Biotechnological strategies for the recovery of valuable and critical raw materials from waste electrical and electronic equipment (WEEE) - A review

Assessment of direction changes in waste electrical and electronic equipment management in Poland

A growing amount of waste electrical and electronic equipment (WEEE) indicates the need to verify the effectiveness of its management both nationally and globally. An analysis of the WEEE economy in Poland conducted over 5 years confirmed a 16.64% increase in the mass of collected equipment. The maximum annual mass of electrical and electronic equipment introduced to the market during this period was 607,240 Mg, with the average value exceeding 500,000 Mg. The WEEE category with the largest collected mass was waste code 20 01 36, which exceeded 235,000 Mg, whilst the highest waste weight accumulation rate of 45.98 kg per capita was recorded in one of the smallest voivodeships in Poland. This result showed the diversity of WEEE accumulation on a national scale. Overall, a noticeable increase in the WEEE accumulation rate has occurred as Poland's gross domestic product has increased, despite a decreasing population. An analysis based on the waste accumulation indicators, including socioeconomic factors, confirmed the need to develop forms of WEEE recovery and recycling to transition to a circular economy and promote the synergy of activities amongst all players in WEEE management.

Selective leaching of indium from spent LCD screens by siderophore desferrioxamine E

Given the criticality of indium (In) in high-tech applications, spent LCD screens can represent a viable secondary In resource. In this work, an innovative and alternative technology to selectively leach In from spent LCD screens using a microbial chelating agent, desferrioxamine E (DFOE), was developed. Indium was concentrated from spent LCD screens by implementing an adapted pre-treatment procedure, allowing the isolation of an indium-rich glassy fraction. During leaching, the competition between aluminum (Al) and In for complexation with DFOE leads to the precipitation of In(OH)3 at low DFOE concentrations (12-240 µM). After adjusting the optimal conditions (fraction size: 0-36 μM, pH: 5.5, S/L ratio: 1 g/L, 25 °C), the In leaching yield reached 32%, ten times higher than Al over 90 days with 5 mM DFOE. Thus, achieving high In recovery is possible through i) prolonging leaching durations, ii) selective leaching, and iii) minimizing Al interference. This is the first attempt to selectively leach In using a selected siderophore from end-of-life products with high concentrations of non-targeted elements (i.e. Al, Si, and Ca). This study demonstrates the potential of generating indium-rich leachates, which can be subsequently processed through the GaLIophore technology for In refining.

Microbial recovery of rare earth elements from various waste sources: a mini review with emphasis on microalgae

Rare Earth Elements (REEs) are indispensable in contemporary technologies, influencing various aspects of our daily lives and environmental solutions. The escalating demand for REEs has led to increased exploitation, resulting in the generation of diverse REE-bearing solid and liquid wastes. Recognizing the potential of these wastes as secondary sources of REEs, researchers are exploring microbial solutions for their recovery. This mini review provides insights into the utilization of microorganisms, with a particular focus on microalgae, for recovering REEs from sources such as ores, electronic waste, and industrial effluents. The review outlines the principles and distinctions of bioleaching, biosorption, and bioaccumulation, offering a comparative analysis of their potential and limitations. Specific examples of microorganisms demonstrating efficacy in REE recovery are highlighted, accompanied by successful methods, including advanced techniques for enhancing microbial strains to achieve higher REE recovery. Moreover, the review explores the environmental implications of bio-recovery, discussing the potential of these methods to mitigate REE pollution. By emphasizing microalgae as promising biotechnological candidates for REE recovery, this mini review not only presents current advances but also illuminates prospects in sustainable REE resource management and environmental remediation.

Advances in bio/chemical approaches for sustainable recycling and recovery of rare earth elements from secondary resources

Rare Earth Elements (REEs) are indispensable in the growing smart technologies, such as smart phones and electronic devices, renewable energy, new generation of hybrid cars, etc. These elements are naturally occurring in specific geological deposits (bastnäsite, monazite, and xenotime), primarily concentrated in the regions of China, Australia, and the USA. The extraction and processing of REEs and the mismanagement of secondary REE resources, such as industrial waste, end-of-life materials, and mining by-products, raise major environmental and health concerns. Recycling represents a convincing solution, avoiding the necessity to separate low-value or coexisting radioactive elements when REEs are recovered from raw ore. Despite these advantages, only 1 % of REEs are usually recycled. This review overreached strategies for recycling REEs from secondary resources, emphasizing their pivotal role. The predominant approach for recycling REEs involves hydrometallurgical processing by leaching REEs from their origins using acidic solutions and then separating them from dissolved impurities using techniques like liquid-liquid extraction, membrane separation, chromatography, adsorption, flotation, and electrochemical methods. However, these methods have notable disadvantages, particularly their over requirements for water, reagents, and energy. Biohydrometallurgy introduces an innovative alternative using microorganisms and their metabolites to extract REEs through bioleaching. Other investigations are carried out to recover REEs through biological strategies, including biosorption, affinity chromatography with biological ligands, bioflotation employing biological surfactants, and bioelectrochemical methods. However, biohydrometallurgical processes can also be relatively slow and less suitable for large-scale applications, often lacking specificity for targeted REEs recovery. Overcoming these challenges necessitates ongoing research and development efforts to advance recycling technologies.

Recovery of precious metals from waste printed circuit boards though bioleaching route: A review of the recent progress and perspective

The rapid proliferation of electronic waste (e-waste), including waste printed circuit boards (WPCBs), has exerted immense pressure on the environment. The recovery of precious metals from WPCBs not only serves as an effective means of alleviating this environmental burden but also generates economic value. This review focuses on bioleaching, an environmentally friendly method for extracting precious metals from WPCBs. Under various conditions, this method has achieved leaching rates of 30%-73% for Au and 33.8%-90% for Ag. However, there is a relative scarcity of studies on the bioleaching of precious metals from WPCBs. In this paper, we provide an overview of the current status of bioleaching for precious metals from WPCBs and describe the underlying mechanisms. We also briefly outline the influence of various process factors on leaching efficiency. While this review underscores the considerable potential of bioleaching in WPCBs applications, certain limitations hinder the engineering-scale application of the technology. Consequently, this paper describes the current enhanced processes for enhancing leaching efficiency. Overall, this review can serve as a valuable reference for future research endeavors, ultimately promoting the widespread utilization of bioleaching for the recovery of precious metals from WPCBs.

