High-efficiency oxidation of fluoroquinolones by the synergistic activation of peroxymonosulfate via vacuum ultraviolet and ferrous iron

Efficient removal of moxifloxacin through PMS activation by CuFeS2/MXene

Due to the frequent detection and potential toxicity of moxifloxacin (MOX), its removal technology had attracted attention in recent years. In this research, CuFeS2/MXene was prepared and used to activate peroxymonosulfate (PMS) to remove MOX. The degradation efficiencies, kinetics, influences, and reaction mechanism of MOX by CuFeS2/MXene/PMS were investigated. The synergistic effect of CuFeS2 and MXene significantly enhanced PMS activation, producing SO4•-, HO•, and 1O2 as the main active species. By adding 0.12 g/L CuFeS2/MXene and 0.12 mM PMS, MOX removal efficiency reached 99.1% within 40 min, with a rate constant of 0.1073 min-1. The composite ratios of CuFeS2/MXene impacted PMS activation more significantly than catalyst dosages and PMS concentrations. Acidic conditions were favorable for the degradation of MOX, while HCO3-, HPO42-, Mn2+, and HA had the inhibitory effects. Twelve major products were detected by HPLC-MS, and DFT was used to illustrate possible degradation pathways of MOX, including the removal of nitrogen-containing heterocycle and transformations of quinolone moieties. Toxicity analysis showed that the developmental toxicity, mutagenicity, and acute toxicity of degradation products tended to decrease. CuFeS2/MXene could exhibit excellent reusability, maintaining an average MOX degradation efficiency of 90.8% in the 7-cycle experiments.

Microfluidic sensors for the detection of emerging contaminants in water: A review

In recent years, numerous emerging contaminants have been identified in surface water, groundwater, and drinking water. Developing novel sensing methods for detecting diverse emerging pollutants in water is urgently needed, as even at low concentrations, these pollutants can pose a serious threat to human health and environmental safety. Traditional testing methods are based on laboratory equipment, which is highly sensitive but complex to operate, costly, and not suitable for on-site monitoring. Microfluidic sensors offer several benefits, including rapid evaluation, minimal sample usage, accurate liquid manipulation, compact size, automation, and in-situ detection capabilities. They provide promising and efficient analytical tools for high-performance sensing platforms in monitoring emerging contaminants in water. In this paper, recent research advances in microfluidic sensors for the detection of emerging contaminants in water are reviewed. Initially, a concise overview is provided about the various substrate materials, corresponding microfabrication techniques, different driving forces, and commonly used detection techniques for microfluidic devices. Subsequently, a comprehensive analysis is conducted on microfluidic detection methods for endocrine-disrupting chemicals, pharmaceuticals and personal care products, microplastics, and perfluorinated compounds. Finally, the prospects and future challenges of microfluidic sensors in this field are discussed.

Vacuum-ultraviolet based advanced oxidation and reduction processes for water treatment

The use of vacuum-ultraviolet (VUV) photolysis in water treatment has been gaining significant interest due to its efficacy in degrading refractory organic contaminants and eliminating oxyanions. In recent years, the reactive species driving pollutant decomposition in VUV-based advanced oxidation and reduction processes (VUV-AOPs and VUV-ARPs) have been identified. This review aims to provide a concise overview of VUV photolysis and its advancements in water treatment. We begin with an introduction to VUV irradiation, followed by a summary of the primary reactive species in both VUV-AOPs and VUV-ARPs. We then explore the factors influencing VUV-photolysis in water treatment, including VUV irradiation dose, catalysts or activators, dissolved gases, water matrix components (e.g., DOM and inorganic anions), and solution pH. In VUV-AOPs, the predominant reactive species are hydroxyl radicals (˙OH), hydrogen peroxide (H2O2), and ozone (O3). Conversely, in VUV-ARPs, the main reactive species are the hydrated electron (eaq-) and hydrogen atom (˙H). It is worth noting that VUV-based advanced oxidation/reduction processes (VUV-AORPs) can transit between VUV-AOPs and VUV-ARPs based on the externally added chemicals and dissolved gases in the solution. Increase of the VUV irradiation dose and the concentration of catalysts/activators enhances the degradation of contaminants, whereas DOM and inorganic anions inhibit the reaction. The pH influences the redox potential of ˙OH, the speciation of contaminants and activators, and thus the overall performance of the VUV-AOPs. Conversely, an alkaline pH is favored in VUV-ARPs because eaq- predominates at higher pH.

