Synergistic activation of peroxymonosulfate via in situ growth FeCo2O4 nanoparticles on natural rectorite: Role of transition metal ions and hydroxyl groups

The role of chitosan in promoting the catalytic activity of bismuth ferrite as peroxymonosulfate activator for antibiotics removal

Chitosan possesses electron-rich amino (-NH2) and hydroxyl (-OH) moieties which can anchor with transition metal ions during synthesis. Herein, chitosan was employed as an additive to prepare bismuth ferrite (BFO) via hydrothermal approach. The characterization studies revealed that adding chitosan during BFO synthesis leads to the creation of more oxygen vacancies. The performance of chitosan modified BFO (CMB) was evaluated as peroxymonosulfate (PMS) activator for ciprofloxacin (CIP) removal. Apparently, the addition of 10 wt% chitosan during BFO synthesis (CMB-10) resulted in 1.7 times increase of performance compared to the pristine BFO. Increasing the catalyst loading and PMS dosage resulted in positive effect with 5.7 and 1.9 times rate enhancement, respectively. The CMB-10 exhibited tolerance against pH variation, water matrix, and interfering species. The scavenging experiments indicated that singlet oxygen (1O2), superoxide radicals (O2•-) and sulfate radicals (SO4•-) played a major role in CIP degradation. These reactive oxygen species were generated from PMS activation via Fe3+/Fe2+ and Bi5+/Bi3+ coupling, and oxygen vacancies on the catalyst surface. The CIP degradation pathways were also elucidated based on the detected CIP intermediates. Overall, this study provides insights into the use of chitosan to prepare sustainable materials for pollutants removal via PMS activation.

Introducing and Boosting Oxygen Vacancies within CoMn2O4 by Loading on Planar Clay Minerals for Efficient Peroxymonosulfate Activation

CoMn2O4 (CMO) has been recognized as an effective peroxymonosulfate (PMS) activator; however, it still shows disadvantages such as limited reactive sites and metal leakage. Herein, an effective and environmentally friendly composite catalyst, CMO/Kln, was synthesized by anchoring CMO on kaolinite (Kln), a natural clay mineral with a special lamellar structure, to activate peroxymonosulfate (PMS) for the degradation of residue pharmaceuticals in water. The abundant hydroxyl groups located on the surface of Kln helped induce rich oxygen vacancies (OVs) into composite CMO/Kln, which not only acted as additional active sites but also accelerated working efficiency. In addition, compared with bare CMO, CMO/Kln showed lower crystallinity, and the adoption of the Kln substrate contributed to its structural stability with lower metal leaching after three rounds of reaction. The universal applicability of CMO/Kln was also verified by using three other pharmaceuticals as probes. This work shed light on the adoption of natural clay minerals in modifying CMO catalysts with promoted catalytic activity for the efficient and eco-friendly remediation of pharmaceuticals in wastewater.

Insight into the role of reactive species on catalyst surface underlying peroxymonosulfate activation by P-Fe2MnO4 loaded on bentonite for trichloroethylene degradation

In this study, bentonite supporting phosphorus-doped Fe2MnO4 (BPF) was synthesized and applied for PMS activation to degrade TCE. Morphology and structure characterization results indicated the successfully synthesized of BPF, and the BPF/PMS system not only featured high TCE removal (97.4%) but also high reaction rate constant (kobs = 0.0554 min-1) and PMS utilization (70.4%, kobs = 0.0228 min-1). According to the results of various experiments, massive oxygen vacancies on P-Fe2MnO4 alter its charge balance and facilitate the electron transfer process named adjacent transfer (direct electron capture by adsorbed PMS from adjacent TCE). Mn(III) is the main adsorption site for PMS, and the hydroxyl groups on the catalyst (Fe sites of P-Fe2MnO4, Si and Al sites of bentonite) can also offer binding sites for PMS. The hydrogen-bonded PMS on Fe(III) and Mn(III) sites will subsequently accept the discharged electrons to generate free radicals and high-valent metal species. Meanwhile, electron loss of HSO5- that chemically bonded to hydroxyl groups on bentonite will generate SO5•-, which will further produce 1O2 through self-bonding. the active species on the catalyst surface contribute 65% of TCE degradation in the heterogeneous catalytic oxidation system.

Photo-electrochemical activation of persulfate for the simultaneous degradation of microplastics and personal care products

The recent widespread use of microplastics (MPs), especially in pharmaceuticals and personal care products (PPCPs), has caused significant water pollution. This study presents a UV/electrically co-facilitated activated persulfate (PS) system to co-degrade a typical microplastic polyvinyl chloride (PVC) and an organic sunscreen p-aminobenzoic acid (PABA). We investigated the effect of various reaction conditions on the degradation. PVC and PABA degradation was 37% and 99.22%, respectively. Furthermore, we observed alterations in the surface topography and chemical characteristics of PVC throughout degradation. The possible degradation pathways of PVC and PABA were proposed by analyzing the intermediate products and the free radicals generated. This study reveals the co-promoting effect of multiple mechanisms in the activation by ultraviolet light and electricity.

Multifunctional Nanoclay-Based Hemostatic Materials for Wound Healing: A Review

Bleeding to death accounts for around 30-40% of all trauma-related fatalities. Current hemostatic materials are mainly mono-functional or have insufficient hemostatic capacity. Nanoclay has been recently shown to accelerate hemostasis, improve wound healing, and provide the resulting multifunctional hemostatic materials antibacterial, anti-inflammatory, and healing-promoting due to its distinctive morphological structure and physicochemical properties. Herein, the chemical design and action mechanism of nanoclay-based hemostatic, antibacterial, and pro-wound healing materials in the context of wound healing are discussed. The physiological processes of hemostasis and wound healing to elucidate the significance of nanoclay for functional wound hemostatic dressing design are outlined. A summary of the features of various nanoclay and product types used in wound hemostatic dressings is provided. Nanoclay can be antimicrobial due to the slow release of metal ions and has an abundant surface charge allowing for high affinity for proteins and cells, which can activate the coagulation reaction or facilitate tissue repair. Nanoclay with a microporous structure can be used as drug carriers to create composites critical for inhibiting bacterial growth on wounds or promoting the regeneration of vascular, muscle, and skin tissues. Directions for further research and innovation of nanoclay-based multifunctional materials for hemostasis and tissue regeneration are explored.

