Lead removal from aqueous solutions by raw sawdust and magnesium pretreated biochar: Experimental investigations and numerical modelling

Study on the removal efficacy and mechanism of phosphorus from wastewater by eggshell-modified biochar

The excessive discharge of phosphorus from rural domestic sewage is a problem that worthy of attention. If the phosphorus in the sewage were recovered, addressing this issue could significantly contribute to mitigating the global phosphorus crisis. In this study, corn straw, a common agricultural waste, was co-pyrolytically modified with eggshells, a type of food waste from university cafeterias. The resulting product, referred to as corn straw eggshell biochar (EGBC) was characterized using SEM, XRD, XPS, XRF, and other methods. Batch adsorption experiments were conducted to determine the optimal preparation conditions of EGBC and to explore its adsorption characteristics. EGBC showed strong adsorption effectiveness within a pH range of 5-12. The adsorption isotherm closely followed the Sips model (R2  > 0.9011), and the adsorption kinetics were more consistent with the pseudo-second-order model (R2  > 0.9899). The process was found to be both spontaneous and endothermic. Under optimal conditions, the phosphorus adsorption capacity of EGBC was measured to be 288.83 mg/g. This demonstrates the high efficiency of EGBC for phosphorus removal and illustrates an effective method of utilizing food waste for environmental remediation. PRACTITIONER POINTS: Biochar prepared from waste eggshell was used to removal and recovery phosphorus in wastewater treatment. EGBC has an impressive adsorption capacity that can reach up to 288.83 mg/g. EGBC has excellent adsorption and filtration capabilities, and there is a sudden increase in concentration at 900 min in the breakthrough curve of EGBC. EGBC has good regeneration performance, with an adsorption effect of 65% and an adsorption capacity of 121 mg/g after four desorption and regeneration cycles.

Biochar as Alternative Material for Heavy Metal Adsorption from Groundwaters: Lab-Scale (Column) Experiment Review

The purpose of this manuscript is to present a review of laboratory experiments (including methodology and results) that use biochar, a specific carbon obtained by a pyrolysis process from different feedstocks, as an alternative material for heavy metal adsorption from groundwater. In recent years, many studies have been conducted regarding the application of innovative materials to water decontamination to develop a more sustainable approach to remediation processes. The use of biochar for groundwater remediation has particularly attracted the interest of researchers because it permits the reuse of materials that would be otherwise disposed of, in accordance with circular economy, and reduces the generation of greenhouse gases if compared to the use of virgin materials. A review of the different approaches and results reported in the current literature could be useful because when applying remediation technologies at the field scale, a preliminary phase in which the suitability of the adsorbent is evaluated at the lab scale is often necessary. This paper is therefore organised with a short description of the involved metals and of the biochar production and composition. A comprehensive analysis of the current knowledge related to the use of biochar in groundwater remediation at the laboratory scale to obtain the characteristic parameters of the process that are necessary for the upscaling of the technology at the field scale is also presented. An overview of the results achieved using different experimental conditions, such as the chemical properties and dosage of biochar as well as heavy metal concentrations with their different values of pH, is reported. At the end, numerical studies useful for the interpretation of the experiment results are introduced.

Use of waste marble powder for the synthesis of novel calcium-rich biochar: Characterization and application for phosphorus recovery in continuous stirring tank reactors

This study investigates-for the first time-the synthesis of a novel Ca-rich biochar (N-Ca-B) and its potential use for phosphorus (P) recovery from both synthetic solutions (SS) and treated urban wastewater (TUW) in a continuous stirring tank reactor (CSTR) mode. The novel biochar was synthesized by pyrolysis at 900 °C of a mixture composed of three different materials: animal biomass (poultry manure; PM), lignocellulosic waste (date palm fronds; DPFs), and abundant mineral waste (waste marble powder; WMP). Characterization of N-Ca-B showed that it has good textural properties: well-developed porosity, and high specific surface area. Furthermore, high calcium hydroxide (Ca(OH)2) and calcium oxides (CaO) nanoparticle loads were observed on the biochar surface. The dynamic CSTR assays indicated that the P recovery efficiency mainly depended on the biochar mass, P influent concentration, and, especially, the Ca content of the feeding solution. Owing to its richness in Ca cations, TUW exhibited the highest adsorbed P amount (109.2 mg g-1), i.e., about 14% larger than the SS. P recovery occurs through precipitation as hydroxyapatite, surface complexation, and electrostatic interactions with positively charged biochar particles. In real-world scenarios, CSTR systems can be applied as a tertiary treatment step in existing wastewater treatment plants (WWTPs). Decanted P-loaded biochar can be used in agriculture as a slow-release fertilizer instead of commercial products.

