Modification of collagen with a natural cross-linker, procyanidin

Enhancement of chitosan-based film physicochemical and storage properties by interaction with proanthocyanidin and natural deep eutectic solvent

Deep eutectic solvent (DES) has been recognized as a promising plasticizer for the preparation of biodegradable food packaging films. In addition, DES-plasticized chitosan (CS) films could also serve as a favorable carrier for loading active components. In this work, a ternary composite film was fabricated by plasticizing chitosan with DES and the active ingredient proanthocyanidin (PA) was used as a cross-linking agent. The incorporation of PAs significantly enhanced the toughness, elasticity, and hydrophobicity of the ternary CS-DES-PA composite films. It achieved antioxidant and bacteriostatic functions. In particular, the ternary CS-DES-PA composite films had a thickness of 0.16 ± 0.01 μm, a tensile strength of 2.63 ± 0.48 MPa, and an elongation about 73.22 %. They also have improved water resistance, UV blocking, with a high-water contact angle of 88.4° and a low water swelling of 5 % on the surface of the film. Meanwhile, the PAs in the film could slow down the browning of litchi fruits. This ternary blended film (CS-DES-PA) achieves better compatibility of the active ingredient in the film-forming substrate. It also provides a green and biodegradable packaging material for food packaging.

Effects on dentin nanomechanical properties, cell viability and dentin wettability of a novel plant-derived biomodification monomer

OBJECTIVES

To evaluate the effects of dentin biomodification agents (Proanthocyanidin (PAC), Cardol (CD) and Cardol-methacrylate (CDMA) on dentin hydrophilicity by contact angle measurement, viability of dental pulp stem cells (DPSCs) and nanomechanical properties of the hybrid layer (HL).

METHODS

CDMA monomer was synthesized from cardol through methacrylic acid esterification. Human extracted third molars were used for all experiments. For nanomechanical tests, specimens were divided in four groups according to the primer solutions (CD, CDMA, PAC and control) were applied before adhesive and composite coating. Nanomechanical properties of the HL were analyzed by nanoindentation test using a Berkovich probe in a nanoindenter. Wettability test was performed on dentin surfaces after 1 min biomodification and measured by contact angle analysis. Cytotoxicity was assessed by a MTT assay with DPSCs after 48 and 72 h. Data were analyzed with Student's t test or Two-way ANOVA and Tukey HSD test (p < 0.05).

RESULTS

CD and CDMA solutions achieved greater hydrophobicity and increased the water-surface contact angles when compared to PAC and control groups (p < 0.05). PAC group showed a greater reduction of elastic modulus in nanoindentation experiments when compared to CD and CDMA groups (p < 0.05) after 4 months of aging. CD inhibited cell proliferation compared to all further materials (p < 0.05), whilst CDMA and PAC indicated no cell cytotoxicity to human DPSCs.

SIGNIFICANCE

Cardol-methacrylate provided significantly higher hydrophobicity to dentin and demonstrated remarkable potential as collagen crosslinking, attaining the lowest decrease of HL's mechanical properties. Furthermore, such monomer did not affect pulp cytotoxicity, thereby highlighting promising feasibility for clinical applications.

Assessing the impact of different Urushiol primer solvents on dentin remineralization and bond strength

OBJECTIVES

To investigate urushiol's potential as a dentin cross-linking agent, promoting remineralization of etched dentin and preventing activation of endogenous proteases causing collagen degradation within the hybrid layer. The goal is to improve bond strength and durability at the resin-dentin interface.

METHODS

Urushiol primers with varying concentrations were prepared using ethanol and dimethyl sulfoxide (DMSO) as solvents. Dentin from healthy molars underwent grinding and acid etching for 15 s, followed by a 1min application of urushiol primer. After 14 and 28 days of remineralization incubation and remineralization were used to assess by Attenuated Total Reflection Fourier Transform Infrared spectroscopy (ATR-FTIR), Micro-Raman spectroscopy, X-ray Diffraction (XRD), Atomic Force Microscopy (AFM), Vickers Hardness, Scanning Electron Microscopy (SEM), and Energy X-ray dispersive spectroscopy (EDS). The overall performance of urushiol primers as dentin adhesives was observed by microtensile bond strength (μTBS) testing and nanoleakage assessment. Investigated the inhibitory properties of the urushiol primers on endogenous metalloproteinases (MMPs) utilizing in situ zymography, and the cytotoxicity of the primers was tested.

RESULTS

Based on ATR-FTIR, Raman, XRD, EM-EDS and Vickers hardness analyses, the 0.7%-Ethanol group significantly enhanced dentin mineral content and improved mechanical properties the most. Pretreatment notably increased the μTBS of restorations, promoted the stability of the mixed layer, and reduced nanoleakage and MMPs activity after 28 days.

SIGNIFICANCE

The urushiol primer facilitates remineralization in demineralized dentin, enhancing remineralization in etched dentin, effectively improving the bonding interface stability, with optimal performance observed at a 0.7 wt% concentration of the urushiol primer.

A comparison of different cleaning approaches for blood contamination after curing universal adhesives on the dentine surface

OBJECTIVE

This study compared the effectiveness of various cleaning approaches, including spray rinsing, repreparing with diamond burs, and using phosphoric acid or sodium hypochlorite alone or with polyphenols (resveratrol or myricetin), in removing blood contamination from the dentine after adhesive light-curing.

METHODS

The contact angles of the treated surfaces were measured and scanning electron microscopy/ energy dispersive X-ray spectroscopy observation was performed. The bond strength and nanoleakage were assessed, and in situ zymography was performed before and after aging. Interactions between matrix metalloproteinase (MMP)-9 and polyphenols were evaluated using molecular dynamics and rhMMP-9 inhibition analyses. The destruction of sodium hypochlorite on collagen and the resistance of polyphenols-treated dentine collagen to enzymolysis were evaluated using the hydroxyproline (HYP) assay. The effect of polyphenols on dentine collagen crosslinking was assessed by Fourier Transform Infrared Spectroscopy.

RESULTS

The repreparation group had the lowest contact angle compared to the other groups. The spray rinsing group had the lowest bond strength and highest amounts of nanoleakage. Cleaning with phosphoric acid or sodium hypochlorite alone removed the blood contaminants and parts of the adhesive; moreover, applying polyphenols further improved the bond strength and decreased nanoleakage and MMP activity after aging. Both polyphenols inhibited rhMMP-9 activity and promoted collagen crosslinking. Sodium hypochlorite showed the maximum HYP release when used alone, which was decreased after adding polyphenols.

SIGNIFICANCE

Phosphoric acid or sodium hypochlorite cleaning can remove blood contamination from the dentine surface after adhesive curing, and the addition of polyphenols can improve the durability of dentine bonding.

Prodelphinidins enhance dentin matrix properties and promote adhesion to methacrylate resin

OBJECTIVE

Investigate the bioactivity and stability of Rhodiola rosea (RR) fractions as a natural source of prodelphinidin gallate (PDg) on dentin collagen via analysis of the viscoelastic and resin-dentin adhesive properties of the dentin matrix.

METHODS

The biomimicry and stability of RR subfractions (F1, F2, F3 and F4) with collagen were determined by dynamic mechanical analysis (DMA). DMA used a strain sweep method to assess the dentin matrix viscoelastic properties [storage (E'), loss (E"), and complex (E*) moduli and tan δ] after treatment, 7-, 30- and 90-days of storage in simulated body fluids (SBF). Resin-dentin interface properties were assessed after 1 and 90-days in SBF by microtensile bond strength test and confocal laser scanning microscopy. Data were analyzed using two and one-way ANOVA and post-hoc tests (α = 0.05).

RESULTS

RR fractions increased dentin matrix complex (96 - 69 MPa) and storage (95 - 68 MPa) moduli, compared to the control (∼9 MPa) in the ranking order: F2 ≥ F3 = F1 = F4 > control (p < 0.001). Treatment did not affect tan δ values. After 30- and 90-days, RR-treated dentin E*, E' and tan δ decreased (p < 0.001). F2 fraction yielded the highest microtensile bond strength (43.9 MPa), compared to F1, F4 (35.9 - 31.7 MPa), and control (29 MPa). RR-treated interfaces mediated stable surface modifications and enhanced collagen-methacrylate resin interactions at the bioadhesive interface.

SIGNIFICANCE

Prodelphinidin gallates from RR are potent and reasonably stable biomimetic agents to dentin. Higher potency of F2 fraction with the dentin matrix and the adhesive interface is associated with a degree of polymerization of 2-3 and gallo(yl) motifs.

