Biodegradable and re-usable sponge materials made from chitin for efficient removal of microplastics

A critical review of microplastics in aquatic ecosystems: Degradation mechanisms and removing strategies

Plastic waste discarded into aquatic environments gradually degrades into smaller fragments, known as microplastics (MPs), which range in size from 0.05 to 5 mm. The ubiquity of MPs poses a significant threat to aquatic ecosystems and, by extension, human health, as these particles are ingested by various marine organisms including zooplankton, crustaceans, and fish, eventually entering the human food chain. This contamination threatens the entire ecological balance, encompassing food safety and the health of aquatic systems. Consequently, developing effective MP removal technologies has emerged as a critical area of research. Here, we summarize the mechanisms and recently reported strategies for removing MPs from aquatic ecosystems. Strategies combining physical and chemical pretreatments with microbial degradation have shown promise in decomposing MPs. Microorganisms such as bacteria, fungi, algae, and specific enzymes are being leveraged in MP remediation efforts. Recent advancements have focused on innovative methods such as membrane bioreactors, synthetic biology, organosilane-based techniques, biofilm-mediated remediation, and nanomaterial-enabled strategies, with nano-enabled technologies demonstrating substantial potential to enhance MP removal efficiency. This review aims to stimulate further innovation in effective MP removal methods, promoting environmental and social well-being.

Activating Adsorption Sites of Waste Crayfish Shells via Chemical Decalcification for Efficient Capturing of Nanoplastics

The property of being stubborn and degradation resistant makes nanoplastic (NP) pollution a long-standing remaining challenge. Here, we apply a designed top-down strategy to leverage the natural hierarchical structure of waste crayfish shells with exposed functional groups for efficient NP capture. The crayfish shell-based organic skeleton with improved flexibility, strength (14.37 to 60.13 MPa), and toughness (24.61 to 278.98 MJ m-3) was prepared by purposefully removing the inorganic components of crayfish shells through a simple two-step acid-alkali treatment. Due to the activated functional groups (e.g., -NH2, -CONH-, and -OH) and ordered architectures with macropores and nanofibers, this porous crayfish shell exhibited effective removal capability of NPs (72.92 mg g-1) by physical interception and hydrogen bond/electrostatic interactions. Moreover, the sustainability and stability of this porous crayfish shell were demonstrated by the maintained high-capture performance after five cycles. Finally, we provided a postprocessing approach that could convert both porous crayfish shell and NPs into a tough flat sheet. Thus, our feasible top-down engineering strategy combined with promising posttreatment is a powerful contender for a recycling approach with broad application scenarios and clear economic advantages for simultaneously addressing both waste biomass and NP pollutants.

Distribution characteristics and microbial synergistic degradation potential of polyethylene and polypropylene in freshwater estuarine sediments

The microbial degradation of polyethylene (PE) and polypropylene (PP) resins in rivers and lakes has emerged as a crucial issue in the management of microplastics. This study revealed that as the flow rate decreased longitudinally, ammonia nitrogen (NH4+-N), heavy fraction of organic carbon (HFOC), and small-size microplastics (< 1 mm) gradually accumulated in the deep and downstream estuarine sediments. Based on their surface morphology and carbonyl index, these sediments were identified as the potential hot zone for PE/PP degradation. Within the identified hot zone, concentrations of PE/PP-degrading genes, enzymes, and bacteria were significantly elevated compared to other zones, exhibiting strong intercorrelations. Analysis of niche differences revealed that the accumulation of NH4+-N and HFOC in the hot zone facilitated the synergistic coexistence of key bacteria responsible for PE/PP degradation within biofilms. The findings of this study offer a novel insight and comprehensive understanding of the distribution characteristics and synergistic degradation potential of PE/PP in natural freshwater environments.

Amphiphilic Magnetic Particles Dispersed in Water and Oil for the Removal of Hydrophilic and Hydrophobic Microplastics

The study explores the synthesis and versatile properties of amphiphilic magnetic particles (AMPs) achieved through sequential coatings. Modulating the hydrophobic content in the synthesis process allows for the formation of hydrophilic, amphiphilic, and hydrophobic magnetic particles, with stable AMPs synthesis achieved at a ratio of hydrophilic to hydrophobic portions of approximately 71 to 29%. These AMPs exhibited outstanding dispersion in both oil and water within an oil/water mixture. Polyethylenimine in the AMP primarily enhances the removal of hydrophilic microparticles and facilitates dispersion in water. On the other hand, octadecylamine is specifically designed for the effective elimination of hydrophobic microparticles and their dispersion in oil. AMPs demonstrated effective removal capabilities for both hydrophilic and hydrophobic microparticles in water as well as hydrophobic microparticles in 100% oil. Our approach is also suited for eliminating hydrophobic microparticles dispersed in small quantities of oil floating on large bodies of water in real-world situations.

Eco-friendly hydrophobic ZIF-8/sodium alginate monolithic adsorbent: An efficient trap for microplastics in the aqueous environment

Microplastics (MPs), a newly emerging class of environmental contaminants, pose a severe threat to the entire ecosystem. The development of efficient and environmentally responsible adsorbents for removing the MPs is a particularly urgent research. Herein, a kind of monolithic ZIF-8 based adsorbents featuring stable hydrophobicity and micropore-mesopore-macropore hierarchical porous structure were fabricated by in situ growth of ZIF-8 nanoparticles on sodium alginate (SA) framework, and using polydimethylsiloxane (PDMS) as a hydrophobic agent. The monolithic nature of ZIF-8/SA allowed an easy solid-liquid separation process for adsorbents from water environment compared to powdered materials. The hierarchical porous structure ensures a remarkable MPs removal performance. The ZIF-8/SA showed high adsorption capacities of 594, 585, and 282 mg/g for polymethyl methacrylate (PMMA), poly (vinylidene difluoride) (PVDF), and polyvinyl chloride (PVC) respectively, and rapid adsorption kinetic progress within 120 min. The ZIF-8/SA adsorbents also exhibited excellent stability in the presence of interfering ions, acid/alkali, and humic acid, and displayed adsorption performance of > 70 % even in actual aquatic environment such as tap water, river water, and seawater. The results of characterizations showed that the synergistic effect of electrostatic interaction, hydrogen bonding, hydrophobic force, and van der Waals force was the main adsorption mechanism. The well-designed hydrophobic ZIF-8/SA monolithic materials would be promising to rapidly remove the MPs from the water environment.