Recent developments in metallic-nanoparticles-loaded biochars synthesis and use for phosphorus recovery from aqueous solutions. A critical review

Phosphorus (P) represents a major pollutant of water resources and at the same time a vital element for human and plants. P recovery from wastewaters and its reuse is a necessity in order to compensate the current important depletion of P natural reserves. The use of biochars for P recovery from wastewaters and their subsequent valorization in agriculture, instead of synthetic industrial fertilizers, promotes circular economy and sustainability concepts. However, P retention by pristine biochars is usually low and a modification step is always required to improve their P recovery efficiency. The pre- or post-treatment of biochars with metal salts seems to be one of the most efficient approaches. This review aims to summarize and discuss the most recent developments (from 2020- up to now) in: i) the role of the feedstock nature, the metal salt type, the pyrolysis conditions, and the experimental adsorption parameters on metallic-nanoparticles-loaded biochars properties and effectiveness in recovering P from aqueous solutions, as well as the dominant involved mechanisms, ii) the effect of the eluent solutions nature on the regeneration ability of P-loaded biochars, and iii) the practical challenges facing the upscaling of P-loaded biochars production and valorization in agriculture. This review shows that the synthesized biochars through slow pyrolysis at relatively high temperatures (up to 700-800 °C) of mixed biomasses with Ca- Mg-rich materials or impregnated biomasses with specific metals in order to from layered double hydroxides (LDHs) biochars composites exhibit interesting structural, textural and surface chemistry properties allowing high P recovery efficiency. Depending on the pyrolysis's and adsorption's experimental conditions, these modified biochars may recover P through combined mechanisms including mainly electrostatic attraction, ligand exchange, surface complexation, hydrogen bonding, and precipitation. Moreover, the P-loaded biochars can be used directly in agriculture or efficiently regenerated with alkaline solutions. Finally, this review emphasizes the challenges concerning the production and use of P-loaded biochars in a context of circular economy. They concern the optimization of P recovery process from wastewater in real-time scenarios, the reduction of energy-related biochars production costs and the intensification of communication/dissemination campaigns to all the concerned actors (i.e., farmers, consumers, stakeholders, and policymakers) on the benefits of P-loaded biochars reuse. We believe that this review is beneficial for new breakthroughs on the synthesis and green application of metallic-nanoparticles-loaded biochars.

Nitrogen retention potentials of magnesium oxide- and sepiolite-modified biochars and their impacts on bacterial distribution under nitrogen fertilization

Mitigating the loss and negative impacts of reactive N from fertilized soils remains a global environmental challenge. To optimize N retention by biochar, bamboo and pig manure biochars were modified as MgO- and sepiolite-biochar composites and characterized. Novel soil application of the modified biochars and their raw forms were comparatively evaluated for N-retention in a fertilized soil leached for 90 days in a column experiment. Changes in N-cycling-related enzyme and bacterial structure were also reported after 90 days. Results revealed low leaching losses of NH₄⁺, which reduced over time across all the treatments. However, while sole fertilizer (F) increased the initial and cumulative NO₃^- leached from the soil, the MgO-bamboo biochar (MgOBF) and sepiolite-bamboo biochar (SBF) treatments reduced leachate NO₃^- by 22.1 % and 10.5 % compared to raw bamboo biochar (BBF) treatment. However, 15.5 % more NO₃^- was leached from the MgO-pig manure biochar-treated soil (MgOPF) compared to its raw biochar treatment (PMBF) after 90 days. Dissolved organic N leached was reduced by 9.2 % and 0.5 % in MgOBF and SBF, as well as 15.4 % and 40.5 % in MgOPF and SPF compared to their respective raw forms. The total N of the biochars, adjustment of surface charges, cation exchange capacity, surface area, pore filling effects, and the formation of potential MgN precipitates on the modified-biochar surfaces regulated N leaching/retention. In addition, the modified biochar treatments reduced the hydrolysis of urea and stimulated some nitrate-reduction-related bacteria crucial for NO₃^- retention. Hence, unlike the raw biochar and MgOPF treatments, MgOBF, SBF, and SPF hold promise in mitigating inorganic-N losses from fertilized soils while improving the soil's chemical properties.

Lead removal from aqueous solutions by olive mill wastes derived biochar: Batch experiments and geochemical modelling

In this study, lead removal from aqueous solutions using biochar derived from olive mill solid and liquid wastes has been investigated by applying batch experiments and geochemical modelling. The batch adsorption experiments included the assessment of several key parameters such as the contact time (kinetic), initial concentration (isotherm), pH, adsorbent dose, and the presence of competitive cations, whilst the geochemical modelling focused on the involved adsorption mechanisms using the PHREEQC code. The kinetic studies showed that lead adsorption is a relatively fast process, where intraparticle diffusion is the rate-limiting step. Biochar dose, solution pH and the presence of competitive ions significantly affected the Pb adsorption effectiveness by the biochar. Especially the higher Pb removal percentages were observed in mono-elemental solutions with high biochar dose at mildly acidic solution pH values. The maximum Pb adsorption capacity of biochar was estimated as 40.8 mg g^-1 which is higher than various biochars derived from sludge, lignocellulosic and animal biomasses. On the other hand, the geochemical modelling employing the PHREEQC code showed that ion exchange and Pb precipitation are the main reactions controlling its removal from aqueous solutions, whilst surface complexation is insignificant, mainly due to the low surface functional groups on the used biochar.