Sustainable Collagen Film Preparation with Tannins Extracted from Moroccan Pomegranate Byproduct Varieties: Thermal, Structural, and Nanoscaled Studies

Recently, obtaining collagen films using a cross-linking technique has been a successful strategy. The current investigation used six cross-linker extracts (CE) from six different pomegranate varieties' byproducts to make and characterize collagen-tannin films using acid-soluble collagen (SC). The polymeric film has a yellow hue after CE incorporation. Fourier transform infrared spectroscopy assessed the impact of CE and its successful interaction within the matrix. The shifts verify different interactions between extracts and collagen functional groups, where they likely form new hydrogen bonds, retaining their helix structure without damaging the matrix. Scanning electron microscopy was used to analyze the morphology and fiber size. The average diameter of the fibers was found to be about 3.64 μm. Thermal behaviors (denaturation and degradation) were investigated by thermogravimetric analysis. The weight losses of cross-linked films increased by around 20% compared to non-cross-linked ones. This phenomenon was explained by the absence of telopeptide sections in the collagen helical structure, typically reinforced by lysine and hydroxylysine covalent linkages. Nanoscaled observations were also accomplished using transmission electron microscopy (TEM) on SC and SC-CE. The TEM analysis confirmed the CE polymerization degree effect on the cross-linking density via the overlap sequences, ranging up to 32.38 ± 2.37 nm on the fibril. The prepared biodegradable collagen-tannin film showed higher cross-linking density, which is expected to improve the biomaterial applications of collagen films while exploiting the underrated pomegranate byproducts.

Preliminary Evaluation of Bioactive Collagen-Polyphenol Surface Nanolayers on Titanium Implants: An X-ray Photoelectron Spectroscopy and Bone Implant Study

To endow an implant surface with enhanced properties to ensure an appropriate seal with the host tissue for inflammation/infection resistance, next-generation bone implant collagen-polyphenol nanolayers were built on conventional titanium surfaces through a multilayer approach. X-ray Photoelectron Spectroscopy (XPS) analysis was performed to investigate the chemical arrangement of molecules within the surface layer and to provide an estimate of their thickness. A short-term (2 and 4 weeks) in vivo test of bone implants in a healthy rabbit model was performed to check possible side effects of the soft surface layer on early phases of osteointegration, leading to secondary stability. Results show the building up of the different nanolayers on top of titanium, resulting in a final composite collagen-polyphenol surface and a layer thickness of about 10 nm. In vivo tests performed on machined and state-of-the-art microrough titanium implants do not show significant differences between coated and uncoated samples, as the surface microroughness remains the main driver of bone-to-implant contact. These results confirm that the surface nanolayer does not interfere with the onset and progression of implant osteointegration and prompt the green light for specific investigations of the potential merits of this bioactive coating as an enhancer of the device/tissue seal.

Theaflavin -3,3'-digallate/ethanol: a novel cross-linker for stabilizing dentin collagen

Objectives

To study the ability of theaflavin-3,3'-digallate (TF3)/ethanol solution to crosslink demineralized dentin collagen, resist collagenase digestion, and explore the potential mechanism.

Methods

Fully demineralized dentin blocks were prepared using human third molars that were caries-free. Then, these blocks were randomly allocated into 14 separate groups (n = 6), namely, control, ethanol, 5% glutaraldehyde (GA), 12.5, 25, 50, and 100 mg/ml TF3/ethanol solution groups. Each group was further divided into two subgroups based on crosslinking time: 30 and 60 s. The efficacy and mechanism of TF3's interaction with dentin type I collagen were predicted through molecular docking. The cross-linking, anti-enzymatic degradation, and biomechanical properties were studied by weight loss, hydroxyproline release, scanning/transmission electron microscopy (SEM/TEM), in situ zymography, surface hardness, thermogravimetric analysis, and swelling ratio. Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy were utilized to explore its mechanisms. Statistical analysis was performed using one and two-way analysis of variance and Tukey's test.

Results

TF3/ethanol solution could effectively crosslink demineralized dentin collagen and improve its resistance to collagenase digestion and biomechanical properties (p < 0.05), showing concentration and time dependence. The effect of 25 and 50 mg/ml TF3/ethanol solution was similar to that of 5% GA, whereas the 100 mg/mL TF3/ethanol solution exhibited better performance (p < 0.05). TF3 and dentin type I collagen are mainly cross-linked by hydrogen bonds, and there may be covalent and hydrophobic interactions.

Conclusion

TF3 has the capability to efficiently cross-link demineralized dentin collagen, enhancing its resistance to collagenase enzymatic hydrolysis and biomechanical properties within clinically acceptable timeframes (30 s/60 s). Additionally, it exhibits promise in enhancing the longevity of dentin adhesion.

Influences of Polyphenols on the Properties of Crosslinked Acellular Fish Swim Bladders: Experiments and Molecular Dynamic Simulations

Acellular fish swim bladders (AFSBs) are a promising biomaterial in tissue engineering, however, they may suffer from rapid degradation due to enzyme invasion. In this work, natural polyphenols, including epigallocatechin gallate (EGCG), proanthocyanidin (PC), tannic acid (TA) and protocatechuic acid (PCA), were utilized to improve the properties of AFSBs through crosslinking modifications. Fourier transform infrared (FTIR) results indicate that the triple helix of the collagen in AFSBs is well preserved after crosslinking. The differential scanning calorimetry (DSC), water contact angle (WCA) and in vitro degradation tests indicate that the polyphenol-crosslinked AFSBs exhibit improved thermal stability, enzymatic stability, hydrophilicity and mechanical properties. Among them, EGCG with multiple phenolic hydroxyl groups and low potential resistance is more favorable for the improvement of the mechanical properties and enzymatic stability of AFSBs, as well as their biocompatibility and integrity with the collagen triple helix. Moreover, the crosslinking mechanism was demonstrated to be due to the hydrogen bonds between polyphenols and AFSBs, and was affected by the molecular size, molecular weight and the hydroxyl groups activity of polyphenol molecules, as clarified by molecular dynamic (MD) simulations. The approach presented in this work paves a path for improving the properties of collagen materials.

Multimodal characterization of the collagen hydrogel structure and properties in response to physiologically relevant pH fluctuations

pH fluctuations within the extracellular matrix (ECM) and its principal constituent collagen, particularly in solid tumors and chronic wounds, may influence its structure and function. Whereas previous research examined the impact of pH on collagen fibrillogenesis, this study focuses on determining how pH fluctuations affect collagen hydrogels that mimic the physiological ECM. Utilizing a type I collagen hydrogel, we examined the influence of pH fluctuations on its structure, properties, and function while keeping the collagen hydrated. We show that collagen's secondary structure remains unaltered during pathologically relevant microenvironmental pH changes. By employing cryo scanning electron microscopy and artificial intelligence-assisted image analysis, we show that at physiological pH, collagen hydrogel presents densely packed, aligned, and elongated fibrils, which upon a decrease to pH 6.5, are transformed into shorter, sparser, and disoriented fibrils. The collagen possesses a higher storage modulus yet a lower permeability at pH 7 and 7.8 compared with pH 6.5 and 7.4. Exposing acidified collagen to a basic buffer reinstates its native structure and viscoelastic properties. Our study offers an innovative approach to analyze and characterize perturbations in hydrated collagen-based systems with potential implications for better understanding and combating disease progression. STATEMENT OF SIGNIFICANCE: As the main component of the extracellular matrix, collagen undergoes conformational changes associated with pH changes during disease. We analyze the impact of pH on pre-formed collagen fibers mimicking healthy tissues subjected to disease, and do not focus on the more studied fibrillogenesis process. Using cryogenic SEM, which allowed imaging close to the native state, we show that even minor fluctuations in the pH affect the collagen thickness, length, fiber alignment, and rheological properties. Following exposure to acidic pH, the collagen had short fibers, lacked orientation, and had low mechanical strength. This acidic collagen restored its original properties after returning to a neutral pH. These findings can help determine how pH changes can be modulated to restore healthy collagen properties.

