High-performance removal of diazinon pesticide from water using multi-walled carbon nanotubes

Adsorptive removal of organophosphate pesticides from aqueous solution using electrospun carbon nanofibers

Organophosphate pesticides (OPPs) are widely prevalent in the environment primarily due to their low cost and extensive use in agricultural lands. However, it is estimated that only about 5% of these applied pesticides reach their intended target organisms. The remaining 95% residue linger in the environment as contaminants, posing significant ecological and health risks. This underscores the need for materials capable of effectively removing, recovering, and recycling these contaminants through adsorption processes. In this research, adsorbent materials composed of electro-spun carbon nanofibers (ECNFs) derived from polyacrylonitrile was developed. The materials were characterized through several techniques, including scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Fourier Transform Infrared Spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) analysis, and contact angle measurements. SEM analysis revealed details of the structural properties and inter-fiber spacing variations of the carbon nanofibers. The results revealed that ECNFs possess remarkable uniformity, active surface areas, and high efficiency for adsorption processes. The adsorption studies were conducted using batch experiments with ethion pesticide in aqueous solution. High-Performance Liquid Chromatography-Diode Array Detector (HPLC-DAD) was utilized to quantify the concentrations of the OPP. Various parameters, including adsorbent dosage, pH, contact time, and initial ethion concentration, were investigated to understand their impact on the adsorption process. The adsorption isotherm was best described by the Freundlich model, while the kinetics of adsorption followed a non-integer-order kinetics model. The adsorption capacity of the ECNFs for OPP removal highlights a significant advancement in materials designed for environmental remediation applications. This study demonstrates the potential of ECNFs to serve as effective adsorbents, contributing to the mitigation of pesticide contamination in agricultural environments.

Magnetic carboxymethyl gond katira-grafted-poly(3-aminobenzoic acid) as an antibacterial biosorbent for purification of acetamiprid-contaminated water

The elimination of pesticides from polluted water is critical due to their harmful environmental and biological impacts. Recently, there has been interest in utilizing natural polymer-based adsorbents as an eco-friendly approach to eliminate or reduce the levels of water pollutants. In this work, we synthesized an antimicrobial and magnetic bionanocomposite consisting of carboxymethyl gond katira-grafted- poly(3-aminobenzoic acid) with iron oxide and zinc oxide NPs (CMT-g-P3ABA/ZnO/Fe3O4) through an in situ polymerization reaction and examined for its ability to adsorb the pesticide acetamiprid (AP). The bionanocomposite was characterized using several analytical techniques, including spectroscopy; XRD presented the crystalline structure of ZnO/Fe3O4 in the CMT-g-P3ABA amorphous matrix. The ZnO/Fe3O4 partially aggregated formation and exhibited polyhedral crystal shapes was depicted by electron microscopy images, vibrating sample magnetometer (45.06 emu/g), porosimetry (5.52 m2/g), and thermal (Chair yield of approximately 43.83 %) and elemental analyses. Under various conditions, including solution pH (4-9), adsorbent dosage (0.005-0.025 g), time of contact (10-30 min), and pesticide preliminary concentration (200-400 mg/L) in 10 mL of the solution. Based on this research, Adsorption data were perfectly fitted by the Freundlich isotherm model with RAP2= 0.99038, while the pseudo-second-order (PSO) model well-explained adsorption kinetics with RAP2= 0.99847. AP adsorption to the CMT-g-P3ABA/ZnO/Fe3O4 bionanocomposite was successful due to hydrophobic interactions, hydrogen bonding, and π-π stacking. Furthermore, adsorption-desorption experiments demonstrated that the bionanocomposite could be regenerated after three reuse cycles without considerable loss of pesticide removal performance. The bionanocomposite also exhibited promising antimicrobial activity in contradiction to test bacteria.

Innovations and challenges in adsorption-based wastewater remediation: A comprehensive review

Water contamination is an escalating emergency confronting communities worldwide. While traditional adsorbents have laid the groundwork for effective water purification, their selectivity, capacity, and sustainability limitations have driven the search for more advanced solutions. Despite many technological advancements, economic, environmental, and regulatory hurdles challenge the practical application of advanced adsorption techniques in large-scale water treatment. Integrating nanotechnology, advanced material fabrication techniques, and data-driven design enabled by artificial intelligence (AI) and machine learning (ML) have led to a new generation of optimized, high-performance adsorbents. These advanced materials leverage properties like high surface area, tailored pore structures, and functionalized surfaces to capture diverse water contaminants efficiently. With a focus on sustainability and effectiveness, this review highlights the transformative potential of these advanced materials in setting new benchmarks for water purification technologies. This article delivers an in-depth exploration of the current landscape and future directions of adsorbent technology for water remediation, advocating for a multidisciplinary approach to overcome existing barriers in large-scale water treatment applications.

