Emerging organic contaminants in wastewater: Understanding electrochemical reactors for triclosan and its by-products degradation

Fluorine-functionalized covalent organic framework coated solid-phase microextraction probe coupled with electrospray ionization mass spectrometry for monitoring triclosan, triclocarban, and chlorophenols in mice

Triclosan (TCS), triclocarban (TCC), and chlorophenols (CPs) are broad-spectrum antibacterials widely used in dermatological and oral hygiene products, which could induce severe liver and intestine injuries. Hence, it is essential to establish a rapid and sensitive method to monitor TCS, TCC, and CPs in various organisms. In this work, fluorine-functionalized covalent organic framework (COF-F) was prepared by using 4,4',4''-(1,3,5-triazine-2,4,6-triyl)tri-aniline and 2,3,5,6-tetrafluoroterephthalaldehyde as two building units and employed as a solid phase microextraction (SPME) probe for the extraction of TCS, TCC and CPs. The COF-F possessed excellent hydrophobicity, a large specific surface area (1354.3 m2 g-1) and high uniform porosity (3.2 nm), which facilitated high selectivity and adsorption properties towards TCS, TCC, and CPs. Therefore, the as-prepared COF-F-SPME in combination with electrospray ionization mass spectrometry has been developed to provide fast and ultrasensitive detection of TCS, TCC, and CPs in biological samples. The established method demonstrated satisfactory linear ranges (0.01-100.00 μg L-1) and low limits of detection (0.003-0.040 μg L-1) for TCS, TCC and CPs. The developed method could be successfully applied to detect TCS, TCC and CPs in the liver and kidney tissues of mice, demonstrating the potential for the detection of chlorinated aromatic pollutants in the biological samples.

Impact and migration behavior of triclosan on waste-activated sludge anaerobic digestion

Triclosan (TCS), a hydrophobic antibacterial agent, is extensive application in daily life. Despite a low biodegradability rate, its hydrophobicity results in its accumulation in waste-activated sludge (WAS) during domestic and industrial wastewater treatment. While anaerobic digestion is the foremost strategy for WAS treatment, limited research has explored the interphase migration behavior and impacts of TCS on WAS degradation during anaerobic digestion. This study revealed TCS migration between solid- and liquid-phase in WAS digestion. The solid-liquid distribution coefficients of TCS were negative for proteins and polysaccharides and positive for ammonium. High TCS levels promoted volatile-fatty-acid accumulation and reduced methane production. Enzyme activity tests and functional prediction indicated that TCS increased enzyme activity associated with acid production, in contrast to the inhibition of key methanogenic enzymes. The findings of the TCS migration behavior and its impacts on WAS anaerobic digestion provide an in-depth understanding of the evolution of enhanced TCS-removing technology.

Status and future trends in wastewater management strategies using artificial intelligence and machine learning techniques

The two main things needed to fulfill the world's impending need for water in the face of the widespread water crisis are collecting water and recycling. To do this, the present study has placed a greater focus on water management strategies used in a variety of contexts areas. To distribute water effectively, save it, and satisfy water quality requirements for a variety of uses, it is imperative to apply intelligent water management mechanisms while keeping in mind the population density index. The present review unveiled the latest trends in water and wastewater recycling, utilizing several Artificial Intelligence (AI) and machine learning (ML) techniques for distribution, rainfall collection, and control of irrigation models. The data collected for these purposes are unique and comes in different forms. An efficient water management system could be developed with the use of AI, Deep Learning (DL), and the Internet of Things (IoT) structure. This study has investigated several water management methodologies using AI, DL and IoT with case studies and sample statistical assessment, to provide an efficient framework for water management.

