Water-compatible temperature and magnetic dual-responsive molecularly imprinted polymers for recognition and extraction of bisphenol A

Fabrication and properties of temperature-responsive imprinted sensors based on fluorescently labeled yeast cells via MVL ATRP

Temperature-responsive yeast cell-imprinted sensors (CIPs/AuNPs/Ti3C2Tx/AuNPs/Au) were prepared based on fluorescein isothiocyanate labeled yeast cells (FITC-yeast) via metal-free visible-light-induced atom transfer radical polymerization (MVL ATRP). Here, N-isopropyl acrylamide (NIPAM) was used as a temperature-responsive functional monomer, α-methacrylic acid (MAA) was chosen as an auxiliary functional monomer, N,N'-methylene bisacrylamide (MBA) was used as a cross-linker, and FITC-yeast was selected as both a template and photocatalyst. Under the optimal conditions, the detection range of the yeast cell-imprinted sensor toward yeast cells was 1.0 × 102 to 1.0 × 109 cells per mL, and the detection limit was 11 cells per mL (S/N = 3), with a linear equation of ΔI (μA) = 8.44 log[C (cells per mL)] + 7.62 (R2 = 0.993). The sensor showed good selective recognition in the presence of interfering substances such as autolyzed yeast cells (AY), dead yeast cells (DY), human mammary epithelial cells (MCF-10A), human breast cancer cells (MCF-7) and Escherichia coli (EC). The sensor also had good consistency and reproducibility. Finally, spiked recovery experiments were performed to investigate the recognition of yeast cells in the actual sample using the yeast cell-imprinted sensor. The spiked recoveries were all in the range of 98.5-108.0%, and the RSD values were all less than 4%, indicating that the sensor had good application prospects.

Magnetic surface-imprinted polymer microspheres coupled with HPLC-MS/MS for sensitive detection of amphetamine-type drugs in water

Magnetic surface imprinted polymer microspheres (Fe3O4@MIPs) were successfully synthesized via Pickering emulsion polymerization, utilizing N-Methylphenethylamine as a surrogate template for amphetamine-type drugs. Fe3O4@MIPs not only possessed excellent dispersibility and enough magnetic properties in aqueous solutions, but also displayed good selectivity towards six amphetamines, with an imprinting factor ranging from 1.8 to 2.6. The adsorption kinetics closely aligned with the pseudo-second-order model, and the adsorption efficiency exceeds 80 % for each amphetamine at equilibrium. Fe3O4@MIPs were then employed as the efficient adsorbents for the extraction of amphetamine drugs. Extraction parameters, including sample pH, the mass of adsorbent, and the type and volume of eluting solvent, were carefully optimized. In combination with the high performance liquid chromatography tandem triple quadrupole mass spectrometry (HPLC-MS/MS), a selective magnetic solid-phase extraction (MISPE) method utilizing Fe3O4@MIPs was developed for the detection of six amphetamines in water samples. The limits of detection and limits of quantitation were determined to be 5.2∼23 ng L-1 and 17∼77 ng L-1, respectively. Recoveries for the six target drugs from lake water and sewage samples fell within the range of 87.2∼110 %. Additionally, the MISPE-HPLC-MS/MS method exhibited excellent repeatability, with a precision below 8.5 % at two spiking levels. The prepared Fe3O4@MIPs possessed the advantages of high selectivity, straightforward preparation, facile separation and good reusability, and was highly suitable for the efficient extraction of amphetamine-type substances in complex environmental water.

Fabrication of magnetic hydrophilic imprinted polymers via two-step immobilization approach for targeted detecting bisphenol A

Molecularly imprinted polymer with water-compatibility for effective separation and enrichment of targeted trace pollutants from complicated matrix has captured extensive attention in terms of their high selectivity and matrix compatibility. This study focuses on modified β-cyclodextrin is used as a hydrophilic functional monomer to develop magnetic molecularly imprinted polymers (MMIPs). MMIPs were prepared using Fe3O4 nanoparticles as carriers and bisphenol A (BPA) as templates using a two-step fixation strategy and surface imprinting technology. The structural characteristic and binding properties of the prepared MMIPs were thoroughly studied. The MMIPs exhibited high crystallinity, high adsorption capacity, fast rebinding rate, remarkable selectivity and distinguish reusability. In addition, through magnetic solid-phase extraction separation technology and high-performance liquid chromatography ultraviolet quantitative detection technology, MMIPs are used for selective enrichment and detection of BPA in complex media such as environmental water and milk. This work provides a new route to construct the hydrophilic molecularly imprinted materials and a new sight on developing more effective sample pretreatment strategies for monitoring targeted pollution in complicated aqueous media.

Computational design and preparation of water-compatible noncovalent imprinted microspheres

Herein, 2,4-dichlorophenoxyacetic acid (2,4-D) was used as a model template in a rational design strategy to produce water-compatible noncovalent imprinted microspheres. The proposed approach involved computational modelling for screening functional monomers and a simple method for preparing monodisperse and highly cross-linked microspheres. The fabricated non-imprinted polymer (NIP) and 2,4-d-imprinted polymer (2,4-d-MIP) were characterised, and their adsorption capabilities in an aqueous environment were evaluated. Results reveal that the pseudo-second-order kinetics model was appropriate for representing the adsorption of 2,4-D on NIP and 2,4-d-MIP, with R2 values of 0.97 and 0.99, respectively. The amount of 2,4-D adsorbed on 2,4-d-MIP (97.75 mg g-1) was considerably higher than those of phenoxyacetic acid (35.77 mg g-1), chlorogenic acid (9.72 mg g-1), spiramycin (1.56 mg g-1) and tylosin (1.67 mg g-1). Furthermore, it exhibited strong resistance to protein adsorption in an aqueous medium. These findings confirmed the feasibility of the proposed approach, providing a reference for the development of water-compatible noncovalent imprinted polymers.

