Intelligent superabsorbents based on a xanthan gum/poly (acrylic acid) semi-interpenetrating polymer network for application in drug delivery systems

Syzgium cumini seed/poly vinyl alcohol based water resistant biodegradable nano-cellulose composite reinforced with zinc oxide and silver oxide nanoparticles for improved mechanical properties

The current work explored a comparative study of biodegradable jamun seed/polyvinyl alcohol (JS) nanocomposites reinforced with varying concentrations of ZnO and Ag2O nano-fillers. The effect of spherical shaped ZnO and Ag2O nanoparticles (NPs) on the on structure, morphology, swelling and solubility, crystallinity and mechanical properties together with biodegradation performance of the composite films was fully studied. SEM results showed uniform distribution of ZnO and Ag2O nanofillers into the JS matrix and dense or compact nanocomposite films were formed. JS-ZnO and JS-Ag2O nanocomposites with 0.5 wt% ZnO and Ag2O content showed maximum crystallinity i.e. 11.3 and 9.58 %, respectively, as determined by XRD. When compared to the virgin JS film (8.41 MPa), the resultant JS-ZnO-0.5 and JS-Ag2O-0.5 nanocomposites showed significantly enhanced tensile strength (35.7 MPa, 29.2 MPa), elongation at break (15.42 %, 14.62 %) and Young's modulus (141 MPa, 126 MPa), respectively. Also, reduced swelling (120.4 % and 116.1 %) and solubility ratio (17.45 % and 18.42 %) was observed for JS-ZnO-0.5 and JS-Ag2O-0.5 nanocomposites, respectively. Biodegradation results showed that maximum degradation (88 %) was achieved for the JS film within 180 days of soil burial whereas JS-ZnO-0.1 and JS-Ag2O-0.1 nanocomposites showed 78 % and 72 % degradation within 180 days, respectively.

Absorbable and biodegradable enzyme-crosslinked gelatin/alginate semi-IPN hydrogel wound dressings containing curcumin

Effective wound management presents a substantial financial and time-related obstacle for healthcare institutions. Enhancing healthcare involves implementing innovative wound treatment methods to minimize healing time and expenses. This study is centered on the development of a non-toxic wound dressing using only two natural polymers and an enzyme. By adding 10 % wt microbial transglutaminase, the mechanical properties of the dressing were improved. This formulation increased the swelling rate by 70 %, deswelling rate by 15 %, conversion rate by 9 %, and networking rate by 20 %. Additionally, the non-toxic dressing showed a cell viability rate of 106 %. In drug delivery tests, explosive release behavior was observed, which is advantageous for open wounds. Cell staining experiments were also carried out to evaluate wound behavior in terms of collagen formation, granulation, and inflammation. The results suggest that the optimized hydrogel has great potential as a wound dressing. Its excellent absorption, antioxidant, and biocompatibility characteristics enhance tissue granulation rate and reduce wound treatment time by half compared to conventional methods, while also minimizing scarring risk. This innovative treatment, which eliminates the need for frequent changes, is beneficial for both secondary intentions and severe open wounds requiring bottom-up healing.

Development of novel iron(III) crosslinked bioinks comprising carboxymethyl cellulose, xanthan gum, and hyaluronic acid for soft tissue engineering applications

The advent of three-dimensional (3D) bioprinting offers a feasible approach to construct complex structures for soft tissue regeneration. Carboxymethyl cellulose (CMC) has been emerging as a very promising biomaterial for 3D bioprinting. However, due to the inability to maintain the post-printed stability, CMC needs to be physically blended and/or chemically crosslinked with other polymers. In this context, this study presents the combination of CMC with xanthan gum (XG) and hyaluronic acid (HA) to formulate a multicomponent bioink, leveraging the printability of CMC and XG, as well as the cellular support properties of HA. The ionic crosslinking of printed constructs with iron(III) via the metal-ion coordination between ferric cations and carboxylate groups of the three polymers was introduced to induce improved mechanical strength and long-term stability. Moreover, immortalized human epidermal keratinocytes (HaCaT) and human foreskin fibroblasts (HFF) encapsulated within iron-crosslinked printed hydrogels exhibited excellent cell viability (more than 95%) and preserved morphology. Overall, the presented study highlights that the combination of these three biopolymers and the ionic crosslinking with ferric ions is a valuable strategy to be considered for the development of new and advanced hydrogel-based bioinks for soft tissue engineering applications.