Facilitated Visible-Light-Driven Peroxymonosulfate Activation by a Co-Fe Layered Double Hydroxide Derived p-n Heterostructure for Sulfadiazine Degradation: Affecting Parameters, Kinetics, and Mechanistic Insights

The utilization of multivalence ionic metal species generated through a peroxymonosulfate (PMS)-assisted photocatalytic system is a promising platform for the selective degradation of water contaminants. However, achieving an effective electron transport and enhanced separation efficiency for these metal species is a daunting challenge. Thus, our current study addresses this challenge by using a Co-Fe-based layered-double-hydroxide template to synthesize a Co3O4/FeCo2O4 p-n heterojunction composite via a simple monosynthetic route. The resultant composite is thoroughly validated through advanced characterization techniques that efficiently activate PMS for sulfadiazine (SDZ) degradation under visible light, achieving a remarkable degradation efficiency of up to 90%. This accomplishment is attributed to factors including intimate interfacial contact, excellent light harvesting, mesoporosity, and oxygen vacancies within the composite. The formation of a distinct p-n heterojunction following the S-scheme charge dynamic significantly enhances photogenerated carrier separation and reduces charge recombination. The research delves into comprehensive investigations including degradation studies, active species trapping experiments, parameter exploration, and in-depth liquid chromatography-mass spectrometry for analysis of the degradation byproducts and pathway. Induced oxygen vacancies, strategically placed active surface sites, and mesoporosity in the Co3O4/FeCo2O4 composite synergistically boosted the sluggish PMS activation, leading to enhanced SDZ degradation. This study introduces a new perspective by demonstrating the potential of a single-material, mixed-metal oxide-based p-n heterojunction photocatalytic system following the S-scheme charge-transfer route for SDZ degradation. The findings contribute toward emphasizing the importance of tailored composite materials in tackling persistent contaminants.

Starch of oat derived nanostructured Fe/Mn bimetallic carbon materials for sulfamethoxazole degradation via peroxymonosulfate activation

Fe/Mn bimetallic carbon materials were synthesized by combining oat and urea, followed by and carbonization processes, the activity and mechanism of the obtained materials in activating peroxymonosulfate (PMS) for sulfamethoxazole (SMX) degradation were determined. Data suggested that the obtained material (CN@FeMn-10-800) showed the optimal performance for SMX degradation under the1:8:0.05:0.05 mass ratios of oat/urea/Fe/Mn. Around 91.2 % SMX (10 mg L-1) was removed under the conditions of 0.15 g L-1 CN@FeMn-10-800 and 0.20 g L-1 PMS. The CN@FeMn-10-800 showed great adaptability under different conditions, satisfactory activation repeatability and versatility. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) demonstrated that core-shell structure with rich porous of CN@FeMn-10-800 was achieved. Quenching test and electron paramagnetic resonance (EPR) indicated that surface bound oxygen and singlet oxygen (1O2) were the dominate reactive groups in this system. X-ray photoelectron spectroscopy (XPS) suggested that graphite N, Fe0, Fe3C and Mn(II) were the dominant active sites. Through the work, a simple strategy could be found to make high-value use of biomass and use it to effectively purified wastewater.

Enhanced Degradation of Levofloxacin through Visible-Light-Driven Peroxymonosulfate Activation over CuInS2/g-C3N4 Heterojunctions

In this work, the heterojunctions of CuInS2 embedded in the g-C3N4 materials (xCuInS2/g-C3N4, abbreviated as xCIS/GCN) was successfully prepared for peroxymonosulfate (PMS) activation under visible light. The catalysts are characterized by different techniques, such as XRD, FTIR, SEM, TEM, and UV-vis. The unique heterojunction composites can suppress the recombination of photogenerated pairs. The catalytic results showed that the 3CIS/GCN exhibited excellent catalytic levofloxacin (LVF) degradation efficiency, while more than 98.9% of LVF was removed in 60 min over a wide pH range. SO4•-, O2•-, OH•, and 1O2 were verified as the main reactive species for LVF degradation via the quenching experiments and electron paramagnetic resonance technology (EPR). The synergetic effect of xCIS/GCN, PMS, and visible light irradiation was discussed. The possible LVF degradation pathway was proposed through byproducts analysis (LC-MS). Moreover, the 3CIS/GCN/vis-PMS system has very low metal leaching. Owing to xCIS/GCN having good properties for PMS activation, it has potential applications for LVF or other hazardous pollutants degradation.

