A novel green solvent alternative for polymeric membrane preparation via nonsolvent-induced phase separation (NIPS)

Interconnected Nanoporous Polysulfone by the Self-Assembly of Randomly Linked Copolymer Networks and Linear Multiblocks

Porous materials have attracted considerable attention due to their versatile applications, especially in water purification. Interconnected nanoporous structures are distinguished by their high degree of porosity and resistance to clogging, as well as their insensitivity to nanostructural orientation. Previous works on randomly linked copolymer systems have shown that they can effectively produce disordered cocontinuous nanostructures, which upon removal of one component yield interconnected nanoporous materials. However, the cocontinuous nanomaterials previously developed using polystyrene (PS) and poly(d,l-lactic acid) (PLA) strands, and the resulting interconnected nanoporous PS monoliths, were far too brittle to enable practical use as membranes. Here, we study the self-assembly of randomly linked copolymer networks prepared using blocks of the engineering polymer polysulfone (PSU). A wide cocontinuous regime (spanning 40 wt %) was found for randomly end-linked copolymer networks (RECNs) constructed from PSU and PLA strands, via a combination of mechanical testing, gravimetry, small-angle X-ray scattering, and scanning electron microscopy. The PSU/PLA cocontinuous nanomaterial with symmetric composition showed 2.4 times higher Young's modulus and ∼100 times greater toughness than the corresponding PS/PLA sample. The interconnected nanoporous PSU fabricated after etching of PLA even exhibited 1.6 times greater toughness than PS/PLA prior to PLA removal. To facilitate the production of thin films of cocontinuous nanomaterials, we applied solution-processable randomly linked linear PSU/PLA multiblock polymers onto ultrafiltration membranes. The interconnected nanoporous PSU thin film generated by etching PLA was found to effectively reject 50 nm diameter particles without significantly compromising permeability. This discovery presents a valuable addition to the existing techniques used to fabricate PSU membranes. In contrast to traditional methods, which are sensitive to processing conditions, produce a wide range of pore sizes, and offer limited adjustability of pore size, the current technique is anticipated to enable interconnected PSU membranes with more uniform and tailorable porosity.

Synthesis and Characterization of Polyaniline Emeraldine Salt (PANI-ES) Colloids Using Potato Starch as a Stabilizer to Enhance the Physicochemical Properties and Processability

Conductive polymers, such as polyaniline (PANI), have interesting applications, ranging from flexible electronics, energy storage devices, sensors, antistatic or anticorrosion coatings, etc. However, the full exploitation of conductive polymers still poses a challenge due to their low processability. The use of compatible stabilizers to obtain dispersible and stable colloids is among the possible solutions to overcome such drawbacks. In this work, potato starch was used as a steric stabilizer for the preparation of colloidal polyaniline (emeraldine salt, ES)/starch composites by exploiting the oxidative polymerization of aniline in aqueous solutions with various starch-to-aniline ratios. The polyaniline/starch bio-composites were subjected to structural, spectroscopic, thermal, morphological, and electrochemical analyses. The samples were then tested for their dispersibility/solubility in a range of organic solvents. The results demonstrated the formation of PANI/starch biocomposites with a smaller average size than starch particles, showing improved aqueous dispersion and enhanced solubility in organic solvents. With respect to previously reported PANI-EB (emeraldine base)/starch composites, the novel colloids displayed a lower overall crystallinity, but the conductive nature of PANI-ES enhanced its electrochemical properties, resulting in richer redox chemistry, particularly evident in its oxidation behavior, as observed through cyclic voltammetry. Finally, as proof of the improved processability, the colloids were successfully integrated into a thin polyether sulfone (PES) membrane.

Cellulose-based materials in environmental protection: A scientometric and visual analysis review

As sustainable materials, cellulose-based materials have attracted significant attention in the field of environmental protection, resulting in the publication of numerous academic papers. However, there is a scarcity of literature that involving scientometric analysis within this specific domain. This review aims to address this gap and highlight recent research in this field by utilizing scientometric analysis and a historical review. As a result, 21 highly cited articles and 10 mostly productive journals were selected out. The scientometric analysis reveals that recent studies were objectively clustered into five interconnected main themes: extraction of cellulose from raw materials and its degradation, adsorption of pollutants using cellulose-based materials, cellulose-acetate-based membrane materials, nanocellulose-based materials, and other cellulose-based materials such as carboxymethyl cellulose and bacterial cellulose for environmental protection. Analyzing the distribution of author keywords and thoroughly examining relevant literature, the research focuses within these five themes were summarized. In the future, the development of eco-friendly and cost-effective methods for extracting and preparing cellulose and its derivatives, particularly nanocellulose-based materials, remains an enduring pursuit. Additionally, machine learning techniques holds promise for the advancement and application of cellulose-based materials. Furthermore, there is potential to expand the research and application scope of cellulose-based materials for environmental protection.

