Selective copper recovery by membrane distillation and adsorption system from synthetic acid mine drainage

Enhanced copper removal by magnesium modified biochar derived from Alternanthera philoxeroides

Adsorption processes are being widely used by various researchers for the removal of heavy metals from waste streams and biochar has been frequently used as an adsorbent. In this study, a MgO-loaded biochar derived from Alternanthera philoxeroides (MAPB) was synthesized for the removal of Cu(II). Compared with other biochar absorbents, MAPB showed a relatively slow adsorption kinetics, but an effective removal of Cu(II) with a maximum sorption capacity of 1, 238 mg/g. The adsorption mechanism of Cu(II) by MAPB was mainly controlled by chemical precipitation as Cu2(OH)3NO3, complexation and ion replacement. Fixed bed column with MAPB packed in same dosage (1, 000 mg) and different bed depth (1.3, 2.6 and 3.9 cm) showed that the increased of bed depth by mixing MAPB with quartz sand could increase the removal of Cu(II). The fitted breakthrough (BT) models showed that mixing MAPB with support media could reduce the mass transfer rate, increase the dynamic adsorption capacity and BT time. Therefore, MAPB adsorbent act as a highly efficient long-term adsorbent for Cu(II) contaminated water treatment may have great ecological and environmental significance.

Membrane-based technology in water and resources recovery from the perspective of water social circulation: A review

In this review, the application of membrane-based technology in water social circulation was summarized. Water social circulation encompassed the entire process from the acquirement to discharge of water from natural environment for human living and development. The focus of this review was primarily on the membrane-based technology in recovery of water and other valuable resources such as mineral ions, nitrogen and phosphorus. The main text was divided into four main sections according to water flow in the social circulation: drinking water treatment, agricultural utilization, industrial waste recycling, and urban wastewater reuse. In drinking water treatment, the acquirement of water resources was of the most importance. Pressure-driven membranes, such as ultrafiltration (UF), nanofiltration (NF) and reverse osmosis (RO) were considered suitable in natural surface water treatment. Additionally, electrodialysis (ED) and membrane capacitive deionization (MCDI) were also effective in brackish water desalination. Agriculture required abundant water with relative low quality for irrigation. Therefore, the recovery of water from other stages of the social circulation has become a reasonable solution. Membrane bioreactor (MBR) was a typical technique attributed to low-toxicity effluent. In industrial waste reuse, the osmosis membranes (FO and PRO) were utilized due to the complex physical and chemical properties of industrial wastewater. Especially, membrane distillation (MD) might be promising when the wastewater was preheated. Resources recovery in urban wastewater was mainly divided into recovery of bioenergy (via anaerobic membrane bioreactors, AnMBR), nitrogen (utilizing MD and gas-permeable membrane), and phosphorus (through MBR with chemical precipitation). Furthermore, hybrid/integrated systems with membranes as the core component enhanced their performance and long-term working ability in utilization. Generally, concentrate management and energy consumption control might be the key areas for future advancements of membrane-based technology.

Enhanced synergistic removal of Cu(II) and Cr(VI) with multifunctional biomass hydrogel from strong-acid media

Simultaneous recovery of heavy metal ions (HMIs) such as Cu(II) and Cr(VI) from strong-acid media was a great challenge due to the inhibition of protons. Herein, a novel biomass hydrogel (CMC/PEI-PD) containing various groups (bis-picolylamine, amino, and hydroxyl groups) was newly prepared by a facile two-step process. The static experiments relating pH, kinetics and isothermal co-adsorption confirmed the synergistic effect towards Cu(II) and Cr(VI) consistently. Specifically, the adsorption capacities of Cu(II) and Cr(VI) at pH 2.0 increased by 23.73% and 40.18% in comparison with the single systems. Moreover, coexistence of inorganic anions and cations could further increase the adsorption of Cu(II) and Cr(VI) by 59.90% and 43.39%, respectively. At the same time, the adsorption and desorption ratios for both HMIs remained stable. The superior performance came from the two dominant mechanisms of co-removal. On the one hand, Cu(II) chelated by bis-picolylamine group attracted Cr(VI) in the form of cation bridge, thus promoting Cr(VI) adsorption. On the other hand, the protonated amine group attracted Cr(VI) by electrostatic interaction and weakened the inter-cationic repulsion by electrostatic shielding, thus promoting Cu(II) adsorption. In addition, the dynamic column experiment towards simulated acidic electroplating wastewater involving Cu(II)-Cr(VI)-Ni(II) certified the high efficiency and feasibility of the co-removal. Therefore, CMC/PEI-PD owned great potential in the separation of typical HMIs even directly from strong-acid media.

