Surfactant effects on water recovery from produced water via direct-contact membrane distillation

Membrane fouling analysis of air-gap membrane distillation (AGMD) for recovery of water and removal of antibiotics from a model wastewater containing antibiotics and humic acid

The study investigates the efficiency of air-gap membrane distillation (AGMD) in water recovery and antibiotics removal from wastewater, focusing on high-concentration scenarios. Experimental findings reveal enhanced membrane performance with increasing the feed temperature, resulting in vapor permeate fluxes of up to 5 kg/m2.h at higher temperatures. Despite experiencing flux reduction caused by fouling from humic acid (HA) in the feed antibiotics solution, the antibiotics consistently maintain near-complete rejection rates (>99%) over 48 h. The foulant on the membrane surface was illustrated by SEM imaging. To know the temperature polarization and the fouling resistance, mathematical modeling was used, and it validates experimental results, elucidating temperature polarization effects and mass transfer coefficients. An increase in feed flow rates reduced thermal boundary layers, enhancing heat flux. Higher temperatures reduced HA fouling resistance. Therefore, AGMD proves effective in water recovery and antibiotics removal, with mathematical models aiding fouling understanding for future research and detailed computational fluid dynamics (CFD) models.

Effect of Organic Cation Adsorption on Ion-Transport Selectivity in a Cation-Permselective Nanopore Membrane

A key knowledge gap in the emerging field of nanofluidics concerns how the ionic composition and ion-transport properties of a nanoconfined solution differ from those of a contacting bulk solution. We and others have been using potentiometric concentration cells, where a nanopore or nanotube membrane separates salt solutions of differing concentrations to explore this issue. The membranes studied contained a fixed pore/tube wall anionic charge, which ideally would prohibit anions and salt from entering the pore/tube-confined solution. We have been investigating experimental conditions that allow for this ideally permselective cation state to be achieved. Results of potentiometric investigations of a polymeric nanopore membrane (10 ± 2 nm-diameter pores) with anionic charge due to carbonate are presented here. While studies of this type have been reported using alkaline metal and alkaline earth cations, there have been no analogous studies using organic cations. This paper uses a homologous series of tetraalkylammonium ions to address this knowledge gap. The key result is that, in contrast to the inorganic cations, the ideal cation-permselective state could not be obtained under any experimental conditions for the organic cations. We propose that this is because these hydrophobic cations adsorb onto the polymeric pore walls. This makes ideality impossible because each adsorbed alkylammonium must bring a charge-balancing anion, Cl-, with it into the nanopore solution. The alkylammonium adsorption that occurred was confirmed and quantified by using surface contact angle measurements.

High Breakthrough Pressure in Hydrogels Enabled Ultrastable Treatment of Hypersaline Wastewaters

Surface effects of low-surface-tension contaminants accumulating at the evaporation surface easily induce wetting in membrane distillation, especially in hypersaline scenarios. Herein, we propose a novel strategy to eliminate the surface effect and redistribute contaminants at the evaporation interface simply by incorporating a layer of hydrogel. The as-fabricated composite membrane exhibits remarkable stability, even when exposed to solution with salt concentration of 5 M and surfactant concentration of 8 mM. Breakthrough pressure of the membrane reaches 20 bar in the presence of surfactants, surpassing commercial hydrophobic membranes by one to two magnitudes. Density functional theory and molecular dynamics simulations reveal the important role of the hydrogel-surfactant interaction in suppressing the surface effect. As a proof of concept, we demonstrate the membrane in stably processing synthetic wastewater containing 144 mg L-1 surfactants, 1 g L-1 mineral oils, and 192 g L-1 NaCl, showing its potential in addressing challenges of hypersaline water treatment.

Recent Advances in Dopamine-Based Membrane Surface Modification and Its Membrane Distillation Applications

Surface modification of membranes is essential for improving flux and resistance to contamination for membranes. This is of great significance for membrane distillation, which relies on the vapor pressure difference across the membrane as the driving force. In recent years, biomimetic mussel-inspired substances have become the research hotspots. Among them, dopamine serves as surface modifiers that would achieve highly desirable and effective membrane applications owing to their unique physicochemical properties, such as universal adhesion, enhanced hydrophilicity, tunable reducibility, and excellent thermal conductivity. The incorporation of a hydrophilic layer, along with the utilization of photothermal properties and post-functionalization capabilities in modified membranes, effectively addresses challenges such as low flux, contamination susceptibility, and temperature polarization during membrane distillation. However, to the best of our knowledge, there is still a lack of comprehensive and in-depth discussions. Therefore, this paper systematically compiles the modification method of dopamine on the membrane surface and summarizes its application and mechanism in membrane distillation for the first time. It is believed that this paper would provide a reference for dopamine-assisted membrane separation during production, and further promote its practical application.