Unveiling microbial degradation of triclosan: Degradation mechanism, pathways, and catalyzing clean energy

Emerging organic contaminants present in the environment can be biodegraded in anodic biofilms of microbial fuel cells (MFCs). However, there is a notable gap existing in deducing the degradation mechanism, intermediate products, and the microbial communities involved in degradation of broad-spectrum antibiotic such as triclosan (TCS). Herein, the possible degradation of TCS is explored using TCS acclimatized biofilms in MFCs. 95% of 5 mgL-1 TCS are been biodegraded within 84 h with a chemical oxygen demand (COD) reduction of 62% in an acclimatized-MFC (A-MFC). The degradation of TCS resulted in 8 intermediate products including 2,4 -dichlorophenol which gets further mineralized within the system. Concurrently, the 16S rRNA V3-V4 sequencing revealed that there is a large shift in microbial communities after TCS acclimatization and MFC operation. Moreover, 30 dominant bacterial species (relative intensity >1%) are identified in the biofilm in which Sulfuricurvum kujiense, Halomonas phosphatis, Proteiniphilum acetatigens, and Azoarcus indigens significantly contribute to dihydroxylation, ring cleavage and dechlorination of TCS. Additionally, the MFC was able to produce 818 ± 20 mV voltage output with a maximum power density of 766.44 mWm-2. The antibacterial activity tests revealed that the biotoxicity of TCS drastically reduced in the MFC effluent, signifying the non-toxic nature of the degraded products. Hence, this work provides a proof-of-concept strategy for sustainable mitigation of TCS in wastewaters with enhanced bioelectricity generation.

A systematic review of industrial wastewater management: Evaluating challenges and enablers

The study provides a systematic literature review (SLR) encompassing industrial wastewater management research from the past decade, examining enablers, challenges, and prevailing practices. Originating from manufacturing, energy production, and diverse industrial processes, industrial wastewater's handling is critical due to its potential to impact the environment and public health. The research aims to comprehend the current state of industrial wastewater management, pinpoint gaps, and outline future research prospects. The SLR methodology involves scouring the Scopus database, yielding an initial pool of 253 articles. Refinement via search code leaves 101 articles, followed by abstract screening that reduces articles to 79, and finally 66 well-focused articles left for thorough full-text examination. Results underscore the significance of regulatory frameworks, technological innovation, and sustainability considerations as cornerstones for effective wastewater management. However, substantial impediments like; inadequate infrastructure, resource constraints and the necessity for stakeholder collaboration still exist. The study highlights emerging research domains, exemplified by advanced technologies like nanotechnology and bioremediation, alongside the pivotal role of circular economy principles in wastewater management. The SLR offers an exhaustive view of contemporary industrial wastewater management, accentuating the imperative of an all-encompassing approach that integrates regulatory, technological, and sustainability facets. Notably, the research identifies gaps and opportunities for forthcoming exploration, advocating for interdisciplinary research and intensified stakeholder collaboration. The study's insights cater to policymakers, practitioners, and researchers, equipping them to address the challenges and capitalize on prospects in industrial wastewater management effectively.

Role of the hydrolytic-acidogenic phase on the removal of bisphenol A and sildenafil during anaerobic treatment

This paper presents the main results of the removal of two pharmaceutical and personal care products (PPCPs), bisphenol A (BPA) and sildenafil (SDF), by applying anaerobic biological batch tests. The biomass used was previously acclimatized and the experiment lasted 28 days. The effect of factors such as compound (BPA and SDF), concentration and type of inoculum was assessed, considering the factorial experimental design. The results indicated that evaluated factors did not significantly affect the PPCPs elimination in the evaluated range with a confidence level of 95%. On the other hand, the removal percentages obtained with BPA were mainly related to mechanisms, such as sorption and abiotic reactions. Regarding SDF, biodegradation was the predominant mechanism of removal under the experimental conditions of this study; however, the degradation of SDF was partial, with percentages lower than 43% in the tests with hydrolytic/acidogenic inoculum (H/A) and lower than 41% in the tests with methanogenic inoculum (MET). Finally, these findings indicated that hydrolysis/acidogenesis phase is a main contributor to SDF biodegradation in anaerobic digestion. The study provides a starting point for future research that seeks to improve treatment systems to optimize the removal of pollutants from different water sources.