A comparative and modeled approach for three biochar materials in simultaneously preventing the migration and reducing the bioaccessibility of heavy metals in soil: Revealing immobilization mechanisms

The effectiveness and feasibility of the three biochar materials for remediation of arsenic (As) and lead (Pb) contaminated soil were explored in this study. Significant reduction of bioaccessibility and migration risks of both heavy metals have been explained mechanistically by incubation, column experiments and numerical simulation. Langmuir equation fitted As and Pb sorption isotherms better in the control and biochar (BC) amended soils, while Freundlich model was more suitable for iron modified biochar (Fe-BC) and sulfur/iron modified biochar (S/Fe-BC) amended soils, indicating that modified biochar promoted chemical adsorption process for As and Pb. For the three biochar materials, S/Fe-BC showed the best effects on reducing the bioavailability of As and Pb, with a decrease of 40.42%-64.21%. The reduction in bioaccessibility by metal portioning into available and non-available fractions was better for illustrating the mechanisms including adsorption, precipitation/coprecipitation and As(III) oxidation behind S/Fe-BC efficacy. Moreover, S/Fe-BC can effectively inhibit the leaching behavior of As and Pb under acid rain, which increased by 99.89% and 90.18%, respectively, compared with the control. The HYDRUS-1D modeling indicated that S/Fe-BC could continuously treat As (100 mg/L) and Pb (1000 mg/L) contaminated water for 16.22 years and 40.86 years, respectively, and ensure the groundwater quality criteria being met. Based on these insights, we believe that our study will provide meaningful information about the potentials of biochar derived materials for soil heavy metals' remediation.

Preparation, adsorption performance and mechanism of MgO-loaded biochar in wastewater treatment: A review

Biochar is a low cost, porous and solid material with an extremely high carbon content, various types of functional groups, a large specific surface area and many other desirable characteristics. Thus, it is often used as an adsorbent or a loading matrix. Nano-magnesium oxide is a crystalline material with small particles and strong ion exchangeability. However, due to the high surface chemical energy, it easily forms agglomerates of particles. Therefore, to combine the advantages of biochar and magnesium, metal magnesium nanoparticles can be loaded onto the surface of biochar with different modification techniques, resulting in biochars with low cost and high adsorption performance to be used as an adsorption matrix (collectively referred to as Mg@BC). This review presents the effects of different Mg@BC preparation methods and synthesis conditions and summarizes the removal capabilities and adsorption mechanisms of Mg@BC for different types of pollutants in water. In addition, the review proposes the prospects for the development of Mg@BC to solve various problems in the future.

Dynamic Adsorption Properties of Insoluble Humic Acid/Tourmaline Composite Particles for Iron and Manganese in Mine Wastewater

Iron- and manganese-contaminated mine water is widespread around the world, and economical and efficient remediation has become a priority. Insoluble humic acid/tourmaline composite particles (IHA/TM) were prepared by combining inorganic tourmaline (TM) with the natural organic polymer humic acid (HA), and the effects of different calcination temperatures and calcination times of TM and IHA on the adsorption of Fe²⁺ and Mn²⁺ were analyzed. Based on the microscopic characterization of Scanning electron microscopy (SEM), Energy Dispersive Spectroscopy (EDS), Brunnauer–Emmet–Teller (BET), X-ray diffractometer (XRD) and Fourier transform infrared (FTIR), the simultaneous adsorption performance of IHA/TM on Fe²⁺ and Mn²⁺ was studied through dynamic adsorption tests, and a dynamic adsorption model was established. Adsorption regeneration experiments were carried out to further investigate the effectiveness of the composite particles in practical applications. The results show that, when the calcination temperature was 330 °C and the calcination time was 90 min, the removal rates of iron and manganese by the IHA/TM composite particles reached 99.85% and 99.51%, respectively. The curves for penetration of Fe²⁺ and Mn²⁺ ions into the IHA/TM composite particles were affected by the bed height, flow rate and influent concentration. Decreasing the flow rate, decreasing the influent concentration, or increasing the bed height prolonged the operation time of the dynamic column. If the bed height was too low, the penetration point was reached before the expected treatment was achieved, and when the bed height was too high, the removal of Fe²⁺ and Mn²⁺ was slow, and the utilization rate of the adsorbent was also reduced. If the flow rate was too low, longitudinal remixing easily occurred in the column. However, when the flow rate was too high, the speed of Fe²⁺ and Mn²⁺ ions passing through the adsorption layer increased, which reduced the total amount of adsorption. The increase in influent concentration not only reduces the removal rate, but also greatly shortens the total operation time of the dynamic column and reduces the treatment water. The dynamic process for the adsorption of Fe²⁺ and Mn²⁺ by IHA/TM was fitted best by the Thomas model. The adsorption column was continuously regenerated five times, and the results show that the IHA/TM composite particles were suitable for iron and manganese removal from mine wastewater. The research results will provide a reference for the effectiveness of the IHA/TM composite particles in practical applications.

