Engineering the nanoarchitecture and texture of polymeric carbon nitride semiconductor for enhanced visible light photocatalytic activity

A novel g-C3N4-SH@konjac glucomannan composite aerogel for patulin removal from apple juice and its photocatalytic regeneration

Patulin (PAT) is a hazardous mycotoxin frequently occurs in fruit industry. A reusable g-C3N4-SH@KG composite aerogel for PAT removal in a novel "dark adsorption-light regeneration" mode was prepared by thiol(-SH) functionalization and konjac glucomannan (KG) immobilization. The g-C3N4-SH@KG was characterized by SEM, FT-IR, XPS and UV-Vis DRS, and its PAT adsorption and photocatalytic regeneration behaviors and mechanisms were investigated. The g-C3N4-SH@KG exhibited good regeneration performance, maintaining 83% of PAT initial adsorption capacity (0.92 mg/g) after 5 "adsorption-regeneration" cycles. The adsorption process was endothermic and spontaneous. •OH and h+ generated by photocatalysis were the main substances that degraded PAT into two products and regenerated -SH. The g-C3N4-SH@KG could effectively remove PAT without negative impact on juice quality. The study provided a new strategy for the regeneration of thiol-functionalized PAT adsorbents, and a new idea for the application of non-selective photocatalysis in the control of food contaminations.

Urea-driven g-C3N4 nanostructures for highly efficient photoreduction of Cr(vi) under visible LED light: effects of calcination temperature

Graphitic carbon nitride (g-C3N4) nanostructures were synthesized via the calcination of urea at various temperatures ranging between 400 and 600 °C and were utilized for photoreduction of Cr(vi) in aqueous medium. Due to the low adsorption of Cr(vi) on the g-C3N4 surface, a more accurate assessment of the photocatalytic performance of the samples was carried out. Although the characterization showed that the specific surface of samples increased as the calcination temperature increased, the most efficient product in terms of the photoreduction duration of Cr(vi) was produced through the calcination process carried out at 450 °C, which reduced the concentration by more than 99% in 40 minutes. These results demonstrate that the structural and surface properties of g-C3N4 are critical factors that impact the photocatalytic performance. Alongside the calcination temperatures, the concentration of citric acid as a hole scavenger, the source of illumination, pH levels, and the recycling ability of the produced specimen at 450 °C were also investigated. Conspicuously, the photocatalyst works better when more citric acid is present and the pH level decreases. Out of all the cases studied regarding the light source, the 400 nm LED light source was found to be the most efficient. Additionally, even after going through the photoreduction process four times, the photocatalyst still remained highly efficient.

Boosting the Activation of Molecular Oxygen and the Degradation of Rhodamine B in Polar-Functional-Group-Modified g-C3N4

Molecular oxygen activation often suffers from high energy consumption and low efficiency. Developing eco-friendly and effective photocatalysts remains a key challenge for advancing green molecular oxygen activation. Herein, graphitic carbon nitride (g-C3N4) with abundant hydroxyl groups (HCN) was synthesized to investigate the relationship between these polar groups and molecular oxygen activation. The advantage of the hydroxyl group modification of g-C3N4 included narrower interlayer distances, a larger specific surface area and improved hydrophilicity. Various photoelectronic measurements revealed that the introduced hydroxyl groups reduced the charge transfer resistance of HCN, resulting in accelerated charge separation and migration kinetics. Therefore, the optimal HCN-90 showed the highest activity for Rhodamine B photodegradation with a reaction time of 30 min and an apparent rate constant of 0.125 min-1, surpassing most other g-C3N4 composites. This enhanced activity was attributed to the adjusted band structure achieved through polar functional group modification. The modification of polar functional groups could alter the energy band structure of photocatalysts, narrow band gap, enhance visible-light absorption, and improve photogenerated carrier separation efficiency. This work highlights the significant potential of polar functional groups in tuning the structure of g-C3N4 to enhance efficient molecular oxygen activation.

High-Efficiency Photo-Fenton-like Catalyst of FeOOH/g-C3N4 for the Degradation of PNP: Characterization, Catalytic Performance and Mechanism Exploration

The composite photocatalyst FeOOH/g-C3N4 was prepared through thermal polycondensation and co-precipitation methods, followed by XRD, SEM and UV-vis characterization. The stability of FeOOH/g-C3N4 was explored by the recycling test. The active species in the reaction system were investigated by the capture experiment. The results indicated that the optimal preparation condition for g-C3N4 involved calcination at 600 °C for 4 h. XRD analysis revealed that g-C3N4 exhibits a high-purity phase, and Fe in FeOOH/g-C3N4 exists in a highly dispersed amorphous state. SEM analysis showed that FeOOH/g-C3N4 has a rough surface with an irregular layered structure. Element composition analysis confirmed that the content of elements in the prepared catalyst is consistent with the theoretical calculation. FeOOH/g-C3N4 possesses the largest specific surface area of 143.2 m2/g and a suitable pore distribution. UV-vis DRS analysis showed that the absorption intensity of FeOOH/g-C3N4 is stronger than that of g-C3N4. When the catalyst dosage was 1.0 g/L, the H2O2 dosage was 4 mmol/L, the PNP initial concentration was 10 mg/L and the initial pH value was 5, the PNP removal could reach 92% in 120 min. Even after 5 cycles, the efficiency of PNP removal by FeOOH/g-C3N4 remains nearly 80%. The capture experiment indicated that both •OH and •O2- play roles in the photocatalytic degradation of PNP, with •OH being more significant. These findings affirm that FeOOH has been successfully incorporated into g-C3N4, resulting in a conspicuous catalytic effect on the degradation of PNP in the visible light-assisted Fenton-like reaction.