Progress in the Preparation and Application of Breathable Membranes

Breathable membranes with micropores enable the transfer of gas molecules while blocking liquids and solids, and have a wide range of applications in medical, industrial, environmental, and energy fields. Breathability is highly influenced by the nature of a material, pore size, and pore structure. Preparation methods and the incorporation of functional materials are responsible for the variety of physical properties and applications of breathable membranes. In this review, the preparation methods of breathable membranes, including blown film extrusion, cast film extrusion, phase separation, and electrospinning, are discussed. According to the antibacterial, hydrophobic, thermal insulation, conductive, and adsorption properties, the application of breathable membranes in the fields of electronics, medicine, textiles, packaging, energy, and the environment are summarized. Perspectives on the development trends and challenges of breathable membranes are discussed.

Waste treats waste: Facile fabrication of porous adsorbents from recycled PET and sodium alginate for efficient dye removal

Dye-contaminated water and waste plastic both pose enormous threats to human health and the ecological environment, and simultaneously solving these two issues in a sustainable and resource-saving way is highly important. In this work, a sodium alginate-polyethylene terephthalate-sodium alginate (SA@PET) composite adsorbent for efficient dye removal is fabricated using wasted PET bottle and marine plant-based SA via simple and energy-efficient nonsolvent-induced phase separation (NIPS) method. Benefiting from its porous structure and the abundant binding sites, SA@PET shows an excellent methylene blue (MB) adsorption capacity of 1081 mg g-1. The Redlich-Peterson model more accurately describes the adsorption behavior, suggesting multiple adsorption mechanisms. In addition to the electrostatic attractions of SA to MB, polar interactions between the PET matrix and MB are also identified as adsorption mechanisms. It is worth mentioning that SA@PET could be recycled 7 times without a serious decrease in performance, and the trifluoroacetic acid-dichloromethane solvent involved in the NIPS process has the possibility of reuse and stepwise recovery. Finally, the discarded adsorbent could be completely degraded under mild conditions. This work provides not only a composite adsorbent with excellent cationic dye removal performance for wastewater treatment, but also an upcycling strategy for waste PET.

Influence of citric acid concentrations on the porosity and performance of cellulose acetate-based porous membranes: A comprehensive study

This study investigates the influence of citric acid concentration on the fabrication of porous cellulose acetate (CA) membranes using the Non-Solvent Induced Phase Separation (NIPS) method. A notable aspect is the precise control over membrane properties, particularly pore size and porosity, achieved solely through the adjustment of citric acid concentration, serving as the additive. Higher concentrations of citric acid increase pore size by rendering polymer chains more pliable, whereas lower concentrations lead to smaller, denser pores due to improved dispersion in the CA matrix and altered water interactions during phase separation. A decrease in porosity and Gurley values with reducing citric acid concentrations (from 5 × 10-2 to 1 × 10-3 M ratios) indicates less plasticization of CA chains. However, at very low concentrations (1 × 10-4 and 1 × 10-5), porosity increases, despite the presence of smaller pores, and Gurley values approach those of pure CA in terms of gas permeability. Fourier Transform Infrared (FT-IR) spectroscopy confirms the presence of citric acid and its interaction with carbonyl groups, consistent with the pore size observations from Scanning Electron Microscopy (SEM). Spectral data deconvolution reveals weakened carbonyl bonds due to the reduced presence of citric acid, correlating with the smaller pores observed in SEM. Thermal Gravimetric Analysis (TGA) demonstrates that composite membranes are more thermally stable than pure CA, attributed to the citric acid-induced crosslinking within the polymer chains. Stability increases with decreasing citric acid concentration, with some anomalies at the lowest levels. In conclusion, this study highlights the capability of adjusting citric acid concentration to tailor membrane properties, offering valuable insights for the creation of porous materials across diverse industrial applications.

Highly Stretchable Thermoplastic Polyurethane Separators for Li-Ion Batteries Based on Non-Solvent-Induced Phase Separation Method

The growing interest in wearable and portable devices has stimulated the need for flexible and stretchable lithium-ion batteries (LiBs). A crucial component in these batteries is the separator, which provides a pathway for Li-ion transfer and prevents electrode contact. In a flexible and stretchable LiB, the separator must exhibit stretchability and elasticity akin to its existing counterparts. Here, we developed a non-modified thermoplastic polyurethane (TPU) separator using the non-solvent induced phase separation (NIPS) technique. We compared their performance with commercially available polypropylene (PP) separators. Our results demonstrate that TPU separators exhibit superior elasticity based on repeated stretch/release tests with excellent thermal stability and electrolyte wettability. Furthermore, our findings confirm that TPU separators, even after being repeatedly stretched and released, can function effectively without severe damage in a fabricated coin cell LiB with high oxidative stability, as evidenced by linear sweep voltammetry, like commercially available separators.