Acid mine drainage (AMD) treatment using galvanic electrochemical system Al-Cu

Acid mine drainage was evaluated using a galvanic (GV) electrochemical system, Al-Cu (anode/cathode), based on a 32 factorial design. The factors analyzed were anodic area/volume ratios (A/V) of 0.037, 0.072, and 0.112 cm2/cm3, and treatment time from 0.25-8 h, and analyses were performed in duplicate with 11 degrees of freedom. The response variables were the total dissolved solids and concentrations of As, Cu, Co, Cr, Pb, Fe, Ni, and S O 4 2 - . The pH, electrical conductivity, and temperature were monitored during the process. Significant differences between treatments were determined by analysis of variance with Tukey's test (p < 0.05) using Statgraphics Centurion XVI.I software. The results showed that a greater electrode surface, A/V ratio, and treatment time improved pollutant removal. The spontaneous reactions generated by the galvanic cell, through the current that flows owing to the potential difference between the Al and Cu electrodes, allows the removal of heavy metals, arsenic, and S O 4 2 - by coagulation and precipitation mechanisms. The removal efficiencies achieved were Cu (99.1%), As (76.6%), Ni (80.2%), Pb (83.6%), Cr (100%), Fe (93.71%), and 92.9% for sulfates. The X-ray diffraction and Raman analyses of the solid fraction indicated that cuprite was formed with a purity of 96%, and the recovery of Cu by the GV system may be a viable option for mining companies.

Competitive adsorption behavior of typical heavy metal ions from acid mine drainage by multigroup-functionalization cellulose: qualitative and quantitative mechanism

In response to Cd, Pb, and Cu pollution in acid mine drainage (AMD), a multigroup cellulose material (TCIS) containing thiol (-SH), carboxyl (-COOH), and imine (-C = N) groups was prepared through oxidation and grafting reactions. At pH 5, the maximum Cd(II), Pb(II), and Cu(II) adsorption performances of TCIS were 53.60, 120.6, and 36.01 mg/g, respectively. In the binary system, the interaction between metal ions was mainly inhibited by competitive adsorption. Cu(II) exhibited the most fierce inhibitory effect and had a relatively stable adsorption performance. In the ternary system, the adsorption order was Cu(II) > Cd(II) > Pb(II). In density functional theory (DFT) calculations, we combined the molecular electrostatic potentials, binding energies, differential charges, and total potentials to illustrate the competitive behavior of metal ions at different binding sites. Moreover, X-ray photoelectron spectroscopy (XPS) and DFT analysis revealed that the adsorption process of TCIS was dominated by the above functional groups, which caused competitive adsorption among Cd(II), Pb(II), and Cu(II).

Innovative Membrane Technologies for the Treatment of Wastewater Polluted with Heavy Metals: Perspective of the Potential of Electrodialysis, Membrane Distillation, and Forward Osmosis from a Bibliometric Analysis

A bibliometric analysis, using the Scopus database as a source, was carried out in order to study the scientific documents published up to 2021 regarding the use of electrodialysis, membrane distillation, and forward osmosis for the removal of heavy metals from wastewater. A total of 362 documents that fulfilled the search criteria were found, and the results from the corresponding analysis revealed that the number of documents greatly increased after the year 2010, although the first document was published in 1956. The exponential evolution of the scientific production related to these innovative membrane technologies confirmed an increasing interest from the scientific community. The most prolific country was Denmark, which contributed 19.3% of the published documents, followed by the two main current scientific superpowers: China and the USA (with 17.4% and 7.5% contributions, respectively). Environmental Science was the most common subject (55.0% of contributions), followed by Chemical Engineering (37.3% of contributions) and Chemistry (36.5% of contribution). The prevalence of electrodialysis over the other two technologies was clear in terms of relative frequency of the keywords. An analysis of the main hot topics identified the main advantages and drawbacks of each technology, and revealed that examples of their successful implementation beyond the lab scale are still scarce. Therefore, complete techno-economic evaluation of the treatment of wastewater polluted with heavy metals via these innovative membrane technologies must be encouraged.

Valorization of wastewater to recover value-added products: A comprehensive insight and perspective on different technologies

In recent years, due to rapid globalization and urbanization, the demand for fuels, energy, water and nutrients has been continuously increasing. To meet the future need of the society, wastewater is a prominent and emerging source for resource recovery. It provides an opportunity to recover valuable resources in the form of energy, fertilizers, electricity, nutrients and other products. The aim of this review is to elaborate the scientific literature on the valorization of wastewater using wide range of treatment technologies and reduce the existing knowledge gap in the field of resource recovery and water reuse. Several versatile, resilient environmental techniques/technologies such as ion exchange, bioelectrochemical, adsorption, electrodialysis, solvent extraction, etc. are employed for the extraction of value-added products from waste matrices. Since the last two decades, valuable resources such as polyhydroxyalkanoate (PHA), matrix or polymers, cellulosic fibers, syngas, biodiesel, electricity, nitrogen, phosphorus, sulfur, enzymes and a wide range of platform chemicals have been recovered from wastewater. In this review, the aspects related to the persisting global water issues, the technologies used for the recovery of different products and/or by-products, economic sustainability of the technologies and the challenges encountered during the valorization of wastewater are discussed comprehensively.