Comprehensive investigation of isotherm, RSM, and ANN modeling of CO2 capture by multi-walled carbon nanotube

Chemical vapor deposition was used to produce multi-walled carbon nanotubes (MWCNTs), which were modified by Fe-Ni/AC catalysts to enhance CO2 adsorption. In this study, a new realm of possibilities and potential advancements in CO2 capture technology is unveiled through the unique combination of cutting-edge modeling techniques and utilization of the recently synthesized Fe-Ni/AC catalyst adsorbent. SEM, BET, and FTIR were used to analyze their structure and morphology. The surface area of MWCNT was found to be 240 m2/g, but after modification, it was reduced to 11 m2/g. The modified MWCNT showed increased adsorption capacity with higher pressure and lower temperature, due to the introduction of new adsorption sites and favorable interactions at lower temperatures. At 25 °C and 10 bar, it reached a maximum adsorption capacity of 424.08 mg/g. The optimal values of the pressure, time, and temperature parameters were achieved at 7 bar, 2646 S and 313 K. The Freundlich and Hill models had the highest correlation with the experimental data. The Second-Order and Fractional Order kinetic models fit the adsorption results well. The adsorption process was found to be exothermic and spontaneous. The modified MWCNT has the potential for efficient gas adsorption in fields like gas storage or separation. The regenerated M-MWCNT adsorbent demonstrated the ability to be reused multiple times for the CO2 adsorption process, as evidenced by the study. In this study, a feed-forward MLP artificial neural network model was created using a back-propagation training approach to predict CO2 adsorption. The most suitable and efficient MLP network structure, selected for optimization, consisted of two hidden layers with 25 and 10 neurons, respectively. This network was trained using the Levenberg-Marquardt backpropagation algorithm. An MLP artificial neural network model was created, with a minimum MSE performance of 0.0004247 and an R2 value of 0.99904, indicating its accuracy. The experiment also utilized the blank spreadsheet design within the framework of response surface methodology to predict CO2 adsorption. The proximity between the Predicted R2 value of 0.8899 and the Adjusted R2 value of 0.9016, with a difference of less than 0.2, indicates a high level of similarity. This suggests that the model is exceptionally reliable in its ability to predict future observations, highlighting its robustness.

Study on diazinon toxicity reduction by electro-Fenton process: A bioassay using daphnia magna

The realm of diazinon reduction from polluted water has witnessed a surge in the significance of advanced oxidation processes (AOPs) in recent times. However, there is a dearth of research focusing on the mitigation of its toxicity through AOPs. Thus, the primary objective of this study was to evaluate the effectiveness of the Electro-Fenton process (EFP) in the eradication and detoxification of diazinon in aqueous solutions. Synthetic wastewater samples with concentrations of 2, 2.5 and 3 mg/L were prepared. A total of 27 samples were determined using Box Behnken Design. Reaction time, pH and iron to hydrogen peroxide ratio (Fe2+/H2O2) were examined as operational parameters under a constant current of 5.4 amps. The quantification of diazinon concentration was performed using High-Performance Liquid Chromatography (HPLC). To evaluate the detoxification of diazinon, the Daphnia magna bioassay was employed as a methodology in this study. According to the results, the EFP could reduce the diazinon to zero and the LC50 values are increased by applying the process. The LC50 values for diazinon were determined using the Daphnia magna bioassay, considering initial concentrations of 2, 2.5, and 3 mg/L at a pH of 5, a reaction time of 15 min, and an iron to hydrogen peroxide molar ratio of 2. The recorded LC50 values were 3.039, 3.076, and 3.106, respectively, indicating the lowest frequency of cumulative death in Daphnia magna. In this case, after 96 h, only 3 cases (30%) of Daphnia magna death were observed. However, for all the mentioned concentrations of diazinon, after 96 h of exposure to samples without applying the Daphnia Magna death process, it was observed between 60 and 100%. Reducing the diazinon concentration and increasing the 96-h LC50 showed that the EFP can reduce the toxicity of diazinon on Daphnia Magna at the same time. Therefore, EFP can be considered a superior method with low ecotoxicity.