Green Synthesis of Cation Exchange Membranes: A Review

Cation exchange membranes (CEMs) play a significant role in the transition to a more sustainable/green society. They are important components for applications such as water electrolysis, artificial photosynthesis, electrodialysis and fuel cells. Their synthesis, however, is far from being sustainable, affecting safety, health and the environment. This review discusses and evaluates the possibilities of synthesizing CEMs that are more sustainable and green. First, the concepts of green and sustainable chemistry are discussed. Subsequently, this review discusses the fabrication of conventional perfluorinated CEMs and how they violate the green/sustainability principles, eventually leading to environmental and health incidents. Furthermore, the synthesis of green CEMs is presented by dividing the synthesis into three parts: sulfonation, material selection and solvent selection. Innovations in using gaseous SO3 or gas-liquid interfacial plasma technology can make the sulfonation process more sustainable. Regarding the selection of polymers, chitosan, cellulose, polylactic acid, alginate, carrageenan and cellulose are promising alternatives to fossil fuel-based polymers. Finally, water is the most sustainable solvent and many biopolymers are soluble in it. For other polymers, there are a limited number of studies using green solvents. Promising solvents are found back in other membrane, such as dimethyl sulfoxide, Cyrene™, Rhodiasolv® PolarClean, TamiSolve NxG and γ-valerolactone.

Enhanced porous membrane fabrication using cellulose acetate and citric acid: Improved structural integrity, thermal stability, and gas permeability

In this study, our primary objective was to enhance the properties of porous membranes by addressing the limitations associated with phase separation. We employed a non-solvent induced phase separation (NIPS) method, utilizing cellulose acetate (CA) in conjunction with citric acid to fabricate these membranes. Citric acid played a dual role: ensuring a uniform pore structure and cross-linking the CA polymer, thereby enhancing its mechanical strength. This approach resulted in the development of a more robust membrane with superior structural integrity. Thermogravimetric analysis (TGA) confirmed enhanced thermal stability, particularly up to 150 °C, as a result of citric acid's cross-linking effect. Beyond 150 °C, the decomposition temperatures of the CA/citric acid membrane were found to be comparable to those of pure CA. Remarkably, a CA/citric acid ratio of 1:0.05 exhibited the slowest decomposition rate as the temperature increased. Scanning electron microscopy (SEM) examination unveiled a sponge-like membrane structure with numerous evenly distributed fine pores. Through the use of citric acid as a plasticizer, we were able to effectively control the penetration of water molecules, preventing the formation of macrovoids and promoting the creation of fine pores. This resulted in the fabrication of a high-porosity membrane, boasting an impressive porosity measurement of 84.9 %. Furthermore, measurements of the Gurley value confirmed efficient gas permeation, a critical characteristic for applications requiring effective gas transport. Fourier transform infrared (FT-IR) spectroscopy attested to the presence of citric acid in the membrane post-phase separation, indicating its successful integration. Our work presents a novel approach to enhance porous membranes, providing improvements in mechanical strength, thermal stability, and gas permeability. These findings offer valuable insights for the development of advanced materials with diverse applications in various fields.

Hollow Filaments from Coaxial Dry-Jet Wet Spinning of a Cellulose Solution in an Ionic Liquid: Wet-Strength and Water Interactions

Hollow tubing and tubular filaments are highly relevant to membrane technologies, vascular tissue engineering, and others. In this context, we introduce hollow filaments (HF) produced through coaxial dry-jet wet spinning of cellulose dissolved in an ionic liquid ([emim][OAc]). The HF, developed upon regeneration in water (23 °C), displays superior mechanical performance (168 MPa stiffness and 60% stretchability) compared to biobased counterparts, such as those based on collagen. The results are rationalized by the effects of crystallinity, polymer orientation, and other factors associated with rheology, thermal stability, and dynamic vapor sorption. The tensile strength and strain of the HF (dry and wet) are enhanced by drying and wetting cycles (water vapor sorption and desorption experiments). Overall, we unveil the role of water molecules in the wet performance of HF produced by cellulose regeneration from [emim][OAc], which offers a basis for selecting suitable applications.

