO₂ atmospheres to simulate the self-activation process and investigate the self-activation mechanism. This work will help to improve the competitiveness of self-activation technology and reduce the production cost of activated carbon.

Strategic optimization of phase-selective thermochemically amended terra-firma originating from excavation-squander for geogenic fluoride adsorption: a combined experimental and in silico approach

An inimitable adsorbent "FI-TM-BWCC," emanated from meta-phase-selective thermochemical modulation of excavation-squander (mine waste)-derived terra-firma (blackish white china clay, i.e., BWCC), is explored in the present work for fluoride (F^-) adsorption purpose. FI-TM-BWCC portrayed an excellent adsorption efficiency (95% removal capacity and Q_e: 99 mg/g, at initial adsorbate dose: 10 mg/L, pH: 7±0.5, adsorbent dosage: ~600 mg, exposure time: 60 min). At identical experimental conditions, the F^- scavenging phenomenon was superior than two analogous adsorbents: (i) biopolymer chitosan and glutaraldehyde cross-linked BWCC (CG@BWCC, wherein F^- removal efficiency: 74%) and (ii) meta-phase-selective thermally moduled BWCC (TM-BWCC, removal efficiency: 75%). BWCC predominantly comprises kaolinite and a trace amount of anatase along with prime elemental compositions: 41.71% Al₂O₃, 49.80 % SiO₂, 4.25% Fe₂O₃, and 3.93% TiO₂, as revealed by PXRD and XRF analyses. The thermochemical modulation pathway significantly escalated the BET surface area of BWCC (~11.92 m²/g, avg. pore radius: 23.64 Å, i.e., mesoporous in nature) to FI-TM-BWCC (216.95 m²/g, avg. pore radius: 31.41 Å). The fluoride-adsorbed F^-•••FI-TM-BWCC species revealed a reduced surface area of 21.5 m²/g, which was explained in the light of ion exchange pathway on FI-TM-BWCC's non-uniform surface (surface roughness/S_A of 1597 nm, reduced to 1179 nm after F^- uptake). The spontaneous F^-•••FI-TM-BWCC interaction (ΔG⁰ = -6.25 kJ) occurred following chemisorption-controlled ion exchange (CCIE) pathway as appearance of a F1s band at 685.5 eV was rationalized for Si-F bond formation; corroborating pseudo second-order (PSO) kinetics and resembling Freundlich isotherm. The usefulness of FI-TM-BWCC was diversified through field validation with natural groundwater specimens and proposition of a gravity-fed defluoridation unit. The flow rate was documented to be ~11 liters per hour (LPH) by implementing viscous turbulence fluent model. The experimental findings certainly followed the premise conventions of sustainability metrics upholding socio-economic equipoise.

Selective Recovery of Palladium (II) from Metallurgical Wastewater Using Thiadiazole-Based Chloromethyl Polystyrene-Modified Adsorbent

Selective adsorption of palladium from metallurgical wastewater containing Pt (IV), Rh (III), Ca2+, Cu2+, Fe3+, Ni2+, Pb2+, V3+, and Ti4+ has tremendous economic and environmental benefits. In this paper, a novel thiadiazole-based chloromethyl polystyrene-modified adsorbent, viz. 2, 5-bis-polystyrene-1,3,4-thiadiazole (PS-DMTD), was synthesized using chloromethyl polystyrene as the backbone. The experimental results show that PS-DMTD can selectively separate Pd (II) from metallurgical wastewater in a one-step adsorption process. The calculated saturation adsorption capacity of PS-DMTD for Pd (II) was 176.3 mg/g at 25 °C. The separation factors of βPd (II)/Mn+ (Mn+: Pt (IV), Rh (III), Ca2+, Cu2+, Fe3+, Ni2+, Pb2+, V3+, and Ti4+) were all higher than 1 × 104. FT-IR, XPS, and single-crystal X-ray diffraction showed that the adsorption of Pd (II) to PS-DMTD was primarily through a coordination mechanism. Density functional theory (DFT) calculations revealed that the other base metal ions could not coordinate with the PS-DMTD. Pt (IV) could not be adsorbed to PS-DMTD due to its strong chlorophilicity. Furthermore, Rh (III) existed as a polyhydrate, which inhibited Rh (III) diffusion toward the positively charged absorption sites on the PS-DMTD. These results highlight that PS-DMTD has broad application prospects in the recovery of Pd (II) from metallurgical wastewater.