Experimental and numerical study on Cu and Cd migration in different functional-area soils under simulated rainfall conditions

Natural rainfall exerts a significant influence on the migration of heavy metals in soil. However, the knowledge of migration characteristics and release kinetics of heavy metals in contaminated soils under different rainfall intensities still remains unclear. In this study, the simulated rainfall of different intensities was designed to experimentally and numerically investigate Cu and Cd movements in different functional-area (agriculture, industrial, urban) soils. A HYDRUS-2D model was optimized to simulate the migration process of Cu and Cd in soil under different rainfall conditions. The hydraulic properties and solute transport parameters used in the model were estimated based on isothermal adsorption and chloride ion penetration experimental measurements and related model fitting. Furthermore, Cu and Cd BTCs (Breakthrough Curves) were fitted using the HYDRUS-2D inverse solution function with two-site model. The results showed that the order of the migration capacity of Cu and Cd in different functional-area soils was agriculture soil > industrial soil > urban soil, and Cd had a greater risk of groundwater pollution than Cu. With the increase of rainfall intensity, the high proportion of the exchangeable state of Cu and Cd in contaminated soil is easy to be released. Furthermore, the model was proved to describe the distribution of Cu and Cd in the soil profile very well. The present results can improve understanding of the environmental behavior of Cu and Cd in different functional-areas soils and can be used as a basis for risk assessment of Cu and Cd polluting groundwater.

Enhanced transport of heavy metal ions by low-molecular-weight organic acids in saturated porous media: Link complex stability constants to heavy metal mobility

Environment-ubiquitous low-molecular-weight organic acids (LMWOAs) can interact with heavy metal ions and thus affect their mobility in subsurface aquifers. Herein, the effects of LMWOAs (including acetic acid, tartaric acid, malonic acid, oxalic acid, and citric acid) on the mobility of heavy metal ions (including Cd²⁺, Zn²⁺, Ni²⁺, Mn²⁺, and Co²⁺) in porous media were investigated to reveal the role of the stability constants of metal-LMWOA complexes in the mobility of heavy metal ions in porous media. The results showed that the mobility of different metal ions followed the order of Cd²⁺ < Zn²⁺ < Ni²⁺ < Mn²⁺ < Co²⁺ despite of LMWOAs-free or LMWOAs-addition. For each heavy metal, all the organic acids enhanced its transport by forming stable non-adsorbing metal-LMWOA complexes and the enhanced ability followed the order of citric acid > oxalic acid > malonic acid > tartaric acid > acetic acid. An interesting finding was that there was a significantly positive correlation between the enhanced abilities of LMWOAs to metal mobility and the complex stability constants (log K) (R² = 0.801-0.961, p < 0.05), indicating that the complex stability of metal-LMWOA was the dominant factor responsible for the enhanced transport of heavy metal ions. Meanwhile, the linear slope indicated the intensity of enhancement of LMWOAs on heavy metal mobility was heavy metal type-dependent. This study proposed that the complex stability of metal-LMWOA could be an indicator to quantify and predict the impact of LMWOAs on the mobility of heavy metals.

Recent advancements on biochars enrichment with ammonium and nitrates from wastewaters: A critical review on benefits for environment and agriculture

During the last decade, biochars have been considered as attractive and eco-friendly materials with various applications including wastewater treatment, energy production and soil amendments. However, the important nitrogen losses during biochars production using the pyrolysis process have limited their potential use in agriculture as biofertilizer. Therefore, it seems necessary to enrich these biochars with nitrogen sources before their use in agricultural soils. This paper is the first comprehensive review on the assessment of biomass type and the biochars' properties effects on N recovery efficiency from aqueous solutions as well as its release and availability for plants when applying the N-enriched chars in soils. In particular, the N recovery efficiency by raw biochars versus the type of the raw feedstock is summarized. Then, correlations between the adsorption performance and the main physico-chemical properties are established. The main mechanisms involved during ammonium (NH₄-N) and nitrates (NO₃-N) recovery process are thoroughly discussed. A special attention is given to the assessment of the biochars physico-chemical modification impact on their N recovery capacities improvement. After that, the application of these N-enriched biochars in agriculture and their impacts on plants growth as well as methane and nitrous oxide greenhouse gas emissions reduction are also discussed. Finally, the main future development and challenges of biochars enrichment with N from wastewaters and their valorization as biofertilizers for plants growth and greenhouse gas (GHG) emissions reduction are provided. This systematic review is intended to promote the real application of biochars for nutrients recovery from wastewaters and their reuse as eco-friendly fertilizers.

High-efficiency removal of lead/cadmium from wastewater by MgO modified biochar derived from crofton weed

The adsorption performance and mechanisms of Pb²⁺ and Cd²⁺ in wastewater using MgO modified biochar derived from crofton weed (MBCW600) are investigated. The Pb²⁺ and Cd²⁺ adsorption capacities of MBCW600 by the Hill model reach 384.08 mg/g and 207.02 mg/g, respectively, which is larger than that of original biochar. Pb²⁺ could be more easily captured by MBCW600 compared to Cd²⁺ in the multimetal system. Mg²⁺ contributes to Pb²⁺ and Cd²⁺ adsorption among coexisting cations. The exhausted MBCW600 could be well regenerated by simple method after use. The adsorption mechanism study indicates that Pb²⁺ and Cd²⁺ removal are primary contributed to mineral precipitation and ion exchange. The effective treatment volumes of Pb²⁺ and Cd²⁺ wastewater achieve 3050 mL and 2150 mL in the fixed-bed column experiment, respectively. Therefore, MBCW600 presents remarkable adsorption capability, excellent recoverability and large throughput, which shows the potential application in future treatment of wastewater containing heavy metal.

