Environmental applications for biosurfactants

High efficiency of biosurfactants in stabilizing oil micro-droplets within the aging time scale of milliseconds: a microfluidic study

Rapid adsorption of surfactants onto a freshly formed interface is vital for emulsification because emulsification is a competitive process occurring between the very short time span of interface formation and surfactant mass transport. The biosurfactant surfactin has been previously reported to reach adsorption equilibrium at the hydrophobic/hydrophilic interface within hundreds of milliseconds and rapidly reduce the interfacial tension compared to chemically synthesized surfactants. According to a prior study, surfactin is expected to exhibit good performance in stabilizing micro-droplets of oil within the aging time scale of milliseconds. Herein, the stabilities of micro-droplets of n-hexadecane in the presence of a biosurfactant, surfactin (C15-SFT), and a chemically synthesized surfactant, sodium cetyl benzene sulfonate (8-SCBS), were investigated using a microfluidic method. The coalescence frequency of micro-droplets, the evolution of micro-droplet size, and the coalescence time of micro-droplets were evaluated. The results indicated that C15-SFT exhibited superiority over 8-SCBS in stabilizing the micro-droplets of n-hexadecane. Biosurfactant C15-SFT effectively reduced the fusion probability between oil droplets and elongated the coalescence time compared to 8-SCBS, and these phenomena were obvious at a shorter aging time (150 ms) and lower surfactant concentration (0.1 × critical micelle concentration). The stabilities of micro-droplets increased with aging time and the bulk concentration of surfactants. Stable micro-droplets of n-hexadecane were formed in 1 × 10-4 mol L-1 C15-SFT solution at 600 ms aging time, and the bulk concentration was 1 × 10-3 mol L-1 in the case of 8-SCBS. The micro-droplets rarely coalesced in the presence of 1 × 10-4 mol L-1 C15-SFT after 600 ms aging time, but the micro-droplets in 1 × 10-4 mol L-1 8-SCBS coalesced frequently in the midstream and downstream of the coalescence chamber, and big droplets were dominant in the emulsion. The coalescence time of micro-droplets stabilized by C15-SFT was obviously longer than that of those stabilized by 8-SCBS under the same condition, indicating that the interfacial film formed by C15-SFT has much strength to resist coalescence during collisions. This work is helpful for understanding the activity of lipopeptides in the very short early stage of the emulsification process, laying the foundation for biosurfactant research in the fields of enhanced oil recovery, bioremediation of contaminated water or soil, etc.

Bioemulsifier from sponge-associated bacteria reduces staphylococcal biofilm

Biofilm formation is a major health concern and studies have been pursued to find compounds able to prevent biofilm establishment and remove pre-existing biofilms. While biosurfactants (BS) have been well-known for possessing antibiofilm activities, bioemulsifiers (BE) are still scarcely explored for this purpose. The present study aimed to evaluate the bioemulsifying properties of cell-free supernatants produced by Bacillaceae and Vibrio strains isolated from marine sponges and investigate their antiadhesive and antibiofilm activities against different pathogenic Gram-positive and Gram-negative bacteria. The BE production by the marine strains was confirmed by the emulsion test, drop-collapsing, oil-displacement, cell hydrophobicity and hemolysis assays. Notably, Bacillus cereus 64BHI1101 displayed remarkable emulsifying activity and the ultrastructure analysis of its BE extract (BE64-1) revealed the presence of structures typically observed in macromolecules composed of polysaccharides and proteins. BE64-1 showed notable antiadhesive and antibiofilm activities against Staphylococcus aureus, with a reduction of adherence of up to 100 % and a dispersion of biofilm of 80 %, without affecting its growth. BE64-1 also showed inhibition of Staphylococcus epidermidis and Escherichia coli biofilm formation and adhesion. Thus, this study provides a starting point for exploring the antiadhesive and antibiofilm activities of BE from sponge-associated bacteria, which could serve as a valuable tool for future research to combat S. aureus biofilms.

Biodegradation of a complex hydrocarbon mixture and biosurfactant production by Burkholderia thailandensis E264 and an adapted microbial consortium

Bioremediation is considered to be an effective treatment for hydrocarbon removal from polluted soils. However, the effectiveness of this treatment is often limited by the low availability of targeted contaminants. Biosurfactants produced by some microorganisms can increase organic compound solubility and might then overcome this limitation. Two different inocula producers of biosurfactants (Burkholderia thailandensis E264 and SHEMS1 microbial consortium isolated from a hydrocarbon-contaminated soil) were incubated in Bushnell-Haas medium supplemented with hydrocarbons to investigate their biodegradation potential. Experimental results showed their ability to degrade 9.1 and 6.1% of hydrocarbons respectively after 65 days of incubation with an initial total hydrocarbon concentration of 16 g L-1. The biodegradation was more effective for the light and medium fractions (C10 to C36). B. thailandensis and SHEMS1 consortium produced surfactants after 14 days of culture during the stationary phase with hydrocarbons as the sole carbon and energy source. However, biosurfactant production did not appear to directly increase hydrocarbon degradation efficiency. The complexity and recalcitrance of hydrocarbon mixture used in this study appeared to continue to limit its biodegradation even in the presence of biosurfactants. In conclusion, B. thailandensis and SHEMS1 consortium can degrade recalcitrant hydrocarbon compounds and are therefore good candidates for the bioremediation of environments polluted by total hydrocarbons.

Glycolipids biosurfactants production using low-cost substrates for environmental remediation: progress, challenges, and future prospects

The production of renewable materials from alternative sources is becoming increasingly important to reduce the detrimental environmental effects of their non-renewable counterparts and natural resources, while making them more economical and sustainable. Chemical surfactants, which are highly toxic and non-biodegradable, are used in a wide range of industrial and environmental applications harming humans, animals, plants, and other entities. Chemical surfactants can be substituted with biosurfactants (BS), which are produced by microorganisms like bacteria, fungi, and yeast. They have excellent emulsifying, foaming, and dispersing properties, as well as excellent biodegradability, lower toxicity, and the ability to remain stable under severe conditions, making them useful for a variety of industrial and environmental applications. Despite these advantages, BS derived from conventional resources and precursors (such as edible oils and carbohydrates) are expensive, limiting large-scale production of BS. In addition, the use of unconventional substrates such as agro-industrial wastes lowers the BS productivity and drives up production costs. However, overcoming the barriers to commercial-scale production is critical to the widespread adoption of these products. Overcoming these challenges would not only promote the use of environmentally friendly surfactants but also contribute to sustainable waste management and reduce dependence on non-renewable resources. This study explores the efficient use of wastes and other low-cost substrates to produce glycolipids BS, identifies efficient substrates for commercial production, and recommends strategies to improve productivity and use BS in environmental remediation.

Sand washing of oil spill-affected beaches using concentrated β-glucans obtained from residual baker's yeast

Valorization of residual yeast of the bakery industry for use in the remediation of oil-contaminated soils as an emulsifier is a biocompatible and effective process that will reduce environmental pollution. The aim of this study was to use concentrated β-glucan obtained from residual baker's yeast, Saccharomyces cerevisiae, as an emulsifier to remove total petroleum hydrocarbons (TPH) from the contaminated sands of two beaches affected by the oil spill that occurred in January 2022 north of Lima, Peru. The extraction and concentration of β-glucan from sand were performed at a pilot scale using autolysis with 3 % sodium chloride, temperature elevation, treatment with organic solvents and water, hydrolysis via proteases, and vacuum filtration. The chemical composition and functional properties of concentrated β-glucan were evaluated to determine its quality and efficacy. In addition, the values of TPH removal efficiency obtained using concentrated β-glucan, water, and the commercial emulsifier Tween-80 were compared. The mass recovery of concentrated β-glucan was 5.59 %, with a β-glucan content of 38.60 %. The efficiency of ex-situ removal of TPH from hydrocarbon-impacted sands containing 78323 mg/kg of TPH reached 50 % and 70 % when the concentrated β-glucan concentrations used were 70.3 % and 80.3 %, respectively. These efficiency values are higher than those obtained when water was used for TPH removal but lower than those obtained when Tween-80 was used for TPH removal.