Water and salt recovery from shale gas produced water by vacuum membrane distillation followed by crystallization

A vacuum membrane distillation (VMD) followed by crystallization (VMD-C) was developed for the recovery of water and salts from shale gas produced water (SGPW). Before VMD, the pretreatment of SGPW with Fenton oxidation-flocculation is applied, with the chemical oxygen demand (COD) concentration reduction of 75% and the total removal of the total suspended solids (TSS), Ca2+, and Mg2+ in SGPW. The pretreatment of SGPW mitigated the membrane fouling in the VMD and effectively prevented the reduction of membrane flux over time. The average flux of the PTFE membrane reached 12.1 kg m-2 h-1 during the separation of the pretreated SGPW at a feed flux of 40 L h-1 and a feed temperature of 40 °C. The rejection rate of the membrane to TDS in SGPW was over 99%. Fresh water with a conductivity of below 20 μs cm-1 was produced by VMD-C. The salts concentrated upstream of the membrane were recovered by a stirring crystallization process. The VMD-C system resulted in a 61% cost savings compared to conventional SGPW treatment.

Nanofilament-Coated Superhydrophobic Membranes Show Enhanced Flux and Fouling Resistance in Membrane Distillation

Membrane distillation (MD) is an important technique for brine desalination and wastewater treatment that may utilize waste or solar heat. To increase the distillation rate and minimize membrane wetting and fouling, we deposit a layer of polysiloxane nanofilaments on microporous membranes. In this way, composite membranes with multiscale pore sizes are created. The performance of these membranes in the air gap and direct contact membrane distillation was investigated in the presence of salt solutions, solutions containing bovine serum albumin, and solutions containing the surfactant sodium dodecyl sulfate. In comparison to conventional hydrophobic membranes, our multiscale porous membranes exhibit superior fouling resistance while attaining a higher distillation flux without using fluorinated compounds. This study demonstrates a viable method for optimizing MD processes for wastewater and saltwater treatment.

New Materials and Phenomena in Membrane Distillation

In recent decades, membrane-based processes have been extensively applied to a wide range of industrial processes, including gas separation, food industry, drug purification, and wastewater treatment. Membrane distillation is a thermally driven separation process, in which only vapour molecules transfer through a microporous hydrophobic membrane. At the operational level, the performance of membrane distillation is negatively affected by wetting and temperature polarization phenomena. In order to overcome these issues, advanced membranes have been developed in recent years. This review, which focuses specifically on membrane distillation presents the basic concepts associated with the mass and heat transfer through hydrophobic membranes, membrane properties, and advances in membrane materials. Photothermal materials for solar-driven membrane distillation applications are also presented and discussed.

The advent of thermoplasmonic membrane distillation

Freshwater scarcity is a vital societal challenge related to climate change, population pressure, and agricultural and industrial demands. Therefore, sustainable desalination/purification of salty/contaminated water for human uses is particularly relevant. Membrane distillation is an emerging hybrid thermal-membrane technology with the potential to overcome the drawbacks of conventional desalination by a synergic exploitation of the water-energy nexus. Although membrane distillation is considered a green technology, efficient heat management remains a critical concern affecting the cost of the process and hindering its viability at large scale. A multidisciplinary approach that involves materials chemistry, physical chemistry, chemical engineering, and materials and polymer science is required to solve this problem. The combination of solar energy with membrane distillation is considered a potentially feasible low-cost approach for providing high-quality freshwater with a low carbon footprint. In particular, recent discoveries about efficient light-to-heat conversion in nanomaterials have opened unprecedented perspectives for the implementation of sunlight-based renewable energy in membrane distillation. The integration of nanofillers enabling photothermal effects into membranes has been demonstrated to be able to significantly enhance the energy efficiency without impacting on economic costs. Here, we provide a comprehensive overview on the state of the art, the opportunities, open challenges and pitfalls of the emerging field of solar-driven membrane distillation. We also assess the peculiar physicochemical properties and synthesis scalability of photothermal materials, as well as the strategies for their integration into polymeric nanocomposite membranes enabling efficient light-to-heat conversion and freshwater.