Rapid deterioration in buried leather: archaeological implications

Understanding archaeological leather degradation helps inform economies, crafts, and technologies of historic communities. However, archaeological leather is at high risk of degradation due to deterioration and changes within the burial conditions. This research applied non-destructive FTIR-ATR to experimentally buried vegetable-tanned leather and archaeological leather excavated at the Roman site of Vindolanda, UK to explore survival, destruction, and preservation processes of tanned leather. Analyses focused on observing and monitoring changes in chemical functional groups related to leather tannins, collagen and lipid components following burial. FTIR-ATR results highlighted rapid changes following experimental burial in wet soil, tentatively associated with early onset microbial activity, which targeted readily available lipids but not tightly bound collagen. Prior to burial, differences in structural composition were present in leather spectra based on manufacture; however, following burial in wet soil, FTIR-ATR spectra indicated de-tanning occurs rapidly, especially in waterlogged conditions, with archaeological leather becoming more uniform and similar to untanned leather. Therefore, the comparison of FTIR-ATR results from archaeological leather to experimentally buried leather samples was informative for showing the destructive de-tanning in waterlogged environments. The comparison of FTIR-ATR data from modern unburied leather cannot be compared against archaeological samples. Importantly, despite de-tanning occurring soon after burial, the vegetable-tanning method promoted long-term preservation of leather in wet soil. The observed changes could not be directly associated with the proportion of condensed to hydrolysable tannin, suggesting alternate variables impacted the preservation. Furthermore, mineral components introduced into the leather through the animal skin, tannin material and/or tannin liquid are suggested to contribute to these changes. Crucially a high degree of heterogeneity in error results within the experimentally buried sample material underlined that any changes in collagen ratios cannot be overinterpreted and must be considered within the context of larger datasets.

Dexamethasone release from hyaluronic acid microparticle and proanthocyanidin-gelatin hydrogel in sciatic tissue regeneration

Biodegradable microparticles are useful vehicles for the controlled release of bioactive molecules in drug delivery, tissue engineering and biopharmaceutical applications. We developed dexamethasone (Dex) encapsulation into tyramine-substituted hyaluronic acid microparticles (Dex-HA-Tyr Mp) mediated by horseradish peroxidase (HRP) crosslinking using a microfluidic device and infollowing crosslinked gelatin (Gela) with proanthocyanidin (PA) as a semi-confined bed hydrogel for the repair of sciatic tissue injury. It was found that the simultaneous use of Dex-HA-Tyr Mp and cross-linked Gela-PA hydrogel improved the physical properties of the hydrogel, including mechanical strength and degradability. The designed composite also provided a sustained release system for Dex delivery to the surrounding sites, demonstrating the applicability of the fabricated hydrogel composite for sciatic nerve tissue engineering and regeneration. The encapsulated cells were viable and showed adequate growth ability and morphogenesis during prolonged incubation in Gela-PA/HA-Tyr Mp hydrogel compared to control conditions. Interestingly, histological analysis revealed a significant increase in the number of axons in the injured sciatic nerve following treatment with Dex-HA-Tyr Mp and injectable Gela-PA hydrogel compared to other control groups. In conclusion, the results demonstrated that fabricated Dex-loaded MPs and injectable hydrogel from biomimetic components are suitable systems for sustained delivery of Dex with adequate biocompatibility and the approach may have potential therapeutic applications in peripheral nerve regeneration.

Effects of Covalent or Noncovalent Binding of Different Polyphenols to Acid-Soluble Collagen on Protein Structure, Functionality, and Digestibility

In this study, the structure, function, and digestibility of noncovalent complexes and covalent conjugates formed by acid-soluble collagen with polyphenols of different structures (quercetin, epicatechin, gallic acid, chlorogenic acid, procyanidin, and tannic acid) were investigated. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) showed that polyphenols were covalently bound to collagen by laccase catalytic oxidation. Biolayer interferometry revealed that the noncovalent binding strength of polyphenols to collagen from high to low was quercetin > gallic acid > chlorogenic acid > epicatechin, which was consistent with the trend of covalent polyphenol binding. Procyanidin and tannic acid had strong noncovalent binding, but their covalent binding ability was weak. Compared with the pure collagen, the complexes improved emulsification and antioxidant properties (more than 2.5 times), and the conjugates exhibited better thermal stability (99.4-106.8 °C) and antidigestion ability (reduced by more than 37%). The finding sheds new light on the use of collagen as a functional food ingredient in the food industry.

Construction of ultrasonically treated collagen/silk fibroin composite scaffolds to induce cartilage regeneration

A novel tissue-specific functional tissue engineering scaffold for cartilage repair should have a three-dimensional structure, good biosafety and biological activity, and should be able to promote cartilage tissue regeneration. This study aimed to determine the effect of ultrasound-treated collagen/silk fibroin (Col/SF) composite scaffolds with good mechanical properties and high biological activity on cartilage repair. The characteristics of the scaffolds with different Col/SF ratios (7:3, 8:2, and 9:1) were determined by scanning electron microscopy, Fourier-transform infrared spectroscopy, and porosity, water absorption, and compression tests. In vitro evaluations revealed the biocompatibility of the Col/SF scaffolds. Results suggested that the optimal ratio of Col/SF composite scaffolds was 7:3. The Col/SF scaffolds induced adipose-derived stem cells to undergo chondrogenic differentiation under chondrogenic culture conditions. The efficiency of Col/SF scaffolds for cartilage regeneration applications was further evaluated using an in vivo model of full-thickness articular cartilage defects in New Zealand rabbits. The Col/SF scaffolds effectively promoted osteochondral regeneration as evidenced by macroscopic, histological, and immunohistochemical evaluation. The study demonstrates that ultrasound-treated Col/SF scaffolds show great potential for repairing cartilage defects.

Construction of functional surfaces for dental implants to enhance osseointegration

Dental implants have been extensively used in patients with defects or loss of dentition. However, the loss or failure of dental implants is still a critical problem in clinic. Therefore, many methods have been designed to enhance the osseointegration between the implants and native bone. Herein, the challenge and healing process of dental implant operation will be briefly introduced. Then, various surface modification methods and emerging biomaterials used to tune the properties of dental implants will be summarized comprehensively.

Packaging films based on biopolymers from seafood processing wastes: Preparation, properties, and their applications for shelf-life extension of seafoods-A comprehensive review

Biopolymers derived from seafood processing byproducts are used to prepare active and biodegradable films as the packaging of food products. These films possess bioactivities to enhance the shelf life of packed foods by proactively releasing antimicrobial/antioxidative agents into the foods and providing sufficient barrier properties. Seafood processing byproducts are an eminent source of valuable compounds, including biopolymers and bioactive compounds. These biopolymers, including collagen, gelatin, chitosan, and muscle proteins, could be used to prepare robust and sustainable food packaging with some antimicrobial agents or antioxidants, for example, plant extracts rich in polyphenols or essential oils. These active packaging are not only biodegradable but also prevent the deterioration of packed foods caused by spoilage microorganisms as well as chemical deterioration. Seafood discards have a promising benefit for the development of environmentally friendly food packaging systems via the appropriate preparation methods or techniques. Therefore, the green packaging from seafood leftover can be better exploited and replace the synthetic counterpart.

NDGA enhances the physicochemical and anti-biodegradation performance of dentin collagen

OBJECTIVES

Collagen fibrils from carious dentin matrix are prone to enzymatic degradation. This study investigates the feasibility and mechanism of nordihydroguaiaretic acid (NDGA), as a collagen crosslinker, to bio-modify the demineralized dentin matrix.

METHODS

The physicochemical properties of the crosslinked dentin matrix were characterized by swelling ratio, ninhydrin assay, Fourier Transform Infrared spectroscopy, and atomic force microscopy. The collagenase degradation resistance was evaluated by measuring loss of dry mass, hydroproline release, loss of elasticity, and micro-nano structure integrity. The cytotoxicity of NDGA-crosslinked dentin collagen was evaluated by flow cytometry.

RESULTS

NDGA crosslinked dentin matrix without destroying the integrity of collagen. Mechanistically, NDGA formed bisquinone bond between two adjacent o-quinone groups, resulting in NDGA polymeric matrix in which collagen fibrils were embedded. NDGA modification could significantly enhance the stiffness of dentin matrix at macro-nano scale. The NDGA-crosslinked dentin matrix exhibited remarkably low collagen degradation and sustained bulk elasticity after collagenase challenge, which were attributed to decreased water content, physical masking of collagenase bind sites on collagen, and improved stiffness of collagen fibrils. Notably, NDGA-crosslinked dentin matrix exhibited excellent biocompatibility.

CONCLUSION

NDGA, as a biocompatible collagen crosslinker, improves the mechanical properties and biodegradation resistance of demineralized dentin matrix.