Synthesis of recyclable and light-weight graphene oxide/chitosan/genipin sponges for the adsorption of diclofenac, triclosan, and microplastics

Emerging micropollutants, such as pharmaceuticals and microplastics (MPs), have become a pressing water environmental concern. The aim of this study is to synthesize chitosan sponges using graphene oxide (GO) and genipin (GP) for the removal of pharmaceuticals (diclofenac (DCF) and triclosan (TCS)) and MPs, verify their adsorption mechanisms, evaluate the effects of temperature, pH, and salinity on their adsorption capacities, and determine their reusability. The GO5/CS/GP sponge exhibited a macroporous nature (porosity = 95%, density = 32.6 mg/cm3). GO and cross-linker GP enhanced the adsorption of DCF, TCS, and polystyrene (PS) MPs onto the CS sponges. The adsorption of DCF, TCS, and PS MPs involved multiple steps: surface diffusion and pore diffusion of the sponge. The adsorption isotherms demonstrated that Langmuir model was the most fitted well model to explain adsorption of TCS (qm = 7.08 mg/g) and PS MPs (qm = 7.42 mg/g) on GO5/CS/GP sponge, while Freundlich model suited for DCF adsorption (qm = 48.58 mg/g). DCF adsorption was thermodynamically spontaneous and endothermic; however, the adsorption of TCS and PS MPs was exothermic (283-313 K). The optimal pH was 5.5-7 due to the surface charge of the GO5/CS/GP sponge (pHzpc = 5.76) and ionization of DCF, TCS, and PS MPs. As the salinity increased, DCF removal efficiency drastically decreased due to the weakening of electrostatic interactions; however, TCS removal efficiency remained stable because TCS adsorption was mainly caused by hydrophobic and π-π interactions rather than electrostatic interaction. The removal of PS MPs was enhanced by the electrostatic screening effects of high Na+ ions. PS nanoplastics (average size = 26 nm) were removed by the GO5/CS/GP sponge at a rate of 73.0%, which was better than that of PS MPs (41.5%). In addition, the GO5/CS/GP sponge could be recycled over five adsorption-desorption cycles.

Microplastic pollutants in water: A comprehensive review on their remediation by adsorption using various adsorbents

Microplastics (MPs), as emerging pollutants, have attracted the attention of environmentalists, statespersons, and the scientific community over the last few decades. To address the spread of MPs in the environment, it is imperative to develop various removal techniques and materials that are effective, scalable, and ecologically benign. However, to the best of our knowledge, no review has systematically examined the removal of MPs using adsorption or provided an in-depth discussion on various adsorbents. Adsorption is an inexpensive and effective technology for wastewater treatment. Recently, many researchers have conducted studies on MP remediation using diverse adsorbent materials, such as biochar, activated carbon, sponges, carbon nanotubes, metal-layered oxides, metal-organic frameworks (MOFs), and zeolites. Each adsorbent has advantages and disadvantages. To overcome their disadvantages, researchers have been designing and developing hybrid adsorbents for MP remediation. This review provides insights into these individual adsorbents and also discusses hybrid adsorbents for MP removal. Finally, the review elaborates on future possibilities and ways to enable more efficient, scalable, and environmentally friendly MP cleanup. Overall, this review bridges the gap between contemporary MP remediation using adsorption techniques and adsorbent development.

Interactions between MPs and PFASs in aquatic environments: A dual-character situation

Microplastics (MPs) and per- and polyfluoroalkyl substances (PFASs) have drawn great attention as emerging threats to aquatic ecosystems. Although the literature to study the MPs and PFASs alone has grown significantly, our knowledge of the overlap and interactions between the two contaminations is scarce due to the unawareness of it. Actually, numerous human activities can simultaneously release MPs and PFASs, and the co-sources of the two are common, meaning that they have a greater potential for interactions. The direct interaction lies in the PFASs adsorption by MPs in water with integrated mechanisms including electrostatic and hydrophobic interactions, plus many influence factors. In addition, the existence and transportation of MPs and PFASs in the aquatic environment have been identified. MPs and PFASs can be ingested by aquatic organisms and cause more serious combined toxicity than exposure alone. Finally, curbing strategies of MPs and PFASs are overviewed. Wastewater treatment plants (WWTPs) can be an effective place to remove MPs from wastewater, while they are also an important point source of MPs pollution in water bodies. Although adsorption has proven to be a successful curbing method for PFASs, more technological advancements are required for field application. It is expected that this review can help revealing the unheeded relationship and interaction between MPs and PFASs in aquatic environments, thus assisting the further investigations of both MPs and PFASs as a whole.

Microalgal-based industry vs. microplastic pollution: Current knowledge and future perspectives

Microalgae can play a crucial role in the environment due to their efficient capture of CO2 and their potential as a solution for a carbon-negative economy. Water quality is critical for the success and profitability of microalgal-based industries, and understanding their response to emergent pollutants, such as microplastics (MPs), is essential. Despite the published studies investigating the impact of MPs on microalgae, knowledge in this area remains limited. Most studies have mainly focused on microalgal growth, metabolite analysis, and photosynthetic activity, with significant discrepancies in what is known about the impact on biomass yield. Recent studies show that the yield of biomass production depends on the levels of water contamination by MPs, making it necessary to reduce the contamination levels in the water. However, present technologies for extracting and purifying water from MPs are limited, and further research and technological advancements are required. One promising solution is the use of bio-based polymer materials, such as bacterial cellulose, which offer biodegradability, cost-effectiveness, and environmentally friendly detoxifying properties. This review summarises the current knowledge on MPs pollution and its impact on the viability and proliferation of microalgae-based industries, highlights the need for further research, and discusses the potential of bio-solutions for MPs removal in microalgae-based industries.

Application of carbon-based adsorbents in the remediation of micro- and nanoplastics

Micro-nano plastics (MNPs) are emerging contaminants that can easily enter the food chain, posing risks to both the aquatic ecosystem and human health. Various physical, biological, and chemical methods have been explored to remove MNPs from water, and recently, adsorption technology has gained attention as an effective approach. Among the potential candidates, carbon-based adsorbent has emerged as a promising choice due to their low cost, eco-friendly nature, and sustainability. This paper summarizes recent advancements in MNP removal using carbon-based adsorbents, with a focus on the modification methods and adsorption mechanisms. Additionally, the factors influencing the adsorption performance and the methods for characterizing the adsorption mechanism are analyzed. Finally, the advantages and disadvantages of carbon-based adsorbents over other adsorbents are discussed, along with the current state of sustainable recycling and future research prospects.

Dialdehyde modified and cationic aerogel for efficient microplastics adsorption from environmental waters

Recent reports had shown that microplastics could be transferred to organisms through various channels, severely and adversely affecting organisms' health and their physiological functions. Therefore, there remained an urgency to adopt an effective and environmentally friendly method to extract microplastics from water. In this paper, a cationic-modified d-DCPG aerogel with a three-dimensional network structure was successfully prepared by a directional freeze-drying technology in which double-aldehyde-modified cellulose nanofiber (CNF) was used as the matrix, betaine chloride hydrazide (GT) provided modification, and polyvinyl alcohol (PVA) provided cross-linking function. Aerogels had an excellent adsorption capacity (145.05 mg/g) for microplastics in aqueous environment, and when the pH was from 10 to 4, it exhibited an excellent adsorption efficiency from 90.01 % to 97.61 %; an excellent adsorption efficiency after 8 cycles (>89 %); pseudo-second-order kinetics and Freundlich adsorption isotherm had a high fitting effects on the adsorption process and adsorption results, respectively. And ultraviolet analysis also verified the occurrence of adsorption behavior. These results showed that d-DCPG aerogels had an excellent application prospects in microplastics removal in river, lake, reservoir, and marine environments.