Sustainable application of electrocatalytic and photo-electrocatalytic oxidation systems for water and wastewater treatment: a review

Wastewater treatment and reuse have risen as a solution to the water crisis plaguing the world. Global warming-induced climate change, population explosion and fast depletion of groundwater resources are going to exacerbate the present global water problems for the forthcoming future. In this scenario, advanced electrochemical oxidation process (EAOP) utilising electrocatalytic (EC) and photoelectrocatalytic (PEC) technologies have caught hold of the interest of the scientific community. The interest stems from the global water management plans to scale down centralised water and wastewater treatment systems to decentralised and semicentralised treatment systems for better usage efficiency and less resource wastage. In an age of rising water pollution caused by contaminants of emerging concern (CECs), EC and PEC systems were found to be capable of optimal mineralisation of these pollutants rendering them environmentally benign. The present review treads into the conventional electrochemical treatment systems to identify their drawbacks and analyses the scope of the EC and PEC to mitigate them. Probable electrode materials, potential catalysts and optimal operational conditions for such applications were also examined. The review also discusses the possible retrospective application of EC and PEC as point-of-use and point-of-entry treatment systems during the transition from conventional centralised systems to decentralised and semi-centralised water and wastewater treatment systems.

Tris-Copper Nanozyme as a Novel Laccase Mimic for the Detection and Degradation of Phenolic Compounds

Phenolic compounds are one of the main organic pollutants in the environment that can seriously affect ecosystems, even at very low concentrations. Due to the resistance of phenolic compounds to microorganisms, conventional biological treatment methods face challenges in effectively addressing this pollution problem. In this study, a novel laccase mimic (Tris-Cu nanozyme) is prepared using a simple and rapid synthesis strategy based on the coordination of copper ions and amino groups in Tris(hydroxymethyl)aminomethane (Tris). It is found that the Tris-Cu nanozyme exhibits good catalytic activity against a variety of phenolic compounds, the Km, Vmax and Kcat are determined to be 0.18 mM, 15.62 μM·min-1 and 1.57 × 107 min-1 using 2,4-dichlorophenol (2,4-DP) as the substrate, respectively. Then, based on the laccase-like activity of the Tris-Cu nanozyme, a novel colorimetric method for 2,4-DP (the limit of detection (LOD) = 2.4 μM, S/N = 3) detection in the range of 10-400 μM was established, and its accuracy was verified by analyzing tap and lake water samples. In addition, the Tris-Cu nanozyme shows excellent removal abilities for six phenolic compounds in experiments. The removal percentages for 2,4-DP, 2-chlorophenol (2-CP), phenol, resorcinol, 2,6-dimethoxyphenol (2,6-DOP), and bisphenol A (BPA) are 100%, 100%, 100%, 100%, 87%, and 81% at 1 h, respectively. In the simulated effluent, the Tris-Cu nanozyme maintains its efficient catalytic activity towards 2,4-DP, with a degradation percentage of 76.36% at 7 min and a reaction rate constant (k0) of 0.2304 min-1. Therefore, this metal-organic complex shows promise for applications in the monitoring and degrading of environmental pollutants.

Application of Electrochemical Oxidation for Water and Wastewater Treatment: An Overview

In recent years, the discharge of various emerging pollutants, chemicals, and dyes in water and wastewater has represented one of the prominent human problems. Since water pollution is directly related to human health, highly resistant and emerging compounds in aquatic environments will pose many potential risks to the health of all living beings. Therefore, water pollution is a very acute problem that has constantly increased in recent years with the expansion of various industries. Consequently, choosing efficient and innovative wastewater treatment methods to remove contaminants is crucial. Among advanced oxidation processes, electrochemical oxidation (EO) is the most common and effective method for removing persistent pollutants from municipal and industrial wastewater. However, despite the great progress in using EO to treat real wastewater, there are still many gaps. This is due to the lack of comprehensive information on the operating parameters which affect the process and its operating costs. In this paper, among various scientific articles, the impact of operational parameters on the EO performances, a comparison between different electrochemical reactor configurations, and a report on general mechanisms of electrochemical oxidation of organic pollutants have been reported. Moreover, an evaluation of cost analysis and energy consumption requirements have also been discussed. Finally, the combination process between EO and photocatalysis (PC), called photoelectrocatalysis (PEC), has been discussed and reviewed briefly. This article shows that there is a direct relationship between important operating parameters with the amount of costs and the final removal efficiency of emerging pollutants. Optimal operating conditions can be achieved by paying special attention to reactor design, which can lead to higher efficiency and more efficient treatment. The rapid development of EO for removing emerging pollutants from impacted water and its combination with other green methods can result in more efficient approaches to face the pressing water pollution challenge. PEC proved to be a promising pollutants degradation technology, in which renewable energy sources can be adopted as a primer to perform an environmentally friendly water treatment.