Arsenic in drinking water: overview of removal strategies and role of chitosan biosorbent for its remediation

Accessibility to clean drinking water often remains a crucial task at times. Among other water pollutants, arsenic is considered a more lethal contaminant and has become a serious threat to human life globally. This review discussed the sources, chemistry, distribution, and toxicity of arsenic and various conventional technologies that are in option for its removal from the water system. Nowadays, biosorbents are considered the best option for arsenic-contaminated water treatment. We have mainly focused on the need and potential of biosorbents especially the role of chitosan-based composites for arsenic removal. The chitosan-based sorbents are economically more efficient in terms of their, low toxicity, cost-effectiveness, biodegradability, eco-friendly nature, and reusability. The role of various modification techniques, such as physical and chemical, has also been evaluated to improve the physicochemical properties of biosorbent. The importance of adsorption kinetic and isotherm models and the role of solution pH and pHPZC for arsenic uptake from the polluted water have also been investigated. Some other potential applications of chitosan-based biosorbents have also been discussed along with its sustainability aspect. Finally, some suggestions have been highlighted for further improvements in this field.

Effects of Phosphate, Red Mud, and Biochar on As, Cd, and Cu Immobilization and Enzymatic Activity in a Co-Contaminated Soil

Arsenic (As), cadmium (Cd), and copper (Cu) are the primary inorganic pollutants commonly found in contaminated soils. The simultaneous stabilization of the three elements is a preferred approach for mixture-contaminated soils which has received extensive research attention. However, few studies have focused on the immobilization efficiency of a single amendment on the three elements. In this study, phosphate, red mud, and biochar were used to remediate As (237.8 mg kg−1), Cd (28.72 mg kg−1), and Cu (366.5 mg kg−1) co-contaminated soil using a 180-day incubation study. The BCR (European Community Bureau of Reference) extraction method, NH4H2PO4–extractable As, and diethylenetriamine penta-acetic acid (DTPA)–extractable Cd and Cu were analyzed at different time intervals. The results indicated that the application of red mud and biochar significantly reduced soil DTPA–Cd and Cu concentrations during the incubation, while the decrease in soil NH4H2PO4–As was much less than that of soil DTPA–Cd and Cu. After 180 days of incubation, the concentrations of NH4H2PO4–As in red mud and biochar treatments decreased by 2.15~7.89% and 3.01~9.63%, respectively. Unlike red mud and biochar, phosphate significantly reduced the concentration of soil DTPA–Cd and Cu, but failed to lower that of As. The BCR extraction method confirmed that red mud and biochar addition increased the reducible fraction of As due to the surface complexes of As with Fe oxide. Canonical correspondence analysis (CCA) demonstrated that soil pH in addition to available As, Cd, and Cu concentrations were the primary factors in driving the changes in soil enzymatic activity. Soil pH showed positive correlation with soil urease and catalase activities, while negative correlation was observed between soil-available As, Cd, and Cu, and soil enzyme activities. This study revealed that it is difficult to simultaneously and significantly reduce the bioavailabilities of soil As, Cd, and Cu using one amendment. Further research on modifying these amendments or applying combined amendments will be conducted, in order to develop an efficient method for simultaneously immobilizing As, Cd, and Cu.

