Novel cationic polymer modified magnetic chitosan beads for efficient adsorption of heavy metals and dyes over a wide pH range

Adsorption of ionic contaminants from complex water matrices by versatile chitosan-based beads

Most adsorbents are currently restricted by their single function in pollutant removal from complex wastewater. Herein, we constructed a versatile chitosan-based adsorbent (MC-DA) by grafting amphoteric copolymers with high pH-responsiveness property, aiming at the removal of multiple ionic contaminants. Specifically, the surface charge and hydrophobicity/hydrophilicity of MC-DA can be finely tuned under different pH conditions. As a result, the effective adsorption of cationic methylene blue (MB) and anionic Acid Orange 7 (AO7) with capacities of 627.4 mg/g and 1146.8 mg/g were achieved respectively, superior to most reported materials. Regarding the characterization results, the adsorption mechanisms for MB adsorption were electrostatic and hydrophobic interactions, while the electrostatic attraction was the main driving force for AO7 adsorption. Apart from the versatile adsorption performance, high acid resistance (pH ≥ 2.0), good reusability and rapid separation property under an external magnetic field suggested MC-DA's promising environmental benefits and practical application potential in water remediation.

Effective removal of Cu(II) from water by three-dimensional composite microspheres based on chitosan/sodium alginate/silicon dioxide: Adsorption performance and mechanism

Chitosan (CS) is commonly used as an adsorbent for removing Cu(II) from water, but it has drawbacks such as solubility in dilute acid, difficulty in recycling in powder form, and short service life. This study utilized sodium alginate (SA) as a gel carrier to encapsulate CS, combined with silicon dioxide (SiO2) to improve mechanical stability. The preparation of CS/SA/SiO2 (SSC1.0) involved physical blending, CaCl2 cross-linking, and freeze-drying. Characterization methods such as SEM-EDS, FTIR, BET, and XRD were used to analyze the structural composition of SSC1.0. The material exhibited a folded surface, porous internal cross-section, nitrogen/oxygen-containing functional groups, and thermal stability in high temperatures and various aqueous environments. The adsorption performance of SSC1.0 on Cu(II) was evaluated under different conditions, showing a maximum adsorption capacity of 47.50 mg/g. The material maintained a removal rate above 70 % after 5 cycles. SSC1.0 also showed the highest removal rate of Cu(II) when applied to mine wastewater treatment. Adsorption modeling indicated that the process was driven by chemical reactions and was spontaneous and heat-absorbing.'

The impact of copper nanoparticles surfactant on the structural and biological properties of chitosan/sodium alginate wound dressings

Multifunctional wound dressings based on hydrogels are an efficacious and practicable strategy in therapeutic processes and accelerated chronic wound healing. Here, copper (Cu) nanoparticles were added to chitosan/sodium alginate (CS/SA) hydrogels to improve the antibacterial properties of the prepared wound dressings. Due to the super-hydrophobicity of Cu nanoparticles, polyethylene glycol (PEG) was used as a surfactant, and then added to the CS/SA-based hydrogels. The CS/SA/Cu hydrogels were synthesized with 0, 2, 3.5, and 5 wt% Cu nanoparticles. The structural and morphological properties in presence of PEG were evaluated using Fourier-transform infrared spectroscopy (FTIR), Differential scanning calorimetry (DSC), and field emission scanning electron microscopy (FESEM). The biodegradation and swelling properties of the hydrogels were investigated in phosphate buffer saline (PBS) at 37 °C for up to 30 days. Cell viability and adhesion, as well as antibacterial behavior, were investigated via MTT assay, FESEM, and disk diffusion method, respectively. The obtained results showed that PEG provided new intra- and intermolecular bonds that affected significantly the hydrogels' degradation and swelling ratio, which increased up to ~1200 %. Cell viability reached ~110 % and all samples showed remarkable antibacterial behavior when CS/SA/Cu containing 2 wt% was introduced. This study provided new insights regarding the use of PEG as a surfactant for Cu nanoparticles in CS/SA hydrogel wound dressing, ultimately affecting the chemical bonding and various properties of the prepared hydrogels.

Surface modified of chitosan by TiO2@MWCNT nanohybrid for the efficient removal of organic dyes and antibiotics

Considering the increase in the discharge of industrial effluents containing dyes and antibiotic resistance as a consequence of increasing the prescription and easy distribution of antibiotic drugs at the global level, designing efficient, biodegradable and non-toxic absorbents is necessary to reduce environmental harm effects. Herein, we present a series of novel eco-friendly ternary hybrid nanocomposite hydrogels CS/TiO2@MWCNT (CTM) composed of chitosan (CS), TiO2, and multiwalled carbon nanotube (MWCNT) for removal of methylene blue (MB) and methyl orange (MO) and common antibiotic ciprofloxacin (CIP) in aqueous medium. The combination of MWCNT and TiO2 improves the physicochemical properties of CS hydrogel and increases the adsorption capacity toward pollutants in the presence of different loadings. CTM hydrogel showed a specific surface area of 236.45 m2 g-1 with a pore diameter of 7.89 nm. Adsorption mechanisms were investigated in detail using kinetic, isotherm, and thermodynamic studies of adsorption as well as various spectroscopic techniques. Adsorption of these pollutants by CTM nanocomposite hydrogel occurred using various interactions at different pHs, which showed the obvious dependence of CTM adsorption capacity on pH. Electrostatic attractions, complex formation, π-π stacking and hydrogen bonds played a key role in the adsorption process. The adsorption of MB, MO, and CIP was fitted with the Langmuir isotherm with maximum adsorption capacities of 531.91, 1763.6, and 1510.5 mg g-1, respectively. CTM had a minor decrease in adsorption strength and showed good structural stability even after 8 adsorptions-desorption cycles. The total cost of producing a 1 kg adsorbent was calculated to be $ 450, which helped us determine the economic feasibility of the adsorbent in large-scale applications.