Textile dye removal in wastewater by peroxymonosulfate (PMS) activation on a zero-valent iron nanoparticle-modified ultrafiltration catalytic membrane (nZVI@PES)

The use of the nano zero-valent iron (nZVI) nanoparticle-based advanced oxidation systems in conjunction with an activator such as peroxymonosulfate (PMS) to generate hydroxyl and sulfate radicals for the degradation of organic pollutants has been extensively used in recent studies. In this study, a nZVI-modified polyethersulfone (PES) membrane (nZVI@PES) was produced successfully by attaching the nZVI catalytic nanoparticles on the surface of a commercial microporous polymeric membrane material using a simple and easy filter press coating method. The presence of nZVI nanoparticles on the nZVI@PES membrane was confirmed by XRD, SEM, and EDS analyses. The nZVI@PES membrane was applied in the dead-end filtration system in the presence of the PMS activator to treat the reactive black 5 (RB5) dye solution. The effect of catalyst loading, RB5 dye concentration, PMS dosage, and pH level on the nZVI@PES membrane/PMS system was investigated. Quenching experiments were carried out to identify the reactive species responsible, and reusability tests were conducted on the membrane. The highest decolorization efficiency (96.8%) was obtained at 20 mg/L RB5 dye solution, initial pH of 3, the nZVI loading of 5 mg/cm2, and the PMS dosage of 300 mg/L at the end of a reaction time of 30 min. The formation of HO•, [Formula: see text], [Formula: see text] and, 1O2 was confirmed by quenching experiments. The results indicate that the nZVI@PES membrane/PMS system could successfully treat wastewater contaminated with an organic dye.

Peroxymonosulfate activation by graphene oxide-supported 3D-MoS2/FeCo2O4 sponge for highly efficient organic pollutants degradation

To address conventional powder catalysts' recovery and aggregation issues that greatly restrain their practical application, a recoverable graphene oxide (GO)-supported 3D-MoS₂/FeCo₂O₄ sponge (SFCMG) was developed through a simple impregnation pyrolysis method. SFCMG can efficiently activate peroxymonosulfate (PMS) to produce reactive species for rapid degradation of rhodamine B (RhB), with 95.0% and 100% of RhB being removed within 2 min and 10 min, respectively. The presence of GO enhances the electron transfer performance of the sponge, and the three-dimensional melamine sponge serves as a substrate to provide a highly dispersed carrier for FeCo₂O₄ and MoS₂/GO hybrid sheets. SFCMG exhibits a synergistic catalytic effect of Fe and Co, and facilitates the redox cycles of Fe(III)/Fe(II) and Co(III)/Co(II) by MoS₂ co-catalysis, which enhances its catalytic activity. Electron paramagnetic resonance results demonstrate that SO₄^•-, ·O₂^- and ¹O₂ are all involved in SFCMG/PMS system, and ¹O₂ played a prominent role in RhB degradation. The system has good resistance to anions (Cl^-, SO₄^2-, and H₂PO₄^-) and humic acid and excellent performance for many typical contaminants degradation. Additionally, it works efficiently over a wide pH range (3-9) and possesses high stability and reusability with the metal leaching far below the safety standards. The present study extends the practical application of metal co-catalysis and offers a promising Fenton-like catalyst for the treatment of organic wastewater.

Degradation of atrazine by electroactivation of persulfate using FeCuO@C modified composite cathode: Synergistic activation mechanism

In sulfate radical-based advanced oxidation processes (SR-AOPs), high-efficiency and perdurable materials have drawn considerable interest for use as cathodes, which can effectively degrade refractory organic contaminants through the synergistic electro-activation and transition metal activation of persulfate (PS). Here, the FeCuO@C modified composite cathode (FeCuO@C/AGF) was synthesized via the solvothermal and thermal treatment method based on the CuFe-MOF-74 structure, and the electro-activation PS process (EC/FeCuO@C/AGF/PS) was developed to effectively remove atrazine (ATZ). The surface morphology, electrochemical characteristics, chemical composition, crystal structure, and electrode surface wettability of FeCuO@C/AGF were investigated. It was found that the proposed EC/FeCuO@C/AGF/PS process can successfully remove 100% of ATZ in 20 min at a low current density (2 mA cm^-2) and a low PS concentration (0.4 mM), and PS is successfully activated by combining the electrical and transition metal synergistic activation. The FeCuO@C/AGF cathode exhibits outstanding catalytic functionality over a broad pH range (2-9) and remains stable over five successive cycles. Additionally, the active species involved in the reaction as well as the potential ATZ degradation reaction mechanisms and pathways are discussed. Electrochemical oxidation is a process in which both radicals (SO₄^·-, ·OH, and O₂^·-) and non-radical (¹O₂) participate in the degradation of ATZ. The intermediates of the ATZ degradation process were studied upon the toxicity changing, and the toxicity of the intermediates was found to be reduced during degradation. These results present a novel approach toward the establishment of an effective and reliable electrode in SR-AOPs that can efficiently treat pesticide wastewater.

From Fenton and ORR 2e−-Type Catalysts to Bifunctional Electrodes for Environmental Remediation Using the Electro-Fenton Process

Currently, the presence of emerging contaminants in water sources has raised concerns worldwide due to low rates of mineralization, and in some cases, zero levels of degradation through conventional treatment methods. For these reasons, researchers in the field are focused on the use of advanced oxidation processes (AOPs) as a powerful tool for the degradation of persistent pollutants. These AOPs are based mainly on the in-situ production of hydroxyl radicals (OH•) generated from an oxidizing agent (H2O2 or O2) in the presence of a catalyst. Among the most studied AOPs, the Fenton reaction stands out due to its operational simplicity and good levels of degradation for a wide range of emerging contaminants. However, it has some limitations such as the storage and handling of H2O2. Therefore, the use of the electro-Fenton (EF) process has been proposed in which H2O2 is generated in situ by the action of the oxygen reduction reaction (ORR). However, it is important to mention that the ORR is given by two routes, by two or four electrons, which results in the products of H2O2 and H2O, respectively. For this reason, current efforts seek to increase the selectivity of ORR catalysts toward the 2e− route and thus improve the performance of the EF process. This work reviews catalysts for the Fenton reaction, ORR 2e− catalysts, and presents a short review of some proposed catalysts with bifunctional activity for ORR 2e− and Fenton processes. Finally, the most important factors for electro-Fenton dual catalysts to obtain high catalytic activity in both Fenton and ORR 2e− processes are summarized.