Effect of polyaniline dispersibility in chitin sponge matrix controlled by hydrophilicity on microplastics adsorption

Microplastics have become an emerging threat to global ecosystems, and their efficient removal faces with serious challenges. Herein, this study introduced different hydrophilic polyaniline (PANIs) into chitin matrix to fabricate Chitin-PANIs sponge (ChPANIs) and investigated the relationship between PANIs dispersibility in chitin sponge matrix controlled by its hydrophilicity and adsorption effects on MPs. With the increase of PANIs' hydrophilicity (WCA from 153.9° to 32.8°), the removal efficiency of sponges to MPs increased from 84.0 % to 91.7 %. More hydrophilic PANIs can provide more contact surfaces and adsorption sites, which enhanced the electrostatic interactions to MPs and obtained excellent adsorption properties. The adsorption of MPs on ChPANIs accorded with the pseudo-first-order adsorption, suggesting that physical adsorption plays a dominant role. The adsorption process also conformed to Freundlich model, which displayed the MPs adsorption on ChPANI-PA could be multi-layer. The adsorption strength of ChPANIs was 0.7552, suggesting that it was a strong adsorbent. The ChPANIs also exhibited good mechanical properties and reusability, which its MPs removal efficiency just decreased from 91.7 % to 86.9 % during the five cycles. These findings expand the understanding of the adsorption mechanism analysis of MPs on sponge materials, and exist guiding significance for the design of adsorbed materials.

Microplastics removal technologies from aqueous environments: a systematic review

Purpose

Pollution of the environment with all kinds of plastics has become a growing problem. The problem of microplastics is mainly due to the absorption of stable organic pollutants and metals into them, and as a result, their environmental toxicity increases. The main purpose of this study is to investigate the appropriate and efficient methods of removing microplastics from aqueous environments through a systematic review.

Methods

Present study designed according to PRISMA guidelines. Two independent researchers followed all process from search to final analysis, for the relevant studies using international databases of PubMed, Scopus and ISI/WOS (Web of Science), without time limit. The search strategy developed based on the main axis of "microplastics", "aqueous environments" and "removal". This research was carried out from 2017 until the March of 2022. All relevant observational, analytical studies, review articles, and a meta-analysis were included.

Results

Through a comprehensive systematic search we found 2974 papers, after running the proses of refining, 80 eligible papers included to the study. According to the results of the review, the methods of removing microplastics from aquatic environments were divided to physical (12), chemical (18), physicochemical (27), biological (12) and integrated (11) methods. In different removal methods, the most dominant group of studied microplastics belonged to the four groups of polyethylene (PE), polystyrene (PS), polypropylene (PP) and polyethylene tetra phthalate (PET). Average removal efficiency of microplastics in different processes in each method was as: physical method (73.76%), chemical method (74.38%), physicochemical method (80.44%), biological method (75.23%) and integrated method (88.63%). The highest removal efficiency occurred in the processes based on the integrated method and the lowest efficiency occurred in the physical method. In total, 80% of the studies were conducted on a laboratory scale, 18.75% on a full scale and 1.25% on a pilot scale.

Conclusion

According to the findings; different processes based on physical, chemical, physicochemical, biological and integrated methods are able to remove microplastics with high efficiency from aqueous environments and in order to reduce their hazardous effects on health and environment, these processes can be easily used.

Current and Expected Trends for the Marine Chitin/Chitosan and Collagen Value Chains

Chitin/chitosan and collagen are two of the most important bioactive compounds, with applications in the pharmaceutical, veterinary, nutraceutical, cosmetic, biomaterials, and other industries. When extracted from non-edible parts of fish and shellfish, by-catches, and invasive species, their use contributes to a more sustainable and circular economy. The present article reviews the scientific knowledge and publication trends along the marine chitin/chitosan and collagen value chains and assesses how researchers, industry players, and end-users can bridge the gap between scientific understanding and industrial applications. Overall, research on chitin/chitosan remains focused on the compound itself rather than its market applications. Still, chitin/chitosan use is expected to increase in food and biomedical applications, while that of collagen is expected to increase in biomedical, cosmetic, pharmaceutical, and nutritional applications. Sustainable practices, such as the reuse of waste materials, contribute to strengthen both value chains; the identified weaknesses include the lack of studies considering market trends, social sustainability, and profitability, as well as insufficient examination of intellectual property rights. Government regulations, market demand, consumer preferences, technological advancements, environmental challenges, and legal frameworks play significant roles in shaping both value chains. Addressing these factors is crucial for seizing opportunities, fostering sustainability, complying with regulations, and maintaining competitiveness in these constantly evolving value chains.

Theoretical and experimental investigation on rapid and efficient adsorption characteristics of microplastics by magnetic sponge carbon

Microplastic pollution control has always been a thorny problem all over the world. Magnetic porous carbon materials have shown a good development prospect in microplastic adsorption due to their excellent adsorption performance and easy magnetic separation from water. However, the adsorption capacity and rate of magnetic porous carbon on microplastics are still not high, and the adsorption mechanism is not fully revealed, which hinders its further development. In this study, magnetic sponge carbon was prepared using glucosamine hydrochloride as the carbon source, melamine as the foaming agent, iron nitrate and cobalt nitrate as the magnetizing agents. Among them, Fe-doped magnetic sponge carbon (FeMSC) exhibited excellent adsorption performance for microplastics due to its sponge-like morphology (fluffy), strong magnetic properties (42 emu/g) and high Fe-loading (8.37 Atomic%). FeMSC could adsorb to saturation within 10 min, and the adsorption capacity of polystyrene (PS) reached as high as 369.07 mg/g in 200 mg/L microplastic solution, which was almost the fastest adsorption rate and highest adsorption capacity reported so far in the same condition. The performance of the material against external interference was also tested. FeMSC performed well in a wide pH range and different water quality, except in the strong alkaline condition. This is because the surface of microplastics and adsorbents will have many negative charges under strong alkalinity, significantly weakening the adsorption. Furthermore, theoretical calculations were innovatively used to reveal the adsorption mechanism at the molecular level. It was found that Fe-doping could form chemisorption between PS and the adsorbent, thereby significantly increasing the adsorption energy between the adsorbent and PS. The magnetic sponge carbon prepared in this study has excellent adsorption performance for microplastics and can be easily separated from water, which is a promising microplastic adsorbent.