Research progresses on carboxymethyl xanthan gum: Review of synthesis, physicochemical properties, rheological characterization and applications in drug delivery

Xanthan gum is a nonionic polysaccharide widely explored in biomedical, nutraceutical, and pharmaceutical fields. XG suffers from several drawbacks like poor dissolution, lower bioavailability and an inability to form hydrogels. The carboxymethyl derivative of XG, CMX, has better solubility, dissolution, and bioavailability characteristics. Moreover, due to its anionic character, it forms water insoluble hydrogels upon crosslinking with metal cations. CMX hydrogels are used to prepare matrix tablets, microparticles, beads, and films. CMX hydrogels has been used in drug delivery and tissue engineering fields. CMX hydrogels are used for sustained gastrointestinal, colon targeted, and transdermal delivery of drugs. CMX nanoparticles have been used for targeted delivery of anticancer drugs to tumor cells. CMX hydrogels have already made significant strides in drug delivery and tissue engineering fields. Further understanding of the physicochemical properties and rheological characteristics of CMX would enable researchers to explore newer applications of CMX. This review article thus aims to discuss the synthesis, physicochemical properties, and rheological characteristics of CMX. The article also gives critical insights on the versatility of CMX as a drug delivery carrier and presents prospective trends on applications of CMX.

Nanoparticles of Thiolated Xanthan Gum for the Oral Delivery of Miconazole Nitrate: In Vitro and In Vivo Evaluation

The objective of this research was to develop a mucoadhesive delivery system that improves permeation for the administration of poorly absorbed oral medications. Thiolation of xanthan gum (XGM) was carried out by esterification with mercaptobutyric acid. Fourier-transformed infrared spectroscopy was used to confirm thiol-derivatization. Using Ellman's technique, it was revealed that the xanthan-mercaptobutyric acid conjugate had 4.7 mM of thiol groups in 2 mg/mL of polymeric solution. Using mucosa of sheep intestine, the mucoadhesive properties of XGM and thiolated xanthan gum (TXGM) nanoparticles were investigated and we found that TXGM had a longer bioadhesion time than XGM. The disulfide link that forms between mucus and thiolated XGM explains why it has better mucoadhesive properties than XGM. A study on in vitro miconazole (MCZ) release using phosphate buffer (pH 6.8) found that TXGM nanoparticles released MCZ more steadily than MCZ dispersion did. A 1-fold increase in the permeation of MCZ was observed from nanoparticles using albino rat intestine compared to MCZ. Albino rats were used to test the pharmacokinetics of MCZ, and the results showed a 4.5-fold increase in bioavailability. In conclusion, the thiolation of XGM enhances its bioavailability, controlled release of MCZ for a long period of time, and mucoadhesive activity.

Biomolecules based hydrogels and their potential biomedical applications: A comprehensive review

The need for biocompatible drug carriers has been significantly increased from the past few years. Researchers show great interest in the development of more versatile and sophisticated biomaterials based drug carriers. Hydrogels are beneficial drug carriers and easily release the controlled amount of drug at target site due to its tunable structure. The hydrogels made-up of potent biological macromolecules including collagen, gelatin, fibrin, elastin, fibroin, chitosan, starch, alginate, agarose and carrageenan have been proven as versatile biomaterials. These are three-dimensional polymeric networks, synthesized by crosslinking of hydrophilic polymers. The biological macromolecules based hydrogels containing therapeutic substances are used in a wide range of biomedical applications including wound healing, tissue engineering, cosmetics and contact lenses. However, many aspects related to hydrogels such as the mechanism of cross-linking and molecular entanglement are not clear. So, there is a need to do more research and exploration toward the extensive and cost-effective use of hydrogels. The present review article elaborately discusses the biomolecules based hydrogels and their possible biomedical applications in different fields.