Insights into the wetting phenomenon induced by scaling of calcium sulfate in membrane distillation

Development of water/wastewater treatment based on membrane distillation (MD) suffers from the drawback that the hydrophobic membrane could be wetted for various reasons. Despite significant efforts, there is uncertainty in addressing the wetting induced by scaling of calcium sulfate, which is ubiquitous and recalcitrant in MD processes. This study made the first attempt to analyze the interplay between the growing crystals and the porous structures in the framework of Stoney's equation. Optical coherence tomography (OCT) was exploited to measure the membrane shift, whereby the scaling-induced deformation was correlated with the variation in stress created in the crystal-containing layer. Along with the stress analysis, the OCT-based characterization was combined with conventional approaches to ascertain the dependence of the scaling-induced wetting on the rate of concentrating the crystallizing species when arriving at a high degree of supersaturation in the feed. This study would refine the physical picture for better understanding crystal-membrane interactions that result in not only the wetting phenomenon but also the irreversible damage of membrane structures, thereby lending itself to the development of strategies for MD-based applications with improved efficiency.

Membrane distillation for achieving high water recovery for potable water reuse

Achieving high water recovery using reverse osmosis membranes is challenging during water recycling because the increased concentrations of organics and inorganics in wastewater can cause rapid membrane fouling, necessitating frequent cleaning using chemical agents. This study evaluated the potential of membrane distillation to purify reverse osmosis-concentrated wastewater and achieve 98% overall water recovery for potable water reuse. The results indicate that membrane fouling during membrane distillation treatment was low (4% reduction in permeability) until 98% water recovery. In contrast, membrane fouling during reverse osmosis treatments was high (73% reduction in permeability) before reaching 90% water recovery. Furthermore, membrane distillation showed superior performance in removing dissolved ions (99.9%) from wastewater as compared with reverse osmosis (98.9%). However, although membrane distillation removed most trace organic chemicals tested in this study, a negligible rejection (11%) was observed for N-nitrosodimethylamine, a disinfection byproduct regulated in potable water reuse. In contrast, RO treatment exhibited a high removal of N-nitrosodimethylamine (70%). Post-treatment (e.g., advanced oxidation) after reverse osmosis and membrane distillation may be needed to comply with the N-nitrosodimethylamine regulations. Overall, the membrane distillation process had the capacity to purify reverse osmosis concentrate with insignificant membrane fouling.

Membrane Distillation Hybrid Peroxydisulfate Activation toward Mitigating the Membrane Wetting by Sodium Dodecyl Sulfate

The fouling/wetting of hydrophobic membrane caused by organic substances with low-surface energy substantially limits the development of the membrane distillation (MD) process. The sulfate radical (SO4 ·−)-based advanced oxidation process (AOP) has been a promising technology to degrade organics in wastewater treatment, and peroxydisulfate (PDS) could be efficiently activated by heat. Thus, a hybrid process of MD-AOP via PDS activated by a hot feed was hypothesized to mitigate membrane fouling/wetting. Experiments dealing with sodium dodecyl sulfate (SDS) containing a salty solution via two commercial membranes (PVDF and PTFE) were performed, and varying membrane wetting extents in the coupling process were discussed at different PDS concentrations and feed temperatures. Our results demonstrated permeate flux decline and a rise in conductivity due to membrane wetting by SDS, which was efficiently alleviated in the hybrid process rather than the standalone MD process. Moreover, such a mitigation was enhanced by a higher PDS concentration up to 5 mM and higher feed temperature. In addition, qualitative characterization on membrane coupons wetted by SDS was successfully performed using electrochemical impedance spectroscopy (EIS). The EIS results implied both types of hydrophobic membranes were protected from losing their hydrophobicity in the presence of PDS activation, agreeing with our initial hypothesis. This work could provide insight into future fouling/wetting control strategies for hydrophobic membranes and facilitate the development of an MD process.

Membrane Distillation of Saline Water Contaminated with Oil and Surfactants

Application of the membrane distillation (MD) process for the treatment of high-salinity solutions contaminated with oil and surfactants represents an interesting area of research. Therefore, the aim of this study is to investigate the effect of low-concentration surfactants in oil-contaminated high-salinity solutions on the MD process efficiency. For this purpose, hydrophobic capillary polypropylene (PP) membranes were tested during the long-term MD studies. Baltic Sea water and concentrated NaCl solutions were used as a feed. The feed water was contaminated with oil collected from bilge water and sodium dodecyl sulphate (SDS). It has been demonstrated that PP membranes were non-wetted during the separation of pure NaCl solutions over 960 h of the module exploitation. The presence of oil (100–150 mg/L) in concentrated NaCl solutions caused the adsorption of oil on the membranes surface and a decrease in the permeate flux of 30%. In turn, the presence of SDS (1.5–2.5 mg/L) in the oil-contaminated high-salinity solutions slightly accelerated the phenomenon of membrane wetting. The partial pores’ wetting accelerated the internal scaling and affected degradation of the membrane’s structure. Undoubtedly, the results obtained in the present study may have important implications for understanding the effect of low-concentration SDS on MD process efficiency.

