Removal of pharmaceutical and personal care products (PPCPs) from wastewater using microalgae: A review

Exploring the influence of sulfadiazine-induced stress on antibiotic removal and transformation pathway using microalgae Chlorella sp

Sulfadiazine (SDZ) is a kind of anti-degradable antibiotics that is commonly found in wastewater, but its removal mechanism and transformation pathway remain unclear in microalgal systems. This study investigated the effects of initial algae concentration and SDZ-induced stress on microalgal growth metabolism, SDZ removal efficiency, and transformation pathways during Chlorella sp. cultivation. Results showed that SDZ had an inhibitory effect on the growth of microalgae, and increasing the initial algal biomass could alleviate the inhibitory effect of SDZ. When the initial algal biomass of Chlorella sp. was increased to 0.25 g L-1, the SDZ removal rate could reach 53.27%-89.07%. The higher the initial algal biomass, the higher the SOD activity of microalgae, and the better the protective effect on microalgae, which was one of the reasons for the increase in SDZ removal efficiency. Meanwhile, SDZ stress causes changes in photosynthetic pigments, lipids, total sugars and protein content of Chlorella sp. in response to environmental changes. The main degradation mechanisms of SDZ by Chlorella sp. were biodegradation (37.82%) and photodegradation (23%). Most of the degradation products of SDZ were less toxic than the parent compound, and the green algae were highly susceptible to SDZ and its degradation products. The findings from this study offered valuable insights into the tradeoffs between accumulating microalgal biomass and antibiotic toxic risks during wastewater treatment, providing essential direction for the advancement in future research and full-scale application.

Seawater Chlorella sp. biofilm for mariculture effluent polishing under environmental combined antibiotics exposure and ecological risk evaluation based on parent antibiotics and transformation products

Mariculture effluent polishing with microalgal biofilm could realize effective nutrients removal and resolve the microalgae-water separation issue via biofilm scraping or in-situ aquatic animal grazing. Ubiquitous existence of antibiotics in mariculture effluents may affect the remediation performances and arouse ecological risks. The influence of combined antibiotics exposure at environment-relevant concentrations towards attached microalgae suitable for mariculture effluent polishing is currently lack of research. Results from suspended cultures could offer limited guidance since biofilms are richer in extracellular polymeric substances that may protect the cells from antibiotics and alter their transformation pathways. This study, therefore, explored the effects of combined antibiotics exposure at environmental concentrations towards seawater Chlorella sp. biofilm in terms of microalgal growth characteristics, nutrients removal, anti-oxidative responses, and antibiotics removal and transformations. Sulfamethoxazole (SMX), tetracycline (TL), and clarithromycin (CLA) in single, binary, and triple combinations were investigated. SMX + TL displayed toxicity synergism while TL + CLA revealed toxicity antagonism. Phosphorus removal was comparable under all conditions, while nitrogen removal was significantly higher under SMX and TL + CLA exposure. Anti-oxidative responses suggested microalgal acclimation towards SMX, while toxicity antagonism between TL and CLA generated least cellular oxidative damage. Parent antibiotics removal was in the order of TL (74.5-85.2 %) > CLA (60.8-69.5 %) > SMX (13.5-44.1 %), with higher removal efficiencies observed under combined than single antibiotic exposure. Considering the impact of residual parent antibiotics, CLA involved cultures were identified of high ecological risks, while medium risks were indicated in other cultures. Transformation products (TPs) of SMX and CLA displayed negligible aquatic toxicity, the parent antibiotics themselves deserve advanced removal. Four out of eight TPs of TL could generate chronic toxicity, and the elimination of these TPs should be prioritized for TL involved cultures. This study expands the knowledge of combined antibiotics exposure upon microalgal biofilm based mariculture effluent polishing.

Toxicity of water-soluble polymers polyethylene glycol and polyvinyl alcohol for fish and frog embryos

Personal Care Products (PCPs) have been one of the most studied chemicals in the last twenty years since they were identified as pseudo-persistent pollutants by the European Union in the early 2000s. The accumulation of PCPs in the aquatic environment and their effects on non-target species make it necessary to find new, less harmful, substances. Polyethylene glycol (PEGs) and polyvinyl alcohol (PVAs) are two polymers that have increased their presence in the composition of PCPs in recent years, but little is known about the effect of their accumulation in the environment on non-target species. Through embryotoxicity tests on two common models of aquatic organisms (Danio rerio and Xenopus laevis), this work aims to increase the knowledge of PEGs and PVAs' effects on non-target species. Animals were exposed to the pollutant for 96 h. The main embryotoxicity endpoint (mortality, hatching, malformations, heartbeat rate) was recorded every 24 h. The most significant results were hatching delay in Danio rerio exposed to both chemicals, in malformations (oedema, body malformations, changes in pigmentation and deformations of spine and tail) in D. rerio and X. laevis and significant change in the heartbeat rate (decrease or increase in the rate) in both animals for all chemicals tested.

Bioremediation potential of microalgae for sustainable soil treatment in India: A comprehensive review on heavy metal and pesticide contaminant removal

The escalating environmental concerns arising from soils contamination with heavy metals (HMs) and pesticides (PSTs) necessitate the development of sustainable and effective remediation strategies. These contaminants, known for their carcinogenic properties and toxicity even at small amounts, pose significant threats to both environmental ecology and human health. While various chemical and physical treatments are employed globally, their acceptance is often hindered by prolonged remediation times, high costs, and inefficacy in areas with exceptionally high pollutant concentrations. A promising emerging trend in addressing this issue is the utilization of microalgae for bioremediation. Bioremediation, particularly through microalgae, presents numerous benefits such as high efficiency, low cost, easy accessibility and an eco-friendly nature. This approach has gained widespread use in remediating HM and PST pollution, especially in large areas. This comprehensive review systematically explores the bioremediation potential of microalgae, shedding light on their application in mitigating soil pollutants. The paper summarizes the mechanisms by which microalgae remediate HMs and PSTs and considers various factors influencing the process, such as pH, temperature, pollutant concentration, co-existing pollutants, time of exposure, nutrient availability, and light intensity. Additionally, the review delves into the response and tolerance of various microalgae strains to these contaminants, along with their bioaccumulation capabilities. Challenges and future prospects in the microalgal bioremediation of pollutants are also discussed. Overall, the aim is to offer valuable insights to facilitate the future development of commercially viable and efficient microalgae-based solutions for pollutant bioremediation.

Cd2+ enhancing the bromination of bisphenol A in Brassica chinensis L.: Pathways and mechanisms

Traditional heavy metal pollution, such as cadmium, impacts the transformation and risks of bisphenol pollutants (like bisphenol A, BPA), in plants, especially due to the ubiquitous presence of bromide ion. Although it has been discovered that the bromination of phenolic pollutants occurs in plants, thereby increasing the associated risks, the influence and mechanisms of bromination under complex contamination conditions involving both heavy metals and phenolic compounds remain poorly understood. This study addresses the issue by exposing Brassica chinensis L. to cadmium ion (Cd2+, 25-100 μM), with the hydroponic solution containing BPA (15 mg/L) and bromide ion (0.5 mM) in this work. It was observed that Cd2+ primarily enhanced the bromination of BPA by elevating the levels of reactive oxygen species (ROS) and the activity of peroxidase (POD) in Brassica chinensis L. The variety of bromination products within Brassica chinensis L. increased as the concentration of Cd2+ rose from 25 to 100 μM. The substitution positions of bromine were determined using Gaussian calculations and mass spectrometry analysis. The toxicity of bromination products derived from BPA was observed to increase based on Ecological Structure-Activity Relationships analysis and HepG2 cytotoxicity assays. This study provides new insights into the risks and health hazards associated with cadmium pollution, particularly its role in enhancing the bromination of bisphenol pollutants in plants.

Enhanced tetracycline degradation by novel Mn-FeOOH/CNNS photocatalysts in a visible-light-driven photocatalysis coupled peroxydisulfate system

Recently, photocatalysis combined peroxydisulfate activation under visible light (PC-PDS/Vis) was developed as a promising technology for removing antibiotics in water. Herein, Mn doped FeOOH (Mn-FeOOH) nanoclusters were grown in-situ on the surface of graphitic carbon nitride nanosheets (CNNS) using a wet chemical method, which served as a visible-light-driven photocatalyst for peroxydisulfate (PDS) activation. Photovoltaic property characterizations revealed that Mn-FeOOH/CNNS owned superior light capture ability and carrier separation efficiency. According to DFT calculations, the synergistic effect between Mn and Fe species was proved to enhance the adsorption and activation of PDS. 99.7% of tetracycline (TC) was rapidly removed in 50 minutes in the PC-PDS/Vis system. In addition, Mn-FeOOH/CNNS exhibited high recycling stability with low iron leaching, attributed to the interaction between Mn-FeOOH clusters and carbon species. Quenching experiments and electron spin resonance (ESR) tests unveiled that •O2- played a significant role in TC removal, while •OH and SO4•- acted as additional roles contributing to the overall process. These findings given a new strategy for antibiotics degradation by photocatalysis, offering deeper insights for the advancement of sustainable and cutting-edge wastewater treatment technologies.