Adsorption of pharmaceuticals in a fixed-bed column using tyre-based activated carbon: Experimental investigations and numerical modelling

Magnetic tyre char (MTC), activated tyre char (ATC) and commercial activated carbon (CAC) were used as packing materials in lab-scale column study for the adsorption of three pharmaceuticals: propranolol (PRO), ciprofloxacin (CIP) and clomipramine (CLO), from aqueous solution. The obtained breakthrough curves (BTCs) suggest that, lower flow rate, greater bed height, higher pH and nano particle size led to increased adsorption of PRO. The lowest adsorption capacity was observed for CIP either from single or ternary solution while it was significantly higher for CLO. Surface area of ATC increased nearly twelve-fold (38.17 to 453.81 m²/g), after thermal and chemical activation and adsorption capacity was comparable to commercial activated carbon. The suitability of Hydrus-1D model incorporating chemical non-equilibrium process to simulate the pharmaceutical transport and fit experimental BTCs was demonstrated (97.29 <R² <99.22) in comparison to other common models (Adams-Bohart, Thomas and Yoon-Nelson). The modelling suggests the existence of non-equilibrium conditions and rate-limited sorption sites and the effect of dispersion and mass transfer mechanisms in the solute transport under dynamic conditions. The cost analysis showed that unit cost for treatment of wastewater using fixed-bed columns of tyre char was calculated to be 1.57 US$/m³ which can be deemed as commercially feasible.

Magnesium-Palm Kernel Shell Biochar Composite for Effective Methylene Blue Removal: Optimization via Response Surface Methodology

This study investigates the properties and potential application of Mg-PKS biochar composite for methylene blue solution (MB) adsorption. The Mg-PKS biochar composite was developed from palm kernel shell biochar via steam activation followed by MgSO4 treatment and carbonization. The effect of process parameters such as solution pH (4-10), contact time (30-90 min) and adsorbent dosage (0.1-0.5 g) were investigated via central composite design, response surface methodology. Results revealed that the Mg-PKS biochar composite has irregular shapes pore structure from SEM analysis, a surface area of 674 m2g-1 and average pore diameters of 7.2195 μm based on BET analysis. RSM results showed that the optimum adsorption of MB onto Mg-biochar composite was at pH 10, 30 min contact time and 0.5 g/100 mL dosage with a removal efficiency of 98.50%. In conclusion, Mg treatment is a potential alternative to other expensive chemical treatment methods for biochar upgrading to the adsorbent.

Optimization of hybrid treatment of olive mill wastewaters through impregnation onto raw cypress sawdust and electrocoagulation

This research investigation proposes a new method for sustainable olive mill wastewater (OMW) treatment and handling. It is based on the combination of its impregnation onto raw cypress sawdust (RCS) followed by electrocoagulation. The retention of OMW compounds onto various RCS doses show an important decrease of its chemical oxygen demand (COD) and its main cation and anion content. The maximum retention efficiencies of COD, Na⁺, K⁺, Ca²⁺, Mg²⁺, Cl^-, [Formula: see text], and [Formula: see text] were about 51.0%, 75.3%, 28.7%, 77.9%, 84.7%, 41.1%, 98.3%, and 90.9%, respectively, for the highest RCS dose (200 g L^-1). This organic matter- and nutrient-loaded biomass could be thermochemically converted through pyrolysis into biofuel and biochar for energetic and agronomic purposes, respectively. The treatment by electrocoagulation of the pre-treated OMW using mild steel electrodes could be considered an attractive treatment method since 75.6% of COD removal efficiency was achieved. Besides, this approach permits a significant energy consumption reduction by 46% as compared with the electrocoagulation process alone. It allows also a significant improvement of the treated effluent quality in terms of both organic and mineral contents that could be reused for the irrigation of olive trees in the context of circular economy.

Static and Dynamic Investigations on Leaching/Retention of Nutrients from Raw Poultry Manure Biochars and Amended Agricultural Soil

In this study, nutrients release/adsorption from/by raw poultry manure-derived biochar produced at a pyrolysis temperature of 600 °C (RPM-B) was assessed under static and dynamic conditions. Batch sequential leaching experiments of RPM-B for a total contact time of 10 days showed that both phosphorus and potassium were slowly released but with higher amounts compared to various other animal- and lignocellulosic-derived biochars. The cumulated released P and K amounts were assessed to 93.6 and 17.1 mg g−1, which represent about 95% and 43% of their original contents in the RPM-B, respectively. The column combined leaching/adsorption experiments showed that amending an alkaline sandy agricultural soil with two doses of RPM-B (at 5% and 8% w:w) resulted in an efficient retention of NO3-N and NH4-N, and on the contrary, important leached amounts of PO4-P, K+, Mg2+, and Ca2+ but with relatively slow kinetic release rates for a long period. Even after 40 days of dynamic leaching, these latter nutrients continued to be released with kinetic rates lower than 10 mg kg−1 d−1. Thus, compared to synthetic fertilizers, RPM-B valorization as organic amendment for poor semiarid soils could be considered as an attractive, eco-friendly, and sustainable waste recycling option.