Incorporation of Multiple β2-Hydroxy Acids into a Protein In Vivo Using an Orthogonal Aminoacyl-tRNA Synthetase

The programmed synthesis of sequence-defined biomaterials whose monomer backbones diverge from those of canonical α-amino acids represents the next frontier in protein and biomaterial evolution. Such next-generation molecules provide otherwise nonexistent opportunities to develop improved biologic therapies, bioremediation tools, and biodegradable plastic-like materials. One monomer family of particular interest for biomaterials includes β-hydroxy acids. Many natural products contain isolated β-hydroxy acid monomers, and polymers of β-hydroxy acids (β-esters) are found in polyhydroxyalkanoate (PHA) polyesters under development as bioplastics and drug encapsulation/delivery systems. Here we report that β2-hydroxy acids possessing both (R) and (S) absolute configuration are substrates for pyrrolysyl-tRNA synthetase (PylRS) enzymes in vitro and that (S)-β2-hydroxy acids are substrates in cellulo. Using the orthogonal MaPylRS/MatRNAPyl synthetase/tRNA pair, in conjunction with wild-type E. coli ribosomes and EF-Tu, we report the cellular synthesis of model proteins containing two (S)-β2-hydroxy acid residues at internal positions. Metadynamics simulations provide a rationale for the observed preference for the (S)-β2-hydroxy acid and provide mechanistic insights that inform future engineering efforts. As far as we know, this finding represents the first example of an orthogonal synthetase that acylates tRNA with a β2-hydroxy acid substrate and the first example of a protein hetero-oligomer containing multiple expanded-backbone monomers produced in cellulo.

Biosurfactants production by marine yeasts isolated from zoanthids and characterization of an emulsifier produced by Yarrowia lipolytica LMS 24B

The present study investigates the potential for biosurfactant production of 19 marine yeast species obtained from zoanthids. Using the emulsification index test to screen the samples produced by the marine yeasts, we verified that five isolates exhibited an emulsification index ≥50%. Additional tests were performed on such isolates, including oil displacement, drop collapse, Parafilm M assay, and surface tension measurement. The tolerance of produced biosurfactants for environmental conditions was also analyzed, especially considering the media's temperature, pH, and salinity. Moreover, the surfactant's ability to emulsify different hydrocarbon sources and to metabolize kerosene as the sole carbon source was evaluated in vitro. Our results demonstrate that yeast biosurfactants can emulsify hydrocarbon sources under different physicochemical conditions and metabolize kerosene as a carbon source. Considering the Yarrowia lipolytica LMS 24B as the yeast model for biosurfactant production from the cell's wall biomass, emulsification indexes of 61.2% were obtained, even at a high temperature of 120 °C. Furthermore, the Fourier-transform middle infrared spectroscopy (FTIR) analysis of the biosurfactant's chemical composition revealed the presence of distinct functional groups assigned to a glycoprotein complex. Considering the status of developing new bioproducts and bioprocesses nowadays, our findings bring a new perspective to biosurfactant production by marine yeasts, especially Y. lipolytica LMS 24B. In particular, the presented results validate the relevance of marine environments as valuable sources of genetic resources, i.e., yeast strains capable of metabolizing and emulsifying petroleum derivatives.

Advances in the production of biosurfactants as green ingredients in home and personal care products

Home and personal care industry is currently witnessing a growing demand for sustainable and eco-friendly alternatives to synthetic surfactants. This increase is fueled by concerns over the delayed degradation and environmental impact of the latter. To this, biosurfactants possess important properties such as biodegradability, low toxicity, and renewable sourcing. These qualities position them as compelling replacements of traditional synthetic surfactants. Their diverse attributes including emulsification, antimicrobial efficacy, surface tension reduction, and foaming capability, make them well-suited choices for home and personal care products. Biosurfactants can be produced through several inexpensive and renewable sources which contributes to their commercialization potential. This article discusses various microbial derived biosurfactants including rhamnolipids, sophorolipids, mannosyl-erythritol lipids, trehalolipids and lipopeptides, unraveling and comparing their distinctive roles and advantages in the home and personal care industry. It also focuses on the recent patent innovations in the production of biosurfactants which have aimed at improving their economic viability and performance attributes. Finally, the article sheds light on the challenges and future trajectories for better integration of these sustainable biosurfactants into mainstream consumer products.

Microbial lipopeptides: their pharmaceutical and biotechnological potential, applications, and way forward

As lead molecules, cyclic lipopeptides with antibacterial, antifungal, and antiviral properties have garnered a lot of attention in recent years. Because of their potential, cyclic lipopeptides have earned recognition as a significant class of antimicrobial compounds with applications in pharmacology and biotechnology. These lipopeptides, often with biosurfactant properties, are amphiphilic, consisting of a hydrophilic moiety, like a carboxyl group, peptide backbone, or carbohydrates, and a hydrophobic moiety, mostly a fatty acid. Besides, several lipopeptides also have cationic groups that play an important role in biological activities. Antimicrobial lipopeptides can be considered as possible substitutes for antibiotics that are conventional to address the current drug-resistant issues as pharmaceutical industries modify the parent antibiotic molecules to render them more effective against antibiotic-resistant bacteria and fungi, leading to the development of more resistant microbial strains. Bacillus species produce lipopeptides, which are secondary metabolites that are amphiphilic and are typically synthesized by non-ribosomal peptide synthetases (NRPSs). They have been identified as potential biocontrol agents as they exhibit a broad spectrum of antimicrobial activity. A further benefit of lipopeptides is that they can be produced and purified biotechnologically or biochemically in a sustainable manner using readily available, affordable, renewable sources without harming the environment. In this review, we discuss the biochemical and functional characterization of antifungal lipopeptides, as well as their various modes of action, method of production and purification (in brief), and potential applications as novel antibiotic agents.

Exploring fungal bioemulsifiers: insights into chemical composition, microbial sources, and cross-field applications

The demand for emulsion-based products is crucial for economic development and societal well-being, spanning diverse industries such as food, cosmetics, pharmaceuticals, and oil extraction. Formulating these products relies on emulsifiers, a distinct class of surfactants. However, many conventional emulsifiers are derived from petrochemicals or synthetic sources, posing potential environmental and human health risks. In this context, fungal bioemulsifiers emerge as a compelling and sustainable alternative, demonstrating superior performance, enhanced biodegradability, and safety for human consumption. From this perspective, the present work provides the first comprehensive review of fungal bioemulsifiers, categorizing them based on their chemical nature and microbial origin. This includes polysaccharides, proteins, glycoproteins, polymeric glycolipids, and carbohydrate-lipid-protein complexes. Examples of particular interest are scleroglucan, a polysaccharide produced by Sclerotium rolfsii, and mannoproteins present in the cell walls of various yeasts, including Saccharomyces cerevisiae. Furthermore, this study examines the feasibility of incorporating fungal bioemulsifiers in the food and oil industries and their potential role in bioremediation events for oil-polluted marine environments. Finally, this exploration encourages further research on fungal bioemulsifier bioprospecting, with far-reaching implications for advancing sustainable and eco-friendly practices across various industrial sectors.