Construction of CS-SDAEM long-chain polysaccharide derivative on TA@CNTs coated PVDF membrane with effective oil-water emulsion purification and low contamination rate

Currently, the most effective way to improve the anti-fouling performance of water treatment separation membrane is to enhance the hydrophilicity of the membrane surface, but it can still cause contamination, leading to the occurrence of flux reduction. The construction of a strong hydration layer to resist wastewater contamination is still a challenging task. In this study, a defect-free hydration layer barrier was achieved by grafting chitosan polysaccharide derivatives (CS-SDAEM) on the membrane, which achieved in effective fouling prevention and low flux decline rate. A layer of tannic acid-coated carbon nanotubes (TA@CNTs) has been uniformly deposited on the commercial PVDF membrane so that the surface was rich in -COOH groups, providing sufficient reaction sites. These reactive groups facilitate the grafting of amphiphilic polymers onto the membrane. This modification strategy achieved in enhancing the antifouling performance. The modified membrane achieved low contamination rate with DR of 16.9 % for wastewater filtration, and the flux recovery rate was above 95 % with PWF of 1100 (L·m-2·h-1). The membrane had excellent anti-fouling performance, which provided a new route for the future development of water treatment membrane.

Simultaneous removal of ammonium, phosphate, and phenol via self-assembled biochar composites CBCZrOFe3O4 and its utilization as soil acidity amelioration

High concentrations of ammonium, phosphate, and phenol are recognized as water pollutants that contribute to the degradation of soil acidity. In contrast, small quantities of these nutrients are essential for soil nutrient cycling and plant growth. Here, we reported composite materials comprising biochar, chitosan, ZrO, and Fe3O4, which were employed to mitigate ammonium, phosphate, and phenol contamination in water and to lessen soil acidity. Batch adsorption experiments were conducted to assess the efficacy of the adsorbents. Initially, comparative studies on the simultaneous removal of NH4, PO4, and phenol using CB (biochar), CBC (biochar + chitosan), CBCZrO (biochar + chitosan + ZrO), and CBCZrOFe3O4 (biochar + chitosan + ZrO + Fe3O4) were conducted. The results discovered that CBCZrOFe3O4 exhibited the highest removal percentage among the adsorbents (P < 0.05). Adsorption data for CBCZrOFe3O4 were well fitted to the second-order kinetic and Freundlich isotherm models, with maximum adsorption capacities of 112.65 mg/g for NH4, 94.68 mg/g for PO4 and 112.63 mg/g for phenol. Subsequently, the effect of CBCZrOFe3O4-loaded NH4, PO4, and phenol (CBCZrOFe3O4-APP) on soil acidity was studied over a 60-day incubation period. The findings showed no significant changes (P < 0.05) in soil exchangeable acidity, H+, Mg, K, and Na. However, there was a substantial increase in the soil pH, EC, available P, CEC, N-NH4, and N-NO3. A significant reduction was also observed in the available soil exchangeable Al and Fe (P < 0.05). This technique demonstrated multi-functionality in remediating water pollutants and enhancing soil acidity.

Enhancing Oral Bioavailability of Simvastatin Using Uncoated and Polymer-Coated Solid Lipid Nanoparticles

Simvastatin (SVA) is a well-prescribed drug for treating cardiovascular and hypercholesterolemia. Due to the extensive hepatic first-pass metabolism and poor solubility, its oral bioavailability is 5%. Solid lipid nanoparticles (SLNs) and hydrogel-coated SLNs were investigated to overcome the limited bioavailability of SVA. Four different lipids used alone or in combination with two stabilizers were employed to generate 13 SLNs. Two concentrations of chitosan (CS) and alginate (AL) were coating materials. SLNs were studied for particle size, zeta potential, in vitro release, rheology, and bioavailability. The viscosities of both the bare and coated SLNs exhibited shear-thinning behavior. The viscosity of F11 (Chitosan 1%) at 20 and 40 rpm were 424 and 168 cp, respectively. F11 had a particle size of 260.1 ± 3.72 nm with a higher release; the particle size of F11-CS at 1% was 524.3 ± 80.31 nm. In vivo studies illustrated that F11 had the highest plasma concentration when compared with the SVA suspension and coated chitosan (F11 (Chitosan 1%)). Greater bioavailability is measured as (AUC0→24), as compared to uncoated ones. The AUC for F11, F11-CS 1%, and the SVA suspension were 1880.4, 3562.18, and 272 ng·h/mL, respectively. Both bare and coated SLNs exhibited a significantly higher relative bioavailability when compared to that from the control SVA.

Biopolymer-based beads for the adsorptive removal of organic pollutants from wastewater: Current state and future perspectives

Among biopolymer-based adsorbents, composites in the form of beads have shown promising results in terms of high adsorption capacity and ease of separation from the effluents. This review addresses the potential of biopolymer-based beads to remediate wastewaters polluted with emerging organic contaminants, for instance dyes, active pharmaceutical ingredients, pesticides, phenols, oils, polyaromatic hydrocarbons, and polychlorinated biphenyls. High adsorption capacities up to 2541.76 mg g-1 for dyes, 392 mg g-1 for pesticides and phenols, 1890.3 mg g-1 for pharmaceuticals, and 537 g g-1 for oils and organic solvents have been reported. The review also attempted to convey to its readers the significance of wastewater treatment through adsorption by providing an overview on decontamination technologies of organic water contaminants. Various preparation methods of biopolymer-based gel beads and adsorption mechanisms involved in the process of decontamination have been summarized and analyzed. Therefore, we believe there is an urge to discuss the current state of the application of biopolymer-based gel beads for the adsorption of organic pollutants from wastewater and future perspectives in this regard since it is imperative to treat wastewater before releasing into freshwater bodies.

