Adsorption of Pb(II) ions from aqueous environment using eco-friendly chitosan schiff’s base@Fe 3 O 4 (CSB@Fe 3 O 4 ) as an adsorbent; kinetics, isotherm and thermodynamic studies

Fabrication of a novel polyvinylpyrrolidone/chitosan-Schiff base/Fe2O3 nanocomposite for efficient adsorption of Pb(II) and Hg(II) ions from aqueous solution

A novel magnetic polyvinylpyrrolidone/chitosan-Schiff base/Fe2O3 (PVP/CS-SB/Fe2O3) adsorbent was prepared by one-pot facile co-precipitation route for adsorption of Pb(II) and Hg(II) ions from aqueous solution. Fourier transform infrared-spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and Brunauer-Emmett-Teller (BET) were used to characterize the synthesized PVP/CS-SB/Fe2O3. The results predicted that the successfully synthesis of magnetic CSSB-PVP@Fe2O3. The effects of important factors such as pH solution, contact time, concentration of metal ions, adsorbent dose and co-existing ions on Pb(II) and Hg(II) adsorption were investigated. The maximum adsorption capacities of Pb(II) and Hg(II) ions at optimal conditions were 120 mg/g and 102.5 mg/g, respectively. The kinetic studies predicted that the adsorption followed the pseudo-second-order (PSO) model as chemisorption using the coordination of active sites of PVP/CS-SB/Fe2O3 with the metal ions and also n-π interactions. Reproducibility results predicted that the excellent regeneration ability after 6 adsorption cycles. According to the results of this work, the PVP/CS-SB/Fe2O3 nanocomposite is promising for Pb(II) and Hg(II) ions adsorption and can be potential as a simple, low-cost, high-efficient adsorbent for decontamination of other heavy metal ions from aqueous solution.

Mechanistic Evidence for Hg Removal from Wastewater by Biologically Produced Sulfur

A significant quantity of biologically produced sulfur (BPS) is generated as a by-product of chemical and biological desulfurization processes applied to landfill gas treatment. The beneficial upcycling of BPS has seen limited use in the environmental context. The effectiveness and underlying mechanism of BPS as an adsorbent for removing Hg2+ from both solution and wastewater were elucidated based on experiments encompassing surface characterization, adsorption isotherms, kinetics, and thermodynamics. The BPS exhibited remarkable efficacy in removing Hg2+ from solution, with the Langmuir model accurately describing the adsorption process and showing a maximum adsorption capacity of 244 mg g-1. Surface analysis through X-ray photoelectron spectroscopy and scanning electron microscopy revealed that Hg2+ complexed with sulfide on BPS surfaces, forming stable HgS. The adsorbed Hg was strongly retained in BPS, with less than 0.2% of the adsorbed Hg desorbed by strong acids. Adsorption kinetics followed the double-exponential first-order model, showing an initial rapid adsorption phase wherein 75% of the initial Hg2+ was removed within 5 min, followed by a slower adsorption rate. The thermodynamic parameters suggested that adsorption of Hg2+ by BPS was a spontaneous and endothermic process. Additionally, BPS effectively removed Hg2+ from wastewater, showing preference for Hg over other co-existing metals. These findings underscore the potential of BPS as an effective adsorbent for Hg2+ removal from wastewater.

Fabrication of two novel amino-functionalized and starch-coated CuFe2O4-modified magnetic biochar composites and their application in removing Pb2+ and Cd2+ from wastewater

Novel magnetic biochar composites (SFeCu@SBCO and FeCu@SBCO-NH2) were fabricated by modifying oxidized sawdust biochar (SBCO) with Fe/Cu loading, starch-coating/amination, characterized (FTIR, XRD, BET, SEM-EDS and XPS) and applied in capturing Pb2+ and Cd2+ from wastewater. Adsorption experiments revealed that SFeCu@SBCO and FeCu@SBCO-NH2 exhibited extraordinary adsorption performance toward Pb2+/Cd2+ with the maximum adsorption capacity reaching 184.26/173.35 mg g-1 and 201.43/190.81 mg g-1, respectively, which were >5 times higher than those of SBC. The great increase in adsorption capacity of the two adsorbents was ascribed to the introduction of CuFe2O4 and starch/amino groups. Pb2+ and Cd2+ adsorption was an endothermic reaction controlled by monolayer chemisorption. Complexation and electrostatic attraction were the two predominant mechanisms. Besides, ion exchange together with physical adsorption also occurred during the adsorption. Additionally, the both adsorbents displayed favorable stability and reusability as well as desirable anti-interfering ability to other metal cations. Taken together, the both adsorbents could be utilized as reusable magnetic adsorbents with promising prospect in the effective remediation of Pb2+/Cd2+ contaminated water. The study not only contributed to the better understanding of biochar modification strategy and the application of modified biochar in heavy metals pollutants removal, but also realized resource utilization of biomass waste.