Effect of metal doping (Me = Zn, Cu, Co, Mn) on the performance of bismuth ferrite as peroxymonosulfate activator for ciprofloxacin removal

In this study, a facile hydrothermal method was employed to prepare Me-doped Bi₂Fe₄O₉ (Me = Zn, Cu, Co, and Mn) as peroxymonosulfate (PMS) activator for ciprofloxacin (CIP) degradation. The characteristics of the Me-doped bismuth ferrites were investigated using various characterization instruments including SEM, TEM, FTIR and porosimeter indicating that the Me-doped Bi₂Fe₄O₉ with nanosheet-like square orthorhombic structure was successfully obtained. The catalytic activity of various Me-doped Bi₂Fe₄O₉ was compared and the results indicated that the Cu-doped Bi₂Fe₄O₉ at 0.08 wt.% (denoted as BFCuO-0.08) possessed the greatest catalytic activity (k_app = 0.085 min^-1) over other Me-doped Bi₂Fe₄O₉ under the same condition. The synergistic interaction between Cu, Fe and oxygen vacancies are the key factors which enhanced the performance of Me-doped Bi₂Fe₄O₉. The effects of catalyst loading, PMS dosage, and pH on CIP degradation were also investigated indicating that the performance increased with increasing catalyst loading, PMS dosage, and pH. Meanwhile, the dominant reactive oxygen species was identified using the chemical scavengers with SO₄^•-, ^•OH, and ¹O₂ playing a major role in CIP degradation. The performance of BFCuO-0.08 deteriorated in real water matrix (tap water, river water and secondary effluent) due to the presence of various water matrix species. Nevertheless, the BFCuO-0.08 catalyst possessed remarkable stability and can be reused for at least four successive cycles with >70% of CIP degradation efficiency indicating that it is a promising catalyst for antibiotics removal.

Lignocellulosic Biorefinery Technologies: A Perception into Recent Advances in Biomass Fractionation, Biorefineries, Economic Hurdles and Market Outlook

Lignocellulosic biomasses (LCB) are sustainable and abundantly available feedstocks for the production of biofuel and biochemicals via suitable bioconversion processing. The main aim of this review is to focus on strategies needed for the progression of viable lignocellulosic biomass-based biorefineries (integrated approaches) to generate biofuels and biochemicals. Processing biomass in a sustainable manner is a major challenge that demands the accomplishment of basic requirements relating to cost effectiveness and environmental sustainability. The challenges associated with biomass availability and the bioconversion process have been explained in detail in this review. Limitations associated with biomass structural composition can obstruct the feasibility of biofuel production, especially in mono-process approaches. In such cases, biorefinery approaches and integrated systems certainly lead to improved biofuel conversion. This review paper provides a summary of mono and integrated approaches, their limitations and advantages in LCB bioconversion to biofuel and biochemicals.

Bicarbonate enhanced heterogeneous activation of peroxymonosulfate by copper ferrite nanoparticles for the efficient degradation of refractory organic contaminants in water

Nowadays, the treatment of residual refractory organic contaminants (ROCs) is a huge challenge for environmental remediation. In this study, a potential process is provided by copper ferrite catalyst (CuFe₂O₄) activated peroxymonosulfate (PMS, HSO₅^-) in the bicarbonate (HCO₃^-) enhanced system for efficient removal of Acid Orange 7 (AO7), 2,4-dichlorophenol, phenol and methyl orange (MO) in water. The impact of key reaction parameters, water quality components, main reactive oxygen species (ROS), probable degradation mechanism, rational degradation pathways and catalyst stability were systematically investigated. A 95.0% AO7 (C₀ = 100 mg L^-1) removal was achieved at initial pH (pH₀) of 5.9 ± 0.1 (natural pH), CuFe₂O₄ dosage of 0.15 g L^-1, PMS concentration of 0.98 mM, HCO₃^- concentration of 2 mM, and reaction time of 30 min. Both sulfate radical (SO₄^-•) and hydroxyl radical (^•OH) on the surface of catalyst were proved as the predominant radical species through radical quenching experiments and electron paramagnetic resonance (EPR) analysis. The buffer nature of HCO₃^- was partially contributed for the enhanced degradation of AO7 under CuFe₂O₄/PMS/HCO₃^- system. Importantly, according to ¹³C nuclear magnetic resonance (NMR) and EPR analysis, the positive effect of bicarbonate may be mainly attributed to the formation of peroxymonocarbonate (HCO₄^-), which may enhance the generation of ^•OH. The magnetic CuFe₂O₄ particles can be well recycled and the leaching concentration of Cu was acceptable (<1 mg L^-1). Considering the widespread presence of bicarbonate in water environment, this work may provide a safe, efficient, and sustainable technique for the elimination of ROCs from practical complex wastewater.

State-of-the-Art on the Sulfate Radical-Advanced Oxidation Coupled with Nanomaterials: Biological and Environmental Applications

Sulfate radicals (SO₄^-·) play important biological roles in biomedical and environmental engineering, such as antimicrobial, antitumor, and disinfection. Compared with other common free radicals, it has the advantages of a longer half-life and higher oxidation potential, which could bring unexpected effects. These properties have prompted researchers to make great contributions to biology and environmental engineering by exploiting their properties. Peroxymonosulfate (PMS) and peroxydisulfate (PDS) are the main raw materials for SO₄^-· formation. Due to the remarkable progress in nanotechnology, a large number of nanomaterials have been explored that can efficiently activate PMS/PDS, which have been used to generate SO₄^-· for biological applications. Based on the superior properties and application potential of SO₄^-·, it is of great significance to review its chemical mechanism, biological effect, and application field. Therefore, in this review, we summarize the latest design of nanomaterials that can effectually activate PMS/PDS to create SO₄^-·, including metal-based nanomaterials, metal-free nanomaterials, and nanocomposites. Furthermore, we discuss the underlying mechanism of the activation of PMS/PDS using these nanomaterials and the application of SO₄^-· in the fields of environmental remediation and biomedicine, liberating the application potential of SO₄^-·. Finally, this review provides the existing problems and prospects of nanomaterials being used to generate SO₄^-· in the future, providing new ideas and possibilities for the development of biomedicine and environmental remediation.

