Determination of very volatile organic compounds in water samples by purge and trap analysis with a needle-type extraction device

Dynamic extraction of residual solvents from pharmaceutical formulations using a needle-type extraction device

This study developed a rapid screening method to determine residual solvents contained in a tablet formulation using a needle-type extraction device. For this, the tablet formulation was pulverized and the powdered sample was rapidly inserted into a pipette tip. After fixing the sample with quartz wool, the pipette tip was capped with a silicon septum. A needle-type extraction device packed with Carbopack X and a carbon molecular sieve was inserted into the pipette tip through the septum, and the gas sample was collected. During this gas sampling, pure N2 gas was introduced into the pipette tip. The extraction time for collecting 100 mL of the sample was approximately 10 min. After gas sampling, the extraction needle was connected to a gas-tight syringe and 0.5 mL of pure N2 gas (desorption gas) was collected. The extraction needle was then inserted into a heated gas chromatographic injection port. The extracted residual solvents were then thermally desorbed and determined using a gas chromatograph-flame ionization detector. The detector response is very low for carbon tetrachloride, although the proposed method showed sufficient sensitivity for five Class 1 compounds. Additionally, this study clearly indicated that the purge efficiency of residual solves with dynamic extraction is different between powdered pharmaceutical formulations.

Needle trap device technique: From fabrication to sampling

Needle Trap Device (NTD) as a novel, versatile, and eco-friendly technique has played an important role in analytical and environmental chemistry. The distinctive role of this interdisciplinary technique can be defended through the sampling and analysis of biological samples and industrial pollutants in gaseous and liquid environments. In recent years, significant efforts have been made to enhance the performance of the needle trap device resulting in the development of novel extraction routes by various packing materials with improved selectivity and enhanced adsorption characteristics. These achievements can lead to the facilitated pre-concentration of desired analytes. This review tries to have a comparative and comprehensive survey of the three important areas of NTD technique: I) Fabrication and preparation procedures of NTDs; II) Sampling techniques of pollutants using NTDs; and III) Employed materials as adsorbents in NTDs. In the packing-material section, the commercial and synthetic adsorbents such as carbon materials, metal-organic frameworks, aerogel, and polymers are considered. Furthermore, the limitations and potential areas for future development of the NTD technique are presented.

Comparative analysis of very volatile organic compounds and odors released from decorative medium density fiberboard using gas chromatography-mass spectrometry and olfactory detection

VVOCs with a retention range below C₆ have become one of the main indoor pollutants that negatively affect human health. Most studies have focused on the emission of VOCs from furniture and decorative materials, seldom consider VVOCs. To close this gap, a 15-L environmental chamber, combined with multi-absorbent tube, was used for gas sampling. Emissions of VVOCs and odors released from decorative medium density fiberboard (MDF) were measured using gas chromatography-mass spectrometry and olfactometry detection. The results demonstrated that multi-absorbent tubes had excellent capture capacity for low-molecular-weight VVOCs. Thickness and decorative materials had conspicuous effects on VVOCs and odor emissions. The total VVOCs (TVVOC) from 18-mm decorative MDF was consistently higher than that of 8-mm samples. The major VVOCs from these decorative MDF were alcohols, esters and ketones, which were the major odor contributors with high odor intensity values. VVOCs concentration generally increased as thickness increased, but it decreased after decorative treatment. Fruity and alcohol-like were the main odor impressions of 8-mm MDF, whereas sweet and fruity were the major odor impressions of 8-mm polyvinyl chloride decorative MDF (PVC-MDF) and melamine impregnated paper decorative MDF (MI-MDF). Fruity was the main odor impression of 18-mm decorative MDF. The overall odor intensity increased and the major odor impression may differ when thickness was changed. Both the MI and the PVC decorative materials blocked some odor emissions but did so to a greater extent with the former than with the latter. Identification and analysis of the composition of VVOCs can supplement a database structure network of volatile pollutants and establish a novel and feasible method to investigate low-molecular-weight substances from wooden materials and their products.

