Perfluorinated alkyl substances (PFASs) in northern Spain municipal solid waste landfill leachates

Can on-site leachate treatment facilities effectively address the issue of perfluoroalkyl acids (PFAAs) in leachate?

In recent decades, the presence of perfluoroalkyl acids (PFAAs) in municipal solid waste leachate has emerged as a growing concern. Research has focused on PFAA release and occurrence characteristics in landfill and waste-to-energy leachate, highlighting their significant impact when released into wastewater treatment plants. Given the extremely high loading rate faced by current on-site leachate treatment plants (LTPs), the objective of this study is to assess whether the current "anaerobic/aerobic (A/O) + membrane bioreactor (MBR) + nanofiltration (NF) + reverse osmosis (RO)" configuration is effective in PFAAs removal. Concentrations of raw and treated leachate in 10 on-site LTPs with same treatment configuration and varying landfill ages were measured, and a comprehensive mass flow analysis of each treatment process was conducted. The results indicate that A/O treatment has limited capacity for PFAA removal, while NF and RO processes reached 77.44 % and 94.30 % removal rates of ∑PFAAs concentration, respectively. Short-chain PFAAs (> 80 % detected frequency) primarily influenced the distribution and variations of PFAAs in leachate and tend to disperse in the water phase. Correlation analysis revealed the current on-site LTPs exhibit a more efficient removal capacity for long-chain PFAAs.

Characterization of per- and polyfluoroalkyl substances (PFAS) and other constituents in MSW landfill leachate from Puerto Rico

Elevated per- and polyfluoroalkyl substance (PFAS) concentrations have been reported in municipal solid waste (MSW) landfill leachate with higher levels in wet and warmer subtropical climates. Information about landfill leachate characteristics is much more limited in tropical climates. In this study, 20 landfill leachate samples were collected from three MSW landfills on the tropical island of Puerto Rico and results were compared against landfills nationally and within Florida, USA. The samples collected in Puerto Rico underwent physical-chemical analysis, as well as a quantitative analysis of 92 PFAS. Samples described in this study include discrete leachate types, such as leachate, gas condensate, and leachate which has undergone on-site treatment (e.g., RO treatment, phytoremediation, lagoons). A total of 51 PFAS were detected above quantitation limits, including perfluorohexylphosphonic acid, a perfluoroalkyl acid (PFAA) which has not been reported previously in landfill leachate. ∑PFAS concentrations in this study (mean: 38,000 ng L-1), as well as concentrations of individual PFAS, are significantly higher than other reported MSW landfill leachate concentrations. The profiles of leachates collected from on-site treatment systems indicate possible transformation of precursor PFAS as a result of treatment processes - oxidizing conditions, for example, may facilitate aerobic transformation, increase the concentrations of PFAAs, and possibly increase the apparent ∑PFAS concentration. Extreme climate events, including rising temperatures and more frequent hurricanes, have placed additional strain on the solid waste management infrastructure on the island - adding complexity to an already challenging PFAS management issue. As concern grows over PFAS contamination in drinking water, these findings should inform solid waste and leachate management decisions in order to minimize PFAS emissions in island environments.

Distribution of Per- and Polyfluoroalkyl Substances (PFASs) in a Waste-to-Energy Plant─Tracking PFASs in Internal Residual Streams

Per- and polyfluoroalkyl substances (PFASs) constitute a diverse group of man-made chemicals characterized by their water- and oil-repellent properties and persistency. Given their widespread use in consumer products, PFASs will inevitably be present in waste streams sent to Waste-to-Energy (WtE) plants. We have previously observed a subset of PFASs in residual streams (ashes, treated process water, and flue gas) from a WtE plant. However, the transport and distribution of PFASs inside the WtE plant have remained unaddressed. This study is part of a comprehensive investigation to create a synoptic overview of the distribution of PFASs in WtE residues. PFASs were found in all sample types except for boiler ash. The total levels of 18 individual PFASs (Σ18PFASs) in untreated flue gas ranged from 5.2 to 9.5 ng m-3, decreasing with 35% ± 10% after wet flue gas treatment. Σ18PFASs in the condensate ranged from 46 to 50 ng L-1, of which perfluorohexanoic acid (PFHxA) made up 90% on a ng L-1 basis. PFHxA was also dominant in filter ash, where Σ18PFASs ranged from 0.28 to 0.79 ng g-1. This study shows that flue gas treatment can capture some PFASs and transfer them into WtE residues.

Distinctive biotransformation and biodefluorination of 6:2 versus 5:3 fluorotelomer carboxylic acids by municipal activated sludge

Fluorotelomer carboxylic acids (FTCAs) represent an important group of per- and polyfluoroalkyl substances (PFAS) given their high toxicity, bioaccumulation potential, and frequent detection in landfill leachates and PFAS-impacted sites. In this study, we assessed the biodegradability of 6:2 FTCA and 5:3 FTCA by activated sludges from four municipal wastewater treatment plants (WWTPs) in the New York Metropolitan area. Coupling with 6:2 FTCA removal, significant fluoride release (0.56∼1.83 F-/molecule) was evident in sludge treatments during 7 days of incubation. Less-fluorinated transformation products (TPs) were formed, including 6:2 fluorotelomer unsaturated carboxylic acid (6:2 FTUCA), perfluorohexanoic acid (PFHxA), perfluoropentanoic acid (PFPeA), and perfluorobutanoic acid (PFBA). In contrast, little fluoride (0.01∼0.09 F-/molecule) was detected in 5:3 FTCA-dosed microcosms, though 25∼68% of initially dosed 5:3 FTCA was biologically removed. This implies the dominance of "non-fluoride-releasing pathways" that may contribute to the formation of CoA adducts or other conjugates over 5:3 FTCA biotransformation. The discovery of defluorinated 5:3 FTUCA revealed the possibility of microbial attacks of the C-F bond at the γ carbon to initiate the transformation. Microbial community analysis revealed the possible involvement of 9 genera, such as Hyphomicrobium and Dechloromonas, in aerobic FTCA biotransformation. This study unraveled that biotransformation pathways of 6:2 and 5:3 FTCAs can be divergent, resulting in biodefluorination at distinctive degrees. Further research is underscored to uncover the nontarget TPs and investigate the involved biotransformation and biodefluorination mechanisms and molecular basis.

Transport of per-/polyfluoroalkyl substances from leachate to groundwater as affected by dissolved organic matter in landfills

The transport of per- and polyfluoroalkyl substances (PFAS) from landfill leachate to surrounding soil and groundwater poses a threat to human health via the food chain or drinking water. Studies have shown that the transport process of PFAS from the solid to liquid phase in the environment is significantly affected by dissolved organic matter (DOM) adsorption. However, the mechanism of PFAS release from landfill solids into leachate and its transport to the surrounding groundwater remains unclear. In this study, we identified the composition of PFAS and DOM components and analyzed the association between DOM components, physicochemical factors, and PFAS concentrations in landfill leachate and groundwater. This study demonstrated that the frequency of PFAS detection in the samples was 100%, and the PFAS concentrations in leachate were greater than in the groundwater samples. Physicochemical factors, such as ammonium-nitrogen (NH4+-N), sodium (Na), calcium (Ca), DOM components C4 (macromolecular humic acid), SUVA254 (aromatic component content), and A240-400 (humification degree and molecular weight), were strongly correlated with PFAS concentrations. In conclusion, PFAS environmental risk management should be enhanced in landfills, especially in closed landfills, or landfills that are scheduled to close in the near future.

Sorption and diffusion of per-polyfluoroalkyl substances (PFAS) in high-density polyethylene geomembranes

The objective of this study is to investigate the fate and transport of per-polyfluoroalkyl substances (PFAS) through a high-density polyethylene (HDPE) geomembrane (GM) that is commonly used in landfill composite liner systems. Tests were conducted to measure the sorption and diffusion of per-polyfluoroalkyl substances (PFAS) with varying number of carbons in chain and functional groups on HDPE GM. Perfluoroalkyl carboxyl acids (PFCAs), perfluoroalkyl sulphonic acids (PFSAs), alkyl-sulfonamidoacetic acids (FOSAAs), fluorotelomer sulfonic acids (FtSAs), alkane sulfonamides (FOSA) and ether carboxylic acids (Gen X) were investigated in this study. The partition coefficients (Kd) on HDPE GM ranged from 3.8 to 98.3 L/kg. PFAS with amide and sulfonic functional groups showed stronger sorption than that of PFAS with carboxylic acid functional groups. Molecular weight directly affected the Kd for long-chained PFAS whereas the Kd of short-chained PFAS was not sensitive to molecular weight. The diffusion coefficients (Dg) of PFCAs and PFSAs through 0.1-mm HDPE GM were found to be in the orders of 10-18 to 10-17 m2/s. The Dg decreased with increasing molar mass and were also observed to be dependent on the functional group. Dg of PFSAs was lower than that of PFCAs for similar number of carbons in the chain. The estimated mass flux for PFAS in an intact 1.5-mm HDPE GM varied from 38.7 to 2080.8 ng/m2/year whereas the estimated diffusive breakthrough time for PFAS in intact 1.5-mm HDPE was 1526 years or longer.