Use of Lignite as a Low-Cost Material for Cadmium and Copper Removal from Aqueous Solutions: Assessment of Adsorption Characteristics and Exploration of Involved Mechanisms

Lignite, as an available and low-cost material, was tested for cadmium (Cd) and copper (Cu) removal from aqueous solutions under various static experimental conditions. Experimental results showed that the removal efficiency of both metals was improved by increasing their initial concentrations, adsorbent dosage and aqueous pH values. The adsorption kinetic was very rapid for Cd since about 78% of the totally adsorbed amounts were removed after a contact time of only 1 min. For Cd and Cu, the kinetic and isothermal data were well fitted with pseudo-second order and Freundlich models, respectively, which suggests that Cd/Cu removal by lignite occurs heterogeneously on multilayers surfaces. The maximum Langmuir’s adsorption capacities of Cd and Cu were assessed to 38.0 and 21.4 mg g−1 and are relatively important compared to some other lignites and raw natural materials. Results of proximate, scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS), Fourier transform infrared spectroscopy (FTIR) and X-Ray diffraction (XRD) showed that the removal of these metals occurs most likely through a combination of cation exchange and complexation with specific functional groups. The relatively high adsorption capacity of the used lignite promotes its future use as a low cost material for Cd and Cu removal from effluents, and possibly for other heavy metals or groups of pollutants.

Preparation of nitrogen doped magnesium oxide modified biochar and its sorption efficiency of lead ions in aqueous solution

A N-doped couping MgO-modified biochar (MgO-N-BC) was synthesized from corncob-to-xylose residue by two-step slow pyrolysis method. The biochar exhibited a remarkable Pb(II) sorption capacity (maximum 1429 mg·g^-1) in aqueous solution. The sorption of Pb(II) onto MgO-N-BC best fitted Freundlich model and pseudo-second-order equation. Further analysis demonstrated the final product of Pb were mainly hexagonal crystal hydrocerussite flakes. The combine of ion-exchange and precipitation process play key role in the sorption of Pb(II), while interactions between Pb(II) and functional groups work, too. The sorption capacity decreased by 63.5% with CO₂ free, however over supply of CO₂ effects little on the sorption capacity while that can shorten equilibrium time from near 360 min to about 30 min. Only few co-existing ions such as Ba²⁺ and Fe³⁺ can decrease the sorption partly, and NH₄⁺ block the sorption obviously, while Mg²⁺ had an enhancement effect.

Recent advances in biochar application for water and wastewater treatment: a review

In the past decade, researchers have carried out a massive amount of research on the application of biochar for contaminants removal from aqueous solutions. As an emerging sorbent with great potential, biochar has shown significant advantages such as the broad sources of feedstocks, easy preparation process, and favorable surface and structural properties. This review provides an overview of recent advances in biochar application in water and wastewater treatment, including a brief discussion of the involved sorption mechanisms of contaminants removal, as well as the biochar modification methods. Furthermore, environmental concerns of biochar that need to be paid attention to and future research directions are put forward to promote the further application of biochar in practical water and wastewater treatment.

Effects of excessive impregnation, magnesium content, and pyrolysis temperature on MgO-coated watermelon rind biochar and its lead removal capacity

MgO-coated watermelon rind biochar (MWRB) is a potentially highly-effective waste-derived material in environmental applications. This research aims to provide valuable insights into the optimization of the production of MWRB for superior environmental performance. It was found that the Mg content of the MWRB could be easily controlled by adjusting the Mg/feedstock mass ratio during excessive impregnation. The BET surface area was found to first increase and then decrease as the Mg content of the MWRB (produced at 600 °C) increased from 1.52% to 10.1%, with an optimal surface area of 293 m²/g observed at 2.51%. Similarly, an optimum pyrolysis temperature of 600 °C was observed in the range of 400-800 °C for a maximum surface area of the MWRB at a fixed Mg/feedstock ratio of 0.48% (resulting in MWRBs with Mg contents of 1.89-2.51%). The Pb removal capacity of the MWRB (produced at 600 °C) increased with increasing Mg content, with a greatest Pb removal capacity of 558 mg/g found for the MWRB with the highest Mg content (10.1%), an improvement of 208% over the 181 mg/g Pb removal capacity of unmodified WRB produced at 600 °C. The Pb removal capacity of the MWRB (produced with 1.89-2.51% Mg) was also discovered to increase from 81.7 mg/g (at 400 °C) to 742 mg/g (at 700 °C), before dropping to 368 mg/g at 800 °C. These findings suggest that the MWRB can be more efficiently utilized in soil and water remediation by optimizing its synthesis conditions.

A Review of Non-Soil Biochar Applications

Biochar is the solid residue that is recovered after the thermal cracking of biomasses in an oxygen-free atmosphere. Biochar has been used for many years as a soil amendment and in general soil applications. Nonetheless, biochar is far more than a mere soil amendment. In this review, we report all the non-soil applications of biochar including environmental remediation, energy storage, composites, and catalyst production. We provide a general overview of the recent uses of biochar in material science, thus presenting this cheap and waste-derived material as a high value-added and carbonaceous source.