Dispersive micro solid phase extraction of glibenclamide from plasma, urine, and wastewater using a magnetic molecularly imprinted polymer followed by its determination by a high-performance liquid chromatography-photodiode array detector

The present study describes the development of a simple and selective analytical method for dispersive micro solid phase extraction and determination of glibenclamide (GLB) using magnetic molecularly imprinted polymer (MMIP) as a sorbent. MMIP was fabricated by the non-covalent method on the surface of silicated Fe3O4 and had a high affinity for glibenclamide; dual monomers, itaconic acid and allylamine, were used for this. Polymerization was achieved by the precipitation method in the presence of glibenclamide as the template and ethylene glycol dimethacrylate as the cross-linker. The morphology and structural properties of the MMIP were characterized by different analytical methods. To achieve maximum extraction efficiency, influencing parameters were optimized. The linearity range was 1-2000 and 12-2000 μg L-1 by high-performance liquid chromatography-photodiode array detector (HPLC-PDA) and UV-vis spectroscopy, respectively. The detection and quantification limits with UV-vis and HPLC-PDA analyses were 4 and 12 μg L-1 and 0.3 and 1 μg L-1, respectively. Under optimized conditions, recovery of glibenclamide spiked in plasma, human urine, and wastewater was between 89.4 and 102.9% at the concentration levels of 25, 250, and 500 μg L-1; relative standard deviations were below 3.7% by HPLC-PDA. The developed method has a favorable pre-concentration factor of 140.0. Equilibrium data and sorption isotherms fitted well with the Langmuir model. A maximum sorption capacity of 24.260 mg g-1 was acquired based on the Langmuir model. The synthesized sorbent with high selectivity was used to separate GLB from complex biological systems and wastewater before measurement with UV-vis or HPLC-PDA.

Designing Molecularly Imprinted Polymer-Modified Boron-Doped Diamond Electrodes for Highly Selective Electrochemical Drug Sensors

Drug detection in biological solutions is essential in studying the pharmacokinetics of the body. Electrochemical detection is an accurate and rapid method, but measuring multiple drugs that react at similar potentials is challenging. Herein, we developed an electrochemical sensor using a boron-doped diamond (BDD) electrode modified with a molecularly imprinted polymer (MIP) to provide specificity in drug sensing. The MIP is a polymer material designed to recognize and capture template molecules, enabling the selective detection of target molecules. In this study, we selected the anticancer drug doxorubicin (DOX) as the template molecule. In the electrochemical measurements using an unmodified BDD, the DOX reduction was observed at approximately -0.5 V (vs Ag/AgCl). Other drugs, i.e., mitomycin C or clonazepam (CZP), also underwent a reduction reaction at a similar potential to that of DOX, when using the unmodified BDD, which rendered the accurate quantification of DOX in a mixture challenging. Similar measurements conducted in PBS using the MIP-BDD only resulted in a DOX reduction current, with no reduction reaction observed in the presence of mitomycin C and CZP. These results suggest that the MIP, whose template molecule is DOX, inhibits the reduction of other drugs on the electrode surface. Selective DOX measurement using the MIP-BDD was also possible in human plasma, and the respective limits of detection of DOX in PBS and human plasma were 32.10 and 16.61 nM. The MIP-BDD was durable for use in six repeated measurements, and MIP-BDD may be applicable as an electrochemical sensor for application in therapeutic drug monitoring.

Magnetic molecularly-imprinted microspheres with a core-shell structure for the extraction of catalpol from both Rehmannia glutinosa Libosch and biological samples

We report on the successful development of a magnetic molecularly imprinted polymer (MMIP) for the separation and detection of catalpol in Rehmannia glutinosa extract and biological samples. Catalpol was used as the template molecule for the MMIPs, which were synthesized using the reverse prediction approach and differential UV-visible spectra to optimize the synthesis conditions. The resulting MMIPs were characterized using techniques including scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, and vibrating sample magnetometry, which confirmed their excellent nuclear shell construction and simple rapid magnetic separation. Static and dynamic adsorption experiments were performed to assess the sensitivity, repeatability, and adsorption capacity of the MMIPs. Adsorption capacity was found to be high (59.09 µg/mg). The MMIPs also exhibited strong identification specificity for catalpol analogs (IF = 2.41). Magnetic solid phase extraction (MSPE) was optimized to establish an MSPE-HPLC approach based on the MMIPs. Under ideal conditions, the new method showed excellent determination coefficient (R2 > 0.99) in the ranges of 0.1-1.0 mg/mL and 0.03-0.18 mg/mL for R. glutinosa extract and biological material, respectively, with limits of detection of 5.4 ng/mL and 1.7 ng/mL. The novelty of this research lies in the preparation of magnetic surface MMIPs using a magnetic carrier. These MMIPs exhibit excellent magnetic properties and possess specific adsorption capability for catalpol, enabling rapid separation. They offer advantages such as low cost, high specificity, chemical stability, physical robustness, and recyclability (97.09%-106.53%, 91.32%-100.99%). The application of these polymers in the pretreatment method for determining the catalpol content in R. glutinosa extract and biological samples enhances the extraction efficiency and detection accuracy for catalpol. It eliminates interference and influences from other components in catalpol determination while exhibiting high sensitivity, good enrichment effects, excellent reusability, and a high recovery rate.