Adsorption of Cd (II) ions and methyl violet dye by using an agar-graphene oxide nano-biocomposite

In this work, an agar-graphene oxide hydrogel was prepared to adsorb Cd (II) and Methyl Violet (MV) from water. The hydrogel was synthesised and characterised through SEM and EDS. Kinetic, equilibrium and regeneration studies were carried out, in which Langmuir, Freundlich and Sips isotherm models were fitted to the equilibrium experimental data; and regarding the kinetics, studies were conducted by modelling experimental data considering both empirical and phenomenological models. SEM and EDS have shown the composite present a 3D-disordered porous microstructure and that it is mainly constituted of C and O. Sips model fitted well to Cd (II) (R2 = 0.968 and χ2 =  0.176) and MV (R2 = 0.993 and χ2 =  0.783). The qmax values for MV and Cd (II) were 76.65 and 11.70 mg.g-1, respectively. Pseudo-order models satisfactorily described Cd (II) and MV adsorption kinetics with R2 > 0.90. Regeneration experiments revealed an outstanding reuse capacity of the adsorbent after three cycles of adsorption-desorption for both Cd (II) and MV. This study evidences the possibility of a feasible adsorbent for Cd (II) and MV removal from water for successive cycles of use.

The performance of quaternary-ammonium chitosan in wastewater treatment: The overlooked role of solubility

Quaternary-ammonium chitosan (CT-CTA) is a popular water treatment agent, and its electropositivity and cation strength are improved compared with chitosan. The use of CT-CTA is widely advocated to remove suspended particles and organic matter from wastewater. However, the solubility of CT-CTA is an important factor affecting the performance of CT-CTA, which is a neglected problem in previous studies. In the study, CT-CTA with different solubilities were prepared by adjusting pH from 2 to 7 in preparation, and their applications were explored in wastewater. When the pH was 2, 2.5, or 3, the obtained CT-CTA was a dissolved state. The turbidity and color removal were 95 % - 98 % and 60 % - 74 %, respectively. When the pH was 4, 5, 6, or 7, the obtained CT-CTA was a solid state. The turbidity and color removal were 30 % - 63 % and 90 % - 97 %, respectively. For domestic-wastewater treatment, CT-CTA in a dissolved state removed 92 % of turbidity and 50 % of chemical oxygen demand (COD). CT-CTA in a solid state removed 86 % of turbidity and 64 % of COD with poly aluminum chloride (PAC). The results illustrated the performance of CT-CTA with different solubilities, which can broaden its application in wastewater treatment.

Sorption behavior of chitosan nanoparticles for single and binary removal of cationic and anionic dyes from aqueous solution

In this study, chitosan nanoparticles (ChNs) were used as an adsorbent for single and simultaneous uptake of cationic (methylene blue (MB)) and anionic (methyl orange (MO)) dyes. ChNs were prepared based on the ionic gelation method using sodium tripolyphosphate (TPP) and characterized by zetasizer, FTIR, BET, SEM, XRD, and pHPZC. The studied parameters that affect removal efficiency included pH, time, and dyes' concentration. The results showed that in single-adsorption mode, the removal of MB is better in alkaline pH, contrary to MO uptake which presents higher removal efficiency in acidic media. The simultaneous removal of MB and MO from the mixture solution by ChNs could be achieved under neutral conditions. The adsorption kinetic results showed that adsorption of MB and MO for both single-adsorption and binary adsorption systems comply with the pseudo-second-order model. Langmuir, Freundlich, and Redlich-Peterson isotherms were used for the mathematical description of single-adsorption equilibrium, while non-modified Langmuir and extended Freundlich isotherms were used to fit the co-adsorption equilibrium results. The maximum adsorption capacities of MB and MO in a single dye adsorption system were 315.01 and 257.05 mg/g for MB and MO, respectively. On the other hand, and for binary adsorption system, the adsorption capacities were 49.05 and 137.03 mg/g, respectively. The adsorption capacity of MB decreases in solution containing MO and vice versa, suggesting an antagonistic behavior of MB and MO on ChNs. Overall, ChNs could be a candidate for single and binary removal of MB and MO in dye-containing wastewater.

Nano‑selenium functionalized chitosan gel beads for Hg(II) removal from apple juice

The presence of potentially toxic elements and compounds poses threats to the quality and safety of fruit juices. Among these, Hg(II) is considered as one of the most poisonous heavy metals to human health. Traditional chitosan-based and selenide-based adsorbents face challenges such as poor adsorption capacity and inconvenient separation in juice applications. In this study, we prepared nano‑selenium functionalized chitosan gel beads (nanoSe@CBs) and illustrated the synergistic promotions between chitosan and nanoSe in removing Hg(II) from apple juice. The preparation conditions, adsorption behaviors, and adsorption mechanism of nanoSe@CBs were systematically investigated. The results revealed that the adsorption process was primarily controlled by chemical adsorption. At the 0.1 % dosage, the adsorbent exhibited high uptake, and the maximum adsorption capacity from the Langmuir isotherm model could reach 376.5 mg/g at room temperature. The adsorbent maintained high adsorption efficiency (> 90 %) across a wide range of Hg(II) concentrations (0.01 to 10 mg/L) and was unaffected by organic acids present in apple juice. Additionally, nanoSe@CBs showed negligible effects on the quality of apple juice. Overall, nanoSe@CBs open up possibilities to be used as a safe, low-cost and highly-efficient adsorbent for the removal of Hg(II) from juices and other liquid foods.

Chitosan-Based Beads Incorporating Inorganic-Organic Composites for Copper Ion Retention in Aqueous Solutions

In recent years, there has been a challenging interest in developing low-cost biopolymeric materials for wastewater treatment. In the present work, new adsorbents, based on different types of chitosan (commercial, commercial chitin-derived chitosan and chitosan synthesized from shrimp shell waste) and inorganic-organic composites have been evaluated for copper ions removal. The efficacy of the synthesis of chitosan-based composite beads has been determined by studying various characteristics using several techniques, including FTIR spectroscopy, X-ray diffraction, porosimetry (N2 adsorption), and scanning electron microscopy (SEM). Adsorption kinetics was performed using different adsorption models to determine the adsorption behavior of the materials in the aqueous media. For all composite beads, regardless of the type of chitosan used, good capacity to remove copper ions from simulated waters was observed (up to 17 mg/g), which proves that the new materials hold potential for heavy metal retention. However, the adsorption efficiency was influenced by the type of chitosan used. Thus, for the series where commercial chitosan (CC) was used, the removal efficiency was approximately 29%; for the series with chitosan obtained from commercial chitin (SC), the removal efficiency was approximately 34%; for the series with chitosan enriched with CaCO3 (SH), the removal efficiency was approximately 52%.