A study on managing plastic waste to tackle the worldwide plastic contamination and environmental remediation

Over the past 50 years, the emergence of plastic waste as one of the most urgent environmental problems in the world has given rise to several proposals to address the rising levels of contaminants associated with plastic debris. Worldwide plastic production has increased significantly over the last 70 years, reaching a record high of 359 million tonnes in 2020. China is currently the world's largest plastic producer, with a share of 17.5%. Of the total marine waste, microplastics account for 75%, while land-based pollution accounts for responsible for 80-90%, and ocean-based pollution 10-20% only in overall pollution problems. Even at small dosages (10 μg/mL), microplastics have been found to cause toxic effects on human and animal health. This review examines the sources of microplastic contamination, the prevalent reaches of microplastics, their impacts, and the remediation methods for microplastic contamination. This review explains the relationship between the community composition and the presence of microplastic particulate matter in aquatic ecosystems. The interaction between microplastics and emerging pollutants, including heavy metals, has been linked to enhanced toxicity. The review article provided a comprehensive overview of microplastic, including its fate, environmental toxicity, and possible remediation strategies. The results of our study are of great value as they illustrate a current perspective and provide an in-depth analysis of the current status of microplastics in development, their test requirements, and remediation technologies suitable for various environments.

Control strategies for microplastic pollution in groundwater

Groundwater is the primary source of water that occurs below the earth's surface. However, the advancement in technology and the increasing population, which lead to the discharge of contaminants such as microplastics (MPs), have an adverse impact on the quality of groundwater. MPs are ubiquitous pollutants that are widely found throughout the world. The maximum abundance of MPs is 4 items/L and 15.2 items/L in groundwater at the specific location of China and USA. Various factors can affect the migration of MPs from soil to groundwater. The occurrence of MPs in water causes serious health issues. Therefore, taking appropriate strategies to control MP contamination in groundwater is urgent and important. This review summarizes the current literature on the migration process of MPs from soil to groundwater along with possible methods for the remediation of MP-polluted groundwater. The main objective of the review is to summarize the technical parameters, process, mechanism, and characteristics of various remediation methods and to analyze strategies for controlling MP pollution in groundwater, providing a reference for future research. Possible control strategies for MP pollution in groundwater include two aspects: i) prevention of MPs from entering groundwater; ii) remediation of polluted groundwater with MPs (ectopic remediation and in-situ remediation). Formulating legislative measures, strengthening public awareness and producing more environment-friendly alternatives can be helpful to reduce the production of MPs from the source. Manage plastic waste reasonably is also a good strategy and the most important part of the management is recycling. The shortcomings of the current study and the direction of future research are also highlighted in the review.

Ultralight sponge made from sodium alginate with processability and stability for efficient removal of microplastics

Due to natural agents and human activities, large quantities of microplastics enter the marine environment. As an emerging pollutant, MPs have attracted worldwide attention and become a great challenge in recent years. Sodium alginate is a kind of natural polysaccharide with non-toxic, stability, and low cost. In this study, sodium alginate sponge was prepared by secondary freeze-drying technology. Alginate sponge contains a large number of hydrophilic groups; thus, alginate sponge has super water-absorbed (the water absorption rate range from 1193-5232%). Meanwhile, the alginate sponge has high porosity of 81.93% and excellent mechanical properties. The removal efficiency of 100 mg·L-1 microplastics by alginate sponge reached up to 92.3%. The 1 mg·L-1 and 10 mg·L-1 microplastics can be completely absorbed in 27 h and 60 h, respectively. The adsorption mechanism of microplastics adsorbed onto alginate sponge included intra-particle diffusion, hydrogen bonds interactions, and π-π interactions. In addition, the adsorption of MPs loaded Cu2+/Na+ by sponge in complex aqueous environments is still significant. This study expands the development prospect of sodium alginate sponge materials in the field of water treatment and provides a new green approach for the removal of microplastics.

Engineering green MOF-based superhydrophobic sponge for efficiently synchronous removal of microplastics and pesticides from high-salinity water

Microplastics (MPs) and pesticides are becoming an intractable environmental issue due to their wide spreading and non-degradable nature, posing serious threat to ecosystem and human health. To settle such dilemma, this work reasonably designed a superhydrophobic MOF-based coated sponge (ODSOSS/TiO2/Ni-MOF/PDA@Sponge) through the combination of an environmentally friendly in-situ supersaturated coprecipitation and polysesiloxane modification method. Among them, (I) the introduction of polydopamine (PDA) not only improves the adhesion between coatings and sponge, but also enhances the growth of MOF structure through complexation. (II) The obtained Ni-MOF shows large-area microscale anthemy structure with multilayered flaky texture, forming heterogeneously hierarchical structure with the deposited TiO2 nanoparticles, which promotes photodegradation ability of TiO2 owing to great specific surface area of Ni-MOF. (III) The high specific large area Ni-MOF supplies sufficient action sites for linkage of PDA and polysesiloxane molecules with unique nanocage-like structure, thus further greatly increasing adsorption force for various pollutants. (IV) The superhydrophobicity protect the porous channels of MOF from contamination of various absorbed pollutants, while TiO2 nanoparticles effectively photodegrade the absorbed organic pollutants, endowing the sponge superior recyclability. The superhydrophobic sponge selectively rapidly and synchronously adsorbs various MPs (maintained almost 100% after 60 cycles) and pesticides (adsorption rates 71.6%-95.1%) from high-salinity water. The large-area sponge (9 cm × 6 cm × 1 cm) simultaneously removes almost 100% MPs (40 mg/L), Sudan Ⅲ (10 mg/L), kerosene (30 mL/L), and four pesticides (10 mg/L) within 1 min. Particularly, four pesticides are quickly photocatalytic degraded by the coated sponge. The free radical capture trials show that hydroxyl radicals (·OH) are the main active species of pesticide degradation. Furthermore, we reveal the negative centers where pesticide molecules are most vulnerable to ·OH attack, on basis of the charge distribution and molecular electrostatic potential (MEP) analysis. The adsorption mechanisms are carefully clarified through theoretical calculation and experimental data. This work not only provide an effective superhydrophobic candidate for MPs and pesticides removal in a broad applicable scope (especially in high-salinity wastewater), but also opens a new strategy for environmental remediation.

Microplastics in water: types, detection, and removal strategies

Microplastics are one of the most concerning groups of contaminants that pollute most of the surroundings of the Earth. The abundance of plastic materials available in the environment moved the scientific community in defining a new historical era known as Plasticene. Regardless of their minuscule size, microplastics have posed severe threats to the life forms like animals, plants, and other species present in the ecosystem. Ingestion of microplastics could lead to harmful health effects like teratogenic and mutagenic abnormalities. The source of microplastics could be either primary or secondary in which the components of microplastics are directly released into the atmosphere and the breakdown of larger units to generate the smaller molecules. Though numerous physical and chemical techniques are reported for the removal of microplastics, their increased cost prevents the large-scale applicability of the process. Coagulation, flocculation, sedimentation, and ultrafiltration are some of the methods used for the removal of microplastics. Certain species of microalgae are known to remove microplastics by their inherent nature. One of the biological treatment strategies for microplastic removal is the activated sludge strategy that is used for the separation of microplastic. The overall microplastic removal efficiency is significantly high compared to conventional techniques. Thus, the reported biological avenues like the bio-flocculant for microplastic removal are discussed in this review article.