Membrane Distillation for Wastewater Treatment: A Mini Review

Water serves as an indispensable part of human life and production. On account of the overexploitation of traditional water sources, the demand for wastewater recycling is expanding rapidly. As a promising water treatment process, membrane distillation (MD) has been utilized in various wastewater treatments, such as desalination brine, textile wastewater, radioactive wastewater, and oily wastewater. This review summarized the investigation work applying MD in wastewater treatment, and the performance was comprehensively introduced. Moreover, the obstructions of industrialization, such as membrane fouling, membrane wetting, and high energy consumption, were discussed with the practical investigation. To cope with these problems, various strategies have been adopted to enhance MD performance, including coupling membrane processes and developing membranes with specific surface characteristics. In addition, the significance of nutrient recovery and waste heat utilization was indicated.

Effects of pollutants in alkali/surfactant/polymer (ASP) flooding oilfield wastewater on membrane fouling in direct contact membrane distillation by response surface methodology

The characteristic pollutants in alkali/surfactant/polymer (ASP) flooding oilfield wastewater are complex [e.g., NaCl, sodium dodecyl sulfate (SDS), petroleum, and polyacrylamide (PAM)]; thus, membrane distillation (MD) applied to treat this wastewater will be fouled and wetted easily. In this study, response surface methodology (RSM) was used to analyze the effects of pollutant interactions in ASP flooding oilfield wastewater on membrane fouling. The response model showed quantitative relationships between the membrane flux and the pollutant concentrations. The analysis of variance (p-value of the model < 0.0001, p-value of lack of fit > 0.05, R² = 0.9750 and R²_adj = 0.9500) showed that the regression equation fit the empirical data well. The results also indicated that the interactions of pollutants (NaCl and SDS; petroleum and PAM) had significant influence on the flux decline in the simulated ASP flooding oilfield wastewater. The characterization of Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM) revealed that the MD membrane was fouled by simulated ASP flooding oilfield wastewater to a certain degree. Moreover, the membrane flux was restored to 86.9% after hydraulic cleaning.

State-of-the-art management technologies of dissolved methane in anaerobically-treated low-strength wastewaters: A review

The recent advancement in low temperature anaerobic processes shows a great promise for realizing low-energy-cost, sustainable mainstream wastewater treatment. However, the considerable loss of the dissolved methane from anaerobically-treated low-strength wastewater significantly compromises the energy potential of the anaerobic processes and poses an environmental risk. In this review, the promises and challenges of existing and emerging technologies for dissolved methane management are examined: its removal, recovery, and on-site reuse. It begins by describing the working principles of gas-stripping and biological oxidation for methane removal, membrane contactors and vacuum degassers for methane recovery, and on-site biological conversion of dissolved methane into electricity or value-added biochemicals as direct energy sources or energy-compensating substances. A comparative assessment of these technologies in the three categories is presented based on methane treating efficiency, energy-production potential, applicability, and scalability. Finally, current research needs and future perspectives are highlighted to advance the future development of an economically and technically sustainable methane-management technology.

Microfiltration of saline crude oil emulsions: Effects of dispersant and salinity

Dispersants reduce oil-water interfacial tension making the separation of oil-water emulsions challenging. In this study, crude oil stabilized by the dispersant, Corexit EC9500A, was emulsified in synthetic sea water using a range of Corexit/crude oil concentration ratios (up to 10% by volume). With an interfacial tension of only 8.0 mJ/m² at 0.5 mL(Corexit)/L, approximately 50% of the crude was dispersed into droplets <10 µm. Near complete rejection of oil in crossflow separation tests was accompanied by a precipitous flux decline attributable in part to dispersant- and salinity-induced decrease in membrane's oleophobicity (4.2 mJ/m² decrease in surface energy). Screening of electrostatic interactions prompted oil coalescence that occurred at the membrane surface but not in the bulk of the emulsion. Real-time in situ visualization by Direct Observation Through Membrane gave direct evidence of surface coalescence pointing to both its detrimental effects (spread of contiguous films) and possible advantages (removal of large droplets by crossflow shear).