Fabrication and performance evaluation of PLCL-hCOLIII small-diameter vascular grafts crosslinked with procyanidins

Cardiovascular disease has become one of the main causes of death. It is the common goal of researchers worldwide to develop small-diameter vascular grafts to meet clinical needs. Collagen is a valuable biomaterial that has been used in the preparation of vascular grafts and has shown good results. Recombinant humanized collagen (RHC) has the advantages of clear chemical structure, batch stability, no virus hazard and low immunogenicity compared with animal-derived collagen, which can be developed as vascular materials. In this study, Poly (l-lactide- ε-caprolactone) with l-lactide/ε-caprolactone (PLCL) and type III recombinant humanized collagen (hCOLIII) were selected as raw materials to prepare vascular grafts, which were prepared by the same-nozzle electrospinning apparatus. Meanwhile, procyanidin (PC), a plant polyphenol, was used to cross-link the vascular grafts. The physicochemical properties and biocompatibility of the fabricated vascular grafts were investigated by comparing with glutaraldehyde (GA) crosslinked vascular grafts and pure PLCL grafts. Finally, the performance of PC cross-linked PLCL-hCOLIII vascular grafts were evaluated by rabbit carotid artery transplantation model. The results indicate that the artificial vascular grafts have good cell compatibility, blood compatibility, and anti-calcification performance, and can remain unobstructed after 30 days carotid artery transplantation in rabbits. The grafts also showed inhibitory effects on the proliferation of SMCs and intimal hyperplasia, demonstrating its excellent performance as small diameter vascular grafts.

Dual-functional etchants that simultaneously demineralize and stabilize dentin render collagen resistant to degradation for resin bonding

OBJECTIVES

To develop dual-functional etchants that could demineralize and stabilize dentin collagen simultaneously, and to assess the effects of these etchants on collagen crosslinking, biostability and resin bonding properties under clinically relevant conditions.

METHODS

Dual-functional etchants were prepared by mixing 56% glycolic acid and 17% phosphoric acid and adding 1% of theaflavins (TF) or proanthocyanidins from grape seed extract (GSE). The etchant without crosslinker was used as control. The prepared human dentin specimens were treated with the 3 etchants for 30 s and analyzed for chemical interaction using Fourier transform infrared spectroscopy and resistance of the demineralized layer to collagenase degradation using electron microscopy (EM). Resin-dentin interfacial bonding properties were evaluated after 24 h and after 10,000 thermocycling through microtensile bond strength (μTBS), nanoleakage and matrix metalloproteinases (MMPs) activity via in situ zymography. Statistical analysis was done using ANOVA and post- hoc Tuckey's test.

RESULTS

Compared to control, TF and GSE dual-functional etchants were able to demineralize dentin, induce collagen crosslinking and protect the demineralized layer from collagenase degradation within 30 s. High resolution EM images showed better protection with TF etchant compared to GSE. There was a significant reduction in μTBS and an increase in nanoleakage and MMPs activity in control after thermocycling (p < 0.05) while these changes weren't seen in dual-functional etchants.

SIGNIFICANCE

Dual-functional etchants, especially TF containing, provide collagen protection against degradation and result in stable μTBS and less nanoleakage and MMPs activity under clinically relevant conditions.

Effect of Different Crosslinkers on Denatured Dentin Collagen's Biostability, MMP Inhibition and Mechanical Properties

OBJECTIVE

Sound, natural dentin collagen can be stabilized against enzymatic degradation through exogenous crosslinking treatment for durable bonding; however, the effect on denatured dentin (DD) collagen is unknown. Hence, the ability of different crosslinkers to enhance/restore the properties of DD collagen was assessed.

METHODS

Demineralized natural and DD collagen films (7 mm × 7 mm × 7 µm) and beams (0.8 mm × 0.8 mm × 7 mm) were prepared. DD collagen was experimentally produced by heat or acid exposure, which was then assessed by various techniques. All specimens were then treated with 1 wt% of chemical crosslinker 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide/n-hydroxysuccinimide (EDC/NHS) and two structurally different flavonoids-theaflavins (TF) from black tea and type-A proanthocyanidins from cranberry juice (CR) for either 30 s or 1 h. The controls were untreated. Dentin films were assessed for chemical interaction and cross-linking effect by FTIR, biostability against exogenous collagenase by weight loss (WL) and hydroxyproline release (HYP), and endogenous matrix metalloproteinases (MMPs) activity by confocal laser microscopy. Dentin beams were evaluated for tensile properties. Data were analyzed using ANOVA and Tukey's test (α = 0.05).

RESULTS

Compared with natural collagen, DD collagen showed pronounced structural changes, altered biostability and decreased mechanical properties, which were then improved to various degrees that were dependent on the crosslinkers used, with EDC/NHS being the least effective. Surprisingly, the well-known MMP inhibitor EDC/NHS showed negligible effect on or even increased MMP activity in DD collagen. As compared with control, cross-linking induced by TF and CR significantly increased collagen biostability (reduced WL and HYP release, p < 0.05), MMP inhibition (p < 0.001) and mechanical properties (p < 0.05), regardless of denaturation.

CONCLUSIONS

DD collagen cannot or can only minimally be stabilized via EDC/NHS crosslinking; however, the challenging substrate of DD collagen can be enhanced or restored using the promising flavonoids TF and CR.

Glutaraldehyde-based desensitizers' influence on bonding performances and dentin enzymatic activity of universal adhesives

OBJECTIVES

To evaluate the influence of two glutaraldehyde-based desensitizers (L: GLUMA Desensitizer, Heraeus Kulzer and G: GLUMA Desensitizer PowerGel) prior to the adhesive procedures on microtensile bond strength (µTBS) to dentin and endogenous enzymatic activity.

METHODS

Noncarious human third molars (N = 48) were cut to expose middle coronal dentin. Six experimental groups were formed according to the dentin pre-treatment (L or G) and the universal adhesives (IBU - iBond universal, Kulzer or AU - Adhese Universal, Ivoclar Vivadent) used in the self-etch mode (n = 8): 1) L/IBU; 2) G/IBU; 3) IBU; 4) L/AU; 5) G/AU; 6) AU. Specimens were cut into sticks and stressed until failure after 24 h (T0) or 1 yr of aging (T12). Additional 4 teeth were used for in situ zymography evaluation and data were statistically analyzed (α = 0.05).

RESULTS

Dentin pre-treatment, adhesive and aging statistically influenced bond strength and enzymatic activity (P<0.001). AU demonstrated higher bond strength values than IBU (P<0.001). The L resulted in higher bond strength compared to the G and control groups (P<0.001). aging statistically influenced bonding performance, especially when no dentin pre-treatment was performed (P<0.001). In situ zymography revealed that at baseline the control groups exhibited lower interfacial fluorescence compared to the experimental groups, irrespective of the adhesive used (P<0,001). However, after 1 yr of artificial storage, no differences were found among the groups (P>0.05).

CONCLUSIONS

Glutharldeadeyde-based products increased bond strength and determined a stabilization of the adhesive interface over time apparently not related to the MMPs inhibition.

CLINICAL SIGNIFICANCE

The results of this in vitro study suggest that the application of glutaraldehyde-based desensitizers prior to the adhesive procedures when associated with universal adhesives could result in increased bond strength and stabilization of the adhesive interface over time.

Multifilament Collagen Fiber Bundles with Tendon-like Structure and Mechanical Performance

Collagen multifilament bundles comprised of thousands of monofilaments are prepared by multipin contact drawing of an entangled polymer solution consisting of collagen and poly(ethylene oxide) (PEO). The multifilament bundles are hydrated in graded concentrations of PEO and phosphate buffered saline (PBS) to promote assembly of collagen fibrils within each monofilament while preserving the structure of the multifilament bundle. Multiscale structural characterization reveals that the hydrated multifilament bundle contains properly folded collagen molecules packed in collagen fibrils containing microfibrils, staggered by exactly one-sixth of the microfibril D-band spacing to produce a periodicity of 11 nm. Sequence analysis predicts that in this structure, phenylalanine residues are close enough within and between microfibrils to become ultraviolet C (UVC) crosslinked. In agreement with this analysis, the ultimate tensile strength (UTS) and Young's modulus of the hydrated collagen multifilament bundles crosslinked by UVC radiation increase nonlinearly with total UVC energy to reach values in the range of native tendons without damage to the collagen molecules. This fabrication method recapitulates the structure of a tendon across multiple length scales and offers tunability in tensile properties using only collagen molecules and no other chemical additives in addition to PEO, which is almost entirely removed during the hydration process.

Effects of proanthocyanidins and dialdehyde chitosan on the proliferation and differentiation of bovine myoblast for cultured meat production

Cultured meat technology intends to manufacture meat by cultivating muscle stem cells in vitro, which is an emerging methodology in meat production. However, the insufficient stemness of bovine myoblasts cultivated in vitro declined the ability of cell expansion and myogenic differentiation, which limited the production of cultured meat. Therefore, in this study, we introduced proanthocyanidins (PC, natural polyphenolic compounds) and dialdehyde chitosan (DAC, natural polysaccharides) to explore the effects of proliferation and differentiation of bovine myoblasts in vitro. The experiment results revealed that PC and DAC promoted cell proliferation by improving the transition from G1 to the S phase as well as cell division in G2. Meanwhile, the myogenic differentiation of cells was further boosted by the combined PC and DAC up-regulation of MYH3 expression. Moreover, the study revealed the synergistic effect of PC and DAC on enhancing the structural stability of collagen, and bovine myoblasts demonstrated excellent growth and dispersion ability on collagen scaffolds. It is concluded that both PC and DAC promote the proliferation and differentiation of bovine myoblasts, contributing to the development of cultured meat production systems.