Peroxymonosulfate activation by superparamagnetic mixed-valent Cu/N-(L-cysteine)-O-(carboxymethyl)chitosan/cobalt ferrate-rice hull hybrid nanocomposite for efficient degradation of naproxen: Synergetic adsorption-catalysis, kinetics, pathway, and relevant mechanism

Naproxen (NPX) as an emerging anthropogenic contaminant was detected in many water sources, which can pose a serious threat to the environment and human health. Peroxymonosulfate (PMS) decomposed by Cu(I) has been considered an effective activation method to produce reactive species. However, this decontamination process is restricted by the slow transformation of Cu(II)/Cu(I) by PMS. Herein, new N-(L-cysteine/triazine)-O-(carboxymethyl)-chitosan/cobalt ferrate-rice hull hybrid biocomposite was constructed to anchor the mixed-valent Cu(I)-Cu (II) (CuI, II-CCCF) for removing pharmaceutical pollutants (i.e., naproxen, ciprofloxacin, tetracycline, levofloxacin, and paracetamol). The structural, morphological, and catalytic properties of the CuI,II-CCCF have been fully identified by a series of physicochemical characterizations. Results demonstrated that the multifunctional, hydrophilic character, and negative ζ-potential of the activator, accelerating the redox cycle of Cu(II)/Cu(I) with hydroxyl amine (HA). The negligible metal leaching, well-balanced thermodynamic-kinetic properties, and efficient adsorption-catalysis synergy are the main reasons for the significantly enhanced catalytic performance of CuI,II-CCCF in the removal of NPX (98.6 % at 7.0 min). The main active species in the catalytic degradation of NPX were identified (●OH > SO4●- > 1O2 > > O2●-) and consequently suggested a degradation path. It can be noted that these types of carbohydrate-based nanocomposite offer numerous advantages, encompassing simple preparation, excellent decontamination capabilities, and long-term stability.

The escalating threat of human-associated infectious bacteria in surface aquatic resources: Insights into prevalence, antibiotic resistance, survival mechanisms, detection, and prevention strategies

Anthropogenic activities and climate change profoundly impact water quality, leading to a concerning increase in the prevalence and abundance of bacterial pathogens across diverse aquatic environments. This rise has resulted in a growing challenge concerning the safety of water sources, particularly surface waters and marine environments. This comprehensive review delves into the multifaceted challenges presented by bacterial pathogens, emphasizing threads to human health within ground and surface waters, including marine ecosystems. The exploration encompasses the intricate survival mechanisms employed by bacterial pathogens and the proliferation of antimicrobial resistance, largely driven by human-generated antibiotic contamination in aquatic systems. The review further addresses prevalent pathogenic bacteria, elucidating associated risk factors, exploring their eco-physiology, and discussing the production of potent toxins. The spectrum of detection techniques, ranging from conventional to cutting-edge molecular approaches, is thoroughly examined to underscore their significance in identifying and understanding waterborne bacterial pathogens. A critical aspect highlighted in this review is the imperative for real-time monitoring of biomarkers associated with waterborne bacterial pathogens. This monitoring serves as an early warning system, facilitating the swift implementation of action plans to preserve and protect global water resources. In conclusion, this comprehensive review provides fresh insights and perspectives, emphasizing the paramount importance of preserving the quality of aquatic resources to safeguard human health on a global scale.

Occurrence and fate of pharmaceuticals and personal care products in a wastewater treatment plant with Bacillus bio-reactor treatment

Pharmaceuticals and personal care products (PPCPs) have attracted wide attention due to their environmental impacts and health risks. PPCPs released through wastewater treatment plants (WWTPs) are estimated to be 80 %. Nevertheless, the occurrence of PPCPs in the WWTPs equipped with Bacillus spec.-based bioreactors (BBR) treatment system remains unclear. In this study, sludge and waste water samples were collected during separate winter and summer sampling campaigns from a typical BBR treatment system. The results indicate that out of 58 target PPCPs, 27 compounds were detected in the waste water (0.06-1900 ng/L), and 23 were found in the sludge (0.6-7755 ng/g dw). Paraxanthine was the chemical of the highest abundance in the influent due to the high consumption of the parent compounds caffeine and theobromine. The profile for PPCPs in the wastewater and sludge exhibited no seasonal variation. Overall, the removal of target PPCPs in summer is more effective than the winter. In the BBR bio-reactor, it was found that selected PPCPs (at ng/L level) can be completely removed. The efficiency for individual PPCP removal was increased from 1.0 % to 50 % in this unit, after target specific adjustments of the process. The effective removal of selected PPCPs by the BBR treatment system is explained by combined sorption and biodegradation processing. The re-occurrence of PPCPs in the wastewater was monitored. Negative removal efficiency was explained by the cleavage of Phase II metabolites after the biotransformation process, and the lack of equilibrium for PPCPs in the sludge of the second clarifier. A compound specific risk quotient (RQ) was calculated and applied for studying the potential environmental risks. Diphenhydramine is found with the highest environmental risk in wastewater, and 15 other PPCPs show negligible risks in sewage sludge.

Modeling and optimization of triclosan biodegradation by the newly isolated Bacillus sp. DL4: kinetics and pathway speculation

Triclosan is a widely used antibacterial agent and disinfectant, and its overuse endangered ecological safety and human health. Therefore, reducing residual TCS concentrations in the environment is an urgent issue. Bacillus sp. DL4, an aerobic bacterium with TCS biodegradability, was isolated from pharmaceutical wastewater samples. Response surface methodology (RSM) and artificial neural network (ANN) were carried out to optimize and verify the different condition variables, and the optimal growth conditions of strain DL4 were obtained (35 °C, initial pH 7.31, and 5% v/v). After 48 h of cultivation under the optimal conditions, the removal efficiency of strain DL4 on TCS was 95.89 ± 0.68%, which was consistent with the predicted values from RSM and ANN models. In addition, higher R2 value and lower MSE and ADD values indicated that the ANN model had a stronger predictive capability than the RSM model. Whole genome sequencing results showed that many functional genes were annotated in metabolic pathways related to TCS degradation (e.g., amino acid metabolism, xenobiotics biodegradation and metabolism, carbohydrate metabolism). Main intermediate metabolites were identified during the biodegradation process by liquid chromatography-mass spectrometry (LC-MS), and a possible pathway was hypothesized based on the metabolites. Overall, this study provides a theoretical foundation for the characterization and mechanism of TCS biodegradation in the environment by Bacillus sp. DL4.

Microalgal multiomics-based approaches in bioremediation of hazardous contaminants

The enhanced industrial growth and higher living standards owing to the incessant population growth have caused heightened production of various chemicals in different manufacturing sectors globally, resulting in pollution of aquatic systems and soil with hazardous chemical contaminants. The bioremediation of such hazardous pollutants through microalgal processes is a viable and sustainable approach. Accomplishing microalgal-based bioremediation of polluted wastewater requires a comprehensive understanding of microalgal metabolic and physiological dynamics. Microalgae-bacterial consortia have emerged as a sustainable agent for synergistic bioremediation and metabolite production. Effective bioremediation involves proper consortium functioning and dynamics. The present review highlights the mechanistic processes employed through microalgae in reducing contaminants present in wastewater. It discusses the multi-omics approaches and their advantages in understanding the biological processes, monitoring, and dynamics among the partners in consortium through metagenomics. Transcriptomics, proteomics, and metabolomics enable an understanding of microalgal cell response toward the contaminants in the wastewater. Finally, the challenges and future research endeavors are summarised to provide an outlook on microalgae-based bioremediation.

Occurrence, removal efficiency, and emission of antibiotics in the sewage treatment plants of a low-urbanized basin in China and their impact on the receiving water

Sewage treatment plants (STPs) are primary sources of antibiotics in aquatic environments. However, limited research has been conducted on antibiotic attenuation in STPs and their downstream waters in low-urbanized areas. This study analyzed 15 antibiotics in the STP sewage and river water in the Zijiang River basin to quantify antibiotic transport and attenuation in the STPs and downstream. The results showed that 14 target antibiotics, except leucomycin, were detected in the STP sewage, dominated by amoxicillin (AMOX), ofloxacin, and roxithromycin. The total antibiotic concentration in the influent and effluent ranged from 158 to 1025 ng/L and 99.9 to 411 ng/L, respectively. The removal efficiency of total antibiotics ranged from 54.7 % to 75.7 % and was significantly correlated with total antibiotic concentration in the influent. The antibiotic emission from STPs into rivers was 78 kg/yr and 4.6 g/km2yr in the Zijiang River basin. The total antibiotic concentration downstream of the STP downstream was 23.6 to 213 ng/L and was significantly negatively correlated with the transport distance away from the STP outlets. Antibiotics may pose a high ecological risk to algae and low ecological risk to fish in the basin. The risk of AMOX and ciprofloxacin resistance for organisms in the basin was estimated to be moderate. This study established antibiotic removal and attenuation models in STPs and their downstream regions in a low-urbanized basin, which is important for simulating antibiotic transport in STPs and rivers worldwide.