High reusability and adsorption capacity of acid washed calcium alginate/chitosan composite hydrogel spheres in the removal of norfloxacin

Calcium alginate (CA) hydrogel spheres were widely used as adsorbents to remove organics, but their adsorption capacities and reusability to some antibiotics are unsatisfactory. In this study, calcium alginate/chitosan (CA/CTS) hydrogel spheres were prepared as precursors. Acid-washed CA/CTS (CA/CTS-M) hydrogel spheres (310.6 mg/g) behaved much better adsorption capacity of norfloxacin (NOR) than CA (69.5 mg/g) and CA/CTS (87.7 mg/g) hydrogel spheres. Astonishingly, after being reused for 15 cycles, CA/CTS-M has no loss of NOR adsorption capacity. In the original idea, acid wash was expected to remove the chitosan in CA/CTS hydrogel spheres for obtaining a larger specific surface area. Both scanning electron microscopy and Brunauer-Emmett-Teller test showed that acid wash can remove CTS from CA/CTS hydrogel spheres to increase the specific surface area. However, part of the chitosan remained in CA/CTS-M, having a role to enhance the structural stability of the material, because the acid-washed CA (about 2 mm) has a significantly smaller diameter than CA/CTS-M (about 3 mm). According to the influence of pH and density functional theory calculations, electrostatic attraction is the key driving force of NOR adsorption. Importantly, acid wash led to more negative-charged surface characterized by Zeta potential, which is the main reason of the significantly enhanced adsorption capacity of CA/CTS-M in removal of NOR. In short, CA/CTS-M hydrogel spheres are environment friendly and highly stable adsorbents with high adsorption capacity in the removal of NOR.

Synthesis and characterization of pendant N,N-dimethylaminobenzaldehyde-functionalized chitosan Schiff base composite (CS@MABA) as a new sorbent for removal of Pb(II) ions from aqueous media

In this work, new pendant N,N-dimethylaminobenzaldehyde-functionalized chitosan Schiff base composite (CS@MABA) was prepared from the simple and convenient condensation reaction between chitosan (CS) and N,N-dimethylaminobenzaldehyde (MABA) in ethanol-glacial acetic acid (1:1 v/v) and characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), differential scanning calorimetry (DSC) and scanning electron microscope (SEM). The as-prepared composite CS@MABA was applied for the removal of Pb(II) ions, due to the presence of imine, hydroxyl and phenyl groups, and the effects of important parameters such as solution pH, contact time and sorbent dosage on the removal percentage and adsorption capacity were investigated and discussed. The optimum conditions were found to be at pH 5, adsorbent dosage of 0.1 g, Pb(II) concentration of 50 mg/L and contact time of 60 min. The maximum Pb(II) removal percentage was found to be 94.28 % with the high adsorption capacity of 165 mg/g. The adsorption capacity of CS@MABA is remain 87 % after 5 adsorption-desorption cycles. The adsorption kinetic and isotherm studies indicated that the Pb(II) removal by CS@MABA follows a pseudo-first order and Langmuir models, respectively. Compared to similar compounds, the synthesized CS@MABA composite has shown a relatively high yield for removing Pb(II) ions. According to these results, the CS@MABA suggested for the sorption of other heavy metals.

Synthesis and Characterization of Biodegradable Poly(vinyl alcohol)-Chitosan/Cellulose Hydrogel Beads for Efficient Removal of Pb(II), Cd(II), Zn(II), and Co(II) from Water

Globally, water contamination by heavy metals is a serious problem that affects the environment and human health. Adsorption is the most efficient way of water treatment for eliminating heavy metals. Various hydrogels have been prepared and used as adsorbents to remove heavy metals. By taking advantage of poly(vinyl alcohol) (PVA), chitosan (CS), cellulose (CE), and the process for physical crosslinking, we propose a simple method to prepare a PVA-CS/CE composite hydrogel adsorbent for the removal of Pb(II), Cd(II), Zn(II) and Co(II) from water. Structural analyses of the adsorbent were examined by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy-energy dispersive X-ray (SEM-EDX) analysis, and X-ray diffraction (XRD). PVA-CS/CE hydrogel beads had a good spherical shape together with a robust structure and suitable functional groups for the adsorption of heavy metals. The effects of adsorption parameters such as pH, contact time, adsorbent dose, initial concentration of metal ions, and temperature on the adsorption capacity of PVA-CS/CE adsorbent were studied. The adsorption characteristics of PVA-CS/CE for heavy metals may be completely explained by pseudo-second-order adsorption and the Langmuir adsorption model. The removal efficiency of PVA-CS/CE adsorbent for Pb(II), Cd(II), Zn(II), and Co(II) was 99, 95, 92, and 84%, respectively, within 60 min. The heavy metal's hydrated ionic radius may be crucial in determining the adsorption preference. After five consecutive adsorption-desorption cycles, the removal efficiency remained over 80%. As a result, the outstanding adsorption-desorption properties of PVA-CS/CE can potentially be extended to industrial wastewater for heavy metal ion removal.