Reusable isotype heterojunction g-C3N4/alginate hydrogel spheres for photocatalytic wastewater treatment

Various visible-light-driven photocatalysts have been studied for practical applications in photocatalytic wastewater treatment via solar irradiation. Among them, g-C3N4 has attractive features, including its metal-free and environmentally friendly nature; however, it is prone to charge recombination and has low photocatalytic activity. To solve these problems, isotype heterojunction g-C3N4 was recently developed; however, the methods employed for synthesis suffered from limited reproducibility and efficiency. In this study, isotype heterojunction g-C3N4 was synthesized from various combinations of precursor materials using a planetary ball mill. The isotype heterojunction g-C3N4 synthesized from urea and thiourea showed the highest photocatalytic activity and completely decolorized Rhodamine B (RhB; 10 ppm) in 15 min under visible-light irradiation. Furthermore, to improve recyclability, isotype heterojunction g-C3N4 was immobilized in alginate hydrogel spheres. The isotype heterojunction g-C3N4/alginate hydrogel beads were used in 10 repeated RhB degradation experiments and were able to maintain their initial photocatalytic activity and mechanical strength. These achievements represent an advance towards practical, sustainable photocatalytic wastewater treatment.

Fenpicoxamid-Imprinted Surface Plasmon Resonance (SPR) Sensor Based on Sulfur-Doped Graphitic Carbon Nitride and Its Application to Rice Samples

This research attempt involved the development and utilization of a newly designed surface plasmon resonance (SPR) sensor which incorporated sulfur-doped graphitic carbon nitride (S-g-C3N4) as the molecular imprinting material. The primary objective was to employ this sensor for the quantitative analysis of Fenpicoxamid (FEN) in rice samples. The synthesis of S-g-C3N4 with excellent purity was achieved using the thermal poly-condensation approach, which adheres to the principles of green chemistry. Afterwards, UV polymerization was utilized to fabricate a surface plasmon resonance (SPR) chip imprinted with FEN, employing S-g-C3N4 as the substrate material. This process involved the inclusion of N,N'-azobisisobutyronitrile (AIBN) as the initiator, ethylene glycol dimethacrylate (EGDMA) as the cross-linker, methacryloylamidoglutamic acid (MAGA) as the monomer, and FEN as the analyte. After successful structural analysis investigations on a surface plasmon resonance (SPR) chip utilizing S-g-C3N4, which was imprinted with FEN, a comprehensive investigation was conducted using spectroscopic, microscopic, and electrochemical techniques. Subsequently, the kinetic analysis applications, namely the determination of the limit of quantification (LOQ) and the limit of detection (LOD), were carried out. For analytical results, the linearity of the FEN-imprinted SPR chip based on S-g-C3N4 was determined as 1.0-10.0 ng L-1 FEN, and LOQ and LOD values were obtained as 1.0 ng L-1 and 0.30 ng L-1, respectively. Finally, the prepared SPR sensor's high selectivity, repeatability, reproducibility, and stability will ensure safe food consumption worldwide.

Fabrication of a Nanosized g-C3N4-Loaded Cellulose Microfiber Bundle to Induce Highly Efficient Water Treatment via Photodegradation

Graphite carbon nitride (g-C3N4) with a suitable structure and strong amine activity is designed and prepared to serve as a hydrogen bond donor for the microfibrilization of corncob cellulose to form a cellulose microfiber (CMF) bundle. Simultaneously, well-dispersed nanosized g-C3N4 is loaded into the bundle to form a photocatalyst for efficient photodegradation of rhodamine B (Rh B) in water. Under the optimal preparation conditions at 165 °C, 10 min, and 0.08 mol/L H2SO4, the yield of g-C3N4-functionalized cellulose microfibers (CMF-g-C3N4) reaches to the highest over 70%. The catalytic rate of CMF-g-C3N4 is 3.3 times larger than that of pure g-C3N4. The degradation rate of Rh B is maintained at over 90% in 10 cycles of photocatalytic degradation. The obtained CMF-g-C3N4 also has good thermal stability and mechanical properties. This research suggests a particularly simple way to transform cellulose into a highly efficient photocatalyst for water treatment.

Facile fabrication of ultra-light N-doped-rGO/g-C3N4 for broadband microwave absorption

"Thin thickness", "lightweight", "wide absorption bandwidth" and "strong absorption" are the new standards of contemporary science and technology for microwave absorption(MA) material. In this study, N-doped-rGO/g-C3N4 MA material was prepared for the first time by simple heat treatment, which the N atoms were doped into rGO and g-C3N4 was dispersed on the surface of N-doped-rGO, and its density is only 0.035 g/cm3. The impedance matching of the N-doped-rGO/g-C3N4 composite was well adjusted by decreasing the dielectric constant and attenuation constant due to the g-C3N4 semiconductor property and the graphite-like structure. Moreover, the distribution of g-C3N4 among N-doped-rGO sheets can produce more polarization effect and relaxation effect by increasing the lamellar spacing. Furthermore, the polarization loss of N-doped-rGO/g-C3N4 could be increased successfully by doping N atoms and g-C3N4. Ultimately, the MA property of N-doped-rGO/g-C3N4 composite was optimized significantly, with a loading of 5 wt%, the N-doped-rGO/g-C3N4 composite exhibited the RLmin of -49.59 dB and the effective absorption bandwidth could reach 4.56 GHz when the thickness was only 1.6 mm. The "thin thickness", "lightweight", "wide absorption bandwidth" and "strong absorption" of MA material are actually achieved by the N-doped-rGO/g-C3N4.