Analytical approaches for screening of per- and poly fluoroalkyl substances in food items: A review of recent advances and improvements

Per and polyfluoroalkyl substances (PFAS) are a group of man-made chemicals characterized by their ubiquitous nature in all environmental compartments which makes them of increasing concern due to their persistence, bioaccumulation, and toxicity (PBT). Several instrumental methodologies and separation techniques have been identified in the literature for the detection and quantification of PFAS in environmental samples. In this review, we have identified and compared common separation techniques adopted for the extraction of PFAS in food items, and analytical methodologies for identification and quantification of PFAS in food items of plant and animal origin, highlighting recent advances in tandem techniques for the high selectivity and separation of PFAS related compounds as well as knowledge gaps and research needs on current analytical methodologies.

Novel detection method to rapidly quantify toxic cucurbitacin in Lagenaria siceraria (bottle gourd)

Bottle gourd (Lagenaria siceraria) is widely used in India for its medicinal properties. Sometimes its consumption as a fruit or juice can lead to serious health issues due to the presence of toxic cucurbitacins (Cuc) like Cuc B at high concentration. In the present study, a molecularly imprinted polymer (MIP) based method was developed to quantify Cuc B in commercial bottle gourd juice. Cuc B quantification was also done in peel and pulp of fresh bottle gourd fruit. Developed MIP was superior to NIP (non-imprinted polymer) in terms of equilibrium binding, solid-phase extraction, selectivity, and loading capacity of Cuc B. Scatchard plot analysis, adsorption kinetics, and surface area study further strengthen the fact that prepared imprinted polymer was better than NIP for Cuc extraction. TLC and high-resolution LC-MS based analysis revealed that MIP selectively extracts Cuc B from all the studied samples. It was further observed that gamma irradiation and β-glucosidase treatment did not have any significant (p > 0.05) effect on Cuc concentration. The quantity of Cuc in 100 g of juice, peel, and pulp was 2.81 ± 0.26, 3.37 ± 0.31, and 2.39 ± 0.21 mg, respectively. Analytical method validation indicates that the MIP based method was highly linear, precise, and accurate to rapidly quantify toxic Cuc B in bottle gourd consequently assuring its quality.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13197-022-05600-3.

Applications of Molecular Imprinting Technology in the Study of Traditional Chinese Medicine

Traditional Chinese medicine (TCM) is one of the most internationally competitive industries. In the context of TCM modernization and internationalization, TCM-related research studies have entered a fast track of development. At the same time, research of TCM is also faced with challenges, such as matrix complexity, component diversity and low level of active components. As an interdisciplinary technology, molecular imprinting technology (MIT) has gained popularity in TCM study, owing to the produced molecularly imprinted polymers (MIPs) possessing the unique features of structure predictability, recognition specificity and application universality, as well as physical robustness, thermal stability, low cost and easy preparation. Herein, we comprehensively review the recent advances of MIT for TCM studies since 2017, focusing on two main aspects including extraction/separation and purification and detection of active components, and identification analysis of hazardous components. The fundamentals of MIT are briefly outlined and emerging preparation techniques for MIPs applied in TCM are highlighted, such as surface imprinting, nanoimprinting and multitemplate and multifunctional monomer imprinting. Then, applications of MIPs in common active components research including flavonoids, alkaloids, terpenoids, glycosides and polyphenols, etc. are respectively summarized, followed by screening and enantioseparation. Related identification detection of hazardous components from TCM itself, illegal addition, or pollution residues (e.g., heavy metals, pesticides) are discussed. Moreover, the applications of MIT in new formulation of TCM, chiral drug resolution and detection of growing environment are summarized. Finally, we propose some issues still to be solved and future research directions to be expected of MIT for TCM studies.

Synthesis of nitrogen-rich magnetic hypercrosslinked polymer as robust adsorbent for the detection of neonicotinoids in honey, tomatoes, lettuce and Chinese cabbage

In this study, a novel nitrogen-rich magnetic hypercrosslinked polymer (Fe3O4@Ph-HCP) was fabricated via a facile one-pot reaction of 1,3,5-triphenylbenzene, 2,4-dichloropyrimidine and phenyl-functionalized magnetic Fe3O4 nanoparticles. The Fe3O4@Ph-HCP possessed high specific surface, abundant nanopores and good stability. Especially, Fe3O4@Ph-HCP exhibited excellent adsorption capability with fast adsorption rate to neonicotinoid insecticides. It was applied as a superior magnetic adsorbent for rapid enrichment and isolation of four neonicotinoid insecticides (thiamethoxam, imidacloprid, acetamiprid and thiacloprid) from honey, tomato, lettuce and Chinese cabbage samples prior to high performance liquid chromatography-diode array detection. Under the optimized conditions, the good linearity was obtained in the range of 1-1000 ng g-1 for honey, tomato, lettuce and Chinese cabbage samples, and the detection limits (S/N = 3) were 0.30-0.67 ng g-1 for honey, 1-1.5 ng g-1 for tomato, lettuce and Chinese cabbage. The spiked recoveries were 80.1-111%, and relative standard deviations were less than 10.0%. These results demonstrate that the developed method can be used as a good alternative method for sensitive determination of neonicotinoid insecticides in complex samples.

Evaluation of 2-hydroxyethyl methacrylate as comonomer in the preparation of water-compatible molecularly imprinted polymers for triazinic herbicides

In this work, the preparation and evaluation of water-compatible molecularly imprinted polymers for triazines using 2-hydroxyethyl methacrylate and methacrylic acid as comonomers is described. Four sets of molecularly imprinted and non-imprinted polymers for propazine were prepared at varying monomer molar ratios (from 4:0 to 1:3), and evaluated for the recognition of several triazines directly in aqueous media. The evaluation was performed by loading 1 mL of an aqueous solution containing 500 ng of each selected triazine, washing with 500 μL of acetonitrile, and eluting with 500 μL of methanol followed by 2 × 500 μL of a solution of methanol containing 10% of acetic acid. Final determinations were performed by high-performance liquid chromatography-ultraviolet detection. Improvement in molecular recognition of triazines in water was obtained on those molecularly imprinted polymers incorporating 2-hydroxyethyl methacrylate in 3:1 or 2:2 molar ratios, being the former selected as optimum providing recoveries for propazine up to 80%. A molecularly imprinted solid-phase extraction protocol was developed to ensure that triazines-selective recognition takes place inside selective binding sites in pure water media. Finally, the developed method was successfully applied to the determination of the selected triazines in environmental waters providing limits of detection from 0.16 and the 0.5 μg/L concentration range.