Field test of thermally activated persulfate for remediation of PFASs co-contaminated with chlorinated aliphatic hydrocarbons in groundwater

The co-occurrence of per- and polyfluoroalkyl substances (PFASs) and chlorinated aliphatic hydrocarbons (CAHs) in groundwater has drawn increased attention in recent years. No studies have been conducted concerning the oxidative degradation of PFASs and/or CAHs by in situ thermally activated persulfate (TAP) in groundwater, primarily due to the difficulty in cost-effectively achieving the desired temperature in the field. In this study, the effects and mechanisms of PFASs degradation by in situ TAP at a site with PFASs and CAHs co-contaminants were investigated. The target temperature of 40.0-70.0 °C was achieved in groundwater, and persulfate was effectively distributed in the demonstration area - the combination of which ensured the degradation of PFASs and CAHs co-contaminants by in situ TAP. It was demonstrated that the reductions of perfluoroalkyl carboxylic acids (PFCAs) concentration in all monitoring wells were in the range of 43.7 %-66.0 % by in situ TAP compared to those maximum rebound values in groundwater, whereas no effective perfluoroalkane sulfonic acids (PFSAs) degradation was observed. The conversion of perfluoroalkyl acids (PFAAs) precursors was one of the main factors leading to the increase in PFCAs concentrations in groundwater during in situ TAP. CAHs were effectively degraded in most monitoring wells, and furthermore, no inhibitory effects of CAHs and Cl- on the degradation of PFASs were observed due to the presence of sufficient persulfate. Additionally, there were significant increases in SO42- concentrations and reductions of pH values in groundwater due to in situ TAP, warranting their long-term monitoring in groundwater. The integrated field and laboratory investigations demonstrated that the reductions in PFCAs and CAHs concentrations can be achieved by the oxidative degradation of in situ TAP.

Inulin alleviates perfluorooctanoic acid-induced intestinal injury in mice by modulating the PI3K/AKT/mTOR signaling pathway

Perfluorooctanoic acid (PFOA) is a widely used industrial compound that has been found to induce intestinal toxicity. However, the underlying mechanisms have not been fully clarified and effective interventions are rarely developed. Inulin, a prebiotic, has been used as a supplement in human daily life as well as in gastrointestinal diseases and metabolic disorders. In this study, male mice were exposed to PFOA with or without inulin supplementation to investigate the enterotoxicity and potential intervention effects of inulin. Mice were administered PFOA at 1 mg/kg/day, PFOA with inulin at 5 g/kg/day, or Milli-Q water for 12 weeks. Histopathological analysis showed that PFOA caused colon shortening, goblet cell reduction, and inflammatory cell infiltration. The expression of the tight junction proteins ZO-1, occludin and claudin5 significantly decreased, indicating impaired barrier function. According to the RNA-sequencing analysis, PFOA exposure resulted in 917 differentially expressed genes, involving 39 significant pathways, such as TNF signaling and cell cycle pathways. In addition, the protein expression of TNF-α, IRG-47, cyclinB1, and cyclinB2 increased, while Gadd45γ, Lzip, and Jam2 decreased, suggesting the involvement of the TNF signaling pathway, cell cycle, and cell adhesion molecules in PFOA-associated intestinal injury. Inulin intervention alleviated PFOA-induced enterotoxicity by activating the PI3K/AKT/mTOR signaling pathway and increasing the protein expression of Wnt1, β-catenin, PI3K, Akt3, and p62, while suppressing MAP LC3β, TNF-α, and CyclinE expression. These findings suggested that PFOA-induced intestinal injury, including inflammation and tight junction disruption, was mitigated by inulin through modifying the PI3K/AKT/mTOR signaling pathways. Our study provides valuable insights into the enterotoxic effects of PFOA and highlights the potential therapeutic role of inulin.

Reductive degradation mechanism of perfluorooctanoic acid (PFOA) during vacuum ultraviolet (VUV) reactions combining with sulfite and iodide

In this study, PFOA removal and defluorination were examined during vacuum ultraviolet (VUV) photolysis in the presence of sulfite and sulfite/iodide conditions. PFOA (24 μM) degradation rate constant (kobs) and defluorination amount in VUV photolysis, and VUV/sulfite, and VUV/sulfite/iodide reactions under nitrogen-purging condition were 5.50 × 10-3, 7.26 × 10-2, 1.60 × 10-1 min-1, and 34.6, 72.7, 73.9% in 6 h, respectively. When tert-butanol (t-BuOH), NO2-, and NO3- ions were added as radical scavengers, hydrated electrons (eaq-) was confirmed as the main species responsible for degrading PFOA and mediating defluorination in VUV-based reactions. While, during VUV photolysis, short-chain perfluoroalkyl carboxylic acids (PFCAs), such as PFHpA, PFHxA, PFPeA, and PFBA, were mainly produced as transformation products (TPs) by the chain-shortening mechanism, additional 14 and 15 TPs were identified in the VUV/sulfite and VUV/sulfite/iodide reactions by LC-QTOF/MS, respectively. The main degradation mechanisms in these reactions are H-F exchange (e.g., TP395 (m/z = 394.9739) and TP377 (m/z = 376.9838)), •SO3--F exchange (TP474, m/z = 474.9323), carbon double bond formation by defluorination (e.g., TP392 (m/z = 392.9455), TP410 (m/z = 410.9355), and TP436 (m/z = 436.9347)), and H-F exchange followed by hydration reaction (TP393, m/z = 392.9773), respectively. PFOA degradation pathways were proposed for these VUV-based reactions based on the identified TPs, their time profiles, and the density functional theory (DFT). Finally, the toxicity of PFOA and its TPs produced during three reactions were assessed using ECOSAR simulation.

A critical review of perfluoroalkyl and polyfluoroalkyl substances (PFAS) landfill disposal in the United States

Landfills manage materials containing per- and polyfluoroalkyl substances (PFAS) from municipal solid waste (MSW) and other waste streams. This manuscript summarizes state and federal initiatives and critically reviews peer-reviewed literature to define best practices for managing these wastes and identify data gaps to guide future research. The objective is to inform stakeholders about waste-derived PFAS disposed of in landfills, PFAS emissions, and the potential for related environmental impacts. Furthermore, this document highlights data gaps and uncertainties concerning the fate of PFAS during landfill disposal. Most studies on this topic measured PFAS in liquid landfill effluent (leachate); comparatively fewer have attempted to estimate PFAS loading in landfills or other effluent streams such as landfill gas (LFG). In all media, the reported total PFAS heavily depends on waste types and the number of PFAS included in the analytical method. Early studies which only measured a small number of PFAS, predominantly perfluoroalkyl acids (PFAAs), likely report a significant underestimation of total PFAS. Major findings include relationships between PFAS effluent and landfill conditions - biodegradable waste increases PFAS transformation and leaching. Based on the results of multiple studies, it is estimated that 84% of PFAS loading to MSW landfills (7.2 T total) remains in the waste mass, while 5% leaves via LFG and 11% via leachate on an annual basis. The environmental impact of landfill-derived PFAS has been well-documented. Additional research is needed on PFAS in landfilled construction and demolition debris, hazardous, and industrial waste in the US.

A review of liquid crystal monomers: Environmental occurrence, degradation, toxicity, and human exposure of an emerging class of E-waste pollutants

Liquid crystal monomers (LCMs) are a class of organic compounds with diphenyl or dicyclohexane as the skeleton structure, which are widely used in the manufacturing of liquid crystal displays. They are recognized as novel organic compounds with persistence, bioaccumulation, toxicity, and potential for long-range transport. LCMs are inevitably released into the environment throughout the life cycle of electronic products, and their presence has been found in various abiotic matrixes (air, dust, sediment, leachate, soil) and biotic matrixes (aquatic organisms, human serum, and human skin wipe). Given that studies on LCMs are still in their infancy, this review comprehensively summarizes the extensive literature data on LCMs and identifies key knowledge gaps and future research needs. The physicochemical properties, production, and usage of LCMs are described. Their environmental distribution, degradation, toxicity, and human exposure are also discussed based on the available data and results. Existing data show that LCMs have large-scale environmental pollution and may pose potential ecological and health risks, but it is still insufficient to accurately assess their risks due to the lack of knowledge on LCMs in many areas, such as global contamination trend, environmental behavior, toxic effects, and human exposure assessment. We believe that future studies of LCMs need to investigate LCMs pollution on a large geographic scale, explore their sources, behavior, and fate in the environment, and assess their potential health hazards to organisms and humans.

A ReaxFF-based molecular dynamics study of the destruction of PFAS due to ultrasound

This work uses a computational approach to provide a mechanistic explanation for the experimentally observed destruction of per- and polyfluoroalkyl substances (PFAS) in water due to ultrasound. The PFAS compounds have caused a strong public and regulatory response due to their ubiquitous presence in the environment and toxicity to humans. In this research, ReaxFF -based Molecular Dynamics simulation under several temperatures ranging from 373 K to 5,000 K and different environments such as water vapor, O2, N2, and air were performed to understand the mechanism of PFAS destruction. The simulation results showed greater than 98% PFAS degradation was observed within 8 ns under a temperature of 5,000 K in a water vapor phase, replicating the observed micro/nano bubbles implosion and PFAS destruction during the application of ultrasound. Additionally, the manuscript discusses the reaction pathways and how PFAS degradation evolves providing a mechanistic basis for the destruction of PFAS in water due to ultrasound. The simulation showed that small chain molecules C1 and C2 fluoro-radical products are the most dominant species over the simulated period and are the impediment to an efficient degradation of PFAS. Furthermore, this research confirms the empirical findings observations that the mineralization of PFAS molecules occurs without the generation of byproducts. These findings highlight the potential of virtual experiments in complementing laboratory experiments and theoretical projections to enhance the understanding of PFAS mineralization during the application of ultrasound.