Preparation of novel and recyclable chitosan-alumina nanocomposite as superabsorbent to remove diazinon and tetracycline contaminants from aqueous solution

This work presents a novel, strong and efficient adsorbent (CS@TDI@EDTA@γ-AlO(OH)) prepared through the green process using three components, chitosan, BNPs and EDTA using amide and ester bridges. An eco-friendly and easy approach was used for the preparation of this novel adsorbent, the low cost, easy access to the used materials, and the simplicity of the preparation method are some of the interesting advantages of this work. Also, this prepared adsorbent was used as an adsorbent to remove diazinon organophosphate poison and tetracycline antibiotic from aqueous solutions. In order to confirm the prepared adsorbent structure, the CS@TDI@EDTA@γ-AlO(OH) composite was investigated by various analyses including FT-IR, EDX, XRD, FESEM and TGA. The adsorption behavior of the adsorbent prepared for the removal of tetracycline and diazinon was investigated under different conditions by varying the concentration, temperature, the adsorbent dose, pH and contact time. Based on various tests, the highest diazinon adsorption capacity was obtained for 0.12 g/L adsorbent at pH 7 and 60 °C with 40 mg/L initial concentration. Also, the maximum adsorption capacity of the tetracycline was obtained for 0.12 g/L adsorbent at pH 9 and 60 °C with 30 mg/L initial concentration. The equilibrium results for diazinon and for tetracycline were in good accordance with the Langmuir and Freundlich isotherm models, respectively. Also, the highest adsorption capacities for diazinon at pH 7 and tetracycline at pH 9 were 1428.5 and 555.5 mg/g, respectively. Also the kinetic investigations revealed that the correlation factor (R2) of pseudo-second-order model obtained for the adsorption of diazinon and tetracycline was 0.9986 and 0.9988, while the coefficient k (g/mg.min) was 0.000084 and 0.0033, respectively. These results indicate that the adsorption of diazinon and tetracycline is pseudo-second-order kinetics model. Formation of hydrogen bonds between adsorbate and adsorbent as well as the high specific surface area and porosity of the adsorbent are the main mechanisms that contribute to the adsorption process. In addition, thermodynamic studies indicated that the adsorption of diazinon and tetracycline is a spontaneous endothermic process. The adsorbent prepared in this work was expected to have wide range of applications in wastewater treatment thanks to its good reusability in water and strong removal of diazinon and tetracycline compared to other adsorbents.

Photocatalytic removal of organophosphorus pesticide by the WO3-Fe3O4/rGO photocatalyst under visible light

The WO3-Fe3O4/reduced graphene oxide (rGO) composite was synthesized with a hydrothermal method for the photocatalytic removal of diazinon (DZ) in visible light. The influence of catalyst concentration (0.5-1.5 g L-1), pH (5-9), and initial pollutant value (5-15 mg L-1) on the pesticide degradation was studied. The performance of the WO3-Fe3O4/rGO nanocomposite for DZ degradation under visible light shows 94% degradation of 5 mg L-1 DZ for 100 min with 1 g L-1 nanocomposite, and the degradation kinetic was modeled in pseudo-first order (PFO) and the maximum kobs was 0.0248 min-1. The photocatalytic mechanism and the intermediates of DZ degradation were identified. In addition, the WO3-Fe3O4/rGO catalyst showed reusability after 4 runs. The results of this work illustrate that the WO3-Fe3O4/rGO nanocomposite can be applied for real use owing to its high catalytic performance.

Pesticides residues determination and probabilistic health risk assessment in the soil and cantaloupe by Monte Carlo simulation: A case study in Kashan and Aran-Bidgol, Iran