Simple preparation of surface molecularly imprinted polymer based on silica particles for trace level assay of bisphenol F

A new electrochemical sensor based on molecularly imprinted tetraethyl orthosilicate (TEOS)-based porous interface was developed for selective recognition of bisphenol F (BPF) in this study. The sensor was prepared by depositing the solution containing TEOS and L-tryptophan (L-Trp) in the presence of cetyltrimethylammonium bromide (CTAB) as a pore-maker via hydrolysis/condensation reaction on the glassy carbon electrode (GCE). While the surface morphology and structure characterization were carried out using Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM), electrochemical characterization was performed through electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The resulted MIP(TEOS:L-Trp)@GCE achieved a wide linear range of 1 × 10^-15-1 × 10^-14 M for BPF detection with an excellent detection limit of 0.291 fM. Furthermore, the recovery of BPF from spiked bottled water and serum samples varied between 98.83 and 101.03%. These results demonstrate that MIP(TEOS:L-Trp)@GCE was found to be a simple, sensitive, and selective smart interface to detect trace pollution even from complicated samples.

Molecularly imprinted polymers via reversible addition-fragmentation chain-transfer synthesis in sensing and environmental applications

Molecularly imprinted polymers (MIP) have shown their potential as artificial and selective receptors for environmental monitoring. These materials can be tailor-made to achieve a specific binding event with a template through a chosen mechanism. They are capable of emulating the recognition capacity of biological receptors with superior stability and versatility of integration in sensing platforms. Commonly, these polymers are produced by traditional free radical bulk polymerization (FRP) which may not be the most suitable for enhancing the intended properties due to the poor imprinting performance. To improve the imprinting technique and the polymer capabilities, controlled/living radical polymerization (CRP) has been used to overcome the main drawbacks of FRP. Combining CRP techniques such as RAFT (reversible addition-fragmentation chain transfer) with MIP has achieved higher selectivity, sensitivity, and sorption capacity of these polymers when implemented as the transductor element in sensors. The present work focuses on RAFT-MIP design and synthesis strategies to enhance the binding affinities and their implementation in environmental contaminant sensing applications.

Synergistic recognition of transferrin by using performance dual epitope imprinted polymers

Transferrin (Trf) is a new type of active drug targeting carrier and disease biomarker that regulates the balance of iron ions in human body. The recognition and isolation of Trf is of great significance for disease diagnosis and treatment. Thus, a new type of magnetic dual affinity epitope molecularly imprinted polymer coated on Fe₃O₄ nanoparticles (Fe₃O₄@DEMIP) was successfully prepared for specific recognition of Trf. C-terminal nonapeptide and Trf glycan were selected as bi-epitope templates for metal chelation and boron affinity immobilization, respectively. 4-vinylphenylboric acid (4-VP), N-isopropyl acrylamide (NIPAM) and zinc acrylic were used as functional monomers. Results showed that Fe₃O₄@DEMIP exhibited excellent specific recognition ability adsorption capacity toward Trf, with an adsorption of 43.96 mg g^-1 (RSD = 3.28%) and a more satisfactory imprinting factor (about 6.60) than that of other reported imprinting methods. In addition, Fe₃O₄@DEMIP displayed pH, temperature and magnetic sensitivity properties to realize temperature and pH-controlled recognition and release of target proteins and magnetic rapid separation. Furthermore, the Fe₃O₄@DEMIP coupled with high-performance liquid chromatography (HPLC) analysis was successfully used for specific recognition of Trf in biosamples. This study provides a reliable protocol for preparing metal chelation and boron affinity dual affinity bi-epitope molecularly imprinted polymers for synergistic and efficient recognition of biomacromolecules in the complex biological systems.

Magnetic nanobiosorbent (MG-Chi/Fe3 O4 ) for dispersive solid-phase extraction of Cu(II), Pb(II), and Cd(II) followed by flame atomic absorption spectrometry determination

Trace amounts of Cu (II), Pb (II), and Cd (II) in a wastewater sample were preconcentrated with a novel cross‐linked magnetic chitosan modified with a new synthesised methionine‐glutaraldehyde Schiff's base (MG‐Chi/Fe₃O₄) as a dispersive solid‐phase extraction (DSPE) adsorbent. The adsorbed metal ions were then eluted with a specific volume of suitable solution and determined by flame atomic absorption spectrometry (FAAS). Various parameters affecting the extraction efficiency of the metal ions were investigated and optimised, including pH, amount of adsorbent, extraction time, type and volume rate of eluent, elution time, sample volume, and effect of interfering ions. The adsorption kinetics are more consistent with the pseudo‐second order model. The results were statistically interpreted and the analytical performance of the proposed method was found to have preconcentration factors of 55, 60, and 50 μg L⁻¹ for Cu(II), Pb(II), and Cd(II), respectively, limits of detection were 0.22, 0.24, and 0.10 μg L⁻¹ for Cu(II), Pb(II), and Cd(II), respectively, with a relative standard deviation (1.5%‐2.8 %), and the liner range was 5–1000 for Cu(II) and Pb(II) and 2.5–1000 for Cd(II). It was concluded that this method was suitable for successful simultaneous determination of Cu(II), Pb(II), and Cd(II) in industrial wastewater samples.