Recovery technologies for indium, gallium, and germanium from end-of-life products (electronic waste) - A review

Advanced high-tech applications for communication, renewable energy, and display, heavily rely on technology critical elements (TCEs) such as indium, gallium, and germanium. Ensuring their sustainable supply is a pressing concern due to their high economic value and supply risks in the European Union. Recovering these elements from end-of-life (EoL) products (electronic waste: e-waste) offers a potential solution to address TCEs shortages. The review highlights recent advances in pre-treatment and hydrometallurgical and biohydrometallurgical methods for indium, gallium, and germanium recovery from EoL products, including spent liquid crystal displays (LCDs), light emitting diodes (LEDs), photovoltaics (PVs), and optical fibers (OFs). Leaching methods, including strong mineral and organic acids, and bioleaching, achieve over 95% indium recovery from spent LCDs. Recovery methods emphasize solvent extraction, chemical precipitation, and cementation. However, challenges persist in separating indium from other non-target elements like Al, Fe, Zn, and Sn. Promising purification involves solid-phase extraction, electrochemical separation, and supercritical fluid extraction. Gallium recovery from spent GaN and GaAs LEDs achieves 99% yield via leaching with HCl after annealing and HNO3, respectively. Sustainable gallium purification techniques include solvent extraction, ionic liquid extraction, and nanofiltration. Indium and gallium recovery from spent CIGS PVs achieves over 90% extraction yields via H2SO4 with citric acid-H2O2 and alkali. Although bioleaching is slower than chemical leaching (several days versus several hours), indirect bioleaching shows potential, achieving 70% gallium extraction yield. Solvent extraction and electrolysis exhibit promise for pure gallium recovery. HF or alkali roasting leaches germanium with a high yield of 98% from spent OFs. Solvent extraction achieves over 90% germanium recovery with minimal silicon co-extraction. Solid-phase extraction offers selective germanium recovery. Advancements in optimizing and implementing these e-waste recovery protocols will enhance the circularity of these TCEs.

Recycling and reutilization of smelting dust as a secondary resource: A review

Smelting dust is a toxic waste produced in metal-mineral pyrometallurgical processes. To eliminate or reduce the adverse environmental impacts of smelting dust, valuable components need to be selectively separated from the toxic components present in the waste. This paper reviews the chemical composition, phase composition and particle size distribution characteristics of smelting dust, and the results show that smelting dust has excellent physicochemical characteristics for recovering valuable metals. The process flow, critical factors, development status, advantages and disadvantages of traditional technologies such as pyrometallurgy, hydrometallurgy and biometallurgy were discussed in depth. Conventional treatment methods typically prioritize separating and reclaiming specific elements with high concentrations. However, these methods face challenges such as excessive chemical usage and limited selectivity, which can hinder the sustainable utilization of smelting dust. With the increasing scarcity of resources and strict environmental requirements, a single treatment process can hardly fulfil the demand, and a physical field-enhanced technology for releasing and separating valuable metals is proposed. Through analysing the effect of electric field, microwave and ultrasound on recovering valuable metals from smelting dust, the enhancement mechanism of physical field on the extraction process was clarified. This paper aimed to provide reference for the resource utilization of smelting dust.

Zinc recovery from bioleachate using a microbial electrolysis cell and comparison with selective precipitation

Metal recycling is essential for strengthening a circular economy. Microbial leaching (bioleaching) is an economical and environmentally friendly technology widely used to extract metals from insoluble ores or secondary resources such as dust, ashes, and slags. On the other hand, microbial electrolysis cells (MECs) would offer an energy-efficient application for recovering valuable metals from an aqueous solution. In this study, we investigated a MEC for Zn recovery from metal-laden bioleachate for the first time by applying a constant potential of -100 mV vs. Ag/AgCl (3 M NaCl) on a synthetic wastewater-treating bioanode. Zn was deposited onto the cathode surface with a recovery efficiency of 41 ± 13% and an energy consumption of 2.55 kWh kg-1. For comparison, Zn recovery from zinc sulfate solution resulted in a Zn recovery efficiency of 100 ± 0% and an energy consumption of 0.70 kWh kg-1. Furthermore, selective metal precipitation of the bioleachate was performed. Individual metals were almost completely precipitated from the bioleachate at pH 5 (Al), pH 7 (Zn and Fe), and pH 9 (Mg and Mn).

Perspective on the use of methanogens in lithium recovery from brines

Methanogenic archaea stand out as multipurpose biocatalysts for different applications in wide-ranging industrial sectors due to their crucial role in the methane (CH4) cycle and ubiquity in natural environments. The increasing demand for raw materials required by the manufacturing sector (i.e., metals-, concrete-, chemicals-, plastic- and lubricants-based industries) represents a milestone for the global economy and one of the main sources of CO2 emissions. Recovery of critical raw materials (CRMs) from byproducts generated along their supply chain, rather than massive mining operations for mineral extraction and metal smelting, represents a sustainable choice. Demand for lithium (Li), included among CRMs in 2023, grew by 17.1% in the last decades, mostly due to its application in rechargeable lithium-ion batteries. In addition to mineral deposits, the natural resources of Li comprise water, ranging from low Li concentrations (seawater and freshwater) to higher ones (salt lakes and artificial brines). Brines from water desalination can be high in Li content which can be recovered. However, biological brine treatment is not a popular methodology. The methanogenic community has already demonstrated its ability to recover several CRMs which are not essential to their metabolism. Here, we attempt to interconnect the well-established biomethanation process with Li recovery from brines, by analyzing the methanogenic species which may be suitable to grow in brine-like environments and the corresponding mechanism of recovery. Moreover, key factors which should be considered to establish the techno-economic feasibility of this process are here discussed.

Embracing the future of circular bio-enabled economy: unveiling the prospects of microbial fuel cells in achieving true sustainable energy

Sustainable development and energy security, highlighted by the United Nations Sustainable Development Goals (SDGs), necessitate the use of renewable and sustainable energy sources. However, upon careful evaluation of literature, we have discovered that many existing and emerging renewable energy systems (RESs) prioritize renewability over true sustainability. These systems not only suffer from performance inconsistencies and lack of scalability but also fall short in fully embodying the principles of sustainability and circular economy. To address this gap, we propose considering microbial fuel cells (MFCs) as a viable alternative and integral part of the renewable energy ecosystem. MFCs harness the omnipresence, abundance, and cost-effectiveness of their essential components, making them a promising candidate. Through our comprehensive analysis, we shed light on the limitations and advancements of this technology, which underscore the remarkable potential of MFCs to revolutionize our perception of clean, sustainable energy.

Recovery of valuable metals from spent lithium-ion batteries using microbial agents for bioleaching: a review

Spent lithium-ion batteries (LIBs) are increasingly generated due to their widespread use for various energy-related applications. Spent LIBs contain several valuable metals including cobalt (Co) and lithium (Li) whose supply cannot be sustained in the long-term in view of their increased demand. To avoid environmental pollution and recover valuable metals, recycling of spent LIBs is widely explored using different methods. Bioleaching (biohydrometallurgy), an environmentally benign process, is receiving increased attention in recent years since it utilizes suitable microorganisms for selective leaching of Co and Li from spent LIBs and is cost-effective. A comprehensive and critical analysis of recent studies on the performance of various microbial agents for the extraction of Co and Li from the solid matrix of spent LIBs would help for development of novel and practical strategies for effective extraction of precious metals from spent LIBs. Specifically, this review focuses on the current advancements in the application of microbial agents namely bacteria (e.g., Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans) and fungi (e.g., Aspergillus niger) for the recovery of Co and Li from spent LIBs. Both bacterial and fungal leaching are effective for metal dissolution from spent LIBs. Among the two valuable metals, the dissolution rate of Li is higher than Co. The key metabolites which drive the bacterial leaching include sulfuric acid, while citric acid, gluconic acid and oxalic acid are the dominant metabolites in fungal leaching. The bioleaching performance depends on both biotic (microbial agents) and abiotic factors (pH, pulp density, dissolved oxygen level and temperature). The major biochemical mechanisms which contribute to metal dissolution include acidolysis, redoxolysis and complexolysis. In most cases, the shrinking core model is suitable to describe the bioleaching kinetics. Biological-based methods (e.g., bioprecipitation) can be applied for metal recovery from the bioleaching solution. There are several potential operational challenges and knowledge gaps which should be addressed in future studies to scale-up the bioleaching process. Overall, this review is of importance from the perspective of development of highly efficient and sustainable bioleaching processes for optimum resource recovery of Co and Li from spent LIBs, and conservation of natural resources to achieve circular economy.