Cantaloupe is a popular agricultural product in the hot season of Iran. On the other hand, the frequent use of pesticides in cantaloupe fields is the most important threat to the health of farmers and consumers. Therefore, the present study aims to measure the concentration of diazinon (DZN), chlorpyrifos (CPF), and malathion (MLT) in cantaloupe cultivated in Kashan and Aran-Bidgol (Iran) and to estimate the possible oral and dermal risk of these pesticides by Monte Carlo simulation (MCS). 36 cantaloupe samples, 18 samples before, and 18 samples after the latent period were collected from different places of cantaloupe cultivation from April to May 2021. After measuring the pesticides using the QuEChERS approach, oral and dermal risk assessments were calculated.The mean and standard deviation of the concentrations of chlorpyrifos, malathion, and diazinon in 18 cantaloupe samples, after the latent period, were (30.39 ± 13.85), (18.361 ± 1.8), and (21.97 ± 0.86) μg kg-1, respectively. Concentration of Malathion, diazinon, and Chlorpyrifos in the soil were 0.22, 0.25, and 0.3 mg kg-1, respectively, and pesticide cumulative risk assessment in soil was obtained 0.011 for Malathion, 0.05 for diazinon and 0.03 for Chlorpyrifos. Target Hazard Quotient (THQ) according to the cantaloupe consumption and dermal exposure in children and adults, was safe range. Although non-cancerous dermal and oral risk of cantaloupe is low, constant exposure can be harmful. Therefore, the findings of this study play an important role in increasing the understanding of the negative health consequences of pesticide contamination in cantaloupe for consumers, especially local residents, and can help by adopting remedial strategies to reduce environmental concerns.

Visible light-driven ZnO/Fe3O4 magnetic nanoparticles for detoxification of diazinon: the photocatalytic optimization process with RSM-BBD model

Today, diazinon is one of the most widely used organophosphorus pesticides, whose widespread use can cause many ecological and biological risks. In this research, a magnetic ZnO/Fe3O4 nanoparticle was used to investigate the photocatalytic degradation of diazinon. Sol-gel synthesis was used to create the nanoparticle, which was then characterized using XRD, FTIR, FESEM, VSM, and XPS techniques. The design of photocatalytic degradation experiments was done using the response surface method and the Box-Behnken design model. The investigated parameters include pH, nanoparticle concentration, diazinon concentration, and irradiation time. The characterization of the ZnO/Fe3O4 nanoparticle showed well-formed crystalline phases and a cubic spinel structure. Additionally, the shape of the nanoparticle is almost uniform and spherical. The FT-IR spectrum also confirmed the presence of all functional groups related to ZnO and Fe3O4 in the ZnO/Fe3O4 nanoparticles structure. The synthesized nanocomposite has superparamagnetic properties and a very small coercive field, making it easily recyclable, according to a VSM analysis. XPS results also showed the presence of Fe (Fe 2p1/2 and Fe 2p3/2), Zn (Zn 2p1/2 and Zn 2p3/2), oxygen (O1s), and weak carbon (C1s) peaks in the ZnO/Fe3O4 structure. The results of the photocatalytic optimization experiments showed that the highest efficiency of diazinon toxin degradation is 99.3% under the conditions of pH 7, diazinon initial concentration of 10 mg/L, nanoparticle concentration of 1 g/L, and a contact time of 90 min. This result is very close to the BBD model's predicted removal efficiency under optimal conditions (100%). As a result, the ZnO/Fe3O4 nanocomposite can produce active free radicals through UV radiation, and these radicals can successfully remove diazinon under actual conditions.

Investigation of the performance of activated carbon cloth to remove glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos from aqueous solutions by adsorption/electrosorption

The present study investigates the removal of glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos herbicides from their 5 × 10^-5 M aqueous solutions onto activated carbon cloth by adsorption and electrosorption. Analysis of these highly polar herbicides was achieved by UV-visible absorbance measurements, after derivatization with 9-fluorenylmethyloxycarbonyl chloride. The limit of quantification values of glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos were 1.06 × 10^-6 mol L^-1, 1.38 × 10^-6 mol L^-1, 1.32 × 10^-6 mol L^-1 and 1.08 × 10^-6 mol L^-1, respectively. Glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos were removed from their aqueous solutions with higher efficiencies by means of electrosorption (78.2%, 94.9%, 82.3% and 97%, respectively) than of open-circuit adsorption (42.5%, 22%, 6.9% and 81.8%, respectively). Experimental kinetic data were fitted to pseudo-first order and pseudo-second order kinetic models. It was determined that pseudo-second order kinetic model represents experimental data better with satisfactory coefficient of determination, r² (> 0.985) and normalized percent deviation, P (< 5.15) values. Adsorption isotherm data were treated according to Freundlich and Langmuir isotherm models. Based on the r² (> 0.98) and P (< 5.9) values, it was found that experimental data well fitted to Freundlich isotherm model. Adsorption capacities of activated carbon cloth for glyphosate, glufosinate, aminomethylphosphonic acid and bialaphos, expressed in terms of Freundlich constant, were calculated as 20.31, 118.73, 239.33 and 30.68 mmol g^-1, respectively. The results show that the studied ACC can be used in home/business water treatment systems as an adsorbent due to its high adsorption capacity.