Tailoring the Swelling-Shrinkable Behavior of Hydrogels for Biomedical Applications

Hydrogels with tailor-made swelling-shrinkable properties have aroused considerable interest in numerous biomedical domains. For example, as swelling is a key issue for blood and wound extrudates absorption, the transference of nutrients and metabolites, as well as drug diffusion and release, hydrogels with high swelling capacity have been widely applicated in full-thickness skin wound healing and tissue regeneration, and drug delivery. Nevertheless, in the fields of tissue adhesives and internal soft-tissue wound healing, and bioelectronics, non-swelling hydrogels play very important functions owing to their stable macroscopic dimension and physical performance in physiological environment. Moreover, the negative swelling behavior (i.e., shrinkage) of hydrogels can be exploited to drive noninvasive wound closure, and achieve resolution enhancement of hydrogel scaffolds. In addition, it can help push out the entrapped drugs, thus promote drug release. However, there still has not been a general review of the constructions and biomedical applications of hydrogels from the viewpoint of swelling-shrinkable properties. Therefore, this review summarizes the tactics employed so far in tailoring the swelling-shrinkable properties of hydrogels and their biomedical applications. And a relatively comprehensive understanding of the current progress and future challenge of the hydrogels with different swelling-shrinkable features is provided for potential clinical translations.

A comprehensive review on the COVID-19 vaccine and drug delivery applications of interpenetrating polymer networks

An interpenetrating polymer network (IPNs) is a concoction of two or more polymers (natural, synthetic, and/or a combination of both) in which at least one polymer is synthesized or crosslinked in the intimate presence of the other. These three-dimensional networked systems have gained prominence in a series of biomedical applications, especially in the last two decades. The last decades witnessed a surge in the meaningful applications of interpenetrating polymer networks, especially in drug delivery as simple IPN systems advanced and resulted in the formation of highly efficient microspheres, nanoparticles, nanogels, and hydrogels, intelligent enough to sense and respond to changes in external stimuli such as temperature, pH, and ionic strength. The structure of the polymers, crosslinking agents, crosslinking density, and polymerization method play an integral role in determining the properties and application of IPNs in drug delivery. This review article is a modest effort to highlight the importance and applications of different types of interpenetrating polymer networks for the sustained, site-specific drug delivery of various therapeutic formulations, as witnessed in scientific research literature over the past 22 years (2000-2022). A special section of the manuscript is devoted to studying the efficacy of network polymers in vaccine delivery and highlighting the future scope (if any) of incorporating the IPN system in COVID-related vaccine/drug delivery. Four key focus areas in this review article [1, 2].

Recent insights into polysaccharide-based hydrogels and their potential applications in food sector: A review

Hydrogels are ideal for various food applications because of their softness, elasticity, absorbent nature, flexibility, and hygroscopic nature. Polysaccharide hydrogels are particularly suitable because of the hydrophilic nature, their food compatibility, and their non-immunogenic character. Such hydrogels offer a wide range of successful applications such as food preservation, pharmaceuticals, agriculture, and food packaging. Additionally, polysaccharide hydrogels have proven to play a significant role in the formulation of food flavor carrier systems, thus diversifying the horizons of newer developments in food processing sector. Polysaccharide hydrogels are comprised of natural polymers such as alginate, chitosan, starch, pectin and hyaluronic acid when crosslinked physically or chemically. Hydrogels with interchangeable, antimicrobial and barrier properties are referred to as smart hydrogels. This review brings together the recent and relevant polysaccharide research in these polysaccharide hydrogel applications areas and seeks to point the way forward for future research and interventions. Applications in carrying out the process of flavor carrier system directly through their incorporation in food matrices, broadening the domain for food application innovations. The classification and important features of polysaccharide-based hydrogels in food processing are the topics of the current review study.