Novel vacuum UV/ozone/peroxymonosulfate process for efficient degradation of levofloxacin: Performance evaluation and mechanism insight

Vacuum UV (VUV) irradiation has advantage in coupling oxidants for organics removal because VUV can dissociate water to produce reactive oxygen species (ROS) in situ and decompose oxidants rapidly. In this study, the synergistic activation of peroxymonosulfate (PMS) by VUV and ozone (O3) was explored via developing a novel integrated VUV/O3/PMS process, and the performance and mechanisms of VUV/O3/PMS for levofloxacin (LEV) degradation were investigated systematically. Results indicated that VUV/O3/PMS could effectively degrade LEV, and the degradation rate was 1.67-18.79 times of its sub-processes. Effects of PMS dosage, O3 dosage, solution pH, anions, and natural organic matter on LEV removal by VUV/O3/PMS were also studied. Besides, hydroxyl radical and sulfate radical were main ROS with contributions of 49.7% and 17.4%, respectively. Moreover, the degradation pathways of LEV in VUV/O3/PMS process were speculated based on density functional theory calculation and by-products detection. Furthermore, synergistic reaction mechanisms in VUV/O3/PMS process were proposed. The energy consumption of VUV/O3/PMS decreased by 22.6%- 88.1% compared to its sub-processes. Finally, the integrated VUV/O3/PMS process showed satisfactory results in removing LEV in actual waters, manifesting VUV/O3/PMS had great application potential and feasibility in removing organics in wastewater reuse.

Chemical-free vacuum ultraviolet irradiation as ultrafiltration membrane pretreatment technique: Performance, mechanisms and DBPs formation

Membrane fouling induced by natural organic matter (NOM) has seriously affected the further extensive application of ultrafiltration (UF). Herein, a simple, green and robust vacuum ultraviolet (VUV) technology was adopted as pretreatment before UF and ultraviolet (UV) technology was used for comparison. The results showed that control effect of VUV pretreatment on membrane fouling was better than that of UV pretreatment, as evidenced by the increase of normalized flux from 0.27 to 0.38 and 0.73 after 30 min UV or VUV pretreatment, respectively. This is related to the fact that VUV pretreatment exhibited stronger NOM degradation ability than UV pretreatment owing to the formation of HO•. The steady-state concentration of HO• was calculated as 3.04 × 10-13 M and the cumulative exposure of HO• reached 5.52 × 10-10 M s after 30 min of VUV irradiation. And the second-order rate constant between NOM and HO• was determined as 1.36 × 104 L mg-1 s-1. Furthermore, fluorescence EEM could be applied to predict membrane fouling induced by humic-enriched water. Standard blocking and cake filtration were major fouling mechanisms. Moreover, extension of UV pretreatment time increased the disinfection by-products (DBPs) formation, the DBPs concentration was enhanced from 322.36 to 1187.80 μg/L after 210 min pretreatment. However, VUV pretreatment for 150 min reduced DBPs content to 282.57 μg/L, and DBPs content continued to decrease with the extension of pretreatment time, revealing that VUV pretreatment achieved effective control of DBPs. The variation trend of cytotoxicity and health risk of DBPs was similar to that of DBPs concentration. In summary, VUV pretreatment exhibited excellent effect on membrane fouling alleviation, NOM degradation and DBPs control under a certain pretreatment time.

Degradation of Ciprofloxacin in Water by Magnetic-Graphene-Oxide-Activated Peroxymonosulfate