The potential risks posed by micro-nanoplastics to the safety of disinfected drinking water

Micro-nanoplastics (M-NPs) have become an emerging critical issue in the environment because they migrate easily, can bioaccumulate with toxic effects, and are difficult to degrade. Unfortunately, the current technologies for removing or degrading M-NPs in drinking water are insufficient to eliminate them completely, and residual M-NPs in drinking water may pose a threat to human health by impairing human immunity and metabolism. In addition to their intrinsic toxic effects, M-NPs may be even more harmful after drinking water disinfection than before disinfection. Herein, this paper comprehensively summarizes the negative impacts of several commonly used disinfection processes (ozone, chlorine, and UV) on M-NPs. Moreover, the potential leaching of dissolved organics from M-NPs and the production of disinfection byproducts during the disinfection process are discussed in detail. Moreover, due to the diversity and complexity of M-NPs, their adverse effects may exceed those of conventional organics (e.g., antibiotics, pharmaceuticals, and algae) after the disinfection process. Finally, we propose enhanced conventional drinking water treatment processes (e.g., enhanced coagulation, air flotation, advanced adsorbents, and membrane technologies), detection of residual M-NPs, and biotoxicological assessment as promising and ecofriendly candidates to efficiently remove M-NPs and avoid the release of secondary hazards.

Microplastics as an emerging menace to environment: Insights into their uptake, prevalence, fate, and sustainable solutions

The inflated demand for plastic products has led to tremendous rise in plastic debris in different environmental matrices, thereby resulting in plastic pollution. This affects plants, animals, and even humans, as microplastics can enter the food chain and cause several health implications. Microplastics are the small plastic particles (size below 5 mm) that are largely debated nowadays owing to their environmental risk assessment. Their potential to interact with other toxic contaminants, their tendency to be ingested or taken up by living organisms and their longevity is a serious threat to our environment. However, despite wealth of recent information, still there is a gap, particularly in eco-toxicology studies, fate, prevalence and feasible solutions to cope up with the menace of microplastics pollution. This review unravels the environmental fate and behaviour of microplastics as well as their global distribution in the marine and terrestrial environment. Furthermore, we aim to contribute to the international debate on the microplastics global paradigm. We briefly suggest sustainable solutions and recommendations to achieve future research goals on microplastics. Our review reveals some of the newest biological (green algae and modified sponges) and physical (nano-particles and membrane treatment) remediation solutions to eradicate microplastics from different types of environment. This review presents a critical evaluation of the state of knowledge of micro-plastics and suggested some recommendations which can help in identifying some important key questions for future research.

A Janus branch filter for washing machines: Simultaneous removal of microplastics and surfactants

Emerging pollutants, such as microplastics (MPs), are becoming a significant issue worldwide. The highest percentage of MPs released into the environment occurs through daily laundry. The average weight of dreg obtained from 5 kg of laundry was 1.26 g/kg. According to energy dispersive X-ray (EDX) and thermogravimetric analysis (TGA) analyses, the dreg consisted of MPs (78.3-89 wt%, organic elements: C/O) and alien materials (11-21.7 wt%, inorganic elements: Al/Fe/Ca, etc.). Thus, to reproduce the real environment, alien materials (Fe₃O₄ and CaCO₃) were added to various types of model MPs in the presence and absence of sodium dodecyl benzenesulfonate (SDBS) to test MP removal. Hydrophobic and hydrophilic MPs were generated upon laundering, accounting for 55-59% and 41-45% of MPs, respectively. We provide a novel approach to design a laundry filter system for the simultaneous removal of SDBS and hydrophilic/hydrophobic MPs.

Microplastic remediation technologies in water and wastewater treatment processes: Current status and future perspectives

Microplastics (MPs) are a type of contaminants produced during the use and disposal of plastic products, which are ubiquitous in our lives. With the high specific surface area and strong hydrophobicity, MPs can adsorb various hazardous microorganisms and chemical contaminants from the environment, causing irreversible damage to our humans. It is reported that the MPs have been detected in infant feces and human blood. Therefore, the presence of MPs has posed a significant threat to human health. It is critically essential to develop efficient, scalable and environmentally-friendly methods to remove MPs. Herein, recent advances in the MPs remediation technologies in water and wastewater treatment processes are overviewed. Several approaches, including membrane filtration, adsorption, chemically induced coagulation-flocculation-sedimentation, bioremediation, and advanced oxidation processes are systematically documented. The characteristics, mechanisms, advantages, and disadvantages of these methods are well discussed and highlighted. Finally, the current challenges and future trends of these methods are proposed, with the aim of facilitating the remediation of MPs in water and wastewater treatment processes in a more efficient, scalable, and environmentally-friendly way.

Recent developments in microplastic contaminated water treatment: Progress and prospects of carbon-based two-dimensional materials for membranes separation

Micro (nano)plastics pollution is a noxious menace not only for mankind but also for marine life, as removing microplastics (MPs) is challenging due to their physiochemical properties, composition, and response toward salinity and pH. This review provides a detailed assessment of the MPs pollution in different water types, environmental implications, and corresponding treatment strategies. With the advancement in nanotechnology, mitigation strategies for aqueous pollution are seen, especially due to the fabrication of nanosheets/membranes mostly utilized as a filtration process. Two-dimensional (2D) materials are increasingly used for membranes due to their diverse structure, affinity, cost-effectiveness, and, most importantly, removal efficiency. The popular 2D materials used for membrane-based organic and inorganic pollutants from water mainly include graphene and MXenes however their effectiveness for MPs removal is still in its infancy. Albeit, the available literature asserts a 70- 99% success rate in micro/nano plastics removal achieved through membranes fabricated via graphene oxide (GO), reduced graphene oxide (rGO) and MXene membranes. This review examined existing membrane separation strategies for MPs removal, focusing on the structural properties of 2D materials, composite, and how they adsorb pollutants and underlying physicochemical mechanisms. Since MPs and other contaminants commonly coexist in the natural environment, a brief examination of the response of 2D membranes to MPs removal was also conducted. In addition, the influencing factors regulate MPs removal performance of membranes by impacting their two main operating routes (filtration and adsorption). Finally, significant limitations, research gaps, and future prospects of 2D material-based membranes for effectively removing MPs are also proposed. The conclusion is that the success of 2D material is strongly linked to the types, size of MPs, and characteristics of aqueous media. Future perspectives talk about the problems that need to be solved to get 2D material-based membranes out of the lab and onto the market.