Current overview and future perspective in fungal biorecovery of metals from secondary sources

Microorganisms are intimately involved in many biogeochemical processes that underpin the transformation of metals and cycling of related substances, such as metalloids and radionuclides. Many processes determine the mobility and bioavailability of metals, thereby influencing their transfer to the environment and living organisms. These processes are closely related to global phenomena such as soil formation and bioweathering. In addition to environmental significance, microbial metal transformations play an essential role in both in situ and ex situ bioremediation processes for solid and liquid wastes. The solubilization of heavy metals from industrial waste and soil is commonly used in bioremediation. Moreover, immobilization processes are applicable to bioremediation of metals and radionuclides from aqueous solutions. This review provides an overview of critical metal extraction and recovery from secondary sources, applied microorganisms and methods, metal-microbe interactions, as well as a detailed description of known metal recovery mechanisms.

A first comprehensive estimate of electronic waste in Canada

Detailed analysis of electronic waste (e-waste) generation and composition is of utmost importance for the proper management of growing e-waste stream worldwide, containing both hazardous and valuable materials. Considering the absence of such comprehensive and up-to-date studies in Canada, this work presents the first estimate of put-on-market electrical and electronic equipment (EEE), the in-use stocks of EEE and e-waste generation in Canada from 1971 to 2030 for 51 product categories comprising 198 product types. Using a dynamic material flow analysis (MFA), the put-on-market EEE is estimated based on trade data retrieved from national and international import and export statistics, and the in-use stocks of EEE and the resulting e-waste are calculated using the Weibull distribution function. The results show that the total mass of EEE within the 60-year period is estimated to be 42.3 million tonnes, with an annual average growth rate of approximately 0.5%. By 2030, the total accumulated in-use stock of EEE is estimated to exceed 13 million tonnes. The estimated e-waste over the 60-year timespan is 29.1 million tonnes. The total annual e-waste generation in Canada is calculated to be 252 kilo tonnes (kt) and 954 kt in the years 2000 and 2020 respectively, which is estimated to reach 1.2 million tonnes by 2030. The e-waste generation per capita increased from 8.3 kg in 2000 to 25.3 kg in 2020 and is estimated to reach 31.5 kg by 2030. This quantification provides valuable insights to policymakers for setting up targets for waste reduction and identifying the resource circularity potential for efficient management of e-waste.

China's electric vehicle and climate ambitions jeopardized by surging critical material prices

The adoption of electric vehicles (EVs) on a large scale is crucial for meeting the desired climate commitments, where affordability plays a vital role. However, the expected surge in prices of lithium, cobalt, nickel, and manganese, four critical materials in EV batteries, could hinder EV uptake. To explore these impacts in the context of China, the world's largest EV market, we expand and enrich an integrated assessment model. We find that under a high material cost surge scenario, EVs would account for 35% (2030) and 51% (2060) of the total number of vehicles in China, significantly lower than 49% (2030) and 67% (2060) share in the base-line, leading to a 28% increase in cumulative carbon emissions (2020-2060) from road transportation. While material recycling and technical battery innovation are effective long-term countermeasures, securing the supply chains of critical materials through international cooperation is highly recommended, given geopolitical and environmental fragilities.

Cell-free synthesis of silver nanoparticles in spent media of different Aspergillus species

The recovery and valorization of metals and rare earth metals from wastewater are of great importance to prevent environmental pollution and recover valuable resources. Certain bacterial and fungal species are capable of removing metal ions from the environment by facilitating their reduction and precipitation. Even though the phenomenon is well documented, little is known about the mechanism. Therefore, we systematically investigated the influence of nitrogen sources, cultivation time, biomass, and protein concentration on silver reduction capacities of cell-free cultivation media (spent media) of Aspergillus niger, A. terreus, and A. oryzae. The spent medium of A. niger showed the highest silver reduction capacities with up to 15 μmol per milliliter spent medium when ammonium was used as the sole N-source. Silver ion reduction in the spent medium was not driven by enzymes and did not correlate with biomass concentration. Nearly full reduction capacity was reached after 2 days of incubation, long before the cessation of growth and onset of the stationary phase. The size of silver nanoparticles formed in the spent medium of A. niger was influenced by the nitrogen source, with silver nanoparticles formed in nitrate or ammonium-containing medium having an average diameter of 32 and 6 nm, respectively.

Emerging enzyme surface display systems for waste resource recovery

The current century marks an inflection point for human progress, as the developed world increasingly comes to recognize that the ecological and socioeconomic impacts of resource extraction must be balanced with more sustainable modes of growth that are less reliant on non-renewable sources of energy and materials. This has opened a window of opportunity for cross-sector development of biotechnologies that harness the metabolic problem-solving power of microbial communities. In this context, recovery has emerged as an organizing principal to create value from industrial and municipal waste streams, and the search is on for new enzymes and platforms that can be used for waste resource recovery at scale. Enzyme surface display on cells or functionalized materials has emerged as a promising platform for waste valorization. Typically, surface display involves the use of substrate binding or catalytic domains of interest translationally fused with extracellular membrane proteins in a microbial chassis. Novel display systems with improved performance features include S-layer display with increased protein density, spore display with increased resistance to harsh conditions, and intracellular inclusions including DNA-free cells or nanoparticles with improved social licence for in situ applications. Combining these display systems with advances in bioprinting, electrospinning and high-throughput functional screening have potential to transform outmoded extractive paradigms into 'trans-metabolic" processes for remediation and waste resource recovery within an emerging circular bioeconomy.

Current Trends in Metal Biomining with a Focus on Genomics Aspects and Attention to Arsenopyrite Leaching-A Review

The presented review is based on scientific microbiological articles and patents in the field of biomining valuable metals. The main attention is paid to publications of the last two decades, which illustrate some shifts in objects of interest and modern trends both in general and applied microbiology. The review demonstrates that microbial bioleaching continues to develop actively, despite various problems in its industrial application. The previous classic trends in the microbial bioleaching persist and remain unchanged, including (i) the search for and selection of new effective species and strains and (ii) technical optimization of the bioleaching process. Moreover, new trends were formed during the last decades with an emphasis on the phylogeny of leaching microbiota and on genomes of the leaching microorganisms. This area of genomics provides new, interesting information and forms a basis for the subsequent construction of new leaching strains. For example, this review mentions some changed strains with increased resistance to toxic compounds. Additionally, the review considers some problems of bioleaching valuable metals from toxic arsenopyrite.

