Fabrication of novel magnetic chitosan grafted with graphene oxide to enhance adsorption properties for methyl blue

Efficient Removal of Methylene Blue Dye from Aqueous Media Using Facilely Synthesized Magnesium Borate/Magnesium Oxide Nanostructures

Methylene blue dye in water sources can pose health risks to humans, potentially causing methemoglobinemia, a condition that impairs the blood's ability to carry oxygen. Hence, the current study investigates the synthesis of novel magnesium borate/magnesium oxide (Mg3B2O6/MgO) nanostructures and their efficiency in removing methylene blue dye from aqueous media. The nanostructures were synthesized using the Pechini sol-gel method, which involves a reaction between magnesium nitrate hexahydrate and boric acid, with citric acid acting as a chelating agent and ethylene glycol as a crosslinker. This method helps in achieving a homogeneous mixture, which, upon calcination at 600 and 800 °C, yields Mg3B2O6/MgO novel nanostructures referred to as MB600 and MB800, respectively. The characterization of these nanostructures involved techniques like X-ray diffraction (XRD), Fourier-transform infrared (FTIR) spectroscopy, N2 gas analyzer, and field-emission scanning electron microscope (FE-SEM). These analyses confirmed the formation of orthorhombic Mg3B2O6 and cubic MgO phases with distinct features, influenced by the calcination temperature. The mean crystal size of the MB600 and MB800 samples was 64.57 and 79.20 nm, respectively. In addition, the BET surface area of the MB600 and MB800 samples was 74.63 and 64.82 m2/g, respectively. The results indicated that the MB600 sample, with its higher surface area, generally demonstrated better methylene blue dye removal performance (505.05 mg/g) than the MB800 sample (483.09 mg/g). The adsorption process followed the pseudo-second-order model, indicating dependency on available adsorption sites. Also, the adsorption process matched well with the Langmuir isotherm, confirming a homogeneous adsorbent surface. The thermodynamic parameters revealed that the adsorption process was physical, exothermic, and spontaneous. The MB600 and MB800 nanostructures could be effectively regenerated using 6 M HCl and reused across multiple cycles. These findings underscore the potential of these nanostructures as cost-effective and sustainable adsorbents for methylene blue dye removal.

Preparation magnetic graphene oxide/diethylenetriamine composite for removal of methylene blue from aqueous solutions

Graphene oxide (GO) and its derivatives have several applications in many areas such as environmental and energy materials, water treatment and biomedical technologies. Because of having various polar groups on its surface, GO is considered as an excellent adsorbent. However, for many applications such as adsorption of pollution from aqueous solutions, chemical functionalization of graphene oxide is often a necessary requirement. In the present study, a new composite from graphene oxide, diethylenetriamine (DETA) and silica coated MnFe2O4 nanoparticles (GO/DETA/MnFe2O4@SiO2) was prepared. The structure, thermal stability and magnetic properties of the composite were studied by FT-IR, XRD, SEM, EDS, VSM and TGA spectroscopic methods. The prepared composite showed magnetic property with a saturation magnetization of 3.0 emu/g. The adsorption properties of GO/DETA/MnFe2O4@SiO2 composite for methylene blue (MB) in aqueous solution were studied using batch method. The effects of important parameters on the surface adsorption process of MB, including pH, contact time, adsorbent dosage and initial dye concentration were investigated. The adsorption isotherm was in accordance with Langmuir model showing surface homogeneity of the adsorbent. According to the Langmuir analysis, the maximum adsorption capacity (qm) of GO/DETA/MnFe2O4@SiO2 composite for MB was found to be 243.91 mg/g. The kinetic studies showed that the adsorption was pseudo first-order process. In addition, the thermodynamic studies indicated the adsorption was spontaneous and endothermic process.

Rapid eco-friendly selective dye removal using modified chitosan-based sponges: Synthesis, characterization, and application

The ongoing challenge of water scarcity persists alongside a concerning rise in water pollution driven by population expansion and industrial development. As a result, urgent measures are imperative to address the pressing need for a clean and sustainable water supply. In this study, a sustainable and green approach was utilized to prepare four chitosan-based sponges from a chemically modified chitosan with different alkyl chains in aqueous medium and at room temperature. The resulting sponges displayed excellent stability in water with outstanding dye removal efficiency. The adsorption capacity was associated with the alkyl chain length incorporated to the polymer backbone. All sponges displayed a high adsorption capacity of methyl orange (MO) ranges between 238 and 380 mg g-1, while a low capacity were obtained for methylene blue (MB) and Rhodamine B (RB). Competitive adsorption experiments were conducted on binary and ternary mixtures to assess the selective removal of MO from a mixture of dyes in which the separation factor was found to be ranging between 1.6 and 32. The adsorption kinetics isotherms of all sponges followed the pseudo-second-order, and the Langmuir model was found to be more suitable than the Freundlich for the adsorption of MO on the sponges. The chitosan-based sponges showed stable performance, robustness and reusability over 5 adsorption-desorption cycles, indicating their great potential for water treatment applications.

Superior adsorption and removal of industrial dye from aqueous solution via magnetic silver metal-organic framework nanocomposite

The indirect emission had a negative influence on the ecosystem of enormous amounts of harmful dyes into water. Fe3O4@Ag-MOF was successfully fabricated to capture Gentine violet (GV)) as a model example of cationic dye from their aqueous solutions was evaluated in this search as a method to eliminate dyes from water contaminants. FTIR, XPS, BET, TGA, SEM, TEM, and XRD have all been used to study this adsorbent in order to determine its structural and chemical characteristics as well as to interpret its binding mechanisms. According to the results of the characterization, the synthesized composite had a size about 45 nm, a surface area of 856.06 m2/g, and considerable magnetic characteristics (66.2 emug-1). Consequently, we created mesoporous surfaces that had a strong ability to interface and absorb GV dye. It is possible to use the pseudo-second order rate equation to characterize the kinetic profile., while the Langmuir equation fits isotherm models. At pH 9, maximum sorption capacities can reach 1.68 mmol.g-1. Additionally, the investigations of temperature profiles indicated the endothermic process and Thermodynamic parameters were discovered as, ΔG°, ΔH° and ΔS° The synthesized adsorbent had an interestingly high reusability of > 92 percent up to the sixth cycle. These findings revealed that a mixture of electrostatic interactions, π-π stacking, hydrogen bonds, and pore filling were involved in the GV adsorption mechanism. Fe3O4@Ag-MOF was successful in demonstrating its effectiveness as a point-of-use colour collection candidate from actual dyeing effluents.