Enhanced washing of polycyclic aromatic hydrocarbons from contaminated soils by the empowered surfactant properties of de novo O-alkylated humic matter

Aqueous solutions of humic acid (HA) derivatized by a catalyzed O-alkylation reaction with methyl, pentyl, and benzyl groups at 40, 60, and 80% of total HA acidity were used to wash off polycyclic aromatic hydrocarbons (PAHs) from two contaminated soils. The enhanced surfactant properties enabled the alkylated HA to remove phenanthrene, anthracene, fluoranthene, and pyrene from both soils more extensively than the original unmodified HA, the 60% benzylation generally showing the greatest soil washing efficiency. For both soils, all alkylated HA revealed greater PAH removals than Triton X-100 nonionic surfactant, while the benzylated and methylated HA nearly and fully matched pollutants release by the anionic SDS in the coarse- and fine-textured soils, respectively. A consecutive second washing with 60% benzylated HA removed additional PAHs, in respect to the first washing, from the coarser-textured soil, except for fluoranthene, while removal from the finer-textured soil incremented even more for all PAHs. These findings indicate that the enhanced hydrophobicity obtained by a simple and unexpensive chemical derivatization of a natural humic surfactant can be usefully exploited in the washing of polluted soils, without being toxic to the soil biota and by potentially promoting the subsequent bio-attenuation of organic pollutants.

Unlocking the potential of biosurfactants: Production, applications, market challenges, and opportunities for agro-industrial waste valorization

Biosurfactants are eco-friendly compounds with unique properties and promising potential as sustainable alternatives to chemical surfactants. The current review explores the multifaceted nature of biosurfactant production and applications, highlighting key fermentative parameters and microorganisms able to convert carbon-containing sources into biosurfactants. A spotlight is given on biosurfactants' obstacles in the global market, focusing on production costs and the challenges of large-scale synthesis. Innovative approaches to valorizing agro-industrial waste were discussed, documenting the utilization of lignocellulosic waste, food waste, oily waste, and agro-industrial wastewater in the segment. This strategy strongly contributes to large-scale, cost-effective, and environmentally friendly biosurfactant production, while the recent advances in waste valorization pave the way for a sustainable society.

Critical evaluation of the performance of rhamnolipids as surfactants for (phyto)extraction of Cd, Cu, Fe, Pb and Zn from copper smelter-affected soil

Rhamnolipids are biosurfactants produced by bacteria belonging to the Pseudomonas genus. They are discussed to complex heavy metal cations stronger than cations of Fe, Ca, Mg. It is therefore suggested to employ rhamnolipids in phytoextraction where their addition to soil should result in preferential complexation of heavy metals that can be taken up by plants, thus enabling rapid and ecological clean-up of contaminated soil. In order to test this concept, we evaluated the rhamnolipid-mediated phytoextraction of heavy metal from soil collected from the vicinity of a copper smelter. The following aspects were investigated: i) selectivity of rhamnolipids towards Cu, Zn, Pb, Cd and Fe during soil washing; ii) phytoextraction efficiency of each ion with respect to the effective concentration of rhamnolipids; iii) possible phytotoxic effects; iv) effect of micro-sized polystyrene amendment. The experiments evaluated soil washing efficiency, BCR (Community Bureau of Reference) sequential extraction to determine the impact of rhamnolipids on the mobility of metal ions, phytoextraction with maize (Zea mays L.) and phytotoxic effects based on dry matter, chlorophyll fluorescence and content. The obtained results indicated that rhamnolipids lack desired selectivity towards heavy metal ions as Fe was complexed more efficiently by 80 % of the available rhamnolipids compared to priority pollutants like Zn, Cu, Pb, which were complexed by only 20 % of the tested rhamnolipids. With increased concentration of rhamnolipids, the soil washing efficiency increased and shifted in favour of Fe, reaching values of approx. 469 mg for Fe and only 118 mg in total of all tested heavy metals. Phytoextraction also favoured the accumulation of Fe, while Cd was not removed from the soil even at the highest applied rhamnolipid concentrations. Considering the selectivity of rhamnolipids and the costs associated with their production, our results suggest the need to search for other alternative (bio)surfactants with better selectivity and lower price.

Advances in ultrasonic treatment of oily sludge: mechanisms, industrial applications, and integration with combined treatment technologies

In the petroleum sector, the generation of oily sludge is an unavoidable byproduct, necessitating the development of efficient treatment strategies for both economic gain and the mitigation of negative environmental impacts. The intricate composition of oily sludge poses a formidable challenge, as existing treatment methodologies frequently fall short of achieving baseline disposal criteria. The processes of demulsification and dehydration are integral to diminishing the oil content and reclaiming valuable crude oil, thereby playing a critical role in the management of oily sludge. Among the myriad of treatment solutions, ultrasonic technology has emerged as a particularly effective physical method, celebrated for its diverse applications and lack of resultant secondary pollution. This comprehensive review delves into the underlying mechanisms and recent progress in the ultrasonic treatment of oily sludge, with a specific focus on its industrial implementations within China. Both isolated ultrasonic treatment and its combination with other technological approaches have proven successful in addressing oily sludge challenges. The adoption of industrial-scale systems that amalgamate ultrasound with multi-technological processes has shown marked enhancements in treatment efficacy. The fusion of ultrasonic technology with other cutting-edge methods holds considerable potential across a spectrum of applications. To fulfill the goals of resource recovery, reduction, and neutralization in oily sludge management, the industrial adoption and adept application of a variety of treatment technologies are imperative.

Structural and compositional diversity of biosurfactants produced by a novel strain of Sporosarcina luteola ME44 from oil reservoir

The urealytically active microorganism Sporosarcina luteola induces the precipitation of metals, which has attracted attention in biomineralization, bioremediation, and industrial waste recycling. Herein, we report a novel biosurfactant-producing strain of S. luteola ME44 isolated from Chinese Oilfield. The structure, composition, and surface activity of the biosurfactants produced by S. luteola ME44 were investigated by using a combination of the high-performance liquid chromatography, time-of-flight mass spectrometry, and surface tensiometer. The biosurfactant extracted by strain ME44 was identified as surfactin with five variants and the yield was 1010 ± 60 mg⋅L-1 . This is the first report on the structural composition and surface activity of biosurfactants isolated from the S. luteola. It extended our knowledge about the role of the species S. luteola in the ecosystem of extreme natural environments such as oil reservoir. In addition, S. luteola ME44 showed bioprecipitation properties for metal ions Cd(II), Cu(II), Zn(II), and Ag(I), which indicated the application potential of S. luteola in the field of bioremediation.

Main Factors Determining the Scale-Up Effectiveness of Mycoremediation for the Decontamination of Aliphatic Hydrocarbons in Soil

Soil contamination constitutes a significant threat to the health of soil ecosystems in terms of complexity, toxicity, and recalcitrance. Among all contaminants, aliphatic petroleum hydrocarbons (APH) are of particular concern due to their abundance and persistence in the environment and the need of remediation technologies to ensure their removal in an environmentally, socially, and economically sustainable way. Soil remediation technologies presently available on the market to tackle soil contamination by petroleum hydrocarbons (PH) include landfilling, physical treatments (e.g., thermal desorption), chemical treatments (e.g., oxidation), and conventional bioremediation. The first two solutions are costly and energy-intensive approaches. Conversely, bioremediation of on-site excavated soil arranged in biopiles is a more sustainable procedure. Biopiles are engineered heaps able to stimulate microbial activity and enhance biodegradation, thus ensuring the removal of organic pollutants. This soil remediation technology is currently the most environmentally friendly solution available on the market, as it is less energy-intensive and has no detrimental impact on biological soil functions. However, its major limitation is its low removal efficiency, especially for long-chain hydrocarbons (LCH), compared to thermal desorption. Nevertheless, the use of fungi for remediation of environmental contaminants retains the benefits of bioremediation treatments, including low economic, social, and environmental costs, while attaining removal efficiencies similar to thermal desorption. Mycoremediation is a widely studied technology at lab scale, but there are few experiences at pilot scale. Several factors may reduce the overall efficiency of on-site mycoremediation biopiles (mycopiles), and the efficiency detected in the bench scale. These factors include the bioavailability of hydrocarbons, the selection of fungal species and bulking agents and their application rate, the interaction between the inoculated fungi and the indigenous microbiota, soil properties and nutrients, and other environmental factors (e.g., humidity, oxygen, and temperature). The identification of these factors at an early stage of biotreatability experiments would allow the application of this on-site technology to be refined and fine-tuned. This review brings together all mycoremediation work applied to aliphatic petroleum hydrocarbons (APH) and identifies the key factors in making mycoremediation effective. It also includes technological advances that reduce the effect of these factors, such as the structure of mycopiles, the application of surfactants, and the control of environmental factors.