Recent advances in cellulose-based sustainable materials for wastewater treatment: An overview

Water pollution presents a significant challenge, impacting ecosystems and human health. The necessity for solutions to address water pollution arises from the critical need to preserve and protect the quality of water resources. Effective solutions are crucial to safeguarding ecosystems, human health, and ensuring sustainable access to clean water for current and future generations. Generally, cellulose and its derivatives are considered potential substrates for wastewater treatment. The various cellulose processing methods including acid, alkali, organic & inorganic components treatment, chemical treatment and spinning methods are highlighted. Additionally, we reviewed effective use of the cellulose derivatives (CD), including cellulose nanocrystals (CNCs), cellulose nano-fibrils (CNFs), CNPs, and bacterial nano-cellulose (BNC) on waste water (WW) treatment. The various cellulose processing methods, including spinning, mechanical, chemical, and biological approaches are also highlighted. Additionally, cellulose-based materials, including adsorbents, membranes and hydrogels are critically discussed. The review also highlighted the mechanism of adsorption, kinetics, thermodynamics, and sorption isotherm studies of adsorbents. The review concluded that the cellulose-derived materials are effective substrates for removing heavy metals, dyes, pathogenic microorganisms, and other pollutants from WW. Similarly, cellulose based materials are used for flocculants and water filtration membranes. Cellulose composites are widely used in the separation of oil and water emulsions as well as in removing dyes from wastewater. Cellulose's natural hydrophilicity makes it easier for it to interact with water molecules, making it appropriate for use in water treatment processes. Furthermore, the materials derived from cellulose have wider application in WW treatment due to their inexhaustible sources, low energy consumption, cost-effectiveness, sustainability, and renewable nature.

Enhanced removal of short- and long-chain per- and poly-fluoroalkyl substances from aqueous phase using crushed grafted chitosan beads: Performance and mechanisms

The widespread use of per- and poly-fluoroalkyl substances (PFASs), environmentally persistent halogenated hydrocarbons, in various industrial and commercial applications has caused significant concerns owing to their contamination of soil and groundwater. Chitosan is a biopolymer substance with abundant amine and hydroxyl functional groups, making it a good candidate for adsorption of PFASs. This study aimed to increase chitosan's adsorption capacity by grafting additional amine functional groups on its surface for the removal of long- and short-chain PFASs from an aqueous phase. Two types of chitosan-based sorbents were developed: crushed chitosan beads (CBs) and polyethyleneimine-grafted CBs (GCBs). Batch adsorption tests assessed the adsorption capacities of the sorbents in terms of the sorption kinetics, isotherms, selectivity, and reusability. Based on the results, the GCBs had significant potential for adsorbing PFASs. These capacities were significantly higher than those demonstrated by the CBs. The sorption kinetics data revealed that the GCBs had a fast sorption rate. Furthermore, the GCBs demonstrated a high adsorption affinity, with log Kd values ranging from 1.5 to 2.5 for PFASs at environmentally relevant concentrations (1000 ng L-1). They also demonstrated excellent selectivity sorption for these compounds, even in the presence of other organic and inorganic pollutants.

Construction of a multi-layer protection of CS polymer brush grafted DA@CNTs coating on PVDF membrane for effective removal of dye effluent

In the process of removing dye wastewater, the membrane surface is susceptible to contamination, resulting in reduced performance and limited dye separation efficiency. A single hydrophilic modification layer is not enough to achieve effective separation of different types of dyes. The present research designed a "double layer protection" method in order to overcome the above deficiencies. A solution of dopamine (DA) coated carbon nanotubes (CNTs-COOH) was covered on the surface of the polyvinylidene fluoride (PVDF) membrane by deposition, followed by grafting a layer of chitosan (CS) polymer brushes on its surface. The spatial double layer structure provides an excellent barrier effect and effectively reduces the contamination of dyes. When filtering different types of dyes, effective filtration of anionic and cationic dyes through the electrostatic effect of the first layer, the adsorption of CNTs in the second layer and the hydration layer of both layers. All membranes have excellent rejection properties. More importantly, the membranes also had good chemical and mechanical stability and their serviceability was not degraded. Therefore, the prepared PVDF-based multi-layer composite membranes behave a potential application prospect in the wastewater purification field.

Chitosan Hydrogels for Water Purification Applications

Chitosan-based hydrogels have gained significant attention for their potential applications in water treatment and purification due to their remarkable properties such as bioavailability, biocompatibility, biodegradability, environmental friendliness, high pollutants adsorption capacity, and water adsorption capacity. This article comprehensively reviews recent advances in chitosan-based hydrogel materials for water purification applications. The synthesis methods, structural properties, and water purification performance of chitosan-based hydrogels are critically analyzed. The incorporation of various nanomaterials into chitosan-based hydrogels, such as nanoparticles, graphene, and metal-organic frameworks, has been explored to enhance their performance. The mechanisms of water purification, including adsorption, filtration, and antimicrobial activity, are also discussed in detail. The potential of chitosan-based hydrogels for the removal of pollutants, such as heavy metals, organic contaminants, and microorganisms, from water sources is highlighted. Moreover, the challenges and future perspectives of chitosan-based hydrogels in water treatment and water purification applications are also illustrated. Overall, this article provides valuable insights into the current state of the art regarding chitosan-based hydrogels for water purification applications and highlights their potential for addressing global water pollution challenges.