Innovations in the Development of Promising Adsorbents for the Remediation of Microplastics and Nanoplastics - A Critical Review

Microplastics and nanoplastics are being assumed as emerging toxic pollutants owing to their unique persistent physicochemical attributes, chemical stability, and nonbiodegradable nature. Owing to their possible toxicological impacts (not only on aquatic biota but also on humans), scientific communities are developing innovative technologies to remove microplastics and nanoplastics from polluted waters. Various technologies, including adsorption, coagulation, photocatalysis, bioremediation, and filtration, have been developed and employed to eliminate microplastics and nanoplastics. Recently, adsorption technology has been getting great interest in capturing microplastics and nanoplastics and achieving excellent removal performance. Therefore, this review is designed to discuss recent innovations in developing promising adsorbents for the remediation of microplastics and nanoplastics from wastewater and natural water. The developed adsorbents have been classified into four main classes: sponge/aerogel-based, metal-based, biochar-based, and other developed adsorbents, and their performance efficiencies have been critically examined. Further, the influence of various pertinent factors, including adsorbents' characteristics, microplastics/nanoplastics' characteristics, solution pH, reaction temperature, natural organic matter, and co-existing/interfering ions on the removal performance of advanced adsorbents, have been critically assessed. Importantly, the particle application of the developed adsorbents in removing microplastics and nanoplastics from natural water has been elucidated. In addition, barriers to market penetration of the developed adsorbents are briefly discussed to help experts transfer adsorption-based technology from laboratory-scale to commercial applications. Finally, the current knowledge gaps and future recommendations are highlighted to assist scientific communal for improving adsorption-based technologies to battle against microplastics and nanoplastics pollution.

The role of available nitrogen in the adsorption of polystyrene nanoplastics on magnetic materials

Several studies have been conducted on nanoplastics (NPs). However, few studies have investigated the complexity of the interactions between NPs and other aqueous pollutants in multi-solute media. In this study, the adsorption of polystyrene nanoplastics (PSNPs) on magnetic materials (MS) in the presence of available nitrogen (AN) was studied. The results demonstrated that the adsorbed amount of PSNPs increased in the presence of ammonium nitrogen (NH₄⁺-N), whereas no significant difference was detected on the adsorbed amount of PSNPs using nitrate nitrogen (NO₃^--N) as a cosolute. The increase in the adsorbed amount of PSNPs was attributed to the formation of an MS-PSNPs-NH₄⁺-N complex. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and zeta potential analyses indicated that the PSNPs with NH₄⁺-N as a cosolute can be bound on the MS surfaces. Moreover, the change in the PSNPs amount adsorbed by MS depends on the valence state, electronegativity of the coexisting ions, and the surface properties and functional groups of PSNPs. Additionally, the ionic strength, dissolved organic matter, solution pH, metal cations and the subsequent release of MS-coated PSNPs and NH₄⁺-N changed considerably in different aquatic systems and artificial nitrating fluids. Among different natural aquatic systems, the PSNPs adsorption on MS was excellent in lake water. The results indicate high potential for the attachment of PSNPs to MS in the presence of AN and further deepen the understanding of removing NPs using magnetic materials in aqueous systems with various coexisting contaminants.

Removal of nanoplastics from aqueous solution by aggregation using reusable magnetic biochar modified with cetyltrimethylammonium bromide

Nanoplastics (NPs) pollution has become an emerging threat to the aquatic environment and its organisms. The removal of NPs from contaminated water is a global challenge. In this study, an efficient and reusable composite was prepared from cetyltrimethylammonium bromide (CTAB) modified magnetic biochar. The performances of CTAB modified magnetic biochar (CMB) to remove polystyrene (PS) and carboxylate-modified polystyrene (CPS) nanoparticles from water were systematically evaluated. The results showed that the PS and CPS removal performance of magnetic biochar was improved by CTAB modification. These increases were assigned to the increase in the surface hydrophobicity of CMB. Due to the strong electrostatic repulsion between the nanoparticles, PS and CPS maintained high stability in alkaline conditions, resulting in a significant decrease in removal efficiency. The removal efficiency was decreased to 67.4% for PS and to 40.7% for CPS at pH 11. The inhibition effects of NaCl on the PS and CPS removal efficiencies were decreased gradually with the increase of NaCl concentration. Among the anions studied, H₂PO₄^- had the biggest impact on the removal performance of CMB. Besides, CMB could be used to remove PS and CPS in real surface water, and the removal efficiencies of PS and CPS were 95.3% and 97.8%, respectively. Particularly, the removal efficiencies of PS and CPS were 90.2% for PS and 94.8% for CPS when CMB was recycled five times. According to the characterization results of XRD, TGA, SEM, FTIR and XPS, PS and CPS nanoparticles were removed by CMB from water mainly through aggregation instead of adsorption. The efficient removal of PS and CPS by CMB via aggregation process offers new insight into the removal of NPs from aquatic environment.

Enhanced removal of aged and differently functionalized polystyrene nanoplastics using ball-milled magnetic pinewood biochars

In this study, simple and environmentally friendly magnetic biochars were successfully prepared by ball-milling biochar with Fe₃O₄ nanoparticles to remove NPs from water. The magnetic biochars synthesized at various pyrolysis temperatures of 300 °C (MBC300), 500 °C (MBC500), and 700 °C (MBC700) were used to eliminate the unmodified (PS), aged under UV radiation (UVPS), amine-modified (PS-NH₂) and carboxylate-modified (PS-COOH) polystyrene NPs of 100 nm in size. Results showed that the removal efficiency of MBC300, MBC500, and MBC700 for PS were 43.67, 82.73 and 57.02%, which were 3.01, 5.76, and 3.10 times greater than that of corresponding pristine biochars at the same temperatures, respectively, and the strongest removal efficiency of MBC500 was 95.2% since it has the largest specific surface area and abundant oxygen-containing functional groups. The surface properties of the NPs affected their removal, and the PS-NH₂ had the highest removal rate using magnetic biochars. Compared to pristine biochars, the magnetic biochars displayed faster adsorption kinetics. The Langmuir maximum adsorption capacity of magnetic biochars for NPs were 107.7181-229.5772 mg/g, much greater than those of the pristine biochars (55.4602-80.3096 mg/g). Mechanism analysis revealed that the hydrophobicity, electrostatic attraction, H-bonding formation and π-π conjunction between the NPs and MBCs contributed to the adsorption process. This work highlights the promising potential of ball milling to be used as a simple technique for the preparation of magnetic biochar to remove NPs, especially NPs with various surface groups.