Current strategies on bioremediation of personal care products and detergents: Sustainability and life cycle assessment

The increased use of personal care products and detergents in modern society has raised concerns about their potential adverse effects on the environment. These products contain various chemical compounds that can persist in water bodies, leading to water pollution and ecological disturbances. Bioremediation has emerged as a promising approach to address these challenges, utilizing the natural capabilities of microorganisms to degrade or remove these contaminants. This review examines the current strategies employed in the bioremediation of personal care products and detergents, with a specific focus on their sustainability and environmental impact. This bioremediation is essential for environmental rejuvenation, as it uses living organisms to detergents and other daily used products. Its distinctiveness stems from sustainable, nature-centric ways that provide eco-friendly solutions for pollution eradication and nurturing a healthy planet, all while avoiding copying. Explores the use of microbial consortia, enzyme-based treatments, and novel biotechnological approaches in the context of environmental remediation. Additionally, the ecological implications and long-term sustainability of these strategies are assessed. Understanding the strengths and limitations of these bioremediation techniques is essential for developing effective and environmentally friendly solutions to mitigate the impact of personal care products and detergents on ecosystems.

Preparation of Cobalt-Nitrogen Co-Doped Carbon Nanotubes for Activated Peroxymonosulfate Degradation of Carbamazepine

Cobalt-nitrogen co-doped carbon nanotubes (Co3@NCNT-800) were synthesized via a facile and economical approach to investigate the efficient degradation of organic pollutants in aqueous environments. This material demonstrated high catalytic efficiency in the degradation of carbamazepine (CBZ) in the presence of peroxymonosulfate (PMS). The experimental data revealed that at a neutral pH of 7 and an initial CBZ concentration of 20 mg/L, the application of Co3@NCNT-800 at 0.2 g/L facilitated a degradation rate of 64.7% within 60 min. Mechanistic investigations indicated that the presence of pyridinic nitrogen and cobalt species enhanced the generation of reactive oxygen species. Radical scavenging assays and electron spin resonance spectroscopy confirmed that radical and nonradical pathways contributed to CBZ degradation, with the nonradical mechanism being predominant. This research presents the development of a novel PMS catalyst, synthesized through an efficient and stable method, which provides a cost-effective solution for the remediation of organic contaminants in water.

Bioprospecting photosynthetic microorganisms for the removal of endocrine disruptor compounds

Endocrine disruption compounds can be found in various daily products, like pesticides, along with cosmetic and pharmaceutical commodities. Moreover, occurrence of EDCs in the wastewater alarms the urgency for their removal before discharge owing to the harmful effect for the environment and human health. Compared to implementation of physical and chemical strategies, cultivation of photosynthetic microorganisms has been acknowledged for their high efficiency and eco-friendly process in EDCs removal along with accumulation of valuable byproducts. During the process, photosynthetic microorganisms remove EDCs via photodegradation, bio-adsorption, -accumulation, and -degradation. Regarding their high tolerance in extreme environment, photosynthetic microorganisms have high feasibility for implementation in wastewater treatment plant. However, several considerations are critical for their scaling up process. This review discussed the potency of EDCs removal by photosynthetic microorganisms and focused on the efficiency, mechanism, challenge, along with the prospect. Details on the mechanism's pathway, accumulation of valuable byproducts, and recent progress in scaling up and application in real wastewater were also projected in this review.

Three-dimensional porous La(OH)3/g-C3N4 adsorption-photocatalytic synergistic removal of tetracycline

La(OH)3/g-C3N4 composites were successfully synthesized via one-step calcination using urea, melamine, and La(NO3)3·nH2O as raw materials, and applied to UV-induced photocatalytic tetracycline (TC) removal. Comprehensive characterization by an X-ray diffraction (XRD), Fourier transform infrared reflection (FT-IR), high-resolution transmission electron microscope (HRTEM), and other techniques analyzed effects of La3+ doping, especially N vacancies and cyano groups as active sites. Compared to pure g-C3N4 and La(OH)3, synthesized La(OH)3/g-C3N4 composites exhibited a three-dimensional porous nanosheet structure with specific surface area of 83.62 m2/g and equilibrium TC adsorption capacity up to 285.59 mg/g; La(OH)3 doping significantly improved composite structure. After dispersing 10 mg La-CN-0.5 photocatalyst in 60 mL 40 mg/L TC solution, TC removal reached 91.08% in 30 min under UV irradiation, exhibiting excellent performance. Additionally, La-CN-0.5 showed significant adsorption-photocatalytic synergism, with the quasi-primary kinetic constant increased by 1.83-fold. The efficiency of high tetracycline (TC) concentration treatment through adsorption photocatalytic degradation by La-CN-0.5 was confirmed by the utilization of free radical trapping and electron spin resonance (ESR) tests. The significant involvement of ∙O2-, ∙OH, and h+ in this process was observed. These findings propose that the prepared La-CN-0.5 material exhibits a unique capability for adsorption photocatalysis, providing a promising approach for the efficient removal of high TC concentrations.

Purple acid phosphatase promoted hydrolysis of organophosphate pesticides in microalgae

When organophosphate pesticides (OPs) are not used and handled in accordance with the current rules and standards, it results in serious threats to the aquatic environment and human health. Phaeodactylum tricornutum is a prospective microalgae-based system for pollutant removal and carbon sequestration. Genetically engineered P. tricornutum, designated as the OE line (endogenously expressing purple acid phosphatase 1 [PAP1]), can utilize organic phosphorus for cellular metabolism. However, the competencies and mechanisms of the microalgae-based system (namely the OE line of P. tricornutum) for metabolizing OPs remain to be addressed. In this study, the OE line exhibited the effective biodegradation competencies of 72.12% and 68.2% for 30 mg L-1 of dichlorvos and 50 mg L-1 of glyphosate, accompanied by synergistic accumulations of biomass (0.91 and 0.95 g L-1) and lipids (32.71% and 32.08%), respectively. Furthermore, the biodiesel properties of the lipids from the OE line manifested a high potential as an alternative feedstock for microalgae-based biofuel production. A plausible mechanism of OPs biodegraded by overexpressed PAP1 is that sufficient inorganic P for adenosine triphosphate and concurrent carbon flux for the reduced form of nicotinamide adenine dinucleotide phosphate biosynthesis, which improved the OP tolerance and biodegradation competencies by regulating the antioxidant system, delaying programmed cell death and accumulating lipids via the upregulation of related genes. To sum up, this study demonstrates a potential strategy using a genetically engineered strain of P. tricornutum to remove high concentrations of OPs with the simultaneous production of biomass and biofuels, which might provide novel insights for microalgae-based pollutant biodegradation.

Removal of contaminants of emerging concern from pig manure in different operation stages of a thin-layer cascade photobioreactor. Relationship with concentrations in microalgae and manure

The performance of a pilot-scale thin-layer cascade photobioreactor, operated in semicontinuous mode, for the removal of veterinary drug residues and other contaminants of emerging concern (CECs) from pig manure has been assessed in six operation stages. Chlorella sp. (70-90%), Scenedesmus sp. (10-25%) and Diatomea (<5%) comprise the microalgae species present during the stages. The global performance to remove the total CEC content in the photobioreactor effluent varied from 62 to 86% on each stage, while an CEC mean amount close to 8% was accumulated in the photobioreactor biomass. A relation with weather conditions was not observed. Elimination ratio was not related to the concentration in the influent which reached up to 8000 ng L-1 for some CECs. As expected, the concentrations of veterinary drugs were higher than those of non-veterinary CECs. The concentrations accumulated in the grown biomass were relative low, lower than 10 ng per fresh g excepting for a few cases. However, statistical data suggested that the linkage of CECs to microalgae biomass boosted their removal from the influent. Furthermore, it was observed that the manure liquid phase contained higher amounts of CECs than the solid phase.