Polycarboxylate functionalized magnetic nanoparticles Fe3O4@SiO2@CS-COOH: Preparation, characterization, and immobilization of bovine serum albumin

Magnetic nanoparticles with increasing superparamagnetism and magnetic targeting have found widespread application in fields such as food and medicine. In this study, polycarboxylated magnetic nanoparticles (Fe3O4@SiO2@CS-COOH) were prepared by surface functionalizing iron tetraoxide (Fe3O4) nanoparticles with ethylenediaminetetraacetic acid (EDTA) as a modifier. The appropriate degree of functionalization modification was obtained by adjusting the EDTA concentration and the ratio of cross-linking agents. The prepared magnetic nanoparticles were analyzed with structural and property characterization. The results showed that the Fe3O4@SiO2@CS-COOH magnetic nanoparticles prepared with 4 % EDTA and cross-linking agents at a molar ratio of 3:4 were uniform in particle size, with an average size of roughly 7 nm, and possessed an abundant carboxylate content (310.8064 μmol/g) and a high magnetization intensity (35.05 emu/g). As a model protein, bovine serum albumin (BSA) was immobilized on the surface of magnetic particles. The largest amount of immobilized protein was 500.4376 mg BSA/g at pH 4.0 and no extra salt ions. According to molecular docking simulations, its immobilization was due to the interaction of amino and carboxyl groups at the Fe3O4@SiO2@CS-COOH/BSA interface. Fe3O4@SiO2@CS-COOH possesses a large number of carboxyl groups, strong protein immobilization, and magnetic responsiveness, which may have potential applications in biomedical and food fields.

Ecofriendly Approach on the Removal of Reactive Orange 107 from Aqueous Solutions Using Cladophora Species as a Novel Biosorbent

The efficiency of Cladophora species for the removal of Reactive Orange 107 (RO107) from the aqueous solution was evaluated through batch adsorption studies by optimising various process parameters such as pH (3-8), dye concentration (100-500 mg/l), biosorbent concentration (100-500 mg/l), temperature (25-45 °C) and contact time (12-108 h). The results revealed that the optimum conditions for RO107 decolourisation (87%) was found on 72 h of incubation with 100 mg/l dye concentration amended with 200 mg/l biosorbent at pH 6 at 25 °C. The mechanism of dye adsorption was evaluated using isotherms, kinetics and thermodynamic models. The experimental data fitted well with Langmuir isotherm and pseudo-second-order kinetic models. Thermodynamic studies revealed that the adsorption process was endothermic, spontaneous and feasible in nature. Recovery of RO107 from the Cladophora sp. was maximum when 0.1 M HNO3 was used as an eluent. UV-Visible, FT-IR and SEM analyses reveal the interaction between the biosorbent-adsorbate and confirm the process of decolourisation by Cladophora sp. In order to evaluate the nature of the untreated and treated dye solutions, toxicological studies were conducted and the results revealed that the treated dye solution was non- toxic as compared with untreated dye solution. The results of the docking study proved that there was a substantial binding energy between RO107 and the protein (Cytochrome C6) of Cladophora sp. Hence, Cladophora sp. proves to be a promising biosorbent to decolourise RO107 and its potential can be explored in the textile sectors.

Exploration of a novel electrochemical CN coupling process: Urea synthesis from direct air carbon capture with nitrate wastewater

Direct air capture (DAC) can be used to decrease the CO2 concentration in the atmosphere, but this requires substantial energy consumption. If residual waste carbon (in the form of bicarbonate solution) from DAC can be directly reused, it might present a novel method for overcoming the aforementioned challenges. Electrochemical CN coupling methods for synthesizing urea have garnered considerable attention for waste carbon utilization, but the carbon source is high-purity CO2. No research has been conducted regarding the application of bicarbonate solution as the carbon source. This study proposes a proof-of-concept electrochemical CN coupling process for synthesizing urea using bicarbonate solution from DAC as the carbon source and nitrate from wastewater as the nitrogen source. These results confirmed the feasibility of synthesizing urea using a three-electrode system employing TF and CuInS2/TF as the working electrodes via potentiostatic electrolysis. Under the optimal conditions (initial pH 5.0 and applied potential of -1.3 V vs. Ag/AgCl), the urea yield after 2 h of electrolysis reached 3017.2 μg h-1 mgcat.-1 and an average Faradaic efficiency of 19.6 %. The in-situ attenuated total reflection surface-enhanced infrared absorption spectroscopy indicated a gradual increase in the intensity of the -CONH bond signal on the surface of the CuInS2/TF electrode as the reaction progressed. This implied that this bond may be a key chemical group in this process. The density functional theory calculations demonstrated that *CONH was a pivotal intermediate during CN coupling, and a two-step CN coupling reaction path was proposed. *NH + *CO primarily transformed into *CONH, followed by the conversion reaction of *CONH + *NO to *NOCONH2. This study offers a groundbreaking approach for waste carbon utilization from DAC and holds the potential to furnish technical underpinnings for advancing electrochemical CN coupling methods.

Novel soy protein isolate/sodium alginate-based functional aerogel for efficient uptake of organic dye from effluents

In response to the increasing global concern regarding water pollution, there is a growing demand for the development of novel adsorbents capable of effectively eliminating hazardous organic pollutants from effluents. In this study, we present a functional soy protein isolate (SPI)/sodium alginate (ALG)/polyethyleneimine (PEI) aerogel prepared via a facile chemical crosslinking process as a novel adsorbent with excellent capabilities for removing toxic methyl blue (MB) dye from effluents. Thanks to the synergistic dense oxygen and nitrogen-containing functional groups in the networks, the ALG/SPI/PEI (ASP) aerogel displayed high adsorption capacity for MB (106.3 mg/g) complying the adsorption kinetics and isotherm with the pseudo-second-order and Langmuir models, respectively. Remarkably, the MB adsorption capability of the ASP aerogel surpasses that of its pristine counterpart and outperforms recently reported adsorbents. Moreover, the aerogel maintained >80% of initial adsorption capability in the fourth regenerative cycle, indicating excellent reusability. The superior MB adsorbability coupled with high-efficiency regenerability in this study reveal the significant potential of ASP aerogel in efficiently eliminating organic dye from wastewater.