The roles of theaflavins in reducing dentin erosion

This study aimed to evaluate the effect of theaflavins [TFs] on the process of dentin erosion and investigation the potential mechanism. For erosion kinetics of the dentin, 7 experimental groups (n = 5) treated with 10% ethanol [EtOH] (negative control) are erosion for 1, 2, 3, 4, 5, 6, and 7 d erosion cycles (4 cycles/d). For the effect of TFs on dentin erosion, 6 experimental groups (n = 5) were treated with 1% epigallocatechin gallate [EGCG], 1% chlorhexidine [CHX], 1%, 2%, 4%, and 8% TFs for the 30 s and then subjected to erosion cycles (4 cycles/d for 7 d). The erosive dentin wear (μm) and surface morphology were evaluated and compared by laser scanning confocal microscope and scanning electron microscopy. The matrix metalloproteinase inhibition effects of TFs were investigated using in situ zymography and molecular docking. TFs-treated collagen was investigated by ultimate microtensile strength, Fourier-transform infrared spectroscopy, and molecular docking. Data were analyzed by ANOVA, Tukey's test (P < 0.05). The TFs-treated groups (7.56 ± 0.39, 5.29 ± 0.61, 3.28 ± 0.33, and 2.62 ± 0.99 μm for 1%, 2%, 4%, and 8% TFs) had significantly lower erosive dentin wear than the negative control group (11.23 ± 0.82 μm), and the effect was concentration-dependent at low concentrations (P < 0.05). TFs inhibit matrix metalloproteinase [MMP]. Moreover, TFs crosslink dentin collagen and cause hydrophilic changes in dentin collagen. TFs preserve organic matrix within the demineralized dentin by inhibiting MMP activity and simultaneously improving collagen's resistance to enzymes, both of which contribute to preventing or slowing down the progression of dentin erosion.

Crosslinking Improve Demineralized Dentin Performance and Synergistically Promote Biomimetic Mineralization by CaP_PILP

OBJECTIVE

to explore the effects of optimal crosslinking (chemical treatment) on demineralized dentin matrix and the possible synergism with calcium phosphate polymer-induced liquid precursor (CaP-PILP) bionic remineralization (physical treatment), and offer benefit to the clinic of resin-dentin bonding and dentin hypersensitivity.

METHODS

demineralized dentin was treated with glutaraldehyde (GA), carbodiimide (EDC), and procyanidin (PA) for crosslinking, followed by CaP-PILP biomimetic remineralization. The morphology, surface mechanical and physio-chemical properties, and enzymatic resistance were evaluated regardless of the modification.

RESULTS

the collagen fibers appeared morphologically complete with higher surface microhardness and characteristic peaks of amide I-III bands were visible after GA, PA, and EDC crosslinking. Collagen collapse and dissolution were seen in untreated demineralized dentin with enzyme attack, while the collagen fiber structure remained intact in GA- and PA-treated specimens. The lamellar mineral phase was visible at 2 days and the dentin tubules were almost completely enclosed at 4-6 days after PA crosslinking and mineralization. However, demineralized collagen fibers and open tubules were still visible between the dentinal tubules on day 8 in the control group.

CONCLUSION

the structure integrity, enzyme resistance, and mechanical properties of the collagen fiber network could be significantly preserved by GA and PA crosslinking than EDC and no treatment. While, strongest synergistic effects were observed in PA on bionic remineralization by CaP-PILP, and further significantly improve the quality and shorten the duration of mineralization. These findings would be beneficial for dental clinical practice of resin-dentin bonding and dentin hypersensitivity.

Polyphenols Can Improve Resin-Dentin Bond Durability by Promoting Amorphous Calcium Phosphate Nanoparticles to Backfill the Dentin Matrix

Objective

To investigate the effects of proanthocyanidins (PA), myricetin, resveratrol, and kaempferol on the modification of dentin collagen and the inhibition of matrix metalloproteinase (MMP) activity, and to evaluate their contributions to the biomimetic remineralization and resin-dentin bonding performance.

Methods

Attenuated total reflection Fourier transform infrared spectroscopy (ATR-FTIR) and in situ zymography were applied to verify the collagen modification and MMP activity inhibition induced by these four polyphenols. Scanning electron microscopy/energy dispersive spectrometer (SEM/EDS) analysis, X-ray diffraction (XRD), ATR-FTIR, Vickers hardness numbers (VHN), and micro-computed tomography (micro-CT) were performed to characterize the remineralized dentin. Microtensile bond strength (μTBS) and nanoleakage were investigated to evaluate the effects of the four polyphenols on resin-dentin bonding durability.

Results

ATR-FTIR and in situ zymography confirmed that these four polyphenols could modify dentin collagen and inhibit MMP activity, respectively. Chemoanalytic characterization exhibited the efficacies of the four polyphenols in promoting dentin biomimetic remineralization. The surface hardness of PA-pretreated dentin was the greatest. Micro-CT results demonstrated that the PAs group possessed the highest amount of dentin surface minerals and the lowest amount of deep-layer minerals. The surface and deep-layer mineral contents of the Myr group were higher than Res and Kae groups. Treatment with these four polyphenols significantly increased the initial μTBS compared with the control group without primer conditioning. μTBS decreased significantly during aging, and the decrease was more severe in the PAs and Kae groups than in the Myr and Res groups. With or without aging, the polyphenol groups exhibited relatively less fluorescence. However, the Myr and Res groups showed less serious nanoleakage after aging.

Conclusion

PA, myricetin, resveratrol, and kaempferol can modify dentin collagen, inhibit MMP activity, promote biomimetic remineralization, and improve resin-dentin bond durability. Compared with PA and kaempferol, myricetin and resveratrol are more effective in improving resin-dentin bonding.

Are Natural Compounds a Promising Alternative to Synthetic Cross-Linking Agents in the Preparation of Hydrogels?

The main aim of this review is to assess the potential use of natural cross-linking agents, such as genipin, citric acid, tannic acid, epigallocatechin gallate, and vanillin in preparing chemically cross-linked hydrogels for the biomedical, pharmaceutical, and cosmetic industries. Chemical cross-linking is one of the most important methods that is commonly used to form mechanically strong hydrogels based on biopolymers, such as alginates, chitosan, hyaluronic acid, collagen, gelatin, and fibroin. Moreover, the properties of natural cross-linking agents and their advantages and disadvantages are compared relative to their commonly known synthetic cross-linking counterparts. Nowadays, advanced technologies can facilitate the acquisition of high-purity biomaterials from unreacted components with no additional purification steps. However, while planning and designing a chemical process, energy and water consumption should be limited in order to reduce the risks associated with global warming. However, many synthetic cross-linking agents, such as N,N'-methylenebisacrylamide, ethylene glycol dimethacrylate, poly (ethylene glycol) diacrylates, epichlorohydrin, and glutaraldehyde, are harmful to both humans and the environment. One solution to this problem could be the use of bio-cross-linking agents obtained from natural resources, which would eliminate their toxic effects and ensure the safety for humans and the environment.

Collagen and Silk Fibroin as Promising Candidates for Constructing Catalysts

A catalyst determines the mechanism of an organic chemical reaction, thus enabling the commercially viable formation of desired material products. Biopolymers offer new opportunities for the construction of catalysts by virtue of their biocompatibility, environmental benignity, and sustainability, as well as their low cost. Biopolymers are especially useful as carriers and precursors in catalysis application. The employment of biocompatible and biosustainable collagen and silk fibroin materials will revolutionize state-of-the-art electronic devices and systems that currently rely on conventional technologies. In this review, we first consider the ordered hierarchical structure, origin, and processing methods of collagen and silk fibroin. Then, the unique advantages and applicability of collagen and silk fibroin for constructing catalysts are summarized. Moreover, a summary of the state-of-the-art design, fabrication, and application of collagen- and silk fibroin-based catalysts, as well as the application of collagen- and silk-based catalysts, is presented by focusing on their roles as carriers and precursors, respectively. Finally, challenges and prospects are assessed for the construction and development of collagen and silk fibroin-based catalysts.