Advanced oxidation and biological integrated processes for pharmaceutical wastewater treatment: A review

The stress of pharmaceutical and personal care products (PPCPs) discharging to water bodies and the environment due to increased industrialization has reduced the availability of clean water. This poses a potential health hazard to animals and human life because water contamination is a great issue to the climate, plants, humans, and aquatic habitats. Pharmaceutical compounds are quantified in concentrations ranging from ng/Lto μg/L in aquatic environments worldwide. According to (Alsubih et al., 2022), the concentrations of carbamazepine, sulfamethoxazole, Lutvastatin, ciprofloxacin, and lorazepam were 616-906 ng/L, 16,532-21635 ng/L, 694-2068 ng/L, 734-1178 ng/L, and 2742-3775 ng/L respectively. Protecting and preserving our environment must be well-driven by all sectors to sustain development. Various methods have been utilized to eliminate the emerging pollutants, such as adsorption and biological and advanced oxidation processes. These methods have their benefits and drawbacks in the removal of pharmaceuticals. Successful wastewater treatment can save the water bodies; integrating green initiatives into the main purposes of actor firms, combined with continually periodic awareness of the current and potential implications of environmental/water pollution, will play a major role in water conservation. This article reviews key publications on the adsorption, biological, and advanced oxidation processes used to remove pharmaceutical products from the aquatic environment. It also sheds light on the pharmaceutical adsorption capability of adsorption, biological and advanced oxidation methods, and their efficacy in pharmaceutical concentration removal. A research gap has been identified for researchers to explore in order to eliminate the problem associated with pharmaceutical wastes. Therefore, future study should focus on combining advanced oxidation and adsorption processes for an excellent way to eliminate pharmaceutical products, even at low concentrations. Biological processes should focus on ideal circumstances and microbial processes that enable the simultaneous removal of pharmaceutical compounds and the effects of diverse environments on removal efficiency.

Catalytic PMS oxidation universality of CuFe2O4/MnO2 heterojunctions at multiple application scenarios

The magnetic CuFe2O4/MnO2 heterojunctions were prepared by hydrothermal method, and the effect of different reaction temperature on the physicochemical properties and catalytic activity was investigated. The CuFe2O4/MnO2 heterojunctions prepared at 100 °C can effectively activate peroxymonosulfate (PMS) at multiple application scenarios for degradation and mineralization of tetracycline, o-nitrophenol and ceftriaxone sodium under indoor light, visible light and dark condition. Additionally, the CuFe2O4/MnO2-PMS system showed high catalytic activity and anti-interference ability for degradation of pharmaceutical pollutants in natural water bodies and industrial wastewater. The TC removal efficiency in Qianhu Lake water, Ganjiang River water and tap water was about 88%, 92% and 89%, respectively. The CuFe2O4/MnO2-PMS system is also effective for actual pharmaceutical wastewater treatment with 77.9% of COD removal efficiency. Interestingly, the reactive species of CuFe2O4/MnO2-PMS system under visible light are different from those in dark condition, and the different catalytic mechanisms at multiple application scenarios were proposed. This work provides new insights into mechanism exploration of heterojunction catalyst for PMS activation.

Impact of mixed microalgal and bacterial species on organic micropollutants removal in photobioreactors under natural light

Single microalgae species are effective at the removal of various organic micropollutants (OMPs), however increased species diversity might enhance this removal. Sixteen OMPs were added to 2 continuous photobioreactors, one inoculated with Chlorella sorokiniana and the other with a microalgal-bacterial community, for 112 d under natural light. Three media were sequentially used in 3 Periods: I) synthetic sewage (d 0-28), II) 10x diluted anaerobically digested black water (AnBW) (d 28-94) and III) 5x diluted AnBW (d 94-112). Twelve OMPs were removed > 30 %, while 4 were < 10 % removed. Removal efficiencies were similar for 9 OMPs, yet the mixed community showed a 2-3 times higher removal capacity (µg OMP/g dry weight) than C. sorokiniana during Period II pseudo steady state. The removal decreased drastically in Period III due to overgrowth of filamentous green algae. This study shows for the first time how microbial community composition and abundance are key for OMPs removal.

Antibiotic occurrence, environmental risks, and their removal from aquatic environments using microalgae: Advances and future perspectives

Antibiotic pollution has caused a continuous increase in the development of antibiotic-resistant bacteria and antibiotic-resistant genes (ARGs) in aquatic environments worldwide. Algae-based bioremediation technology is a promising eco-friendly means to remove antibiotics and highly resistant ARGs, and the generated biomass can be utilized to produce value-added products of industrial significance. This review discussed the prevalence of antibiotics and ARGs in aquatic environments and their environmental risks to non-target organisms. The potential of various microalgal species for antibiotic and ARG removal, their mechanisms, strategies for enhanced removal, and future directions were reviewed. Antibiotics can be degraded into non-toxic compounds in microalgal cells through the action of extracellular polymeric substances, glutathione-S-transferase, and cytochrome P450; however, antibiotic stress can alter microalgal gene expression and growth. This review also deciphered the effect of antibiotic stress on microalgal physiology, biomass production, and biochemical composition that can impact their commercial applications.

A computational investigation of DMSO/water separation through functionalized GO multilayer nanosheet membrane using molecular dynamics simulation and deep neural network model for membrane performance prediction

In this molecular dynamics (MD) simulation study, the separation of dimethyl sulfoxide (DMSO) from water was investigated using multilayer functionalized graphene oxide (GO) membranes. The GO nanosheets were modified with chemical groups (-F, -H) to alter their properties. The study analyzed the influence of pressure and functional groups on the separation rate. Additionally, a deep neural network (DNN) model was developed to predict membrane behavior under different conditions in water treatment processes. Results revealed that the fluorine-functionalized membrane exhibited higher permeation compared to the hydrogen-functionalized one, with potential of mean force (PMF) analysis indicating higher energy barriers for water molecules passing through the hydrogen-functionalized membrane. The study used density profile, water density map analysis, and radial distribution function (RDF) analysis to understand water and DMSO molecule interactions. The diffusion coefficient of water molecules was also calculated, showing higher diffusion in the fluorine-functionalized system. Overall, the findings suggest that functionalized GO membranes are effective for DMSO-water separation, with the fluorine-functionalized membrane showing superior performance. The DNN model accurately predicts membrane behavior, contributing to the optimization of membrane separation systems.

Recent advances in remediation strategies for mitigating the impacts of emerging pollutants in water and ensuring environmental sustainability

The proliferation of emerging pollutants (EPs), encompassing a range of substances such as phthalates, phenolics, pharmaceuticals, pesticides, personal care products, surfactants, and disinfection agents, has become a significant global concern due to their potential risks to the environment and human well-being. Over the past two decades, numerous research studies have investigated the presence of EPs in wastewater and aquatic ecosystems, with the United States Environmental Protection Agency (USEPA) categorizing these newly introduced chemical compounds as emerging contaminants due to their poorly understood impact. EPs have been linked to adverse health effects in humans, including genotoxic and cytotoxic effects, as well as conditions such as obesity, diabetes, cardiovascular disease, and reproductive abnormalities, often associated with their estrogenic action. Microalgae have shown promise in the detoxification of both inorganic and organic contaminants, and several large-scale microalgal systems for wastewater treatment have been developed. However, the progress of algal bioremediation can be influenced by accidental contaminations and operational challenges encountered in pilot-scale research. Microalgae employ various processes, such as bioadsorption, biouptake, and biodegradation, to effectively remediate EPs. During microalgal biodegradation, complex chemical compounds are transformed into simpler substances through catalytic metabolic degradation. Integrating algal bioremediation with existing treatment methodologies offers a viable approach for efficiently eliminating EPs from wastewater. This review focuses on the use of algal-based biological remediation processes for wastewater treatment, the environmental impacts of EPs, and the challenges associated with implementing algal bioremediation systems to effectively remove emerging pollutants.

Enhanced Biofilm Formation by Tetracycline in a Staphylococcus aureus Naturally Lacking ica Operon and atl

Staphylococcus aureus is a major, widespread pathogen, and its biofilm-forming characteristics make it even more difficult to eliminate by biocides. Tetracycline (TCY) is a major broad-spectrum antibiotic, the residues of which can cause deleterious health impacts, and subinhibitory concentrations of TCY have the potential to increase biofilm formation in S. aureus. In this study, we showed how the biofilm formation of S. aureus 123786 is enhanced in the presence of TCY at specific subinhibitory concentrations. S. aureus 123786 used in this study was identified as Staphylococcal Cassette Chromosome mec III, sequence type239 and naturally lacking ica operon and atl gene. Two assays were performed to quantify the formation of S. aureus biofilm. In the crystal violet (CV) assay, the absorbance values of biofilm stained with CV at optical density (OD)540 nm increased after 8 and 16 hr of incubation when the concentration of TCY was 1/2 minimum inhibitory concentration (MIC), whereas at the concentration of 1/16 MIC, the absorbance values increased after 16 and 24 hr of incubation. In tetrazolium salt reduction assay, the absorbance value at OD490 nm of S. aureus 123786 biofilms mixed with 3-(4,5-dimethylthiazol-2-yl)-5-(3-carboxymethoxyphenyl)-2-(4-sulfophenyl)-2H-tetrazolium solution increased after 8 hr when the concentration of TCY was 1/4 MIC, which may be correlated with the higher proliferation and maturation of biofilm. In conclusion, the biofilm formation of S. aureus 123786 could be enhanced in the presence of TCY at specific subinhibitory concentrations.