Solar distillation of highly saline produced water using low-cost and high-performance carbon black and airlaid paper-based evaporator (CAPER)

The current technologies to treat hypersaline produced water (PW), such as thermal evaporation, are usually energy-intensive and cost-prohibitive. This study developed a low-cost, robust, solar-driven carbon black and airlaid paper-based evaporator (CAPER) for desalination of PW in the Permian Basin, United States. The study aims to better understand the removal of aromatic organic compounds and heavy metals during solar distillation, water output, and heat transfer. Outdoor experiments using CAPER assisted with polystyrene foam in a single slope, single basin solar still achieved an enhanced average evaporation rate of 2.23 L per m² per day, 165% higher than that of a conventional solar still. Analysis of heat transfer models demonstrated that CAPER solar evaporation achieved an evaporative heat transfer coefficient of ∼28.9 W m^-2·K^-1, 27.9% higher than without CAPER. The maximum fractional energy of evaporation and convection heat transfer inside the solar still with and without CAPER was ∼81.4% and ∼78.2%, respectively. For the PW with a total dissolved solids concentration of 134 g L^-1, solar distillation removed 99.97% salts and over 98% heavy metals. The high removal efficiency of 99.99% was achieved for Ca, Na, Mg, Mn, Ni, Se, Sr, and V. Organic characterization revealed that solar distillation removed over 83% aromatic compounds. Solar desalination using CAPER provides a low-cost and high-performance process to treat PW with high salinity and complex water chemistry for potential fit-for-purpose beneficial uses.

A Critical Review of Membrane Wettability in Membrane Distillation from the Perspective of Interfacial Interactions

Hydrophobic membranes used in membrane distillation (MD) systems are often subject to wetting during long-term operation. Thus, it is of great importance to fully understand factors that influence the wettability of hydrophobic membranes and their impact on the overall separation efficiency that can be achieved in MD systems. This Critical Review summarizes both fundamental and applied aspects of membrane wetting with particular emphasis on interfacial interaction between the membrane and solutes in the feed solution. First, the theoretical background of surface wetting, including the relationship between wettability and interfacial interaction, definition and measurement of contact angle, surface tension, surface free energy, adhesion force, and liquid entry pressure, is described. Second, the nature of wettability, membrane wetting mechanisms, influence of membrane properties, feed characteristics and operating conditions on membrane wetting, and evolution of membrane wetting are reviewed in the context of an MD process. Third, specific membrane features that increase resistance to wetting (e.g., superhydrophobic, omniphobic, and Janus membranes) are discussed briefly followed by the comparison of various cleaning approaches to restore membrane hydrophobicity. Finally, challenges with the prevention of membrane wetting are summarized, and future work is proposed to improve the use of MD technology in a variety of applications.

A Mini Review on Antiwetting Studies in Membrane Distillation for Textile Wastewater Treatment

The textile industry is an important contributor to the growth of the global economy. However, a huge quantity of wastewater is generated as a by-product during textile manufacturing, which hinders the ongoing development of textile industry in terms of environmental sustainability. Membrane distillation (MD), which is driven by thermal-induced vapor pressure difference, is being considered as an emerging economically viable technology to treat the textile wastewater for water reuse. So far, massive efforts have been put into new membrane material developments and modifications of the membrane surface. However, membrane wetting, direct feed solution transport through membrane pores leading to the failure of separation, remains as one of the main challenges for the success and potential commercialization of this separation process as textile wastewater contains membrane wetting inducing surfactants. Herein, this review presents current progress on the MD process for textile wastewater treatment with particular focuses on the fundamentals of membrane wetting, types of membranes applied as well as the fabrication or modification of membranes for anti-wetting properties. This article aims at providing insights in membrane design to enhance the MD separation performance towards commercial application of textile wastewater treatment.