Urinary bio-monitoring of amphetamine derivatives by needle trap device packed with the zirconium-based metal-organic framework

In this research, zirconium-based metal–organic framework was utilized as a novel and efficient porous adsorbent for headspace extraction of Amphetamine, Methamphetamine, and Fenfluramine from the urine samples by a needle trap device (NTD). The Zr-UiO-66-PDC was electrosynthesized at the green conditions and characterized by various analyses such as FT-IR, XRD, FE-SEM, EDS, and elemental mapping techniques. Then, the effective parameters on the NTD efficiency such as salt content, pH, extraction/desorption temperature and time were evaluated and optimized by response surface methodology. The optimal extraction of amphetamine compounds was accomplished in 50 min at 70 ºC at the situation with NaCl content of 27% and pH: 11.90. The limit of detection, and limit of quantification factors were determined to be 0.06–0.09 and 0.5–0.8 ng mL⁻¹, respectively. Furthermore, the precision and accuracy (intra- and inter-day) of the employed procedure in the term of relative standard deviation (RSD) were calculated in the range of 8.0–9.0% and 6.8–9.8%, respectively. Also, the recovery percent of the extracted analytes were concluded in the range of 95.0–97.0% after 10 days from the sampling and storage at 4 °C. Finally, the proposed procedure was involved in the analysis of amphetamine compounds in the real urine samples. These results were proved the proposed Zr-UiO-66-PDC@HS-NTD technique coupled with GC-FID can be used as an eco-friendly, fast-response, sensitive, and efficient drug test procedure for trace analysis of the amphetamine compounds in urine samples.

Volatile organic compounds: A proinflammatory activator in autoimmune diseases

The etiopathogenesis of inflammatory and autoimmune diseases, including pulmonary disease, atherosclerosis, and rheumatoid arthritis, has been linked to human exposure to volatile organic compounds (VOC) present in the environment. Chronic inflammation due to immune breakdown and malfunctioning of the immune system has been projected to play a major role in the initiation and progression of autoimmune disorders. Macrophages, major phagocytes involved in the regulation of chronic inflammation, are a major target of VOC. Excessive and prolonged activation of immune cells (T and B lymphocytes) and overexpression of the master pro-inflammatory constituents [cytokine and tumor necrosis factor-alpha, together with other mediators (interleukin-6, interleukin-1, and interferon-gamma)] have been shown to play a central role in the pathogenesis of autoimmune inflammatory responses. The function and efficiency of the immune system resulting in immunostimulation and immunosuppression are a result of exogenous and endogenous factors. An autoimmune disorder is a by-product of the overproduction of these inflammatory mediators. Additionally, an excess of these toxicants helps in promoting autoimmunity through alterations in DNA methylation in CD4 T cells. The purpose of this review is to shed light on the possible role of VOC exposure in the onset and progression of autoimmune diseases.

The formation, analysis, and control of chlor(am)ination-derived odor problems: A review

Odors and tastes have become universal problems related to drinking water quality. In addition to the typical odor problems caused by algae or microorganisms, the occurrence of odors derived from drinking water disinfection have attracted attention. The chlor(am)ination-derived odor substances have certain toxicity and odor-causing characteristics, and would enter the tap water through water distribution systems, directly affecting drinking water safety and customer experience. This study provided a comprehensive overview of the occurrence, detection, and control of odor substances derived from drinking water chlor(am)ination disinfection. The occurrence and formation mechanisms of several typical types of disinfection derived odor substances were summarized, including haloanisoles, N-chloroaldimines, iodotrihalomethanes, and halophenoles. They are mainly derived from specific precursors such as halophenols, anisoles, and amino acids species during the disinfection or distribution networks. In addition, the change of disinfectant during chlor(am)ination was also one of the causes of disinfection odors. Due to the extremely low odor threshold concentrations (OTCs) of these odor substances, the effective sample pre-enrichment for instrument identification and quantification are essential. The control strategies of odor problems mainly include adsorption, chemical oxidation, and combined processes such as ozonation and biological activated carbon processes (O₃/BAC) and ultraviolet-based advanced oxidation processes (UV-AOPs). Finally, the challenges and possible future research directions in this research field were discussed and proposed.

Nano-hydroxyapatite/polyaniline composite as an efficient sorbent for sensitive determination of the polycyclic aromatic hydrocarbons in air by a needle trap device

Hydroxyapatite is a readily available, inexpensive, environmentally friendly adsorbent with high adsorption capacity. In this study, a polyaniline-doped nano-hydroxyapatite (PANI@HA) adsorbent was synthesized and employed in a needle trap device for the extraction of polycyclic aromatic hydrocarbons such as naphthalene, fluoranthene, benzo[a]anthracene, phenanthrene, and benzo[a]pyrene for the first time. The synthesized adsorbent was characterized by X-ray diffraction, field emission scanning electron microscopy, and Fourier-transform infrared spectroscopy analysis. Initially, effective variables such as the carryover effect, storage time, accuracy, and precision of the method were examined in the laboratory. The desorption conditions were optimized using the response surface methodology and central composite design methods. From the standpoint of quantitative parameters, the limit of detection and limit of quantitation were determined to be between 0.001 and 0.003 and 0.021 and 0.051 ng mL-1, respectively, which indicates the high sensitivity of the proposed method. Additionally, no significant changes were detected after storage of analytes inside the needle at 4 °C after 60 days. The results of this study also provide a high correlation between the results of sampling with needles containing PANI@HA and with XAD-2 adsorbent tubes (standard NIOSH 5115 method) (R 2 = 0.98). Finally, the proposed method was successfully employed in the extraction and determination of polycyclic aromatic hydrocarbons in field (real) samples. In general, it can be concluded that a needle packed with PANI@HA is a reliable and high-performance method for sampling polycyclic aromatic hydrocarbons compared to the NIOSH method.