A Comprehensive Review of Polysaccharide-Based Hydrogels as Promising Biomaterials

Polysaccharides have emerged as a promising material for hydrogel preparation due to their biocompatibility, biodegradability, and low cost. This review focuses on polysaccharide-based hydrogels' synthesis, characterization, and applications. The various synthetic methods used to prepare polysaccharide-based hydrogels are discussed. The characterization techniques are also highlighted to evaluate the physical and chemical properties of polysaccharide-based hydrogels. Finally, the applications of SAPs in various fields are discussed, along with their potential benefits and limitations. Due to environmental concerns, this review shows a growing interest in developing bio-sourced hydrogels made from natural materials such as polysaccharides. SAPs have many beneficial properties, including good mechanical and morphological properties, thermal stability, biocompatibility, biodegradability, non-toxicity, abundance, economic viability, and good swelling ability. However, some challenges remain to be overcome, such as limiting the formulation complexity of some SAPs and establishing a general protocol for calculating their water absorption and retention capacity. Furthermore, the development of SAPs requires a multidisciplinary approach and research should focus on improving their synthesis, modification, and characterization as well as exploring their potential applications. Biocompatibility, biodegradation, and the regulatory approval pathway of SAPs should be carefully evaluated to ensure their safety and efficacy.

Application of Box-Behnken Design to Optimize Phosphate Adsorption Conditions from Water onto Novel Adsorbent CS-ZL/ZrO/Fe3O4: Characterization, Equilibrium, Isotherm, Kinetic, and Desorption Studies

Phosphate (PO43-) is an essential nutrient in agriculture; however, it is hazardous to the environment if discharged in excess as in wastewater discharge and runoff from agriculture. Moreover, the stability of chitosan under acidic conditions remains a concern. To address these problems, CS-ZL/ZrO/Fe3O4 was synthesized using a crosslinking method as a novel adsorbent for the removal of phosphate (PO43-) from water and to increase the stability of chitosan. The response surface methodology (RSM) with a Box-Behnken design (BBD)-based analysis of variance (ANOVA) was implemented. The ANOVA results clearly showed that the adsorption of PO43- onto CS-ZL/ZrO/Fe3O4 was significant (p ≤ 0.05), with good mechanical stability. pH, dosage, and time were the three most important factors for the removal of PO43-. Freundlich isotherm and pseudo-second-order kinetic models generated the best equivalents for PO43- adsorption. The presence of coexisting ions for PO43- removal was also studied. The results indicated no significant effect on PO43- removal (p ≤ 0.05). After adsorption, PO43- was easily released by 1 M NaOH, reaching 95.77% and exhibiting a good capability over three cycles. Thus, this concept is effective for increasing the stability of chitosan and is an alternative adsorbent for the removal of PO43- from water.

Chitosan-g-polyacrylonitrile ZnO nano-composite, synthesis and characterization as new and good adsorbent for Iron from groundwater

The highly poisonous, non-biodegradable heavy metals present serious concern in wastewater environmental sustainability and human health. Using adsorption is an effective technology for the treatment of this kind of water. Therefore, developing efficient and cost-effective adsorbents considers a significant and an emerging topic in the field the water purification. Chitosan grafted polyacrylonitrile (Cs-g-PAN) was facially fabricated via graft polymerization using ammonium persulfate (APS) as the initiator. The simple ultrasonic technique was used for doping ZnO nanoparticles into the Cs-g-PAN matrix to prepare chitosan-grafted polyacrylonitrile/ZnO (Cs-g-PAN/ZnO). For comparative study, pure ZnO and nanocomposite of PAN doped with ZnO (PAN/ZnO) were also prepared. XRD, FTIR, SEM, TEM, BET, EDS, and TGA measurements were conducted to confirm the morphological and structural properties of the prepared materials. Cs-g-PAN/ZnO possesses a specific surface area of 20.23 m²/g with a pore size of 31.58 nm and pore volume of 0.16 cm³ g^-1. The adsorption behavior toward Fe(II) as a pollutant for groundwater was studied for the synthesized materials. The effect of pH (4-8), contact time (5-60 min), adsorbent dose (0.01-0.3 g), and different temperature degrees (278, 288, 298, 308, and 318 K) on the removal of iron (II) has been conducted. The removal efficiency was achieved 100 % under the optimum condition, at pH = 7, contact time 30 min, adsorbate concentration 0.93 mg/L, and adsorbent dosage 0.05 g/L at room temperature. Langmuir and Freundlich's isothermal and kinetic studies have been analyzed to determine the adsorption mechanism of Fe(II) ions on the synthesized nanomaterials. The adsorption process of Fe(II) over the surface of prepared catalysts proceeded via the Langmuir model and pseudo-second-order reaction kinetics with R² > 0.99. Suggesting the formation of Fe(II) monolayer over the adsorbent surface and the rate-limiting step is probably controlled by chemisorption through sharing the electrons between Fe⁺² and the prepared catalyst.

Developing nano-micro size chitosan beads using imidazolium-based ionic liquid: A perspective

The aggressive search for unique materials in recent years has put forward chitosan and modified-chitosan as materials with unique structural and morphological characteristics for various important applications. Just as imidazolium-based ionic liquids are the commonly applied ionic liquids (ILs) type for chitosan modifications for various applications, their further modifications into beads for enhancing their properties is now gaining most attention. However, most of the currently prepared imidazolium ILs modified-chitosan beads are not in nano size due to preparation difficulties. In response to this and referencing the research works in the literature, the possible breakthrough directions including synthesis routes, and physical and mechanical transformation processes are proposed. These procedures are expected to provide certain theoretical and empirical basis, as well as technical guide for developing nano-micro size chitosan beads using imidazolium based ILs.