Fluorinated silica-modified anti-oil-fouling omniphobic F-SiO2@PES robust membrane for multiple foulants feed in membrane distillation

Direct-contact membrane distillation (DCMD) can be eminent solution for oily wastewater treatment if the membrane provided is slippery and tolerant to low surface tension complex solutions. This study describes preparation of an anti-oil-fouling omniphobic polyethersulfone membrane using fluorinated silica nanoparticles (F-SiO₂@PES) combined with perfluorodecyl triethoxysilane and polydimethylsiloxane for application against oil-In-water (o/w) emulsions. Feed solutions consist of different concentrations of oil (hexadecane), different charge surfactants (anionic sodium dodecyl benzenesulfonate, non-ionic Tween 20, and cationic hexadecyltrimethylammonium bromide, and salt (NaCl). The hierarchical re-entrant micro structured surface of the omniphobic F-SiO₂@PES membrane and functional groups are confirmed by atomic force microscopy, scanning electron microscopy, and Fourier-transform infrared spectroscopy. The anti-oil-fouling and anti-wetting performance of omniphobic F-SiO₂@PES membranes are investigated using contact-angle, sliding angles, DCMD tests with multiple foulants of surfactants. Omniphobic F-SiO₂@PES membrane exhibited effective anti-oil-fouling and anti-wetting performance against emulsions as no severe fouling and a conductivity rises were evident regardless of surfactant charge and the concentration of components. Flux reduction and rejection rates for the omniphobic F-SiO₂@PES membranes are in a range of 5-15% (only) and >99%, respectively, for various combinations of feed solution components.

Impact of Inorganic Ions and Organic Matter on the Removal of Trace Organic Contaminants by Combined Direct Contact Membrane Distillation-UV Photolysis

This study investigated the degradation of five trace organic contaminants (TrOCs) by integrated direct contact membrane distillation (DCMD) and UV photolysis. Specifically, the influence of inorganic ions including halide, nitrate, and carbonate on the performance of the DCMD–UV process was evaluated. TrOC degradation improved in the presence of different concentrations (1–100 mM) of fluoride ion and chloride ion (1 mM). With a few exceptions, a major negative impact of iodide ion was observed on the removal of the investigated TrOCs. Of particular interest, nitrate ion significantly improved TrOC degradation, while bicarbonate ion exerted variable influence—from promoting to inhibiting impact—on TrOC degradation. The performance of DCMD–UV photolysis was also studied for TrOC degradation in the presence of natural organic matter, humic acid. Results indicated that at a concentration of 1 mg/L, humic acid improved the degradation of the phenolic contaminants (bisphenol A and oxybenzone) while it inhibited the degradation of the non-phenolic contaminants (sulfamethoxazole, carbamazepine, and diclofenac). Overall, our study reports the varying impact of different inorganic and organic ions present in natural water on the degradation of TrOCs by integrated DCMD–UV photolysis: the nature and extent of the impact of the ions depend on the type of TrOCs and the concentration of the interfering ions.

Activated sludge treatment for promoting the reuse of a synthetic produced water in irrigation

Large volumes of produced water are generated as a byproduct in activities of oil and gas exploitation, which can be reused in agriculture after a treatment process. Activated sludge treatment has been successfully used to remove oil from wastewater, but systematic studies on the toxicity of this effluent using this treatment are scarce in the literature. In this study, it was investigated the performance of an activated sludge system in the treatment of a synthetic produced water under different initial conditions in terms of salinity and oil and grease concentration. Furthermore, it was evaluated this effluent phytotoxicity in the germination, and seedling and plant growths of sunflower and corn seeds using untreated and treated synthetic produced water. Results revealed the activated sludge effectiveness in oil and grease and salinity removal from produced water, viz. high removal efficiency of 99.01 ± 0.28 and 91.07 ± 0.39%., respectively. Untreated produced water showed considerable toxic effects on the germination (74.67 ± 2.31% and 82.67 ± 2.31 for sunflower and corn seeds, respectively) and growth stages of sunflower and corn seed plants. The germination percentage was approximately 100% for both types of seed. The seedling and plant growth of the two seeds irrigated with treated produced water had similar performance when used tap water. These results highlighted the potential reuse as an unconventional water resource for plant irrigation of the synthetic produced water treated by an activated sludge process, which technology has showed high removal performance of salinity and oil.