Facile Strategy for Fabricating an Organosilica-Modified Fe3O4 (OS/Fe3O4) Hetero-nanocore and OS/Fe3O4@SiO2 Core-Shell Structure for Wastewater Treatment with Promising Recyclable Efficiency

The development of a sustainable process for heavy metal ion remediation has become a point of interest in various fields of research, including wastewater treatment, industrial development, and health and environmental safety. In the present study, a promising sustainable adsorbent was fabricated through continuous controlled adsorption/desorption processes for heavy metal uptake. The fabrication strategy is based on a simple modification of Fe₃O₄ magnetic nanoparticles with organosilica in a one-pot solvothermal process, carried out in order to insert the organosilica moieties into the Fe₃O₄ nanocore during their formation. The developed organosilica-modified Fe₃O₄ hetero-nanocores had hydrophilic citrate moieties, together with hydrophobic organosilica ones, on their surfaces, which facilitated the further surface coating procedures. To prevent the formed nanoparticles from leaching into the acidic medium, a dense silica layer was coated on the fabricated organosilica/Fe₃O₄ (OS/Fe₃O₄). In addition, the prepared OS/Fe₃O₄@SiO₂ was utilized for the adsorption of cobalt(II), lead(II), and manganese(II) from the solutions. The data for the adsorption processes of cobalt(II), lead(II), and manganese(II) on OS/(Fe₃O₄)@SiO₂ were found to follow the pseudo-second-order kinetic model, indicating the fast uptake of heavy metals. The Freundlich isotherm was found to be more suitable for describing the uptake of heavy metals by OS/Fe₃O₄@SiO₂ nanoparticles. The negative values of the ΔG° showed a spontaneous adsorption process of a physical nature. The super-regeneration and recycling capacities of the OS/Fe₃O₄@SiO₂ were achieved, comparing the results to those of previous adsorbents, with a recyclable efficiency of 91% up to the seventh cycle, which is promising for environmental sustainability.

Application of new chitosan 2,4-dihydroxyacetophenone Schiff base @SrFe12O19 nanocomposite for remove of Pb(II) ion from aqueous solution

A new chitosan 2,4-dihydroxyacetophenone Schiff base @SrFe₁₂O₁₉ (Cs-SB@SrFe₁₂O₁₉) nanocomposite was successfully prepared by one-pot reaction and fully characterized for its functional groups, morphology, elemental analysis and thermal behavior by FT-IR, XRD, VSM, DSC, TGA, zeta potential, FE-SEM and EDS techniques. The VSM result showed that Cs-SB@SrFe₁₂O₁₉ has M_s of 11.81 emu/g and H_c of 5488 Oe, known as hard magnetic material. Finally, the as-prepared sample utilized as a new sorbent for the removal of Pb(II) ions from aqueous solution by using batch adsorption experiments. The adsorption of Pb(II) was carried out at different pH, contact time and initial dose of Cs-SB@SrFe₁₂O₁₉. The maximum adsorption capacity was found to be 132 mg/g (99 %) at pH 5 and the contact time of 120 min. Finally, the kinetic studies reveals that the adsorption process of Cs-SB@SrFe₁₂O₁₉ followed by the pseudo second order kinetics model. Also, the sample showed excellent recyclable efficiency up to 5 cycles.

Synthesis of powdered and beaded chitosan materials modified with ZnO for removing lead (II) ions

Lead contamination in wastewater may affect aquatic organisms, the environment, and human consumption because it is a highly toxic metal that caused human health effects. Thus, it is recommended to remove lead before releasing it into the environment. Powdered and beaded chitosan materials modified with ZnO were synthesized and investigated by various characterized techniques. Lead removal efficiencies of chitosan materials were studied by batch experiments, adsorption isotherms, and kinetics. Chitosan powder (CP), chitosan beads (CB), chitosan beads mixed ZnO (CZB), and chitosan beads coated ZnO (ZCB) were synthesized. CP represented a semi-crystalline structure while CB was an amorphous structure. CZB and ZCB were semi-crystalline structures with ZnO peaks. CP was a scaly-sheet and coarse surface while CB, CZB, and ZCB were sphere shapes with scaly-sheet surfaces. C, O, and N were the main chemical elements in chitosan materials, and Zn was detected in CZB and ZCB. O-H, N-H, and C-O were the main functional groups of chitosan materials. All chitosan materials had high lead removal efficiencies of more than 92%, and Freundlich and pseudo-second-order kinetic models well explained their adsorption patterns and mechanisms. Therefore, both adding metal oxide and changing material form are recommended for improving material efficiency, and ZCB was a good offer for further industrial applications.