Sustainability assessment of wastewater reuse in a Portuguese military airbase

The current water-scarcity crisis that is being felt in Europe, namely in the southern region, has leveraged the development and implementation of national and regional water management plans. These policies aim to promote efficient wastewater reuse in industrial and urban sectors. Thus, stakeholders are now seeking strategies to enhance the sustainability of their wastewater treatment processes. The present work details the evaluation of the wastewater treatment methods used at an Air Force Base located in Portugal. In addition, this study also intended to determine how wastewater reuse can be implemented and add value to the environmental protection mission of the military airbase. Hence, an assessment of wastewater treatment practices was carried out, considering primary and secondary treatments. The chemical, physical, and biological indicators of samples collected over two consecutive years were analyzed to determine trends and fluctuations. The results revealed that the overall effectiveness of nutrient removal is low due to the oversized nature of the treatment plant, the age of the facility, and the composition of the wastewater. The effluent produced meets standards for non-potable reuse and could be used on base for aircraft maintenance and the cleaning of facilities. Nonetheless, the effectiveness of the plant could be improved by implementing a more advanced tertiary wastewater treatment to decrease the concentration of undesired compounds (e.g., total nitrogen), enabling the reuse of water in a broader range of activities.

Transport of emerging organic ultraviolet (UV) filters in ceramic membranes: Role of polyethylene (PE) microplastics

Microplastics can be considered potential carriers of emerging organic ultraviolet (UV) filters due to their considerable adsorption capacity in wastewater treatment. The adsorption behavior of organic UV filters, which are commonly contained in personal care products to preserve the skin against UV radiation, onto polyethylene (PE) microplastics were systematically studied to investigate their combined effects. Kinetics and isotherm analyses revealed that the adsorption of four organic UV filters onto PE microplastic surfaces followed a multi-rate and a heterogeneous multi-layer pattern. Several factors including salinity, microplastic size, and dosage also influenced the adsorption efficiency due to hydrophobic interactions. A bench-scale cross-flow ceramic membrane filtration experiment was investigated to evaluate the role of PE microplastics on the retention performance of organic UV filters. The retentions for organic UV filters were 34.2%-37.8% in the non-existence of PE microplastics. Conversely, organic UV filter retentions were significantly increased up to 82.2%-97.9% when they were adsorbed onto the PE microplastics, which were almost completely retained by the ceramic membrane. Therefore, organic UV filters can likely migrate and eventually be carried by PE microplastics, thus increasing the retention of both emerging organic UV filters and microplastics prior to discharge from wastewater treatment facilities.

Alternative methods of monitoring emerging contaminants in water: a review

Anthropogenic activities have steadily increased the release of emerging contaminants (ECs) in aquatic bodies, and these ECs may have adverse effects on humans even at their trace (μg L^-1) levels. Their occurrence in wastewater systems is more common, and the current wastewater treatment facilities are inefficient in eliminating many of such persistent ECs. "Gold standard" techniques such as chromatography, mass spectrometry, and other high-resolution mass spectrometers are used for the quantification of ECs of various kinds, but they all have significant limitations. This paper reviews the alternative methods for EC detection, which include voltammetry, potentiometry, amperometry, electrochemical impedance spectroscopy (EIS) based electrochemical methods, colorimetry, surface-enhanced Raman spectroscopy (SERS), fluorescence probes, and fluorescence spectroscopy-based optical techniques. These alternative techniques have several advantages over conventional techniques, including low sample volume, excludes solid phase extraction procedure, high sensitivity, selectivity, portability, reproducibility, rapidity, low cost, and the ability to monitor ECs in real time. This review summarises each of the alternative methods for detecting ECs in water samples and their respective limits of detection (LODs). The sensitivity of each technique varied depending on the type of EC measured, type of electrochemical probe and electrode, substrates, type of nanoparticle (NP), the physicochemical parameters of water samples tested, and more. Nevertheless, this paper also focuses on some of the current challenges encountered by these alternative methods in monitoring ECs.