Impact of effluent organic matter on perfluoroalkyl acid removal from wastewater effluent by granular activated carbon and alternative adsorbents

Occurrence of perfluoroalkyl acids (PFAAs) in wastewater effluent coupled with increasingly stringent regulations has increased the need for more effective sorption-based PFAA treatment approaches. This study investigated the impact of ozone (O3)- biologically active filtration (BAF) as integral components of non-reverse osmosis (RO)-based potable reuse treatment trains and as a potential pretreatment option to improve adsorptive PFAA removal from wastewater effluent by nonselective (e.g., granular activated carbon (GAC) and selective (e.g., anionic exchange resins (AER) and surface-modified clay (SMC)) adsorbents. For nonselective GAC, O3 and BAF resulted in similar PFAA removal improvements, while BAF alone performed better than O3 for AER and SMC. O3-BAF in tandem resulted in the highest PFAA removal performance improvement among pretreatments investigated for selective and nonselective adsorbents. Side by side evaluation of the dissolved organic carbon (DOC) breakthrough curves and size exclusion chromatography (SEC) for each pretreatment scenario suggested that despite the higher affinity of selective adsorbents towards PFAAs, the competition between PFAA and effluent organic matter (EfOM) (molecular weights (MWs): 100-1000 Da) negatively impacts the performance of these adsorbents. The SEC results also demonstrated that transformation of hydrophobic EfOM to more hydrophilic molecules during O3 and biotransformation of EfOM during BAF were the dominant mechanisms responsible for alleviating the competition between PFAA and EfOM, resulting in PFAA removal improvement.

Poly- and Perfluoroalkyl Substances (PFAS): Do They Matter to Aquatic Ecosystems?

Poly- and perfluoroalkyl substances (PFASs) are a group of anthropogenic chemicals with an aliphatic fluorinated carbon chain. Due to their durability, bioaccumulation potential, and negative impacts on living organisms, these compounds have drawn lots of attention across the world. The negative impacts of PFASs on aquatic ecosystems are becoming a major concern due to their widespread use in increasing concentrations and constant leakage into the aquatic environment. Furthermore, by acting as agonists or antagonists, PFASs may alter the bioaccumulation and toxicity of certain substances. In many species, particularly aquatic organisms, PFASs can stay in the body and induce a variety of negative consequences, such as reproductive toxicity, oxidative stress, metabolic disruption, immunological toxicity, developmental toxicity, cellular damage and necrosis. PFAS bioaccumulation plays a significant role and has an impact on the composition of the intestinal microbiota, which is influenced by the kind of diet and is directly related to the host's well-being. PFASs also act as endocrine disruptor chemicals (EDCs) which can change the endocrine system and result in dysbiosis of gut microbes and other health repercussions. In silico investigation and analysis also shows that PFASs are incorporated into the maturing oocytes during vitellogenesis and are bound to vitellogenin and other yolk proteins. The present review reveals that aquatic species, especially fishes, are negatively affected by exposure to emerging PFASs. Additionally, the effects of PFAS pollution on aquatic ecosystems were investigated by evaluating a number of characteristics, including extracellular polymeric substances (EPSs) and chlorophyll content as well as the diversity of the microorganisms in the biofilms. Therefore, this review will provide crucial information on the possible adverse effects of PFASs on fish growth, reproduction, gut microbial dysbiosis, and its potential endocrine disruption. This information aims to help the researchers and academicians work and come up with possible remedial measures to protect aquatic ecosystems as future works need to be focus on techno-economic assessment, life cycle assessment, and multi criteria decision analysis systems that screen PFAS-containing samples. New innovative methods requires further development to reach detection at the permissible regulatory limits.

Emission of Per- and Polyfluoroalkyl Substances from a Waste-to-Energy Plant─Occurrence in Ashes, Treated Process Water, and First Observation in Flue Gas

Per- and polyfluoroalkyl substances (PFASs) are a large group of compounds commonly used as industrial chemicals and constituents of consumer products, e.g., as surfactants and surface protectors. When products containing PFASs reach their end of life, some end up in waste streams sent to waste-to-energy (WtE) plants. However, the fate of PFASs in WtE processes is largely unknown, as is their potential to enter the environment via ash, gypsum, treated process water, and flue gas. This study forms part of a comprehensive investigation of the occurrence and distribution of PFASs in WtE residues. Sampling was performed during incineration of two different waste mixes: normal municipal solid waste incineration (MSWI) and incineration of a waste mix with 5-8 wt % sewage sludge added to the MSWI (referred to as Sludge:MSWI). PFASs were identified in all examined residues, with short-chain (C4-C7) perfluorocarboxylic acids being the most abundant. Total levels of extractable PFASs were higher during Sludge:MSWI than during MSWI, with the total annual release estimated to be 47 and 13 g, respectively. Furthermore, PFASs were detected in flue gas for the first time (4.0-5.6 ng m^-3). Our results demonstrate that some PFASs are not fully degraded by the high temperatures during WtE conversion and can be emitted from the plant via ash, gypsum, treated process water, and flue gas.

Per- and Polyfluoroalkyl Substances in Personal Hygiene Products: The Implications for Human Exposure and Emission to the Environment

Per- and polyfluoroalkyl substances (PFAS) have been related to reproductive toxicity in humans, but their occurrence in some specific personal hygiene products, i.e., sanitary pads, panty liners, tampons, paper diapers, menstrual cups, and bactericidal liquids, has not been extensively studied. This work investigated 31 representative PFAS in six categories of such personal hygiene products (n = 91). Perfluorinated carboxylic acids were the primary PFAS found in the samples, accounting for over 85% of the total concentrations of PFAS. Paper diapers contained the highest sum of PFAS concentrations (64.6 ng/g) followed by sanitary pads (52.3 ng/g) and menstrual cups (21.1 ng/g). The estimated exposure doses of perfluorooctanoic acid through dermal absorption from the use of menstrual cups and paper diapers for infants (adults) were 0.77 and 2.1 (1.2) ng/kg-bw/day, which contributed more than normal dust ingestion. The estimated emission of paper diapers and sanitary pads into the environment was 2.58 and 322 kg/year with an assumed leaching rate of 100%. The potential exposure of PFAS through the use of personal hygiene products observed in this work suggests a previously unreported exposure pathway of these chemicals to humans.

PFAS in municipal landfill leachate: Occurrence, transformation, and sources

To understand sources and processes affecting per- and polyfluoroalkyl substances (PFAS), 32 PFAS were measured in landfill leachate from 17 landfills across Washington State in both pre-and post-total oxidizable precursor (TOP) assay samples, using an analytical method that was the precursor to EPA Draft Method 1633. As in other studies, 5:3FTCA was the dominant PFAS in the leachate, suggesting that carpets, textiles, and food packaging were the main sources of PFAS. Total PFAS concentrations (Σ₃₂PFAS) ranged from 61 to 172,976 ng/L and 580-36,122 ng/L in pre-TOP and post-TOP samples, respectively, suggesting that little or no uncharacterized precursors remained in landfill leachate. Furthermore, due to chain-shortening reactions, the TOP assay often resulted in a loss of overall PFAS mass. Positive matrix factorization (PMF) analysis of the combined pre- and post-TOP samples produced five factors that represent sources and processes. Factor 1 consisted primarily of 5:3FTCA (intermediate of 6:2 fluorotelomer degradation and characteristic of landfill leachate), while factor 2 was dominated by PFBS (degradant of C-4 sulfonamide chemistry) and, to a lesser extent, by several PFCAs and 5:3FTCA. Factor 3 consisted primarily of both short-chain PFCAs (end-products of 6:2 fluorotelomer degradation) and PFHxS (derived from C-6 sulfonamide chemistry), while the main component of factor 4 was PFOS (dominant in many environmental media but minor in landfill leachate, perhaps reflecting a production shift from longer to shorter chain PFAS). Factor 5, highly loaded with PFCAs, was dominant in post-TOP samples and therefore represented the oxidation of precursors. Overall, PMF analysis suggests that the TOP assay approximates some redox processes which occur in landfills, including chain-shortening reactions which yield biodegradable products.

Suspect screening and total oxidizable precursor (TOP) assay as tools for characterization of per- and polyfluoroalkyl substance (PFAS)-contaminated groundwater and treated landfill leachate

Landfill facilities are a major source of release of per- and polyfluoroalkyl substances (PFAS) to the surrounding environment. In this study, landfill leachate treated in a conventional wastewater treatment plant and PFAS-contaminated groundwater were subjected to suspect screening analysis and semi-quantification using total oxidizable precursor (TOP) assay and liquid chromatography coupled to high-resolution mass spectrometry (LC-HRMS). TOP assays yielded expected results for legacy PFAS and their precursors, but showed no discernible evidence of degradation of perfluoroethylcyclohexane sulfonic acid. TOP assays also produced significant evidence of presence of precursors in both treated landfill leachate and groundwater, but the majority of precursors had probably degraded into legacy PFAS after many years in the landfill. Suspect screening identified a total of 28 PF AS, of which six were not included in the targeted method and were identified with confidence level (CL) ≥3. Semi-quantification of these six compounds showed very low concentrations, indicating that they are not as great a concern as the target PFAS.