Magnetic sporopollenin supported polyaniline developed for removal of lead ions from wastewater: Kinetic, isotherm and thermodynamic studies

This study evaluated the synthesis of novel binary functionaladsorbent based on sporopollenin, magnetic nanoparticles, and polyaniline to produce MSP-PANI. The MSP-PANI was applied to enhance uptake of lead ions (Pb²⁺) from wastewater samples. The functionalities, surface morphology, magnetic properties, and elemental composition of the newly synthesized nanocomposite were investigated using Fourier transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FE-SEM), vibration sample magnetometer (VSM), and energy-dispersive X-ray spectroscopy (EDX), respectively. The experimental condition for the adsorption process was MSP/PANI ratio 1:1, pH ∼6, adsorbent dosage 40 mg, and contact time 90 min at room temperature. Under the proposed condition, lead ions removal were obtained as 83%, 88% and 95% for MSPE, PANI, and MSP/PANI, respectively. Based on the experimental and predicted data, the adsorption was corresponded to the psudo-second-order (R² = 0.999) kinetics model, and the adsorption equilibrium corresponded to the Langmuir model (R² = 0.996). Langmuir isotherm showed the maximum adsorption capacity of MSP-PANI for lead ions was 163 mg/g and followed the monolayer pattern. Hence, thermodynamic model under Van't Hoff equation suggested that the adsorption mechanism was physio-sorption with endothermic nature. Therefore, this research can help the researchers to use magnetic nanoparticles for lead removal in highly polluted areas.

Efficient removal of Pb(II) using modified chitosan Schiff base@Fe/NiFe

A novel modified chitosan Schiff base@Fe₂O₃-NiFe₂O₄ (CsSB@Fe/NiFe) was prepared and characterized using FT-IR, XRD, SEM, EDX, TGA, DSC and VSM. FT-IR and XRD results confirm that the nanoparticles of Fe/NiFe distributed throughout the surface of CS-OH and successfully prepared CsSB@Fe/NiFe. SEM image shows that the Fe/NiFe nanoparticles were assembled in the surface and inside of CS-OH. Coercivity (H_c) of CsSB@Fe/NiFe is ≈ 110 Oe, indicated that it was kind of soft-magnetic materials with saturation magnetization (M_s) of 6.45 emu/g. In addition, CsSB@Fe/NiFe was further explored as an new sorbent for the removal of Pb(II) ion from aqueous solution and the influence of various important parameters such as solution pH, contact time, dosage of adsorbent and initial Pb(II) concentration were studied and optimized. Optimum conditions for Pb(II) removal were found to be pH 5, adsorbent dosage 0.05 g, initial Pb(II) concentration of 75 ppm and contact time of 120 min. The maximum Pb(II) removal percentage was found to be 97%. Also, CsSB@Fe/NiFe shows about 88% Pb(II) removal after five adsorption-desorption cycles. The results suggested that the sorption of Pb(II) onto CsSB@Fe/NiFe was feasible and spontaneous.

Adsorptive removal of Pb(II) ions onto surface modified adsorbents derived from Cassia fistula seeds: Optimization and modelling study

Cassia fistula seeds has been utilized for the abstraction of Pb(II) ions from the aqueous environment. Raw Cassia fistula seeds (RCF) and three different surface modified (physically treated - PMCF and chemically treated - HMCF and SMCF) adsorbent material were taken for investigation. The adsorption properties of these materials and their contact amongst the Pb(II) ion and sorbent materials were characterized by FTIR and SEM analysis. The parameters influencing the adsorption capacity of varied adsorbents were evaluated: maximum solution pH for Pb(II) is 5.0; interactive time is 30 min; dosage is 8.0 g/L for RCF, 4.0 g/L for HMCF, 2.5 g/L for PMCF and 1.0 g/L for SMCF. The modelling study reveals that Freundlich isotherm and Pseudo first order kinetics fits well and the utmost adsorption measurements for the varied adsorbents were found to be 13.22, 28.28, 48.66 and 129.3 mg/g, respectively.

Assessment of a novel aminated magnetic adsorbent with excellent adsorption capacity for dyes and drugs

Dyes and drugs with high toxicity and low biodegradability pose risk to human health and ecological security, and should be purified efficiently from effluents before discharge. Traditional adsorbents are limited by the insufficient active adsorption sites and low stability. In this study, a novel aminated magnetic adsorbent (MCTs) was fabricated via two cross-linking steps using chitosan and triethylenetetramine to fill the gaps between current adsorbent and performance requirements. The morphological and physicochemical characteristics of the as-prepared MCTs were determined and identified with the aid of several characterization techniques. The adsorption performance of dyes and drugs was also investigated and represented by their adsorption capacities. In particular, the adsorption capacities of Congo Red, Chicago Sky Blue, Reactive Brilliant Red, and Ibuprofen were 583.11, 465.01, 403.12, and 291.71 mg/g, respectively. They also remained at around 80% after four reuse cycles. MCTs were adsorbed via a monolayer spontaneous chemical reaction, and hydrogen bonding and electrostatic interaction were the dominant adsorption mechanisms. These results demonstrated that the preparation of MCTs via two cross-linking steps enhanced the adsorbents' adsorption capacity, reusability, and stability. They provided a new perspective for the preparation of high-efficient adsorbents and the purification of dye- and drug-polluted wastewater.