Antibiotics are extensively applied in the pharmaceutical industry, while posing a tremendous hazard to the ecosystem and human health. In this study, the degradation performance of ciprofloxacin (CIP), one of the typical contaminants of antibiotics, in an oxidation system of peroxymonosulfate (PMS) activated by magnetic graphene oxide (MGO) was investigated. The effects of the MGO dosage, PMS concentration and pH on the degradation of CIP were evaluated, and under the optimal treatment conditions, the CIP degradation rate was up to 96.5% with a TOC removal rate of 63.4%. A kinetic model of pseudo-secondary adsorption indicated that it involves an adsorption process with progressively intensified chemical reactions. Furthermore, the MGO exhibited excellent recyclability and stability, maintaining strong catalytic activity after three regenerative cycles, with a CIP removal rate of 87.0%. EPR and LC-MS experiments suggested that •OH and SO4-• generated in the MGO/PMS system served as the main reactants contributing to the decomposition of the CIP, whereby the CIP molecule was effectively destroyed to produce other organic intermediates. Results of this study indicate that organic pollutants in the aqueous environment can be effectively removed in the MGO/PMS system, in which MGO has excellent catalytic activity and stabilization for being recycled to avoid secondary pollution, with definite research value and application prospects in the field of water treatment.

The pH-sensitive transformation of birnessite and its effect on the fate of norfloxacin

Birnessite plays a crucial role in regulating the fate of contaminants in soil, which is affected by the crystal structure of birnessite. In this study, the transformation of triclinic birnessite to hexagonal birnessite was examined at various pH values, and their reactivity towards norfloxacin was investigated. The findings indicate that the conversion from triclinic birnessite to hexagonal birnessite occurs under pH conditions lower than 7. The lower of the solution pH where the birnessite formed, the higher the surface reactivity. Throughout the transformation process, the migration of Mn3+ and the increased interlayer protons generated more reactive oxygen species, which enhanced the surface reactivity towards norfloxacin. Specifically, at a conversion pH of 1, the norfloxacin removal rate significantly increases from 14% to 97% compared to triclinic birnessite. The mechanism of norfloxacin removal by triclinic and hexagonal birnessite is illustrated. These findings provide valuable insights into the dynamic transformation of birnessites in aqueous environments with varying pH values and their impact on norfloxacin removal.

Visible-light-driven peroxymonosulfate activation by robust TiO2-base nanoparticles for efficient removal of sulfamethoxazole

In this study, a novel bimetallic Co-Mo-TiO2 nanomaterial was fabricated through a simple two-step method, and applied as photocatalyst to activate peroxymonosulfate (PMS) with high efficiency for sulfamethoxazole (SMX) removal under visible light. Nearly 100% of SMX was degraded within 30 min in Vis/Co-Mo-TiO2/PMS system, and its kinetic reaction rate constant (0.099 min-1) was 24.8 times higher compare with the Vis/TiO2/PMS system (0.014 min-1). Moreover, the quenching experiments and the electronic spin resonance analysis results confirmed that both 1O2 and SO4•- were the dominant active species in the optimal system, and the redox cycles of Co3+/Co2+ and Mo6+/Mo4+ promoted the generation of the radicals during the PMS activation process. Additionally, the Vis/Co-Mo-TiO2/PMS system exhibited a wide working pH range, superior catalytic performance toward different pollutants and excellent stability with 92.8% SMX removal capacity retention after three consecutive cycles. The result of density functional theory (DFT) suggested that Co-Mo-TiO2 exhibited a high affinity for PMS adsorption, as indicated by the length O-O bond from PMS and the Eads of the catalysts. Finally, the possible degradation pathway of SMX in optimal system was proposed through intermediate identification and DFT calculation, and a toxicity assessment of the by-products was also conducted.

Nitrogen doped magnetic porous carbon derived from starch of oatmeal for efficient activation peroxymonosulfate to degradation sulfadiazine

Nitrogen doped magnetic porous carbon catalyst based on starch of oatmeal was obtained by mixing and pyrolysis process, and its catalytic activity of peroxymonosulfate activation for sulfadiazine degradation was evaluated. When ratio of oatmeal/urea/iron was 1: 2: 0.1, CN@Fe-10 had the best catalytic activity to degrade sulfadiazine. Around 97.8 % removal of 20 mg L^-1 sulfadiazine was achieved under incorporating of 0.05 g L^-1 catalyst and 0.20 g L^-1 peroxymonosulfate. Good adaptability, stability and universality of CN@Fe-10 were verified under different conditions. Electron paramagnetic resonance and radical quenching test suggested that surface-bound reactive oxides species and singlet oxygen were the main reactive oxides species in this reaction. Electrochemical analysis indicated that CN@Fe-10 had a good electrical conductivity and electron transferred did occur among CN@Fe-10 surface, peroxymonosulfate and sulfadiazine. X-ray photoelectron spectroscopy suggested that Fe⁰, Fe₃C, pyridine nitrogen and graphite nitrogen were the potential active sites for peroxymonosulfate activation. Therefore, the work provided a practical approach for recycling biomass.