Sunlight active cellulose/g-C3N4/TiO2nano-photocatalyst for simultaneous degradation of methylene blue dye and atenolol drug in real wastewater

The paper critically addresses two contemporary environmental challenges, the water crisis and the unrestricted discharge of organic pollutants in waterways together. An eco-friendly method was used to fabricate a cellulose/g-C3N4/TiO2photocatalytic composite that displayed a remarkable degradation of methylene blue dye and atenolol drug under natural sunlight. Introducing graphitic carbon nitride (g-C3N4) onto pristine TiO2improved hybrid material's photonic efficacy and enhanced interfacial charge separation. Furthermore, immobilizing TiO2/g-C3N4on a semi-interpenetrating cellulose matrix promoted photocatalyst recovery and its reuse, ensuring practical affordability. Under optimized conditions, the nano-photocatalyst exhibited ∼95% degradation of both contaminants within two hours while retaining ∼55% activity after ten cycles demonstrating a promising photostability. The nano-photocatalyst caused 66% and 57% reduction in COD and TOC values in industrial wastewater containing these pollutants. The photocatalysis was fitted to various models to elucidate the degradation kinetics, while LC-MS results suggested the mineralization pathway of dye majorly via ring opening demethylation. >98% disinfection was achieved againstE. coli(104-105CFU·ml-1) contaminated water. This study thus paves multifaceted strategies to treat wastewater contaminants at environmental levels employing nano-photocatalysis.

Graphitic carbon nitride (g-C3N4)-assisted materials for the detection and remediation of hazardous gases and VOCs

Graphitic carbon nitride (g-C3N4)-based materials are attracting attention for their unique properties, such as low-cost, chemical stability, facile synthesis, adjustable electronic structure, and optical properties. These facilitate the use of g-C3N4 to design better photocatalytic and sensing materials. Environmental pollution by hazardous gases and volatile organic compounds (VOCs) can be monitored and controlled using eco-friendly g-C3N4- photocatalysts. Firstly, this review introduces the structure, optical and electronic properties of C3N4 and C3N4 assisted materials, followed by various synthesis strategies. In continuation, binary and ternary nanocomposites of C3N4 with metal oxides, sulfides, noble metals, and graphene are elaborated. g-C3N4/metal oxide composites exhibited better charge separation that leads to enhancement in photocatalytic properties. g-C3N4/noble metal composites possess higher photocatalytic activities due to the surface plasmon effects of metals. Ternary composites by the presence of dual heterojunctions improve properties of g-C3N4 for enhanced photocatalytic application. In the later part, we have summarised the application of g-C3N4 and its assisted materials for sensing toxic gases and VOCs and decontaminating NOx and VOCs by photocatalysis. Composites of g-C3N4 with metal and metal oxide give comparatively better results. This review is expected to bring a new sketch for developing g-C3N4-based photocatalysts and sensors with practical applications.

Photosynthesis of Hydrogen Peroxide Based on g-C3 N4 : The Road of a Cost-Effective Clean Fuel Production

Emerging artificial photosynthesis promises to offer a competitive means for solar energy conversion and further solves the energy crisis facing the world. Hydrogen peroxide (H2 O2 ), which is considered as a benign oxidant and a prospective liquid fuel, has received worldwide attention in the field of artificial photosynthesis on account of the source materials are just oxygen, water, and sunlight. Graphitic carbon nitride (g-C3 N4 )-based photocatalysts for H2 O2 generation have attracted extensive research interest due to the intrinsic properties of g-C3 N4 . In this review, research processes for H2 O2 generation on the basis of g-C3 N4 , including development, fabrication, merits, and disadvantages, and the state-of-the-art methods to enhance the performance are summarized after a brief introduction and the mechanism analysis of an efficient catalytic system. Also, recent applications of g-C3 N4 -based photocatalysts for H2 O2 production are reviewed, and the significance of active sites and synthetic pathways are highlighted from the view of reducing barriers. Finally, this paper ends with some concluding remarks to reveal the issues and opportunities of g-C3 N4 -based photocatalysts for producing H2 O2 in a high yield.

Augmented photocatalytic degradation of Acetaminophen using hydrothermally treated g-C3N4 and persulfate under LED irradiation

Photocatalytic degradation of organic pollutants in water using graphitic carbon nitride and persulfate under visible light (g-C₃N₄/PS system) has been studied. Here, we demonstrate augmentation of photocatalytic degradation of Acetaminophen (AAP) using hydrothermally treated g-C₃N₄ and PS under 400 nm LED irradiation (HT-g-C₃N₄/PS system). A pseudo-first-order rate constant (k_obs, 0.328 min^-1) for degradation of AAP using HT-g-C₃N₄/PS system was determined to be 15 times higher compared to g-C₃N₄/PS system (k_obs, 0.022 min^-1). HT-g-C₃N₄ showed a higher surface area (81 m²/g) than g-C₃N₄ (21 m²/g). Photocurrent response for HT-g-C₃N₄ was higher (1.5 times) than g-C₃N₄. Moreover, Nyquist plot semicircle for HT-g-C₃N₄ was smaller compared to g-C₃N₄. These results confirm effective photoelectron-hole separation and charge-transfer in HT-g-C₃N₄ compared to g-C₃N₄. AAP degradation using HT-g-C₃N₄/PS system was significantly inhibited with O2.- and h⁺ scavengers compared to ¹O_2,SO4.- and HO. scavengers. ESR results revealed O2.- formation in HT-g-C₃N₄/PS system. Moreover, photocurrent measurements reveal AAP oxidation by h⁺ of HT-g-C₃N₄ was effective than g-C₃N₄. HT-g-C₃N₄ was reused for five cycles in HT-g-C₃N₄/PS system. Augmented photocatalytic degradation of AAP by HT-g-C₃N₄/PS system compared to g-C₃N₄/PS is attributed to effective photoelectron hole separation of HT-g-C₃N₄ that generates O2.- and h⁺ for oxidation of pollutant. Importantly, electrical energy per order (E_EO) was 7.2 kWh m^-3 order^-1. k_obs for degradation of AAP in simulated groundwater and tap water were determined as 0.029 and 0.035 min^-1, respectively. Degradation intermediates of AAP were proposed. AAP ecotoxicity against marine bacteria Aliivibrio fischeri was completely removed after treatment by HT-g-C₃N₄/PS system.