Mechanism of PVDF Membrane Formation by NIPS Revisited: Effect of Precipitation Bath Nature and Polymer-Solvent Affinity

A new interpretation of the mechanism of the polyvinylidene fluoride (PVDF) membrane formation using the nonsolvent-induced phase separation (NIPS) method based on an analysis of the complete experimental phase diagram for the three-component mixture PVDF-dimethyl acetamide (DMAc)-water is proposed. The effects of the precipitation bath's harshness and thermodynamic affinity of the polymer's solvent on the morphology, crystalline structure, transport and physical-mechanical properties of the membranes are investigated. These characteristics were studied via scanning electron microscopy, wide-angle X-ray scattering, liquid-liquid porosimetry and standard methods of physico-mechanical analysis. It is established that an increase in DMAc concentration in the precipitation bath results in the growth of mean pore size from ~60 to ~150 nm and an increase in permeance from ~2.8 to ~8 L m-2 h-1 bar-1. It was observed that pore size transformations are accompanied by changes in the tensile strength of membranes from ~9 to ~11 and to 6 MPa, which were explained by the degeneration of finger-like pores and appearance of spherulitic structures in the samples. The addition of water to the dope solution decreased both the transport (mean pore size changed from ~55 to ~25 nm and permeance reduced from ~2.8 to ~0.5 L m-2 h-1 bar-1) and mechanical properties of the membranes (tensile strength decreased from ~9 to ~6 MPa). It is possible to conclude that the best membrane quality may be reached using pure DMAc as a solvent and a precipitation bath containing 10-30% wt. of DMAc, in addition to water.

Thermodynamics and kinetic analysis of membrane: Challenges and perspectives

The ultimate structure of the membrane is determined using two important effects: (i) thermodynamic effect and (ii) kinetic effect. Controlling the mechanism of kinetic and thermodynamic processes in phase separation is essential for enhancing membrane performance. However, the relationship between system parameters and the ultimate membrane morphology is still largely empirical. This review focuses on the fundamental ideas behind thermally induced phase separation (TIPS) and nonsolvent-induced phase separation (NIPS) methods, including both kinetic and thermodynamic elements. The thermodynamic approach to understanding phase separation and the effect of different interaction parameters on membrane morphology has been discussed in detail. Furthermore, this review explores the capabilities and limitations of different macroscopic transport models used for the last four decades to explore the phase inversion process. The application of molecular simulations and phase field to understand phase separation has also been briefly examined. Finally, it discusses the thermodynamic approach to understanding phase separation and the consequence of different interaction parameters on membrane morphology, as well as possible directions for artificial intelligence to fill the gaps in the literature. This review aims to provide comprehensive knowledge and motivation for future modeling work for membrane fabrication via new techniques such as nonsolvent-TIPS, complex-TIPS, non-solvent assisted TIPS, combined NIPS-TIPS method, and mixed solvent phase separation.

Green and Sustainable Membranes: A review

Membranes are ubiquitous tools for modern water treatment technology that critically eliminate hazardous materials such as organic, inorganic, heavy metals, and biomedical pollutants. Nowadays, nano-membranes are of particular interest for myriad applications such as water treatment, desalination, ion exchange, ion concentration control, and several kinds of biomedical applications. However, this state-of-the-art technology suffers from some drawbacks, e.g., toxicity and fouling of contaminants, which makes the synthesis of green and sustainable membranes indeed safety-threatening. Typically, sustainability, non-toxicity, performance optimization, and commercialization are concerns centered on manufacturing green synthesized membranes. Thus, critical issues related to toxicity, biosafety, and mechanistic aspects of green-synthesized nano-membranes have to be systematically and comprehensively reviewed and discussed. Herein we evaluate various aspects of green nano-membranes in terms of their synthesis, characterization, recycling, and commercialization aspects. Nanomaterials intended for nano-membrane development are classified in view of their chemistry/synthesis, advantages, and limitations. Indeed, attaining prominent adsorption capacity and selectivity in green-synthesized nano-membranes requires multi-objective optimization of a number of materials and manufacturing parameters. In addition, the efficacy and removal performance of green nano-membranes are analyzed theoretically and experimentally to provide researchers and manufacturers with a comprehensive image of green nano-membrane efficiency under real environmental conditions.