Understanding the effects of sludge characteristics on the biosorption of triclosan

On account of hydrophobic nature, the adsorption process on solids is considered as the major pathway for triclosan (TCS) removal in wastewater treatment plants. In this work, four sludge sources (primary sludge, thickened sludge, dewatered sludge, and anaerobic digested sludge) were collected to evaluate the adsorption performance of TCS. The solid-liquid distribution coefficients of TCS were increased with total solids increasing of primary sludge, thickened sludge, and dewatered sludge, whereas decreased in anaerobic digested sludge. Results further revealed differences in sludge floc sub-structures of TCS adsorption. The residues contained most of adsorbed TCS in all sub-structures, while distinguished in various extracellular polymeric substances (EPS). The major contributor of EPS sub-fractions to TCS adsorption was identified as tightly bound EPS in thickened sludge and soluble EPS in anaerobic digested sludge. Based on the excitation-emission matrix spectra and Fourier infrared spectrum results, the protein-like and humic acid-like substances were closely related to the TCS adsorption, and hydrogen bond, hydrophobic interaction, and electrostatic interaction were considered as the dominant mechanisms. This study comprehensively reveals the effects of sludge sources and sub-structures on TCS adsorption, which improves the understanding of interaction and migration processes between TCS and sludge.

A state of the art review on electrochemical technique for the remediation of pharmaceuticals containing wastewater

Pharmaceutical wastewater is a frequent kind of wastewater with high quantities of organic pollutants, although little research has been done in the area. Pharmaceutical wastewaters containing antibiotics and high salinity may impair traditional biological treatment, resulting in the propagation of antibiotic resistance genes. The potential for advanced oxidation processes (AOPs) to break down hazardous substances instead of present techniques that essentially transfer contaminants from wastewater to sludge, a membrane filter, or an adsorbent has attracted interest. Among a variety of AOPs, electrochemical systems are a feasible choice for treating pharmaceutical wastewater. Many electrochemical approaches exist now to remediate rivers polluted by refractory organic contaminants, like pharmaceutical micro-pollutants, which have become a severe environmental problem. The first part of this investigation provides the bibliometric analysis of the title search from 1970 to 2021 for keywords such as wastewater and electrochemical. We have provided information on relations between keywords, countries, and journals based on three fields plot, inter-country co-authorship network analysis, and co-occurrence network visualization. The second part introduces electrochemical water treatment approaches customized to these very distinct discarded flows, containing how processes, electrode materials, and operating conditions influence the results (with selective highlighting cathode reduction and anodic oxidation). This section looks at how electrochemistry may be utilized with typical treatment approaches to improve the integrated system's overall efficiency. We discuss how electrochemical cells might be beneficial and what compromises to consider when putting them into practice. We wrap up our analysis with a discussion of known technical obstacles and suggestions for further research.

Wastewater treatment and emerging contaminants: Bibliometric analysis

In recent years, emerging contaminants have been found in the wastewater, surface water, and even drinking water, which should be treated to ensure the safety of our living environment. In this study, we provide a comprehensive summary of wastewater treatment and emerging contaminants research from 1998 to 2021 by using the bibliometric analysis. This study is conducted based on the Web of Science Core Collection Database. The bibliometix R-package, VOSviewer and CiteSpace software are used for bibliometric analysis and science mapping. A dataset of 10, 605 publications has been retrieved. The analysis results show that China has produced the most publications. China and the United States have the closest cooperation. Analysis of the most cited papers reveals that the purification or removal techniques such as ozonation or membrane filtration can effectively remove pharmaceutical compounds from the water environment. We also found that the efficient detection of emerging contaminants and the optimization of removal methods are current challenges. Finally, future research directions are discussed.