The geometrical characteristics of nickel-based metal organic framework on its entrapment capability

Here, a three dimensional nickel-based metal organic framework (MOF) was synthesized via solvothermal and room temperature protocols. In order to study the effects of the synthesis conditions on the physical properties such as pore sizes and shapes of the prepared MOFs, their extraction capabilities were examined. Both MOFs were characterized by Fourier transform infrared spectroscopy, powder X-ray diffraction, scanning electron microscopy, Brunauer-Emmett-Teller and thermogravimetric analyses. Brilliant properties such as porous structure, high surface area and considerable thermal stability make them reasonable candidates to be employed as efficient extractive phases. The efficiency of the superior nickel-based MOF was evaluated for headspace needle trap extraction of chlorobenzenes as model compounds in conjunction with gas chromatography-mass spectrometry (GC-MS). The MOF-based extractive phase was conveniently packed in a needle trap device and after extraction, the desorption process was performed via direct insertion of needle into the GC inlet. After optimizing the extraction/desorption conditions, the figures of merit such as linear dynamic range was in the range of 5-1000 ng L^-1 (R² > 0.987) while the limits of detection and quantification values were 2-10 and 6-30 ng L^-1, respectively. The intra- and inter-day relative standard deviations for three replicates at the concentration level of 50 ng L^-1 were in the range of 7-9% and 9-12%, respectively. The needle-to-needle reproducibility was also found to be in the range of 5-11%. Acceptable relative recovery values at the concentration level of 50 ng L^-1 ranged from 85 to 96%, showing no significant matrix effect.

Non-targeted screening and analysis of volatile organic compounds in drinking water by DLLME with GC-MS

Volatile organic compounds (VOCs) in drinking water may potentially be hazardous. We developed a novel non-targeted analysis method of VOCs in drinking water that uses dispersive liquid-liquid microextraction coupled with gas chromatography-mass spectrometry. Analysis parameters were selected from range-finding tests on the peak number and average area of the extracted compounds. The optimized method was applied to analyze VOCs in tap water samples collected from Wuhan City, China. Twenty-seven compounds with high match degrees and a high prevalence were selected for quantification and evaluation. We used structure-activity relationships to predict the carcinogenicity of these compounds. Although most of the compounds were non-toxic, compounds such as dibutyl phthalate and diacetone alcohol should be investigated further. Untargeted analysis of the tap water samples identified 75-200 VOCs, including 67 highly prevalent compounds. Industrial and pharmaceutical chemicals accounted for approximately 70% of the VOCs in the samples. This method of non-targeted analysis and in silico toxicity prediction is simple and economic, and could be used in screening VOCs in drinking water.

Purge-and-trap Determination of Ammonia in Water Samples Using Needle-type Extraction Coupled with Gas Chromatography-Barrier Discharge Ionization Detection

This manuscript describes the determination of ammonia (NH₃) in aqueous samples by purge-and-trap extraction using a needle-type extraction device with gas chromatography-barrier discharge ionization detector (GC-BID). NH₃ was purged from the aqueous samples in basic conditions and then salted out with sodium chloride. Purged ammonia was trapped onto non-volatile carboxylic acid-coated macroporous terephthalic acid particles, which were contained within the needle-type extraction device. The analyte (NH₃) was thermally desorbed by heating the extraction needle in the GC injection port, and detected by BID. After the optimization of both purge and extraction conditions, the linearity and sensitivity of the proposed method were evaluated. The limit of detection was found to be 2.0 mg L^-1 at a headspace sampling volume of 100 mL. The method applicability was confirmed by the determination of spiked NH₃ in tap water and river water samples.

Flavor formation in different production steps during the processing of cold-smoked Spanish mackerel

This study aimed to determine the changes in the flavor profile during different operating units when making cold-smoked Spanish mackerel. Sensory evaluation and instrumental analysis of tenderness were applied to optimize the processing parameters. For the overall odor perception, distinct odor among fresh and processed samples could be distinguished using electronic nose (e-Nose). Purge-and-trap (P&T) extraction combined with gas chromatography-mass spectrometry (GC-MS) was used to identify volatile compounds. Alcohols were the major volatiles in Spanish mackerel over the whole processing, while 2-butanol was found in the highest concentration. Curing was an effective way to remove fishy odor. Drying decreased the concentration of volatiles, especially sulfur compounds. Odor formation in cold-smoked mackerel could be divided into four steps (curing, drying, cold smoking and heating) as a result of partial least squares discriminant analysis (PLS-DA).