A novel environmentally friendly nanocomposite aerogel based on the semi-interpenetrating network of polyacrylic acid into Xanthan gum containing hydroxyapatite for efficient removal of methylene blue from wastewater

Eco-friendly nanocomposite aerogels were prepared as adsorbents for the removal of a model pollutant (methylene blue, MB) from water. These aerogels were comprised of hydroxyapatite (HA) nanoparticles embedded within a polymer matrix consisting of a semi-interpenetrating network of xanthan gum (XG) and polyacrylic acid (PAA). Microscopy and BET analysis showed that the aerogels formed had a nanofibrous porous microstructure with a surface area of 89 m²/g. Rheological analysis showed that the aerogels were viscoelastic materials whose elasticity increased with increasing HA concentration (up to 5 w/w%). The aerogels were effective at removing MB from water, exhibiting an adsorption capacity of 130 mg/g after 200 min. The binding of the MB to the aerogels was mainly attributed to hydrogen bonding and electrostatic attraction. A reusability test showed that the MB removal efficiency of over 86% was preserved after 10 cycles of adsorption-desorption. These results suggest that our nanocomposite aerogels may be useful for the efficient removal of anionic pollutants from wastewater and water supplies due to their ease of synthesis, cost-effectiveness, good mechanical properties, high thermal stability, and good adsorption performance.

Development of superabsorbent hydrogel based on Gum Arabic for enhanced removal of anxiolytic drug from water

The growing consumption of anxiolytic drugs like diazepam (DZP) has aggravated the problem of persistent organic pollutants in water. Due to its characteristics, the removal of DZP from water and wastewater is a challenging task. As an effort to deals with this issue, in this study, we report the development of a hydrogel based on Gum Arabic (GA) grafted with poly(acrylic acid) (GA-g-PAAc) to be used in the adsorptive removal of DZP from water. The hydrogel formation was confirmed by Fourier-transform infrared (FTIR) spectroscopy and thermal analysis (TGA/DTG) analyses. Images obtained by scanning electron microscopy (SEM) revealed that GA-g-PAAc hydrogel exhibits a porous morphology while swelling experiments suggest a superabsorbent characteristic (degree of swelling> 600%). From batch experiments, it was found that the removal of DZP reached remarkable percentages (>80%) before 300 min in moderate experimental conditions (pH 7, 25 °C, 150 mg of adsorbent). The adsorption of DZP on GA-g-PAAc followed the pseudo-first order kinetics, and the mechanism was described by the linear Langmuir isotherm. The maximum adsorption capacity (q_max) was calculated to be 15.16 mg g^-1 (at 25 °C), which is comparable or superior to other adsorbent materials used in DZP removal. Reuse experiments showed that GA-g-PAAc keeps appreciable adsorption ability even after five reuse cycles. The results reported here suggest this superabsorbent hydrogel could be a promising adsorbent material to treat water contaminated by anxiolytic drugs, like DZP.

Recent advances in the production of biomedical systems based on polyhydroxyalkanoates and exopolysaccharides

In recent years, growing attention has been devoted to naturally occurring biological macromolecules and their ensuing application in agriculture, cosmetics, food and pharmaceutical industries. They inherently have antigenicity, low immunogenicity, excellent biocompatibility and cytocompatibility, which are ideal properties for the design of biomedical devices, especially for the controlled delivery of active ingredients in the most diverse contexts. Furthermore, these properties can be modulated by chemical modification via the incorporation of other (macro)molecules in a random or controlled way, aiming at improving their functionality for each specific application. Among the wide variety of natural polymers, microbial polyhydroxyalkanoates (PHAs) and exopolysaccharides (EPS) are often considered for the development of original biomaterials due to their unique physicochemical and biological features. Here, we aim to fullfil a gap on the present associated literature, bringing an up-to-date overview of ongoing research strategies that make use of PHAs (poly (3-hydroxybutyrate), poly (3-hydroxybutyrate-co-3-hydroxyvalerate), poly (3-hydroxyoctanoate), poly(3-hydroxypropionate), poly (3-hydroxyhexanoate-co-3-hydroxyoctanoate), and poly (3-hydroxybutyrate-co-3-hydroxyhexanoate)) and EPS (bacterial cellulose, alginates, curdlan, pullulan, xanthan gum, dextran, hyaluronan, and schizophyllan) as sources of interesting and versatile biomaterials. For the first time, a monograph addressing the properties, pros and cons, status, challenges, and recent progresses regarding the application of these two important classes of biopolymers in biomedicine is presented.