Removal of lead ions by two FeMn oxide substrate adsorbents

Lead pollution has become a global concern due to its ubiquity and persistence. This study describes two FeMn oxide substrate adsorbents, namely, FeMn binary oxides (FMBO) and mesoporous FeMn binary oxide (MFMBO) covered with tannic acid film (FMBO@TA-Fe³⁺ and MFMBO@TA-Fe³⁺), for the treatment of Pb²⁺ in water. The characterization results showed that TA was successfully coated onto the surfaces of FMBO and MFMBO. The maximum capacities of Pb²⁺ on FMBO@TA-Fe³⁺ and MFMBO@TA-Fe³⁺ were 322.08 and 357.14 mg g^-1, respectively, which were twice those of FMBO and MFMBO. The adsorption of Pb²⁺ on the adsorbents was a spontaneous, endothermic process with increasing disorder through thermodynamics studies. An overall mechanism was proposed for Pb²⁺ adsorption, the improved adsorption performance of FMBO@TA-Fe³⁺ and MFMBO@TA-Fe³⁺ is ascribed to the mesoporous characteristics and the introduction of hydroxyl groups. Further investigation indicated the adsorption of Pb²⁺ could be attributed to electrostatic interactions on FMBO@TA-Fe³⁺ and MFMBO@TA-Fe³⁺, and cation exchange existed through the formation of these internal surface complexes. The Pb²⁺-loaded adsorbents could be effectively desorbed in a dilute hydrochloric acid solution, promoting recycling and reuse of the regenerated adsorbents. These results warrant the promising application of FMBO@TA-Fe³⁺ and MFMBO@TA-Fe³⁺ for the removal of Pb²⁺, and this work first proposed TA film-modified FMBO and MFMBO to improve its adsorption capacity in the application of environmental remediation.

Development of a polymeric nanocomposite as a high performance adsorbent for Pb(II) removal from water medium: Equilibrium, kinetic and antimicrobial activity

In the present study, starch based ZnO nancomposite (CSt-ZnO) was synthesized for the efficient removal of Pb(II) ions from aqueous medium. The structure and morphology of CSt-ZnO nancomposite was characterized using SEM, FTIR, TGA, BET, XPS and zeta potential measurements. The effect of contact time, pH, temperature and initial concentration of Pb(II) on the adsorption was studied. The optimum parameters for maximum Pb(II) removal were time-120 min; pH-6; temperature-318 K and C_o-20 ppm. The maximum Langmuir adsorption capacity of CSt-ZnO nancomposite was 256.4 mg/g at 298 K. With increasing the temperature from 298 K to 318 K, the maximum adsorption quantity (q_m) was improved from 256.4 to 476 mg/g which showed the endothermic nature of Pb(II) adsorption on CSt-ZnO nanocomposite. The sorption isotherm and kinetics model fitting studies, confirmed that data fit well to Freundlich isotherm and pseudo-first-order kinetics models, respectively. Thermodynamic studies inferred a spontaneous and endothermic nature of adsorption. Moreover, the adsorption capacity was 68% even after four adsorption-desorption cycles which revealed the reusable performance of CSt-ZnO was well. The antimicrobial activity of CSt-ZnO nanocomposite was also examined against S. aureus and E. coli.

Insecticidal activity of some synthesized 1,3,4-oxadiazole derivatives grafted on chitosan and polymethylmethacrylate against the cotton leafworm Spodoptera littoralis

To combat insect pests and vectors that are responsible for high losses in food and lives, insecticide discovery is of top priority. This study aimed to synthesize, characterize and investigate the insecticidal activity of 1,3,4-oxadiazole derivatives grafted on chitosan (CS) and modified polymethyl methacrylate (PMMA). 5-(pyridin-3-yl)-1,3,4-oxadiazole-2-thiol and 5-(pyridin-4-yl)-1,3,4-oxadiazole-2-thiol were respectively reacted with ethylchloroacetate and methyl-2-choloroacetoacetate. The resulted esters were grafted with CS and modified-PMMA. The products were characterized using FT-IR, ¹H NMR, TGA, and XRD techniques. Four CS grafted ones were able to show good insecticidal activity against the cotton leafworm Spodoptera littoralis. Furthermore, the safety of these compounds was tested using MTT assay on a human cell line (WI-38). The results indicated that compounds 2a, 2b, 6a, and 6d are considered insecticide candidates to S. littoralis fourth-instar larvae. Cytotoxicity of 2b and 6d indicated that they are the least toxic to humans. It is concluded that both compounds may represent promising insecticide candidates.