Chitosan magnetic graphene grafted polyaniline doped with cobalt oxide for removal of Arsenic(V) from water

The present study reports the successful functionalization/magnetization of bio-polymer to produce chitosan-magnetic graphene oxide grafted polyaniline doped with cobalt oxide (ChMGOP-Co₃O₄). Analytical techniques furrier transform infra-red (FT-IR), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to confirm the formation of ChMGOP-Co₃O₄. The effects of several experimental factors (solution pH, adsorbent dosage and coexisting ions) on the uptake of As(V) ions using ChMGOP-Co₃O₄ were examined through batch experiments. As(V) removal process was validated by experimentally and theoretically investigating the adsorption capacity, rate, and thermal effects. Thermodynamic parameters such as free energy (ΔG°), entropy (ΔS°) and enthalpy (ΔH°) were also calculated and were used to explain the mechanism of adsorption. Based on the results, the sorbent showed a high adsorption capacities (90.91 mg/g) at favorable neutral pH and superior removal efficiencies as high as 89% within 50 min. In addition, the adsorption isotherm followed the Langmuir isotherm in compare to the Freundlich, due to its higher R² value (0.992 < 0.941). Meanwhile, the kinetic data revealed that the of As(V) adsorption was controlled by pseudo-second-order. Overall, the adsorption mechanism studies revealed a spontaneous endothermic nature with predominance of physisorption over chemisorption. This study indicated that ChMGOP-Co₃O₄ is an exceptional novel adsorbent material for the efficient isolation of As(V) from aqueous media.

Efficient removal of heavily oil-contaminated soil using a combination of fenton pre-oxidation with biostimulated iron and bioremediation

Crude oil contamination severely deteriorates soils quality. Bioremediation utilizing soil indigenous organisms could be employed to decompose petroleum hydrocarbons thanks to its low cost and minor environmental disturbance. However, slow kinetics limit the successful application of this biotechnique. Pretreating oil-contaminated soils with Fenton pre-oxidation could accelerate the subsequent bioremediation process. This study was to explore the mechanisms behind the rapid propagation of indigenous petroleum-degrading bacteria (IPDB) and the efficient degradation of total petroleum hydrocarbons (TPH) in soil after Fenton pre-oxidation with biostimulated iron. Biostimulated iron and non-biostimulated iron were used in the experiments, where Fenton pre-oxidation was combined with the bioremediation of oil-contaminated soil (TPH = 13221 mg/kg). Although the amount of Fenton pre-oxidized TPH (3331-3775 mg/kg) was similar with biostimulated and non-biostimulated irons, the biodegradation of TPH after Fenton pre-oxidation with biostimulated iron (5840 mg/kg) was much higher than that with non-biostimulated iron (3034-4034 mg/kg). Moreover, abundant nutrients and a high population of residual IPDB were found after Fenton pre-oxidation with biostimulated iron, which benefited stable consumption of NH₃-N and dissolved organic carbon (DOC) by IPDB during the subsequent bioremediation. However, Fenton pre-oxidation with non-biostimulated iron either resulted in greater damage to IPDB or produced fewer nutrients, thereby failing to ensure the continuous propagation of IPDB during the subsequent bioremediation. Therefore, we propose that Fenton pre-oxidation with biostimulated iron should be applied to heavily oil-contaminated soils prior to bioremediation.

Arsenic removal approaches: A focus on chitosan biosorption to conserve the water sources

Globally, millions of people have no access to clean drinking water and are either striving for that or oppressed to intake polluted water. Arsenic is considered one of the most hazardous contaminants in water bodies that reaches there due to various natural and anthropogenic activities. Modified chitosan has gained much attention from researchers due to its potential for arsenic removal. This review focuses on the need and potential of chitosan-based biosorbents for arsenic removal from water systems. Chitosan is a low-cost, abundant, biodegradable biopolymer that possesses unique structural aspects and functional sites for the adsorption of contaminants like arsenic species from contaminated water. The chitosan-based biosorbents had also been modified using various techniques to enhance their arsenic removal efficiencies. This article reviews various forms of chitosan and parameters involved in chitosan modification which eventually affect the arsenic removal efficiency of the resultant sorbents. The literature revealed that the modified chitosan-based sorbents could express higher adsorption efficiency compared to those prepared from native chitosan. The sustainability of the chitosan-based sorbents has also been considered in terms of reusability. Finally, some recommendations have been underlined for further improvements in this domain.