Evolutionary game analysis of WEEE recycling tripartite stakeholders under variable subsidies and processing fees

The standardization of formal recycling and rational subsidy plays an important role in waste electrical and electronic equipment recycling. In order to explore the tripartite decision and evolution path of waste electrical and electronic equipment recycling in different time periods, a tripartite evolutionary game model consisting of recyclers, manufacturers, and government are presented. Moreover, the evolution stability strategies and conditions in each period are calculated by replicating the dynamic equation and Jacobian matrix. Numerical simulations on tripartite evolution stability strategies corresponding to different stages of industry development are used to verify the rationality of the model. The results indicate that there is existed an indirect effect between tripartite decisions, and the indirect effect can expand the slack of tripartite decisions' thresholds of waste electrical and electronic equipment recycling. The variable subsidy in waste electrical and electronic equipment recycling proposed in this paper is useful to incentive recyclers to choose a formal recycling strategy, and manufacturers also choose production with recycled materials as subsidy varies. Besides, the appropriate waste electrical and electronic equipment processing fee is a conducive indirect effect for the tripartite decision to the optimal evolutionary stability strategy in waste electrical and electronic equipment recycling and can promote manufacturers to produce with the recycled materials. The research can assist in benefit coordination and behavior adjustment of waste electrical and electronic equipment recycling members and provide a theoretical basis for the government to formulate appropriate recycling subsidies to promote the formal recycling of electronic waste recycling.

A review on the bioleaching of toxic metal(loid)s from contaminated soil: Insight into the mechanism of action and the role of influencing factors

The anthropogenic activities in agriculture, industrialization, mining, and metallurgy combined with the natural weathering of rocks, have led to severe contamination of soils by toxic metal(loid)s. In an attempt to remediate these polluted sites, a plethora of conventional approaches such as Solidification/Stabilization (S/S), soil washing, electrokinetic remediation, and chemical oxidation/reduction have been used for the immobilization and removal of toxic metal(loid)s in the soil. However, these conventional methods are associated with certain limitations. These limitations include high operational costs, high energy demands, post-waste disposal difficulties, and secondary pollution. Bioleaching has proven to be a promising alternative to these conventional approaches in removing toxic metal(loid)s from contaminated soil as it is cost-effective, environmentally friendly, and esthetically pleasing. The bioleaching process is influenced by factors including pH, temperature, oxygen, and carbon dioxide supply, as well as nutrients in the medium. It is crucial to monitor these parameters before and throughout the reaction since a change in any, for instance, pH during the reaction, can alter the microbial activity and, therefore, the rate of metal leaching. However, research on these influencing factors and recent innovations has brought significant progress in bioleaching over the years. This critical review, therefore, presents the current approaches to bioleaching and the mechanisms involved in removing toxic metal(loid)s from contaminated soil. We further examined and discussed the fundamental principles of various influencing factors that necessitate optimization in the bioleaching process. Additionally, the future perspectives on adding omics for bioleaching as an emerging technology are discussed.

Fungal biotechnology for urban mining of metals from waste printed circuit boards: A review

Rapid surge in electronic waste (e-waste) and its unscientific handling has an adverse impact on humans and the environment. Waste printed circuit board (WPCB), an integrated component of e-waste, has a high metallic content that includes both toxic and precious metals. Therefore, metal recovery is essential not just to avoid environmental degradation but also for economic growth. The current literature analysis focuses on one such eco-friendly approach, known as fungal biotechnology, for extracting metals from WPCBs. Among diverse bioleaching agents, fungi have shown promising metal extraction efficiency (Al: 65-96%; Co: 45-90%; Cu: 34-100%; Ni: 8-95%; Mn: 70-95%; Pb: 27-95%; Zn: 54-99%) and the ability to work in a wide pH range. However, in terms of metal recovery from WPCBs, fungal bioleaching has been less explored. This review, thus, assesses the fungal biotechnology for metal extraction from WPCBs and discusses the associated mechanism and kinetics involved. Different process parameters affecting the fungal bioleaching have also been discussed briefly. The review highlights that, while this process has enough potential, some associated drawbacks hinder its practical applicability on an industrial scale. Lastly, some suggestions for scaling up and reducing the cost of the process have been made, which need to be addressed.

Recovery of critical metals from leach solution of electronic waste using magnetite electrospun carbon nanofibres composite

Scarcity in mining and geo-political direction diverts attention toward critical metal recycling. Gallium (Ga), indium (In) and germanium (Ge) are among the critical metals that consume approximately 80% of world mining in the innovative production of electrical and electronic equipment. The fast obsolescing rate generates a large amount of electronic waste, which is now seen as a secondary reservoir for critical metals. These metal resources need to be dealt with with effective recycling capabilities. Based on solid-phase extraction, magnetic nano-hydrometallurgy is opening a new area of metallic contents recovery in conventional hydrometallurgy. In the present work, polyacrylonitrile (PAN) based electrospun nanofibres were synthesized and carbonized at 800 °C in an inert environment. After surface oxidation, carbon nanofibres were decorated with magnetite particles through co-precipitation. The saturation magnetization value (Ms = 23.6 emu/g) confirms high loading of magnetite particles. The selected critical metal ions are freely present in an aqueous solution at pH 1 to 3; thus, highest removal efficiency was observed at pH 2. Pseudo-second-order kinetics confirm the chemical/charge interaction between sorbent and sorbate ions. Maximum sorption capacity calculated through Langmuir isotherm was 226, 191 and 171 mg/g for Ge(IV), Ga(III) and In(III) metal ions, respectively. The R_L value (0 < R_L < 1) indicates favourable sorption process. The sorbed target metal ions were collectively eluted using 1 mol/L hydrochloric acid. The preconcentration factor was calculated at 1080 for Ge(IV) and In(III) while 1260 for Ga(III). The method was validated with 5 µg/mL spiked multi-element standards and applied to multiple acid-leached electronic waste samples like PCBs, waste LCD panels and solar panels. Recoveries in the range of 96.2% for Ga(III), 95.6% for In(III) and 97.4% for Ge(IV) in the presence of diverse ions indicate the suitability of the proposed method for target metal ions even in a complex matrix.

Genome mining to unravel potential metabolic pathways linked to gallium bioleaching ability of bacterial mine isolates

Gallium (Ga) is considered a high-tech Critical Metal, used in the manufacture of several microelectronic components containing either gallium arsenide (GaAs) or gallium nitride (GaN). The current high demand for this critical metal urges the development of effective recovery processes from secondary resources such as mine tailings or electronic recycling material. The importance of bioleaching as a biotechnological process to recover metals prompted this study, where an integrative approach combining experimental and genomic analysis was undertaken to identify potential mechanisms involved in bioleaching ability and strategies to cope with high metal(loid)s concentrations in five mine isolates. The Clusters of Orthologous Group (COG) annotation showed that the “amino acid transport and metabolism” [E] was the most predominant functional category in all genomes. In addition, the KEEG pathways analysis also showed predicted genes for the biosynthetic pathways of most amino acids, indicating that amino acids could have an important role in the Ga leaching mechanism. The presence of effective resistance mechanisms to Ga and arsenic (As) was particularly important in GaAs bioleaching batch assays, and might explain the divergence in bioleaching efficiency among the bacterial strains. Rhodanobacter sp. B2A1Ga4 and Sphingomonas sp. A2-49 with higher resistance, mainly to As, were the most efficient bioleaching strains under these conditions. In bioleaching assays using cell-free spent medium Arthrobacter silviterrae A2-55 with lower As resistance outperformed all the other stains. Overall, higher efficiency in Ga leaching was obtained in bioleaching assays using GaAs when compared to GaN.