Preparation of Sodium Lignosulfonate/Chitosan Adsorbent and Application of Pb2+ Treatment in Water

Industrial wastewater has brought huge disasters to water resources and soil and has seriously affected the growth of animals and plants. There is an urgent need for a green and efficient adsorbent to solve the problem of water pollution. Sodium lignosulfonate and chitosan undergo free radical polymerization to form a lignin/chitosan adsorbent, which is used to treat Pb2+ in water pollution. An orthogonal experiment was used to optimize the content of sodium lignosulfonate, chitosan, cross-linking agent and initiator to obtain the adsorbent with the best adsorption performance. The adsorbents were characterized by Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), thermal analysis and zeta potentiometry. The influence of different conditions on the adsorption of heavy metal ions by lignosulfonate/chitosan adsorbent was explored, and a kinetic and isotherm model was established. The results showed that the adsorption capacity of Pb2+ was 345 mg g−1 when the adsorbent was 0.01 g, the concentration of heavy metal ions was 100 mg L−1 and pH was 7. The adsorption process of lignosulfonate/chitosan is a kind of spontaneous adsorption mode, which is mainly composed of electrostatic adsorption and chemical adsorption.

Simultaneously enhanced removal and stepwise recovery of atrazine and Pb(II) from water using β-cyclodextrin functionalized cellulose: Characterization, adsorptive performance and mechanism exploration

Heavy metals and pesticides often coexist in contaminated water, while their potential competition behaviors make the adsorptive removal more challenging. Thus, decorating an adsorbent with independent functional sites could be a promising alternative to radically prevent the competitive process for improving the adsorption performance. Herein, β-cyclodextrin functionalized rice husk-based cellulose (β-CD@RH-C) was designed and applied for synchronous removal of atrazine and Pb(II). The characterization results supported the successful grafting of β-cyclodextrin onto the cellulose. The β-CD@RH-C presented a pH-dependent adsorption performance for Pb(II) with a theoretical monolayer adsorption capacity of 283.00 mg/g, while was mostly unrelated to pH for atrazine adsorption with a heterogeneous uptake of 162.21 mg/g in the mono-component system. Most importantly, the β-CD@RH-C could efficiently achieve simultaneous removal of atrazine and Pb(II) via avoiding their competitive behaviors, which was due to the different adsorption mechanisms for atrazine (i.e. host-guest interaction) and Pb(II) (i.e. complexation and electrostatic interaction). Moreover, the adsorbed atrazine and Pb(II) could be sequentially desorbed with slight decrease in the adsorption performance of β-CD@RH-C even after four cycles in the atrazine-Pb(II) multi-component system. All these results suggested β-CD@RH-C to be a tailored adsorbent with high-performance elimination of co-existing heavy metals and organic pollutants in water.

Preparation of novel chitosan polymeric nanocomposite as an efficient material for the removal of Acid Blue 25 from aqueous environment

A novel, sustainable chitosan polymeric nanocomposite (CS-PVA@CuO) was synthesized and subjected to the removal of acid blue 25 (AB25) from the aqueous environment. The influence of different variables such as p^H, contact time, initial dye concentration, temperature, and adsorption kinetics has been examined in the batch adsorption process. The CS-PVA@CuO composite was systematically characterized by XRD, FTIR, SEM, and EDX analysis. The pseudo-first order (PFO), pseudo-second order (PSO), and intra-particle diffusion kinetics equations were used to examine the kinetic data of the adsorption process. The adsorption kinetics confirms that the PSO model was a more exact fit. Thermodynamics study typically revealed that the uptake of AB25 by the adsorbent is spontaneous and endothermic in nature. Remarkably, the results reveal the highest adsorption capacity of the CS-PVA@CuO was 171.4 mg/g at 313 K. To be specific, CS-PVA@CuO polymer nanocomposite can be effectively used as a suitable adsorbent material for the potential elimination of anionic AB25 dye from the aqueous solutions.

Removal of atrazine from aqueous solutions onto a magnetite/chitosan/activated carbon composite in a fixed-bed column system: optimization using response surface methodology

In this study, a magnetite/chitosan/activated carbon (MCHAC) composite is proposed as an efficient adsorbent for the removal of atrazine from aqueous solutions. The prepared composite was characterized using Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) methods. Response surface methodology (RSM) coupled with composite central design (CCD) were used to optimize the effects of the four independent variables, pH, initial concentration of atrazine (C 0), bed depth (H), and flow rate (Q), which influence the adsorption process. The experimental results modeled using response surface methodology (RSM) coupled with central composite design (CCD) (RSM-CCD) indicated a quadratic relationship with p < 0.0001 for adsorption capacity at saturation (q s) and fraction of bed utilization (FBU). The results of the experiments performed under the optimized conditions, pH = 5.07, C 0 = 137.86 mg L-1, H = 2.99 cm and Q = 1.038 mL min-1, showed a q s value of 62.32 mg g-1 and FBU of 72.26%, with a deviation value of less than 0.05 from the predicted q s and FBU values. The obtained breakthrough curves were fitted with four mathematical models, Thomas, Bohart-Adams, Yan and Yoon-Nelson, in order to determine the limiting step of the mass transfer of the atrazine adsorption onto the composite. A desorption study of the composite revealed the high reuse potential for MCHAC, thus, the prepared material could be used as a low-cost and efficient adsorbent for the decontamination of polluted wastewater.