Sustainable metal-free leather manufacture via synergistic effects of triazine derivative and vegetable tannins

Restrictions on heavy metals, especially chromium, have encouraged alternative tanning systems that can reduce environmental and human health risks from conventional chrome-based tanning. In this work, metal-free combination tanning was developed by using vegetable tannins and a triazine-based syntan containing active chlorine groups (SACC). Specifically, the relationship between leather performance (e.g., hydrothermal stability and organoleptic properties) and technical protocols (e.g., types and dose of tannins) was systematically established. The optimized protocol involving a unique procedure (i.e., 10% SACC pre-tanning, shaving, and 25% wattle tanning) endowed the leather with high shrinkage temperature (~ 92 °C) and met the Chinese standards for shoe upper leather (QB/T 1873-2010). Our method not only produces zero chrome-containing solid wastes, but also uses ~ 75% less tannin for leather manufacture. The excellent leather performance was ascribed to the synergistic effects, where SACC and wattle diffused into collagen fibrils and may bind to collagen via covalent, hydrogen and ionic bonding, locking the hierarchical structure of collagen from microfibrils to fiber bundles. Moreover, we summarized these findings and proposed a diffusion-binding-locking mechanism, providing new insights for current tanning theory. Together with the biodegradable spent tanning liquor, this approach will underpin the development of sustainable leather manufacture.

Graphical Abstract

Effect of chitosan-oleuropein nanoparticles on dentin collagen cross-linking

BACKGROUND

The integrity and stability of collagen are crucial for the dentin structure and bonding strength at dentin-resin interface. Natural plant-derived polypehenols have been used as collagen crosslinkers.

OBJECTIVE

The aims of the study were to develop novel chitosan oleuropein nanoparticles (CS-OL-NPs), and to investigate the CS-OL-NPs treated dentin's the resistance to enzymatic degradation and mechanic property.

METHODS

CS-OL-NPs were developed using the ionotropic gelation method. Release and biocompatibility of the CS-OL-NPs were tested. Twenty demineralized dentin collage specimens were randomized into four interventions groups: A, Deionized Water (DW); B, 5% glutaraldehyde solution (GA); C, 1 mg/ml chitosan (CS); and D, 100 mg/L CS-OL-NPs. After 1-min interventions, dentin matrix were evaluated by the micro-Raman spectroscopy for the modulus of elasticity test. Collagen degradation was assessed using hydroxyproline (HYP) assay.

RESULTS

CS-OL-NPs were spherical core-shape with a size of 161.29 ± 8.19 nm and Zeta potential of 19.53 ± 0.26 mV. After a burst release of oleuropein in the initial 6 h, there was a long-lasting steady slow release. CS-OL-NPs showed a good biocompatibility for the hPDLSCs. The modulus of elasticity in the crosslinked groups were significantly higher than that in the control group (P< 0.05 for all). The specimens treated with CS-OL-NP showed a greater modulus of elasticity than those treated with GA and CS (P< 0.05 for both). The release of HYP in the crosslinked group was significantly lower than that in the non-crosslinked groups (P< 0.05 for all).

CONCLUSION

CS-OL-NPs enhanced the dentin mechanical property and resistance to biodegradation, with biocompatibility and potential for clinical application.

Salivary esterases dramatically reduce biostability of dentin collagen treated with galloylated polyphenols

OBJECTIVE

To investigate the effects of salivary esterases on biostability of collagen treated by galloylated polyphenols.

METHODS

Human dentin was microtomed into 6-μm-thick films, which were demineralized and treated for 60 s using solutions containing 0.6% and 2% of one of the crosslinkers: tannic acid (TAC), epigallocatechin gallate (EGCG), epigallocatechin (EGC), and N-[3-dimethylaminopropyl]-N'-ethylcarbodiimide hydrochloride (EDC)/N-hydroxysuccinimide (NHS), and for 1 h using EDC/NHS. Half of the treated and untreated (control) films were subjected to human saliva incubation. Collagen biostability was assessed via exogenous protease biodegradation by weight loss and hydroxyproline release, and endogenous MMPs by in situ zymography. The degradation products of galloylated polyphenols (TAC and EGCG) by saliva were monitored using proton nuclear magnetic resonance (1H NMR) and gel permeation chromatography (GPC). The esterase activity of saliva induced by the crosslinkers was also assessed.

RESULTS

Collagen films treated with TAC and EGCG exhibited significantly improved biostability (p < 0.05); however, the enhanced biostability was severely reduced after saliva incubation (p < 0.001). For EDC/NHS treated collagen, saliva incubation showed negligible effect on the biostability. 1H NMR studies confirmed the esterase-catalyzed hydrolysis of the galloyl. GPC measurements showed decreased molecular weight of TAC in saliva indicating its chemical degradation. Both TAC and EGCG showed much higher esterase activity than other treatment groups.

SIGNIFICANCE

The galloyl group plays important role in collagen crosslinking, inducing higher biostability. However, galloylated polyphenols crosslinked on collagen are highly susceptible to metabolism of human saliva by salivary esterase, dramatically compromising the enhanced biostability.

Evaluation of structural integrity effect on adhesion strength of root dentin with a multi-functional irrigation strategy

OBJECTIVES

To evaluate effects of a novel auxiliary irrigation strategy, proanthocyanidin (PA) + carboxymethyl chitosan/amorphous calcium phosphate (CMC/ACP) nanocomplexes, on maintaining the organic-inorganic structural integrity and hence optimizing the adhesion strength of root dentin.

MATERIALS AND METHODS

Dentin specimens (n = 150) were prepared and subjected to the classical irrigating strategy with or without PA and CMC/ACP. The ultrastructure and biomechanical behaviour of dentin were characterized by scanning electron microscopy and atomic force microscope, respectively. Forty single root-canal premolars were employed for push-out bond strength testing. Besides, the antibacterial effects against Enterococcus faecalis were evaluated with confocal laser scanning microscopy. Statistical differences were verified with one-way ANOVA and Tukey's post-tests.

RESULTS

The organic-inorganic structural integrity of root dentin was repaired with the synergetic use of PA and CMC/ACP. Correspondingly, the bond stability between the root canal wall and the AH-Plus sealer was significantly reinforced (P < 0.05). Meanwhile, the tissue biomechanical properties and antibacterial behaviour were enhanced compared to that of control group (P < 0.05).

CONCLUSIONS

The synergistic utilization of PA and CMC/ACP can preserve the structural integrity of root dentin, contributing to optimizing the sealing effects of root canal. Moreover, the novel irrigation strategy demonstrated a favourable antimicrobial activity.

CLINICAL RELEVANCE

The combination of PA and CMC/ACP can serve as a promising auxiliary irrigation strategy to optimize the outcomes of chemical preparation, enhance the sealing effects of root canal and hence improve the success rate of treatment.

Structure and properties of gelatin edible film modified using oxidized poly(2-hydroxyethyl acrylate) with multiple aldehyde groups

BACKGROUND

Pure gelatin film usually exhibits characteristics of being brittle and hydrophilic, which limit its wide use in food packing fields. In this study gelatin/oxidized poly(2-hydroxyethylacrylate) (G/OP) composite films were prepared using casting techniques, the aim of this research was to investigate the effects of OP on the structures and properties of the G/OP composite films.

RESULTS

The Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy results indicated that the G/OP films retained their original secondary structure and random coiled conformation. However, the surface and cross-sectional morphologies of the G/OP films were rougher than those of pure gelatin films, cracks and agglomerates appeared with increasing OP dosage. The remarkable transparency of the G/OP film at 280 nm indicated excellent ultraviolet (UV) light barrier properties of the film, which inhibited UV-light-induced food oxidation. Moreover, the addition of OP decreased the water content and water solubility and considerably increased the water contact angle of pure gelatin films from 78.8° to 116.2° (a maximum increase of 37.5°). This suggested that OP modification improved the hydrophobicity of gelatin films. Furthermore, the inclusion of OP significantly promoted the flexibility of gelatin films, thereby improving their brittleness.

CONCLUSIONS

The UV light barrier properties, hydrophobicity, and flexibility of gelatin films were improved via OP modification, thus the produced G/OP composite films have the potential to be used in food packaging. © 2022 Society of Chemical Industry.