Facile synthesis of chitosan-tartaric acid biosorbents for removal of Cu(II) and Cd(II) from water and tea beverages

Consumption of water and tea beverages leads to the intake of heavy metals by humans. Development of technology for decontamination greatly reduces the risks of the heavy metal exposure. In this study, environment-friendly chitosan-tartaric acid biosorbents (CTBs) were synthesized by a facile one-step cross-linking strategy to mitigate the Cu(II) and Cd(II) contamination in water and tea beverages. The cross linkage of tartaric acid and chitosan endowed CTBs with excellent properties in aspects of surface roughness, mechanical strength, and acid resistance. Adsorption performance and mechanism of CTBs were studied, and the Langmuir isotherm model and pseudo-second-order kinetic model were adhered during adsorption. Up to 90 % removal efficiencies of Cu(II) and Cd(II) from water and tea beverages by CTBs were achieved. Moreover, the adsorption showed only a slight reduction in the quality of tea beverages. This study offers a new insight for reduction of heavy metals-pollution in beverages.

Modified magnetic chitosan materials for heavy metal adsorption: a review

Magnetic chitosan materials have the characteristics of both chitosan and magnetic particle nuclei, showing the characteristics of easy separation and recovery, strong adsorption capacity and high mechanical strength, and have received extensive attention in adsorption, especially in the treatment of heavy metal ions. In order to further improve its performance, many studies have modified magnetic chitosan materials. This review discusses the strategies for the preparation of magnetic chitosan using coprecipitation, crosslinking, and other methods in detail. Besides, this review mainly summarizes the application of modified magnetic chitosan materials in the removal of heavy metal ions in wastewater in recent years. Finally, this review also discusses the adsorption mechanism, and puts forward the prospect of the future development of magnetic chitosan in wastewater treatment.

Magnetic Fe3O4 embedded chitosan-crosslinked-polyacrylamide composites with enhanced removal of food dye: Characterization, adsorption and mechanism

The water solubility in acid solution, relative low adsorption capacities and unsatisfactory separation performance limit application of traditional chitosan-based adsorbents in wastewater treatment. To break the limitation, a hydrophilic magnetic Fe₃O₄ embedded chitosan-crosslinked-polyacrylamide composites (abbreviated as m-CS-c-PAM) were prepared by a two-step method. The m-CS-c-PAM composites were systematically characterized using SEM, XRD, FTIR, VSM, TGA and BET. Sunset yellow (SY) was selected as model food dye to investigate adsorption kinetics and thermodynamic parameters of food dye adsorption onto m-CS-c-PAM. Compared with magnetic Fe₃O₄/chitosan, m-CS-c-PAM can adapt to a wider range of pH (2-10) and resist the presence of inorganic salts. m-CS-c-PAM was proved to have high adsorption capacity (359.71 mg g^-1) for SY dye at 298 K, much higher than magnetic Fe₃O₄/chitosan and many reported adsorbents. Moreover, m-CS-c-PAM could be rapidly and efficiently separated from treated solution within 15 s by an external magnet and regenerated by NaOH solution. With its excellent adsorption capacity, pH-independent adsorption capability for food dye, easy and convenient separation ability, satisfactory reusability, m-CS-c-PAM can be a promising material for food wastewater treatment.

A magnetic MIL-125-NH2@chitosan composite as a separable adsorbent for the removal of Cr(VI) from wastewater

Metal-organic frameworks (MOFs) are gradually used since of their huge specific surface area and superior pore structure. However, there are problems such as easy aggregation and difficult separation in water treatment. In this study, we prepared composite microspheres (FMCS-1) by modifying MIL-125-NH₂ with Fe₃O₄ and chitosan. The structural characterization and performance analysis of the materials showed that the introduction of chitosan effectively prevents the stacking of MOFs. The magnetic test manifested that Fe₃O₄ solved the problem of the difficult separation of MOFs from water. The removal potential of toxic Cr(VI) was tested by adsorption experiments. The isotherm model indicated that FMCS-1 is a single molecular layer adsorbent with a maximum adsorption capacity of 109.46 mg/g at pH = 2. The adsorption kinetics showed that the adsorption of Cr(VI) by FMCS-1 was chemical adsorption. The acid resistance test demonstrated that FMCS-1 can exist stably in acid solutions. The recycling experiments proved that the adsorbent can be reused and the removal percentage still reaches 50 % after 5 cycles. This work expands the application of MOFs in water treatment and also provides an effective adsorbent for Cr(VI) removal.

Recent advances in bioremediation of heavy metals and persistent organic pollutants: A review

Heavy metals and persistent organic pollutants are causing detrimental effects on the environment. The seepage of heavy metals through untreated industrial waste destroys the crops and lands. Moreover, incineration and combustion of several products are responsible for primary and secondary emissions of pollutants. This review has gathered the remediation strategies, current bioremediation technologies, and their primary use in both in situ and ex situ methods, followed by a detailed explanation for bioremediation over other techniques. However, an amalgam of bioremediation techniques and nanotechnology could be a breakthrough in cleaning the environment by degrading heavy metals and persistant organic pollutants.

Isotherm, Thermodynamics, and Kinetics of Methyl Orange Adsorption onto Magnetic Resin of Chitosan Microspheres

Severe environmental pollution problems arising from toxic dyestuffs (e.g., methyl orange) are receiving increasing attention. Therefore, dyes' safe removal has become a research hotspot. Among the many physical-chemical removal techniques, adsorption using renewable biological resources has proved to be more advantageous over others due to its effectiveness and economy. Chitosan is a natural, renewable biopolymer obtained by deactivated chitin. Thus, the magnetic resin of chitosan microspheres (MRCM), prepared by reversed-phase suspension cross-linking polymerization, was used to remove methyl orange from a solution in a batch adsorption system. The main results are as follows: (1) The results of physical and swelling properties of MRCM indicated that MRCM was a type of black spherical, porous, water-absorbing, and weak alkali exchange resin, and it had the ability to adsorb methyl orange when it was applied in solutions above pH 2.0. (2) In batch adsorption studies, the maximum adsorption capacity was obtained at pH 5; the adsorption equilibrium time was 140 min; and the maximum adsorption was reached at 450 mg/L initial concentration. (3) Among the three isotherm adsorption models, Langmuir achieved the best fit for the adsorption of methyl orange onto MRCM. (4) The adsorption thermodynamics indicated that the adsorption was spontaneous, with increasing enthalpy, and was driven by the entropy. (5) The pseudo-second-order kinetics equation was most suitable to describe the adsorption kinetics, and the adsorption kinetics was also controlled by the liquid-film diffusion dynamics. Consequently, MRCM with relatively higher methyl orange adsorption exhibited the great efficiency for methyl orange removal as an environment-friendly sorbent. Thus, the findings are useful for methyl orange pollution control in real-life wastewater treatment applications.