[Advances in application of molecularly imprinted polymers to the detection of polar pesticide residues]

Polar pesticides can be primarily classified as fungicides, herbicides, and insecticides; their rich variety and low cost have led to their extensive utilization in agriculture. However, the overuse of polar pesticides can lead to environmental contamination, such as water or soil pollution, which can also increase the risk of pesticide exposure among human life directly, or indirectly through contact with animal and plant-derived food. There are considerable differences in the physical and chemical properties of polar pesticides, as well as their trace amounts in complex food and environmental samples, posing immense challenges to their accurate detection. As a kind of artificially prepared selective adsorbent, molecularly imprinted polymers (MIPs) possess specific recognition sites complementary to template molecules in terms of the spatial structure, size, and chemical functional groups. With many advantages such as easy preparation, low cost, as well as good chemical and mechanical stability, MIPs have been widely applied in sample pretreatment and the analysis of polar pesticide residues. MIPs are typically used as adsorption materials in solid phase extraction (SPE) methods, including magnetic solid phase extraction (MSPE), dispersed solid phase extraction (DSPE), and stir bar sorptive extraction (SBSE). To rapidly detect polar pesticide residues with high sensitivity, MIPs are also used in the preparation of fluorescent sensors and electrochemical sensors. Furthermore, MIPs can be employed as the substrate in surface-enhanced Raman spectroscopy and as the substrate for the ion source in mass spectrometry for polar pesticide residue analysis. Thus far, various molecularly imprinted materials have been reported for the efficient separation and analysis of polar pesticide residues in various complex matrices. However, there is no review that summarizes the recent advances in MIPs for the determination of polar pesticides. This review introduces imprinting strategies and polymerization methods for MIPs, and briefly summarizes some new molecular imprinting strategies and preparation technologies. The application of MIPs in recent years (particularly the last five years) to the detection of polar pesticide residues including neonicotinoids, organophosphorus, triazines, azoles, and urea is then systematically summarized. Finally, the future development direction and trends for MIPs are proposed considering existing challenges, with the aim of providing reference to guide future research on MIPs in the field of polar pesticide residue detection.

Membrane Emulsification Process as a Method for Obtaining Molecularly Imprinted Polymers

The membrane emulsification process (ME) using a metallic membrane was the first stage for preparing a spherical and monodisperse thermoresponsive molecularly imprinted polymer (TSMIP). In the second step of the preparation, after the ME process, the emulsion of monomers was then polymerized. Additionally, the synthesized TSMIP was fabricated using as a functional monomer N-isopropylacrylamide, which is thermosensitive. This special type of polymer was obtained for the recognition and determination of trace bisphenol A (BPA) in aqueous media. Two types of molecularly imprinted polymers (MIPs) were synthesized using amounts of BPA of 5 wt.% (MIP-2) and 7 wt.% (MIP-1) in the reaction mixtures. Additionally, a non-imprinted polymer (NIP) was also synthesized. Polymer MIP-2 showed thermocontrolled recognition for imprinted molecules and a higher binding capacity than its corresponding non-imprinted polymer and higher than other molecularly imprinted polymer (MIP-1). The best condition for the sorption process was at a temperature of 35 °C, that is, at a temperature close to the phase transition value for poly(N-isopropylacrylamide). Under these conditions, the highest levels of BPA removal from water were achieved and the highest adsorption capacity of MIP-2 was about 0.5 mmol g-1 (about 114.1 mg g-1) and was approximately 20% higher than for MIP-1 and NIP. It was also observed that during the kinetic studies, under these temperature conditions, MIP-2 sorbed BPA faster and with greater efficiency than its non-imprinted analogue.

Molecularly Imprinted Polymers for Dispersive (Micro)Solid Phase Extraction: A Review

The review describes the development of batch solid phase extraction procedures based on dispersive (micro)solid phase extraction with molecularly imprinted polymers (MIPs) and magnetic MIPs (MMIPs). Advantages and disadvantages of the various MIPs for dispersive solid phase extraction and dispersive (micro)solid phase extraction are discussed. In addition, an effort has also been made to condense the information regarding MMIPs since there are a great variety of supports (magnetite and magnetite composites with carbon nanotubes, graphene oxide, or organic metal framework) and magnetite surface functionalization mechanisms for enhancing MIP synthesis, including reversible addition-fragmentation chain-transfer (RAFT) polymerization. Finally, drawbacks and future prospects for improving molecularly imprinted (micro)solid phase extraction (MIMSPE) are also appraised.

Molecular Imprinting: Green Perspectives and Strategies

Advances in revolutionary technologies pose new challenges for human life; in response to them, global responsibility is pushing modern technologies toward greener pathways. Molecular imprinting technology (MIT) is a multidisciplinary mimic technology simulating the specific binding principle of enzymes to substrates or antigens to antibodies; along with its rapid progress and wide applications, MIT faces the challenge of complying with green sustainable development requirements. With the identification of environmental risks associated with unsustainable MIT, a new aspect of MIT, termed green MIT, has emerged and developed. However, so far, no clear definition has been provided to appraise green MIT. Herein, the implementation process of green chemistry in MIT is demonstrated and a mnemonic device in the form of an acronym, GREENIFICATION, is proposed to present the green MIT principles. The entire greenificated imprinting process is surveyed, including element choice, polymerization implementation, energy input, imprinting strategies, waste treatment, and recovery, as well as the impacts of these processes on operator health and the environment. Moreover, assistance of upgraded instrumentation in deploying greener goals is considered. Finally, future perspectives are presented to provide a more complete picture of the greenificated MIT road map and to pave the way for further development.