Global distribution of pesticides in freshwater resources and their remediation approaches

The role of pesticides in enhancing global agricultural production is magnificent. However, their unmanaged use threatens water resources and individual health. A significant pesticide concentration leaches to groundwater or reaches surface waters through runoff. Water contaminated with pesticides may cause acute or chronic toxicity to impacted populations and exert adverse environmental effects. It necessitates the monitoring and removing pesticides from water resources as prime global concerns. This work reviewed the global occurrences of pesticides in potable water and discussed the conventional and advanced technologies for the removal of pesticides. The concentration of pesticides highly varies in freshwater resources across the globe. The highest concentration of α-HCH (6.538 μg/L, at Yucatan, Mexico), lindane (6.08 μg/L at Chilka lake, Odisha, India), 2,4, DDT (0.90 μg/L, at Akkar, Lebanon), chlorpyrifos (9.1 μg/L, at Kota, Rajasthan, India), malathion (5.3 μg/L, at Kota, Rajasthan, India), atrazine (28.0 μg/L, at Venado Tuerto City, Argentina), endosulfan (0.78 μg/L, at Yavtmal, Maharashtra, India), parathion (4.17 μg/L, at Akkar, Lebanon), endrin (3.48 μg/L, at KwaZuln-Natl Province, South Africa) and imidacloprid (1.53 μg/L, at Son-La province, Vietnam) are reported. Pesticides can be significantly removed through physical, chemical, and biological treatment. Mycoremediation technology has the potential for up to 90% pesticide removal from water resources. Complete removal of the pesticides through a single biological treatment approach such as mycoremediation, phytoremediation, bioremediation, and microbial fuel cells is still a challenging task, however, the integration of two or more biological treatment approaches can attain complete removal of pesticides from water resources. Physical methods along with oxidation methods can be employed for complete removal of pesticides from drinking water.

Molecular modeling investigation on mechanism of diazinon pesticide removal from water by single- and multi-walled carbon nanotubes

In this study, the mechanism of diazinon adsorption on single-walled carbon nanotubes (SWNTs), as well as multi-walled carbon nanotubes (MWNTs), was investigated using molecular modelling. Determination of the lowest energy sites of different types of carbon nanotubes (CNTs) was demonstrated. The adsorption site locator module was used for this purpose. It was found that the 5-walled CNTs are the best MWNTs for diazinon elimination from water due to their higher interactions with diazinon. In addition, the adsorption mechanism in SWNT and MWNTs was determined to be wholly adsorption on the lateral surface. It is because the geometrical size of diazinon molecules is larger than the inner diameter of SWNT and MWNTs. Furthermore, the contribution of diazinon adsorption on the 5-wall MWNTs was the highest, for the lowest diazinon concentration in the mixture.

Design and development of novel magnetic Lentinan/PVA nanocomposite for removal of diazinon, malathion, and diclofenac contaminants

Increasing population growth and rapid expansion of the industrialization of the world society have caused severe environmental pollution to the planet. This study was carried out in order to investigate the synthesis of biopolymeric texture nano adsorbent based on the Lentinan (LENT), Poly Vinyl Alcohol (PVA) and Iron Oxide nanoparticles for the removal of environmental pollutants. The spherical structural morphology of Fe₃O₄@LENT/PVA nanocomposite has been determined by FE-SEM analyses. According to the obtained results from FTIR analyses, all absorption bands of the Fe₃O₄, LENT, and PVA, had been existed in nanocomposite and approved the successful formation of it. From EDS analysis, it has been revealed that 57.21 wt% Fe, 17.56 wt% C and 25.23 wt% O. Also, the XRD pattern of the nanocomposite, approved the presence of polymeric and magnetic parts with card no. JCPDS, 01-075-0033. The BET analysis has defined specific surface area (47 m²/g) and total pore volume (0.15 cm³/g). Moreover, high heterogeneity and structural stability of the fabricated Fe₃O₄@LENT/PVA nanocomposite have been proven by TGA. Besides, VSM analysis measured great magnetic property of the nanocomposite (48 emu/g). Also, the Fe₃O₄@LENT/PVA nanocomposite potential for effective removal of malathion (MA), Diazinon (DA), and Diclofenac (DF) from watery solution has studied by an experiment based on the efficacy of adsorbent dosage, pH, and temperature. The adsorption kinetics of three pollutants had investigated using pseudo-first-order (PFO), pseudo-second-order (PSO) and intra-particle diffusion (IPD) velocity equations, the results showed that the kinetics followed PSO velocity equations. Also, the Langmuir, Freundlich, Dubbin-Radushkevich (D-R) and Temkin isotherm models had investigated, and the adsorption isotherm was adopted from the Langmuir model. The results demonstrated that in the presence of Fe₃O₄@LENT/PVA nanocomposite, at the optimal conditions (contact time = 180 min, pH = 5, nanocomposite dosage = 0.20 g/L and temperature of 298 K) the maximum adsorption capacity of MA, DF, and DA were 101.57, 153.28, and 102.75 mg/g, respectively. The antibacterial features of the Fe₃O₄@LENT/PVA nanocomposite, had evaluated by Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) bacteria, but the result did not show any antibacterial activity.