Graphene oxide nanosheets immobilised on honeycomb pore structure of pomelo peel for enhanced removal of methylene blue

Herein, for the first time, a simple, green, direct immersion immobilisation method is reported for graphene oxide (GO) nanosheets using pomelo peel (PL) as a substrate. A GO/PL porous sponge was successfully prepared and used to remove methylene blue (MB) from dye wastewater. Considering the porosity, hydrophilicity and elasticity of the PL, the PL was placed in a GO aqueous suspension through direct immersion immobilisation. The carboxyl and hydroxyl groups in the peel could effectively capture and immobilise the GO nanosheets. GO was adsorbed into the PL pores and dispersed throughout the PL. Finally, the prepared super-hydrophilic and elastic GO/PL exhibited excellent adsorption performance towards MB in dye wastewater. The adsorption results revealed that the adsorption behaviour was consistent with the Langmuir isotherm and quasi-secondary kinetic models. The maximum equilibrium adsorption capacity of GO/PL towards MB was 124.2 mg/g, exceeding the values obtained for most of the previously reported adsorbents. Moreover, after five consecutive adsorption-desorption cycles, GO/PL retained 75% of its initial adsorption capacity. Mechanistic analysis revealed that pore filling, electrostatic attraction, ion exchange and hydrogen bonding interactions are the primary driving forces facilitating MB adsorption.

Optimization, Kinetics, and Isotherm Studies of Methyl Thioninium Chloride Removal from Simulated Solutions Using Chitosan Derivatives

Methylene blue (MB) dye or methyl thioninium chloride is one of the hazardous cationic dyes that are discharged into the textile effluent causing a highly negative environmental impact. The present work targets the investigation of the adsorption performance of some chitosan-modified products toward the MB dye from simulated solutions. The claimed chitosan derivatives were prepared, characterized, and applied for the removal of lead and copper cations from an aqueous medium in a previous work. These include: N,O-carboxymethyl chitosan (N,O-CM/Cs), chitosan grafted with glutaraldehyde (Cs/GA), chitosan cross-linked with GA/epichlorohydrin (Cs/GA/ECH), and chitosan cross-linked with glutaraldehyde/methylene bis(acrylamide) (Cs/GA/MBA). The modified chitosan derivatives in this study displayed outstanding mechanical qualities, exceptional reusability, and a significant amount of adsorption capacity. The ability of prepared Cs derivatives to eradicate MB was as follows: N,O-CM/Cs (95.1 mg/g) < Cs/GA (120.1 mg/g) < Cs/GA/ECH (220.1 mg/g) < Cs/GA/MBA (270.0 mg/g). The swelling performance of the prepared sorbents was verified under different experimental conditions, and the data revealed that the maximum swelling was attained at pH = 9, temperature 55 °C, and after 24 h. The produced Cs derivatives showed exceptional reusability by maintaining higher adsorption effectiveness throughout five cycles. The MB dye was adsorbed onto the modified derivatives according to pseudo-second-order kinetics and the Langmuir model. Moreover, the adsorption process was monitored via atomic force microscopy to verify the differences between the dye-free and dye-loaded adsorbents.

Next-Generation Water Treatment: Exploring the Potential of Biopolymer-Based Nanocomposites in Adsorption and Membrane Filtration

This review article focuses on the potential of biopolymer-based nanocomposites incorporating nanoparticles, graphene oxide (GO), carbon nanotubes (CNTs), and nanoclays in adsorption and membrane filtration processes for water treatment. The aim is to explore the effectiveness of these innovative materials in addressing water scarcity and contamination issues. The review highlights the exceptional adsorption capacities and improved membrane performance offered by chitosan, GO, and CNTs, which make them effective in removing heavy metals, organic pollutants, and emerging contaminants from water. It also emphasizes the high surface area and ion exchange capacity of nanoclays, enabling the removal of heavy metals, organic contaminants, and dyes. Integrating magnetic (Fe2O4) adsorbents and membrane filtration technologies is highlighted to enhance adsorption and separation efficiency. The limitations and challenges associated are also discussed. The review concludes by emphasizing the importance of collaboration with industry stakeholders in advancing biopolymer-based nanocomposites for sustainable and comprehensive water treatment solutions.

Developments and application of chitosan-based adsorbents for wastewater treatments

Water quality is deteriorating continuously as increasing levels of toxic inorganic and organic contaminants mostly discharging into the aquatic environment. Removal of such pollutants from the water system is an emerging research area. During the past few years use of biodegradable and biocompatible natural additives has attracted considerable attention to alleviate pollutants from wastewater. The chitosan and its composites emerged as a promising adsorbents due to their low price, abundance, amino, and hydroxyl groups, as well as their potential to remove various toxins from wastewater. However, a few challenges associated with its practical use include lack of selectivity, low mechanical strength, and solubility in acidic medium. Therefore, several approaches for modification have been explored to improve the physicochemical properties of chitosan for wastewater treatment. Chitosan nanocomposites found effective for the removal of metals, pharmaceuticals, pesticides, microplastics from the wastewaters. Nanoparticle doped with chitosan in the form of nano-biocomposites has recently gained much attention and proven a successful tool for water purification. Hence, applying chitosan-based adsorbents with numerous modifications is a cutting-edge approach to eliminating toxic pollutants from aquatic systems with the global aim of making potable water available worldwide. This review presents an overview of distinct materials and methods for developing novel chitosan-based nanocomposites for wastewater treatment.