Use of nano-/micro-magnetite for abatement of cadmium and lead contamination

Structural variations of a mineral dictate its adsorption capacity which affects the mobility and toxicity of contaminants in natural and engineered systems. Present batch study evaluates the adsorption of lead (Pb) and cadmium (Cd) onto three magnetites having nanometric (M1-30 nm and M2-60 nm) and micrometric particle sizes (M3-1.5 μm). Obtained data revealed that particle size of tested magnetites strongly affected the extent and kinetics of metal adsorption and desorption. Observed order of adsorption efficiency was M1 > M2 > M3 with optimum monolayer adsorption of 408.14, 331.40, 178.47 mg/g (for Pb) and 228.05, 170.86, 83.49 mg/g (for Cd), respectively. Adsorption data were well fitted to the Freundlich (R² = 0.99), Langmuir (R² = 0.99) and pseudo-first order models (R² = 0.98). Electrostatic attraction and surface precipitation interaction via external mass transfer between bulk liquid-solid interfaces were the potential adsorption pathways. Pb showed higher affinity than Cd in multi-metal system. Desorption efficiency was higher in acidic environment (92%) than in distilled water (44%). Moreover, regenerated magnetite samples retained good adsorption capacity for six cycles. As soils are characterized by large variability of iron minerals, these findings have important implications regarding the transport and immobilization of contaminants particularly in the management of contaminated soils.

Preparation of chitosan based magnetic nanocomposite for tetracycline adsorption: Kinetic and thermodynamic studies

In the present study, the magnetic nanocomposite is fabricated using chitosan, thiobarbituric acid, malondialdehyde and Fe₃O₄ nanoparticles (CTM@Fe₃O₄). The fabricated nanocomposite (CTM@Fe₃O₄) is characterized using FTIR, TGA, BET, XRD, Raman, XPS, FESEM, and HRTEM techniques. The results of BET analysis confirmed that the nanocomposite has a mesoporous structure with high surface area of 376 m² g^-1 and high pore volume 0.3828 cm³ g^-1. The adsorption of tetracycline (TC) onto CTM@Fe₃O₄ adsorbent is carried out using batch technique by changing several factors such as pH, concentration, contact time, and temperature. Langmuir and pseudo-second-order nonlinear models were found to be the best-fit models to predict isotherms and kinetics of adsorption, respectively. The highest adsorption capacity of 215.31mg/g was achieved at the optimum conditions of 0.05g adsorbent dosage, 60mg/L TC concentration. Overall, results demonstrated that CTM@Fe₃O₄ nanocomposite was an excellent adsorbent material with superparamagnetic properties, which allowed the separation as well as recovery of the adsorbent from aqueous solution using external magnet for effective industrial applications.

New effective 3-aminopropyltrimethoxysilane functionalized magnetic sporopollenin-based silica coated graphene oxide adsorbent for removal of Pb(II) from aqueous environment

A new effective adsorbent, 3-aminopropyltrimethoxysilane functionalized magnetic sporopollenin (MSp@SiO₂NH₂) based silica-coated graphene oxide (GO), (GO@SiO₂-MSp@SiO₂NH₂) was successfully synthesized and applied for the first time in the removal of hazardous Pb(II) ions from aqueous solution. The properties of the composite were characterized using Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDX) and vibrating-sample magnetometery (VSM). Evaluation of GO@SiO₂-MSp@SiO₂NH₂ adsorption performance at optimum conditions revealed that the adsorbent has a maximum adsorption capacity of 323.5 mg/g for Pb(II) using 50-200 mg/L initial Pb(II) ions concentrations. Initial and final concentrations of Pb(II) ions in aqueous solution were analyzed using graphite furnace atomic absorption spectroscopy (GF-ASS). The adsorption behavior of Pb(II) ions onto GO@SiO₂-MSp@SiO₂NH₂ was studied using Langmuir, Freundlich and Temkin isotherms models. The values of coefficient of determination showed that the adsorption best fitted the Langmuir model (R² = 0.9994). Kinetic studies suggested that the adsorption of Pb(II) ion followed a pseudo-second-order rate model (R² = 1.00) and thermodynamic studies revealed that the adsorption process is endothermic and spontaneous. The effect of co-existing ions on Pb(II) ion adsorption were also studied and found to have considerable effects only at higher matrix concentration. The adsorbent can be reused up to ten times and retain its good adsorption capacity. In addition, GO@SiO₂-MSp@SiO₂NH₂ showed great potential for Pb(II)removal from industrial wastewater samples.