Development of a Green Polymeric Membrane for Sodium Diclofenac Removal from Aqueous Solutions

Water-soluble polymers provide an alternative to organic solvent requirements in membrane manufacture, aiming at accomplishing the Green Chemistry principles. Poly(vinyl alcohol) (PVA) is a biodegradable and non-toxic polymer renowned for its solubility in water. However, PVA is little explored in membrane processes due to its hydrophilicity, which reduces its stability and performance. Crosslinking procedures through an esterification reaction with carboxylic acids can address this concern. For this, experimental design methodology and statistical analysis were employed to achieve the optimal crosslinking conditions of PVA with citric acid as a crosslinker, aiming at the best permeate production and sodium diclofenac (DCF) removal from water. The membranes were produced following an experimental design and characterized using multiple techniques to understand the effect of crosslinking on the membrane performance. Characterization and filtration results demonstrated that crosslinking regulates the membranes' properties, and the optimized conditions (crosslinking at 110 °C for 110 min) produced a membrane able to remove 44% DCF from water with a permeate production of 2.2 L m^-2 h^-1 at 3 bar, comparable to commercial loose nanofiltration membranes. This study contributes to a more profound knowledge of green membranes to make water treatment a sustainable practice in the near future.

Fabrication and Evaluation of Filtration Membranes from Industrial Polymer Waste

Polyvinylidene fluoride (PVDF) polymers are known for their diverse range of industrial applications and are considered important raw materials for membrane manufacturing. In view of circularity and resource efficiency, the present work mainly deals with the reusability of waste polymer 'gels' produced during the manufacturing of PVDF membranes. Herein, solidified PVDF gels were first prepared from polymer solutions as model waste gels, which were then subsequently used to prepare membranes via the phase inversion process. The structural analysis of fabricated membranes confirmed the retention of molecular integrity even after reprocessing, whereas the morphological analysis showed a symmetric bi-continuous porous structure. The filtration performance of membranes fabricated from waste gels was studied in a crossflow assembly. The results demonstrate the feasibility of gel-derived membranes as potential microfiltration membranes exhibiting a pure water flux of 478 LMH with a mean pore size of ~0.2 µm. To further evaluate industrial applicability, the performance of the membranes was tested in the clarification of industrial wastewater, and the membranes showed good recyclability with about 52% flux recovery. The performance of gel-derived membranes thus demonstrates the recycling of waste polymer gels for improving the sustainability of membrane fabrication processes.

In Situ Incorporation of TiO2@Graphene Oxide (GO) Nanosheets in Polyacrylonitrile (PAN)-Based Membranes Matrix for Ultrafast Protein Separation

Organic polymeric ultrafiltration (UF) membranes have been widely used in protein separation due to their advantages of high flux and simple manufacturing process. However, due to the hydrophobic nature of the polymer, pure polymeric UF membranes need to be modified or hybrid to increase their flux and anti-fouling performance. In this work, tetrabutyl titanate (TBT) and graphene oxide (GO) were simultaneously added to the polyacrylonitrile (PAN) casting solution to prepare a TiO₂@GO/PAN hybrid ultrafiltration membrane using a non-solvent induced phase separation (NIPS). During the phase separation process, TBT underwent a sol-gel reaction to generate hydrophilic TiO₂ nanoparticles in situ. Some of the generated TiO₂ nanoparticles reacted with the GO through a chelation interaction to form TiO₂@GO nanocomposites. The resulting TiO₂@GO nanocomposites had higher hydrophilicity than the GO. They could selectively segregate towards the membrane surface and pore walls through the solvent and non-solvent exchange during the NIPS, significantly improving the membrane's hydrophilicity. The remaining TiO₂ nanoparticles were segregated from the membrane matrix to increase the membrane's porosity. Furthermore, the interaction between the GO and TiO₂ also restricted the excessive segregation of the TiO₂ nanoparticles and reduced their losing. The resulting TiO₂@GO/PAN membrane had a water flux of 1487.6 L·m^-2·h^-1 and a bovine serum albumin (BSA) rejection rate of 99.5%, which were much higher than those of the currently available UF membranes. It also exhibited excellent anti-protein fouling performance. Therefore, the prepared TiO₂@GO/PAN membrane has important practical applications in the field of protein separation.

Phase Equilibria and Structure Formation in the Polylactic-co-Glycolic Acid/Tetraglycol/Water Ternary System

This paper concerns a detailed study of the phase separation and structure formation processes that occur in solutions of highly hydrophobic polylactic-co-glycolic acid (PLGA) in highly hydrophilic tetraglycol (TG) upon their contact with aqueous media. In the present work, cloud point methodology, high-speed video recording, differential scanning calorimetry, and both optical and scanning electron microscopy were used to analyze the behavior of PLGA/TG mixtures differing in composition when they are immersed in water (the so-called "harsh" antisolvent) or in a nonsolvent consisting of equal amounts of water and TG (a "soft" antisolvent). The phase diagram of the ternary PLGA/TG/water system was designed and constructed for the first time. The PLGA/TG mixture composition with which the polymer undergoes glass transition at room temperature was determined. Our data enabled us to analyze in detail the structure evolution process taking place in various mixtures upon their immersion in "harsh" and "soft" antisolvent baths and gain an insight into the peculiarities of the structure formation mechanism active in the course of antisolvent-induced phase separation in PLGA/TG/water mixtures. This provides intriguing opportunities for the controlled fabrication of a wide variety of bioresorbable structures-from polyester microparticles, fibers, and membranes to scaffolds for tissue engineering.