Copper recovery through biohydrometallurgy route: chemical and physical characterization of magnetic (m), non-magnetic (nm) and mix samples from obsolete smartphones

The more modern electronics are, the smaller and complex printed circuit boards are. Thus, these materials are continually changed (physicochemically), increasing the copper concentrations in smartphones. In this sense, it is challenging to set standardized recycling processes to improve metal recovery. In addition, biohydrometallurgy is a clean and cheap process to obtain critical metals from low-grade sources and waste electronic equipment. Therefore, the aim of this work was to characterize, physicochemically, 21 PCBs from smartphones manufactured from 2010 to 2015, and then to recover the copper by Acidithiobacillus ferrooxidans (biohydrometallurgy). The PCBs were comminuted and separated into Magnetic (M), Nonmagnetic (NM) and without magnetic separation (MIX) samples. It was identified 217.8; 560.3 and 401.3 mg Cu/g of PCBs for M, NM and MIX samples, respectively. Regarding biohydrometallurgy, the culture media iron-supplemented (NM + Fe and MIX + Fe) increased the copper content by 2.6 and 7.2%, respectively, and the magnetic separation step was insignificant.

Selective removal and recovery of gallium and germanium from synthetic zinc refinery residues using biosorption and bioprecipitation

The depletion of primary ores, the environmental concerns related to mining activities, and the need to promote circular economy has drawn attention to the recycling of metallic compounds. Bio-based technologies are suitable for metal recovery, as they operate under mild conditions (ambient temperature and pressure) and are ideal for treating low-concentration waters. This study compared the effectiveness of adsorption and precipitation for the removal and recovery of gallium, germanium and zinc. Adsorption of the metallic ions on elemental forms of sulfur (S⁰), selenium (Se⁰) and tellurium (Te⁰), both of chemical and biological sources, was tested. Biosorption onto elemental forms of S⁰_bio, Se⁰_bio and Te⁰_bio effectively removed Ga and Zn. The highest removal efficiency (ղ) was obtained for Ga onto the adsorbent Te⁰_bio (69 ± 0.4%), with an adsorption capacity (q) of 74 mg Ga (g Te⁰_bio)^-1, followed by Zn (ղ = 40 ± 0.7%) with 43 mg Zn (g Te⁰_bio)^-1. Precipitation with chemical and biogenic sulfide at different metal to sulfide (Me/S) ratios was also assessed. Biologically produced sulfide was more efficient for Ga and Zn compared to chemical sulfide. Precipitation with biogenic sulfide was efficient for the removal of Ga (ղ = 59.9 ± 2.6%) and Zn (ղ = 44.2 ± 3.0%). The lowest ratio between metal to sulfide (Me/S = 0.2) achieved higher zinc removal efficiencies, whereas gallium removal was more efficient at Me/S = 1.5. None of the tested methods allowed for recovery of Ge. Biosorption and bioprecipitation gave nevertheless high removal and recovery of Ga and Zn.

Selective recovery of gold from dilute aqua regia leachate of waste printed circuit board by thiol-modified garlic peel

Garlic peel (GP) was chemically modified by using thiourea under hydrothermal treatment, which could selectively adsorb gold ions from the 1/10 dilute aqua regia media directly without needing the dangerous evaporation operation. The synthetic chloroauric solution and practical leach liquor of the waste PCB (printed circuit board) powder in dilute aqua regia were employed to assess the adsorption performance on the thiol-GP and the commercial quaternary ammonia anion resin of D201, respectively. It was experimentally confirmed that the adsorption efficiency of gold onto the thiol-GP and D201 resin both reached 100%, and the maximum adsorption capacity of thiol-GP gel was evaluated as 42.59 mg Au/g that was much larger than that of D201 resin (3.33 mg Au/g). The thiol-GP gel adsorption efficiency of other coexisting base metal ions like Cu²⁺, Ni²⁺, Al³⁺, and Fe³⁺ from dilute aqua regia leach liquor of the waste PCB powder was near zero, and only gold could be enriched by selective adsorption onto the thiol-GP gel. At least 3 cycles of adsorption/elution could be obtained without decreasing the adsorption efficiency drastically. The adsorbed gold on the thiol-GP was able to be eluted effectively by using the mixture solution of 0.1 M thiourea and 0.1 M hydrochloric acid, and finally the solid gold could be recovered by sodium borohydride through a reduction process. This study demonstrated a green, environmentally friendly, low-cost, and efficient method for selective recovery of gold from the dilute leach liquor (aqua regia) of waste circuit boards.

Photocatalytic Materials Obtained from E-Waste Recycling: Review, Techniques, Critique, and Update

Waste-derived materials obtained from the recovery and recycling of electronic waste (e-waste) such as batteries and printed circuit boards have attracted enormous attention from academia and industry in recent years, especially due to their eco-friendly nature and the massive increment in e-waste due to technological development. Several investigations in the literature have covered the advances achieved so far. Meanwhile, photocatalytic applications are especially of interest since they maintain mutual benefits and can be used for H2 production from solar water splitting based on semiconductor processing as a proper environmentally friendly technique for solar energy conversion. In addition, they can be utilized to degrade a variety of organic and non-organic contaminations. Nonetheless, to the best of the authors’ knowledge, there has not been any comprehensive review that has specifically been focused on e-waste-derived photocatalytic materials. In this regard, the present work is dedicated to thoroughly discussing the related mechanisms, strategies, and methods, as well as the various possible photocatalysts synthesized from e-wastes with some critiques in this field. This brief overview can introduce modern technologies and promising possibilities for e-waste valorization, photocatalytic processes, and new photocatalytic degradation methods of eco-friendly nature. This paper discusses various e-waste-obtained photocatalytic materials, synthesis procedures, and applications, as well as several types of e-waste, derived materials such as TiO2, ZnO, indium tin oxide, and a variety of sulfide- and ferrite-based photocatalytic materials.

Bioleaching of Typical Electronic Waste-Printed Circuit Boards (WPCBs): A Short Review

The rapid pace of innovations and the frequency of replacement of electrical and electronic equipment has made waste printed circuit boards (WPCB) one of the fastest growing waste streams. The frequency of replacement of equipment can be caused by a limited time of proper functioning and increasing malfunctions. Resource utilization of WPCBs have become some of the most profitable companies in the recycling industry. To facilitate WPCB recycling, several advanced technologies such as pyrometallurgy, hydrometallurgy and biometallurgy have been developed. Bioleaching uses naturally occurring microorganisms and their metabolic products to recover valuable metals, which is a promising technology due to its cost-effectiveness, environmental friendliness, and sustainability. However, there is sparse comprehensive research on WPCB bioleaching. Therefore, in this work, a short review was conducted from the perspective of potential microorganisms, bioleaching mechanisms and parameter optimization. Perspectives on future research directions are also discussed.

A holistic approach for the recovery of rare earth elements and scandium from secondary sources under a circular economy framework - A review

Limited natural resources and a continuous increase in the demand for modern technological products, is creating a demand and supply gap for rare earth elements (REEs) and Sc. There is therefore a need to adopt the sustainable approach of the circular economy system (CE). In this review, we defined six steps required to close the loop and recover REEs, using a holistic approach. Recent statistics on REEs and Sc demand and the number of waste generations are reported and studies on more environmentally friendly, economic, and/or efficient recovery processes are summarized. Pilot-scale recovery facilities are described for several types of secondary sources. Finally, we identify obstacles to closing the REE loop in a circular economy and the reasons why secondary sources are not preferred over primary sources. Briefly, recovery from secondary sources should be environmentally and economically friendly and of an acceptable standard concerning final product quality. However, current technologies for recovery from for secondary sources are limiting and technology needs will vary depending on the source type. The quality/purity of the recovered metals should be proven so that they do not result in any adverse effects on the product quality, when they are being used as secondary raw material. In addition, for industrial-scale facilities, process improvements are required that consider environmental conditions.