Nanocomposites with ZrO2@S-Doped g-C3N4 as an Enhanced Binder-Free Sensor: Synthesis and Characterization

This study describes new electrocatalyst materials that can detect and reduce environmental pollutants. The synthesis and characterization of semiconductor nanocomposites (NCs) made from active ZrO₂@S-doped g-C₃N₄ is presented. Electrochemical impedance spectroscopy (EIS) and Mott-Schottky (M-S) measurements were used to examine electron transfer characteristics of the synthesized samples. Using X-ray diffraction (XRD) and high-resolution scanning electron microscopy (HR-SEM) techniques, inclusion of monoclinic ZrO₂ on flower-shaped S-doped-g-C₃N₄ was visualized. High-resolution X-ray photoelectron spectroscopy (XPS) revealed successful doping of ZrO₂ into the lattice of S-doped g-C₃N₄. The electron transport mechanism between the electrolyte and the fluorine tin-oxide electrode (FTOE) was enhanced by the synergistic interaction between ZrO₂ and S-doped g-C₃N₄ as co-modifiers. Development of a platform with improved conductivity based on an FTOE modified with ZrO₂@S-doped g-C₃N₄ NCs resulted in an ideal platform for the detection of 4-nitrophenol (4-NP) in water. The electrocatalytic activity of the modified electrode was evaluated through determination of 4-NP by cyclic voltammetry (CV) and differential pulse voltammetry (DPV) under optimum conditions (pH 5). ZrO₂@S-doped g-C₃N₄ (20%)/FTOE exhibited good electrocatalytic activity with a linear range from 10 to 100 μM and a low limit of detection (LOD) of 6.65 μM. Typical p-type semiconductor ZrO₂@S-doped g-C₃N₄ NCs significantly impact the superior detection of 4-NP due to its size, shape, optical properties, specific surface area and effective separation of electron-hole pairs. We conclude that the superior electrochemical sensor behavior of the ZrO₂@S-doped g-C₃N₄ (20%)/FTOE surfaces results from the synergistic interaction between S-doped g-C₃N₄ and ZrO₂ surfaces that produce an active NC interface.

Recent Advances in Graphitic Carbon Nitride Based Electro-Catalysts for CO2 Reduction Reactions

The electrocatalytic carbon dioxide reduction reaction is an effective means of combating the greenhouse effect caused by massive carbon dioxide emissions. Carbon nitride in the graphitic phase (g-C₃N₄) has excellent chemical stability and unique structural properties that allow it to be widely used in energy and materials fields. However, due to its relatively low electrical conductivity, to date, little effort has been made to summarize the application of g-C₃N₄ in the electrocatalytic reduction of CO₂. This review focuses on the synthesis and functionalization of g-C₃N₄ and the recent advances of its application as a catalyst and a catalyst support in the electrocatalytic reduction of CO₂. The modification of g-C₃N₄-based catalysts for enhanced CO₂ reduction is critically reviewed. In addition, opportunities for future research on g-C₃N₄-based catalysts for electrocatalytic CO₂ reduction are discussed.

One-step nitrogen defect engineering of polymeric carbon nitride for visible light-driven photocatalytic O2 reduction to H2O2

Polymeric carbon nitride (PCN) is an important metal-free photocatalyst for visible light-driven hydrogen peroxide (H₂O₂) production from O₂ reduction. Herein, we synthesized the DPCN catalysts possessing nitrogen defects by one-step thermal polymerization of urea in N₂ stream. As compared to the PCN conventionally synthesized in static air, X-ray photoelectrons spectroscopy (XPS) characterization disclosed that there are more pyridinic N defects in the DPCN catalysts, which is attributed to the removal of a proportion of NH₃ released from urea pyrolysis by flowing N₂. UV-vis diffuse reflectance spectroscopy (UV-vis DRS), Mott-Schottky, steady-state and time-resolved photoluminescence (PL), and electrochemical impedance spectroscopy (EIS) characterizations revealed that the introduction of the nitrogen defects narrows down the band gap, improves the density of the photoexcited charge carriers, prolongs the lifetime of the charge carriers, and enhances the charge transfer efficiency. In visible light-driven photocatalytic O₂ reduction to H₂O₂, the optimal DPCN catalyst afforded an activity of 4.35 times that of the PCN catalyst and a H₂O₂ concentration of 2.83 mmol L^-1 after 10 h of visible light irradiation. This one-step thermal polymerization approach is valid when replacing N₂ stream with Ar and He streams.

g-C3N4/polyvinyl alcohol-sodium alginate aerogel for removal of typical heterocyclic drugs from water