Kinetic adsorption of methyl blue dye from aqueous solution by PVC/PVC-based copolymer containing quaternary amine

The present study has investigated the use of a blend polymer polyvinyl chloride/polyvinyl chloride-graft-poly[2-(dimethylamino) ethyl methacrylate containing a quaternary amine in its structure (PVC/PVC-g-PDMAEM(N⁺)) as an adsorbent for the removal of methyl blue dye from aqueous solution. The synthesized polymer blend has been characterized by Fourier Transform Infrared Spectroscopy (FT-IR), scanning Electron Microscope-energy-dispersive spectroscopy (SEM-EDX), and the scanning Spectrophotometer Ultraviolet-visible (UV-Vis). The adsorption studies have been performed by batch experiments. Moreover, the pH effect, adsorbent dose, initial dye concentration, and contact time effect have been explored. Furthermore, the kinetic experimental data have been analyzed using pseudo-first and pseudo-second-order models. The results have shown that the adsorption process is more described by the pseudo-second-order model with a high determination coefficient. The equilibrium adsorption data have been analyzed using three widely applied isotherms: Langmuir, Freundlich, and Tempkin. The best fit was found to be Freundlich isotherm with maximum monolayer adsorption of Methyl Blue (MB) equal to 142.86 mg/g, which was observed at pH = 7. The results have indicated that the PVC/PVC-g-PDMAEM(N⁺) blend polymer is an efficient adsorbent for removing anionic dyes from wastewater.

Chitosan-g-polyacrylonitrile ZnO nano-composite, synthesis and characterization as new and good adsorbent for Iron from groundwater

The highly poisonous, non-biodegradable heavy metals present serious concern in wastewater environmental sustainability and human health. Using adsorption is an effective technology for the treatment of this kind of water. Therefore, developing efficient and cost-effective adsorbents considers a significant and an emerging topic in the field the water purification. Chitosan grafted polyacrylonitrile (Cs-g-PAN) was facially fabricated via graft polymerization using ammonium persulfate (APS) as the initiator. The simple ultrasonic technique was used for doping ZnO nanoparticles into the Cs-g-PAN matrix to prepare chitosan-grafted polyacrylonitrile/ZnO (Cs-g-PAN/ZnO). For comparative study, pure ZnO and nanocomposite of PAN doped with ZnO (PAN/ZnO) were also prepared. XRD, FTIR, SEM, TEM, BET, EDS, and TGA measurements were conducted to confirm the morphological and structural properties of the prepared materials. Cs-g-PAN/ZnO possesses a specific surface area of 20.23 m²/g with a pore size of 31.58 nm and pore volume of 0.16 cm³ g^-1. The adsorption behavior toward Fe(II) as a pollutant for groundwater was studied for the synthesized materials. The effect of pH (4-8), contact time (5-60 min), adsorbent dose (0.01-0.3 g), and different temperature degrees (278, 288, 298, 308, and 318 K) on the removal of iron (II) has been conducted. The removal efficiency was achieved 100 % under the optimum condition, at pH = 7, contact time 30 min, adsorbate concentration 0.93 mg/L, and adsorbent dosage 0.05 g/L at room temperature. Langmuir and Freundlich's isothermal and kinetic studies have been analyzed to determine the adsorption mechanism of Fe(II) ions on the synthesized nanomaterials. The adsorption process of Fe(II) over the surface of prepared catalysts proceeded via the Langmuir model and pseudo-second-order reaction kinetics with R² > 0.99. Suggesting the formation of Fe(II) monolayer over the adsorbent surface and the rate-limiting step is probably controlled by chemisorption through sharing the electrons between Fe⁺² and the prepared catalyst.

Evaluation of acyclovir adsorption on granular activated carbon from aqueous solutions: batch and fixed-bed parametric studies

The present study is aimed to assess the adsorptive potential of carbonaceous material for the acyclovir (ACVR) removal from the aquatic environment using batch and fixed-bed processes. In batch mode, the impact of various process conditions (contact time, pH, adsorbent dose, initial ACVR concentration, and temperature) on ACVR adsorption was investigated. Experimental results revealed that Langmuir isotherm and the pseudo-second-order kinetic model adequately represent the ACVR adsorption mechanism, indicating homogeneous adsorption. The process was found exothermic and spontaneous. Thermodynamic studies concluded that adsorption is a result of both physisorption and chemisorption. To understand the dynamic regime for the design of large-scale column studies, experimental data obtained from breakthrough curve were fitted to various analytical kinetic models. Yan model followed by Thomas model demonstrated a greater correlation of breakthrough data, confirming that the results are significant and are in line with Langmuir isotherm and pseudo-second-order kinetic. G-AC exhibits sufficient adsorption capacity for ACVR. Hence, it is concluded that it can be used in a fixed-bed column in continuous mode for the treatment of ACVR-contaminated wastewater.

Graphical abstract

Supplementary Information

The online version contains supplementary material available at 10.1007/s11696-023-02810-7.

Relationship between white matter alterations and contamination subgroup in obsessive compulsive disorder: A diffusion tensor imaging study

Approximately 2%-3% of the world population suffers from obsessive-compulsive disorder (OCD). Several brain regions have been involved in the pathophysiology of OCD, but brain volumes in OCD may vary depending on specific OCD symptom dimensions. The study aims to explore how white matter structure changes in particular OCD symptom dimensions. Prior studies attempt to find the correlation between Y-BOCS scores and OCD patients. However, in this study, we separated the contamination subgroup in OCD and compared directly to healthy control to find regions that exactly related to contamination symptoms. To evaluate structural alterations, diffusion tensor imaging was acquired from 30 OCD patients and 34 demographically matched healthy controls. Data were processed using tract-based spatial statistics (TBSS) analysis. First, by comparing all OCD to healthy controls, significant fractional anisotropy (FA) decreased in the right anterior thalamic radiation, right corticospinal tract, and forceps minor observed. Then by comparing the contamination subgroup to healthy control, FA decreases in the forceps minor region. Consequently, forceps minor plays a central role in the pathophysiology of contamination behaviors. Finally, other subgroups were compared to healthy control and discovered that FA in the right corticospinal tract and right anterior thalamic radiation is reduced.