Scandium-microorganism interactions in new biotechnologies

Scandium (Sc) plays a special role in high-tech industries because of its wide application in green, space, and defense technologies. However, Sc mining and purification are problematic due to political, technological, and environmental difficulties. The deficit of this element limits global technological development. One sustainable solution to this problem is to use microorganisms to extract Sc from ore and waste, as well as to concentrate and separate it from other elements. Sc also demonstrates attractive metabolic effects on microbes that is of great interest in white biotechnology. Sc increases the production of proteins and secondary metabolites and activates poorly expressed genes. This review offers a comprehensive analysis of current knowledge on the application of Sc-microorganism interactions in promising biotechnologies, its perspectives, and future challenges.

Seaweed’s Role in Energetic Transition—From Environmental Pollution Challenges to Enhanced Electrochemical Devices

Simple Summary

Earth is currently facing the effects of climate change in all environmental ecosystems; this, together with pollution, is the cause of species extinction and biodiversity loss. Thus, it is vital to take actions to mitigate and decrease the release of greenhouse gases to the atmosphere. The emergence of energetic transition from fossil fuels to greener energies is clearly defined in the United Nations 2030 agenda. Although this transition endorses the ambitious goal to supply greener energy for all developed societies, the increased demand for the minerals essential to develop cleaner energetic technologies has highlighted several economic and environmental issues. Currently, these minerals are mainly obtained by mining activities that generate high levels of soil and water pollution, coupled with the intensive use of water and hazardous gas release. On the other hand, the exponential increase of electronic waste derived from end-of-life electronic equipment is already raising environmental concerns due to heavy metal contamination as a result of their disposal. Thus, it is vital to develop sustainable and efficient strategies to mitigate energetic transition environmental footprints. This review highlights the use of seaweed biomass for toxic mineral bioremediation, recycling, and as an alternative material for greener energy-storage device development.

Abstract

Resulting from the growing human population and the long dependency on fossil-based energies, the planet is facing a critical rise in global temperature, which is affecting all ecosystem networks. With a growing consciousness this issue, the EU has defined several strategies towards environment sustainability, where biodiversity restoration and preservation, pollution reduction, circular economy, and energetic transition are paramount issues. To achieve the ambitious goal of becoming climate-neutral by 2050, it is vital to mitigate the environmental footprint of the energetic transition, namely heavy metal pollution resulting from mining and processing of raw materials and from electronic waste disposal. Additionally, it is vital to find alternative materials to enhance the efficiency of energy storage devices. This review addresses the environmental challenges associated with energetic transition, with particular emphasis on the emergence of new alternative materials for the development of cleaner energy technologies and on the environmental impacts of mitigation strategies. We compile the most recent advances on natural sources, particularly seaweed, with regard to their use in metal recycling, bioremediation, and as valuable biomass to produce biochar for electrochemical applications.

Microbial biominers: Sequential bioleaching and biouptake of metals from electronic scraps

Electronic scraps (e-scraps) represent an attractive raw material to mine demanded metals, as well as rare earth elements (REEs). A sequential microbial-mediated process developed in two steps was examined to recover multiple elements. First, we made use of an acidophilic bacteria consortium, mainly composed of Acidiphilium multivorum and Leptospidillum ferriphilum, isolated from acid mine drainages. The consortium was inoculated in a dissolution of e-scraps powder and cultured for 15 days. Forty-five elements were analyzed in the liquid phase over time, including silver, gold, and 15 REEs. The bioleaching efficiencies of the consortium were >99% for Cu, Co, Al, and Zn, 53% for Cd, and around 10% for Cr and Li on Day 7. The second step consisted of a microalgae-mediated uptake from e-scraps leachate. The strains used were two acidophilic extremotolerant microalgae, Euglena sp. (EugVP) and Chlamydomonas sp. (ChlSG) strains, isolated from the same extreme environment. Up to 7.3, 4.1, 1.3, and 0.7 µg by wet biomass (WB) of Zn, Al, Cu, and Mn, respectively, were uptaken by ChlSG biomass in 12 days, presenting higher efficiency than EugVP. Concerning REEs, ChlSG biouptake 14.9, 20.3, 13.7, 8.3 ng of Gd, Pr, Ce, La per WB. Meanwhile, EugVP captured 1.1, 1.5, 1.4, and 7.5, respectively. This paper shows the potential of a microbial sequential process to revalorize e-scraps and recover metals and REEs, harnessing extremotolerant microorganisms.

Bioleaching of Heavy Metals from Printed Circuit Boards with an Acidophilic Iron-Oxidizing Microbial Consortium in Stirred Tank Reactors

In this study, bioleaching was carried out for the recovery of metals (copper, zinc, tin, lead, gold and silver) from printed circuit boards residues (PCBs), one of the most important wastes from electrical and electronic equipment, using an acidophilic iron-oxidizing bacterial consortium enriched with minerals from a gold mine in the Arequipa region, Peru. High-throughput sequencing and analysis of the 16S rRNA biomarker revealed that this consortium was predominantly composed of Tissierella, Acidiphilium and Leptospirillum bacteria, from which the latter is known to grow by chemolithotrophy through iron oxidation. After the enrichment process, the acidophilic iron-oxidizing consortium was first tested for its tolerance to different PCBs concentrations, showing best growth up to 10 g/L of PCBs and a tolerance index of 0.383. Based on these results, the bioleaching efficiency of the consortium was investigated for 10 g/L of PCBs in stirred tank reactors coupled to an aeration system, for 18 days. High bioleaching efficiencies were achieved for copper and zinc (69% and 91%, respectively), indicating that these two metals can be easily extracted in this leaching system. Lower extraction efficiencies were achieved for tin (16%) and gold (28%), while for lead and silver only a residual recovery (<0.25%) was detected. These results indicate that the enriched bacterial consortium originating from the Arequipa region, Peru, has a high capacity to recover different metals of economic importance.

Process development options for electronic waste fractionation to achieve maximum material value recovery

Revised legislation and bans on imports of waste electrical and electronic equipment (WEEE) into many Asian countries for treatment are driving the need for more efficient WEEE fractionation in Europe by expanding the capacity of treatment plants and improving the percentage recovery of materials of economic value. Data from a key stakeholder survey and consultation are combined with the results of a detailed literature survey to provide weighted matrix input into multi-criteria decision analysis calculations to carry out the following tasks: (a) assess the relative importance of 12 process options against the 6 industry-derived in-process economic potential criteria, that is, increase in product quality, increase in recycling rate, increase in process capacity, decrease in labour costs, decrease in energy costs and decrease in disposal costs; and (b) rank 25 key technologies that have been selected as being the most likely to benefit the efficient sorting of WEEE. The results indicate that the first stage in the development of any total system to achieve maximum economic recovery of materials from WEEE has to be the selection and application of appropriate fractionation process technologies to concentrate valuable components such as critical metals into the smallest possible fractions to achieve their recovery while minimising the disposal costs of low-value products. The stakeholder-based study has determined the priority for viable technical process developments for efficient WEEE fractionation and highlighted the economic and technical improvements that have to be made in the treatment of WEEE.