Magnetic biochar derived from macroalgal Sargassum hemiphyllum for highly efficient adsorption of Cu(II): Influencing factors and reusability

In this study, the brown algae Sargassum Hemiphyllum was used as a carbon source for synthesis of magnetic porous biochar via pyrolyzing at high temperature and and doping iron oxide particles (Fe-BAB). Cu (II) species were removed from aqueous solutions using Fe-BAB under various conditions. Fe-BAB demonstrated superior Cu (II) adsorption (105.3 mg g-1) compared to other biochars. On the surface of Fe-BAB, there are several oxygen-containing functional groups, such as -COOH and -OH, which are likely responsible for the excellent heavy metal removal performance. By utilizing magnet, the Fe-BAB can be conveniently separated from the solution and ready for further usage. Multi-adsorption mechanisms were responsible for Cu adsorption on Fe-BAB. Using the magnetic algal biochar for heavy metal removal is feasible due to its high adsorption efficiency and simplicity of separation.

Resource Utilization of Acid Mine Drainage (AMD): A Review

Acid mine drainage (AMD) is a typical type of pollution originating from complex oxidation interactions that occur under ambient conditions in abandoned and active mines. AMD has high acidity and contains a high concentration of heavy metals and metalloids, posing a serious threat to ecological systems and human health. Over the years, great progress has been made in the prevention and treatment of AMD. Remediation approaches like chemical neutralization precipitation, ion exchange, membrane separation processes, and bioremediation have been extensively reported. Nevertheless, some limitations, such as low efficacy, excessive consumption of chemical reagents, and secondary contamination restrict the application of these technologies. The aim of this review was to provide updated information on the sustainable treatments that have been engaged in the published literature on the resource utilization of AMD. The recovery and reuse of valuable resources (e.g., clean water, sulfuric acid, and metal ions) from AMD can offset the cost of AMD remediation. Iron oxide particles recovered from AMD can be applied as adsorbents for the removal of pollutants from wastewater and for the fabrication of effective catalysts for heterogeneous Fenton reactions. The application of AMD in beneficiation fields, such as activating pyrite and chalcopyrite flotation, regulating pulp pH, and leaching copper-bearing waste rock, provides easy access to the innovative utilization of AMD. A review such as this will help researchers understand the progress in research, and identify the strengths and weaknesses of each treatment technology, which can help shape the direction of future research in this area.

A novel method based on membrane distillation for treating acid mine drainage: Recovery of water and utilization of iron

Rapid and highly efficient treatment of acid mine drainage (AMD) is still challenging due to the low pH and high metal concentrations in it. This research focuses on a novel treatment method of AMD using direct contact membrane distillation (DCMD) and photocatalysis to recover water and utilize iron. In the DCMD process without pretreatment, the flux decreased by 93.38%. If pretreated by adding sodium oxalate, scale formation potential was effectively mitigated due to the removal of calcium and complexing of iron. For the treatment of the pretreated AMD (PAMD), 60% of water was recovered in the DCMD process with the flux decrease of 22%. The concentrate obtained from the DCMD process demonstrated high photocatalytic activity in the methylene blue (MB) degradation in an aqueous solution. In addition, the Fe (III)-oxalate complexes in the concentrate were reduced to insoluble Fe (II)-oxalate with visible light irradiation, which could be separated by sedimentation and used as a Fenton catalyst. Hence, this novel method exhibits great advantages on effectively inhibiting DCMD membrane fouling during AMD treatment, producing high-quality distillate with low conductivity, and realizing near zero-discharge of AMD.

Continuous and selective copper recovery by multi-modified and granulated SBA-15

Continuous and selective recovery of copper (Cu) from heavy metal wastewater not only mitigates the pollution of environment but also can be applied for industrial field. Due to several advantages such as large pore size, easy modification, physical and chemical stabilities, mesoporous silica material, SBA-15, has been synthesized via hydrothermal reaction in this study. For enhancing the adsorption capacity and selectivity for Cu ions, prepared SBA-15 was modified with manganese loading and amine-grafting (MN-SBA) then granulated by alginic-acid (GMN-SBA), successfully. Adsorption capacities for heavy metals such as Cu, Zn, Ni and Mn were 2.11, 1.24, 1.74 and 1.25 mmol/g on MN-SBA and decreased to 1.23, 0.68, 0.86 and 0.65 when it was granulated. Even though the adsorption capacities of GMN-SBA for heavy metals decreased by 40-50%, it enabled easy regeneration and separation process when applied for continuous fixed-bed column adsorption mode. Specifically, the results demonstrated that GMN-SBA was able to be reused for 5 times while maintaining over 80% adsorption capacities. Fixed-bed adsorption results were well explained by dynamic adsorption model incorporated with linear driving force approximation (LDFA) model. The simulation of fixed-bed adsorption tests was proceeded in terms of bed length, feeding concentration and flow rate, and it showed the breakthrough times were shifted in the axis of time. In multi-component adsorption, LDFA model showed a high overshoot phenomenon of the breakthrough curves for Zn, Ni and Mn compared to Cu. This reflected the high affinity of Cu towards GMN-SBA compared to other heavy metals.