Chitosan/ nanofibrillated cellulose aerogel with highly oriented microchannel structure for rapid removal of Pb (II) ions from aqueous solution

Among the heavy metal ions, Pb (II) can cause serious diseases in the nervous and cardiovascular systems even at an ultralow concentration. Nowadays, various materials with high adsorption capacity have been developed for heavy metal ions adsorption. However, most of them have a low adsorption rate and may take a long time to achieve adsorption equilibrium. In this work, chitosan (CS)/ nanofibrillated cellulose (NFC) aerogel with oriented microchannel structure was developed via a directional freeze-drying approach. The structure of the CS/NFC aerogel was characterized and its adsorption performance for Pb (II) was also investigated. The results reveal that the maximum adsorption capacity for Pb (II) is 252.6 mg g^-1, much higher than most chitosan-based adsorbents reported in the literature. More impressively, the developed aerogel takes only 5 min to achieve 85% of equilibrium adsorption capacity for Pb (II) due to its highly oriented microchannel structure. Furthermore, the aerogel maintains a high removal efficiency (>85%) after 5 adsorption-desorption cycles. The obtained results demonstrate that the as-prepared CS/NFC aerogel can be used as an effective adsorbent for Pb (II) removal from aqueous solution.

Uptake of Pb(II) onto nanochitosan/sodium alginate hybrid beads: Mechanism and kinetics study

Nanochitosan/sodium alginate (NCS/SA) beads were prepared using nanochitosan and alginate as a high-performance absorbent for Pb(II) removal from aqueous solution. The morphology, structure, thermal stability, surface area, and elements present in the NCS/SA beads before and after adsorption were characterized using instrumental techniques like SEM, FTIR, TGA, BET, and EDX analysis, respectively. Various adsorption parameters were studied. The results indicated that the equilibrium adsorption data were fitted to Langmuir isotherms and the maximum Langmuir monolayer capacity of Pb(II) was 178.57 mg/g at 45°C. The adsorption process was in good agreement with pseudo-first-order kinetic model. Mechanism studies showed that electrostatic interaction and ion exchange were the major mechanisms for lead (II) removal by the NCS/SA beads. The results of this study indicate that NCS/SA beads could be used as an effective adsorbent for the elimination of lead (II) present in aqueous solution. PRACTITIONER POINTS: Nanochitosan/sodium alginate beads were synthesized using Ca²⁺ as a crosslinking agent. NCS/SA beads were used to remove Pb(II) for the first time and working parameters were optimized. Adsorption monolayer capacity of NCS/SA adsorbent towards Pb (II) was found to be 178.57 mg/g.

A review on applications of chitosan-based Schiff bases

Biopolymers have become very attractive as they are degradable, biocompatible, non-toxic and renewable. Due to the intrinsic reactive amino groups, chitosan is vibrant in the midst of other biopolymers. Using the versatility of these amino groups, various structural modifications have been accomplished on chitosan through certain chemical reactions. Chemical modification of chitosan via imine functionalization (RR'CNR″; R: alkyl/aryl, R': H/alkyl/aryl and R″: chitosan ring) is significant as it recommends the resultant chitosan-based Schiff bases (CSBs) for the important applications in the fields like biology, catalysis, sensors, water treatment, etc. CSBs are usually synthesized by the Schiff condensation reaction between chitosan's amino groups and carbonyl compounds with the removal of water molecules. In this review, we first introduce the available synthetic approaches for the preparation of CSBs. Then, we discuss the biological applications of CSBs including antimicrobial activity, anticancer activity, drug carrier ability, antioxidant activity and tissue engineering capacity. Successively, the applications of CSBs in other fields such as catalysis, adsorption and sensors are demonstrated.

A Hydrothermal Synthesis of Fe3O4@C Hybrid Nanoparticle and Magnetic Adsorptive Performance to Remove Heavy Metal Ions in Aqueous Solution

Advanced core-shelled material with a high specific area has been considered as an effective material to remove heavy metal from aqueous solutions. A core-shelled Fe3O4@C hybrid nanoparticle aggregates with environmental-friendly channel in the study. Moreover, the higher exposure of adsorption sites can be achieved for the special configuration that higher Brunauer-Emmet-Teller (BET) surface area reaches up to 238.18 m2 g-1. Thus, a more efficiently heavy metal ion removal is obtained, Pb (II), Cd (II), Cu (II), and Cr (VI) up to 100, 99.2, 96.6, and 94.8%, respectively. In addition, the products are easy to be separated from the aqueous solutions after adsorption, due to the relative large submicrometer size and the enhanced external magnetic fields introduced by the iron-based cores. We provide an ideal mode to remove heavy metal ions using core-shelled Fe3O4@C under the water treatment condition. A new approach is clarified that core-shell nano/micro-functional materials can be synthesized well on large scales which are used in many fields such as environmental remediation, catalyst, and energy.