A review on recent advancements in recovery of valuable and toxic metals from e-waste using bioleaching approach

This review is intent on the environmental pollution generated from printed circuit boards and the methods employed to retrieve valuable and hazardous metals present in the e-wastes. Printed circuit boards are the key components in the electronic devices and considered as huge e-pollutants in polluting our surroundings and the environment as a whole. Composing of toxic heavy metals, it causes serious health effects to the plants, animals and humans in the environment. A number of chemical, biological and physical approaches were carried out to recover the precious metals and to remove the hazardous metals from the environment. Chemical leaching is one of the conventional PCBs recycling methods which was carried out by using different organic solvents and chemicals. Need of high cost for execution, generation of secondary wastes in the conventional methods, forces to discover the advanced recycling methods such as hydrometallurgical, bio-metallurgical and bioleaching processes to retrieve the valuable metals generate through e-wastes. Among them, bioleaching process gain extra priority due to its higher efficiency of metal recovery from printed circuit boards. There are different classes of microorganisms have been utilized for precious metal recovery from the PCBs through bioleaching process such as chemolithoautotrophy, heterotrophy and different fungal species including Aspergillus sp. and Penicillium sp. The current status and scope for further studies in printed circuit boards recycling are discussed in this review.

Microbial recovery of critical metals from secondary sources

The continuous development of technologies involving critical metals, both in Europe and over the world, and geopolitical challenges in areas rich in critical metal sources, imposed increased research efforts to recover them from secondary sources, by eco-efficient processes. Yet, microbes-metal interactions are not sufficiently exploited to recover metals from secondary sources, although they are already used in ore extraction. This review examines and compare strategies and processes involving microorganisms for critical metals recovery, since conventional physico-chemical methods are energy-intensive and often polluting. Two groups of microbial assisted recovery processes are discussed: metal mobilization from metal bearing waste, and selective metal separation from leaching solutions by immobilization on microbial biomass. Because most of the identified microbial technologies are developed on laboratory scale, the increase of biorecovery efficiency is compulsory for enhancing scaling-up potential. Future developments focused on novel microorganisms and high-performance strategies for critical metal recovery by microbial processes are considered.

Analytical and reclamation technologies for identification and recycling of precious materials from waste computer and mobile phones

Waste electrical and electronic equipment (WEEE) is one of the world's fastest-growing class of waste. WEEE contain a large amount of precious materials that have aroused the interest to develop new recycling technologies. Hence, effective recycling strategies are extremely necessary to promote the proper handling of these materials as well as for environmentally sound recovery of secondary raw resource. This paper reviews important existing methods and emerging technologies in WEEE management, with special emphasis in characterization, extraction and reclamation of precious materials from waste computer and mobile phones. Traditional pyrometallurgical and hydrometallurgical technologies still play a central role in the recovery of metals. More recently, emerging greener recycling technologies using microorganisms (i.e. biometallurgical), plasma arc fusion method and pretreatments (i.e. ultrasound and mechanochemical technologies) combined with other recycling methods (e.g. hydrometallurgical), and using less toxic solvents such as ionic liquids (ILs) and deep eutectic solvents (DESs) have also been attempted to recycle metals from computer and mobile phone scrap. The role of analytical method development, especially using spectroanalytical methods for chemical inspection and e-waste sorting process at industrial applications is also discussed. This confirmed that most direct sampling techniques such as laser-induced breakdown spectroscopy (LIBS) and X-ray fluorescence (XFR) have several advantages over traditional sorting methods including rapid analytical response, without use of chemical reagents or waste generation, and greater reclamation of precious and critical materials in the WEEE stream.

A DedA Family Membrane Protein in Indium Extrusion in Rhodanobacter sp. B2A1Ga4

Indium (In) is a critical metal widely used in electronic equipment, and the supply of this precious metal is a major challenge for sustainable development. The use of microorganisms for the recovery of this critical high-tech element has been considered an excellent eco-friendly strategy. The Rhodanobacter sp. B2A1Ga4 strain, highly resistant to In, was studied in order to disclose the bacterial mechanisms closely linked to the ability to cope with this metal. The mutation of the gene encoding for a DedA protein homolog, YqaA, affected drastically the In resistance and the cellular metabolic activity of strain Rhodanobacter sp. B2A1Ga4 in presence of this metal. This indicates that this protein plays an important role in its In resistance phenotype. The negative impact of In might be related to the high accumulation of the metal into the mutant cells showing In concentration up to approximately 4-fold higher than the native strain. In addition, the expression of the yqaA gene in this mutant reverted the bacterial phenotype with a significant decrease of In accumulation levels into the cells and an increase of In resistance. Membrane potential measurements showed similar values for native and mutant cells, suggesting that there was no loss of proton-motive force in the mutant cells. The results from this study suggest a potential role of this DedA family protein as a membrane transporter involved in the In efflux process. The mutant strain also has the potential to be used as a biotool in bioaccumulation strategies, for the recovery of In in biomining activities.

Cobalt Recovery from Li-Ion Battery Recycling: A Critical Review

The increasing demand for Li-ion batteries for electric vehicles sheds light upon the Co supply chain. The metal is crucial to the cathode of these batteries, and the leading global producer is the D.R. Congo (70%). For this reason, it is considered critical/strategic due to the risk of interruption of supply in the short and medium term. Due to the increasing consumption for the transportation market, the batteries might be considered a secondary source of Co. The outstanding amount of spent batteries makes them to a core of urban mining warranting special attention. Greener technologies for Co recovery are necessary to achieve sustainable development. As a result of these sourcing challenges, this study is devoted to reviewing the techniques for Co recovery, such as acid leaching (inorganic and organic), separation (solvent extraction, ion exchange resins, and precipitation), and emerging technologies—ionic liquids, deep eutectic solvent, supercritical fluids, nanotechnology, and biohydrometallurgy. A dearth of research in emerging technologies for Co recovery from Li-ion batteries is discussed throughout the manuscript within a broader overview. The study is strictly connected to the Sustainability Development Goals (SDG) number 7, 8, 9, and 12.

Enhancement of WEEE Management Practices in MTN Phone Village, Rumukurushi, Port Harcourt, Nigeria

Informal recycling has been a source of challenges to a mobile telephone network (MTN) phone village in Rumukurushi, Port Harcourt, Nigeria, and several locations in developing countries. In order to bring a lasting solution to the menace of informal recycling in this location, the study proposed a new waste electrical and electronic equipment (WEEE) management system. The system comprises the application of two key concepts. The first concept includes limiting the activities of informal recyclers to WEEE collection only. This implies WEEE treatment, dismantling, etc., are carried out by government-approved agencies and experts. The second concept involves the application of the just-in-time (JIT) management concept for managing WEEE. The concept ensures that WEEE is only requested from the recycler or the individuals in possession of it and only on demand. The study adopted a qualitative research approach. Data collection and analysis were achieved via semi-structured phone interviews and thematic analysis, respectively. The outcome of the study limits the activities of the informal recyclers to WEEE collection. Informal recyclers gain revenue from collection. A reduction in the waiting time of workers and WEEE storage space is achieved. This offers safety, efficiency, and an increased productivity. This will help to revolutionise the WEEE management system in the location.