Highly stretchable porous regenerated silk fibroin film for enhanced wound healing

Silk fibroin (SF) has received interest in tissue engineering owing to its biocompatibility, biodegradability, and favorable mechanical properties. However, the complex preparation, brittleness, and lack of pores in the structure of the silk fibroin film limit its application. Herein, we show that facile dissolution of SF in aqueous phosphoric acid followed by regeneration in aqueous ammonium sulfate ((NH₄)₂SO₄) could afford highly stretchable films with nano-pores formed in the nonsolvent-induced phase separation process. The named phase separation, which determines the morphology and mechanical properties of the regeneration silk fibroin (RSF) films, is highly dependent on the (NH₄)₂SO₄ concentration as well as the initial concentration of the SF solution. Therefore, the RSF films exhibit a tunable pore size ranging from 230 to 510 nm and excellent stretchability with tensile strain up to 143 ± 16%. Most interestingly, the RSF films were shown to support the proliferation of human skin fibroblasts in vitro as well as speed up full-thickness skin wound healing in a rat model. This work establishes an easy and feasible method to access porous RSF membranes that can be used for wound dressing in clinical settings.

Construction of self-healing polyethersulfone ultrafiltration membrane by cucurbit[8]uril hydrogel via RTIPS method and host-guest chemistry

In this work, the self-healing polyethersulfone ultrafiltration membrane constructed by host-guest chemistry between cucurbit [8]uril (CB [8] is a family of macrocyclic compounds comprising 8 glycoluril units) and two guest molecules based on reverse thermally induced phase separation (RTIPS) method was developed, which had excellent self-healing performance, better mechanical properties, and high permeation flux and BSA rejection rate. The membrane autonomously restored it BSA rejection rate up to about 89% from rejection rate levels as low as 21% after damage. The observed self-healing performance were attributed to the swelling of pore-filled CB [8] hydrogel into the damage position, the molecular interdiffusion of the hydrogel chains, the strong hydrogen bond of the hydrogel chains and the host-guest interaction between CB [8] and two guest molecules (HEC-Np and PVA-MV). SEM morphologies illustrated that the prepared pore-filled membrane via the RTIPS method had homogeneous and porous skin surface and sponge-like cross-section, which imparted the prepared membranes with improved permeability and better mechanical properties. Properties of MR-CB [8] membranes, which varied with increased content of CB [8], were evaluated by permeability, water contact angle, thermogravimetric analysis (TGA), mechanical properties, FRR, scanning electron microscope (SEM) and atomic force microscopy (AFM). The contact angle water showed that CB [8] hydrogel enhanced the surface hydrophilicity of the prepared membrane. TGA illustrated that the thermal stability improved with the increased content of CB [8]. The optimal pore-filled CB [8] hydrogel membrane (MR-CB [8]₂) exhibited that the pure water flux reached 2100.5 L/m² h, while the BSA rejection rate remained at 86.0%. The results of this work suggested pore-filled CB [8] hydrogel membrane was a more promising way to develop polyethersulfone ultrafiltration membranes with self-healing performance.

Current State-of-the-Art in Membrane Formation from Ultra-High Molecular Weight Polyethylene

One of the materials that attracts attention as a potential material for membrane formation is ultrahigh molecular weight polyethylene (UHMWPE). One potential material for membrane formation is ultrahigh molecular weight polyethylene (UHMWPE). The present review summarizes the results of studies carried out over the last 30 years in the field of preparation, modification and structure and property control of membranes made from ultrahigh molecular weight polyethylene. The review also presents a classification of the methods of membrane formation from this polymer and analyzes the conventional (based on the analysis of incomplete phase diagrams) and alternative (based on the analysis of phase diagrams supplemented by a boundary line reflecting the polymer swelling degree dependence on temperature) physicochemical concepts of the thermally induced phase separation (TIPS) method used to prepare UHMWPE membranes. It also considers the main ways to control the structure and properties of UHMWPE membranes obtained by TIPS and the original variations of this method. This review discusses the current challenges in UHMWPE membrane formation, such as the preparation of a homogeneous solution and membrane shrinkage. Finally, the article speculates about the modification and application of UHMWPE membranes and further development prospects. Thus, this paper summarizes the achievements in all aspects of UHMWPE membrane studies.