A review of biochar-based sorbents for separation of heavy metals from water

Biochar is the low-cost and environmental-friendly material which has shown a great potential for separation of heavy metals from water. The previous studies have established a superior role of biochar over other materials, such as activated carbon and inorganic sorbents (iron based) in efficient removal of toxic heavy metals from aqueous systems. Among the various factors influencing heavy metals sorption ability of biochar, types of feedstock/biomass and pyrolysis temperature play a significant role. The goal of this review is to increase our understanding of heavy metals sorption behavior by biochars - this is important as heavy metals sorption is driven based on biochar type, heavy metals species which involve numerous mechanisms, including the physical binding, complexation, ion exchange, surface precipitation and electrostatic interactions. In addition, this review paper describes various approaches to improve heavy metal sorption capacity of biochars by steam and acids/bases activations and impregnation of biochar-based composites with minerals, organic compounds and carbon-rich materials. The physical/chemical activation of biochars can improve the surface area, thus leading to their improved functionality, while modification/pretreatment methods help in synthesizing composites using biochar as a supporting media to develop new sorbents with efficient surface attributes for heavy metals removal from aqueous solutions.

Effect of Biochar Application Rates on the Hydraulic Properties of an Agricultural-Use Boreal Podzol

Boreal agriculture struggles with soils of lower agronomic value, most of which are sandy with a low water holding capacity (WHC) and prone to nutrient leaching. Biochar amendments are associated with positive effects on soil hydraulic properties and enhanced nutrient retention. However, these effects are strongly related to feedstock type and pyrolysis parameters and depend on biochar application rates and soil types. While biochar could increase the productivity of boreal agriculture by improving water and nutrient use efficiency, little is known about its effects on hydraulic processes in podzol. In this study, we investigated the effects of biochar rates (10, 20, 40, 80 Mg carbon ha−1) and maturity on soil hydrology for an agriculturally used Podzol in Labrador, Canada. The in-situ soil water content (SWC) and weather data over an entire growing season were analysed. Hydrus 1D simulations were used to estimate changes in water fluxes. SWC showed clear differentiation among storage parameters (i.e., initial, peak and final SWC) and kinetic parameters (i.e., rate of SWC change). Storage parameters and soil wetting and drying rates were significantly affected by biochar rates and its maturity. The magnitude of the changes in SWC after either wetting or drying events was statistically not affected by the biochar rate. This confirms that biochar mostly affected the WHC. Nevertheless, reductions in cumulative lower boundary fluxes were directly related to biochar incorporation rates. Overall, biochar had positive effects on hydrological properties. The biochar rate of 40 Mg C ha−1 was the most beneficial to agriculturally relevant hydraulic conditions for the tested Podzol.

Comparative efficiency of peanut shell and peanut shell biochar for removal of arsenic from water

Contamination of surface water and groundwater streams with carcinogenic chemicals such as arsenic (As) has been a major environmental issue worldwide, and requires significant attention to develop new and low-cost sorbents to treat As-polluted water. In the current study, arsenite (As(III)) and arsenate (As(V)) removal efficiency of peanut shell biochar (PSB) was compared with peanut shell (PS) in aqueous solutions. Sorption experiments showed that PSB possessed relatively higher As removal efficiency than PS, with 95% As(III) (at pH 7.2) and 99% As(V) (at pH 6.2) with 0.6 g L^-1 sorbent dose, 5 mg L^-1 initial As concentration, and 2 h equilibrium time. Experimental data followed a pseudo-second-order model for sorption kinetics showing the dominance of chemical interactions (surface complexation) between As and surface functional groups. The Langmuir model for sorption isotherm indicated that As was sorbed via a monolayer sorption process. The X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) spectroscopy analyses revealed that the hydroxyl (-OH) and aromatic surface functional (C=O, C=C-C, and -C-H) groups contributed significantly in the sorption of both As species from aqueous solutions through surface complexation and/or electrostatic reactions. We demonstrate that the pyrolysis of abandoned PS yields a novel, low-cost, and efficient biochar which provides dual benefits of As-rich water treatment and a value-added sustainable strategy for solid waste disposal.

Development of magnetic porous coordination polymer adsorbent for the removal and preconcentration of Pb(II) from environmental water samples

A novel porous coordination polymer adsorbent (BTCA-P-Cu-CP) based on a piperazine(P) as a ligand and 1,2,4,5-benzenetetracarboxylic acid (BTCA) as a linker was synthesized and magnetized to form magnetic porous coordination polymer (BTCA-P-Cu-MCP). Fourier transform infrared (FTIR), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), field emission scanning electron microscope(FESEM), energy-dispersive X-ray spectroscopy(EDS), CHN, and Brunauer-Emmett-Teller(BET) analysis were used to characterize the synthesized adsorbent. BTCA-P-Cu-MCP was used for removal and preconcentration of Pb(II) ions from environmental water samples prior to flame atomic absorption spectrometry(FAAS) analysis. The maximum adsorption capacity of BTCA-P-Cu-MCP was 582 mg g^-1. Adsorption isotherm, kinetic, and thermodynamic parameters were investigated for Pb(II) ions adsorption. Magnetic solid phase extraction (MSPE) method was used for preconcentration of Pb(II) ions and the parameters influencing the preconcentration process have been examined. The linearity range of proposed method was 0.1-100 μg L^-1 with a preconcentration factor of 100. The limits of detection and limits of quantification for lead were 0.03 μg L^-1 and 0.11 μg L^-1, respectively. The intra-day (n = 7) and inter-day (n = 3) relative standard deviations (RSDs) were 1.54 and 3.43% respectively. The recoveries from 94.75 ± 4 to 100.93 ± 1.9% were obtained for rapid extraction of trace levels of Pb(II) ions in different water samples. The results showed that the BTCA-P-Cu-MCP was steady and effective adsorbent for the decontamination and preconcentration of lead ions from the aqueous environment.