Removal of fluorouracil from aqueous environment using magnetite graphene oxide modified with γ-cyclodextrin

Fluorouracil (FU) is a widely utilized antineoplastic medication in the pharmaceutical industry for combating gastrointestinal cancers. However, its presence in wastewater originating from pharmaceutical facilities and hospital effluents has a potential effect on DNA, and cannot be efficiently eliminated through conventional treatment methods. Consequently, the adoption of advanced technologies becomes crucial for effectively treating such wastewater. Accordingly, this study investigated the efficiency of magnetite graphene oxide nanocomposite functionalized with γ-cyclodextrin for removing fluorouracil from aqueous solutions. The magnetite graphene oxide nanocomposite functionalized with γ-cyclodextrin was synthesized via the hydrothermal method. Next, the effect of pH, temperature, adsorbent content, and contact time on the fluorouracil removal efficiency was explored. Ultimately, the experimental data were matched against Langmuir, Freundlich, and Temkin isotherms and Kinetic models. Accordingly, the efficiency of the absorbent used was dependent on the pH, contact time, temperature, and initial concentration of the adsorbent. The results indicated that the maximum removal efficiency for fluorouracil was achieved within the contact time of 45 min and adsorbent content of 0.020 g. In addition, the optimal pH for removing the medicine was 7. The conditions of the adsorption process followed Langmuir isotherm with correlation coefficients of 0.992 and a quasi-second kinetic model with a correlation coefficient of 0.999, with the maximum adsorption capacity of the adsorbent synthesized for the evaluated medicine estimated as 190.9 mg/g. The results showed that the magnetite graphene oxide nanocomposite functionalized with γ-cyclodextrin could be used as an effective and available adsorbent for removing fluorouracil from pharmaceutical wastewater.

Functionalization strategies of metal-organic frameworks for biomedical applications and treatment of emerging pollutants: A review

One of the representative coordination polymers, metal-organic frameworks (MOFs) material, is of hotspot interest in the multi field thanks to their unique structural characteristics and properties. As a novel hierarchical structural class, MOFs show diverse topologies, intrinsic behaviors, flexibility, etc. However, bare MOFs have less desirable biofunction, high humid sensitivity and instability in water, restraining their efficiencies in biomedical and environmental applications. Thus, a structural modification is required to address such drawbacks. Herein, we pinpoint new strategies in the synthesis and functionalization of MOFs to meet demanding requirements in in vitro tests, i.e., antibacterial face masks against corona virus infection and in wound healing and nanocarriers for drug delivery in anticancer. Regarding the treatment of wastewater containing emerging pollutants such as POPs, PFAS, and PPCPs, functionalized MOFs showed excellent performance with high efficiency and selectivity. Challenges in toxicity, vast database of clinical trials for biomedical tests and production cost can be still presented. MOFs-based composites can be, however, a bright candidate for reasonable replacement of traditional nanomaterials in biomedical and wastewater treatment applications.

Unraveling the combined toxicity and removal mechanisms of fluoxetine and sertraline co-contaminants by the freshwater microalga Chlorella pyrenoidosa

Selective serotonin reuptake inhibitors (SSRIs), such as fluoxetine (FLX) and sertraline (SER), are among the most widely detected pharmaceuticals in aquatic environments, and they usually occur as mixtures. However, little is known about the combined toxicity of SSRI mixtures to microalgae and the associated removal mechanisms. This study investigated the combined toxicity of FLX and SER to the growth, photosynthetic activity, and antioxidant system of Chlorella pyrenoidosa and their removal mechanisms. The results showed that FLX and SER strongly inhibited microalgal growth with 96 h EC50 values of 493 and 61.1 μg/L, respectively. Additionally, the combined toxicity of FLX and SER towards microalgal growth exhibited an additive effect. After 4 days of short-term exposure, FLX, SER, and their mixtures caused photosynthetic damage and oxidative stress in microalgae, and the mixture's toxicity was stronger than those of individuals. However, the adverse effects on microalgal growth, photosynthetic activity, and antioxidant system were alleviated with increasing exposure time. Meanwhile, C. pyrenoidosa efficiently removed FLX (67.59%-99.08%) and SER (94.92%-99.11%) individually after 11 days of cultivation. Biodegradation (59.25%-86.21%) was the prominent removal mechanism of FLX, while both biodegradation (48.08%-88.17%) and bioaccumulation (4.74%-43.38%) contributed significantly to SER removal. The co-existence of FLX and SER lowered the removal rate and biodegradation amount of both compounds. Besides, SER inhibited C. pyrenoidosa's N-demethylation and O-dealkylation of FLX, while co-existing with FLX inhibited the excretion of the N-deamination product of SER from microalgal cells. Furthermore, the principal component analysis indicated that the removal performance of FLX, SER, and their mixtures correlated strongly to the microalgae's physiological and biochemical states. These results highlighted the significance of co-contamination during ecological risk assessments and microalgae-based bioremediation of SSRIs.

Effects of light quality on microalgae cultivation: bibliometric analysis, mini-review, and regulation approaches

The ever-increasing concern for energy shortages and greenhouse effect has triggered the development of sustainable green technologies. Microalgae have received more attention due to the characteristics of biofuel production and CO2 fixation. From the perspective of autotrophic growth, the optimization of light quality has the potential to promote biomass production and bio-component accumulation in microalgae at low cost. In this study, bibliometric analysis was used to describe the basic features, identify the hotspots, and predict future trends of the research related to the light quality on microalgae cultivation. In addition, a mini-review referring to regulation methods of light quality was provided to optimize the framework of research. Results demonstrated that China has the greatest interest in this area. The destination of most research was to obtain biofuels and high-value-added products. Both blue and red lights were identified as the crucial spectrums for microalgae cultivation. However, sunlight is the most affordable light resource, which could not be fully utilized by microalgae through the photosynthetic process. Hence, some regulation approaches (e.g., dyes, plasmonic scattering, and carbon-based quantum dots) are proposed to increase the proportion of beneficial spectrum for enhancement of photosynthetic efficiency. In summary, this review introduces state-of-the-art research and provides theoretical guidance for light quality optimization in microalgae cultivation to obtain more benefits.

Realization process of microalgal biorefinery: The optional approach toward carbon net-zero emission

Increasing carbon dioxide (CO2) emission has already become a dire threat to the human race and Earth's ecology. Microalgae are recommended to be engineered as CO2 fixers in biorefinery, which play crucial roles in responding climate change and accelerating the transition to a sustainable future. This review sorted through each segment of microalgal biorefinery to explore the potential for its practical implementation and commercialization, offering valuable insights into research trends and identifies challenges that needed to be addressed in the development process. Firstly, the known mechanisms of microalgal photosynthetic CO2 fixation and the approaches for strain improvement were summarized. The significance of process regulation for strengthening fixation efficiency and augmenting competitiveness was emphasized, with a specific focus on CO2 and light optimization strategies. Thereafter, the massive potential of microalgal refineries for various bioresource production was discussed in detail, and the integration with contaminant reclamation was mentioned for economic and ecological benefits. Subsequently, economic and environmental impacts of microalgal biorefinery were evaluated via life cycle assessment (LCA) and techno-economic analysis (TEA) to lit up commercial feasibility. Finally, the current obstacles and future perspectives were discussed objectively to offer an impartial reference for future researchers and investors.

Microbial approaches for pharmaceutical wastewater recycling and management for sustainable development: A multicomponent approach

A microbial-driven approach for effluent treatment, recycling, and management of Pharmaceutical and Personal Care Products (PPCPs) has been undertaken to mitigate the menace of water contamination. Bioremediation processes are mainly considered the first preference in pharmaceutical wastewater recycling and management. PPCPs are reported as one of the primary sources of emerging contaminants in various water matrices, which raises concern and requires efficient management. Their widespread utilization, persistently high level, and resistance to breaking down make them one of the potentially dangerous compounds causing harm to the ecosystem. Continually increasing PPCPs level PPCPs contaminants in water bodies raised concern for human health as they can produce potential risks with harmful and untoward impacts on our health. PPCPs are composed of multiple diverse compounds used by humans and animals, which include biopharmaceuticals, vitamins and nutritional supplements, antibiotics, counter-prescription drugs, cosmetics products, and unused pharmaceutical products. Personal care products are found to be bioaccumulative, reduce water quality and potentially impact ecological health. However, continual exposure to PPCPs in aquatic organisms, impacts their endocrine function disruption, gene toxicity, and antibiotic resistance. Decreased water quality may result in an outbreak of various water-borne diseases, which could have acute or long-term health complications and may result in an outbreak of various water-borne diseases, which could have acute or long-term effects on public and community health. Polluted water consumption by humans and animals produces serious health hazards and increased susceptibility to water-borne diseases such as carcinogenic organic or inorganic contaminants and infectious pathogens present in water bodies. Many water resource recovery facilities working on various conventional and advanced methods involve the utilization of microbes for filtration and advanced oxidation processes. Therefore, there is an immense need for bioremediation techniques facilitated by mixed cultures of bacteria, algae, and other microbes that can be used as an alternative approach for removing pharmaceutical content from effluent. This review highlights the various sources of PPCPs and their impacts on soil and water bodies, resulting in bioaccumulation. Different techniques are utilized to detect PPCPs, and various control strategies imply controlling, recycling, and managing waste.