Heterocyclic drugs (HCDs) detected at high frequencies in wastewater have raised great concerns and their advanced removal has been the hotspot for safe water reuse in recent years. Two-dimensional graphitic carbon nitride (g-C₃N₄) and its photocatalytic systems are increasingly emerging, however, there are inevitable drawbacks of stacking and difficulty in recycling, resulting in decreased pollutant removal and limited application. Herein, for the first time, this paper reported a three-dimensional g-C₃N₄/polyvinyl alcohol-sodium alginate aerogel (g-C₃N₄/PVA-SA aerogel) photocatalyst synthesized by ultrasonic exfoliation and in-situ polymerization for typical HCDs (sulfadiazine (SDZ), sulfamethoxazole (SMX), and carbamazepine (CBZ)) removal in water. The reduced stacking of g-C₃N₄ dispersed in PVA-SA aerogel was achieved as revealed by scanning electron microscopy (SEM) and X-ray diffractometer (XRD) analysis, and g-C₃N₄/PVA-SA aerogel was observed to possess encouraging degradation efficiencies and rates for SDZ (100%, 0.0249 min^-1), SMX (100%, 0.1762 min^-1) and CBZ (69.8%, 0.0056 min^-1), which were improved by 50%-60% and 133%-216% compared to those of g-C₃N₄, respectively. Meanwhile, environmental impact factors such as pH and coexisting ions had less impact on the degradation of SDZ and SMX by g-C₃N₄/PVA-SA aerogel. The novel aerogel also had a good recyclability, with less than 5% reduction in degradation efficiency after five cycles observed. The photodegradation of SDZ, SMX and CBZ was confirmed to be driven by ⋅O₂^- and h⁺ through scavenger-quenching experiments. The new low carbon and recyclable g-C₃N₄/PVA-SA aerogel reported in this study indicated a good potential for efficient removal of HCDs from water, which provides an alternative strategy for advanced purification and safe reuse of wastewater.

The effect of N-vacancy on the photocatalytic activity of graphitic carbon nitride in the oxidative Mannich reaction

N-vacancy g-CN was used in Mannich oxidative reaction as a photocatalyst, having mid-gap states that enhance reaction kinetics. This facile photocatalyst enabled successful formation of challenging THIQ with EWG and chemo-selectivity on C–C bond.

Synthesis and photocatalytic performance of g-C3N4/MeTMC-COP composite photocatalyst

Covalent organic polymers have excellent application prospects in photocatalysis due to their excellent visible light absorption and structural designability. However, their fast recombination efficiency and complex preparation process limit their applications. Because of the above problems, this paper used urea to prepare g-C₃N₄ by high-temperature thermal polymerization and prepared g-C₃N₄ composite photocatalyst loaded with MeTMC-COP (g-C₃N₄/MeTMC-COP) by hydrothermal method. The photocatalytic hydrogen generation and photocatalytic degradation capabilities of composite photocatalysts with various mass ratios were investigated by characterizing the catalyst and using the organic dye Rhodamine B (RhB) as the pollutant. According to the research, the specific surface area of the g-C₃N₄/MeTMC-COP composite may reach 40.95 m² g^-1 when the mass ratio of g-C₃N₄ and MeTMC-COP is 3:1 (25.22 m² g^-1). It can offer more active sites for the photocatalytic process, and because the fluorescence peak intensity is the lowest, it has the lowest photogenerated electron-hole recombination efficiency. In comparison to g-C₃N₄, 3:1 g-C₃N₄/MeTMC-COP can breakdown rhodamine B up to 100% after 75 min of light irradiation; its photocatalytic hydrogen generation efficiency is 1.62 times that of g-C₃N₄, and the hydrogen evolution rate is 11.8 μmol g^-1 h^-1.

Ultrasonic-assisted synthesis of porous S-doped carbon nitride ribbons for photocatalytic reduction of CO2

A series of porous S-doped carbon nitride ribbons (PSCN) were prepared by one-pot hydrothermal and sonochemical synthesis techniques. The morphologies and nanostructures of the catalysts were characterized by SEM, XRD and IR, which confirmed the pristine graphitic structures of carbon nitrides retained in the products. Due to sonication treatment, PSCN has porous structures in the thin ribbon and larger specific surface areas (PSCN 43.5 m²/g, SCN 26.6 m²/g and GCN 6.5 m²/g). XPS and elemental mappings verified that sulfur atoms were successfully introduced into the carbon nitride framework. Diffuse reflectance spectroscopy (DRS) results showed S-doping in the carbon nitride reduced the bandgap energy and enhanced their capability of the utilization of visible light, which contributed to higher photo-generated current. Photoluminescence (PL) analysis indicates the recombination of photogenerated carriers was suppressed in PSCN. Moreover, the photocatalytic performance showed that S-doping and porous and thin ribbon nanostructures may effectively boost the CO₂ reduction rate (to as much as 5.8 times of GCN) when illuminated byvisible light (>420 nm) without the need of sacrificial materials. The preliminary mechanisms of the formation of PSCN and its applications in photocatalytic CO₂ reduction are proposed. It highlights the potential of the current technique to produce effective, nonmetal-doped carbon nitride photocatalysts.