Fast Determination of Carbamates in Environmental Water Based on Magnetic Molecularly Imprinted Polymers as Adsorbent

Magnetic molecularly imprinted polymers (MMIPs) were prepared with isoprocarb as template molecule and applied to extraction of carbamates pesticides in different water samples. This method based on magnetic solid-phase extraction (SPE) avoided the time-consuming column-passing process of loading large volume samples in conventional SPE. In the study, only 0.1 g MMIPs could be used to obtain satisfactory recoveries, due to the high-surface area and excellent adsorption capacity of these nano-magnetic adsorbents. Owing to the excellent selectivity of MMIPs, in high-performance liquid chromatography-mass spectrometry analysis, the matrix effects of this technique were obviously lower than the conventional SPE method. Under the optimal conditions, the detection limits of carbamates were in the range of 2.7-11.7 ng L-1. The relative standard deviations of intra-day and inter-day were 2.5-7.4% and 3.6-8.4%, respectively. At all the spiked level, the recoveries of four analyzed carbamates in environmental water samples were in the range of 74.2-94.2%. The significant positive results were achieved in the proposed method for the determination of four carbamates in water samples from different lakes and rivers. In the three samples we tested, the carbaryl was found in the lake water obtained from Yitong River, and the content was 2.4 ng L-1.

Magnetic molecularly imprinted polymer nanoparticles for the extraction and clean-up of thiamethoxam and thiacloprid in light and dark honey

In this work, new selective and sensitive dual-template molecularly imprinted polymer nanoparticles (MIPs) were synthesized and characterized. Sorbent MIPs were investigated for simultaneous extraction and clean-up of thiamethoxam and thiacloprid from light and dark honey samples. In this study, ultra-high-performance liquid chromatography-tandem mass spectrometry triple-quadrupole (UHPLC-MS/MS) (QQQ) was used to detect and quantify the pesticides. The kinetic model with adsorption kinetics of sorbent was investigated. The optimal adsorption conditions were 80 mg of polymer MIPs, a 30-min extraction time, and a pH of 7. The detection limit (LOD) and the quantification limit (LOQ) varied from 0.045 to 0.070 µg kg^-1 and from 0.07 to 0.10 µg kg^-1, respectively. The intra-day and inter-day precision (RSD, %) ranged from 1.3 to 2.0% and from 8.2 to 12.0%, respectively. The recovery of thiamethoxam and thiacloprid ranged from 96.8 to 106.5% and 95.3 to 104.4%, respectively, in light and dark honey samples.

Determination of phenols in natural and waste waters by capillary electrophoresis after preconcentration on magnetic nanoparticles coated with aminated hypercrosslinked polystyrene

An efficient sorbent for magnetic solid-phase extraction was developed from Fe₃ O₄ nanoparticles covered with aminated hypercrosslinked polystyrene. The sorbent has a saturation magnetization of 47 emu/g and a surface area of 509 mg/g and was tested for the extraction of 11 phenols from aqueous media. The optimum conditions were as follows: pH 3; adsorbent mass, 20.0 mg; adsorption time, 30 min; eluent (acetone) volume, 0.5 mL; and desorption time, 5 min. The enrichment factor after desorption reached 1595-1716 and the maximum adsorption capacity was 501-909 mg/g. Capillary electrophoresis was applied successively to separate 11 phenols after solid-phase extraction. The best separation was achieved using a fused silica capillary and borate buffer (pH 10.7) as a supporting electrolyte. After optimization, the linearity range was from 0.2 to 950 μg/L, and the limits of detection were 0.05-0.2 μg/L. The relative standard deviation varied from 6.1 to 8.7% (C = 1 μg/L) and from 2.9 to 3.5% (C = 500 μg/L). The determination of phenols is complicated in eutrophic water and spring water with a high content of humic and fulvic acids.

Innovative utilization of molecular imprinting technology for selective adsorption and (photo)catalytic eradication of organic pollutants

The rapid development of industrialization and urbanization results in a numerous production of various organic chemicals to meet the increasing demand in high-quality life. During the synthesis and utilization of these chemical products, their residues unavoidably emerged in environments to severely threaten human's health. It is thus urgent to exploit effective technology for readily removing the organic pollutants with high selectivity and good reusability. As one of the most promising approaches, molecular imprinting technology (MIT) employs a chemically synthetic route to construct artificial recognition sites in highly-crosslinked matrix with complementary cavity and functional groups to target species, which have been attracting more and more interest for environmental remediation, such as the selective adsorption/separation and improved catalytic degradation of pollutants. In this review, MIT is first introduced briefly to understand their preparing process, recognition mechanism and common imprinted systems. Then, their specific binding affinities are demonstrated for selectively adsorbing and removing target molecules with a large capacity. Furthermore, the innovative utilization of MIT in catalytic eradication of pollutants is comprehensively overviewed to emphasize their enhanced efficiency and improved performances, which are classified by the used catalytically-active nanocrystals and imprinted systems. After summarizing recent advances in these fields, some limitations are discussed and possible suggestions are given to guide the future exploitation on MIT for environmental protection.