Superabsorbent Hydrogels Based to Polyacrylamide/Cashew Tree Gum for the Controlled Release of Water and Plant Nutrients

Agricultural production is influenced by the water content in the soil and availability of fertilizers. Thus, superabsorbent hydrogels, based on polyacrylamide, natural cashew tree gum (CG) and potassium hydrogen phosphate (PHP), as fertilizer and water releaser were developed. The structure, morphology, thermal stability and chemical composition of samples of polyacrylamide and cashew tree gum hydrogels with the presence of fertilizer (HCGP) and without fertilizer (HCG) were investigated, using X-ray diffractometry (XRD), Fourier Transformed Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Thermogravimetric Analysis (TGA/DTG) and Energy Dispersive Spectroscopy (EDS). Swelling/reswelling tests, textural analysis, effect of pH, release of nutrients and kinetics were determined; the ecotoxicity of the hydrogels was investigated by the Artemia salina test. The results showed that PHP incorporation in the hydrogel favored the crosslinking of chains. This increased the thermal stability in HCGP but decreased the hardness and adhesion properties. The HCGP demonstrated good swelling capacity (~15,000 times) and an excellent potential for reuse after fifty-five consecutive cycles. The swelling was favored in an alkaline pH due to the ionization of hydrophilic groups. The sustained release of phosphorus in HCGP was described by the Korsmeyer-Peppas model, and Fickian diffusion is the main fertilizer release mechanism. Finally, the hydrogels do not demonstrate toxicity, and HCGP has potential for application in agriculture.

Preparation of Surface-Reinforced Superabsorbent Polymer Hydrogel Microspheres via Incorporation of In Situ Synthesized Silver Nanoparticles

Superabsorbent polymer (SAP) particles are primarily applied for absorbing and storing liquids. Here, poly (acrylic acid) (PAA)-based SAP microspheres incorporated with silver nanoparticles (AgNPs) are prepared as an effort to maintain microsphere shape during swelling and minimize gel blocking. PAA-based SAP spheres are synthesized via inverse suspension polymerization. AgNPs are formed within SAP spheres through in situ reduction of silver nitrate (AgNO3), using polyvinylpyrrolidone as the reducing agent. The formation of AgNPs within SAP was observed via techniques such as scanning electron microscopy, ultraviolet-visible spectroscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy and transmission electron microscopy. Energy dispersive spectroscopy analyses reveal that thin and dense layers of AgNPs are formed on the outer regions of the SAP spheres at higher concentrations of AgNO3. The water absorbency capacity decreases on increasing the amount of incorporated silver nanoparticles; however, it is comparable with that of commercially available surface-crosslinked SAP particles. Finally, micro-computerized tomography (micro-CT) study revealed that AgNP-incorporated SAP spheres maintained their shapes during swelling and exhibit higher void fractions in the packed gel bed, minimizing gel blocking and improving fluid permeability.

Step-by-step design of poly (ε-caprolactone) /chitosan/Melilotus officinalis extract electrospun nanofibers for wound dressing applications

Composition of polymers and choosing the type of solvents in electrospinning systems is of great importance to achieve a mat with optimal properties. In this work, with emphasizing the influence of a novel solvent system, an electrospun wound dressing was designed in four steps. Firstly, to study the effect of polymer-solvent interactions and electrospinning distance, a constant amount of polycaprolactone (PCL) was dissolved at different compositions of formic acid (FA)/dichloromethane (DCM) and was electrospun at different distances. The composition of 80FA/20DCM and distance of 15 cm were selected as optimal conditions by lowest average diameter of fibers and simultaneously good surface uniformity. In the second step, the concentration of PCL was considered variable to achieve the lowest diameter of fibers. Finally, in the third and fourth steps, different concentrations of chitosan (CN) and constant dosage of Melilotus officinalis (MO) extract were added to the solution. The extract contained fibers had a mean diameter of 275 ± 41 nm which is in the required condition for wound caring. Eventually, the optimized PCL/CN and PCL/CN/MO specimens were evaluated by FTIR, DSC, Tensile, water contact angle, antibacterial assays, cell viability, and drug release analysis for determining their function and properties.