Surfactant-Mediated Effects on Hydrological and Physical Soil Properties: Data Synthesis

Soils are under the threat of a multitude of anthropogenic factors affecting the complex interplay of various physical and hydrological soil processes and properties. One such factor is the group of surface-active compounds. Surfactants have a broad range of applications and can reduce solid-liquid interfacial forces and increase wettability and dispersion of particles. Surfactant effects are context-dependent, giving rise to a wide range of reported effects on different soil processes and properties. Here, we evaluate the evidence base of surfactant research on 11 hydrological and physical soil variables. Our goal was to identify knowledge gaps and test the robustness of the proposed surfactant effects. We found that the current knowledge base is insufficient to reach strong data-backed conclusions about the effects of surfactants in soils. We identified a unique case of bias in the data as a result of conflated patterns from laboratory and field studies. We could not support the hypothesis that the surfactant charge determines soil effects for any of the tested soil variables. We believe that further experiments on surfactant-mediated effects on soil properties and processes are urgently required, paying attention, in particular, to improving experimental design and data reporting standards.

Alteration in Community Dynamics of Chaetoceros curvisetus and Bacterioplankton Communities in Response to Surfactin Exposure

The use of surfactin is a promising method to mitigate algal blooms. However, little is known about surfactin toxicity to algae and bacterioplankton. Here, we treated Chaetoceros curvisetus, the dominant species of algal blooms in the East China Sea, with 0, 0.5, 1, 2, 3, and 4 mg/L of surfactin for 96 h to investigate temporal variability. Our results showed that low concentrations of surfactin (<2 mg/L) changed the cell morphology of C. curvisetus, and higher concentrations (>3 mg/L) had lethal effects. Meanwhile, we examined the community dynamics of the free-living (FL, 0.22-5 μm) and particle-attached (PA, >5 μm) bacterioplankton of C. curvisetus in response to different surfactin concentrations and cultivation periods. Both PA and FL bacterioplankton were mainly composed of Proteobacteria, Actinobacteria, and Bacteroidetes, while FL bacterioplankton were more diverse than PA bacterioplankton. The variations of FL and PA bacterioplankton were significantly constrained by the surfactin concentration. Surfactin changed the lifestyle of some bacterioplankton from FL to PA, which mainly belonged to abundant bacterioplankton. Furthermore, we identified some surfactin-sensitive species/taxa. Our study will help enhance the ability to predict marine microbial responses under the effect of surfactin, providing a research foundation for this new harmful algal bloom mitigation method.

Regulatory effects of different anionic surfactants on the transformation of heavy metal fractions and reduction of heavy metal resistance genes in chicken manure compost

Surfactants are widely used as a passivating agent in heavy metal passivation process, but their effect on transformation of heavy metal fraction and reduction of heavy metal resistance genes (MRGs) in composting process is still unknown. The aim of this study was to compare the effects of two anionic surfactants (rhamnolipid and sodium dodecyl sulfate) on heavy metal passivation and resistance gene reduction in chicken manure composting. The results showed that the addition of surfactant can effectively enhance degradation of organic matter (OM). Both surfactants could effectively reduce the bioavailability of heavy metals (HMs) and the relative abundance of resistance genes, especially rhamnolipids. The potential functional bacteria affecting heavy metal passivation were identified by the changes of microbial community. Redundancy analysis (RDA) showed that protease (PRT) activity was the key factor affecting the fractions of the second group of HMs including ZnF1, CuF1, CuF2, PbF1 and PbF3. These findings indicate that addition of anionic surfactants can reduce the bioavailability of HMs and the abundance of resistance genes in compost products, which is of guiding significance for the reduction of health risks in the harmless utilization of livestock and poultry manure.

Microbial surfactants: characteristics, production and broader application prospects in environment and industry

Microbial surfactants are green molecules with high surface activities having the most promising advantages over chemical surfactants including their ability to efficiently reducing surface and interfacial tension, nontoxic emulsion-based formulations, biocompatibility, biodegradability, simplicity of preparation from low cost materials such as residual by-products and renewable resources at large scales, effectiveness and stabilization under extreme conditions and broad spectrum antagonism of pathogens to be part of the biocontrol strategy. Thus, biosurfactants are universal tools of great current interest. The present work describes the major types and microbial origin of surfactants and their production optimization from agro-industrial wastes in the batch shake-flasks and bioreactor systems through solid-state and submerged fermentation industries. Various downstream strategies that had been developed to extract and purify biosurfactants are discussed. Further, the physicochemical properties and functional characteristics of biosurfactants open new future prospects for the development of efficient and eco-friendly commercially successful biotechnological product compounds with diverse potential applications in environment, industry, biomedicine, nanotechnology and energy-saving technology as well.

Bioremediation of an industrial soil contaminated by hydrocarbons in microcosm system, involving bioprocesses utilizing co-products and agro-industrial wastes

The present study describes practical implication of bioaugmentation and biostimulation processes for bioremediation of an industrial soil chronically contaminated by hydrocarbons. For this purpose, biomass production of six autochthonous hydrocarbon-degrading bacteria were evaluated as inoculum of bioaugmentation strategy, by testing carbon and nitrogen sources included co-products and agro-industrial waste as sustainable and low-cost components of the growth medium. Otherwise, biostimulation was approached by the addition of optimized concentration of nitrogen and phosphorus. Microcosm assays showed that total hydrocarbons (TH) were significantly removed from chronically contaminated soil undergoing bioremediation treatment. Systems Mix (bioaugmentation); N,P (biostimulation) and Mix + N,P (bioaugmentation and biostimulation) reached higher TH removal, being 89.85%, 91.00%, 93.04%, respectively, comparing to 77.83% of system C (natural attenuation) at 90 days. The increased heterotrophic aerobic bacteria and hydrocarbon degrading bacteria counts were according to TH biodegrading process during the experiments. Our results showed that biostimulation with nutrients represent a valuable alternative tool to treat a chronically hydrocarbon-contaminated industrial soil, while bioaugmentation with a consortium of hydrocarbon degrading bacteria would be justified when the soil has a low amount of endogenous degrading microorganisms. Furthermore, the production of inoculum for application in bioaugmentation using low-cost substrates, such as industrial waste, would lead to the development of an environmentally friendly and attractive process in terms of cost-benefit.