Simple one-pot, high-yield synthesis of 2D graphitic carbon nitride nanosheets for photocatalytic hydrogen production

2-Dimensional (2D) graphitic carbon nitrate (g-C₃N₄) nanosheets are particularly interesting photocatalytic materials because of their large surface area and excellent photoelectric properties. However, it remains challenging to synthesize 2D g-C₃N₄ nanosheets with high yield and high activity simultaneously. In this work, a urea-assisted one-pot method was developed in which the decomposition of urea released NH₃ gas which exfoliated bulk g-C₃N₄ into thin nanosheets and generated pores and wrinkles on their surface. The product g-C₃N₄ nanosheets therefore possessed abundant surface active sites for interaction with reactants and showed enhanced light utilization efficiency, giving rise to their improved hydrogen production activity which was 3.36 times higher than that of their bulk counterpart. Importantly, the yield of g-C₃N₄ nanosheets using this method was almost doubled compared to a previously reported ammonium chloride (NH₄Cl) assisted method. Given that g-C₃N₄ nanosheets are building blocks for various photocatalysts, the current synthetic method which produces g-C₃N₄ nanosheets with high yield and high activity shall pave the way for high-performance photocatalytic applications such as hydrogen production and more.

Recent advancement in conjugated polymers based photocatalytic technology for air pollutants abatement: Cases of CO2, NOx, and VOCs

According to World Health Organization (WHO) survey, air pollution has become the major reason of several fatal diseases, which had led to the death of 7 million peoples around the globe. The 9 people out of 10 breathe air, which exceeds WHO recommendations. Several strategies are in practice to reduce the emission of pollutants into the air, and also strict industrial, scientific, and health recommendations to use sustainable green technologies to reduce the emission of contaminants into the air. Photocatalysis technology recently has been raised as a green technology to be in practice towards the removal of air pollutants. The scientific community has passed a long pathway to develop such technology from the material, and reactor points of view. Many classes of photoactive materials have been suggested to achieve such a target. In this context, the contribution of conjugated polymers (CPs), and their modification with some common inorganic semiconductors as novel photocatalysts, has never been addressed in literature till now for said application, and is critically evaluated in this review. As we know that CPs have unique characteristics compared to inorganic semiconductors, because of their conductivity, excellent light response, good sorption ability, better redox charge generation, and separation along with a delocalized π-electrons system. The advances in photocatalytic removal/reduction of three primary air-polluting compounds such as CO₂, NO_X, and VOCs using CPs based photocatalysts are discussed in detail. Furthermore, the synergetic effects, obtained in CPs after combining with inorganic semiconductors are also comprehensively summarized in this review. However, such a combined system, on to better charges generation and separation, may make the Adsorb & Shuttle process into action, wherein, CPs may play the sorbing area. And, we hope that, the critical discussion on the further enhancement of photoactivity and future recommendations will open the doors for up-to-date technology transfer in modern research.

The g-C3N4@CdO/ZnO ternary composite: photocatalysis, thermodynamics and acute toxicity studies

Binary and ternary nanocomposites (NCs) were synthesized by precipitation and through facile one-pot ultrasonic assisted methods to serve as photocatalysts for treatment of wastewater as well as their toxicity toward aquatic organism (Nile tilapia). The crystalline structure, band gap energy and functional groups of these materials were characterized by XRD, UV-Vis, and FT-IR instrumental techniques. Based on the UV-Vis study, the band gap of ZnO/CdO (ZC) to hybrid g-C₃N₄@ZnO/CdO (GZC) nanocomposite was reduced from 3.41 eV to 3.21 eV, suggesting good charge carrier mobility. Photocatalytic degradation performances of ZC and GZC were further assessed by conducting methyl red (MR) photodegradation reaction using UV light. The highest degradation efficiency was achieved for GZC NCs (97.78%) than ZC (89.41%) in 2 h. The values of free energy, and enthalpy were negative; showing spontaneous photodegradation of MR. The kinetics of photodegradation follows pseudo-first-order reaction with rate order of 0.0713 min⁻¹. The HO∗ and O₂∗ were main active species for the photodegradation of MR. The toxicity of NCs calculated and the lethal concentration (LC₅₀) was 113 ppm after 12 h.

Synthesis and characterization of CuO@S-doped g-C3N4 based nanocomposites for binder-free sensor applications

This study presents the simultaneous exfoliation and modification of heterostructured copper oxide incorporated sulfur doped graphitic carbon nitride (CuO@S-doped g-C₃N₄) nanocomposites (NCs) synthesized via chemical precipitation and pyrolysis techniques. The results revealed that the approach is feasible and highly efficient in producing 2-dimensional CuO@S-doped g-C₃N₄ NCs. The findings also showed a promising technique for enhancing the optical and electrical properties of bulk g-C₃N₄ by combining CuO nanoparticles (NPs) with S-doped g-C₃N₄. The crystallite and the average size of the NCs were validated using X-ray diffraction (XRD) studies. Incorporation of the cubical structured CuO on flower shaped S-doped-g-C₃N₄ was visualized and characterized through XRD, HR-SEM/EDS/SED, FT-IR, BET, UV-Vis/DRS, PL, XPS and impedance spectroscopy. The agglomerated NCs had various pore sizes, shapes and nanosized crystals, while being photo-active in the UV-vis range. The synergistic effect of CuO and S-doped g-C₃N₄ as co-modifiers greatly facilitates the electron transfer process between the electrolyte and the bare glassy carbon electrode. Specific surface areas of the NCs clearly revealed modification of bulk S-doped g-C₃N₄ when CuO NPs are incorporated with S-doped g-C₃N₄, providing a suitable environment for the binder-free decorated electrode with sensing behavior for hazardous pollutants. This was tested for the preparation of a 4-nitrophenol sensor.