Microalgal-based bioremediation of emerging contaminants: Mechanisms and challenges

Emerging contaminants (ECs) in different ecosystems have consistently been acknowledged as a global issue due to toxicity, human health implications, and potential role in generating and disseminating antimicrobial resistance. The existing wastewater treatment system is incompetent at eliminating ECs since the effluent water contains significant concentrations of ECs, viz., antibiotics (0.03-13.0 μg L-1), paracetamol (50 μg L-1), and many others in varying concentrations. Microalgae are considered as a prospective and sustainable candidate for mitigating of ECs owing to some peculiar features. In addition, the microalgal-based processes also offer cost and energy-efficient solutions for the bioremediation of ECs than conventional treatment systems. It is pertinent that, microalgal-based processes also provides waste valorization benefits as microalgal biomass obtained after ECs treatment can be potentially applied to generate biofuels. Moreover, microalgae can effectively utilize alternative metabolic (cometabolism) routes for enhanced degradation of ECs. Additionally, the ECs removal via the microalgal biodegradation route is highly promising as it can transform the ECs into less toxic compounds. The present review comprehensively discusses different mechanisms involved in removing ECs and various factors that affect their removal. Also, the technoeconomic feasibility of microalgae than other conventional wastewater treatment methods is summarised. The review also highlighted the different molecular and genetic tools that can augment the activity and robustness of microalgae for better removal of organic contaminants. Finally, we have summarised the challenges and future research required towards microalgal-based bioremediation of emerging contaminants (ECs) as a holistic approach.

Pharmaceutical and personal care products (PPCPs) degradation and microbial characteristics of low-temperature operation combined with constructed wetlands

Emerging contaminants (ECs), which are present in water bodies, could cause global environmental and human health problems. These contaminants originate from various sources such as hospitals, clinics, households, and industries. Additionally, they can also indirectly enter the water supply through runoff from agriculture and leachate from landfills. ECs, specifically Pharmaceutical and personal care products (PPCPs), are causing widespread concern due to their contribution to persistent water pollution. Traditional approaches often involve expensive chemicals and energy or result in the creation of by-products. This study developed a practical and environmentally-friendly method for removing PPCPs, which involved combining and integrating various techniques. To implement this method, it was necessary to establish and used a field simulator based on the real-life scenario. Based on the data analysis, the average removal rates of COD, TP, TN, and NH4+-N were 57%, 59%, 63%, and 73%, respectively. the removal rate of PPCPs by CCWs was found to be 82.7% after comparing samples that were not treated by constructed wetlands and those that were treated. Combined constructed wetlands (CCWs) were found to effectively remove PPCPs from water. This is due to the combined action of plant absorption, absorption, and biodegradation by microorganisms living in the wetlands. Interestingly, the wetland plant reed had been shown to play an important role in removing these pollutants. Microbial degradation was the most important pathway for PPCPs removal in CCWs. Carbamazepine was selected as a typical PPCP for analysis. In addition, the microbial community structure of the composite filler was also investigated. High-throughput sequencing confirmed that the dominant bacteria had good adaptability to PPCPs. This technique not only reduced the potential environmental impact but also served as a foundation for further research on the use of constructed wetlands for the treatment of PPCPs contaminated water bodies and its large-scale implementation.

Chlorphenamine adsorption on commercial activated carbons: Effect of Operating Conditions and Surface Chemistry

Chlorphenamine (CPA) adsorption onto three activated carbons (ACs), namely, Megapol M (MM), Micro 10 (M10), and GAMA B (GB), was studied in this work. The textural properties, concentrations of active sites, surface charge and point of zero charge of the ACs were assessed. The surface areas (SBET) of MM, GB and M10 were 1107, 812 and 766 m2/g, respectively. The MM surface had an acidic character, while the surfaces of M10 and GB were basic. The adsorption capacity of MM, M10, and GB towards CPA was studied at pH 7 and 11, and the adsorption capacity decreased in the order MM > M10 ≈ GB, which was ascribed to the magnitude of SBET and the concentration of acidic sites. The solution pH significantly increased the adsorption capacity of MM towards CPA by raising the solution pH from 5 to 9, and this behavior was attributed to the electrostatic attraction between the negatively charged surface of MM and the cationic species of CPA. The maximum uptake of CPA adsorbed on MM was 574.6 mg/g at pH = 11 and T = 25 °C. The adsorption capacity of MM was slightly raised by incrementing the temperature. Lastly, the zeta potential measurements of pristine MM and MM saturated with CPA confirmed that the electrostatic attraction predominated in the pH range of 5-9, and the π-π stacking interactions were the principal mechanism of CPA adsorption on MM at pH 11.

Removal of organic and inorganic contaminants from the air, soil, and water by algae

Rapid increases in human populations and development has led to a significant exploitation of natural resources around the world. On the other hand, humans have come to terms with the consequences of their past mistakes and started to address current and future resource utilization challenges. Today's primary challenge is figuring out and implementing eco-friendly, inexpensive, and innovative solutions for conservation issues such as environmental pollution, carbon neutrality, and manufacturing effluent/wastewater treatment, along with xenobiotic contamination of the natural ecosystem. One of the most promising approaches to reduce the environmental contamination load is the utilization of algae for bioremediation. Owing to their significant biosorption capacity to deactivate hazardous chemicals, macro-/microalgae are among the primary microorganisms that can be utilized for phytoremediation as a safe method for curtailing environmental pollution. In recent years, the use of algae to overcome environmental problems has advanced technologically, such as through synthetic biology and high-throughput phenomics, which is increasing the likelihood of attaining sustainability. As the research progresses, there is a promise for a greener future and the preservation of healthy ecosystems by using algae. They might act as a valuable tool in creating new products.

Regulation and role of extracellular polymeric substances in the defensive responses of Dictyosphaerium sp. to enrofloxacin stress

Algae are susceptible to enrofloxacin (ENR), an antibiotic frequently detected in aquatic environments. However, algal responses, especially the secretion and roles of extracellular polymeric substances (EPS), under ENR exposure remain unknown. This study is the first to elucidate the variation in algal EPS triggered by ENR at both the physiological and molecular levels. The results showed that EPS were significantly (P < 0.05) overproduced along with increased polysaccharide and protein contents in algae exposed to 0.05, 0.5, and 5 mg/L ENR. Secretion of aromatic proteins, especially tryptophan-like substances with more functional groups or aromatic rings, was specifically stimulated. Furthermore, the genes with upregulated expression related to carbon fixation, aromatic protein biosynthesis, and carbohydrate metabolism are direct causes of enhanced EPS secretion. Improved EPS levels increased the cell surface hydrophobicity and provided more adsorption sites for ENR, which strengthened the van der Waals interaction and reduced ENR internalization. The hormesis effects of ENR were alleviated, as illustrated by the less affected cell density, chlorophyll a/b, and carotenoids biosynthesis in algae with EPS. These findings demonstrate the involvement of EPS in algal ENR resistance and promote a deeper understanding of the ecological effects of ENR in aquatic environments.

Spatiotemporal distribution and ecological risk assessment of pharmaceuticals and personal care products (PPCPs) from Luoma Lake, an important node of the South-to-North Water Diversion Project

PPCPs (pharmaceuticals and personal care products) are widely found in the environment and can be a risk to human and ecosystem health. In this study, spatiotemporal distribution, critical risk source identification and potential risks of 14 PPCPs found in water collected from sampling points in Luoma Lake and its inflowing rivers in two seasons in 2019 and 2020 were investigated. The PPCPs concentrations ranged from 27.64 ng·L-1 to 613.08 ng·L-1 in December 2019, and from 16.67 ng·L-1 to 3287.41 ng·L-1 in April 2020. Ketoprofen (KPF) dominated the PPCPs with mean concentrations of 125.85 ng·L-1 and 640.26 ng·L-1, respectively. Analysis of sources showed that the pollution in Luoma Lake mostly originated from sewage treatment plant effluents, inflowing rivers and domestic wastewater. Among them, the inflowing rivers contributed the most (82.95%) to the concentration of total PPCPs. The results of ecological risk assessment showed that there was a moderate risk (0.1 < RQs < 1) from carbamazepine (CBZ) in December 2019 and a high risk (RQs > 1) from naproxen (NPX) in April 2020. The results of human risk assessment found that NPX posed a high risk to infant health, and we found that NPX was associated with 83 diseases according to Comparative Toxicogenomics Database. NPX was identified as a substance requiring major attention. The results provide an understanding of the concentrations and ecological risks of PPCPs in Luoma Lake. We believe the data will support environmental departments to develop management strategies and prevent PPCPs pollution.