Isolation and characterization of two glycolipopeptids biosurfactants produced by a Lactiplantibacillus plantarum OL5 strain isolated from green olive curing water

Microbial surfactants are natural amphiphilic compounds with high surface activities and emulsifying properties. Due to their structural diversity, low toxicity, biodegradability, and chemical stability in different conditions, these molecules are potential substitutes for chemical surfactants; their interest has grown significantly over the last decade. The current study focuses on the isolation, identification, and characterization of a lactic acid bacteria that produce two forms of biosurfactants. The OL5 strain was isolated from green olive fermentation and identified using MALDI/TOF and DNAr16S amplification. Emulsification activity and surface tension measurements were used to estimate biosurfactant production. The two biosurfactants derived from Lactiplantibacillus plantarum OL5 presented good emulsification powers in the presence of various oils. They were also shown to have the potential to reduce water surface tension from 69 mN/m to 34 mN/m and 37 mN/m within a critical micelle concentration (CMC) of 7 mg/ml and 1.8 mg/ml, respectively, for cell bound and extracellular biosurfactants. Thin layer chromatography (TLC) and FT-IR were used to analyze the composition of the two biosurfactants produced. the obtained data revealed that the two biomolecules consist of a mixture of carbohydrates, lipids and proteins. We demonstrated that they are two anionic biosurfactants with glycolipopeptide nature which are stable in extreme conditions of temperature, pH and salinity.

Remediation of oil-contaminated soil using Fe/Cu nanoparticles and biosurfactants

Oil (or petroleum), consisting of a mixture of hydrocarbons, can leak from oil exploration, production, and use. Due to their complex mixture and interaction with the subsurface soil and water, they are hard to treat and can become a significant environmental concern. Rhamnolipid and sophorolipid biosurfactants, biologically produced surfactants, can be used to remove petroleum hydrocarbons. Nanoparticles have gained attention as promising materials for soil remediation. In this study, suspensions of Fe-Cu nanoparticles and biosurfactants were employed for the remediation of oil-contaminated soil. The results showed that these suspensions displayed a high oil removal rate from contaminated soil, which followed the first-order reaction. For batch experiments, the oil remediation efficiency was up to 84%. Optimum conditions to achieve the highest oil remediation performance included a rhamnolipid biosurfactant: nanoparticle ratio of 10:1 (wt%: wt%), pH 7, room temperature, and shaking speed of 60 rpm for 60 min. The remediation rate was improved by higher temperature and lower ionic strength. In the presence and absence of nanoparticles, rhamnolipid biosurfactant demonstrated a higher remediation efficiency than sophorolipid biosurfactant and ultraplex surfactant. The presence of other surfactants decreased the treatment productivity by 9-14% compared to using only rhamnolipid biosurfactant. Nanoparticles were reused with a remediation efficiency of 59% after three cycles by rhamnolipid biosurfactant. These results suggested that biosurfactants/Fe-Cu nanoparticle suspension showed promise for the remediation of oil-contaminated soil.

Formation and structural features of micelles formed by surfactin homologues

Surfactin, a group of cyclic lipopeptides produced by Bacillus subtilis, possesses surfactant properties and is a promising natural and biologically active compound. In this study, we present a comprehensive characterization of surfactin, including its production, chromatographic separation into pure homologues (C₁₂, C₁₃, C₁₄, C₁₅), and investigation of their physicochemical properties. We determined adsorption isotherms and interpreted them using the Gibbs adsorption equation, revealing that the C₁₅ homologue exhibited the strongest surface tension reduction (27.5 mN/m), while surface activity decreased with decreasing carbon chain length (32.2 mN/m for C₁₂). Critical micelle concentration (CMC) were also determined, showing a decrease in CMC values from 0.35 mM for C₁₂ to 0.08 mM for C₁₅. We employed dynamic light scattering (DLS), transmission electron microscopy (TEM), and density functional theory (DFT) calculations to estimate the size of micellar aggregates, which increased with longer carbon chains, ranging from 4.7 nm for C₁₂ to 5.7 nm for C₁₅. Furthermore, aggregation numbers were determined, revealing the number of molecules in a micelle. Contact angles and emulsification indexes (E₂₄) were measured to assess the functional properties of the homologues, showing that wettability increased with chain length up to C₁₄, which is intriguing as C₁₄ is the most abundant homologue. Our findings highlight the relationship between the structure and properties of surfactin, providing valuable insights for understanding its biological significance and potential applications in various industries. Moreover, the methodology developed in this study can be readily applied to other cyclic lipopeptides, facilitating a better understanding of their structure-properties relationship.

Genome analysis of biosurfactant producing bacterium, Bacillus tequilensis

Bioremediation is crucial for recuperating polluted water and soil. By expanding the surface area of substrates, biosurfactants play a vital role in bioremediation. Biosurfactant-producing microbes release certain biosurfactant compounds, which are promoted for oil spill remediation. In the present investigation, a biosurfactant-producing bacterium Bacillus tequilensis was isolated from Chilika Lake, Odisha, India (latitude and longitude: 19.8450 N 85.4788 E). Whole-Genome Sequencing (WGS) of Bacillus tequilensis was carried out using Illumina NextSeq 500. The size of the whole genome of Bacillus tequilensis was 4.47 MB consisting of 4,478,749 base pairs forming a circular chromosome with 528 scaffolds, 4492 protein-encoding genes (ORFs), 81 tRNA genes, and 114 ribosomal RNA transcription units. The total raw reads were 4209415, and the processed reads were 4058238 with 4492 genes. The whole genome obtained from the present investigation was used for genome annotation, variant calling, variant annotation, and comparative genome analysis with other existing Bacillus species. In this study, a pathway was constructed which describes the biosurfactant metabolism of Bacillus tequilensis. The study identified that genes such as SrfAD, SrfAC, SrfAA and SrfAB are involved in biosurfactant synthesis. The sequence of the genes SrfAD, SrfAC, SrfAA, SrfAB was deposited in GenBank database with accession MUG02427.1, MUG02428.1, MUG02429.1, MUG03515.1 respectively. The whole genome sequence was submitted to GenBank with an accession RMVO00000000 and the raw fastq reads were submitted to SRA, NCBI repository with an accession: SRX5023292.

Enhanced removal of mixed VOCs with different hydrophobicities by Tween 20 in a biotrickling filter: Kinetic analysis and biofilm characteristics

Mass transfer limitation usually causes the poor performance of biotrickling filters (BTFs) for the treatment of hydrophobic volatile organic compounds (VOCs) during long-term operation. In this study, two identical lab-scale BTFs were established to remove a mixture of n-hexane and dichloromethane (DCM) gases using non-ionic surfactant Tween 20 by Pseudomonas mendocina NX-1 and Methylobacterium rhodesianum H13. A low pressure drop (≤110 Pa) and a rapid biomass accumulation (17.1 mg g^-1) were observed in the presence of Tween 20 during the startup period (30 d). The removal efficiency (RE) of n-hexane was enhanced by 15.0%- 20.5% while DCM was completely removed with the inlet concentration (IC) of 300 mg·m^-3 at different empty bed residence times in the Tween 20 added BTF. The viable cells and the relative hydrophobicity of the biofilm were increased under the action of Tween 20, which facilitated the mass transfer and enhanced the metabolic utilization of pollutants by microbes. Besides, Tween 20 addition enhanced the biofilm formation processes including the increased extracellular polymeric substance (EPS) secretion, biofilm roughness and biofilm adhesion. The kinetic model simulated the removal performance of the BTF with Tween 20 for the mixed hydrophobic VOCs, and the goodness-of-fit was above 0.9.