Preparation of multi-walled carbon nanotubes based magnetic multi-template molecularly imprinted polymer for the adsorption of phthalate esters in water samples

Taking the advantages of surface imprinting, multi-template imprinting and magnetic separation, a novel magnetic multi-template molecularly imprinted polymer (mag-MMIP@MWCNTs) was prepared by using MWCNTs as support material, Fe₃O₄ as magnetic core, and dimethyl phthalate (DMP), diethyl phthalate (DEP), and dibutyl phthalate (DBP) as template molecules. This composite was characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR), vibrating sample magnetometer (VSM), and the Brunauer-Emmett-Teller (BET) analysis, and was used for the simultaneous adsorption of DMP, DEP, and DBP in aqueous solution. The effects of solution pH, contact time, PAEs initial concentration, temperature, adsorption selectivity, and reusability were investigated and discussed in detail. The results demonstrated that mag-MMIP@MWCNTs exhibited fast kinetics, good magnetic separation, and excellent selectivity for the adsorption of three phthalate esters (PAEs). The adsorption kinetics followed pseudo second-order kinetic model and the adsorption thermodynamics followed Langmuir isothermal model very well, and the maximum adsorption capacities (Q_max) of DMP, DEP, and DBP were obtained as 0.95, 1.38, and 7.09 mg g^-1, respectively. The Scatchard analysis revealed that the template-polymer system had a two-site binding behavior. The adsorption thermodynamic studies indicated that the adsorption processes were exothermic and spontaneous, and dominated by physical adsorption relying on hydrogen bond, hydrophobic interaction, and van der Waals force. Mag-MMIP@MWCNTs also showed good reproducibility and reusability for simultaneous adsorption of the three PAEs. The potential application of mag-MMIP@MWCNTs was proved by the removal of DMP, DEP, and DBP spiked in environmental water samples.

Latest Advances in Determination of Bisphenols with Nanomaterials, Molecularly Imprinted Polymers and Aptamer Based Electrochemical Sensors

Contamination of environmental sources such as soils, sediments and rivers and human exposure caused by several endocrine disrupting compounds (EDCs) are considered as the most challenging issues of today's world. EDCs cover a wide variety of compounds ranging from phthalates to parabens and bisphenols (BPs) are the leading group among them. BPs are widely used during the production of different plastic materials such as food and beverage containers, toys, medical equipment and baby bottles that we use in every aspect of our lives. BPs may migrate from those products to different media under certain conditions and this situation causes chronic exposure for humans and other creatures in the environment. Especially bisphenol A (BPA) and its other analogues such as bisphenol F, bisphenol S and tetrabromobisphenol that have similar structures and are preferred as alternatives to BPA cause harmful adverse effects such as endocrine disruption, neurotoxicity, genotoxicity and cytotoxicity. There are legal restrictions and prohibitions by the European Union (EU) in order to prevent possible harmful effects. Therefore, it is important to develop highly sensitive, fast, easy to use and cheap sensors for the determination of BPs in biological, environmental and commercial samples. Electrochemical sensors, which are one of the most widely, used analytical techniques, provide these conditions. Additionally, it is possible to enhance the performance of electrochemical sensors with nanomaterials, molecularly imprinted polymers or aptamer based technologies. This review aims to give comprehensive information about BPs with summarizing most recent applications of electrochemical sensors for their determination in different samples.

Magnetic solid phase extraction followed by in-situ derivatization with core-shell structured titanium dioxide coated ferriferrous oxide microspheres for determination of alendronate in plasma

In this study, for the first time, magnetic solid phase extraction (MSPE) was combined with in-situ derivatization to determine alendronate in plasma. TiO₂ coated Fe₃O₄ microspheres (denoted as Fe₃O₄@TiO₂) were synthesized via polydopamine coating, titanium ions immobilizing and calcination steps. The as-prepared microspheres could selectively extract alendronate and be quickly isolated from plasma. The drug-adsorbed Fe₃O₄@TiO₂ microspheres were then directly incubated in derivatization reagent solution to perform novel in-situ derivatization and elution procedure, in which the derivatized alendronate lost its affinity to TiO₂ and was spontaneously eluted for further LC-MS/MS detection. Satisfactory results were obtained on the creative attempt to couple dispersive magnetic solid phase extraction with in-situ derivatization. The developed method was validated and demonstrated good linearity (0.05-500 ng mL^-1), low detection limit (20 pg mL^-1), great accuracy (100.6% to 105.3%) and precision (RSDs<5.27%). Manual operation and analysis time could be greatly reduced compared to other reported methods. The method was successfully applied to a pharmacokinetic study in beagle dogs.

Multi-Walled Carbon Nanotubes for Magnetic Solid-Phase Extraction of Six Heterocyclic Pesticides in Environmental Water Samples Followed by HPLC-DAD Determination

Magnetic multi-walled carbon nanotubes were prepared as magnetic solid-phase extraction (MSPE) adsorbent for the enrichment of six heterocyclic pesticides in environmental water samples, including imidacloprid, triadimefon, fipronil, flusilazole, chlorfenapyr and fenpyroximate. Then six heterocyclic pesticides were separated and determined by high-performance liquid chromatography-diode-array detector (HPLC-DAD). Major factors influencing MSPE efficiency, including the dose of mag-multi-walled carbon nanotubes (mag-MWCNTs), extraction time, solution pH, salt concentration, type and volume of eluent and desorption time were investigated. Under the optimized conditions, the enrichment factor of the method reached to 250. The linearity was achieved within 0.05–10.0 μg/L for imidacloprid and chlorfenapyr, 0.10–10.0 μg/L for fipronil, flusilazole, triadimefon and fenpyroximate. Limits of detection were in the range of 0.01–0.03 μg/L. Good precision at three spiked levels were 1.1–11.2% (intra-day) and 1.7–11.0% (inter-day) with relative standard deviation of peak area, respectively. The developed method was utilized to analyze tap water, river water and reservoir water samples and recoveries at three spiked concentration levels ranged from 72.2% to 107.5%. The method was proved to be a convenient, rapid and practical method for sensitive determination of heterocyclic pesticides.