A pilot-scale study on the removal of binary mixture (ciprofloxacin and norfloxacin) by Scenedesmus obliquus: Optimization, biotransformation, and biofuel profile

Ciprofloxacin (CIP) and norfloxacin (NOR) belong to the organic contaminants of emerging concern (OCECs) that are frequently detected in wastewater matrices at ng/L to mg/L concentrations. This study investigates the potential of Scenedesmus obliquus in the treatment of CIP and NOR as a binary mixture from raw wastewater. Optimization of inoculum was done to find the required cell density concentration that has less inhibition and high removal. The optimum inoculum (cell density: 200 × 105 cells/mL and OD680: 1.0) has shown 75% removal with no inhibition of growth. A pilot scale study was conducted in controlled environment using high-rate algal pond to investigate the contribution of abiotic and biotic removal. Abiotic removal is negligible in comparison with the biotic contribution of removal. The order of removal efficiency is observed as COD (88%) > NOR (84.8%) > CIP (84.6%) > NH4+ (71.7%) with biodegradation as the major removal mechanism. Biotransformed products of CIP + NOR were identified inside the Scenedesmus obliquus. During the pilot-scale study, Biomass (3.70 ± 0.07 g/L) was harvested with carbohydrates (17.85 ± 0.1%), lipids (38.36 ± 0.13%), and proteins (28.18 ± 1.63%). Lipid productivity in binary mixture was 2.6 times higher than the lipid production in control condition. Transesterification of these lipids yielded good biofuel composition of 32.72% of saturated fatty acids and 21.7% of unsaturated fatty acids.

Amoxicillin degradation and high-value extracellular polymer recovery by algal-bacterial symbiosis systems

Algal-bacterial symbiosis systems have emerged as sustainable methods for the treatment of new pollutants and the recovery of resources. However, the bio-refinery of biomass derived from microalgae is inefficient and expensive. In order to simultaneously degrade antibiotic and recover resources efficiently, two algal-bacterial symbiosis systems were constructed using Pseudomonas aeruginosa (alginate overproduction) and Bacillus subtilis (poly-γ-glutamic acid overproduction) with amoxicillin-degrading-microalga Prototheca zopfii W1. The optimal conditions for W1 to degrade amoxicillin are 35 °C, pH 7, and 180 rpm. In the presence of 5-50 mg/L of amoxicillin, W1-P. aeruginosa and W1-B. subtilis exhibit higher amoxicillin degradation and produce more extracellular polymers than W1 or bacteria alone. The metabolomic analysis demonstrates that the algal-bacterial symbiosis enhances the tolerance of W1 to amoxicillin by altering carbohydrate metabolism and promotes the production of biopolymers by upregulating the precursors synthesis. Moreover, the removal of amoxicillin (10 mg/L) from livestock effluent by W1-P. aeruginosa and W1-B. subtilis is greater than 90 % in 3 days, and the maximum yields of alginate and poly-γ-glutamate are 446.1 and 254.3 mg/g dry cell weight, respectively. These outcomes provide theoretical support for the application of algal-bacterial symbiosis systems to treatment of amoxicillin wastewater and efficient production of biopolymers.

Wastewater treatment by using microalgae: Insights into fate, transport, and associated challenges

The remediation of wastewater with microalgae is a new topic that concentrates on devising a cost-effective and environmentally beneficial method. Multiple microalgae and bacterial consortiums have recently been evaluated to determine if they can purify effluent from various sources. Critical to a system's efficacy is its ability to remove nutrients such as nitrogen (N) and phosphorus (P) and heavy metals such as arsenic (As), lead (Pb), and copper (Cu). This study compared traditional wastewater treatment systems to microalgae-based systems for treating different types of wastewater. The research investigates the potential for microalgae to cleanse wastewater. The research also evaluates wastewater parameters, methods, and scientific techniques for extracting nutrients and heavy metals from polluted water. According to the literature, Microalgae can remove between 98.7% and 100% of nitrogen (N), phosphorous (P), and heavy metals from various effluents. The paper concludes by discussing the difficulties of using microalgae to remediate wastewater. The elimination of nutrients from the effluent is influenced by biomass production, osmotic capacity, temperature, pH, and O2 concentration. Therefore, a "pilot" study is recommended to investigate contaminants.

Optimization and mechanistic approach for removal of crystal violet and methylene blue dyes via activated carbon from pyrolyzed-ZnCl2 bamboo waste

In this study, bamboo waste (BW) was subjected to pyrolysis-assisted ZnCl2 activation to produce mesoporous activated carbon (BW-AC), which was then evaluated for its ability to remove cationic dyes, specifically methylene blue (MB) and crystal violet (CV), from aqueous environments. The properties of BW-AC were characterized using various techniques, including potentiometric-based point of zero charge (pHpzc), scanning electron microscopy with energy dispersive X-rays (SEM-EDX), X-ray diffraction (XRD), gas adsorption with Brunauer-Emmett-Teller (BET) analysis, infrared (IR) spectroscopy. To optimize the adsorption characteristics (BW-AC dosage, pH, and contact time) of PBW, a Box-Behnken design (BBD) was employed. The BW-AC dose of 0.05 g, solution pH of 10, and time of 8 min are identified as optimal operational conditions for achieving maximum CV (89.8%) and MB (96.3%) adsorption according to the BBD model. The dye removal kinetics for CV and MB are described by the pseudo-second-order model. The dye adsorption isotherms revealed that adsorption of CV and MB onto BW-AC follow the Freundlich model. The maximum dye adsorption capacities (qmax) of BW-AC for CV (530 mg/g) and MB (520 mg/g) are favorable, along with the thermodynamics of the adsorption process, which is characterized as endothermic and spontaneous. The adsorption mechanism of CV and MB dyes by BW-AC was attributed to multiple contributions: hydrogen bonding, electrostatic forces, π-π attraction, and pore filling. The findings of this study highlight the potential of BW-AC as an effective adsorbent in wastewater treatment applications, contributing to the overall goal of mitigating the environmental impact of cationic dyes and ensuring the quality of water resources.

Removal of pharmaceuticals and personal care products from wastewater via anodic oxidation and electro-Fenton processes: current status and needs regarding their application

This review provides a current opinion on the most recent works that have been published toward the application of electrochemical advance oxidation processes (EAOPs) for the degradation of pharmaceutical and personal care products (PPCPs) in water streams. Advances in the application of anodic oxidation (AO)- and electro-Fenton (EF)-based processes are reported, including operational conditions, electrode performance, and removal. Although AO- and EF-based processes can easily reach 100% removal of PPCPs, mineralization is desirable to avoid the generation of potential toxic byproducts. The following section exploring some techno-economic aspects of the application of EAOPs is based on electrode selection, operational costs as well as their use as cotreatments, and their synergistic effects. Finally, this short review ends with perspectives about the emerging topics that are faced by these technologies applied for the degradation of PPCPs in research and practice.

An investigation on removal of ciprofloxacin and norfloxacin by phycoremediation with an emphasis on acute toxicity and biochemical composition

Ciprofloxacin (CIP) and norfloxacin (NOR) belong to the class of emerging contaminants that are frequently detected in the aquatic environment as a binary mixture, responsible for the development of antibiotic-resistant genes and antibiotic-resistant bacteria. This study aims to investigate five different algal species Chlorella vulgaris (Cv), Chlorella pyrenoidosa (Cp), Scenedesmus obliquus (So), Tetradesmus sp (T) and Monoraphidium sp (M) for their tolerance and removal of binary mixture. The effects on biochemical composition in the algal species concerning the binary mixture and its removal efficiency are first reported in this study. The acute toxicity (96 h EC50) values are in the order of So > Cp > T > M > Cv, Chlorella vulgaris is the most sensitive algal species with 17.73 ± 0.24 mg/L and Scenedesmus obliquus is the least sensitive algal species with 39.19 ± 0.79 mg/L. The removal efficiency of the binary mixture was found to be in the order of So > Cp > T > M > Cv, Scenedesmus obliquus removed CIP (52.4%) and NOR (87.5%) with biodegradation as the major contributing removal mechanism. Furthermore, less toxic biotransformed products were detected in Scenedesmus obliquus and the biochemical characterization revealed that the growth-stimulating effect is higher with lipid (35%), carbohydrate (18%), and protein (33%) providing an advantage in the production of valuable biomass.