Measurement of volatile organic compounds and associated risk assessments through ingestion and dermal routes in Dongjiang Lake, China

This study aims to investigate the occurrence, distribution and risk assessment of volatile organic compounds (VOCs) in Dongjiang Lake of China. Twenty two kinds of VOCs were detected, and the major VOCs were alkene compounds. The total concentration of VOCs (∑VOCs) ranged from 2.93 to 4.69 µg/L, and none of the VOCs detected in Dongjiang Lake exceeded the concentration limits set in the National Drinking Water Quality Standards (GB5749-2006) or the National Environmental Quality Standards for Surface Water (GB3838-2002) of China. Risk quotients (RQ) model, Multimedia Environment Pollutant Assessment System (MEPAS) and value of odor hazard index (OHI) were used to assess the ecological risk, lifetime carcinogenic risk and olfactory risk of VOCs in Dongjiang Lake, respectively. The RQ_total values varied from 3.95 × 10^-3 to 0.34 and the RQ values for all the 22 detected VOCs in 12 sample locations of Dongjiang Lake were below 0.01, which means negligible risk to aquatic organisms. The cancerous and non-cancerous risk indices were in the range of 2.31 × 10^-9-5.16 × 10^-7 and 1.68 × 10^-7-1.45 × 10^-2, respectively. Bromodichloromethane and 1,1-dichloroethene were associated with the highest and lowest carcinogenic risks in all 12 sample locations. Results also demonstrated that the olfactory risk in Dongjiang Lake is negligible. These data suggest that the VOCs in Dongjiang Lake may not lead great ecological and health risks for organism and human.

Analysis of formaldehyde and acrolein in the aqueous samples using a novel needle trap device containing nanoporous silica aerogel sorbent

In this research, a needle trap device (NTD) packed with nanoporous silica aerogel as a sorbent was used as a new technique for sampling and analysis of formaldehyde and acrolein compounds in aqueous and urine samples. The obtained results were compared with those of the commercial sorbent Carboxen1000. Active sampling was used and a 21-G needle was applied for extraction of gas in the sample headspace. The optimization of experimental parameters like salt addition, temperature and desorption time was done and the performance of the NTD for the extraction of the compounds was evaluated. The optimum temperature and time of desorption were 280 °C and 2 min, respectively. The ranges of limit of detection, limit of quantification and relative standard deviation (RSD) were 0.01-0.03 μg L^-1, 0.03-0.1 μg L^-1 and 2.8-7.3%, respectively. It was found that the NTD containing nanoporous silica aerogel had a better performance. Thus, this technique can be applied as an effective and reliable method for sampling and analysis of aldehyde compounds from different biological matrices like urine, exhalation and so on.

Needle Trap Device as a New Sampling and Preconcentration Approach for Volatile Organic Compounds of Herbal Medicines and its Application to the Analysis of Volatile Components in Viola tianschanica

INTRODUCTION

The needle trap device (NTD) technique is a new microextraction method for sampling and preconcentration of volatile organic compounds (VOCs). Previous NTD studies predominantly focused on analysis of environmental volatile compounds in the gaseous and liquid phases. Little work has been done on its potential application in biological samples and no work has been reported on analysis of bioactive compounds in essential oils from herbal medicines.

OBJECTIVE

The main purpose of the present study is to develop a NTD sampling method for profiling VOCs in biological samples using herbal medicines as a case study.

METHODOLOGY

A combined method of NTD sample preparation and gas chromatography-mass spectrometry was developed for qualitative analysis of VOCs in Viola tianschanica. A 22-gauge stainless steel, triple-bed needle packed with Tenax, Carbopack X and Carboxen 1000 sorbents was used for analysis of VOCs in the herb. Furthermore, different parameters affecting the extraction efficiency and capacity were studied.

RESULTS

The peak capacity obtained by NTDs was 104, more efficient than those of the static headspace (46) and hydrodistillation (93). This NTD method shows potential to trap a wide range of VOCs including the lower and higher volatile components, while the static headspace and hydrodistillation only detects lower volatile components, and semi-volatile and higher volatile components, respectively.

CONCLUSION

The developed NTD sample preparation method is a more rapid, simpler, convenient, and sensitive extraction/desorption technique for analysis of VOCs in herbal medicines than the conventional methods such as static headspace and hydrodistillation. Copyright © 2016 John Wiley & Sons, Ltd.