Degradation and dechlorination of trichloroacetic acid induced by an in situ 222 nm KrCl* excimer radiation

Since the coronavirus disease 2019 (COVID-19) pandemic epidemic, the excessive usage of chlorinated disinfectants raised the substantial risks of disinfection by-products (DBPs) exposure. While several technologies may remove the typical carcinogenic DBPs, trichloroacetic acid (TCAA), their application for continuous treatment is limited due to their complexity and expensive or hazardous inputs. In this study, degradation and dechlorination of TCAA induced by an in situ 222 nm KrCl* excimer radiation as well as role of oxygen in the reaction pathway were investigated. Quantum chemical calculation methods were used to help predict the reaction mechanism. Experimental results showed that UV irradiance increased with increasing input power and decreased when the input power exceeded 60 W. Decomposition and dechlorination were simultaneously achieved, where around 78% of TCAA (0.62 mM) can be eliminated and 78% dechlorination within 200 min. Dissolved oxygen showed little effect on the TCAA degradation but greatly boosted the dechlorination as it can additionally generate hydroxyl radical (•OH) in the reaction process. Computational results showed that under 222 nm irradiation, TCAA was excited from S₀ to S₁ state and then decayed by internal crossing process to T₁ state, and a reaction without potential energy barrier followed, resulting in the breaking of C-Cl bond and finally returning to S₀ state. Subsequent C-Cl bond cleavage occurred by a barrierless •OH insertion and HCl elimination (27.9 kcal/mol). Finally, the •OH attacked (14.6 kcal/mol) the intermediate byproducts, leading to complete dechlorination and decomposition. The KrCl* excimer radiation has obvious advantages in terms of energy efficiency compared to other competitive methods. These results provide insight into the mechanisms of TCAA dechlorination and decomposition under KrCl* excimer radiation, as well as important information for guiding research toward direct and indirect photolysis of halogenated DBPs.

Phosphorus doping significantly enhanced the catalytic performance of cobalt-single-atom catalyst for peroxymonosulfate activation and contaminants degradation

Increasing studies have been conducted to explore strategies for enhancing the catalytic performance of metal-doped C-N-based materials (e.g., cobalt (Co)-doped C₃N₅) via heteroatomic doping. However, such materials have been rarely doped by phosphorus (P) with the higher electronegativity and coordination capacity. In current study, a novel P and Co co-doped C₃N₅ (Co-xP-C₃N₅) was developed for peroxymonosulfate (PMS) activation and 2,4,4'-trichlorobiphenyl (PCB28) degradation. The PCB28 degradation rate increased by 8.16-19.16 times with Co-xP-C₃N₅ compared to conventional activators under similar reaction conditions (e.g., PMS concentration). The state-of-the-art techniques, including X-ray absorption spectroscopy and electron paramagnetic resonance etc., were applied to explore the mechanism of P doping for enhancing Co-xP-C₃N₅ activation. Results showed that P doping induced the formation of Co-P and Co-N-P species, which increased the contents of coordinated Co and improved Co-xP-C₃N₅ catalytic performance. The Co mainly coordinated with the first shell layer of Co₁-N₄, with successful P doping occurring in the second shell layer of Co₁-N₄. The P doping favored electron transfer from the C to N atom near Co sites and thus strengthened PMS activation owing to its higher electronegativity. These findings provide new strategy for enhancing the performance of single atom-based catalysts for oxidant activation and environmental remediation.

Thermal desorption behavior of fluoroquinolones in contaminated soil of livestock and poultry breeding

As a kind of typical veterinary drug, fluoroquinolone antibiotics (FQs) are widely used in the field of livestock and poultry breeding, but these FQs escape to surrounding soil through various pathways, polluting soil through long-term accumulation. Current study proposed a clean technology named thermal desorption to deal with FQs contaminated soils. It was observed that time, temperature and soil particle size were the critical factors in FQs thermal desorption. Results of the study showed that higher temperature was more effective in the removal of FQs, while removal of FQs attached with finer particles was more difficult compared to coarse particles. Fine soil particles (0.6-0.85 mm) were decontaminated up 99.4% when treated with 400 °C for 60min. Thermal desorption of FQs from contaminated soil was governed by first-order kinetics. Based on the detection of exhaust gas components, a possible thermal desorption mechanism was proposed. Study suggested that thermal desorption was a clean and effective remediation method to treat FQs-contaminated soils without generating any further waste.