Identification and functional analysis of non-coding regulatory small RNA FenSr3 in Bacillus amyloliquefaciens LPB-18

Bacillus amyloliquefaciens is an interesting microbe in the food processing and manufacturing industries. Non-coding small RNAs (sRNAs) have been shown to play a crucial role in the physiology and metabolism of bacteria by post-transcriptionally regulating gene expression. This study investigated the function of novel sRNA FenSr3 by constructing fenSr3 deficient strain and complementary strains in B. amyloliquefaciens LPB-18 , which were named LPN-18N and LPB-18P, respectively. The result showed significant differences in fengycin yield between strain LPB -18N and LPB-18P. The production of fengycin was significantly enhanced in B. amyloliquefaciens LPB-18N, compared with that of the strain LPB-18 from 190.908 mg/L to 327.598 mg/L. Moreover, the production of fengycin decreased from 190.464 mg/L to 38.6 mg/L in B . amyloliquefaciens LPB-18P. A comparative transcriptome sequencing was carried out to better understand the complex regulatory mechanism. Transcription analysis revealed that 1037 genes were differentially expressed between B. amyloliquefaciens LPB-18 and B. amyloliquefaciens LPB-18N, including the key regulatory genes in fatty acid, amino acid biosynthesis, and central carbon metabolism, which could provide sufficient quantities of building precursors for fengycin biosynthesis. The biofilm formation and sporulation was also enhanced in the strain LPB-18N, which indicates that FenSr3 could play a vital role in stress resistance and promotes survival in B. amyloliquefaciens. Some sRNAs involved in stress response have been identified in the literature, but their regulatory roles in fengycin production remain unclear. The study will contribute a novel perspective to the regulation mechanism of biosynthesis and the optimization of key metabolites of B. amyloliquefaciens.

Production and characterization of bioemulsifier by Parapedobacter indicus

The current study evaluated Parapedobacter indicus MCC 2546 for its potential to produce a bioemulsifier (BE). Screening methods performed for BE production by P. indicus MCC 2546 showed good lipase activity, positive drop collapse test, and oil-spreading activity. Furthermore, it showed maximum emulsification activity (225 EU/ml) and emulsification index (E24 50%) at 37°C in Luria Bertani broth at 72 h with olive oil as a substrate. The optimal pH and NaCl concentration for maximum emulsification activity were 7 and 1%, respectively. P. indicus MCC 2546 lowered the surface tension of the culture medium from 59.65 to 50.42 ± 0.78 mN/m. BE produced was composed of 70% protein and 30% carbohydrate, which showed the protein-polysaccharide nature of the BE. Furthermore, Fourier transform infrared spectroscopy analysis confirmed the same. P. indicus MCC 2546 showed a catecholate type of siderophore production. This is the first report on BE and siderophore production by the genus Parapedobacter.

Classical Molecular Dynamics Simulation of Glyonic Liquids: Structural Insights and Relation to Conductive Properties

Rhamnolipids are biosurfactants that have obtained wide industrial and environmental interests with their biodegradability and great surface activity. Besides their important roles as surfactants, they are found to function as a new type of glycolipid-based protic ionic liquids (ILs)─glyonic liquids (GLs). GLs are reported to have impressive physicochemical properties, especially superionic conductivity, and it was reported in experiments that specific ion selections and the fraction of water content have a strong effect on the conductivity. Also, the shape of the conductivity curve as a function of water fraction in GLs is interesting with a sharp increase first and a long plateau. We related the conductivities to the three-dimensional (3D) networks composed of -OH inside the GLs utilizing classical molecular dynamics (MD) simulations. The amount and size of these networks vary with both ion species and water fractions. Before reaching the first hydration layer, the -OH networks with higher projection/box length ratios indicate better conductivity; after reaching the first hydration layer and forming continuous structures, the conductivity retains with more water molecules participating in the continuous networks. Therefore, networks are found to be a qualitative predictor of actual conductivity. This is explained by the analysis of the atomic structures, including radial distribution function, fraction free volume, anion conformations, and hydrogen bond occupancies, of GLs and their water mixtures under different chemical conditions.

Unravelling the sponge microbiome as a promising source of biosurfactants

Microbial surfactants are particularly useful in bioremediation and heavy metal removal from soil and aquatic environments, amongst other highly valued uses in different economic and biomedical sectors. Marine sponge-associated bacteria are well-known producers of bioactive compounds with a wide array of potential applications. However, little progress has been made on investigating biosurfactants produced by these bacteria, especially when compared with other groups of biologically active molecules harnessed from the sponge microbiome. Using a thorough literature search in eight databases, the purpose of the review was to compile the current knowledge on biosurfactants from sponge-associated bacteria, with a focus on their relevant biotechnological applications. From the publications between the years 1995 and 2021, lipopeptides and glycolipids were the most identified chemical classes of biosurfactants. Firmicutes was the dominant phylum of biosurfactant-producing strains, followed by Actinobacteria and Proteobacteria. Bioremediation led as the most promising application field for the studied surface-active molecules in sponge-derived bacteria, despite the reports endorsed their use as antimicrobial and antibiofilm agents. Finally, we appoint some key strategies to instigate the research appetite on the isolation and characterization of novel biosurfactants from the poriferan microbiome.

Identifications of Surfactin-Type Biosurfactants Produced by Bacillus Species Isolated from Rhizosphere of Vegetables

Surfactins are cyclic lipopeptides consisting of a β-hydroxy fatty acid of variable chain length and a peptide ring of seven amino acids linked together by a lactone bridge, forming the cyclic structure of the peptide chain. These compounds are produced mainly by Bacillus species and are well regarded for their antibacterial, antifungal, and antiviral activities. For their surfactin production profiling, several Bacillus strains isolated from vegetable rhizospheres were identified by their fatty acid methyl ester profiles and were tested against phytopathogen bacteria and fungi. The isolates showed significant inhibition against of E. amylovora, X. campestris, B. cinerea, and F. culmorum and caused moderate effects on P. syringae, E. carotovora, A. tumefaciens, F. graminearum, F. solani, and C. gloeosporioides. Then, an HPLC-HESI-MS/MS method was applied to simultaneously carry out the quantitative and in-depth qualitative characterisations on the extracted ferment broths. More than half of the examined Bacillus strains produced surfactin, and the MS/MS spectra analyses of their sodiated precursor ions revealed a total of 29 surfactin variants and homologues, some of them with an extremely large number of peaks with different retention times, suggesting a large number of variations in the branching of their fatty acid chains.

An Overview on the Treatment of Oil Pollutants in Soil Using Synthetic and Biological Surfactant Foam and Nanoparticles

Oil-contaminated soil is one of the most concerning problems due to its potential damage to human, animals, and the environment. Nanoparticles have effectively been used to degrade oil pollution in soil in the lab and in the field for a long time. In recent years, surfactant foam and nanoparticles have shown high removal of oil pollutants from contaminated soil. This review provides an overview on the remediation of oil pollutants in soil using nanoparticles, surfactant foams, and nanoparticle-stabilized surfactant foams. In particular, the fate and transport of oil compounds in the soil, the interaction of nanoparticles and surfactant foam, the removal mechanisms of nanoparticles and various surfactant foams, the effect of some factors (e.g., soil characteristics and amount, nanoparticle properties, surfactant concentration) on remediation efficiency, and some advantages and disadvantages of these methods are evaluated. Different nanoparticles and surfactant foam can be effectively utilized for treating oil compounds in contaminated soil. The treatment efficiency is dependent on many factors. Thus, optimizing these factors in each scenario is required to achieve a high remediation rate while not causing negative effects on humans, animals, and the environment. In the future, more research on the soil types, operating cost, posttreatment process, and recycling and reuse of surfactants and nanoparticles need to be conducted.