Efficient peroxymonosulfate activation of immobilized Fe-N-C catalyst on ceramsite for the continuous flow removal of phenol

Nowadays, developing environmentally friendly catalysts with both low cost and high efficiency was still a challenge in actual organic wastewater purification. Herein, the Fe-N-C catalyst was successfully immobilized on solid waste derived ceramsite for efficient degradation of phenol under continuous flow conditions by activating peroxymonosulfate (PMS). After the introduction of ceramsite, the microstructure of Fe-N-C catalyst was changed from granular structure to worm-like structure, promoting the dispersion of the nanoscale catalyst and providing more reactive sites. Therefore, the phenol removal rate and mineralization rate of the obtained 0.5FNNC within 30 min were up to 96.79% and 71.79%, respectively. In addition, the degradation rate of the optimal composite (0.5FNNC)/PMS system was about 4.06 times higher than that of bare Fe-N-C/PMS system. Intriguingly, the Fe ion leaching from 0.5FNNC during the degradation reaction was significantly lower than bare Fe-N-C owing to the strong catalyst-support chemical bonding. Based on electron paramagnetic resonance, quenching experiments, X-ray photoelectron spectroscopy analysis and electrochemical analysis, it was indicated that the non-radical processes (¹O₂ and high valent iron-oxo species) should be responsible for the phenol degradation. Meanwhile, the possible phenol degradation pathways were proposed, and the intermediates were evaluated for ecotoxicity by ECOSAR. Finally, a preliminary economic analysis of this process was carried out. Overall, this work would provide a new strategy for the construction of ceramsite based multi-pore composite catalysts and the large-scale application of persulfate oxidation technology in organic wastewater treatment.

Promotional effect of Ca doping on Bi2Fe4O9 as peroxymonosulfate activator for gatifloxacin removal

A series of Ca-doped bismuth ferrite was prepared at various %w/w of Ca via a facile hydrothermal method to obtain Bi_2XCa_2(1-X)Fe₄O₉ (denoted as BFOCa-X, where X = 1, 0.95, 0.90, 0.80, 0.50). The BFOCa-X catalysts were characterized, and the results showed that they consist of pure phase BFO with nanosheet-like morphology. The as-prepared BFOCa-X catalysts were used as peroxymonosulfate (PMS) activator for gatifloxacin (GAT) removal. It was found that the catalytic activity decreased in the following order: BFOCa-0.8 (90.2% GAT removal efficiency in 45 min, k_app = 0.084 min^-1)>BFOCa-0.95 > BFOCa-0.9 > BFOCa-0.5 > BFO indicating that BFOCa-0.8 has the optimized active sites for catalysis. The Ca dopant contributed to the increased oxygen vacancies and surface hydroxyl groups, promoting the catalytic PMS activation process. The k_app value increased gradually with increasing catalyst loading and PMS dosage while pH 9 presented the highest GAT removal rate. The GAT degradation rate was inhibited by PO₄³-, humic acid and NH₄⁺ but promoted in the presence of Cl-, NO₃- and HCO₃-. It was also found that the GAT can undergo several degradation pathways in the catalytic PMS system, which eventually mineralized into innocuous compounds. The dominant reactive oxygen species (ROS) were identified using chemical scavengers, revealing that SO₄^•-, ¹O₂ and ^•OH contributed significantly to GAT degradation. Based on the XPS study, PMS was activated by the Fe²⁺/Fe³⁺ redox cycling and oxygen vacancies to produce SO₄^•-/^•OH and ¹O₂, respectively. Overall, the BFOCa-0.8 also showed excellent reusability up to at least 4 cycles with low Bi and Fe leaching (<7 and 62 μg L^-1, respectively), indicating that it has promising potential for application as PMS activator for antibiotics removal.

High-efficient peroxymonosulfate activation for rapid atrazine degradation by FeSx@MoS2 derived from MIL-88A(Fe)

FeS_x@MoS₂-x (FM-x, x implied real Mo/Fe content ratios) in which FeS_x derived from MIL-88A deposited on the surface of MoS₂ with a tight heterogeneous interface were synthesized for peroxymonosulfate (PMS) activation to degrade atrazine (ATZ). The catalytic performance of FM-0.96 was greatly improved due to the rapid regeneration of Fe²⁺ resulting from the interfacial interaction. FM-0.96 could completely degrade 10.0 mg/L ATZ within 1.0 min, and the toxicities for most of its intermediates were greatly reduced. The k value of FM-0.96 was 320 and 40 times higher than that of the MoS₂ and FeS_x, respectively. The SO₄·^-, ·OH and ¹O₂ were mainly responsible for ATZ degradation in FM-0.96/PMS system, and the conversion pathway of ¹O₂ was analyzed. Furthermore, the long-term continuous operation for ATZ degradation was achieved using a fixed membrane reactor. This work provides deep insights into metal sulfide composites derived from metal-organic frameworks for removing pollutants by activating PMS.