An Overview on Composite Sorbents Based on Polyelectrolytes Used in Advanced Wastewater Treatment

Advanced wastewater treatment processes are required to implement wastewater reuse in agriculture or industry, the efficient removal of targeted priority and emerging organic & inorganic pollutants being compulsory (due to their eco-toxicological and human health effects, bio-accumulative, and degradation characteristics). Various processes such as membrane separations, adsorption, advanced oxidation, filtration, disinfection may be used in combination with one or more conventional treatment stages, but technical and environmental criteria are important to assess their application. Natural and synthetic polyelectrolytes combined with some inorganic materials or other organic or inorganic polymers create new materials (composites) that are currently used in sorption of toxic pollutants. The recent developments on the synthesis and characterization of composites based on polyelectrolytes, divided according to their macroscopic shape-beads, core-shell, gels, nanofibers, membranes-are discussed, and a correlation of their actual structure and properties with the adsorption mechanisms and removal efficiencies of various pollutants in aqueous media (priority and emerging pollutants or other model pollutants) are presented.

Adsorption of 5-Hydroxymethylfurfural, Levulinic Acid, Formic Acid, and Glucose Using Polymeric Resins Modified with Different Functional Groups

5-hydroxymethylfurfural (5-HMF) is a promising high value-added platform chemical, which can be produced from glucose, fructose, or lignocellulosic biomass via catalysis technology. However, the effective separation of 5-HMF from aqueous solution and actual biomass hydrolysate is still challenging because 5-HMF can be further rehydrated into levulinic acid (LA) and formic acid (FA) under acidic conditions. Herein, the adsorption behavior of glucose and 5-HMF and its follow-up products (LA and FA) from aqueous solutions onto polymeric adsorbents modified with various functional groups (XAD-4, XAD7HP, and XAD761 resins) was systematically investigated. The results showed that XAD761 resin exhibited the highest adsorption selectivity (α5-HMF/glucose = 42.42 ± 5.84, α5-HMF/FA = 18.41 ± 0.50, and α5-HMF/LA = 3.01 ± 0.10) and capacity for 5-HMF (106 mg g-1 wet resin). The adsorption equilibrium was better fitted by the Freundlich isotherm model at the studied range of 5-HMF concentrations. The thermodynamic study and activation energy also revealed that the adsorption process of XAD761 resin for 5-HMF was spontaneous, exothermic, and physical. The kinetic regression results revealed that the kinetic data of 5-HMF was accurately followed by the pseudo-second-order kinetic model. In conclusion, the present study revealed that the potential of phenol formaldehyde resin with hydroxyl groups could be used as an adsorbent for aldehyde organic compounds.

Green Synthesis of A Novel MXene–CS Composite Applied in Treatment of Cr(VI) Contaminated Aqueous Solution

The considerable amount of Cr(VI) pollutants in the aqueous environment is a significant environmental concern that cannot be ignored. A series of novel Mxene–CS inorganic–organic composite nanomaterials synthesized by using the solution reaction method was applied to treat the Cr(VI) contaminated water. The Mxene–CS composites were characterized through SEM (scanning electron microscope), XRD (X–ray diffraction), XPS (X–ray photoelectron spectroscopy), and FTIR (Fourier transform infrared). The XRD patterns (observed at 2θ of 18.1°, 35.8°, 41.5°, and 60.1°) and the FT–IR spectra (-NH2 group for 1635 and 1517 cm−1, and -OH group for 3482 cm−1) illustrated that CS was successfully loaded on the Mxene. The effects of solution pH, the dosage of Mxene–CS, and duration time on the adsorption of Cr(VI) by synthesized Mxene–CS were investigated. The removal efficiency of Cr(VI) was increased from 12.9% to 40.5% with Mxene–CS dosage ranging from 0.02 to 0.12 g/L. The adsorption process could be well fitted by the pseudo–second–order kinetics model, indicating chemisorption occurred. The Langmuir isotherm model could be better to describe the process with a maximum adsorption capacity of 43.1 mg/g. The prepared novel Mxene–CS composite was considered as an alternative for adsorption of heavy metals from wastewater.