Novel Organic Solvent Nanofiltration Approaches for Microbial Biosurfactants Downstream Processing

Glycolipid biosurfactants are the most prominent group of microbial biosurfactants, comprising rhamnolipids, sophorolipids and mannosylerythritol lipids (MELs). Usually, large amounts of hydrophobic substrates (e.g., vegetable oils) are used to achieve high titers (~200 g/L) of a crude product of low purity at values limited to 50-60%, contaminated with unconsumed triacylglycerol and residual free fatty acids and monoacylglycerides. The methods reported for the removal of these contaminants use a mixture of organic solvents, compromising solvent recyclability and increasing final process costs. This study reports, for the first time, an innovative downstream method for MELs, in which 90% of the triacylglycerols are separated from the crude MEL mixture in a first stage and the other lipid derivatives (free fatty acids, mono- and diacylglycerols) are removed by organic solvent nanofiltration (OSN). Three commercially available membranes (GMT-oNF-2, PuraMEm-600 and DuramMem-500) and several homemade membranes, casted from 22, 24 or 26% (w/v) polybenzimidazole (PBI) solutions, were assessed for crude MELs purification by diafiltration. A final purity of 87-90% in the MELs was obtained by filtering two diavolumes of methanol or ethyl acetate solutions through a PBI 26% membrane, resulting in MELs losses of 14.7 ± 6.1% and 15.3 ± 2.2%, respectively. Higher biosurfactant purities can be archived using the PBI 26% membrane at higher DV, but at the cost of higher product losses. Namely, in MeOH, the use of 6 DV leads to losses of 32% for MELs and 18% for sophorolipids. To obtain MELs at reagent grade with purities equal or higher than 97%, a two-sequential cascade filtration approach was implemented using the commercial membrane, GMT-oNF. In such a process, MELs with 98% purity was obtained at the cost of 11.6% MELs losses. Finally, decoloration, important in some applications, was successfully assessed using activated carbon. Overall, this study reports a unique solution for microbial biosurfactants production with minimal product losses, enabling solvent recycling and potentially reducing costs.

Green surfactants for corrosion control: Design, performance and applications

Surfactants enjoy an augmented share of hydrophilicity and hydrophobicity and are well-known for their anticorrosive potential. The use of non-toxic surfactants is gaining growing interest because of the scaling demands of green chemistry. Green surfactants have successfully replaced traditional toxic surfactant-based corrosion inhibitors. Recently, many reports described the corrosion inhibition potential of green surfactants. The present article aims to describe the recent advancements in using green surfactants in corrosion mitigation. They create a charge transfer barrier through their adsorption at the interface of the metal and the environment. Their adsorption is well explained by the Langmuir adsorption isotherm. In the adsorbed layer, their hydrophilic polar heads orient toward the metal side and their hydrophobic tails orient toward the solution side. They block the active sites and retard the anodic and cathodic and act as mixed-type inhibitors. Their adsorption and bonding nature are fruitfully supported by surface analyses. They can form mono- or multilayers depending upon the nature of the metal, electrolyte and experimental conditions. The challenges and opportunities of using green surfactants as corrosion inhibitors have also been described.

Phytoremediation of industrial effluents assisted by plant growth promoting bacteria

Industrialization plays a crucial role in the economic development of a country; however, the effluents produced as a byproduct generally contain toxic substances which are detrimental to living organisms. In this regard, it is essential to treat these toxic effluents before exposing them to the natural environment by selecting the most appropriate method accordingly. Several techniques are used to remediate industrial effluents including physical, chemical, and biological. Although some physical and chemical remediation technologies are of substantially important in remediation of industrial effluents, however, these technologies are either expensive to be applied by developing countries or not suitable for remediation of all kinds of effluents. In contrast, biological remediation is cost effective, nature friendly, and easy to use for almost all kinds of effluents. Among biological remediation strategies, phytoremediation is considered to be the most suitable method for remediation of industrial effluents; however, the phytoremediation process is slow, takes time in application and some effluents even affect plants growth and development. Alternately, plant microbe interactions could be a winning partner to remediate industrial effluents more efficiently. Among the microbes, plant growth promoting bacteria (PGPB) not only improve plant growth but also help in degradation, sequestration, volatilization, solubilization, mobilization, and bioleaching of industrial effluents which subsequently improve the phytoremediation process. The current study discusses the role of PGPB in enhancing the phytoremediation processes of industrial effluents.

A Systematic Review on Biosurfactants Contribution to the Transition to a Circular Economy

Since they are more environmentally acceptable than their chemically synthesized counterparts, biosurfactants are used in a wide range of environmental applications. However, less research has been done on biosurfactants within the context of the circular economy, despite their theoretical potential to fulfill a number of circular economy ambitions, including closing the consumption loop, regenerating natural systems, and maintaining resource value within the system. Hence, the main objective of this review is to identify and analyze the contributions of biosurfactants to the implementation of the circular economy. A final sample of 30 papers from the Web of Science database was examined. We identified five broad categories of contributions: waste stream-derived production, combating food waste, strengthening soil health, and improving the efficiency of water resources. We concluded that, while manufacturing biosurfactants from waste streams can reduce production costs, optimizing yield remains a contentious issue that complicates the adoption of biosurfactants into the circular economy framework.

Polycyclic aromatic hydrocarbons remobilization from contaminated porous media by (bio)surfactants washing

Biosurfactants, surface-active agents produced by microorganisms, are increasingly studied for their potential use in soil remediation processes because they are more environmentally friendly than their chemically produced homologues. In this work, we report on the use of a crude biosurfactant produced by a bacterial consortium isolated from a PAHs-contaminated soil, compared with other (bio)surfactants (Tween80, Sodium dodecyl sulfate - SDS, rhamnolipids mix), to wash PAHs from a contaminated porous media. Assays were done using columns filled with sand or sand-clay mixtures (95:5) spiked with four model PAHs. The crude biosurfactant showed less adsorption to the [sand] and the [sand + clay] columns compared to Tween 80, SDS and the rhamnolipid mix. The biosurfactant showed the second best capacity to remove PAHs from the columns (as dissolved and particulate phases), both from [sand] and [sand + clay], after SDS when applied at lower concentrations than the other sufactants. The effluent concentrations of phenanthrene (PHE), pyrene (PYR) and benzo[a]pyrene (BAP) increased in the presence of the crude biosurfactant. Compared to the control experiment using only water, the global PAHs washed mass (amount of PAHs removed from the columns) increased between 9 and 1000 times for PHE and BAP in the [sand] column, and between 55 and 6000 times respectively for PHE and BAP in the [sand + clay] columns. Moreover, in the [sand + clay] columns, leaching of a part of the clays was observed in the SDS and the biosurfactant injections assays. This clay leaching resulted in higher PAHs removal, due not to desorption but rather to particulate transport. In the context of washing PAH-contaminated soils in biopiles or subsurface remediation, our results could help in sizing the remediation approach using an environmental friendly biosurfactant, before a pump-and-treat process.

Dodecenylsuccinic anhydride-modified oxalate decarboxylase loaded with magnetic nano-Fe3O4@SiO2 for demulsification of oil-in-water emulsions

The inability to demulsify oil-in-water emulsions via green and efficient processes is a challenging problem in many industrial processes. As a novel biodemulsifier, protein demulsifiers display excellent dispersibility and stability, but their demulsification mechanisms are not clear, which severely restricts their large-scale production and application. In this study, the demulsification mechanism of the high-efficiency protein biodemulsifier oxalate decarboxylase (Bacm OxdC), which is secreted by the Bacillus mojavensis XH1 strain, for an oil-in-water emulsion was analyzed. The results showed that Bacm OxdC was spontaneously adsorbed at the oil-water interface and turned its hydrophobic amino acids outward to increase its hydrophobicity and break the emulsified system. Furthermore, it effectively reduced the oil-water interfacial tension and interfacial film strength, thereby reducing the oil-water interfacial energy and finally enabling demulsification. To further improve the demulsification efficiency and reusability, Fe₃O₄@SiO₂@OxdC-DDSA was prepared. This method provided a magnetic response for Bacm OxdC and enabled efficient demulsification. The demulsification rate of Fe₃O₄@SiO₂@OxdC-DDSA reached 98.1% at 24 h, which was 30.7% higher than that of the original Bacm OxdC. After three cycles, the demulsification rate still reached 89.3%, proving it has excellent recyclability. This work is the first study on the demulsification mechanism of protein biodemulsifiers and provides useful insights into the demulsification mechanism of biodemulsifiers for oil-in-water emulsions. In addition, a promising high-efficiency modification technique for protein biodemulsifiers was proposed, which provided information for the development of biodemulsifiers for oil-water separation.