Sulfate radicals induced from peroxymonosulfate on electrochemically synthesized TiO2-MoO3 heterostructure with Ti-O-Mo bond charge transfer pathway for potential organic pollutant removal under solar light irradiation

Here, a novel method for synthesis of heterostructured TiO₂-MoO₃ (MT) nanosheets photocatalyst by utilizing a facile electrochemical method and examined it's photocatalytic activity by the degradation of tetracycline hydrochloride (TCH), a model of organic pollutants, in the presence of peroxymonosulfate (PMS) under solar light irradiation (SL) was reported for the first time. The influence of several factors on the degradation efficiency including the initial concentration of TCH, solution pH, catalyst dosage, PMS concentration, and the existence of inorganic anions was explored. The MT-15/PMS system displayed a promising photocatalytic performance and up to 97% of TCH was degraded in 90 min the rate of the degradation reaction of MT-15/PMS was the highest (0.05299 min^-1) compared to 0.00251, 0.00337, 0.00546, 0.00735, 0.01337min^-1of TiO₂-P25, TiO₂-P25/PMS, MoO₃, MoO₃/PMS, and MT-15 respectively. The enhancement can be attributed to several reasons. First, the 2D morphology of the optimized heterostructure photocatalyst plays a significant role in providing much more active sites on its surface. Next, the boosted light absorption efficiency and higher photoproduced electron-hole pair separation ability, induced by the unique direct transformation of photogenerated electrons from the valance band of TiO₂ to the conduction band of MoO₃ via the Ti-O-Mo bond formed at the interface of MT heterostructure. Finally, the appropriate accessible reactive sites for the activation of PMS together with the synergistic effect between activation of PMS and photocatalytic processes eased the production of active species for the degradation of pollutants. Based on the scavenger experiments and EPR analysis, hydroxide and sulfate radicals were found to be the dominant free radical active species in the degradation process. Furthermore, the synergistic degradation reaction mechanism was proposed.

One-pot synthesis of a cellulose-supported CoFe2O4 catalyst for the efficient degradation of sulfamethoxazole

Cellulose-supported cobalt ferrite (CoFe₂O₄/RC) was synthesized via a facile one-pot hydrothermal method and demonstrated to be an efficient catalyst to activate peroxymonosulfate (PMS) for the degradation of sulfamethoxazole (SMX). The characterizations of CoFe₂O₄/RC catalysts revealed that an appropriate particle size of the cellulose support could promote the dispersion of CoFe₂O₄ nanoparticles and consequently promote the catalytic activity of the resulting CoFe₂O₄/RC catalysts. The degradation of SMX reached 97.6 % within 20 min at 30 °C with the CoFe₂O₄/RC/PMS system. The mechanism of SMX degradation over CoFe₂O₄/RC-activated PMS was studied via EPR, XPS, and quenching tests. The results suggested that ¹O₂ was the dominant reactive oxygen species and was accompanied by SO₄^-, OH, and O₂^- radicals for SMX degradation. The CoFe₂O₄/RC catalyst exhibited high stability and recyclability and maintained high catalytic activity after five experimental cycles.

Efficient organics heterogeneous degradation by spinel CuFe2O4 supported porous carbon nitride catalyst: Multiple electron transfer pathways for reactive oxygen species generation

Facilitating reactive oxygen species (ROS) generation is an effective way to promote the heterogeneous catalytic efficiency for organics removal. However, the metal leaching in metal-based catalysts and the low activity of non-metallic materials restrict ROS production. In this work, the purpose was achieved by loading a small amount of spinel CuFe₂O₄ onto porous carbon nitride substrate. The synthesized CuFe₂O₄@O-CN composite first to activate peroxymonosulfate (PMS), which produce a plenty of ROS (•OH, SO₄•^- and ¹O₂) for organics removal, leading to highly oxidation for diverse organics. Through the comparative analysis of the surface composition before and after reaction, we found that the interface multi-electron transfer routs, including surface Cu(II)/Cu(I), Fe(III)/Fe(II) and their cross interaction, participated in the redox cycle, giving rise to the rapid and massive production of ROS, so that DMPO and TEMP were instantly oxidized in electron paramagnetic resonance (ESR) detection. Importantly, the carrier of porous O-CN, which acted as the electron transfer mediator, not only favors PMS adsorption via surface -OH, but also facilitates the conversion between different metal species. As a result, the CuFe₂O₄@O-CN/PMS system can remove 99.1% BPA and achieve 52.6% mineralization under optimized conditions. Thus, this study not only sheds light on the tailored design of heterogeneous catalyst for organics removal and elucidates the interfacial catalytic mechanisms for PMS activation.

Induced morphology orientation of α-FeOOH by kaolinite for enhancing peroxymonosulfate activation

Persulfate activation technology based on sulfate radicals is currently a hot spot in the field of environmental governance. In our work, α-FeOOH was successful in situ loaded on kaolinite surface through a simple one-step hydrothermal process. The prepared composites were systematically characterized, and the relationship between the structural properties and peroxymonosulfate activation properties was explored. Interestingly, compared to bare α-FeOOH, the introduction of kaolinite in composite induced the transformation of α-FeOOH crystal and affected the morphology, where uniformly dispersed nanoparticles rather than rod-like agglomerated crystals appeared. The received FeOOH/kaolinite composite exhibited admirable adsorption and degradation of ciprofloxacin performance with the removal efficiency of 86.1%, and the degradation rate constant was up to 5.2 times higher than that of bare α-FeOOH. In addition, the main active species in the catalytic oxidation system are surface-bound SO₄^•-, ^•OH and free ¹O₂. This work would give a deep insight into the role of natural minerals in composite catalytic materials and the construction of high-efficient mineral-based composite materials.