Template-based textural modifications of polymeric graphitic carbon nitrides towards waste water treatment

The composite materials based on graphitic carbon nitrides (g-C₃N₄) are remarkably better semiconductors, but the inherent photocatalytic performance in its generic synthesis form is not up to the mark. Eminence efforts have been made to improve its performance and photocatalytic efficiencies. Recently, extensive investigations have been performed to develop their texturally modified and highly porous structures to get around the big flaws of bulk g-C₃N₄. One significant disadvantage is the increase in the polycondensation while preparation at 550 °C results in g-C₃N₄ materials with restricted specific surface area (SSA) (<10 m²/g) and no textured pores. Textural modification has emerged as an efficient and progressive way to improve optical and electronic characteristics. The final texture and shape of CN are influenced by the precursor's interaction with the template. Researchers are interested in developing CN materials with high SSA and changeable textural properties (pore volume and pore size). Based on the literature review it is concluded that the soft templating approach is relatively simple, and straightforward to induce textural changes in the g-CN type materials. This review focused on improving the textural properties of bulk g-C₃N₄ via templating method, and the major advances in the modified g-C₃N₄ materials for the treatment of wastewater. The procedures and mechanisms of numerous approaches with varying morphologies are thoroughly explained.

Two-dimensional layered carbon-based catalytic ozonation for water purification: Rational design of catalysts and an in-depth understanding of the interfacial reaction mechanism

This review renewed insight into the existing complex and contradictory mechanisms of catalytic ozonation by two-dimensional layered carbon-based materials (2D-LCMs) for degradation toxic refractory organics in aqueous solution. Migration and capture of active electrons are central to catalytic ozonation reactions, which was not studied or reviewed more clearly. Based on this perspective, the catalytic ozonation potential of 2D-LCMs synthesized by numerous methods is firstly contrasted to guide the design of subsequent carbon based-catalysts, and not limited to 2D-LCMs. Matching ROS to active sites is a key step in understanding the catalytic mechanism. The structure-activity relationships between reported numerous active sites and ROS evolution is then constructed. Result showed that OH could be produced by -OH, -C=O, -COOH groups, defective sites, immobilized metal atoms, doped heteroatoms and photo-induced electrons; and O₂^- could be produced by -OH groups and sp²-bonded carbon. The normalized model further be used to visually compare the contribution degree of various regulatory methods to performance improvement. More importantly, this review calls for 2D-LCMs-based catalytic ozonation to be studied without circumventing the issue of structural stability, which would lead to many proposals of catalysts and its involved catalytic reaction mechanism being meaningless.

Recent advances in visible-light graphitic carbon nitride (g-C3N4) photocatalysts for chemical transformations

Graphitic carbon nitride (g-C3N4) has emerged as a new research hotspot, attracting broad interdisciplinary attention in the form of metal-free and visible-light-responsive photocatalysts in the field of solar energy conversion and environmental remediation. These photocatalysts have evolved as attractive candidates due to their non-toxicity, chemical stability, efficient light absorption capacity in the visible and near-infrared regions, and adaptability as a platform for the fabrication of hybrid materials. This review mainly describes the latest advances in g-C3N4 photocatalysts for chemical transformations. In addition, the typical applications of g-C3N4-based photocatalysts involving organic transformation reactions are discussed (synthesis of heterocycles, hydrosulfonylation, hydration, oxygenation, arylation, coupling reactions, etc.).

Photocatalytic hydrogen evolution based on carbon nitride and organic semiconductors

Photocatalytic hydrogen evolution (PHE) presents a promising way to solve the global energy crisis. Metal-free carbon nitride (CN) and organic semiconductors photocatalysts have drawn intense interests due to their fascinating properties such as tunable molecular structure, electronic states, strong visible-light absorption, low-cost etc. In this paper, the recent progresses of photocatalytic hydrogen production based on organic photocatalysts, including CN, linear polymers, conjugated porous polymers and small molecules, are reviewed, with emphasis on the various strategies to improve PHE efficiency. Finally, the possible future research trends in the organic photocatalysts are prospected.

Emerging Layered Materials and Their Applications in the Corrosion Protection of Metals and Alloys

Metals and alloys are essential in modern society, and are used in our daily activities. However, they are prone to corrosion, with the conversion of the metal/alloy to its more thermodynamically-favored oxide/hydroxide phase. These undesirable corrosion reactions can lead to the failure of metallic components. Consequently, corrosion-protective technologies are now more important than ever, as it is essential to reduce the waste of valuable resources. In this review, we consider the role of emerging 2D materials and layered materials in the development of a corrosion protection strategy. In particular, we focus on the materials beyond graphene, and consider the role of transition metal dichalcogenides, such as MoS2, MXenes, layered double hydroxides, hexagonal boron nitride and graphitic carbon nitride in the formulation of effective and protective films and coatings. Following a short introduction to the synthesis and exfoliation of the layered materials, their role in corrosion protection is described and discussed. Finally, we discuss the future applications of these 2D materials in corrosion protection.