Synthesis of novel waste batteries-sawdust-based adsorbent via a two-stage activation method for Pb2+ removal

The novel waste alkaline battery-sawdust-based adsorbents (WABAs) are prepared by a two-stage activation method with the negative electrode materials as activator and different doping ratio of the positive electrode materials and pine sawdust as raw materials. The characteristics of the WABAs are analyzed by SEM, XRD, FT-IR, and specific surface determination (S_BET). The Pb²⁺ adsorption properties of the WABAs are studied by changing the pH of solution, contact time, initial concentration, and temperature. It turns out that when the doping mass ratio is 1:4, the optimum performance of the WABAs is obtained, and comparing with the samples prepared by pure biomass, the iodine adsorption value, total acid groups, and cation exchange capacity (CEC) separately increased by 13, 106, and 22%, respectively. Kinetic studies show that the pseudo-second-order model is more suitable for describing the Pb²⁺ adsorption process and the Langmuir isotherm provides better fitting to the equilibrium data. The thermodynamic parameters indicate the adsorption process would be spontaneous and endothermic. Besides, the prepared WABAs could be reused for 5 cycles with high removal efficiency. This study provides an alternative route for waste alkaline battery treatment. Graphical abstract The schematic diagram of synthesis of waste batteries-sawdust-based adsorbent via a two-stage activation method for Pb²⁺ removal.

Biochar modification to enhance sorption of inorganics from water

Biochar can be used as a sorbent to remove inorganic pollutants from water but the efficiency of sorption can be improved by activation or modification. This review evaluates various methods to increase the sorption efficiency of biochar including activation with steam, acids and bases and the production of biochar-based composites with metal oxides, carbonaceous materials, clays, organic compounds, and biofilms. We describe the approaches, and explain how each modification alters the sorption capacity. Physical and chemical activation enhances the surface area or functionality of biochar, whereas modification to produce biochar-based composites uses the biochar as a scaffold to embed new materials to create surfaces with novel surface properties upon which inorganic pollutants can sorb. Many of these approaches enhance the retention of a wide range of inorganic pollutants in waters, but here we provide a comparative assessment for Cd²⁺, Cu²⁺, Hg²⁺, Pb²⁺, Zn²⁺, NH₄⁺, NO₃^-, PO₄^3-, CrO₄^2- and AsO₄^3-.

Optimization of a cationic dye removal by a chemically modified agriculture by-product using response surface methodology: biomasses characterization and adsorption properties

The present study investigates the alkaline modification of raw orange tree sawdust (ROS) for an optimal removal of methylene blue (MB), as a cationic dye model, from synthetic solutions. The effects of operating parameters, namely, sodium hydroxide (NaOH) concentrations, ROS doses in NaOH solutions, stirring times, and initial MB concentrations on dye removal efficiency, were followed in batch mode. The process optimization was performed through the response surface methodology approach (RSM) by using Minitab17 software. The results showed that the order of importance of the followed parameters was NaOH treatment concentrations > stirring times > initial MB concentrations > ROS doses in NaOH solutions. The optimal experimental conditions ensuring the maximal MB removal efficiency was found for a NaOH treatment concentration of 0.14 M, a stirring time of 1 h, a ROS dose in NaOH solutions of 50 g L^-1, and an initial MB concentration of 69.5 mg L^-1. Specific analyses of the raw and alkali-treated biomasses, e.g., SEM/EDS and XRD analyses, demonstrated an important modification of the crystalline structure of the wooden material and a significant increase in its surface basic functional groups. Kinetic and isotherm studies of MB removal from synthetic solutions by ROS and the alkali-treated material (ATOS) showed that for both adsorbents, the pseudo-second-order and Langmuir model fitted the best the experimental data, respectively, which indicates that MB removal might be mainly a chemical and a monolayer process. Furthermore, thanks to the chemical modification of the ROS, the MB maximal uptake capacity has increased from about 39.7 to 78.7 mg g^-1. On the other hand, due to the competition phenomenon, the coexistence of MB and Zn(II) ions could significantly decrease the MB removal efficiency. A maximal decrease of about 32 % was registered for an initial Zn(II) concentration of 140 mg L^-1. Desorption experiments undertaken at natural pH (without adjustment: pH = 6) and with different NaCl concentrations emphasized that the adsorbed MB could be significantly desorbed from both the tested materials, offering their possible reuse as efficient adsorbents. All these results confirmed that NaOH-treated orange tree sawdust could be considered as an efficient, economic, and ecological alternative for the removal of cationic dyes from industrial wastewaters.