Microplastics removal and characteristics of a typical multi-combination and multi-stage constructed wetlands wastewater treatment plant in Changsha, China

Wastewater treatment plants (WWTPs) are an important source of microplastics (MPs) entering the aquatic environment. As environmental awareness increases, WWTPs are gradually using constructed wetlands (CWs) in the depth treatment stage. There were few studies related to MPs removal efficiency of CWs, especially in multi-stage and multi-combinations CWs. Therefore, we studied MPs characteristics and removal in a typical CWs WWTP in Changsha, comparing the MPs removal efficiencies of different processes in a WWTP, focusing on the MPs abundance variation in different stages CWs. Result showed that the MPs removal efficiency of Phase Ⅰ was 87.72% and that of Phase II was 80.65%. Approximate estimates showed that the daily discharge of MPs reached 7.20 * 10⁸ items. The MPs removal efficiency of vertical flow CWs was 25.71%. The MPs removal efficiencies of secondary and tertiary horizontal subsurface flow CWs (HSSFCWs) were 32.00% and 21.43%. The MPs removal efficiencies of secondary and tertiary surface flow CWs were 23.53% and 12.50%. The MPs removal efficiencies of three bio-ponds were -23.08%, -12.90%, and -27.27%. Combined system of bio-pond + CWs reduced the MPs removal efficiency. The most dominant shape of MPs in wastewater was fibers. The most common MPs were polyethylene and polystyrene. The primary treatment in the Changsha WWTP had the highest MPs removal efficiency. Results of this investigation showed the multi-combination and multi-stage CWs WWTP can remove most of MPs in influent, which greatly reduced the amount of MPs discharged into the aquatic environment through WWTP and provided data for analyzing the distribution of MPs in the aquatic environment.

Removing microplastics from aquatic environments: A critical review

As one of the typical emerging contaminants, microplastics exist widely in the environment because of their small size and recalcitrance, which has caused various ecological problems. This paper summarizes current adsorption and removal technologies of microplastics in typical aquatic environments, including natural freshwater, marine, drinking water treatment plants (DWTPs), and wastewater treatment plants (WWTPs), and includes abiotic and biotic degradation technologies as one of the removal technologies. Recently, numerous studies have shown that enrichment technologies have been widely used to remove microplastics in natural freshwater environments, DWTPs, and WWTPs. Efficient removal of microplastics via WWTPs is critical to reduce the release to the natural environment as a key connection point to prevent the transfer of microplastics from society to natural water systems. Photocatalytic technology has outstanding pre-degradation effects on microplastics, and the isolated microbial strains or enriched communities can degrade up to 50% or more of pre-processed microplastics. Thus, more research focusing on microplastic degradation could be carried out by combining physical and chemical pretreatment with subsequent microbial biodegradation. In addition, the current recovery technologies of microplastics are introduced in this review. This is incredibly challenging because of the small size and dispersibility of microplastics, and the related technologies still need further development. This paper will provide theoretical support and advice for preventing and controlling the ecological risks mediated by microplastics in the aquatic environment and share recommendations for future research on the removal and recovery of microplastics in various aquatic environments, including natural aquatic environments, DWTPs, and WWTPs.

Chitin and chitin-based biomaterials: A review of advances in processing and food applications

Chitin is the most abundant natural amino polysaccharide, showing various practical applications owing to its functional properties. However, there are barriers in the development due to the difficulty of chitin extraction and purification, regarding its high crystallinity and low solubility. In recent years, some novel technologies such as microbial fermentation, ionic liquid, electrochemical extraction have emerged for the green extraction of chitin from new sources. Furthermore, nanotechnology, dissolution systems and chemical modification were applied to develop a variety of chitin-based biomaterials. Remarkably, chitin was used in delivering active ingredients and developing functional foods for weight loss, lipid reduction, gastrointestinal health, and anti-aging. Moreover, the application of chitin-based materials was expanded into medicine, energy and the environment. This review outlined the emerging extraction methods and processing routes of different chitin sources and advances in applying chitin-based materials. We aimed to provide some direction for the multi-disciplinary production and application of chitin.

Current status of microplastics and nanoplastics removal methods: Summary, comparison and prospect

In modern society, plastics also play an indispensable role in people's lives due to their various excellent properties. However, when these plastic products are discarded after being used, after being subjected to external influences, they will continue to be worn, damaged and degraded into micro- and nano-scale plastics, which are microplastics and nanoplastics (M/NPs). Although people's attention has been paid to M/NPs at present, the focus is still mainly on the detection and hazard of M/NPs, and how to remove M/NPs is relatively less popular. This review was written in order to draw the attention of more researchers to remove M/NPs. This review first briefly introduces the research background of M/NPs, and also shows the main analytical methods currently used for qualitative and quantitative M/NPs. Then, most of the current literature on the removal of M/NPs was collected, and they were classified, summarized, and introduced according to the classification of physical, physicochemical, and biological methods. The advantages and disadvantages of various methods are summarized, and they are also compared, which can help more researchers choose the appropriate method for research. In addition, the application scenarios of these methods are briefly introduced. Finally, some future research directions are proposed for the current research status of M/NPs removal. It is hoped that this will further promote the development on the method of removing M/NPs.

Sustainable, High-Performance, and Biodegradable Plastics Made from Chitin

A high-performance biodegradable plastic was made from a chitin KOH/urea solution. The solution was transferred into a hydrogel by cross-linking using epichlorohydrin and ethanol immersion, and a chitin bioplastic was finally prepared by drying in a mold at 40 °C. The solution concentration positively impacts viscosity, crystallinity, and smoothness. A 4% chitin bioplastic exhibits high barrier properties, flame retardancy, high-temperature resistance, mechanical properties (tensile strength up to 107.1 MPa), and soil degradation properties. The chitin bioplastic can be completely degraded by microorganisms in 7 weeks. In addition, biosafety tests suggest that chitin is safe for cells and crops (wheat and mung beans). The chitin bioplastic was further applied to containers, straws, cups, and photoprotection, and it was found that the water resistance and transparency were comparable to those of commercial polypropylene plastics. Due to the excellent performance, safety, and sustainability of the chitin bioplastic, it is expected to become a good substitute for conventional fossil fuel-based plastics.

Engineering 3D graphene-like carbon-assembled layered double oxide for efficient microplastic removal in a wide pH range

Microplastics (MPs) elimination is becoming an intractable environmental issue due to their nonbiodegradable nature and wide spreading，especially in the case of wastewater containing acid or alkaline effluent. To target the dilemma, this work rationally engineered a robust three-dimensional graphene-like carbon assembled layered double oxide material (defined as G@LDO) from hierarchical organic LDH (i.e., 3D OLDH) via a "precursor-calcination" strategy. In virtue of the mutually protection effect of graphene-like carbon (G) and LDO, the engineered G@LDO featured the preeminent acid and base resistance for polystyrene (PS, as representative of MPs) removal. Especially and importantly, the removal efficiency of PS was ≥ 80% at pH= 3-11, even nearly 60% PS was removed at pH= 1 and 13. The maximum adsorption ability of G@LDO for PS was estimated to be 209.39 mg/g by a Langmuir isotherm model, much superior to that of pure G, LDO, and 2D G@LDO. Furthermore, the removal pathway was analyzed by kinetic together with thermodynamic study, revealing that the PS removal on G@LDO was an exothermic reaction controlled by chemisorption. By systematical characterization and DFT calculation, the removal mechanism of PS was revealed to be hydrogen bond and complexation associated with LDH recovered from LDO and π-π conjunction from G. Notably, the existence of sulfure (S) in the carbon network was also identified as significant component in PS removal via p-π interaction. Overall, this work not only provides a effective candidate for microplastics removal in a wide applicable scope (especially acid/alkaline effluent), shedding light on environmental remediation, but also opens a new anvenue for the disposal of LDHs adsorbed organic in a high value-added manner.