Supported Imidazolium-Based Ionic Liquids on a Polysulfone Matrix for Enhanced CO2 Capture

The present work demonstrates the potential for improved CO₂ capture capabilities of ionic liquids (ILs) by supporting them on a polysulfone polymeric matrix. CO₂ is one of the main gases responsible for the greenhouse effect and is a focus of The European Commission, which committed to diminishing its emission to 55% by 2023. Various ILs based on combinations of 1-butyl-3-methyl- imidazolium cations and different anions (BMI·X) were synthesized and supported on a polysulfone porous membrane. The influence of the membrane structure and the nature of ILs on the CO₂ capture abilities were investigated. It was found that the membrane's internal morphology and its surface characteristics influence its ILs sorption capacity and CO₂ solubility. In most of the studied configurations, supporting ILs on porous structures increased their contact surface and gas adsorption compared to the bulk ILs. The phenomenon was strongly pronounced in the case of ILs of high viscosity, where supporting them on porous structures resulted in a CO₂ solubility value increase of 10×. Finally, the highest CO₂ solubility value (0.24 mol_CO2/mol_IL) was obtained with membranes bearing supported ILs containing dicarboxylate anion (BMI.MAL).

A review on fabrication, characterization of membrane and the influence of various parameters on contaminant separation process

In most developing countries, the availability of drinking water is a major problem. This creates the need for treatment of wastewater, reusability of water, etc. The membrane technology has its place in the market for treating such water. This review compares polymeric membrane fabrication techniques, characteristics, and factors responsible for effective membrane separation for different materials. Although extensive knowledge is available on membrane fabrication, fabricating a membrane is still more challenging, which is more prone to antifouling properties. The competency in different fabrication methods like phase inversion, interfacial polymerization, stretching, track etching and electrospinning are elucidated in the current study. Further, the challenges and adaptability of different application fabrication methods are studied. Important surface parameters like surface wettability, roughness, surface tension, pore size, surface charge, surface functional group and pure water flux are analyzed for different polymeric membranes. In addition, the properties responsible for fouling the membrane are also covered in detail. Flow direction and velocity are the main factors that characterize a membrane's antifouling nature. Antifouling separation can still be achieved by characterizing feed properties such as pH, temperature, diffusivity, ion concentration, and surface content. Understanding fouling properties is a key to progress in membrane technology to develop an effective membrane separation.

Effect of Acetone as Co-Solvent on Fabrication of Polyacrylonitrile Ultrafiltration Membranes by Non-Solvent Induced Phase Separation

For the first time, the presence of acetone in the casting solutions of polyacrylonitrile (PAN) in dimethylsulfoxide or N-methyl-2-pyrrolidone was studied with regards to thermodynamical aspects of phase separation of polymeric solutions induced by contact with non-solvent (water), formation and performance of porous membranes of ultrafiltration range. The positions of the liquid equilibrium binodals on the phase diagrams of these three-component and pseudo-three-component mixtures were determined. For PAN-N-methyl-2-pyrrolidone-water glass transition curve on a ternary phase diagram was plotted experimentally for the first time. The real-time evolution of the structure of mixtures of PAN with solvents (co-solvents) upon contact with a non-solvent (water) has been studied. The thermodynamic analysis of the phase diagrams of these mixtures, together with optical data, made it possible to propose a mechanism of structure formation during non-solvent induced phase separation of different mixtures. The addition of acetone promotes the formation of a spongy layer on the membrane surface, which decreases the probability of defect formation on the membrane surface and keeps finger-like macrovoids from the underlying layers of the membrane. It was shown that the molecular weight cut-off (MWCO) of the membranes can be improved from 58 down to 1.8 kg/mol by changing the acetone content, while polymer concentration remained the same.

Hollow Fiber Membrane for Organic Solvent Nanofiltration: A Mini Review

Organic solvents take up 80% of the total chemicals used in pharmaceutical and related industries, while their reuse rate is less than 50%. Traditional solvent treatment methods such as distillation and evaporation have many disadvantages such as high cost, environmental unfriendliness, and difficulty in recovering heat-sensitive, high-value molecules. Organic solvent nanofiltration (OSN) has been a prevalent research topic for the separation and purification of organic solvent systems since the beginning of this century with the benefits of no-phase change, high operational flexibility, low cost, as well as environmental friendliness. Especially, hollow fiber (HF) OSN membranes have gained a lot of attention due to their high packing density and easy scale-up as compared with flat-sheet OSN membranes. This paper critically reviewed the recent research progress in the preparation of HF OSN membranes with high performance, including different materials, preparation methods, and modification treatments. This paper also predicts the future direction of HF OSN membrane development.