Facile construction of high-performance 3D Co2C-doped CoAl2O4 fiber composites for capturing and decomposing tetracycline from aqueous solution

Herein, novel 3D hollow-carved Co₂C-doped CoAl₂O₄ fiber composites (3D-CA-FC) were successfully synthesized via a simple-green pyrolysis method and exhibited remarkably outstanding elimination performance for tetracycline (TC) by adsorption and degradation. The results indicated that the TC adsorption process of the samples could be accurately described by the pseudo-second-order and Langmuir isothermal model, and the maximum TC uptake reached up to 1889.63 mg/g under neutral conditions. Meanwhile, 3D-CA-FC showed good affinity for TC and its adsorption capacity was greatly promoted due to the presence of humic acid, CO₃^2- ion and weakly alkaline environment. About complete degradation of TC could be completed within 60 min under suitable conditions. A significant improvement of catalyst rate was observed after the addition of CO₃^2- ion, because of the selective degradation of CO₃^•- to TC. BET, XPS and FT-IR analysis indicated that the mechanisms of TC uptake can be ascribed to pore-filling, H-bonds and complexation. Radical trapping experiments showed that ¹O₂ should serve as predominant contributions, and SO₄^•- and •OH also played a role in the degradation process. This study provides some inspiration for the construction of 3D-CA-FC as a novel and promising bifunctional material for the elimination of contaminants in water treatment.

Multifunctional capacity of CoMnFe-LDH/LDO activated peroxymonosulfate for p-arsanilic acid removal and inorganic arsenic immobilization: Performance and surface-bound radical mechanism

Organoarsenic contaminants existing in water body threat human health and ecological environment due to insufficient bifunctional treatment technologies for organoarsenic degradation and inorganic arsenic immobilization. In order to safely and efficiently treat organoarsenic contaminants discharged into the aquatic environment, Co-Mn-Fe layered double hydroxide (CoMnFe-LDH) and Co-Mn-Fe layered double oxide (CoMnFe-LDO) were fabricated and employed as peroxymonosulfate (PMS) activator for organoarsenic degradation and inorganic arsenic immobilization, and p-arsanilic acid (p-ASA) was selected as target pollutant. Results demonstrated that the satisfactory removal of p-ASA (100.0%) in both CoMnFe-LDH/PMS and CoMnFe-LDO/PMS systems was obtained within 30 min, and substantial inorganic arsenic adsorption could be achieved (below 0.5 mg/L) in two systems with converting major inorganic arsenic species to arsenate. As XPS, ESR and quenching experiment revealed, the existence and generation of surface-bound radicals in two systems were identified. Based on density functional theory calculation and XPS analysis, the catalytic mechanism of CoMnFe-LDO/PMS system that PMS could be activated via direct electron transfer from adsorbed p-ASA was clarified, which differed from PMS activation via coupling with surface hydroxyl groups in CoMnFe-LDH/PMS system. Catalytic performance assessment under various critical operation parameters indicated that CoMnFe-LDH presented more stable ability of p-ASA removal in a wide pH range and complex aquatic environment. The recycle experiment demonstrated the excellent stability and reusability of CoMnFe-LDH(LDO). Besides, seven degradation products of p-ASA in CoMnFe-LDH/PMS system including phenolic compounds, azophenylarsonic acid, nitrobenzene and benzoquinne were identified by UV-Vis spectra and LC-TOF-MS analysis, and the corresponding degradation pathway was proposed. In summary, compared to CoMnFe-LDO/PMS, CoMnFe-LDH/PMS holds great promise for the development of an oxidation-adsorption process for efficient control of organoarsenic pollutant.

Preparation, characterization, and applications of Fe-based catalysts in advanced oxidation processes for organics removal: A review

Fe-based catalysts as low-cost, high-efficiency, and non-toxic materials display superior catalytic performances in activating hydrogen peroxide, persulfate (PS), peracetic acid (PAA), percarbonate (PC), and ozone to degrade organic contaminants in aqueous solutions. They mainly include ferrous salts, zero-valent iron, iron-metal composites, iron sulfides, iron oxyhydroxides, iron oxides, and supported iron-based catalysts, which have been widely applied in advanced oxidation processes (AOPs). However, there is lack of a comprehensive review systematically reporting their synthesis, characterization, and applications. It is imperative to evaluate the catalytic performances of various Fe-based catalysts in diverse AOPs systems and reveal the activation mechanisms of different oxidants by Fe-based catalysts. This work detailedly summarizes the synthesis methods and characterization technologies of Fe-based catalysts. This paper critically evaluates the catalytic performances of Fe-based catalysts in diverse AOPs systems. The effects of solution pH, reaction temperature, coexisting ions, oxidant concentration, catalyst dosage, and external energy on the degradation of organic contaminants in the Fe-based catalyst/oxidant systems and the stability of Fe-based catalysts are also discussed. The activation mechanisms of various oxidants and the degradation pathways of organic contaminants in the Fe-based catalyst/oxidant systems are revealed by a series of novel detection methods and characterization technologies. Future research prospects on the potential preparation means of Fe-based catalysts, practical applications, assistive technologies, and impact in AOPs are proposed.

Activation of Persulfate for Improved Naproxen Degradation Using FeCo2O4@g-C3N4 Heterojunction Photocatalysts

An effective heterojunction with robust charge separation and enormous degradation efficiency is the major task for photocatalyst preparation. In this study, we have prepared the FeCo2O4-loaded g-C3N4 nanosheet by the sol-gel-assisted calcination method for photo-Fenton-like degradation under visible-light irradiation by activating persulfate. The nanocomposite exhibits a higher charge separation efficiency than pure g-C3N4 and FeCo2O4 for the degradation reaction against naproxen drugs. An effective interaction between the nanoparticles increases the degradation efficiency up to 91% with a synergistic index of 73.62%. Moreover, the nanocomposite exhibits a 78% mineralization efficiency against the naproxen pollutant under visible-light irradiation. For practical implementation, the degradation reaction was tested with various pH values, different water sources (DI, lake, and tap water), and light sources (LED (visible)/direct sunlight (UV-visible)). Moreover, the possible degradation mechanism predicted by the elemental trapping experiment and the recycling experiment clearly revealed that the heterojunction composite has a high enough degradation stability.