Application of stimuli-responsive materials for extraction purposes

Stimuli-responsive materials, frequently designated as "smart/intelligent materials", can modify their structure or properties by either a biological, physical, or chemical stimulus which, if properly controlled, could be used for specific applications. Such materials have been studied and exploited in several fields, like electronics, photonics, controlled drugs administration, imaging and medical diagnosis, among others, as well as in Analytical Chemistry where they have been used as chromatographic stationary phases, as part of sensors and for extraction purposes. This review article pretends to provide an overview of the most recent applications of these materials (mostly polymeric materials) in sample preparation for extraction purposes, as well as to provide a general vision of the current state-of-the-art of this field, their potential use and future applications.

Advances in Electrochemical Impedance Spectroscopy Detection of Endocrine Disruptors

Endocrine disruptors (EDs) are contaminants that may mimic or interfere with the body's hormones, hampering the normal functions of the endocrine system in humans and animals. These substances, either natural or man-made, are involved in development, breeding, and immunity, causing a wide range of diseases and disorders. The traditional detection methods such as enzyme linked immunosorbent assay (ELISA) and chromatography are still the golden techniques for EDs detection due to their high sensitivity, robustness, and accuracy. Nevertheless, they have the disadvantage of being expensive and time-consuming, requiring bulky equipment or skilled personnel. On the other hand, early stage detection of EDs on-the-field requires portable devices fulfilling the Affordable, Sensitive, Specific, User-friendly, Rapid and Robust, Equipment free, Deliverable to end users (ASSURED) norms. Electrochemical impedance spectroscopy (EIS)-based sensors can be easily implemented in fully automated, sample-to-answer devices by integrating electrodes in microfluidic chips. The latest achievements on EIS-based sensors are discussed and critically assessed.

Fast and simple determination of estrogens in milk powders by magnetic solid-phase extraction using carbon nitride composites prior to HPLC

A graphitic carbon nitride (g-C₃N₄/Fe₃O₄)-based magnetic solid-phase extraction (MSPE) approach was established for fast and simple analysis of estrogens in milk powders. The composites were characterized by X-ray diffractometer, scanning electron microscope, and Brunauer-Emmett-Teller surface area and pore size distribution analyzer. Compared with the bulk g-C₃N₄, g-C₃N₄/Fe₃O₄ gave a narrower distribution of mesopores and provided an enhanced surface area from 77.1 to 113.7 m²/g. Polar analytes of estrogens were selected as model compounds and the extraction of four estrogens was achieved in n-hexane using 15 mg of adsorbent within only 2 min. Possible extraction mechanism of g-C₃N₄/Fe₃O₄ for these estrogens was explored in terms of the polarity of the analytes and the adsorption performance of the adsorbent. The hydrophobicity and the hydrogen-bond interaction between the estrogens and g-C₃N₄ were responsible for the efficient adsorption. Combined with HPLC, MSPE with the prepared adsorbent gave the enhancement factors of 20 to 24 and the linear ranges of 2-200 μg/kg for 17β-estradiol and 17α-ethinylestradiol, 1.5-150 μg/kg for estrone, and 3-300 μg/kg for hexestrol. The detection limits and quantification limits for the estrogens in milk powders were 0.5-0.9 μg/kg and 1.5-3.0 μg/kg, respectively. The recoveries varied from 75.1 to 97.2%, with the intra-day and inter-day precisions ≤ 14.2%. Furthermore, the enrichment of the analytes and the clean-up of fat and protein interferences were achieved simultaneously with one-step g-C₃N₄-based MSPE. The present method was convenient, fast, and sensitive, and therefore could be successfully applied for the determination of estrogens in milk powders. Graphical abstract.

Smart materials for point-of-care testing: From sample extraction to analyte sensing and readout signal generator

The last decade has seen a surge of technical developments in the field on point-of-care testing (POCT). While these developments are extremely diverse, the common aim is to implement improved methods for quick, reliable and inexpensive diagnosis of patients within the clinical setting. While examples of successful introduction and use of POCT techniques are growing, further developments are still necessary to create POCT devices with better portability, usability and performance. Advances in smart materials emerge as potentially valuable know-hows to provide a competitive edge to the development of next generation POCT devices. This review describes the key advantages of adopting smart material-based technologies at different analytical stages of a POCT platform. Under these analytical stages which involves sample pre-treatment, analyte sensing and readout signal generator, several concepts and approaches from contemporary research work in using smart material-based technologies will be the major focus in this review. Lastly, challenges and potential outlook in implementing materials technologies from the application point of view for POCT will be discussed.

A rational route to hybrid aptamer-molecularly imprinted magnetic nanoprobe for recognition of protein biomarkers in human serum

Although antibody has played a great role in highly specific recognition of protein biomarkers, it faces poor stability, reproducibility, high-cost and time-consuming preparation, etc. Here, aptamer and molecularly imprinted polymers (MIPs), both as promising substitutes of antibody, were integrated onto magnetic nanoparticles by Au-S bonds and SiO₂ as imprinted layer for preparing a new nanoprobe. Highly specific and sensitive recognition of different protein biomarkers, such as insulin for diabetes and alpha-fetoprotein (AFP) for hepatic carcinoma, were achieved respectively by the system of combining hybrid aptamer-molecularly imprinted magnetic nanoprobe and mass spectrometry. With the double affinities offered by aptamer-MIPs, insulin can be detected at 0.5 ng mL^-1 in human serum dilution, the equlibrium dissociation constant between nanoprobe and insulin is measured as 23.61 ± 2.27 μM. Likewise, AFP can be sufficiently detected in human saliva dilution from 1000 ng mL^-1 to 20 ng mL^-1, and two patients with hepatic carcinoma are discriminated from healthy person due to the abnormally high expression of AFP in serum.