Preparation and performance evaluation of chitosan/polyvinylpyrrolidone/polyvinyl alcohol electrospun nanofiber membrane for heavy metal ions and organic pollutants removal

In this work, a novel electrospun chitosan (CS)/polyvinylpyrrolidone (PVP)/polyvinyl alcohol (PVA) nanofibrous membrane was prepared to remove heavy metal ions and organic pollutants from water. The nanofiber morphologies were adjusted through the optimal electrospinning process parameters. Fourier-transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM) characterizations indicated that a well-crosslinked CS/PVP/PVA nanofiber film was formed. Under the optimize conditions, the obtained CS/PVP/PVA nanofiber membranes exhibited porous and uniform nanofibrous structures with an average diameter of 160 nm and a pure water permeability of 4518.91 L·m^-2·h^-1·bar^-1. In addition, the adsorption and separation performance of CS/PVP/PVA nanofiber membranes were evaluated with Cu(II), Ni(II), Cd(II), Pb(II) and Methylene Blue (MB), Malachite Green (MG) as target ions and dyes. The results showed that the retention rate of CS/PVP/PVA nanofiber membranes for Cu(II), Ni(II), Cd(II), Pb(II), MG and MB can reach 94.20%, 90.35%, 83.33%, 80.12%, 84.01% and 69.91%, respectively. The adsorption capacities of Cu(II), Ni(II), Cd(II), Pb(II), MG and MB were 34.79, 25.24, 18.07, 16.05, 17.86 and 13.27 mg g^-1. The adsorption kinetics of heavy metal ions and dyes by the nanofiber membranes can be explained by the Langmuir isotherm model and represented by the pseudo-second-order kinetic mechanism that determined the spontaneous chemisorption process. This study provides a synthetic approach to membranes for the removal of organic and heavy metal micropollutants from water.

Integrated approaches to mitigate threats from emerging potentially toxic elements: A way forward for sustainable environmental management

Potentially toxic elements (PTEs) such as toxic metal (loid)s and other emerging hazardous contaminants, exist in the environment and poses a serious threat. A large amount of wastewater containing PTEs such as cadmium, chromium, copper, nickel, arsenic, lead, zinc, etc. Release from industries during production process. Besides these, chemical-based fertilizers used in soils during crop production have become one of the crucial sources of PTEs. Various techniques are being employed for the mitigation of PTEs like chemical precipitation, ion exchange, coagulation, activated carbon, adsorption, membrane filtration, and bioremediation. Among these mitigation strategies, biological processes such as bioremediation, phytoremediation etc. Are extensively used, as they are economic have high-efficiency rate and are eco-friendly. This review intends to provide information on PTEs contamination through various sources; along with the toxicity of metal (loid)s with respect to their patterns of transmission and risks in the changing environment. Various remediation methods for the management of these pollutants along with their techno-economic perspective are also summarized in this review.

Research progress in the removal of heavy metals by modified chitosan

Chitosan and its modifiers have been widely studied for their good biocompatibility and excellent adsorption properties for heavy metal ions. The synthesis and application of modified chitosan, the effects of process variables (such as pH, amount of adsorbent, temperature, contact time, etc.), adsorption kinetics, thermodynamics and the adsorption mechanism on the removal of heavy metal ions are reviewed. The purpose is to provide the latest information about chitosan as adsorbent and to promote the synthesis of modified chitosan and its application in the removal of heavy metals.

Water treatment using stimuli-responsive polymers

Stimuli-responsive polymers are a new category of smart materials used in water treatment via a stimuli-induced purification process and subsequent regeneration processes.

Recent progress, synthesis, and applications of chitosan-decorated magnetic nanocomposites in remediation of dye-laden wastewaters

Over the past several decades, the disposal of dyes from the industrial manufacturing sector has had an inadvertent impact on water ecology as polluted water bodies with these hazardous dyes...

Fly ash modified magnetic chitosan-polyvinyl alcohol blend for reactive orange 16 dye removal: Adsorption parametric optimization

A magnetic biocomposite blend of chitosan-polyvinyl alcohol/fly ash (m-Cs-PVA/FA) was developed by adding fly ash (FA) microparticles into the polymeric matrix of magnetic chitosan-polyvinyl alcohol (m-Cs-PVA). The effectiveness of m-Cs-PVA/FA as an adsorbent to remove textile dye (reactive orange 16, RO16) from aquatic environment was evaluated. The optimum adsorption key parameters and their significant interactions were determined by Box-Behnken Design (BBD). The analysis of variance (ANOVA) indicates the significant interactions can be observed between m-Cs-PVA/FA dose with solution pH, and m-Cs-PVA/FA dose with working temperature. Considering these significant interactions, the highest removal of RO16 (%) was found 90.3% at m-Cs-PVA/FA dose (0.06 g), solution pH (4), working temperature (30 °C), and contact time (17.5 min). The results of adsorption kinetics revealed that the RO16 adsorption was better described by the pseudo-second-order model. The results of adsorption isotherm indicated a multilayer adsorption process as well described by Freundlich model with maximum adsorption capacity of 123.8 mg/g at 30 °C. An external magnetic field can be easily applied to recover the adsorbent (m-Cs-PVA/FA). The results supported that the synthesized m-Cs-PVA/FA presents itself as an effective and promising adsorbent for textile dye with preferable adsorption capacity and separation ability during and after the adsorption process.