Utilizing modified cellulose nanoparticles derived from a plant loofah sponge to improve the removal of diazinon insecticide from an aqueous medium

Organophosphate insecticides, such as diazinon, have been well investigated to pose health and environmental risks. In this study, ferric-modified nanocellulose composite (FCN) and nanocellulose particles (CN) based on a natural source as a loofah sponge were synthesized to verify their adsorption potential to eliminate diazinon (DZ) from contaminated water. The as-prepared adsorbents were characterized by performing TGA, XRD, FTIR spectroscopy, SEM, TEM, pHPZC, and BET analyses, in which FCN showed high thermal stability, surface area of 82.65 m2 g-1, surface with mesopores, good crystallinity (61.6%), and particle size of 86.0 nm. The results of adsorption tests demonstrated that the maximum Langmuir adsorption capacity (294.98 mg g-1) was exhibited by FCN at 38 °C, pH 7, 1.0 g L-1 of adsorbent dosage, and 20 h of contact shaking time. The effect of adding KCl solution with high ionic strength (1.0 mol L-1) reduced the DZ removal percent by 52.9%. The experimental adsorption data achieved the best fit with all the applied isotherm models with favorable, physical, and endothermic nature of adsorption consistent with thermodynamic data. Pentanol attained higher desorption efficiency (95%) and was used in five adsorption/desorption cycles in which FCN exhibited only an 8.8% decrease in the removal percent of DZ.

Removal of Penicillin G from aqueous medium by PPI@SBA-15/ZIF-8 super adsorbent: Adsorption isotherm, thermodynamic, and kinetic studies

In the present paper, synthesis of SBA-15 nanoparticles was carried out from tetraethyl orthosilicate (TEOS) precursor using the sol-gel process. After being combined with Poly propylene imine, and ZIF-8 they were employed for the removal of Penicillin G. The synthesized combination morphology was assessed using nitrogen adsorption and desorption (BET), Fourier transform infrared (FTIR) spectroscopy, and X-ray powder diffraction (XRD). The parameters affecting Penicillin G removal, including pH, amount of adsorbent, time of contact, temperature, and concentration, were optimized, and the optimum levels of the mentioned variables were reported to be pH = 3, 0.03 g, 90 min, 25 °C, and 100 ppm, respectively. In addition, application of Freundlich, Langmuir, Dubinin-Radushkevhch, and Tempkin models and pseudo-first-order and pseudo-second-order adsorption synthetic equations aimed at determining the type of adsorbent isotherm. The results showed that the best fitting of Langmuir (R² = 0.9944, q_m = 400 mg/g) for adsorption isotherm and pseudo-second-order model (R² = 0.9905) for kinetics studies. Furthermore, data of Gibbs free energy and enthalpy demonstrated an exothermic and spontaneous process in the research.