A Review: Per- and Polyfluoroalkyl Substances-Biological Degradation

Per- and polyfluoroalkyl substances (PFASs), highly stable synthetic organic compounds with multiple carbon-fluorine bonds, are emerging as environmental contaminants, toxic, bioaccumulative, and environmentally persistent. PFASs are strongly resistant to biological and chemical degradation, and therefore PFASs present a challenge to researchers and scientists for a better understanding and application of remediation methods and biodegradation of PFASs and have become subject to strict government regulations. The review summarizes the recent knowledge of bacterial and fungal degradation of PFASs, as well as the enzymes involved in the processes of transformation/degradation of PFASs.

A review of the occurrence, transformation, and removal technologies for the remediation of per- and polyfluoroalkyl substances (PFAS) from landfill leachate

Per- and polyfluoroalkyl substances (PFAS) are persistent organic pollutants (POPs) that pose significant environmental and human health risks. The presence of PFAS in landfill leachate is becoming an increasingly concerning issue. This article presents a comprehensive review of current knowledge and research gaps in monitoring and removing PFAS from landfill leachate. The focus is on evaluating the effectiveness and sustainability of existing removal technologies, and identifying areas where further research is needed. To achieve this goal, the paper examines the existing technologies for monitoring and treating PFAS in landfill leachate. The review emphasizes the importance of sample preparation techniques and quality assurance/quality control measures in ensuring accurate and reliable results. Then, this paper reviewed the existing technologies for removal and remediation of PFAS in landfill leachates, such as adsorption, membrane filtration, photocatalytic oxidation, electrocatalysis, biodegradation, and constructed wetlands. Additionally, the paper summarizes the factors that exhibit the performance of various treatment technologies: reaction time, experimental conditions, and removal rates. Furthermore, the paper evaluates the potential application of different remediation technologies (i.e., adsorption, membrane filtration, photocatalytic oxidation, electrocatalysis, biodegradation, and constructed wetlands, etc.) in treating landfill leachate containing PFAS and its precursors, such as fluorotelomeres like FTOH and FTSs. The review highlights the importance of considering economic, technical, and environmental factors when selecting control measures. Overall, this article aims to provide guidance for promoting environmental protection and sustainable development in the context of PFAS contamination in landfill leachate.

Bioavailability, phytotoxicity and plant uptake of per-and polyfluoroalkyl substances (PFAS): A review

Per- and polyfluoroalkyl substances (PFAS) are a group of legacy and emerging contaminants containing at least one aliphatic perfluorocarbon moiety. They display rapid and extensive transport in the environment due to their generally high water-solubility and weak adsorption onto soil particles. Because of their widespread presence in the environment and known toxicity, PFAS has become a serious threat to the ecosystem and public health. Plants are an essential component of the ecosystem and their uptake and accumulation of PFAS affect the fate and transport of PFAS in the ecosystem and has strong implications for human health. It is therefore imperative to investigate the interactions of plants with PFAS. This review presents a detailed discussion on the mechanisms of the bioavailability and plant uptake of PFAS, and essential factors affecting these processes. The phytotoxic effects of PFAS at physiological, biochemical, and molecular level were also carefully reviewed. At the end, key research gaps were identified, and future research needs were proposed.

A critical review of the occurrence, fate and treatment of per- and polyfluoroalkyl substances (PFASs) in landfills

The aim of this critical review is i) to summarize the occurrence of Per- and polyfluoroalkyl substances (PFASs) in landfills; ii) to outline the environmental fate and transport of PFASs in landfills; iii) to compare the treatment technologies of PFASs in landfill leachate and remediation methods of PFASs in surrounding groundwater; iv) to identify the research gaps and suggest future research directions. In recent years, PFASs have been detected in landfills around the world, among which Perfluoroalkyl acids (PFAAs) especially Perfluorooctanoic acid (PFOA) and Perfluorooctane sulfonic acid (PFOS) are mostly studied due to their long-term stability. Short-chain PFASs (<8 carbons) are more common than long-chain PFASs (≧8 carbons) in landfill leachate. PFASs in landfill leachate are eventually transported to the surrounding groundwater, surface water and soil. Some PFASs evaporate from landfills to the ambient air. To avoid the environmental and health risks of PFASs in landfills, new technologies and combined use of existing technologies have been implemented to treat PFASs in landfill leachate. Integrated remediation methods are applied to control the diffusion of PFASs in groundwater surrounding landfills. In future, the mechanisms of PFAAs precursors degradation, the correlation among PFASs in different environmental media around landfills, as well as the environmental behavior and toxic effect of combined pollutants together with PFASs in landfill leachate and surrounding groundwater should be studied.

Occurrence and removal of per- and polyfluoroalkyl substances (PFAS) in leachates from incineration plants: A full-scale study

Municipal solid wastes (MSWs) contain diverse per- and polyfluoroalkyl substances (PFAS), and these substances may leach into leachates, resulting in potential threats to the environment and human health. In this study, leachates from incineration plants with on-site treatment systems were measured for 17 PFAS species, including 13 perfluorocarboxylic acids (PFCAs) and 4 perfluorosulfonic acids (PFSAs). PFAS were detected in all of the raw leachates and finished effluents in concentrations ranging from 7228 to 16,565 ng L^-1 and 43 to 184 ng L^-1, respectively, with a greater contribution from the short-chain PFAS and PFCAs. The results showed that the existing combined processes (biological treatment and membrane filtration) were effective in decreasing PFAS in the aqueous phase with removal efficiencies over 95%. In addition, correlation analysis suggested that physical entrapment, not biodegradation, was the main means of PFAS reduction in the treatment system. These results filled a gap in the understanding of PFAS occurrence and removal in leachates from incineration plants during the full-scale treatment processes, and demonstrated those leachates were previously under-explored sources of PFAS.

Poly- and Perfluoroalkyl Substances (PFAS) in Landfills: Occurrence, Transformation and Treatment

Landfills have served as the final repository for > 50 % municipal solid wastes in the United States. Because of their widespread uses and persistence in the environment, per- and polyfluoroalkyl substances (PFAS) (>4000 on the global market) are ubiquitously present in everyday consumer, commercial and industrial products, and have been widely detected in both closed (tens ng/L) and active (thousands to ten thousands ng/L) landfills due to disposal of PFAS-containing materials. Along with the decomposition of wastes in-place, PFAS can be transformed and released from the wastes into leachate and landfill gas. Consequently, it is critical to understand the occurrence and transformation of PFAS in landfills and the effectiveness of landfills, as a disposal alternative, for long-term containment of PFAS. This article presents a state-of-the-art review on the occurrence and transformation of PFAS in landfills, and possible effect of PFAS on the integrity of modern liner systems. Based on the data published from 10 countries (250 + landfills), C4-C7 perfluoroalkyl carboxylic acids were found predominant in the untreated landfill leachate and neutral PFAS, primarily fluorotelomer alcohols, in landfill air. The effectiveness and limitations of the conventional leachate treatment technologies and emerging technologies were also evaluated to address PFAS released into the leachate. Among conventional technologies, reverse osmosis (RO) may achieve a high removal efficiency of 90-100 % based on full-scale data, which, however, is vulnerable to the organic fouling and requires additional disposal of the concentrate. Implications of these knowledge on PFAS management at landfills are discussed and major knowledge gaps are identified.

A Review of PFAS Destruction Technologies

Per- and polyfluoroalkyl substances (PFASs) are a family of highly toxic emerging contaminants that have caught the attention of both the public and private sectors due to their adverse health impacts on society. The scientific community has been laboriously working on two fronts: (1) adapting already existing and effective technologies in destroying organic contaminants for PFAS remediation and (2) developing new technologies to remediate PFAS. A common characteristic in both areas is the separation/removal of PFASs from other contaminants or media, followed by destruction. The widely adopted separation technologies can remove PFASs from being in contact with humans; however, they remain in the environment and continue to pose health risks. On the other hand, the destructive technologies discussed here can effectively destroy PFAS compounds and fully address society's urgent need to remediate this harmful family of chemical compounds. This review reports and compare widely accepted as well as emerging PFAS destruction technologies. Some of the technologies presented in this review are still under development at the lab scale, while others have already been tested in the field.

Non-target and target screening of per- and polyfluoroalkyl substances in landfill leachate and impact on groundwater in Guangzhou, China

Landfills are the main destination of many urban wastes containing per- and polyfluoroalkyl substances (PFAS), and PFAS may leach out from the waste and contaminate the surrounding groundwater. Here we investigated the occurrence of PFAS in leachate and surrounding groundwater from three landfills in Guangzhou, China by using a combined target and non-target approach. Non-target screening showed that a total of 651 PFAS with 96 classes were identified, including 17 legacy PFAS and 637 emerging PFAS. The quantitative target analysis of some PFAS revealed that the average removal rate of PFAS from the raw leachates were ranged between 62 % and 99 %. Statistical analysis and source analysis suggested that landfill leachate was a major source of PFAS in the groundwater within the landfills and downstream sites. The results from the combined target and non-target analyses demonstrated that PFAS in landfills could leach into the surrounding groundwater, and may affect the sustainable use of groundwater as a source of drinking water and pose a potential risk to human health.