Preparation of composite polyethersulfone membrane containing basalt powder and optimization of the parameters using response surface methodology

In this study, environmental-friendly composite polyethersulfone (PES) membranes based on basalt powder were prepared by phase inversion method. The effects of polymer percentage, the basalt percentage, and the thickness of the membrane were investigated on the distilled water flux, compaction factor, bovine serum albumin (BSA) rejection, contact angle, fouling factor and the parameters were modelled by response surface methodology (RSM). The distilled water flux increased when the basalt was added to the membrane up to 6% percentage of the polymer amount. The blending of basalt also provided resistance against the membrane compaction. The BSA rejection experiments approved the positive effects of basalt on the rejections efficiencies. At higher basalt percentages, the rejection efficiencies increased from 78% at the raw membrane to 99% for the composite membranes had 10% basalt. The adding of basalt to the membranes decreased the contact angles. The hydrophilicity of the membranes contained basalt in their structures was higher than those which had not basalt. By comparison with the neat membranes and the basalt added membrane, it can be said that the basalt increased the flux recovery and decreased the irreversible fouling factors. The basalt increased the antifouling properties for the composite membranes. Finally, the prepared membranes were characterized by scanning electron microscopy (SEM) and energy dispersive X-ray analysis (EDX).

Effect of ionic liquid on formation of copolyimide ultrafiltration membranes with improved rejection of La3

Ultrafiltration (UF) as a widely used industrial separation method with optimal selection of membrane materials can be applied to extract rare earth metals from dilute solutions formed during the processing of electronic waste by hydrometallurgical methods. In the present work, promising UF copolyimide membranes were prepared using [hmim][TCB] ionic liquid (IL) co-solvent which can be considered as an environmentally friendly alternative to conventional solvents. The membranes were characterized by ATR-FTIR, TGA, SEM and quantum chemical calculations. A significant difference in morphology of these membranes was revealed by SEM of membrane cross-sections; the P84 membrane has finger-like structure of porous substrate in contrast to spongy structure of substrate for the P84/IL membrane due to a higher dynamic viscosity of the casting solution. The transport parameters were determined in ultrafiltration tests with pure water and an aqueous solution of bovine serum albumin. The addition of ionic liquid to the P84 casting solution increases the performance of the membrane. The rejection capacity was evaluated with respect to La³⁺ in the form of a lanthanum alizarin complex (LAC) in aqueous acetone solution. The P84 membrane prepared using IL showed a high rejection (98.5%) with respect to LAC, as well as a significant productivity.

Fabrication of Polyacrylonitrile UF Membranes by VIPS Method with Acetone as Co-Solvent

For the first time, a systematic study was carried out of the replacement of the low-volatility solvents N-methyl-2-pyrrolidone (NMP) or dimethylsulfoxide (DMSO) with the high-volatility solvent acetone in the casting solution of polyacrylonitrile (PAN). The effect of acetone’s presence in the casting solution on the performance of ultrafiltration membranes fabricated via vapor-induced phase separation (VIPS) was investigated. It was possible to replace 40% of NMP and 50% of DMSO with acetone, which resulted in the reduction of the casting solution viscosity from 70.6 down to 41.3 Pa∙s (20% PAN, NMP), and from 68.3 down to 20.6 Pa∙s (20% PAN, DMSO). It was found that 20 min of exposure to water vapor (relative humidity—85%) was sufficient to govern the phase separation, which was mainly induced by the water vapor. Regardless of the casting solution composition (15 or 20% PAN; DMSO or NMP), all membranes formed via VIPS possessed a sponge-like porous structure. The addition of acetone to the casting solution allowed the reduction of the transport pore size from 35–48 down to 8.5–25.6, depending on the casting solution composition. By varying the acetone content at constant polymer concentration, it was possible to decrease the molecular weight cut-off (MWCO) from 69 to 10 kg/mol. Membranes prepared from 20% PAN solution in an acetone/DMSO mixture had the lowest MWCO of 10 kg/mol with a water permeance of 5.1 L/(m²·h·bar).

2D Polymer Nanonets: Controllable Constructions and Functional Applications

Two-dimensional (2D) polymer nanonets have demonstrated great potential in various application fields due to their integrated advantages of ultrafine diameter, small pore size, high porosity, excellent interconnectivity, and large specific surface area. Here, a comprehensive overview of the controlled constructions of the polymer nanonets derived from electrospinning/netting, direct electronetting, self-assembly of cellulose nanofibers, and nonsolvent-induced phase separation is provided. Then, the widely researched multifunctional applications of polymer nanonets in filtration, sensor, tissue engineering, and electricity are also given. Finally, the challenges and possible directions for further developing the polymer nanonets are also intensively highlighted. This article is protected by copyright. All rights reserved.