Novel polyamide/silica/chitosan covalent hybrid: One-step BIC/sol-gel preparation at room temperature and dual applications in Hg2+ electrochemical probing and dye adsorption

Room-temperature preparation of polymer-based covalent hybrids, which with multiple functional characteristics, is instrumental to overcome the performance shortcomings of single-polymer materials and broaden their applications thus. Herein, by introducing chitosan (CS) as a starting substrate into benzoxazine-isocyanide chemistry (BIC)/sol-gel reaction system, a novel polyamide (PA)/SiO₂/CS covalent hybrid (PA-Si-CS) was successfully prepared in-situ at 30 °C. PA-Si-CS's chemical structure and elementary properties were characterized here. The introduction of CS combining with the presence of diverse N, O-containing segments (amide, phenol -OH, Si-OH, etc.) in PA-Si-CS provided its synergistic adsorption for Hg²⁺ and anionic dye Congo red (CR). The capture of PA-Si-CS for Hg²⁺ was rationally applied to the "enrichment"-type electrochemical probing of Hg²⁺. Relevant detection range, detection limit, interference, and probing mechanism were systematically analyzed. Compared with the experimental results of control electrodes, the electrode modified with PA-Si-CS (PA-Si-CS/GCE) showed a significantly enhanced electrochemical response to Hg²⁺, with a detection limit up to ~2.2 × 10^-8 mol/L. In addition, PA-Si-CS also exhibited the specific adsorption for CR. Systematic analyses of dye adsorption selectivity, kinetics, isothermal models, thermodynamics, and adsorption mechanism told that PA-Si-CS can be used as an efficient CR adsorbent, with a maximum adsorption capacity of ~348 mg/g.

Synthesis, characterization and application of chitosan/graphene oxide/copper ferrite nanocomposite for the adsorptive removal of anionic and cationic dyes from wastewater

The increased discharge of water pollutants drives the development of new and effective wastewater remediation methods. Herein, a magnetic nanocomposite of chitosan-graphene oxide (GO) decorated with copper ferrite (MCSGO) was synthesized under ultrasound agitation and applied to the effective removal of Safranin O (SAF) and indigo carmine (IC) dyes from wastewater. The structural, magnetic, and physicochemical features of the as-prepared MCSGO nanocomposite have been thoroughly investigated using various characterization techniques. The operational parameters such as MCSGO mass, contact time, pH, and initial dye concentration were investigated. The effects of diverse coexisting species on both dye elimination processes were examined. The experimental results demonstrated that the adsorption capacity of MCSGO nanocomposite for IC and SAF was 112.6 and 66.15 mg g^-1, respectively. Five different adsorption isotherms were investigated using two-parameter (Langmuir, Tekman, and Freundlich) and three-parameter (Sips, and Redlich-Peterson) models. Thermodynamic studies revealed that the elimination of both dyes on MCSGO nanocomposite was endothermic and spontaneous, with anionic and cationic dye molecules randomly arranged onto the adsorbent nanoparticles. Moreover, the mechanism of dye elimination was deduced. Furthermore, even after five cycles of adsorption and desorption, the as-prepared nanocomposite showed no significant loss in the dye removal efficiency, indicating that it has superior stability and recycling potential.

Reduced Graphene Oxide-Zinc Sulfide Nanocomposite Decorated with Silver Nanoparticles for Wastewater Treatment by Adsorption, Photocatalysis and Antimicrobial Action

Reduced graphene oxide nanosheets decorated with ZnS and ZnS-Ag nanoparticles are successfully prepared via a facile one-step chemical approach consisting of reducing the metal precursors on a rGO surface. Prepared rGO-ZnS nanocomposite is employed as an adsorbent material against two model dyes: malachite green (MG) and ethyl violet (EV). The adsorptive behavior of the nanocomposite was tuned by monitoring some parameters, such as the time of contact between the dye and the adsorbent, and the adsorbent dose. Experimental data were also simulated with kinetic models to evaluate the adsorption behavior, and the results confirmed that the adsorption of both dyes followed a pseudo 2nd order kinetic mode. Moreover, the adsorbent was also regenerated in a suitable media for both dyes (HCl for MG and ethanol for EV), without any significant loss in removal efficiency. Ag doped rGO-ZnS nanocomposite was also utilized as a photocatalyst for the degradation of the selected organic contaminant, resorcinol. The complete degradation of the phenolic compound was achieved after 60 min with 200 mg of rGO-ZnS-Ag nanocomposite under natural sunlight irradiation. The photocatalytic activity was studied considering some parameters, such as the initial phenol concentration, the photocatalyst loading, and the pH of the solution. The degradation kinetics of resorcinol was carefully studied and found to follow a linear Langmuir-Hinshelwood model. An additional advantage of rGO-ZnS and rGO-ZnS-Ag nanocomposites was antibacterial activity against Gram-negative bacterium, E. coli, and the results confirmed the significant performance of the nanocomposites in destroying harmful pathogens.

Nanomaterials as a Sustainable Choice for Treating Wastewater: A Review

The removal of dyes from textile effluents utilizing advanced wastewater treatment methods with high efficiency and low cost has received substantial attention due to the rise in pollutants in water. The purpose of this work is to give a comprehensive analysis of the different treatments for removing chemical dyes from textile effluents. The capability and potential of conventional treatments for the degradation of dyeing compounds in aqueous media, as well as the influence of multiple parameters, such as the pH solution, initial dye concentration, and adsorbent dose, are presented in this study. This study is an overview of the scientific research literature on this topic, including nanoreductive and nanophotocatalyst processes, as well as nanoadsorbents and nanomembranes. For the purpose of treating sewage, the special properties of nanoparticles are currently being carefully researched. The ability of nanomaterials to remove organic matter, fungus, and viruses from wastewater is another benefit. Nanomaterials are employed in advanced oxidation techniques to clean wastewater. Additionally, because of their small dimensions, nanoparticles have a wide effective area of contact. Due to this, nanoparticles' adsorption and reactivity are powerful. The improvement of nanomaterial technology will be beneficial for the treatment of wastewater. This report also offers a thorough review of the distinctive properties of nanomaterials used in wastewater treatment, as well as their appropriate application and future possibilities. Since only a few types of nanomaterials have been produced, it is also important to focus on their technological feasibility in addition to their economic feasibility. According to this study, nanoparticles (NPs) have a significant adsorption area, efficient chemical reactions, and electrical conductivity that help treat wastewater effectively.

Recent Advances in the Synthesis, Characterization, and Application of Carbon Nanomaterials for the Removal of Endocrine-Disrupting Chemicals: A Review

The large-scale production and frequent use of endocrine-disrupting chemicals (EDCs) have led to the continuous release and wide distribution of these pollutions in the natural environment. At low levels, EDC exposure may cause metabolic disorders, sexual development, and reproductive disorders in aquatic animals and humans. Adsorption treatment, particularly using nanocomposites, may represent a promising and sustainable method for EDC removal from wastewater. EDCs could be effectively removed from wastewater using various carbon-based nanomaterials, such as carbon nanofiber, carbon nanotubes, graphene, magnetic carbon nanomaterials, carbon membranes, carbon dots, carbon sponges, etc. Important applications of carbon nanocomposites for the removal of different kinds of EDCs and the theory of adsorption are discussed, as well as recent advances in carbon nanocomposite synthesis technology and characterization technology. Furthermore, the factors affecting the use of carbon nanocomposites and comparisons with other adsorbents for EDC removal are reviewed. This review is significant because it helps to promote the development of nanocomposites for the decontamination of wastewater.