Occurrence of per- and polyfluoroalkyl substances (PFAS) in municipal solid waste landfill leachates from western China

Landfill leachate has been documented as a significant source of trace organic pollutants, comprising an expansive family of per- and polyfluoroalkyl substances (PFAS). This study presents the findings on the distribution of 13 perfluoroalkyl carboxylates (PFCAs) and 4 perfluoroalkyl sulfonates (PFSAs) in leachates from 6 municipal solid waste (MSW) landfills in western China. The total concentrations of 17 PFAS in sampled leachates ranged from 1805 to 43,310 ng/L, and 15 compounds were detected in all samples. The short-chain compounds perfluorobutane sulfonate (PFBS, mean mass fraction 23.1%) and perfluorobutyric acid (PFBA, mean mass fraction 20.6%) were dominant. There were higher PFAS concentrations in leachates from operating landfills (mean: 12,194 ng/L) compared to closed landfills (mean: 2747 ng/L), but there was no significant difference between young (< 10 years) and old landfills (> 10 years). Moderate to weak correlations were observed between PFAS concentrations and leachate properties, e.g., TN, NH₄⁺-N, TOC, and pH. This is the first report on the distribution of PFAS in landfill leachates from western China. The results have identified landfill leachate as an underestimated source of PFAS in the environment and have contributed to a more comprehensive evaluation on PFAS presence across China.

Non-target discovery of emerging PFAS homologues in Dagang Oilfield: Multimedia distribution and profiles in crude oil

Per- and polyfluoroalkyl substances (PFASs) are applied in oil exploitation activity. In this study, non-target and suspect target analyses with high-resolution mass spectrometry were used for identification of novel PFASs in the oilfield environment. A total of thirty-seven PFAS homologues belonging to eight classes were identified as level 4 or above, which partly explained the amount of potential unknown PFAS-precursors that were indicated by total oxidisable precursor assay in our previous study. Hydrogen-substituted and ether-substituted homologues were the main identified PFASs, and seven of them were newly reported homologues. C1-C3 perfluoroalkane sulphonic acids (PFSAs) were also for the first time identified in the oilfield. The sediment-water partitioning coefficients of most identified PFAS homologues positively correlate with their predicted octanol-water partitioning coefficients while those of C1-C3 PFSAs may have elevated sediment partitioning potential as also previously observed for ultra-short chain C2-C3 perfluoroalkyl carboxylic acids. The crude oil and sludge samples were further examined with the target and identified PFAS profiles. An annual flux of 10.4 kg/y via oil production was estimated in Dagang Oilfield with 16.6 % not from the target PFASs. This demonstrates that oil exploitation activities can be a significant underlying source of PFASs to the environment.

Do PFAS changes in landfill leachate treatment systems correlate with changes in physical chemical parameters?

Per- and polyfluoroalkyl substances (PFAS) have been found at relatively elevated concentrations in landfill leachates. Some landfill facilities treat physical-chemical parameters of their leachates using on-site leachate treatment systems before discharge. The objective of this study was to evaluate whether changes in physical-chemical parameters of leachate at on-site treatment systems (including bulk measurements, oxygen demanding components, and metals) were associated with concentration changes in PFAS. Leachates were evaluated at 15 on-site treatment facilities which included pond systems, aeration tanks, powdered activated carbon (PAC), sand filtration, reverse osmosis (RO) and combination treatment processes. Results show that most physical-chemical parameters and PFAS were significantly reduced in RO systems (over 90 %). For pond systems, statistically significant correlations (r_s > 0.6, p < 0.05) were observed between ∑₂₆PFAS changes and the changes in pH, alkalinity, ammonia, and some metals. Significant correlations were also found between ∑₈PFAAs precursors changes and specific conductivity (SPC), pH, alkalinity, ammonia, and metals changes. For aeration tank systems, significant correlations (r_s > 0.6, p < 0.05) were observed between ∑₂₆PFAS changes and changes in total dissolved solids and zinc, and between the changes of ∑₈PFAAs precursors and field pH. These correlations are believed to be associated with rainfall dilution and precipitation of calcium carbonate and other metals as leachate is introduced to the atmosphere.

Electrochemical oxidation processes for PFAS removal from contaminated water and wastewater: fundamentals, gaps and opportunities towards practical implementation

Electrochemical oxidation (EO) is emerging as one of the most promising methods for the degradation of recalcitrant per- and poly-fluoroalkyl substances (PFASs) in water and wastewater, as these compounds cannot be effectively treated with conventional bio- or chemical approaches. This review examines the state of the art of EO for PFASs destruction, and comprehensively compares operating parameters and treatment performance indicators for both synthetic and real contaminated water and wastewater media. The evaluation shows the need to use environmentally-relevant media to properly quantify the effectiveness/efficiency of EO for PFASs treatment. Additionally, there is currently a lack of quantification of sorption losses, resulting in a likely over-estimation of process' efficiencies. Furthermore, the majority of experimental results to date indicate that short-chain PFASs are the most challenging and need to be prioritized as environmental regulations become more stringent. Finally, and with a perspective towards practical implementation, several operational strategies are proposed, including processes combining up-concentration followed by EO destruction.

The Phytomanagement of PFAS-Contaminated Land

Globally, several hundred thousand hectares of both agricultural and urban land have become contaminated with per- and polyfluoroalkyl substances (PFAS). PFAS compounds are resistant to degradation and are mobile in soil compared to other common contaminants. Many compounds have KD values (matrix/solution concentration quotients) of <10. PFAS compounds endanger the health of humans and ecosystems by leaching into groundwater, exposure via dust, and, to a lesser extent, through plant uptake. This review aims to determine the feasibility of phytomanagement, the use of plants, and the use of soil conditioners to minimize environmental risk whilst also providing an economic return in the management of PFAS-contaminated land. For most sites, PFAS combinations render phytoextraction, the use of plants to remove PFAS from soil, inviable. In contrast, low Bioaccumulation Coefficients (BAC; plant and soil concentration quotients) timber species or native vegetation may be usefully employed for phytomanagement to limit human/food chain exposure to PFAS. Even with a low BAC, PFAS uptake by crop plants may still exceed food safety standards, and therefore, edible crop plants should be avoided. Despite this limitation, phytomanagement may be the only economically viable option to manage most of this land. Plant species and soil amendments should be chosen with the goal of reducing water flux through the soil, as well as increasing the hydrophobic components in soil that may bind the C-F-dominated tails of PFAS compounds. Soil conditioners such as biochar, with significant hydrophobic components, may mitigate the leaching of PFAS into receiving waters. Future work should focus on the interactions of PFAS with soil microbiota; secondary metabolites such as glomalin may immobilize PFAS in soil.

Municipal solid waste incineration (MSWI) ash co-disposal: Influence on per- and polyfluoroalkyl substances (PFAS) concentration in landfill leachate

Municipal solid waste incineration (MSWI) ash is often managed through co-disposal with unburned wastes in landfills, a practice previously reported to result in enhanced leaching of pollutants (e.g., heavy metals) in landfill leachate. The objective of this study was to evaluate the effect of co-disposed unburned wastes on per- and polyfluoroalkyl substances (PFAS) in MSWI ash landfill leachate. Leachate was collected from four landfills containing MSWI ash, either as a sole waste stream or co-disposed of with sewage sludge and MSW screenings. Samples of ash and unburned materials were collected and assessed separately for leachable PFAS in the laboratory. All samples were analyzed for 26 PFAS. Results showed that greater ash content was associated with lower leachate PFAS concentrations. The pure ash monofill exhibited the lowest PFAS in landfill leachate (290 ng L-1) while the landfill contained a large amount of unburned waste had the highest PFAS (11,000 ng L-1). For laboratory leaching tests, average ∑26PFAS concentration in lab ash leachate (310 ng L-1) was 10 and 24 times lower than observed in lab sewage sludge leachate (3,200 ng L-1) and lab MSW screenings leachate (7,500 ng L-1), respectively. Leachate from the ash-only landfill had ∑26PFAS concentration similar to what was measured in the ash itself. On the contrary, ∑26PFAS concentration in co-disposal landfill leachates were similar to those in PFAS-rich unburned waste itself, regardless of the percentages of landfilled unburned wastes. We hypothesize that leachate generated in co-disposal scenarios preferentially flows through PFAS-rich unburned materials and that biotransformation of precursors enhanced by unburned waste degradation further contributes to higher concentrations of terminal PFAS in ash co-disposal sites. Landfill operators should expect PFAS in leachates to be higher when PFAS-rich unburned wastes are disposed of alongside MSWI ash, even if the unburned fraction is small.

Per- and polyfluoralkyl substances (PFAS) in drinking water system: Target and non-target screening and removal assessment

The massive use and the persistence of per- and polyfluoroalkyl substances (PFAS) have led to their frequent detection in aquatic environments, which may further threaten drinking water safety. So far, our knowledge about the occurrence of PFAS in drinking water system is still very limited. Here we investigated the occurrence and removal of PFAS in a drinking water system using non-target, suspect and target screening strategies. Sampling was performed in three seasons in the drinking water system including a water source, two drinking water treatment plants, and tap water in five households. The results showed detection of 17 homologous series with 51 homologues in non-target screening and 50 potential PFAS detected in suspect screening. Probable structures were proposed for 15 PFAS with high confidence levels (the first three of the five levels), with seven of them being reported for the first time in drinking water system. Semi-quantification was performed on seven homologous series based on target PFAS, the estimated total concentrations for non-target PFAS ranged between 4.10 and 17.6 ng/L. Nine out of 50 target PFAS were found and precisely quantified (<LOQ-13.4 ng/L) with predominance of perfluorocarboxylic acids (PFCA) and perfluorosulfonic acids (PFSA). All target and non-target PFAS were detected in tap water with similar concentrations in all three seasons. Removal efficiency for the detected PFAS in each processing unit was almost zero, indicating the recalcitrance of these chemicals to the conventional treatment process. The findings from this study clearly show the wide presence of PFAS in the whole drinking water treatment process, and suggest an urgent need for effective removal technology for this group of chemicals.