Polyphenol-Enriched Extract of Lacquer Sap Used as a Dentine Primer with Benefits of Improving Collagen Cross-Linking and Antibacterial Functions

Commercial dentin adhesive systems are applied to restorations due to their resistant bonding properties, but they suffer from the lack of bioactivity and are prone to hydrolysis. Therefore, to overcome these limitations, an eco-friendly natural monomer, urushiol, was adopted to be a primer in dentin bonding due to its interaction with collagen and antibacterial activity, preventing further hydrolysis development. First, urushiol was determined to be capable of improving the biological stability of dentin collagen through cross-linking. Using high-fidelity analytical chemistry techniques, such as Fourier transform infrared spectroscopy, we quantified the effects of urushiol on collagen molecules. It could also effectively decrease weight loss after collagenase ingestion by improving the stability of dentin. Moreover, urushiol inhibited Streptococcus mutans growth as well as its biofilm formation. Finally, we demonstrated that the urushiol primer could improve the bonding strength, particularly after aging. The cross-linking and antibacterial functions of urushiol have provided promising developmental prospects for biomaterials in dentin adhesion.

Utilizing Fish Skin of Ikan Belida (Notopterus lopis) as a Source of Collagen: Production and Rheology Properties

Collagen hydrogels have been extensively applied in biomedical applications. However, their mechanical properties are insufficient for such applications. Our previous study showed improved mechanical properties when collagen was blended with alginate. The current study aims to analyze the physico-chemical properties of collagen-alginate (CA) films such as swelling, porosity, denaturation temperature (Td), and rheology properties. Collagen was prepared from discarded fish skin of Ikan Belida (Notopterus lopis) that was derived from fish ball manufacturing industries and cross-linked with alginate from brown seaweed (Sargasum polycystum) of a local species as a means to benefit the downstream production of marine industries. CA hydrogels were fabricated with ratios (v/v) of 1:1, 1:4, 3:7, 4:1, and 7:3 respectively. FTIR spectrums of CA film showed an Amide I shift of 1636.12 cm−1 to 1634.64 cm−1, indicating collagen-alginate interactions. SEM images of CA films show a porous structure that varied from pure collagen. DSC analysis shows Td was improved from 61.26 °C (collagen) to 83.11 °C (CA 3:7). CA 4:1 swelled nearly 800% after 48 h, correlated with the of hydrogels porosity. Most CA demonstrated visco-elastic solid characteristics with greater storage modulus (G′) than lost modulus (G″). Shear thinning and non-Newtonian behavior was observed in CA with 0.4% to 1.0% (w/v) CaCl2. CA hydrogels that were derived from discarded materials shows promising potential to serve as a wound dressing or ink for bio printing in the future.

An exploration of enhancing thermal stability of leather by hydrophilicity regulation: effect of hydrophilicity of phenolic syntan

Effect of retanning on the thermal stability of leather is eliciting increasing attention. However, the relationship between the hydrophilicity of retanning agents and the heat resistance of leather and the corresponding mechanism remain unclear. Herein, phenolic formaldehyde syntans (PFSs) were selected as models to explore the effect of the hydrophilicity of retanning agents on the thermal stability of retanned leather. The thermal stability of leather was closely correlated to the hydrophilic group content (sulfonation degree) of PFSs. As the sulfonation degree increased, the water absorption rate of PFSs and their retanned leathers decreased, whereas the thermal stability of leather increased. Molecular dynamics simulation results proved that the introduction of PFSs could reduce the binding ability of collagen molecules with water and thus decreased the water molecules around the PFS-treated collagen. These results may provide guidance for the tanners to select retanning agents reasonably to improve the thermal stability of leather.

Graphical Abstract

Dialdehyde Starch Nanocrystals as a Novel Cross-Linker for Biomaterials Able to Interact with Human Serum Proteins

In recent years, new cross-linkers from renewable resources have been sought to replace toxic synthetic compounds of this type. One of the most popular synthetic cross-linking agents used for biomedical applications is glutaraldehyde. However, the unreacted cross-linker can be released from the materials and cause cytotoxic effects. In the present work, dialdehyde starch nanocrystals (NDASs) were obtained from this polysaccharide nanocrystal form as an alternative to commonly used cross-linking agents. Then, 5-15% NDASs were used for chemical cross-linking of native chitosan (CS), gelatin (Gel), and a mixture of these two biopolymers (CS-Gel) via Schiff base reaction. The obtained materials, forming thin films, were characterized by ATR-FTIR, SEM, and XRD analysis. Thermal and mechanical properties were determined by TGA analysis and tensile testing. Moreover, all cross-linked biopolymers were also characterized by hydrophilic character, swelling ability, and protein absorption. The toxicity of obtained materials was tested using the Microtox test. Dialdehyde starch nanocrystals appear as a beneficial plant-derived cross-linking agent that allows obtaining cross-linked biopolymer materials with properties desirable for biomedical applications.

Polyphenols: Bioavailability, Microbiome Interactions and Cellular Effects on Health in Humans and Animals

Polyphenolic compounds have a variety of functions in plants including protecting them from a range of abiotic and biotic stresses such as pathogenic infections, ionising radiation and as signalling molecules. They are common constituents of human and animal diets, undergoing extensive metabolism by gut microbiota in many cases prior to entering circulation. They are linked to a range of positive health effects, including anti-oxidant, anti-inflammatory, antibiotic and disease-specific activities but the relationships between polyphenol bio-transformation products and their interactions in vivo are less well understood. Here we review the state of knowledge in this area, specifically what happens to dietary polyphenols after ingestion and how this is linked to health effects in humans and animals; paying particular attention to farm animals and pigs. We focus on the chemical transformation of polyphenols after ingestion, through microbial transformation, conjugation, absorption, entry into circulation and uptake by cells and tissues, focusing on recent findings in relation to bone. We review what is known about how these processes affect polyphenol bioactivity, highlighting gaps in knowledge. The implications of extending the use of polyphenols to treat specific pathogenic infections and other illnesses is explored.

Phosphoric acid containing proanthocyanidin enhances bond stability of resin/dentin interface

Proanthocyanidin (PA) is a promising dentin biomodifier due to its ability to stabilize collagen fibrils against degradation by matrix metalloproteinases (MMPs); however, the most effective protocol to incorporate PA into bonding procedures is still unclear. This study evaluated the effect of dentin biomodification with a PA acid etchant on MMP activity, adhesive interface morphology and resin-dentin microtensile bond strength. Sound extracted human molars were flattened to expose dentin and acid-etched for 15 s according to the groups: EXP - experimental phosphoric acid; EXP+PA - experimental phosphoric acid 10% PA; TE - total-etching system; SE - self-etching system. Samples were restored with composite resin and stored in distilled water (37ºC). MMP activity and interface morphology were analyzed after 24 h by in situ zymography (n=6) and scanning electron microscopy (n=3), respectively. The resin-dentin microtensile bond strength (μTBS) was evaluated after 24 h and 6 months storage (n=6). Significantly higher MMP activity was detected in etched dentin compared with untreated dentin (p<0.05), but no difference among acid groups was found. Resin tags and microtags, indicative of proper adhesive system penetration in dentinal tubules and microtubules, were observed along the hybrid layer in all groups. There was no difference in μTBS between 24 h and 6 months for EXP+PA; moreover, it showed higher long-term μTBS compared with TE and EXP (p<0.05). The results suggest that 15 s of biomodification was not sufficient to significantly reduce MMP activity; nonetheless, EXP+PA was still able to improve resin-dentin bond stability compared with total- and self-etching commercial systems.

[Effects of different crosslinking treatments on the properties of decellularized small intestinal submucosa porous scaffolds]

OBJECTIVE

To compare the effects of three different crosslinkers on the biocompatibility, physical and chemical properties of decellularized small intestinal submucosa (SIS) porous scaffolds.

METHODS

The SIS porous scaffolds were prepared by freeze-drying method and randomly divided into three groups, then crosslinked by glutaraldehyde (GA), 1-ethyl-3-(3-dimethylaminopropyl) carbodi-imide (EDC) and procyanidine (PA) respectively. To evaluate the physicochemical property of each sample in different groups, the following experiments were conducted. Macroscopic morphologies were observed and recorded. Microscopic morphologies of the scaffolds were observed using field emission scanning electron microscope (FESEM) and representative images were selected. Computer software (ImageJ) was used to calculate the pore size and porosity. The degree of crosslinking was determined by ninhydrin experiment. Collagenase degradation experiment was performed to assess the resistance of SIS scaffolds to enzyme degradation. To evaluate the mechanical properties, universal mechanical testing machine was used to determine the stress-strain curve and compression strength was calculated. Human bone marrow mesenchymal cells (hBMSCs) were cultured on the scaffolds after which cytotoxicity and cell proliferation were assessed.