Identifying and tailoring C–N coupling site for efficient urea synthesis over diatomic Fe–Ni catalyst

Electrocatalytic urea synthesis emerged as the promising alternative of Haber–Bosch process and industrial urea synthetic protocol. Here, we report that a diatomic catalyst with bonded Fe–Ni pairs can significantly improve the efficiency of electrochemical urea synthesis. Compared with isolated diatomic and single-atom catalysts, the bonded Fe–Ni pairs act as the efficient sites for coordinated adsorption and activation of multiple reactants, enhancing the crucial C–N coupling thermodynamically and kinetically. The performance for urea synthesis up to an order of magnitude higher than those of single-atom and isolated diatomic electrocatalysts, a high urea yield rate of 20.2 mmol h⁻¹ g⁻¹ with corresponding Faradaic efficiency of 17.8% has been successfully achieved. A total Faradaic efficiency of about 100% for the formation of value-added urea, CO, and NH₃ was realized. This work presents an insight into synergistic catalysis towards sustainable urea synthesis via identifying and tailoring the atomic site configurations.

The direct electrocatalytic synthesis of urea via C–N coupling is of great significance. The authors report a diatomic catalyst with bonded Fe–Ni pairs to improve the efficiency of electrochemical urea synthesis from nitrate and CO₂.

Adsorption of methylene blue by Nicandra physaloides(L.) Gaertn seed gum/graphene oxide aerogel

In this study, a novel composite aerogel of Nicandra physaloides(L.) Gaertn seed, gum/graphene oxide (NPG/GO), was prepared by using a vacuum freeze drying method for methylene blue (MB) adsorption. The techniques, including Brunauer-Emmett-Teller (BET), scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR), were adopted for studying the structure and surface characteristics of NPG/GO, with thermogravimetric analysis (TGA) being adopted for testing thermal properties. The effects of pH value, initial dye concentration, temperature and adsorbent dosage on adsorption performance were elaborately analysed. The adsorption kinetic studies showed that the process of adsorption follows Langmuir isotherm and a pseudo-second-order kinetic model. When the mass ratio of NPG to GO was 1.25:1, the adsorption capacity was the highest. According to Langmuir isotherm, the maximum adsorption capacity of 408.16 mg/g was higher than that of NPG. The specific surface area and average pore diameter of NPG/GO was measured as 2.70 m²/g and 4.8 nm, respectively. Thermodynamic analysis revealed that the adsorption process of methylene blue on NPG/GO was a spontaneous and endothermic process. In general, the prepared nanocomposites were excellent candidates for adsorption and removal process because of simple synthesis, low cost, high efficiency, non-toxicity, environment protection and degradability.

Graphene Oxide-Chitosan Network on a Dialysis Cellulose Membrane for Efficient Removal of Organic Dyes

Currently, water pollution is a significant health problem for both humans and animals due to large amounts of dye-containing wastewater. Thus, polymer composite membranes (PCMs) are considered as efficient adsorption/filtration membranes that can be utilized for removing organic dyes from contaminated water/wastewater. In this study, the goal is to explore the modification of the interfacial dialysis cellulose (DC) surface through molecular interactions of an active graphene oxide-chitosan (GO-CTS) composite hydrogel (GCCH) network without the use of an external cross-linker toward an effective dye removal ability using a simple casting process and a low-cost adsorption technique, resulting in the formation of a PCM, i.e., GO/CTS/DC membrane (GCD-mems). Concomitantly, the incorporation of the GCCH network (as an active hybrid network) and DC (as a supporting material) is considered as a promising approach toward a dye-removing PCM. As a result, the GCD-mems showed that cellulose robustly interacted via the chemical bonds of the GCCH network by maintaining the three-dimensional (3D) porous layer structures, and the functional surface of the membrane was enhanced toward specific groups for an effective dye removal approach. In addition, there is a significant improvement in dye removal performance after modification of the interfacial DC surface through molecular interactions of GCCH, i.e., high adsorption capacities of cationic and anionic dye molecules on the GCD-mems, compared to the relevant GO-based adsorbents. Also, the dye flux and rejection of the GCD-mems can simultaneously remove both methylene blue and Congo red. In the adsorption, it is appropriate with the pseudo-second-order and Langmuir models corresponding to chemical adsorption and monolayer approaches, as well as physical sieving through the 3D layers of porous channels of GCD-mems during the filtration process. Moreover, the structural stability and sustainability of the PCMs are enhanced during the recycling process, and the use of ethanol in the recycling process further simplifies the process and reduces the cost of the PCMs. Thus, the GCD-mems are encouraged as potential candidates that can be applied directly in the removal of dyes from the wastewater of textile industries or selective dialysis applications.

Recent advances and perspectives of g-C3N4-based materials for photocatalytic dyes degradation

Photocatalytic degradation technology is regarded as a promising technology for dye-contained wastewater treatment due to its superior efficiency and recycling. The key to the implementation of photocatalytic degradation technology is the selection of sunlight-active photocatalyst. Graphitic carbon nitride (g-C₃N₄) photocatalyst has been put into a lot of research in the field of organic pollutant degradation because of its low cost, suitable electronic structure and high chemical stability. In this perspective review, we comprehensively discuss the recent advance of photocatalytic dyes degradation over g-C₃N₄-based materials. The properties, structure and preparation methods of g-C₃N₄ are briefly introduced. Furthermore, the progress in improving the degradation efficiency of g-C₃N₄-based photocatalyst is highlighted in the article. The possible pathways and different active species for dyes decomposition are also summarized. We expect this review can provide instructive application of g-C₃N₄-based catalysts for environmental remediation.