Enhancing the Antibacterial Properties of PVDF Membrane by Hydrophilic Surface Modification Using Titanium Dioxide and Silver Nanoparticles

This work investigates polyvinylidene fluoride (PVDF) membrane modification to enhance its hydrophilicity and antibacterial properties. PVDF membranes were coated with nanoparticles of titanium dioxide (TiO₂-NP) and silver (AgNP) at different concentrations and coating times and characterized for their porosity, morphology, chemical functional groups and composition changes. The results showed the successfully modified PVDF membranes containing TiO₂-NP and AgNP on their surfaces. When the coating time was increased from 8 to 24 h, the compositions of Ti and Ag of the modified membranes were increased from 1.39 ± 0.13 to 4.29 ± 0.16 and from 1.03 ± 0.07 to 3.62 ± 0.08, respectively. The water contact angle of the membranes was decreased with increasing the coating time and TiO₂-NP/AgNP ratio. The surface roughness and permeate fluxes of coated membranes were increased due to increased hydrophilicity. Antimicrobial and antifouling properties were investigated by the reduction of Escherichia coli cells and the inhibition of biofilm formation on the membrane surface, respectively. Compared with that of the original PVDF membrane, the modified membranes exhibited antibacterial efficiency up to 94% against E. coli cells and inhibition up to 65% of the biofilm mass reduction. The findings showed hydrophilic improvement and an antimicrobial property for possible wastewater treatment without facing the eminent problem of biofouling.

Interplay of the Factors Affecting Water Flux and Salt Rejection in Membrane Distillation: A State-of-the-Art Critical Review

High water flux and elevated rejection of salts and contaminants are two primary goals for membrane distillation (MD). It is imperative to study the factors affecting water flux and solute transport in MD, the fundamental mechanisms, and practical applications to improve system performance. In this review, we analyzed in-depth the effects of membrane characteristics (e.g., membrane pore size and distribution, porosity, tortuosity, membrane thickness, hydrophobicity, and liquid entry pressure), feed solution composition (e.g., salts, non-volatile and volatile organics, surfactants such as non-ionic and ionic types, trace organic compounds, natural organic matter, and viscosity), and operating conditions (e.g., temperature, flow velocity, and membrane degradation during long-term operation). Intrinsic interactions between the feed solution and the membrane due to hydrophobic interaction and/or electro-interaction (electro-repulsion and adsorption on membrane surface) were also discussed. The interplay among the factors was developed to qualitatively predict water flux and salt rejection considering feed solution, membrane properties, and operating conditions. This review provides a structured understanding of the intrinsic mechanisms of the factors affecting mass transport, heat transfer, and salt rejection in MD and the intra-relationship between these factors from a systematic perspective.

Environmental impact of utilization of "produced water" from oil and gas operations in turfgrass systems

This study attempted to use produced water (PW) to irrigate turfgrass species, Cynodon dactylon and Paspalum sp. Assessment on established grasses, heavy metal accumulation and germination tests for weeds and turf grass seeds were conducted to evaluate the impact of PW irrigation. C. dactylon depicted lower tolerance while Paspalum sp. showed better tolerance capacity towards PW. C. dactylon grown from seeds under greenhouse conditions were not able to tolerate more than 30% concentration of PW (4.5% salinity). In comparison to tap water irrigated turf grass, Paspalum sp. was found to accumulate higher concentrations of V and Pb in shoots and Cr, Ni and As in roots. The results of seed germination tests recommended that irrigation with PW is to be performed after turfgrass establishment. Germination tests also revealed that PW could encourage growth of the weed-Chloris virgata while it could discourage growth of Amaranthus viridis and Launaea mucronata. This study suggests that PW could be used for turfgrass as an alternative water resource but only after further research on the long-term scale.

Direct contact membrane distillation for effective concentration of perfluoroalkyl substances - Impact of surface fouling and material stability

Polyfluoroalkyl and perfluoroalkyl substances (PFAS) are ecotoxic amphiphilic compounds containing alkyl-fluorinated chains terminated with weak acid moieties, and hence difficult to be degraded or removed from water sources. Direct contact membrane distillation (DCMD) was used for concentrating and removing of perfluoropentanoic acid (PFPeA) compounds from model contaminated water using commercially available poly (tetrafluoroethylene) (PTFE) membranes. The membranes were characterised for surface morphology, roughness, contact angle and pore size distribution before and after the DCMD test to investigate and evaluate membrane fouling. During the DCMD test performed for 6 h using 10 ppm PFPeA solution, the membrane exhibited progressive increased flux (from 17 to 43 kg m^-2 h^-1) and decreased PFPeA rejection (from 85 to 58%), as the feed temperature was increased from 50 to 70 °C. Further, the feed/retentate side showed a 1.8, 2.1 and 2.8-fold increase in PFPeA concentration tested at feed temperatures 50, 60, and 70 °C, respectively. The permeate side contained less than 1 ppm of PFPeA revealing that the PFPeA moved across the PTFE membrane during DCMD, which is attributed to progressive surface diffusion over time. This study opens a new route to concentrate and remove amphiphilic molecules, such as PFAS, from source points, relevant to landfill leachates or surface waters. The study also points at gaps in materials science and surface engineering to be tackled to deal with PFAS compounds efficiently.