Remediation of pharmaceuticals from contaminated water by molecularly imprinted polymers: a review

The release of pharmaceuticals into the environment induces adverse effects on the metabolism of humans and other living species, calling for advanced remediation methods. Conventional removal methods are often non-selective and cause secondary contamination. These issues may be partly solved by the use of recently-developped adsorbents such as molecularly imprinted polymers. Here we review the synthesis and application of molecularly imprinted polymers for removing pharmaceuticals in water. Molecularly imprinted polymers are synthesized via several multiple-step polymerization methods. Molecularly imprinted polymers are potent adsorbents at the laboratory scale, yet their efficiency is limited by template leakage and polymer quality. Adsorption performance of multi-templated molecularly imprinted polymers depends on the design of wastewater treatment plants, pharmaceutical consumption patterns and the population serviced by these wastewater treatment plants.

Novel semi-automated graphene nanosheets based pipette-tip assisted micro-solid phase extraction as eco-friendly technique for the rapid detection of emerging environmental pollutant in waters

In this work, a new semi-automated syringe infusion-pump assisted graphene nanosheets (GNSs) based pipette-tip micro-solid phase extraction (PT-μSPE) as a green sample preparation technique was demonstrated for the sensitive analysis of emerging environmental pollutant in environmental waters using HPLC-UV. Microwave-assisted synthesized GNSs powder was packed into a 100 μL pipette-tip (as PT-μSPE cartridge) connected with a commercial plastic syringe (contains water sample). This setup was attached to a programmable auto-syringe infusion pump for the GNSs-PT-μSPE process. Triclosan (TCS) is an emerging environmental pollutant chosen as a target analyte to examine the extraction capacity and feasibility of GNSs as a sorbent material for PT-μSPE. Parameters affecting the extraction capability were systematically evaluated and thoroughly optimized. At optimized experimental parameters, excellent linearity (r² = 0.9979) was achieved over the concentration range of 2-250 ng mL^-1 for TCS, with a detection limit of 0.5 ng mL^-1. Applicability of the presented method was examined with real water samples, and extraction recoveries obtained were ranged between 94.6-102.4% with RSD less than 7.8%. The presented protocol is a simple, semi-automated, eco-friendly, low-cost, and efficient sample pretreatment technique for quick analysis of TCS in environmental wastewaters.

Hormesis Effect of Methyl Triclosan on Cell Proliferation and Migration in Human Hepatocyte L02 Cells

Methyl triclosan (mTCS) is a methylated derivative of triclosan (TCS), which is extensively used as an antimicrobial component of various nursing products and disinfectants. Current research studies of mTCS mainly focused on the environmental persistence and bioaccumulation potential. Knowledge regarding the toxicity and carcinogenicity of mTCS is limited until now. In this study, the human hepatocyte L02 cells were used to investigate the cellular effects of mTCS under different concentrations (0.1-60 μM). The hormesis effect was observed where a low dose of mTCS (≤5 μM) exposure stimulated the cell proliferation ability, while high-dose exposure (≥20 μM) inhibited cell proliferation. In the same time, low doses of mTCS (0.5 and 1 μM) induced enhanced anchorage-independent proliferation ability and cell migration ability, indicating a positive effect on malignant transformation in L02 cells. Moreover, reactive oxygen species productions were significantly increased after mTCS exposure (≥1 μM), as compared with the control group. Furthermore, expressions of tumor-related genes, mouse double minute 2 (MDM2), matrix metalloproteinase 9 (MMP9), and proliferating cell nuclear antigen (PCNA), and proto-oncogene MYC (c-Myc), Jun, and FosB were significantly upregulated, while no significant changes were observed on expressions of apoptosis-related and cell cycle-related genes in L02 cells after exposure of low-dose mTCS. In conclusion, these results indicated that a low dose of mTCS had a hormesis effect in L02 cells on cell proliferation and malignant transformation in vitro, which might be mediated through oxidative stress response.

Removal of phenolic contaminants from water by in situ coated surfactant on Keggin-aluminum nanocluster and biodegradation

Recent water treatment plants require multi-process techniques to remove contaminants from aqua media. In this study, we investigate the novel, in situ coated sodium dodecylsulphate (SDS), on kegging Al₃₀ nanocluster as a single water treatment alternative for the removal of phenolic contaminants and suspension. FTIR, TEM-EDX and Zeta potential analysis characterized the nanocluster decoration. The resulting property was examined by emission (λ-max) of the molecular probe, the online aggregate image of fluorescence microscopy, and mixing isochrone, fat-soluble dye solubilization. The coated media was examined as nearly resembling the hydrophobicity of 1-octanol. The elemental line scanning and mapping showed different morphologies of floc depending on the SDS concentration. The material was found to follow Brownian motion to enmesh suspended particles like a ladder, and served as entrapper for small organic contaminants by the sorbed SDS aggregate, based on their log K_O/W. About 85% and ≥95% removal archived for contaminants with the least and highest K_O/W value, respectively. The residual solutes in the supernatant were well decomposed by using a bacterial agent. One-step removal (less footprint) and ease of operation make this approach an environmentally compatible and cost-effective alternative for the large-scale treatment process.