The Influence of Metal-Doped Graphitic Carbon Nitride on Photocatalytic Conversion of Acetic Acid to Carbon Dioxide

Metal-doped graphitic carbon nitride (MCN) materials have shown great promise as effective photocatalysts for the conversion of acetic acid to carbon dioxide under UV–visible irradiation and are superior to pristine carbon nitride (g-C₃N₄, CN). In this study, the effects of metal dopants on the physicochemical properties of metal-doped CN samples (Fe-, Cu-, Zn-, FeCu-, FeZn-, and CuZn-doped CN) and their catalytic activity in the photooxidation of acetic acid were investigated and discussed for their correlation, especially on their surface and bulk structures. The materials in the order of highest to lowest photocatalytic activity are FeZn_CN, FeCu_CN, Fe_CN, and Cu_CN (rates of CO₂ evolution higher than for CN), followed by Zn_CN, CuZn_CN, and CN (rates of CO₂ evolution lower than CN). Although Fe doping resulted in the extension of the light absorption range, incorporation of metals did not significantly alter the crystalline phase, morphology, and specific surface area of the CN materials. However, the extension of light absorption into the visible region on Fe doping did not provide a suitable explanation for the increase in photocatalytic efficiency. To further understand this issue, the materials were analyzed using two complementary techniques, reversed double-beam photoacoustic spectroscopy (RDB-PAS) and electron spin resonance spectroscopy (ESR). The FeZn_CN, with the highest electron trap density between 2.95 and 3.00 eV, afforded the highest rate of CO₂ evolution from acetic acid photodecomposition. All Fe-incorporated CN materials and Cu-CN reported herein can be categorized as high activity catalysts according to the rates of CO₂ evolution obtained, higher than 0.15 μmol/min⁻¹, or >1.5 times higher than that of pristine CN. Results from this research are suggestive of a correlation between the rate of CO₂ evolution via photocatalytic oxidation of acetic acid with the threshold number of free unpaired electrons in CN-based materials and high electron trap density (between 2.95 and 3.00 eV).

Enhanced adsorption of humic/fulvic acids onto urea-derived graphitic carbon nitride

Since humic substances (HSs) can cause environmental problems, their elimination has been attracting more and more concerns. In this study, we investigated HSs adsorption onto urea-derived graphitic carbon nitride (CNU) and elucidated adsorption mechanisms (i.e. heterogeneity, interface rearrangement, and multiple interactions). The adsorption capacity of CNUs was enhanced as increasing calcination temperature and time. Among CNUs, CNU-575-3 showed the highest adsorption capacity; the maximum adsorption capacities for humic acid (HA) and fulvic acid (FA) were 164.06 mg C/g, 14.61 L/cm·g, 91.12 mg C/g, and 5.34 L/cm·g, respectively. The adsorption affinity of CNUs mainly correlated with the amount of amino groups, and that of HSs components was dependent on aromaticity due to π-π interactions. More specifically, terrestrial humic-like and fulvic-like components within HA and FA showed the greatest adsorption affinity, respectively. HSs adsorption was remarkably affected by pH, alkali metals, and alkali earth metals via electrostatic interactions, H-bonding, cation bridge, and configurational effect. In addition, the adsorption of Elliott soil HA (ESHA) and the landfill leachate concentrate by CNUs was also highly efficient. This study shows the great promise of CNUs for HSs adsorption in waters and wastewaters.

Catalytic wet air oxidation of toxic containments over highly dispersed Cu(II)/Cu(I)-N species in the framework of g-C3N4

Catalytic wet air oxidation (CWAO) is a harmless, cheap and effective technology for the degradation of toxic containments directly to CO₂ and H₂O. In this work, highly dispersed Cu(II)/Cu(I)-N that embedded in the framework of g-C₃N₄ (Cu_x-g-C₃N₄) were synthesized in a facile thermal polymerization method and used in the CWAO of phenols, antibiotics and vitamins. Characterization results confirmed that g-C₃N₄ formed in the prepared catalyst and copper was chemically coordinated with N in g-C₃N₄, which inhibited the aggregation of copper. Meanwhile, Cu(II) or Cu(I) in the framework of g-C₃N₄ was more effective for the degradation of phenol than Cu(0) and CuO, and more than 23 toxic containments could be degraded under mild conditions. The prominent performance of Cu_0.1-g-C₃N₄ for CWAO reaction was discussed on the base of these experiments and it was disclosed that in-situ formed H₂O₂ might be contributed to the highly activity.

Development of a metal-free black phosphorus/graphitic carbon nitride heterostructure for visible-light-driven degradation of indomethacin

The development of affordable and efficient technologies for the removal of pharmaceuticals and personal care products (PPCPs) from water has recently been the subject of extensive attention. In this study, a black phosphorus/graphitic carbon nitride (BP-g-C₃N₄) heterostructure is fabricated as an extremely active metal-free photocatalyst via a newly-developed exfoliation strategy. The BP-g-C₃N₄ shows an 11 times better decomposition rate of a representative PPCPs-type pollutant, indomethacin (IDM), compared to the widely-used P25 TiO₂ under real-sunlight illumination. Also, its visible-light activity is even better than that of the best photocatalysts previously developed, but only consumes 1/10-1/4 of the catalyst. The results show that BP performs a cocatalyst-like behavior to catalyze the generation of reactive oxygen species, thus speeding up the decomposition of IDM. In addition, the BP-g-C₃N₄ photocatalyst also exhibits excellent IDM removal efficiency in authentic water matrices (tap water, surface water, and secondarily treated sewage effluent). Large-scale application demonstration under natural sunlight further reveals the practicality of BP-g-C₃N₄ for real-world water treatment operations. Our work will open up new possibilities in the development of purely metal-free photocatalysts for "green" environmental remediation applications.

Synergism between few-layer black phosphorus and graphitic carbon nitride enhances the photoredox C–H arylation under visible light irradiation

A volcano-shaped relation between the amount of FLBP in the FLBP/g-CN heterojunctions in the photoredox C–H arylation was exhibited. To understand the activity of 35 wt% FLBP/g-CN, band alignments of heterojunction was studied in detailed.