Bioremediation of Petroleum-Contaminated Soils with Biosurfactant-Producing Degraders Isolated from the Native Desert Soils

A crude oil spill in 2014 resulted in extensive soil contamination of the hyper arid Evrona Nature Reserve in Israel's Negev Desert. The contaminated soils became highly hydrophobic, threatening the existence of plants in the habitat. We hypothesized that bioaugmenting the soil with indigenous biosurfactant-producing, hydrocarbon-degrading bacteria (HDB) would accelerate the reduction in the soil's hydrophobicity. We aimed to isolate and characterize biosurfactant-producing HDBs from the desert-contaminated soil and test if they can be used for augmenting the soil. Twelve hydrocarbon-degrading strains were isolated, identified as Pseudomonas, and classified as biosurfactants "producing" and "nonproducing". Inoculating 10⁹ CFU/g of "producing" strains into the polluted soil resulted in a 99.2% reduction in soil hydrophobicity within seven days. At the same time, nonproducing strains reduced hydrophobicity by only 17%, while no change was observed in the untreated control. The microbial community in the inoculated soil was dominated by the introduced strains over 28 days, pointing to their persistence. Rhamnolipid biosynthesis gene rhlAB remained persistent in soil inoculated with biosurfactants, indicating in situ production. We propose that the success of the treatment is due to the use of inoculum enriched from the polluted soil.

A review of the role of biosurfactants in the biodegradation of hydrophobic organopollutants: production, mode of action, biosynthesis and applications

The increasing influence of human activity and industrialization has adversely impacted the environment via pollution with organic contaminants, which are minimally soluble in water. These hydrophobic organopollutants may be present in sediment, water or biota and have created concern due to their toxic effects in mammals. The ability of microorganisms to degrade pollutants makes their use the most effective, inexpensive and ecofriendly method for environmental remediation. Microorganisms have the ability to produce natural surfactants (biosurfactants) that increase the bioavailability of hydrophobic organopollutants, which enables their use as carbon and energy sources. Due to microbial diversity in production, and the biodegradability, nontoxicity, stability and specific activity of the surfactants, the use of microbial surfactants has the potential to overcome problems associated with contamination by hydrophobic organopollutants.This review provides an overview of the current state of knowledge regarding microbial surfactant production, mode of action in the biodegradation of hydrophobic organopollutants and biosynthetic pathways as well as their applications using emergent strategy tools to remove organopollutants from the environment. It is also specified for the first time that biosurfactants are produced either as growth-associated products or secondary metabolites, and are produced in different amounts by a wide range of microorganisms.

Guava Seed Oil: Potential Waste for the Rhamnolipids Production

Guava is consumed in natura and is also of considerable importance to the food industry. The seeds and peel of this fruit are discarded, however, guava seeds yield oil (~13%) that can be used for the bioproducts synthesis. The use of a by-product as a carbon source is advantageous, as it reduces the environmental impact of possible harmful materials to nature, while adding value to products. In addition, the use of untested substrates can bring new yield and characterization results. Thus, this research sought to study rhamnolipids (RLs) production from guava seed oil, a by-product of the fructorefinery. The experiments were carried out using Pseudomonas aeruginosa LBI 2A1 and experimental design was used to optimize the variables Carbon and Nitrogen concentration. Characterization of RLs produced occurred by LC-MS. In this study, variables in the quadratic forms and the interaction between them influenced the response (p < 0.05). The most significant variable was N concentration. Maximum RLs yield achieved 39.97 g/L, predominantly of mono-RL. Characterization analysis revealed 9 homologues including the presence of RhaC10C14:2 (m/z 555) whose structure has not previously been observed. This research showed that guava seed oil is an alternative potential carbon source for rhamnolipid production with rare rhamnolipid homologues.

Wetting Properties of Rhamnolipid and Surfactin Mixtures with Triton X-165

The wetting properties of the rhamnolipid and surfactin mixtures with Triton X-165 were considered based on the contact angle measurements of their aqueous solution on the polytetrafluoroethylene (PTFE), polymethyl methacrylate (PMMA) and quartz (Q) surfaces. The obtained contact angle isotherms were described by the exponential function of the second order as well as by Szyszkowski equation in some cases. Using the contact angle isotherms of individual biosurfactants and TX165 as well as the earlier obtained isotherms of their surface tension the contact angle isotherms of the biosurfactants mixtures with TX165 were deduced. As follows the presence of the maxima on the contact angle isotherms of the biosurfactants mixtures with TX165 is justified. They do not prove negative adsorption of the biosurfactant and TX165 at the interfaces. However, the mutual exchange of the biosurfactant and TX165 molecules is observed in the layers at the interfaces. The concentration of the studied mixtures at the PTFE-solution interface was established to be close to that at the solution-air one but that at the PTFE-air is equal to zero. However, the concentration of the studied mixtures at the PMMA-solution and quartz-solution is greater than zero. The concentration at the PMMA(quartz)-air and PMMA(quartz)-solution interfaces is smaller than that at the solution-air one.

Synthetic Routes for Designing Furanic and Non Furanic Biobased Surfactants from 5-Hydroxymethylfurfural

5-hydroxymethylfurfural (HMF) is one of the most valuable biomass platform molecules, enabling the construction of a plethora of high value-added furanic compounds. In particular, in the last decade, HMF has been considered as a starting material for designing biobased surfactants, not only because of its renewability and carbon footprint, but also because of its enhanced biodegradability. This Review presents recent examples of the different approaches to link the hydrophilic and lipophilic moieties into the hydrophobic furan (and tetrahydrofuran) ring, giving a variety of biobased surfactants that have been classified here according to the charge of the head polar group. Moreover, strategies for the synthesis of different non-furanic structures surfactant molecules (such as levulinic acid, cyclopentanols, and aromatics) derived from HMF are described. The new HMF-based amphiphilic molecules presented here cover a wide range of hydrophilic-lipophilic balance values and have suitable surfactant properties such as surface tension activity and critical micelle concentration, to be an important alternative for the replacement of non-sustainable surfactants.

Enhanced biodegradation of hexachlorocyclohexane (HCH) isomers by Sphingobium sp. strain D4 in the presence of root exudates or in co-culture with HCH-mobilizing strains

Lindane and other 1,2,3,4,5,6-hexachlorocyclohexane (HCH) isomers are persistent organic pollutants highly hydrophobic, which hampers their availability and biodegradation. This work aimed at (i) investigating genes encoding enzymes involved in HCH degradation in the bacterium Sphingobium sp. D4, (ii) selecting strains, from a collection of environmental isolates, able to mobilize HCHs from contaminated soil, and (iii) analysing the biodegradation of HCHs by strain D4 in co-culture with HCH-mobilizing strains or when cultivated with root exudates. Fragments of the same size and similar sequence to linA and linB genes were successfully amplified. Two isolates, Streptomyces sp. M7 and Rhodococcus erythropolis ET54b able to produce emulsifiers and to mobilize HCH isomers from soil were selected. Biodegradation of HCH isomers by strain D4 was enhanced when co-inoculated with HCH mobilizing strains or when cultivated with root exudates. The degrader strain D4 was able to decompose very efficiently HCHs isomers, reducing their concentration in soil slurries by more than 95% (from an average initial amount of 50 ± 8 mg HCH kg^-1 soil) in 9 days. The combination of HCH-degrading and HCH-mobilizing strains can be considered a promising inoculum for future soil bioremediation studies using bioaugmentation techniques or in combination with plants in rhizodegradation assays.