Emerging novel polymeric adsorbents for removing dyes from wastewater: A comprehensive review and comparison with other adsorbents

Dye molecules are one of the most hazardous compounds for human and animal health and the excess intake of these materials can create toxic impacts. Several studies show the practicality of the adsorption process for dye uptake from wastewaters. In recent years, various adsorbents were used to be efficient in this process. Among all, polymeric adsorbents demonstrate great applicability in different environmental conditions and attract many researchers to work on them, although there is not enough reliable and precise information regarding these adsorbents. This study aims to investigate some influential parameters such as their type, physical properties, experimental conditions, their capacity, and further modeling along with a comparison with non-polymeric adsorbents. The influence of the main factors of adsorption capacity was studied and the dominant mechanism is explained extensively.

Fabrication of a CO2-responsive chitosan aerogel as an effective adsorbent for the adsorption and desorption of heavy metal ions

In the traditional desorption method, strong acid is commonly used as an eluent for the regeneration of adsorbents. It is of critical economic and environmental significance to develop a chemical-free desorption method. In this study, a new CO₂-responsive chitosan aerogel adsorbent was synthesized from CO₂-responsive poly(acrylic acid-2-(dimethylamino)ethyl methacrylate) and chitosan by physicochemical double crosslinking for the adsorption of Cu²⁺. Compared with the chitosan aerogel, the adsorption capacity of Cu²⁺ and mechanical properties of CO₂-responsive chitosan aerogel increased by 162% and 660%, respectively. Most importantly, after the adsorption of Cu²⁺ by CO₂-responsive chitosan aerogel, the Cu²⁺ could be desorbed by CO₂ bubbling, and the desorption rate of metal ions was more than 80%. The adsorption of Cu²⁺ by aerogel was attributed to chelation and complexation. The desorption of porous chitosan/P(AA-co-DMAEMA) aerogels (CPA) by CO₂ mainly occurred through charge repulsion of protonated ‒NH₂ and ‒N‒ groups. After 6 cycles, the adsorption capacity of CPA for metal ions still reached 70% of the initial adsorption capacity, and the desorption rate reached 75%. This novel CO₂-responsive chitosan aerogel is a highly efficient and environmentally friendly adsorbent for the adsorption and recovery of metal ions.

Enhanced Performance of Chitosan via a Novel Quaternary Magnetic Nanocomposite Chitosan/Grafted Halloysitenanotubes@ZnγFe3O4 for Uptake of Cr (III), Fe (III), and Mn (II) from Wastewater

A novel chitosan/grafted halloysitenanotubes@Znγmagnetite quaternary nanocomposite (Ch/g-HNTs@ZnγM) was fabricated using the chemical co-precipitation method to remove the ions of Cr (III), Fe (III), and Mn (II) from wastewater. The characteristics of the synthesized Ch/g-HNTs@ZnγM quaternary nanocomposite were investigated using FTIR, SEM, XRD, GPC, TGA, TEM, and surface zeta potential. The characterization analysis proved that the mentioned nanocomposite structure contains multiple functional groups with variable efficiencies. Additionally, they proved the existence of magnetic iron in the nanocomposite internal structure with the clarity of presentation of gaps and holes of high electron density on its surface. The results showed that the pH and time to reach an equilibrium system for all the studied metal ions were obtained at 9.0 and 60 min, respectively. The synthesized Ch/g-HNTs@ZnγM nanocomposite exhibited maximum adsorption removal of 95.2%, 99.06%, and 87.1% for Cr (III), Fe (III), and Mn (II) ions, respectively. The pseudo-second-order kinetic model and, for isotherm, the Langmuir model were best fitted with the experimental data. The thermodynamic parameters indicated the exothermic and spontaneous nature of the adsorption reaction as proven by the ΔH° and ΔG° values. Additionally, chemical adsorption by the coordination bond is supposed as the main mechanism of adsorption of the mentioned metal ions on the nanocomposite. Finally, Ch/g-HNTs@ZnγM displays prospected advantages, such as a low-expense adsorbent, high efficiency and availability, and an eco-friendly source, that will reduce the environmental load via an environmentally friendly method.

Preparation and adsorption properties of Ni(ii) ion-imprinted polymers based on synthesized novel functional monomer

In this study, a novel functional monomer N-(1-(2,4-difluorophenyl)-2-(1H-1,2,4-triazol-1-yl)ethyl)acrylamide (NDTEA) was designed and synthesized, and was used to prepare Ni(ii) ion-imprinted polymers (Ni(ii)-IIPs). Sixteen kinds of Ni(ii)-IIP (Ni(ii)-IIP1–16) and corresponding non-imprinted polymers (NIP1–16) were prepared by precipitation polymerization method. After optimized condition experiment, Ni(ii)-IIP5 possessed maximum adsorption capacity and better imprinting factor under optimal experimental conditions which indicated by equilibrium adsorption experiments. The morphology and structural characteristics of Ni(ii)-IIP5 were characterized by scanning electron microscopy (SEM) and Brunauer–Emmett–Teller (BET). The adsorption selectivity of Ni(ii)-IIP5 was analyzed by ICP-OES, and the results showed that Ni(ii)-IIP5 had favorable selectivity recognition ability for Ni(ii) when Cu(ii), Co(ii), and Cd(ii) are used as competitive ions. The kinetic experiment indicated that the performance of Ni(ii) adsorption on the surface of Ni(ii)-IIP5 obeyed the pseudo-first-order model, and adsorption equilibrium was attained after 15 min. Isothermal adsorption process fitted to Langmuir and Freundlich isothermal adsorption models, simultaneously. The results showed that Ni(ii)-IIP5 prepared by using a new functional monomer had better permeation selectivity and higher affinity for Ni(ii), which also verified the rationality of the functional monomer design. At the same time, it also provided a broad application prospect for removal of Ni(ii) in complex samples.