Concentration profiles of per- and polyfluoroalkyl substances in major sources to the environment

A review of published literature was conducted to present the concentrations and composition profiles of per- and polyfluoroalkyl substances (PFAS) from significant sources to the environment. The major sources of PFAS to the environment are categorized under direct and indirect sources. The characteristic compounds and concentrations are summarized as found from direct sources such as manufacturing facilities, aqueous film-forming foam (AFFF) applications, metal coating operations, and textile and paper coating operations; and from indirect sources such as landfills and wastewater treatment plants (WWTPs). The major findings are: 1) among the aqueous matrices for which data were reviewed, groundwater impacted by AFFF contamination showed the highest median concentrations for both perfluorooctanoic acid (PFOA) and perfluorooctane sulfonic acid (PFOS), while the second-highest median concentrations were associated with landfill leachates for PFOA and metal-plating sources for PFOS; 2) many of the unknown polyfluorinated precursors present in AFFF-impacted sites could potentially convert to persistent PFAS by abiotic or biotic transformation, and therefore could act as the long-term source of contamination to the environment; 3) part per billion (ppb) concentrations of PFAS were detected in water bodies surrounding fluorochemical manufacturing plants; 4) in consumer products such as textile, paper, and personal care products, PFOA concentrations were an order of magnitude higher compared to other PFAS; 5) biotransformation products such as fluorotelomer carboxylic acids (FTCAs) and perfluoroalkyl acids (PFAAs) are detected in landfill leachates and WWTP effluents; and 6) many studies have shown increased PFAA concentrations in WWTP effluents compared to influents. This work provides a comprehensive review of the literature on the PFAS concentration and composition trends of select non-polymeric PFAS in different sources.

Perfluoroalkyl substances (PFAS) adsorption in drinking water by granular activated carbon: Influence of activated carbon and PFAS characteristics

Perfluoroalkyl substances (PFAS) persistence in the environment leads to their presence in drinking water, that is of high concern due to their potential human health risk. Adsorption onto activated carbon (AC) has been identified as an effective technique to remove PFAS. Adsorption isotherms and breakthrough curves, determined by rapid small-scale column tests (RSSCTs), were studied for eight PFAS and four granular ACs, characterized by different origins, porosities and numbers of reactivation cycles. Both batch and RSSCT results highlighted the strong interaction of AC and PFAS characteristics in adsorption capacity. The most important factor affecting AC performance is the surface charge: a positively-charged AC showed higher adsorption capacities with greater Freundlich constants (K_F) and later 50% breakthroughs compared to the AC with neutral surface. Among the positively-charged ACs, a microporous AC demonstrated higher adsorption capacities for hydrophilic and marginally hydrophobic PFAS, while the mesoporous AC performed better for more hydrophobic PFAS, possibly due to lower pore blockage by organic matter. These results were confirmed at full-scale through a one-year monitoring campaign, in which samples were collected at the inlets and outlets of GAC systems in 17 drinking water treatment plants spread in a wide urban area, where the four analyzed ACs are used.

Perfluoroalkyl substances (PFASs) in leachate, fly ash, and bottom ash from waste incineration plants: Implications for the environmental release of PFAS

Perfluoroalkyl substances (PFASs) are a family of chemicals widely distributed in daily use consumer products. Most of these products become municipal solid wastes (MSWs) after they have been used. In the present study, we examined different types of PFASs in leachate, fly ash and bottom ash produced from three MSW incineration plants in southern China. High PFAS levels were found in leachate (mean concentration 215 ng/mL, range 21.4-682 ng/mL) from the incineration plants, which indicated large amounts of PFASs in the wastes leached out. The average quantities of PFASs annually discharged from the leachates of the three plants were estimated to be approximately 384 kg (Plant A), 47.3 kg (Plant B), and 2.82 kg (Plant C). Relatively lower levels of PFASs in fly ash (mean 16.4 ng/g, range 1.46-87.6 ng/g) and bottom ash (mean 14.6 ng/g, range 3.11-77.4 ng/g) indicated that high-temperature incineration destroyed most of the PFASs. The wide array of PFASs concentrations in all three matrices illustrated that some PFASs-containing industrial wastes were still entered into local MSW. In general, short chain PFASs, including perfluorobutyric acid (PFBA) and perfluorobutane sulfonate (PFBS), were the primary PFASs in leachate samples. In addition, PFOS was the predominant PFASs in fly ash samples. The results showed that leachate, fly ash, and bottom ash from MSW incineration plants are important vectors of PFASs.

Per and poly-fluoroalkyl substances (PFAS) as a contaminant of emerging concern in surface water: A transboundary review of their occurrences and toxicity effects

Per and poly-fluoroalkyl substances (PFAS) have been recognized as contaminants of emerging concerns by the United States Environmental Protection Agency (US EPA) due to their environmental impact. Several advisory guidelines were proposed worldwide aimed at limiting their occurrences in the aquatic environments, especially for perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA). This review paper aims to provide a holistic review in the emerging area of PFAS research by summarizing the spatiotemporal variations in PFAS concentrations in surface water systems globally, highlighting the possible trends of occurrences of PFAS, and presenting potential human health impacts as a result of PFAS exposure through surface water matrices. From the data analysis in this study, occurrences of PFOA and PFOS in many surface water matrices were observed to be several folds higher than the US EPA health advisory level of 70 ng/L for lifetime exposure from drinking water. Direct discharge and atmospheric deposition were identified as primary sources of PFAS in surface water and cryosphere, respectively. While global efforts focused on limiting usages of long-chain PFAS such as PFOS and PFOA, the practices of using short-chain PFAS such as perfluorobutanoic acid (PFBA) and perfluorobutane sulfonic acid (PFBS) and PFAS alternatives increased substantially. These compounds are also potentially associated with adverse impacts on human health, animals and biota.

Occurrence of per- and polyfluoroalkyl substances and unidentified organofluorine in leachate from waste-to-energy stockpile - A case study

Per- and polyfluoroalkyl substances (PFASs) are a diverse group of chemicals used in consumer products, which will inevitably end up in waste streams. Landfills are widely recognized secondary point sources of PFASs, but other types of waste management sites have received less attention. Therefore, in a case study presented here we investigated releases of PFASs from temporarily stored waste by determining quantities of 34 PFASs in leachate from a Waste-to-Energy stockpile (45 000 ± 2000 tonnes) during five months in 2019. We also measured extractable organofluorine (EOF) to account for PFASs not included in the target list. The mean total concentration of the 34 PFAS (Σ₃₄PFAS) was 211 ± 31 ng/L, and short-chain (C4-C7) perfluorocarboxylic acids (PFCAs) accounted for 56-60% of the total. Moreover, we found that Σ₃₄PFAS only accounted for 12% ± 4% of EOF detected in the leachate. Our results demonstrate that waste stockpiles are previously unexplored sources of PFASs in the environment, and the dominance of short-chain PFCAs is consistent with observed profiles of contaminants in landfill leachates.

Electrochemical degradation of per- and poly-fluoroalkyl substances using boron-doped diamond electrodes

Electrochemical degradation using boron-doped diamond (BDD) electrodes has been proven to be a promising technique for the treatment of water contaminated with per- and poly-fluoroalkyl substances (PFAS). Various studies have demonstrated that the extent of PFAS degradation is influenced by the composition of samples and electrochemical conditions. This study evaluated the significance of several factors, such as the current density, initial concentration of PFAS, concentration of electrolyte, treatment time, and their interactions on the degradation of PFAS. A 2⁴ factorial design was applied to determine the effects of the investigated factors on the degradation of perfluorooctanoic acid (PFOA) and generation of fluoride in spiked water. The best-performing conditions were then applied to the degradation of PFAS in wastewater samples. The results revealed that current density and time were the most important factors for PFOA degradation. In contrast, a high initial concentration of electrolyte had no significant impact on the degradation of PFOA, whereas it decreased the generation of F^-. The experimental design model indicated that the treatment of spiked water under a current density higher than 14 mA cm^-2 for 3-4 h could degrade PFOA with an efficiency of up to 100% and generate an F^- fraction of approximately 40-50%. The observed high PFOA degradation and a low concentration of PFAS degradation products indicated that the mineralization of PFOA was effective. Under the obtained best conditions, the degradation of PFOA in wastewater samples was 44-70%. The degradation efficiency for other PFAS in these samples was 65-80% for perfluorooctane sulfonic acid (PFOS) and 42-52% for 6-2 fluorotelomer sulfonate (6-2 FTSA). The presence of high total organic carbon (TOC) and chloride contents was found to be an important factor affecting the efficiency of PFAS electrochemical degradation in wastewater samples. The current study indicates that the tested method can effectively degrade PFAS in both water and wastewater and suggests that increasing the treatment time is needed to account for the presence of other oxidizable matrices.