A post-pandemic sustainable scenario: What actions can be pursued to increase the raw materials availability?

On January 30, 2020, COVID-19 outbreak, detected for the first time in Wuhan (China), was declared by WHO a Public Health Emergency. In a strongly connected world, the consequent slowdown of the Chinese economy contributed to disrupt the global supply chains of several products. In a post-pandemic scenario, the expected rapid increase in demand of critical raw materials (associated with the transition to more green energy sources), coupled with the problems that some mining activities are relegated only in certain countries and regions, must be considered in a sustainable perspective. This work analyses the literature about (critical) raw materials and COVID-19, not only to present the impact of the pandemic on their supply, but also to propose some actions that should be pursued in a post-pandemic renaissance scenario, to increase raw materials availability, with great attention to most critical ones, in the frame of circular economy principles. The post-pandemic possibilities are evaluated and suitable actions are suggested to secure the raw materials availability for the foreseen increase of investments in crucial and strategic sectors, in accord with the UN Sustainable Development Goals (SDGs). The proposed actions can be summarized as policy, strategy, economy, and technology activities.

Study on the Behavior of Electrochemical Extraction of Cobalt from Spent Lithium Cobalt Oxide Cathode Materials

The molten salt electrochemical method was used to reduce the Co in spent LiCoO₂. The reduction mechanism of Co (III) in LiCoO₂ was analyzed by cyclic voltammetry, square wave voltammetry, and open circuit potential. The reduction process of Co (III) on Fe electrode was studied in NaCl-CaCl₂-LiCoO₂ molten salt system at 750 °C. The results show that the reduction process of Co (III) is a two-step reduction: Co (III) → Co (II) → Co (0) and they are all quasi-reversible processes controlled by diffusion. Phase analysis (XRD) shows that Li⁺ and Cl^2- in the molten salt form LiCl electrolysis experiments with different voltages were carried out, which proved the stepwise reduction of Co in LiCoO₂.

Bioleaching of indium from waste LCD panels by Aspergillus niger: Method optimization and mechanism analysis

Using Aspergillus niger (A. niger) to produce low-concentration organic acids is challenging for dissolving In₃O₂ from waste LCD (liquid crystal display) panels with high toxicity. In this study, three bioleaching approaches from the general and the optimized fermentation systems were investigated respectively to compare indium recovery effects and firstly clarified its bioleaching mechanism. The indium bioleaching efficiency can be improved from 12.3% to 100% by fermentation method optimization. Carboxy groups from organic acids and proteins were the critical substances to release H⁺ for leaching indium mainly competed with iron via reactions analysis. The effective components increased after optimizing, including the dissociative H⁺ concentration, the effective carboxyl groups for leaching metal oxides, and the output of oxalic acid. A. niger biomass prevented the contact between H⁺ and In₃O₂ and adsorbed In³⁺ adverse to indium recovery. The bioleaching effects of fermentation broth for indium can be further promoted by controlling bioleaching process parameters.

Evidence of Resistance of Heavy Metals from Bacteria Isolated from Natural Waters of a Mining Area in Mexico

This study focuses on identifying relationships between the content of heavy metals in water and the resistance patterns of different bacteria. Samples from watercourses in one of the most important mining areas in Mexico were collected. Seventy-one bacteria were isolated, and their resistance to Cr, Zn, Cu, Ag, Hg, and Co was studied. The Minimum Inhibitory Concentration range was determined, and a Multiple Metal Resistant index was calculated. After that, 11 isolated bacteria were chosen to estimate kinetic parameters. The obtained results show differences in the behavior of the studied bacteria concerning the presence of heavy metals in the media: (1) without effect, (2) inhibited growth; and (3) considerable inhibited growth. Finally, a Performance Index was proposed to select adequate bacteria for heavy metals removal; five bacteria were selected. Among them, Pseudomonas koreensis was identified as a good candidate for a future biosorption system since these bacteria can stimulate growth in the presence of all the metals tested.

Electric car battery: An overview on global demand, recycling and future approaches towards sustainability

Li-ion batteries are daily present in our electronic devices. These batteries are used in electric and hybrid vehicles supporting the current agreements to decrease greenhouse gas emissions. As a result, the electric vehicle demand has increased in the world. As Li-ion batteries are composed of critical metals in which there is a risk of interruption of supply in the medium term, recycling is the key to a sustainable future without internal combustion vehicles. Understanding the current scenario and future perspectives is important for strategies of new battery design, recycling routes and reverse logistics, as well as policies for sustainable development. This paper presents an overview of current and future vehicles used worldwide. An increase from 1.3 to 2 billion vehicles is expected worldwide until 2030; an outstanding demand will occur mainly in BRICS countries. The data demonstrated a correlation between the number of vehicles in use and GDP. Patents and processes designed for recycling Li-ion batteries and the new developments on pyro-, hydro-, and bio-metallurgical routes have been revised. The manuscript describes the importance and benefits of recycling as regards the supply of critical metals and future trends towards a circular economy.

Optimization of zinc bioleaching from paint sludge using Acidithiobacillus thiooxidans based on response surface methodology

The reduction of zinc metal in the paint sludge, a hazardous waste, was investigated using Acidithiobacillus thiooxidans by a two-stage bioleaching process. This process was performed using the response surface methodology (RSM) method based on the central composite design (CCD). Four variables, a temperature range of 32-34.5-37 °C, rotation speed of shaker 120-150-180 rpm, pH of 4.2-3.2-2.2, and particle sizes of 1-2-3 mm, were used to optimize the experiments. The results showed that with a constant pulp density of 10 g/L at 32 °C, shaker speed of 120 rpm, a particle size of 1 mm and pH of 4.2, the highest removal predicted by the software (Design Expert version 11) was 22.89%. Repeating the experiments confirmed a decrease in zinc to the nearest predicted point. According to the ANOVA result, the rotation speed of the shaker has the greatest effect on the bioleaching process, followed by the two variables of the rotation speed of shaker and pH together affects. After the bioleaching process, energy dispersive X-ray (EDX) and mapping analysis showed quantitative changes in the chemical composition of the paint sludge, and morphological changes of texture were confirmed by scanning electron microscopy (SEM).

Bioleaching of E-Waste: Influence of Printed Circuit Boards on the Activity of Acidophilic Iron-Oxidizing Bacteria

Bioleaching is a promising strategy to recover valuable metals from spent printed circuit boards (PCBs). The performance of the process is catalyzed by microorganisms, which the toxic effect of PCBs can inhibit. This study aimed to investigate the capacity of an acidophilic iron-oxidizing culture, mainly composed of Leptospirillum ferriphilum, to oxidize iron in PCB-enriched environments. The culture pre-adapted to 1% (w/v) PCB content successfully thrived in leachates with the equivalent of 6% of PCBs, containing 8.5 g L^–1 Cu, 8 g L^–1 Fe, 1 g L^–1 Zn, 92 mg L^–1 Ni, 12.6 mg L^–1 Pb, and 4.4 mg L^–1 Co, among other metals. However, the inhibiting effect of PCBs limited the microbial activity by delaying the onset of the exponential iron oxidation. Successive subcultures boosted the activity of the culture by reducing this delay by up to 2.6 times under batch conditions. Subcultures also favored the rapid establishment of high microbial activity in continuous mode.