Mechanically durable anti-bacteria non-fluorinated superhydrophobic sponge for highly efficient and fast microplastic and oil removal

Microplastics (MPs) pollution evolves into a global environmental problem to be solved urgently. Although many studies are exploring ways to remove MPs from water environment, most of them are lack of selectivity and low efficiency. Herein, considering the fascinating absorption selectivity of superwetting materials, a robust magnetic-responsive superhydrophobic and superoleophilic sponge was firstly used to quickly eliminate MPs from water with very high efficiency. The functional sponge was fabricated by a non-fluorinated coating technique that consisted of polydimethylsiloxane (PDMS) grafted Fe₃O₄ particle, PDMS grafted halloysite nanotubes, and PDMS binder. The coated sponge achieved excellent mechanically durable and chemically stable superhydrophobicity that resisted a series of severe treatments. It was unquestionable to show very fast oil absorption. What's more, it especially showed very high adsorption capacity (24.3-48.2 mg/g) and could quickly adsorb almost 100% MPs (polypropylene, polyvinyl chloride, and polyethylene) from aqueous suspensions. Moreover, the removal rates remained almost 100% for these MPs after 50 cycles. Besides, the coated sponge had excellent salt tolerance and antibacterial activity to Escherichia coli (E. coli) (99.91%) and Staphylococcus aureus (S. aureus) (90.46%). The adsorption mechanism of the coating was discussed from the perspectives of molecular structure, electronic effect, steric hindrance, and size-scale effect. The absorption driving force mainly derived from the intra-particle diffusion under capillary attraction, whilst slight electrostatic interaction, hydrogen bond interaction, and σ-p (or p-p) conjugation between PDMS and MPs. This functional sponge was destined to be a new strategy in the removal of MPs and other solid pollutants, especially in the high-salinity and rich-microorganism water environment.

Nanomaterials for microplastic remediation from aquatic environment: Why nano matters?

The contamination of microplastics in aquatic environment is regarded as a serious threat to ecosystem especially to aquatic environment. Microplastic pollution associated problems including their bioaccumulation and ecological risks have become a major concern of the public and scientific community. The removal of microplastics from their discharge points is an effective way to mitigate the adverse effects of microplastic pollution, hence has been the central of the research in this realm. Presently, most of the commonly used water or wastewater treatment technologies are capable of removing microplastic to certain extent, although they are not intentionally installed for this reason. Nevertheless, recognizing the adverse effects posed by microplastic pollution, more efforts are still desired to enhance the current microplastic removal technologies. With their structural multifunctionalities and flexibility, nanomaterials have been increasingly used for water and wastewater treatment to improve the treatment efficiency. Particularly, the unique features of nanomaterials have been harnessed in synthesizing high performance adsorbent and photocatalyst for microplastic removal from aqueous environment. This review looks into the potentials of nanomaterials in offering constructive solutions to resolve the bottlenecks and enhance the efficiencies of the existing materials used for microplastic removal. The current efforts and research direction of which studies can dedicate to improve microplastic removal from water environment with the augmentation of nanomaterial-enabled strategies are discussed. The progresses made to date have witnessed the benefits of harnessing the structural and dimensional advantages of nanomaterials to enhance the efficiency of existing microplastic treatment processes to achieve a more sustainable microplastic cleanup.

Environmentally azithromycin pharmaceutical wastewater management and synergetic biocompatible approaches of loaded azithromycin@hematite nanoparticles

Pharmaceutical wastewater contamination via azithromycin antibiotic and the continuous emergence of some strains of bacteria, cancer, and the Covid-19 virus. Azithromycin wastewater treatment using the biosynthesized Hematite nanoparticles (α-HNPs) and the biocompatible activities of the resulted nanosystem were reported. Biofabrication of α-HNPs using Echinacea purpurea liquid extract as a previously reported approach was implemented. An evaluation of the adsorption technique via the biofabricated α-HNPs for the removal of the Azr drug contaminant from the pharmaceutical wastewater was conducted. Adsorption isotherm, kinetics, and thermodynamic parameters of the Azr on the α-HNPs surface have been investigated as a batch mode of equilibrium experiments. Antibacterial, anticancer, and antiviral activities were conducted as Azr@α-HNPs. The optimum conditions for the adsorption study were conducted as solution pH = 10, 150 mg dose of α-HNPs, and Azr concentration 400 mg/L at 293 K. The most fitted isothermal model was described according to the Langmuir model at adsorption capacity 114.05 mg/g in a pseudo-second-order kinetic mechanistic at R² 0.9999. Thermodynamic study manifested that the adsorption behavior is a spontaneous endothermic chemisorption process. Subsequently, studying the biocompatible applications of the Azr@α-HNPs. Azr@α-HNPs antibacterial activity revealed a synergistic effect in the case of Gram-positive more than Gram-negative bacteria. IC₅₀ of Azr@α-HNPs cytotoxicity against MCF7, HepG2, and HCT116 cell lines was investigated and it was found to be 78.1, 81.7, and 93.4 µg/mL respectively. As the first investigation of the antiviral use of Azr@α-HNPs against SARS-CoV-2, it was achieved a safety therapeutic index equal to 25.4 revealing a promising antiviral activity. An admirable impact of the use of the biosynthesized α-HNPs and its removal nanosystem product Azr@α-HNPs was manifested and it may be used soon as a platform of the drug delivery nanosystem for the biomedical applications.

Coral-inspired environmental durability aerogels for micron-size plastic particles removal in the aquatic environment

Removing microplastics (MPs) from water has been a huge challenge due to their inherent features including small size and high stability. In this research, inspired by the active adsorption and passive adhesion mechanisms of corals to MPs, a new strategy to fabricate polydopamine enhanced magnetic chitosan (PDA-MCS) aerogels was developed with a target to match the surface properties of MPs, achieving high MPs removal efficiency. PDA-MCS aerogels were highly efficient in adsorbing polyethylene terephthalate (PET) microplastics in water at pH values of 6-9, with a removal efficiency of up to 91.6%. Even after three recycles, PDA-MCS aerogels still displayed comparatively high removal efficiency (83.4%). Kinetic and isothermal experiments showed that the adsorption process was the result of electrostatic interactions and physical adhesion between aerogels and microplastics. Moreover, PDA-MCS aerogels maintained high removal efficiency under simulated environmental conditions, and the removal efficiency of PET, polyethylene (PE) and polystyrene (PS) microplastics in waters reached 97.3%, 94.6%, and 92.3%, respectively. Therefore, high-efficiency environmentally durable aerogels adsorbent materials have the potential for the removal of MPs from the aquatic environment.