RESULTS

All the scaffolds remained intact after different crosslinking treatments. The FESEM images showed uniformed interconnected micro structures of scaffolds in different groups. The pore size of EDC group[(161.90±13.44) μm] was significantly higher than GA group [(149.50±14.65) μm] and PA group[(140.10±12.06) μm] (P < 0.05). The porosity of PA group (79.62%±1.14%) was significantly lower than EDC group (85.11%±1.71%) and GA group (84.83%±1.89%) (P < 0.05). PA group showed the highest degree of crosslinking whereas the lowest swelling ratio. There was a significant difference in the swelling ratio of the three groups (P < 0.05). Regarding to the collagenase degradation experiment, the scaffolds in PA group showed a significantly lower weight loss rate than the other groups after 7 days degradation. The weight loss rates of GA group were significantly higher than those of the other groups on day 15, whereas the PA group had the lowest rate after 10 days and 15 days degradation. PA group showed better mechanical properties than the other two groups. More living cells could be seen in PA and EDC groups after live/dead cell staining. Additionally, the proliferation rate of hBMCSs was faster in PA and EDC groups than in GA group.

CONCLUSION

The scaffolds gained satisfying degree of crosslinking after three different crosslinking treatments. The samples after PA and EDC treatment had better physicochemical properties and biocompatibility compared with GA treatment. Crosslinking can be used as a promising and applicable method in the modification of SIS scaffolds.

Crosslinked Collagenic Scaffold Behavior Evaluation by Physico-Chemical, Mechanical and Biological Assessments in an In Vitro Microenvironment

Wound healing-associated difficulties continue to drive biotechnological creativeness into complex grounds. The sophisticated architecture of skin wound sites and the intricate processes involved in the response to the use of regenerative devices play a critical role in successful skin regeneration approaches and their possible outcomes. Due to a plethora of complications involved in wound healing processes as well as the coordination of various cellular mechanisms, biomimetic approaches seems to be the most promising starting ground. This study evaluates the behavior of a crosslinked, porous collagen scaffold obtained by lyophilization and dehydrothermal reticulation (DHT). We address the key physio-chemical and mechanical factors, such as swelling, density and porosity, mechano-dynamic properties, SEM and TG-DSC, as well as important biological outcomes regarding scaffold biocompatibility and cellular metabolic activity, cytokine expression in inflammation, apoptosis and necrosis, as well as hemocompatibility and biodegradation. The mechanical and visco-elastic behavior are correlated, with the samples found to present similar thermal behavior and increased rigidity after DHT treatment. High biocompatibility rates were obtained, with no inflammatory stimulation and a reduction in necrotic cells. Higher percentages of cellular early apoptosis were observed. The hemocompatibility rate was under 2%, coagulation effects expressed after 4 min, and the DHT scaffold was more resistant to the biodegradation of collagenase compared with the untreated sample.

Biocompatible Films of Collagen-Procyanidin for Wound Healing Applications

The study investigated the effect of polyphenols present in Cassia auriculata (CA) leaves in enhancing the stability of the collagen protein and the wound healing potential of collagen films. The crude ethanol extract of CA was analyzed for the presence of phytochemicals and purified by column chromatography using solvents with increasing polarity. The ethanol eluted active fractions (EEAF) that precipitated gelatin was characterized using HP-TLC, FTIR spectroscopy, ESI-FT-MS/MS, and ¹H NMR spectroscopy. The active compound was identified to be procyanidin B belonging to the proanthocyanidins group. The wound healing property of EEAF and collagen type I extracted from Clarias batrachus fish skin and the bovine tendon was assessed by in vitro scratch assay on L929 mice fibroblast cell lines. The EEAF-treated collagen coating enhanced in vitro wound closure in comparison with the uncoated dish. It was observed that EEAF treatment improved the physical strength of collagen films. The in vivo wound healing of the EEAF-treated collagen film was examined in male Wister rats and the wound site tissues were assessed. In vivo wound examination showed enhanced healing with EEAF incorporated collagen films. Comparatively, the EEAF-treated bovine tendon collagen films showed improved physical properties and better wound healing property than fish collagen films.

Collagen Cross-Linking Lignin Improves the Bonding Performance of Etch-and-Rinse Adhesives to Dentin

To evaluate the biomodification ability of lignin used as pre-treatment in human dentin before the application of an etch-and-rinse adhesive. Experimental hydroethanolic solutions with different cross-linking agents were used: 6.5% proanthocyanidins (PAC, from grape-seed extract); 2% cardanol (CARD, from cashew-nut shell liquid); lignin (LIG, from eucalyptus) at 1, 2 or 4% concentrations. The negative control (NC) was ethanol 50 v%. Extracted molars were prepared, and dentin microtensile bond strength (μTBS) was evaluated after 24 h water storage or 10,000 thermocycling aging. Further specimens were processed for SEM nanoleakage, micropermeability confocal microscopy evaluation and in situ degree of conversion (DC) through micro-Raman spectroscopy. Demineralized dentin sticks were submitted to a three-point bending test to evaluate the elastic modulus (E) before and after 1 min biomodification using the tested solutions. Moreover, it was also evaluated the mass changes and hydroxyproline (HYP) release after 4-weeks of water storage. Vibrational collagen crosslinking identification was evaluated through micro-Raman spectroscopy. The results were analyzed by analysis of variance (ANOVA) and Tukey’s test (α = 0.05). A significant reduction in μTBS was observed in groups NC (p < 0.001) and CARD (p = 0.026). LIG-4% showed no significant reduction in μTBS after aging (p = 0.022). Nanoleakage micrographs showed hybrid layer protection with all agents, but reduced micropermeability was attained only with lignin. Polymerization was negatively affected in the presence of all tested cross-linking agents, except LIG-1%. Lignin and cardanol increased the dentin E values, but only lignin reduced the mass loss in dentin specimens. Effective collagen crosslinking (1117 cm−1 and 1235 cm−1) was detected for all agents. HYP release was significantly lower with LIG-1% than NC (p < 0.001). Lignin was able to perform collagen cross-linking and prevent the degradation of unprotected dentin collagen, thereby improving the bonding performance of the composite restorations performed in this study.

Lose the stress: Viscoelastic materials for cell engineering

Biomaterials are widely used to study and control a variety of cell behaviors, including stem cell differentiation, organogenesis, and tumor invasion. While considerable attention has historically been paid to biomaterial elastic (storage) properties, it has recently become clear that viscous (loss) properties can also powerfully influence cell behavior. Here we review advances in viscoelastic materials for cell engineering. We begin by discussing collagen, an abundant naturally occurring biomaterial that derives its viscoelastic properties from its fibrillar architecture, which enables dissipation of applied stresses. We then turn to two other naturally occurring biomaterials that are more frequently modified for engineering applications, alginate and hyaluronic acid, whose viscoelastic properties may be tuned by modulating network composition and crosslinking. We also discuss the potential of exploiting engineered fibrous materials, particularly electrospun fiber-based materials, to control viscoelastic properties. Finally, we review mechanisms through which cells process viscous and viscoelastic cues as they move along and within these materials. The ability of viscoelastic materials to relax cell-imposed stresses can dramatically alter migration on two-dimensional surfaces and confinement-imposed barriers to engraftment and infiltration in three-dimensional scaffolds. STATEMENT OF SIGNIFICANCE: Most tissues and many biomaterials exhibit some viscous character, a property that is increasingly understood to influence cell behavior in profound ways. This review discusses the origin and significance of viscoelastic properties of common biomaterials, as well as how these cues are processed by cells to influence migration. A deeper understanding of the mechanisms of viscoelastic behavior in biomaterials and how cells interpret these inputs should aid the design and selection of biomaterials for specific applications.

Facile synthesis of food-grade and size-controlled nanocarriers based on self-assembly of procyanidins and phycocyanin

Nanocarriers provide the possibility to overcome the low solubility, poor stability, and low bioavailability of functional factors. However, most nanocarriers do not directly participate in the corresponding effects of functional factors, such as treating inflammatory bowel disease but lack the means to control their size accurately. Herein, nanocarriers were prepared by a one-pot method, using food-grade antioxidant procyanidins, vanillin, and phycocyanin as raw materials. The strategy involved the Mannich reaction among the phenolic hydroxyl groups of procyanidins, the aldehyde groups of vanillin, and the amino groups of phycocyanin. The obtained nanocarriers displayed controllable sizes ranging from 130 to 750 nm, showing good antioxidant capacity in scavenging free radicals and were biocompatible to Caco-2 cells and RAW 264.7 macrophages. Nanocarriers also exhibited an inhibitory effect on cell damage induced by acrylamide and H₂O₂. Moreover, the designed nanocarriers could be used for delivering active ingredients such as lutein, which showed a uniform spherical distribution, high encapsulation efficiency, and good biocompatibility. This work provides a facile synthesis method to prepare food-grade nanocarriers with functional properties, which can be potentially used in the delivery of functional factors.