Electrochemical Treatment of Effluent for the Removal of Contaminants of Emergent Concern and Culturable Microorganisms

The present work aims to study the electrochemical (EC) process applied for the removal of contaminants of emergent concern (CECs) from wastewater after secondary treatment and the effect of the process on the total culturable microorganisms. The EC experiments were performed in a cylindrical open reactor with 500 mL of effluent, and a fixed current density of 8 mA/cm² was applied through mixed metal oxide electrodes. The experiments were conducted in different sets. In the first round (Set 1), the effluent sample was spiked with three CECs (200 ppb each): caffeine (CAF), carbamazepine (CBZ), and oxybenzone (OXY). For the best treatment period, 6 h, electrodegradation rates ranged from 41 ± 7% for CAF to 95 ± 6% for OXY, with an 87% removal of total culturable microorganisms. In the second round (Set 2), aiming to assess EC process efficiency in a more complex CEC mixture, the effluent was spiked with six more CECs (200 ppb each): diclofenac (DCF), triclosan (TCS), bisphenol A (BPA), 17β-estradiol (E2), 17α-ethinylestradiol (EE2), and ibuprofen (IBU), giving a total of nine CECs. In this case, the EC process allowed decreasing the CEC content by 19–100% (below the limit of detection), depending on the effluent samples, and the culturable microorganisms by 99.98% after a 6 h treatment. By contributing to CEC degradation and microorganism removal, the EC process proved to be a viable remediation and disinfection technology for secondary effluent from wastewater treatment plants.

Electrodialytic treatment of secondary mining resources for raw materials extraction: Reactor design assessment

The sustainability of mining activities is compromised due to the high amounts of mining residues generated that have to be disposed of, often in open dams, that may cause environmental deterioration, e.g. release of toxic elements to water supplies. These residues are, however, secondary resources of raw materials. In the case of Panasqueira mine, they even are a source of tungsten, considered a critical raw material. The present work aims to assess the electrodialytic process efficiency for raw materials extraction from Panasqueira mine residues. Experiments were performed with 2 and 3-compartment electrodialytic reactors, applying current intensities between 50 and 100 mA, from 4 to 14 days, and sample suspensions enhanced with NaCl or effluent. Additionally, control experiments with no current application were carried out. The results showed that a 3-compartment reactor operating at 100 mA, with NaCl as supporting electrolyte, presented the highest extraction of copper (13%), tin (10%), tungsten (13%) and arsenic (63%).

TiO2 Synthesis by the Pechini's Method and Application for Diclofenac Photodegradation†

In this work, the effect of the calcination temperature on the TiO₂ synthesis using Pechini's method was reported. The adopted calcination temperatures were 500, 600, and 700°C. XRD measurements indicated the composition of crystalline phases, and from there, the conversion of the anatase phase to rutile. TiO₂ Evonik^® was used as a reference standard and sodium diclofenac as a standard for photodegradation assessment. The average crystalline size increased. In both cases, this trend accompanied the increase in calcination temperature. The optical properties were performed using diffuse UV-Vis reflectance. Results obtained indicated maximum absorption wavelength values more intense and displaced to the visible region. Also, the estimated band gap energy values decreased. The photocatalytic performance of TiO₂ samples was superior to the reference catalyst (TiO₂ Evonik^® ). Especially in the first 10 minutes, the comparative photodegradation was up to approximately 58% higher. The photodegradation kinetic constants were also higher, and by comparison, up to approximately 73% higher. Toxicity measurements, using Artemias salina, also indicated similar decay behavior in the first 10 minutes, with a performance of up to approximately 60%.