Monopersulfate in water treatment: Kinetics

The kinetics of monopersulfate based systems in the elimination of potential harmful contaminants has been assessed from a theoretical point of view. A detailed reaction mechanism sustained in the generation of radicals (mainly hydroxyl and sulfate), propagation and termination stages has been proposed. The system of first order differential equations derived has numerically been solved. The effect of main influencing parameters such as contaminant and peroxymonosulfate initial concentrations, intermediate generation, presence of organic matter, role played by anions, has been theoretically obtained. Discussion of simulated results has been accomplished by comparison with experimental data found in the literature. At the sight of the theoretical and empirical data, use of simplistic pseudo first order kinetics is discouraged. Despite considering a significant number of elemental reactions, modelling of the system reveals that a high fraction of them can be neglected due to their insignificant role played in the mechanism. The entire mechanism has been tested when peroxymonosulfate has been activated by UV radiation, although results can be fairly extrapolated to other activation strategies. Finally, a generic model capable of accounting for the effect of a diversity of parameters is proposed. No theoretical background is behind the model, however the generic model clearly improves the results obtained by simple first order kinetics.

Peroxymonosulfate Activation by Photoelectroactive Nanohybrid Filter towards Effective Micropollutant Decontamination

Herein, we report and demonstrate a photoelectrochemical filtration system that enables the effective decontamination of micropollutants from water. The key to this system was a photoelectric–active nanohybrid filter consisting of a carbon nanotube (CNT) and MIL–101(Fe). Various advanced characterization techniques were employed to obtain detailed information on the microstructure, morphology, and defect states of the nanohybrid filter. The results suggest that both radical and nonradical pathways collectively contributed to the degradation of antibiotic tetracycline, a model refractory micropollutant. The underlying working mechanism was proposed based on solid experimental evidences. This study provides new insights into the effective removal of micropollutants from water by integrating state–of–the–art advanced oxidation and microfiltration techniques.

Kinetics and mechanisms of flumequine degradation by sulfate radical based AOP in different water samples containing inorganic anions

Many studies have reported that hydroxyl radical (HO˙) driven advanced oxidation processes (AOPs) could degrade fluoroquinolones (FQs) antibiotics effectively. Compared with HO˙, sulfate radical (SO₄˙⁻) shows a similar oxidation capacity but a longer half-life. SO₄˙⁻ could cause chain reactions and resulted in the generation of halogen radicals and carbonate radicals from the main anions in sea water including Cl⁻, Br⁻ and HCO₃⁻. However, few studies were focused on the degradation of FQs in marine aquaculture water and seawater, as well as the bioaccumulation of transformation products. As a typical member of FQs, flumequine (FLU) was degraded by UV/peroxodisulfate (PDS) AOPs in synthetic fresh water, marine aquaculture water and seawater. The reaction rate constants in the three water samples were 0.0348 min⁻¹, 0.0179 min⁻¹ and 0.0098 min⁻¹, respectively. The reason was attributed to the inhibition of the anions as they could consume SO₄˙⁻ and initiate the quenching reaction of free radicals. When the pH value increased from 5 to 9, the reaction rate decreased from 0.0197 min⁻¹ to 0.0066 min⁻¹. The energy difference between HOMO and LUMO of FLU was calculated to be 8.07 eV indicating that FLU was a stable compound. The atoms on quinolone ring of FLU with high negative charge would be more vulnerable to attack by free radicals through electrophilic reactions. Two possible degradation pathways of FLU were inferred according to the degradation products. Preliminary bioaccumulation analysis of transformation products by the EPI suite software proved that the values of log K_ow and log BCF of the final product P100 were less than those of FLU and the intermediates.

Many studies have reported that hydroxyl radical (HO˙) driven advanced oxidation processes (AOPs) could degrade fluoroquinolones (FQs) antibiotics effectively.