Recent advancements on antibiotic bioremediation in wastewaters with a focus on algae: an overview

Antibiotic contamination from hospitals, animal husbandry, and municipal wastewater is graver than imagined, and it possess serious risks to the health of humans and animals, with the emergence of multidrug resistant bacteria; those affect the growth of higher plants too. Conventional wastewater treatment methods adopted today are inadequate for removing antibiotics from wastewater. Intuitively, the remediation process using mixed algae should be effective enough, for which algae-based remediation technologies have emerged as sustainable remedial methods. This review summarized the detection of antibiotics in field water in most countries; a comprehensive overview of algae-based technologies, algal adsorption, accumulation, biodegradation, photodegradation, hydrolysis, and the use of algae-bacteria consortia for the remediation of antibiotics in wastewaters in done. Green algae namely, Chlamydomonas sp., Chlorella sp., C. vulgaris, Spyrogira sp. Scenedesmus quadricauda, S. obliquus, S. dimorphus, Haematoccus pluvialis, and Nannochlopsis sp., had been reporting have 90-100% antibiotic removal efficiency. The integration of bioelectrochemical systems and genetically engineered prokaryotic algal species offer promising avenues for improving antibiotic removal in the future. Overall, this review highlights the need for tenacious research and development of algae-based technologies to reduce antibiotic contamination in aquatic environments, for holistic good.

Recent perspective of antibiotics remediation: A review of the principles, mechanisms, and chemistry controlling remediation from aqueous media

Antibiotic pollution is an ever-growing concern that affects the growth of plants and the well-being of animals and humans. Research on antibiotics remediation from aqueous media has grown over the years and previous reviews have highlighted recent advances in antibiotics remediation technologies, perspectives on antibiotics ecotoxicity, and the development of antibiotic-resistant genes. Nevertheless, the relationship between antibiotics solution chemistry, remediation technology, and the interactions between antibiotics and adsorbents at the molecular level is still elusive. Thus, this review summarizes recent literature on antibiotics remediation from aqueous media and the adsorption perspective. The review discusses the principles, mechanisms, and solution chemistry of antibiotics and how they affect remediation and the type of adsorbents used for antibiotic adsorption processes. The literature analysis revealed that: (i) Although antibiotics extraction and detection techniques have evolved from single-substrate-oriented to multi-substrates-oriented detection technologies, antibiotics pollution remains a great danger to the environment due to its trace level; (ii) Some of the most effective antibiotic remediation technologies are still at the laboratory scale. Thus, upscaling these technologies to field level will require funding, which brings in more constraints and doubts patterning to whether the technology will achieve the same performance as in the laboratory; and (iii) Adsorption technologies remain the most affordable for antibiotic remediation. However, the recent trends show more focus on developing high-end adsorbents which are expensive and sometimes less efficient compared to existing adsorbents. Thus, more research needs to focus on developing cheaper and less complex adsorbents from readily available raw materials. This review will be beneficial to stakeholders, researchers, and public health professionals for the efficient management of antibiotics for a refined decision.

Impact of wastewater characteristics on the removal of organic micropollutants by Chlorella sorokiniana

Microalgae-based technologies can be used for the removal of organic micropollutants (OMPs) from different types of wastewater. However, the effect of wastewater characteristics on the removal is still poorly understood. In this study, the removal of sixteen OMPs by Chlorella sorokiniana, cultivated in three types of wastewater (anaerobically digested black water (AnBW), municipal wastewater (MW), and secondary clarified effluent (SCE)), were assessed. During batch operational mode, eleven OMPs were removed from AnBW and MW. When switching from batch to continuous mode (0.8 d HRT), the removal of most OMPs from AnBW and MW decreased, suggesting that a longer retention time enhances the removal of some OMPs. Most OMPs were not removed from SCE since poor nutrient availability limited C. sorokiniana growth. Further correlation analyses between wastewater characteristics, biomass and OMPs removal indicated that the wastewater soluble COD and biomass concentration predominantly affected the removal of OMPs. Lastly, carbon uptake rate had a higher effect on the removal of OMPs than nitrogen and phosphate uptake rate. These data will give an insight on the implementation of microalgae-based technologies for the removal of OMPs in wastewater with varying strengths and nutrient availability.

Efficient mitigation of emerging antibiotics residues from water matrix: Integrated approaches and sustainable technologies

The prevalence of antibiotic traces in the aquatic matrices is a concern due to the emanation of antibiotic resistance which requires a multifaceted approach. One of the potential sources is the wastewater treatment plants with a lack of advance infrastructure leading to the dissemination of contaminants. Continuous advancements in economic globalization have facilitated the application of several conventional, advanced, and hybrid techniques for the mitigation of rising antibiotic traces in the aquatic matrices that have been thoroughly scrutinized in the current paper. Although the implementation of existing mitigation techniques is associated with several limiting factors and barriers which require further research to enhance their removal efficiency. The review further summarizes the application of the microbial processes to combat antibiotic persistence in wastewater establishing a sustainable approach. However, hybrid technologies are considered as most efficient and environmental-benign due to their higher removal efficacy, energy-efficiency, and cost-effectiveness. A brief elucidation has been provided for the mechanism responsible for lowering antibiotic concentration in wastewater through biodegradation and biotransformation. Overall, the current review presents a comprehensive approach for antibiotic mitigation using existing methods however, policies and measures should be implemented for continuous monitoring and surveillance of antibiotic persistence in aquatic matrices to reduce their potential risk to humans and the environment.

New insights into the bioremediation of petroleum contaminants: A systematic review

Petroleum product is an essential resource for energy, that has been exploited by wide range of industries and regular life. A carbonaceous contamination of marine and terrestrial environments caused by errant runoffs of consequential petroleum-derived contaminants. Additionally, petroleum hydrocarbons can have adverse effects on human health and global ecosystems and also have negative demographic consequences in petroleum industries. Key contaminants of petroleum products, primarily includes aliphatic hydrocarbons, benzene, toluene, ethylbenzene, and xylene (BTEX), polycyclic aromatic hydrocarbons (PAHs), resins, and asphaltenes. On environmental interaction, these pollutants result in ecotoxicity as well as human toxicity. Oxidative stress, mitochondrial damage, DNA mutations, and protein dysfunction are a few key causative mechanisms behind the toxic impacts. Henceforth, it becomes very evident to have certain remedial strategies which could help on eliminating these xenobiotics from the environment. This brings the efficacious application of bioremediation to remove or degrade pollutants from the ecosystems. In the recent scenario, extensive research and experimentation have been implemented towards bio-benign remediation of these petroleum-based pollutants, aiming to reduce the load of these toxic molecules in the environment. This review gives a detailed overview of petroleum pollutants, and their toxicity. Methods used for degrading them in the environment using microbes, periphytes, phyto-microbial interactions, genetically modified organisms, and nano-microbial remediation. All of these methods could have a significant impact on environmental management.

Semirigid Highly Conjugated Zirconium-Organic Framework for the Capture of Micropollutants and Solar-Light Photodegradation

Micro-organic pollutants, particularly organic dyes and personal care products (PPCPs), are widely present in wastewater, and thus pose a serious risk to human health. The capture and solar-light photodegradation of micro-organic pollutants are highly challenging tasks, which require the design and synthesis of microporous materials with specific structures. As we know, organic dyes and PPCPs can be absorbed via π-π* stacking. In this paper, an iron-based metal-organic framework (Fe-UiO-68-terNap) containing semirigid conjugated aromatic ligands is prepared for the capture and solar-light photodegradation of multiple water contaminants. UiO-68-terNap was synthesized based on ternaphthalene with π-π* stacking, which would increase the adsorption capacities of organic micropollutants in wastewater. Additionally, the formation of Fe-O-Zr enhances the charge-separation ability resulting in the successful degradation of micropollutants in 240 min. The novel material has been elucidated by single-crystal X-ray diffraction and Fe K-edge XANES, which provide key insights at a molecular level for the design of novel materials for the capture and photodegradation of organic micropollutants.

Preparation of a Series of Highly Efficient Porous Adsorbent PGMA-N Molecules and Its Application in the Co-Removal of Cu(II) and Sulfamethoxazole from Water

This paper presents a highly efficient porous adsorbent PGMA-N prepared through a series of amination reactions between polyglycidyl methacrylate (PGMA) and different polyamines. The obtained polymeric porous materials were characterized using Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), specific surface area test (BET), and elemental analysis (EA). Thereinto, the PGMA-EDA porous adsorbent exhibited excellent ability to synergistically remove Cu(II) ions and sulfamethoxazole from aqueous solutions. Moreover, we studied the effects of pH, contact time, temperature, and initial concentration of pollutants on the adsorption performance of the adsorbent. The experimental results showed that the adsorption process of Cu(II) followed the pseudo-second-order kinetic model and Langmuir isotherm. The maximum adsorption capacity of PGMA-EDA for Cu(II) ions was 0.794 mmol/g. These results indicate that PGMA-EDA porous adsorbent has great potential for application in treating wastewater coexisting with heavy metals and antibiotics.