A review of the occurrence, transformation, and removal of poly- and perfluoroalkyl substances (PFAS) in wastewater treatment plants

Poly- and perfluoroalkyl substances (PFAS) comprise more than 4,000 anthropogenically manufactured compounds with widescale consumer and industrial applications. This critical review compiles the latest information on the worldwide distribution of PFAS and evaluates their fate in wastewater treatment plants (WWTPs). A large proportion (>30%) of monitoring studies in WWTPs were conducted in China, followed by Europe (30%) and North America (16%), whereas information is generally lacking for other parts of the world, including most of the developing countries. Short and long-chain perfluoroalkyl acids (PFAAs) were widely detected in both the influents (up to 1,000 ng/L) and effluents (15 to >1,500 ng/L) of WWTPs. To date, limited data is available regarding levels of PFAS precursors and ultra-short chain PFAS in WWTPs. Most WWTPs exhibited low removal efficiencies for PFAS, and many studies reported an increase in the levels of PFAAs after wastewater treatment. The analysis of the fate of various classes of PFAS at different wastewater treatment stages (aerobic and/aerobic biodegradation, photodegradation, and chemical degradation) revealed biodegradation as the primary mechanism responsible for the transformation of PFAS precursors to PFAAs in WWTPs. Remediation studies at full scale and laboratory scale suggest advanced processes such as adsorption using ion exchange resins, electrochemical degradation, and nanofiltration are more effective in removing PFAS (~95-100%) than conventional processes. However, the applicability of such treatments for real-world WWTPs faces significant challenges due to the scaling-up requirements, mass-transfer limitations, and management of treatment by-products and wastes. Combining more than one technique for effective removal of PFAS, while addressing limitations of the individual treatments, could be beneficial. Considering environmental concentrations of PFAS, cost-effectiveness, and ease of operation, nanofiltration followed by adsorption using wood-derived biochar and/or activated carbons could be a viable option if introduced to conventional treatment systems. However, the large-scale applicability of the same needs to be further verified.

Legacy and emerging per- and polyfluoroalkyl substances (PFASs) in Dagang Oilfield: Multimedia distribution and contributions of unknown precursors

A systematic survey was conducted on twenty-six per- and polyfluoroalkyl substances (PFASs) in fifty-one paired samples of surface water, sediment, and soil from Dagang Oilfield, Tianjin, China. Perfluorooctanoic acid, perfluorooctane sulfonic acid, p-perfluorous nonenoxybenzenesulfonate (OBS), and 6:2 fluorotelomer sulfonamidoalkyl betaine (6:2 FTAB) were ubiquitous in the oilfield with field log K_d of 1.3-2.2, indicating a high partition potential from surface water to sediment. Total petroleum hydrocarbons (TPH) are a predictor for PFAS contamination at oilfield. The concentrations of OBS and 6:2 FTAB were higher in surface water and sediment with elevated TPH level. With total oxidizable precursor assay, unknown precursors for C2-C3 perfluoroalkyl carboxylic acids (PFCAs) (57-99 mol%) contributed more than those for C4-C12 PFCAs in the three mediums. The unknown C4-, C6-, and C8-based precursors tended to be precursors for perfluoroalkyl sulfonates at the oilfield, and C8 fluorotelomer-based precursors particularly occurred in the surface water. The concentrations of C4- and C8-based precursors were found positively correlated with TPH levels (r = 0.67-0.72, p < 0.05), while C6 precursors may also come from other sources. Further studies are necessary to clarify the mass balance and risk assessment for unknown PFASs.

Treatment of PFAS-containing landfill leachate using an enhanced contact plasma reactor

A bench-scale plasma reactor was used to degrade poly- and perfluoroalkyl substances (PFAS) in landfill leachate samples obtained from three different locations. In the leachate samples before treatment, five long-chain, six short-chain perfluoroalkyl acids (PFAAs) and eight PFAA precursors were detected in a wide concentration range (~10² to 10⁵ ng/L; total oxidizable precursors (TOP) ~10⁶ ng/L). The concentration of perfluorooctane sulfonate (PFOS) plus perfluorooctanoic acid (PFOA) ranged between 2000 and 3000 ng/L. Plasma-based water treatment of 500 mL samples resulted in faster removal rates for longer-chain than shorter chain length PFAAs. Both PFOS and PFOA were removed to below United States Environmental Protection Agency's (USEPA's) health advisory concentration level (HAL) concentrations (<70 ng/L) in 10-75 min; 90% PFOA and PFOS removal was achieved in 10 min. Long-chain and short-chain PFAAs were removed by >99.9% and 10-99.9%, respectively. The removal rate constant (k_PFOA+PFOS) for combined PFOA and PFOS ranged between 0.20 and 0.34 min^-1. Overall, 60 ± 2% of the TOP concentration and 34 ± 2% of the TOC were removed. No effect of non-PFAS co-contaminants (e.g., total initial organic carbon concentration ~2000 mg/L) on the degradation efficiency was observed. Short-chain PFAA removal efficacy was enhanced by adding a cationic surfactant (cetrimonium bromide). Overall, the results indicate that plasma-based technology may be a viable technology for the treatment of PFAS-contaminated landfill leachates.

The fate of poly- and perfluoroalkyl substances in a marine food web influenced by land-based sources in the Norwegian Arctic

Although poly- and perfluorinated alkyl substances (PFAS) are ubiquitous in the Arctic, their sources and fate in Arctic marine environments remain unclear. Herein, abiotic media (water, snow, and sediment) and biotic media (plankton, benthic organisms, fish, crab, and glaucous gull) were sampled to study PFAS uptake and fate in the marine food web of an Arctic Fjord in the vicinity of Longyearbyen (Svalbard, Norwegian Arctic). Samples were collected from locations impacted by a firefighting training site (FFTS) and a landfill as well as from a reference site. Mean concentration in the landfill leachate was 643 ± 84 ng L^-1, while it was 365 ± 8.0 ng L^-1 in a freshwater pond and 57 ± 4.0 ng L^-1 in a creek in the vicinity of the FFTS. These levels were an order of magnitude higher than in coastal seawater of the nearby fjord (maximum level , at the FFTS impacted site). PFOS was the most predominant compound in all seawater samples and in freshly fallen snow (63-93% of ). In freshwater samples from the Longyear river and the reference site, PFCA ≤ C₉ were the predominant PFAS (37-59%), indicating that both local point sources and diffuse sources contributed to the exposure of the marine food web in the fjord. concentrations increased from zooplankton (1.1 ± 0.32 μg kg^-1 ww) to polychaete (2.8 ± 0.80 μg kg^-1 ww), crab (2.9 ± 0.70 μg kg^-1 ww whole-body), fish liver (5.4 ± 0.87 μg kg^-1 ww), and gull liver (62.2 ± 11.2 μg kg^-1). PFAS profiles changed with increasing trophic level from a large contribution of 6:2 FTS, FOSA and long-chained PFCA in zooplankton and polychaetes to being dominated by linear PFOS in fish and gull liver. The PFOS isomer profile (branched versus linear) in the active FFTS and landfill was similar to historical ECF PFOS. A similar isomer profile was observed in seawater, indicating major contribution from local sources. However, a PFOS isomer profile enriched by the linear isomer was observed in other media (sediment and biota). Substitutes for PFOS, namely 6:2 FTS and PFBS, showed bioaccumulation potential in marine invertebrates. However, these compounds were not found in organisms at higher trophic levels.

Evaluation of extraction workflows for quantitative analysis of per- and polyfluoroalkyl substances: A case study using soil adjacent to a landfill

Specific aspects of previously reported extraction workflows, for measurement of per- and polyfluoroalkyl substances (PFAS) in solid matrices, have not been adequately interrogated. The objective of this study was to explore the importance of each workflow step in providing the most appropriate extraction for a comprehensive set of PFAS (51 different species) in soil. We compared different procedures, including two pre-extraction set ups (overnight handling of samples prior to extraction), two extraction solvents (methanol (MeOH), and acetonitrile (ACN)), two extraction solvent volumes (10 mL and 8.5 mL), and two post-extraction cleanup strategies (ENVI-Carb and ion-pair). Of the 51 species targeted, 21 were at quantifiable levels in soil samples collected adjacent to a landfill, of which 13 PFAS were consistently detected among the different extraction workflows. Overall, results showed no significant difference in PFAS concentration between different extraction solvents and cleanup strategies. Perfluoropentanoic acid, perfluorohexanoic acid, and perfluorooctanoic acid had the highest concentrations in all extraction workflows, accounting for nearly 13%, 38%, and 17% of the total monitored PFAS (ΣPFAS), respectively. While final concentration values were similar across methods, recovery and accuracy studies showed that MeOH had the best recovery, with 88% of the isotopically labeled PFAS standards showing extraction recovery within the acceptable range of 80% to 120% (compared to 14% of isotopically labeled PFAS standards in workflows using ACN). Upon examination of additional cleanup steps, 67% of monitored PFAS (out of 51 total PFAS monitored), on average, exhibited higher accuracy (relative error ≤20%) using ENVI-Carb clean up (in comparison with 51% in workflows using ion pair clean up). Results also demonstrated that larger volumes of MeOH (and subsequent re-extractions) did not yield a better recovery, enabling a reduction in overall analysis time and cost in comparison to many published methods.