Synthesis and application of eco-friendly superabsorbent composites based on xanthan gum and semi-coke

An eco-friendly superabsorbent composites of xanthan gum-g-polyacrylic acid/semi-coke (XG-g-PAA/SC) were fabricated via grafting of polyacrylic acid onto the XG in the presence of SC. The obtained products were characterized in combination with Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). The result indicated that the SC interacted with the polymeric network by hydrogen bond or electrostatic interaction. The swelling ratio of the best sample XG-g-PAA/SC (15 wt%) in distilled water and 0.9 wt% NaCl solution was 410.8 and 61.5 g/g by optimizing the polymerization conditions. In addition, compared with the blank sample (only containing soil), it can be found that adding a certain amount of XG-g-PAA/SC can significantly improve the soil water retention efficiency, which can be further proved by the results of plant pot experiment. Based on the above excellent swelling capacity, water holding capacity and plant growth promoting performance, it can be inferred that the XG-g-PAA/SC is expected to become a water retaining agent or soil regulator for plant growth.

Nanocomposite scaffolds composed of Apacite (apatite-calcite) nanostructures, poly (ε-caprolactone) and poly (2-hydroxyethylmethacrylate): The effect of nanostructures on physico-mechanical properties and osteogenic differentiation of human bone marrow mesenchymal stem cells in vitro

Nanocomposite scaffolds were fabricated from poly (ε-caprolactone) (PCL), Poly (2-hydroxyethylmethacrylate) (PHEMA), and Apacite (Apatite-calcite) nanostructures (15 and 25 wt%). The nanoscale structure, physical and chemical properties, mechanical properties, hydrophilic behavior, degradability and osteogenic properties of the fabricated scaffolds were evaluated. The results showed that the mechanical strength, degradation, wetting ability, and mechanical strength of PCL-PHEMA scaffolds significantly increases upon inclusion of Apacite nanoparticles up to 25 wt%. Accordingly, the best mechanical values (E ~ 7.109 MPa and σ ~ 0.414 MPa) and highest degradability (32% within 96 h) were recorded for PCL-PHEMA scaffolds containing 25 wt% of Apacite. Furthermore, highest porosity and roughness were observed in the PCL-PHEMA/25% Apacite as a result of the Apacite nanoparticles inclusion. There was no cytotoxicity recorded for the fabricated scaffolds based on the results obtained from MTT assay and acridine orange staining. Alkaline phosphatase activity, calcium content quantification, Van Kossa staining, FESEM and real time PCR tests confirmed the biomineralization, and the differentiation potential of the nanocomposite scaffolds. Overall, the 3D structure, optimum porosity and balanced dissolution rate of PCL-PHEMA/25% Apacite providing a balanced microenvironment resulted in improved cell adhesion, cell behavior, and replication, as well as osteogenic induction of human bone-marrow-derived mesenchymal stem cells (hBM-MSCs).

Preparation and characterization of semi-IPNs of polycaprolactone/poly (acrylic acid)/cellulosic nanowhisker as artificial articular cartilage

Cartilage is a semi-solid resilient and smooth elastic connective tissue and upon damage, its repair is almost impossible or occurs with a very slow recovery process. Polycaprolactone (PCL), used as a biocompatible polymer, withholds all required mechanical properties, except suitable cell adhesion due to its hydrophobicity. In order to resolve this issue, we sought to introduce appropriate semi-IPNs into the system to regain its hydrophilicity base on increasing of the hydrophilic polymer. PCL and Cellulose nanowhiskers (CNWs) were entrapped in a network of poly (acrylic acid) that had been crosslinked via a novel acrylic-urethane crosslinker. The influential synthetic parameters on the preparation of artificial articular cartilages were investigated based on the Taguchi test design. The prepared CNW, acrylic-urethane crosslinker and semi-IPNs were studied via ¹H NMR, FTIR, SEM, TEM, TGA, water swelling, water contact angle, tensile, and MTT analyses. According to the results, the optimal amount of monomer was about 46%. Incorporation of an optimized amount of CNW, which was 0.5%, improved the mechanical properties of artificial cartilage. After a 30 h time period, semi-IPNs showed the water absorption of about 30%. MTT on days 1, 3 and 5, as well as cell attachment, confirmed the biocompatibility of the semi-IPNs.