Advanced Oxidation Processes Based on Sulfate Radicals for Wastewater Treatment: Research Trends

In this work, the recent trends in the application of the sulfate radical-based advanced oxidation processes (SR-AOPs) for the treatment of wastewater polluted with emerging contaminants (ECs) and pathogenic load were systematically studied due to the high oxidizing power ascribed to these technologies. Additionally, because of the economic benefits and the synergies presented in terms of efficiency in ECs degradation and pathogen inactivation, the combination of the referred to AOPs and conventional treatments, including biological processes, was covered. Finally, the barriers and limitations related to the implementation of SR-AOPs were described, highlighting the still scarce full-scale implementation and the high operating-costs associated, especially when solar energy cannot be used in the oxidation systems.

Thiourea-assisted one-step fabrication of a novel nitrogen and sulfur co-doped biochar from nanocellulose as metal-free catalyst for efficient activation of peroxymonosulfate

The N, S co-doped biochar (N, S-BC) with multistage pore structure was successfully synthesized from nanocellulose and thiourea by one-step pyrolysis, which could effectively activate peroxymonosulfate (PMS) to degrade sulfamethoxazole (SMX) in water. Moreover, the removal efficiency of SMX by this oxidation system was 2.3-3.1 times than that of other systems activated by common metal oxides (such as Fe₃O₄、Fe₂O₃, and MnO₂). More importantly, the mechanism of the N, S-BC/PMS process was deduced by reactive oxygen species (ROS) quenching experiment and electron paramagnetic resonance (EPR) test, which exhibited that surface-bound free radicals and singlet oxygen (¹O₂) played an essential role in the SMX degradation. Surprisingly, the sulfate radical (SO₄^•-) and hydroxyl radical (^•OH) produced in this system existed in a bound state on the surface of the carbon catalyst to react with SMX, rather than dispersed in the aqueous solution. This particular form of free radicals could resist the influence of background substances and pH changes in water, and maintain excellent SMX degradation efficiency under different water matrices and pH. This study provides a new insight into the application of carbon catalyst in actual water pollution control.

Advances in Electrochemical and Catalytic Performance of Nanostructured FeCo2 O4 and Its Composites

It is well established that the excessive and uncontrolled use of fossil fuels and organic chemicals have put a risk to the earth's environment and the life that sustains within it. Carbon-free, sustainable, alternative energy technologies have therefore become the prime focus of current research. Smart inorganic materials have emerged as the potential solution to suffice energy needs and remediate the organic pollutants discharged to the environment. One such promising, versatile material is FeCo₂ O₄ which has gained immense research interest in the present decade due to its high efficiency and performance in energy and environmental applications. Innovative material design strategies involving the interplay of nanostructured morphology, chemical composition, redox surface states, and defect engineering have significantly enhanced both electrochemical and catalytic properties of FeCo₂ O₄ . Therefore, this review article aims to provide the first-ever comprehensive account of the latest research and developments in design-synthesis strategies, characterization techniques, and applications of nanostructured FeCo₂ O₄ and its composites in various electrochemical as well as catalytic applications. A detailed account of the nanostructured FeCo₂ O₄ and its composites in various energy storage and conversion devices such as supercapacitors (SCs), batteries, and fuel cells has been presented. Furthermore, a special section has been devoted to highlight the role of FeCo₂ O₄ in enhancing the sluggish reaction kinetics of oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) in water splitting application. This review also highlights the role of nanostructured FeCo₂ O₄ in photocatalytic waste water treatment, gas sensing, and dual-phase membrane technologies wherein FeCo₂ O₄ has demonstrated promising performance.

Sunlight-driven activation of peroxymonosulfate by microwave synthesized ternary MoO3/Bi2O3/g-C3N4 heterostructures for boosting tetracycline hydrochloride degradation

Design of direct Z-scheme heterojunction photocatalyst is considered as an effective strategy to fully use the high redox potential photogenerated charge carriers. This work reports a novel method for investigating the photosynergistic performance of the Z-scheme MoO₃/Bi₂O₃/g-C₃N₄ (MBG) photocatalyst with peroxymonosulfate (PMS) for the solar degradation of tetracycline hydrochloride (TCH), a model of organic pollutants in wastewater. The results showed a better strategy to activate PMS via accelerating the redox cycle (Mo⁶⁺/Mo⁵⁺), which ultimately induces the successive generation of highly reactive oxygen species. The effect of dosage of the catalyst, PMS, pH of the solution, initial concentrations of TCH and the presence of inorganic anions were investigated. It was found that the degradation of the TCH under sunlight irradiation (SL) was strongly enhanced by the presence of the PMS as an electron acceptor. The MBG/PMS/SL system was able to degrade an initial concentration (40 mg/L) of the TCH solution within 140 min. The good reusability and stability of the MBG catalyst were evaluated by recycling the degradation experiment. The main free radicals are OH and SO₄^─ which played an important role in the degradation reaction were identified by scavenger experiments and confirmed by EPR spectroscopy. X-ray photoelectron spectroscopy (XPS) study revealed the role of molybdenum ion in the activation process of PMS. The possible synergistic degradation reaction mechanism was proposed.

The adsorption characteristics and mechanism of montmorillonite with different layer charge density for alkyl ammonium with different carbon chain length

The crystal chemical properties of montmorillonite and the length and amount of straight alkyl ammonium chain affect the adsorption characteristics of alkyl ammonium on montmorillonite.