Recent Advances in Applications of Carbon Nanotubes for Desalination: A Review

As a sustainable, cost-effective and energy-efficient method, membranes are becoming a progressively vital technique to solve the problem of the scarcity of freshwater resources. With these critical advantages, carbon nanotubes (CNTs) have great potential for membrane desalination given their high aspect ratio, large surface area, high mechanical strength and chemical robustness. In recent years, the CNT membrane field has progressed enormously with applications in water desalination. The latest theoretical and experimental developments on the desalination of CNT membranes, including vertically aligned CNT (VACNT) membranes, composited CNT membranes, and their applications are timely and comprehensively reviewed in this manuscript. The mechanisms and effects of CNT membranes used in water desalination where they offer the advantages are also examined. Finally, a summary and outlook are further put forward on the scientific opportunities and major technological challenges in this field.

Separation of saline oily wastewater by membrane distillation

Membrane distillation was used for the treatment of saline oily wastewaters collected from harbour deoiling installation. The turbidity of these wastewaters was in the range 63–87 NTU, salt concentration was 6–11 g/L and the oil content in the feed was below 40 mg/L. Two types of commercial polypropylene capillary membranes were applied for the process study. The intensive membrane fouling during the wastewater separation was observed. Modules rinsed with water removed the organic deposits formed. However, the CaCO3 scale was accumulated on the membrane surfaces during 1500 h of the process, resulting in a permeate flux decline by more than 40%. The initial yield of modules was recovered by membrane rinsing with 5 wt% HCl solution. The long-term studies demonstrated that the separated oily wastewaters did not cause wetting of the applied membrane. The degree of retention amounted to 98% for the inorganic compounds and more than 99% for the organic compounds.

Anti-oil-fouling hydrophobic-superoleophobic composite membranes for robust membrane distillation performance

As a promising thermally driven separation process, membrane distillation (MD) is capable of treating challenging wastewaters. However, the traditional hydrophobic membranes are vulnerable to fouling by non-polar contaminants owing to the strong hydrophobic-hydrophobic interactions. To address this problem, we developed novel anti-oil-fouling MD membranes in this study. The composite membranes with asymmetric wettability were fabricated through electrospinning polyacrylonitrile (PAN) fibrous coating on a hydrophobic polytetrafluoroethylene (PTFE) membrane, followed by hydrolyzing the PAN coating with ethylenediamine (EDA) and NaOH, respectively. These two composite membranes exhibited excellent underwater superoleophobicity, with the underwater oil contact angle >150°, which can be attributed to the fibrous and re-entrant surface structure and the optimized surface hydrophilicity of the electrospun coating. During MD process using saline and oily emulsion as feed, the composite membranes presented robust anti-oil-fouling performance, indicating by stable permeate flux and salt rejection. A novel oil-droplet adhesion force probe was introduced to quasi-quantitatively elucidate oil-membrane interaction and evaluate membrane fouling propensity, the force spectroscopy indicated that the fabricated composite membranes had fairly less attractive to crude oil compared with the PTFE membrane. Our research results suggest that the novel composite membranes with asymmetric wettability were competent to serve as an anti-oil-fouling MD membrane for desalinating challenging saline and oily wastewaters.

Recent advances in membrane development for treating surfactant- and oil-containing feed streams via membrane distillation

Membrane distillation (MD) has been touted as a promising technology for niche applications such as desalination of surfactant- and oil-containing feed streams. Hitherto, the deployment of conventional hydrophobic MD membranes for such applications is limited and unsatisfactory. This is because the presence of surfactants and oils in aqueous feed streams reduces the surface-tension of these media significantly and the attachment of these contaminants onto hydrophobic membrane surfaces often leads to membrane fouling and pore wetting, which compromises on the quantity and quality of water recovered. Endowing MD membranes with surfaces of special wettabilities has been proposed as a strategy to combat membrane fouling and pore wetting. This involves the design of local kinetic energy barriers such as multilevel re-entrant surface structures, surfaces with ultralow surface-energies, and interfacial hydration layers to impede transition to the fully-wetted Wenzel state. This review critiques the state-of-the-art fabrication and surface-modification methods as well as practices used in the development of omniphobic and Janus MD membranes with specific emphasis on the advances, challenges, and future improvements for application in challenging surfactant- and oil-containing feed streams.