Electrochemical oxidation of PFOA and PFOS in landfill leachates at low and highly boron-doped diamond electrodes

Polyfluorinated alkyl substances (PFASs) may reach landfill leachates (LLs) due to improper waste management. In this study perfluorooctanoate (PFOA) and perfluorooctane sulphonate (PFOS) were used as representatives of PFASs in the decomposition on boron-doped diamond electrodes (BDDs) with high (10k ppm) and low (0.5k ppm) boron doping concentrations. The result shows that although better COD removal efficacies are obtained on the low-doped BDD (59 % after 8 h), the decomposition rate of PFOA and PFOS was not affected by boron doping. In LLs, at the current density of 75 mA/cm², averaged removal efficiencies of 80 % and 78 % were achieved for PFOA and PFOS, respectively. But besides concentration of mother compounds, the presence of intermediates during electrolysis should be monitored. After 8 h of LL electrolysis, the presence of long-chain degradates C₆F₁₃ and C₆F₁₃COO^- was still observed only in 10k BDD-PFOA assays, while during 0.5k assays C₆F₁₃ and C₆F₁₃COO^- form more intesively at the beginning of the process. This indirectly confirms the more intensive generation of perfluoroalkoxy and hydroxyl radicals and higher susceptibility to electrolysis of PFOA's long-chain intermediates on 0.5k BDD. This is the first study reporting BDD-electrolysis as promising in PFAS removal from the complex matrix of LLs, despite the oxidation of competing LLs components.

Exploring indirect photolysis of 6:2 fluorotelomer sulfonate in landfill leachate under simulated sunlight: effect of humic acid and nitrate

Landfill leachate is exposed to sunlight through on- and off-site leachate treatment and disposal to surface water bodies. Very little is known about the potential phototransformation of fluorotelomer compounds in landfill leachates, which can undergo environmental oxidation and produce perfluorocarboxylic acids (PFCAs). This study investigated phototransformation of spiked 6:2 fluorotelomer sulfonate (FTS) (∼ 100 μg/L) in leachate under simulated sunlight, using a metal halide lamp (wavelength, 390 to 750 nm). To understand the effects of nitrate and humic acid (HA), phosphate buffer (pH 7.1) containing nitrate and HA were spiked with 6:2 FTS and irradiated under simulated sunlight for 72 h. Following irradiation, 6:2 FTS and known transformation products (i.e., PFCAs) were quantified in the samples using LC-MS/MS. The results showed that 6:2 FTS was undergoing indirect photolysis in leachate (half-life of ∼ 15 days), suggesting that indirect photolysis of 6:2 FTS is likely a relevant transformation pathway in sunlit aquatic environments. However, the spiked 6:2 FTS did not show any observable decrease in the presence of nitrate and HA over 72 h. Perfluorohexanoic acid (PFHxA) increased in irradiated leachate background samples (without 6:2 FTS spike) suggesting that phototransformation in sunlit leachate could lead to the formation of persistent PFCAs at environmental concentrations of the precursors. Future studies using probe compounds are recommended to better understand the roles of reactive species in phototransformation of 6:2 FTS.

Legacy and emerging per- and polyfluoroalkyl substances (PFASs) in multi-media around a landfill in China: Implications for the usage of PFASs alternatives

To date, per- and polyfluoroalkyl substances (PFASs) in environmental media surrounding landfills have not attracted much attention. In this study, six legacy PFASs, six short-chain analogues and five emerging alternatives were investigated in groundwater, surface water and sediment samples taken in the vicinity of a valley-type landfill, which had been in operation for over 20 years. Total PFAS concentrations of 110-236 ng/L, 17.3-163 ng/L and 7.91-164 ng/g dw were detected in the surface water, groundwater and sediment samples, respectively. Overall, perfluorooctanoic acid (PFOA) was the dominant PFAS in surface water, but elevated concentrations of perfluorobutanoic acid (PFBA) and perfluoropentanoic acid (PFPeA) were detected in the surface water samples taken adjacent to the landfill, suggesting that the landfill contributed to these compounds. PFBA was the dominant PFAS in the groundwater and sediments. The concentrations of long-chain perfluoroalkyl carboxylic acids (PFCAs) (C8-C12) in the sediment samples correlated significantly with the TOC, Al₂O₃ and Fe₂O₃ contents. The partitioning behaviors of PFCAs in the water-sediment system varied depending on the CF₂ moiety units. For the long-chain PFCAs, positive correlations between the average LogK_d and the number of CF₂ moieties were found to be statistically significant, whereas negative correlations were observed for the short-chain PFCAs (C4-C7). The ratios of short-chain analogues and emerging alternatives versus their respective legacy PFOA and perfluorooctane sulfonate (PFOS) in surface water suggested an increasing trend of short-chain analogues, such as PFBA. The potential health risks of PFOS and PFOA, determined by calculating the estimated daily intake (EDI), were found to be negligible via the drinking groundwater exposure pathway, but more comprehensive studies on the human health risks of PFASs from landfills are essential.

Emerging pharmaceuticals and industrial chemicals in Nakdong River, Korea: Identification, quantitative monitoring, and prioritization

The extensive development and use of new anthropogenic chemicals have inevitably led to their presence in aquatic environments. Surface waters affected by sewage effluents have been exposed to these new substances. In the present study, the occurrence of anthropogenic substances, including pharmaceuticals and industrial chemicals, was investigated in one of the major rivers in Korea, the Nakdong River. Furthermore, seasonal variations in their content were determined via annual monitoring. Through the suspect and non-target screening (SNTS) technique, 58 substances were newly identified in the river and integrated in the quantitative monitoring practice. The results revealed that niflumic acid and melamine exhibited the highest median concentrations, i.e., 320 ng/L and 11,000 ng/L, respectively. The results associated with seasonal change revealed that the concentration of a considerable number of substances increased in winter when the flow rate was low. Conversely, some substances exhibited high concentrations in summer (e.g., polyethylene glycol) and spring (e.g., niflumic acid). This was attributed to the seasonal changes in the consumption, prescriptions, or the application of alternative substances. These changes were also reflected by the risk quotient (RQ) values calculated from the concentration and toxicity values. Pharmaceuticals such as telmisartan and carbamazepine and industrial chemicals such as organophosphorus flame retardants (OPFRs) and melamine accounted for approximately 90% of the total RQ. Major substances prioritized using the production of the RQ value and the detection frequency included OPFRs and telmisartan. It is recommended that these results be reflected in future water quality monitoring plans.

From Waste Collection Vehicles to Landfills: Indication of Per- and Polyfluoroalkyl Substance (PFAS) Transformation

Municipal solid waste contain diverse and significant amounts of per- and polyfluoroalkyl substances (PFAS), and these compounds may transform throughout the "landfilling" process from transport through landfill degradation. Fresh vehicle leachates, from commercial and residential waste collection vehicles at a transfer station, were measured for 51 PFAS. Results were compared to PFAS levels obtained from aged landfill leachate at the disposal facility. The landfill leachate was dominated by perfluoroalkyl acids (PFAAs, including perfluoroalkyl carboxylic acids (PFCAs) and perfluoroalkyl sulfonic acids (PFSAs); 86% of the total PFAS, by median mass concentration), while the majority of PFAS present in commercial and residential waste vehicle leachate were PFAA-precursors (70% and 56% of the total PFAS, by median mass concentration, respectively), suggesting precursor transformation to PFAAs during the course of landfill disposal. In addition, several PFAS, which are not routinely monitored-perfluoropropane sulfonic acid (PFPrS), 8-chloro-perfluoro-1-octane sulfonic acid (8Cl-PFOS), chlorinated polyfluoroether sulfonic acids (6:2, 8:2 Cl-PFESAs), sodium dodecafluoro-3H-4,8-dioxanonanoate (NaDONA), and perfluoro-4-ethylcyclohexanesulfonate (PFECHS)-were detected. Potential degradation pathways were proposed based on published studies: transformation of polyfluoroalkyl phosphate diester (diPAPs) and fluorotelomer sulfonic acids (FTS) to form PFCAs via formation of intermediate products such as fluorotelomer carboxylic acids (FTCAs).

An Overview of Per- and Polyfluoroalkyl Substances (PFAS) in the Environment: Source, Fate, Risk and Regulations

The current article reviews the state of art of the perfluoroalkyl and polyfluoroalkyl substances (PFASs) compounds and provides an overview of PFASs occurrence in the environment, wildlife, and humans. This study reviews the issues concerning PFASs exposure and potential risks generated with a focus on PFAS occurrence and transformation in various media, discusses their physicochemical characterization and treatment technologies, before discussing the potential human exposure routes. The various toxicological impacts to human health are also discussed. The article pays particular attention to the complexity and challenging issue of regulating PFAS compounds due to the arising uncertainty and lack of epidemiological evidence encountered. The variation in PFAS regulatory values across the globe can be easily addressed due to the influence of multiple scientific, technical, and social factors. The varied toxicology and the insufficient definition of PFAS exposure rate are among the main factors contributing to this discrepancy. The lack of proven standard approaches for examining PFAS in surface water, groundwater, wastewater, or solids adds more technical complexity. Although it is agreed that PFASs pose potential health risks in various media, the link between the extent of PFAS exposure and the significance of PFAS risk remain among the evolving research areas. There is a growing need to address the correlation between the frequency and the likelihood of human exposure to PFAS and the possible health risks encountered. Although USEPA (United States Environmental Protection Agency) recommends the 70 ng/L lifetime health advisory in drinking water for both perfluorooctane sulfonate (PFO) perfluorooctanoic acid (PFOA), which is similar to the Australian regulations, the German Ministry of Health proposed a health-based guidance of maximum of 300 ng/L for the combination of PFOA and PFOS. Moreover, there are significant discrepancies among the US states where the water guideline levels for the different states ranged from 13 to 1000 ng L−1 for PFOA and/or PFOS. The current review highlighted the significance of the future research required to fill in the knowledge gap in PFAS toxicology and to better understand this through real field data and long-term monitoring programs.