Utilization of a double-cross-linked amino-functionalized three-dimensional graphene networks as a monolithic adsorbent for methyl orange removal: Equilibrium, kinetics, thermodynamics and artificial neural network modeling

Herein, it is aimed to develop a high-performance monolithic adsorbent to be utilized in methyl orange (MO) adsorption. Therefore, amino-functionalized three-dimensional graphene networks (3D-GN_f) fulfilling the requirements of reusability and high capacity have been fabricated via hydrothermal self-assembly approach followed by a double-crosslinking strategy. The potential utilization of 3D-GN_f as an adsorbent for removal MO has been assessed using both batch-adsorption studies and an artificial neural network (ANN) approach. Graphene oxide sheets have been amino-functionalized and cross-linked, by ethylenediamine (EDA) during hydrothermal treatment, following the glutaraldehyde has used as a double-crosslinking agent to facilitate the crosslinking of architecture. The successful fabrication of 3D-GN_f has been confirmed by field-emission scanning electron microscopy (FESEM), Fourier transform infrared (FT-IR), Raman and X-ray photoelectron spectroscopy (XPS). Moreover, N₂ adsorption/desorption isotherms have revealed the high specific surface area (1015 m² g^-1) with high pore volume (1.054 cm³ g^-1) and hierarchical porous structure of 3D-GN_f. The effect of initial concentration, contact time, and temperature on adsorption capacity have been thoroughly studied, and the kinetics, isotherms, and thermodynamics of MO adsorption have been modelled. The MO adsorption has been well defined by the pseudo-second-order kinetic model and Langmuir isotherm model with a monolayer adsorption capacity of 270.27 mg g^-1 at 25 °C. The thermodynamic findings have revealed MO adsorption has occurred spontaneously with an endothermic process. The Levenberg-Marquardt backpropagation algorithm has been implemented to train the ANN model, which has used the activation functions of tansig and purelin functions at the hidden and output layers, respectively. An optimum ANN model with high-performance metrics (coefficient of determination, R² = 0.9995; mean squared error, MSE = 0.0008) composed of three hidden layers with 5 neurons in each layer was constructed to forecast MO adsorption. The findings have shown that experimental results are consistent with ANN-based data, implying that the suggested ANN model may be used to forecast cationic dye adsorption.

Graphene oxide functionalized with cobalt ferrites applied to the removal of bisphenol A: ionic study, reuse capacity and desorption kinetics

A new adsorbent material based on graphene oxide (GO) functionalized with magnetic cobalt ferrite nanoparticles (γCoFe₂O₄) was synthesized via ultrasonication to remove the endocrine-disrupting-chemical bisphenol A (BPA) from aqueous solutions. The synthesized material (GO-γCoFe₂O₄) was characterized by TEM, SEM, DRX and FTIR analysis. Magnetization measures proved that the adsorbent had superparamagnetic characteristics that facilitated its separation from the aqueous solution. The maximum adsorption capacity obtained was 30 mg g^-1 with adsorbent concentration of 1 g L^-1, temperature of 55°C and natural pH of the solution. The experimental data were better adjusted to the kinetic models of pseudo-second-order and Langmuir isotherm. The thermodynamic parameters showed that the BPA adsorption on GO-γCoFe₂O₄ was spontaneous, exothermic and thermodynamically favourable. Desorption kinetics was performed using 50% ethanol as solvent, resulting in an equilibrium time of 4 h with better adjustment to the pseudo-second order kinetic model. The adsorbent showed a high regeneration capacity maintaining adsorptive capacity above 75% after 6 cycles of reuse.

Epichlorohydrin and tripolyphosphate-crosslinked chitosan-kaolin composite for Auramine O dye removal from aqueous solutions: Experimental study and DFT calculations

Chitosan (Ch, a natural polymer) and kaolin (K, a natural mineral) composite (Ch-K) was produced with the help of two crosslinkers, epichlorohydrin and tripolyphosphate, and then moulded into uniform beads in tripolyphosphate solution. The synthesis was proved by the analyses involving FT-IR and SEM-EDX. The beads were then used as the natural adsorbent for removal of the auramine O (AO), a frequently-used industrial dye, in aqueous solutions. Adsorbent performance of the Ch-K composite for AO dye molecules was optimized: 500 mg L^-1 at pH 7.5 at 25 °C. The Langmuir model found 0.118 mol kg^-1 for the maximum adsorption capacity of the Ch-K and the D-R isotherm model showed that the nature of the adsorption process was physical. Kinetics of the adsorption could be explained by using both IPD (intraparticle diffusion) and PSO (pseudo second order) models. Thermodynamic parameters demonstrated that the behaviour of the adsorption was an endothermic and spontaneous. The activity of the composite adsorbent was recovered (88%) after the five sequential adsorption/desorption cycles. Supported by experimental findings, the results obtained from in silico modeling at M06-2X/6-31+G (d,p) level helped hypothesise a mechanism for the formation of the Ch-K composite, and shed some light onto the adsorption behaviour of AO dye by assuming several favourable intermolecular interactions.

Application of MXenes for water treatment and energy-efficient desalination: A review

MXenes are a new type of two-dimensional (2D) material which are rapidly gaining traction for a range of environmental, chemical and medical applications. MXenes and MXene-composites exhibit high surface area, superlative chemical stability, thermal conductivity, hydrophilicity and are environmentally compatible. Consequently, MXenes have been successfully employed for hydrogen storage, semiconductor manufacture and lithium ion batteries. In recent years, MXenes have been utilized in numerous environmental applications for treating contaminated surface waters, ground and industrial/ municipal wastewaters and for desalination, often outperforming conventional materials in each field. MXene-composites can adsorb multiple organic and inorganic contaminants, and undergo Faradaic capacitive deionization (CDI) when utilized for electrochemical applications. This approach allows for a significant decrease in the energy demand by overcoming the concentration polarization limitation of conventional CDI electrodes, offering a solution for low-energy desalination of brackish waters. This article presents a state-of-the-art review on water treatment and desalination applications of MXenes and MXene-composites. An investigation into the kinetics and isotherms is presented, as well as the impact of water constituents and operating conditions are also discussed. The applications of MXenes for CDI, pervaporation desalination and solar thermal desalination are also examined based on the reviewed literature. The effects of the water composition and operational protocols on the regeneration efficacy and long-term usage are also highlighted.

Silk Sericin Enrichment through Electrodeposition and Carbonous Materials for the Removal of Methylene Blue from Aqueous Solution

The recycling and reuse of biomass waste for the preparation of carbon-based adsorbents is a sustainable development strategy that has a positive environmental impact. It is well known that a large amount of silk sericin (SS) is dissolved in the wastewater from the silk industry. Utilizing the SS instead of discharging it into the environment without further treatment would reduce environmental and ecological problems. However, effective enrichment of the SS from the aqueous solution is a challenge. Here, with the help of carboxymethyl chitosan (CMCS), which can form a gel structure under low voltage, an SS/CMCS hydrogel with SS as the major component was prepared via electrodeposition at a 3 V direct-current (DC) voltage for five minutes. Following a carbonization process, an SS-based adsorbent with good performance for the removal of methylene blue (MB) from an aqueous solution was prepared. Our results reveal that the SS/CMCS hydrogel maintains a porous architecture before and after carbonization. Such structure provides abundant adsorption sites facilitating the adsorption of MB molecules, with a maximum adsorptive capacity of 231.79 mg/g. In addition, it suggests that the adsorption is an exothermic process, has a good fit with the Langmuir model, and follows the intra-particle diffusion model. The presented work provides an economical and feasible path for the treatment of wastewater from dyeing and printing.

A versatile EDTA and chitosan bi-functionalized magnetic bamboo biochar for simultaneous removal of methyl orange and heavy metals from complex wastewater

At present, the simultaneous removal of organic dyes and heavy metals in complex wastewater has raised considerable concern, owing to their striking differences in physicochemical properties. Adsorption, as one of the few removal methods, has attracted extensive attention and gained popularity. Herein, a versatile EDTA and chitosan bi-functionalized magnetic bamboo biochar adsorbent (ECMBB) was synthesized for coinstantaneous adsorption of methyl orange (MO) and heavy metals (Cd(II) and Zn(II)). In this case, the as-synthesized ECMBB composites inherited favorable anionic MO removal performance from bamboo biochar (BB) obtained at 700 °C through electrostatic attraction, hydrogen bonding and π-π interaction, also enhanced the binding of cationic metals by introducing amino groups of chitosan and carboxyl groups of EDTA. In the unitary system, the removal of MO, Cd(II) and Zn(II) by three as-prepared adsorbents can be well illuminated by pseudo-second-order kinetic model and Langmuir isotherm theory. The saturated capture amounts of ECMBB at 25 °C are 305.4 mg g^-1 for MO, 63.2 mg g^-1 for Cd(II) and 50.8 mg g^-1 for Zn(II), which, under the same conditions, are 1.3, 2.6 and 2.5 times those of chitosan-modified magnetic bamboo biochar (CMBB) and 1.9, 6.1 and 5.4 times those of magnetic bamboo biochar (MBB), respectively. Remarkably, in MO-metal binary system, coexisting MO visibly enhanced the adsorption of Cd(II) and Zn(II), while coexisting heavy metals had no significant impact on MO adsorption. Furthermore, ECMBB exhibited no significant loss in adsorption efficiency even after eight adsorption-desorption experiments. This study lays the foundation for fabricating desired integrative biochar adsorbents in the simultaneous purification of organic and metallic pollutants from complex wastewater.

Simultaneous adsorption for cationic and anionic dyes using chitosan/electrospun sodium alginate nanofiber composite sponges

The coexistence of anionic and cationic dyes in dye wastewater has highlighted a great necessity to develop amphoteric adsorbents for their simultaneous removal. Herein, an amphoteric composite sponge was successfully fabricated by combining chitosan with electrospun sodium alginate nanofiber using lyophilization in acetic acid/water/dioxane mixed solvents, which owned the abundant functional groups and superior microstructure of interconnected pores and nanoscale fibers, beneficial for the adsorption capacity improvement. The optimum adsorption capacities for Acid Blue-113 and Rhodamine B were 926.2 ± 25.7 mg/g and 695.4 ± 17.0 mg/g, respectively, much higher than that of the controlled sample prepared with chitosan and non-spinning sodium alginate in traditional acetic acid/water solvents. Meanwhile, the sponge provided with the superior adsorption performance under various pH environment and cyclic adsorption. Importantly, it had considerable simultaneous adsorption capacity for binary system containing anionic and cationic dyes. Overall, the chitosan/electrospun sodium alginate nanofiber composite sponge shows potential for complex wastewater treatment.

Removal of methylene blue from wastewater using ternary nanocomposite aerogel systems: Carboxymethyl cellulose grafted by polyacrylic acid and decorated with graphene oxide

In this study, environmentally-friendly nanocomposite hydrogels were fabricated. These hydrogels consisted of semi-interpenetrating networks of carboxymethyl cellulose (CMC) molecules grafted to polyacrylic acid (PAA), as an eco-friendly and non-toxic polymer with numerous carboxyl and hydroxyl functional groups, which were reinforced with different levels of graphene oxide particles (0.5, 1.5 or 3% wt). Field-emission electron scanning microscopy (FESEM) images indicated that the pore size of the nanocomposites decreased with increasing graphic oxide concentration. The presence of the graphic oxide increased the storage modulus and thermal stability of the nanocomposite hydrogels. The hydrogels had an adsorption capacity of 138 mg/g of a model cationic dye pollutant (methylene blue) after 250 min. Moreover, a reusability test showed that the adsorption capacity remained at around 90% after 9 cycles. Density functional theory (DFT) simulations suggested that the adsorption of methylene blue was mainly a result of π-π bonds, hydrogen bonds, and electrostatic interactions with graphene oxide. Our results indicated that the nanocomposite hydrogels fabricated in this study may be eco-friendly, stable, efficient, and reusable adsorbents for ionic pollutants in wastewater treatment.

Synthesis of amorphous carbon functionalized Fe3O4 nanoparticles as a smart nanosorbent for organic dyes removal

Illustration of process for synthesis of carbon coated Fe3O4 (CCF) nanocomposites and their application as nanosorbents with recoverability and regenerability for the sorption of organic dyes.

Recent progress, synthesis, and applications of chitosan-decorated magnetic nanocomposites in remediation of dye-laden wastewaters

Over the past several decades, the disposal of dyes from the industrial manufacturing sector has had an inadvertent impact on water ecology as polluted water bodies with these hazardous dyes...