Design and modeling of diazinon degradation in hydrous matrix by Ni-doped ZnO nanorods under ultrasonic irradiation: process optimization using RSM (CCD), kinetic study, reaction pathway, mineralization, and toxicity assessment

In first, the Ni-doped ZnO nanorods used as an appeal sonocatalyst was synthesized through co-precipitation method. Afterwards, the crystalline structure, functional groups, surface morphology, and elemental composition were characterized by a set of analysis. Removal of diazinon ((DZ) as a renowned pesticide) was investigated using sonocatalytic performance of US/Ni-doped ZnO system. In this empirical study, response surface methodology (RSM) based central composite design (CCD) was applied for optimization of operational factors. Under the optimum conditions such as initial pH = 5, initial DZ concentration = 15 mg L^-1, sonocatalyst dosage = 1 g L^-1, and in the presence of organic compounds (oxalic acid, humic acid, and folic acid) = 3 mg L^-1, the sonocatalytic degradation of DZ after 15 min was 82.29%. The F-value (6.64) and P-value (< 0.0001) for DZ degradation in the quadratic model imply the proposed model was significant. A-factor (pH) considers as a prominent factor owing to having the highest F-value. In addition, the sonocatalytic data in this study exhibited valid fitting for the first order kinetic model (R² > 0.98). After six consecutive cycles, the Ni-doped ZnO nanorods could be recyclable for sonocatalytic degradation of DZ. The five main compounds produced during the US/Ni-doped ZnO embracing 2-isopropyl-6-methyl-4-pyrimidinol (IMP), diethyl phosphonate, diazoxon, hydroxyldiazinon, and diazinon methyl ketone are formed in the path of DZ degradation. OFAT style also revealed 99.99% of DZ degradation with 73.26% of mineralization rate in optimum status. The Ni-doped ZnO presented agreeable sonocatalytic facility in the refinement of real water and wastewater matrix. Finally, the results of toxicity evaluation (Daphnia magna) in the sonocatalytic degradation of DZ (by US/Ni-doped ZnO system) showed that the toxicity of the DZ solution lessened under US waves (LC₅₀ and TU 48 h equal to 36.472 and 2.741 volume percent, respectively).

Synthesis and application of a carbon composite containing molecularly imprinted poly(methacrylic acid) for efficient removal of fenpyroximate pesticide

This work describes fabrication steps of the carbon composite based on molecular imprinted poly(methacrylic acid) (MIP-CC) as a new adsorbent for the selective removal of fenpiroxymate pesticide (Fen). The prepared composite was characterized using Brunauer-Emmett-Teller (BET), zeta sizer and Field Emission Scanning Electron Microscopy (FESEM) techniques. The influence of operational parameters such as solution pH, contact time, amount MIP for preparation of carbon composite and amount MIP- CC toward removal of Fen have been evaluated and optimized via central composite design (CCD) as an optimization tool of response surface method. The optimum removal (87%) was achieved at pH 6.5, 1.53 g/L carbon composite prepared with 3.4 wt % MIP at 70 min. The maximum adsorption of Fen by the fabricated MIP-CC was 254 mg/g. Compared with the corresponding non-imprinted polymer (NIP-CC), the MIP-CC exhibited higher adsorption capacity and outstanding selectivity toward Fen. Langmuir isotherm best fitted the adsorption equilibrium data of MIP-CC and the kinetics followed a pseudo-second-order model. The calculated thermodynamic parameters showed that adsorption of Fen pesticide was spontaneous and exothermic under the studied conditions.

Emerging Trends in the Remediation of Persistent Organic Pollutants Using Nanomaterials and Related Processes: A Review

Persistent organic pollutants (POPs) have become a major global concern due to their large amount of utilization every year and their calcitrant nature. Due to their continuous utilization and calcitrant nature, it has led to several environmental hazards. The conventional approaches are expensive, less efficient, laborious, time-consuming, and expensive. Therefore, here in this review the authors suggest the shortcomings of conventional techniques by using nanoparticles and nanotechnology. Nanotechnology has shown immense potential for the remediation of such POPs within a short period of time with high efficiency. The present review highlights the use of nanoremediation technologies for the removal of POPs with a special focus on nanocatalysis, nanofiltration, and nanoadsorption processes. Nanoparticles such as clays, zinc oxide, iron oxide, aluminum oxide, and their composites have been used widely for the efficient remediation of POPs. Moreover, filtrations such as nanofiltration and ultrafiltration have also shown interest in the remediation of POPs from wastewater. From several pieces of literature, it has been found that nano-based techniques have shown complete removal of POPs from wastewater in comparison to conventional methods, but the cost is one of the major issues when it comes to nano- and ultrafiltration. Future research in nano-based techniques for POP remediation will solve the cost issue and will make it one of the most widely accepted and available techniques. Nano-based processes provide a sustainable solution to the problem of POPs.

Removal of boron by a modified resin in fixed bed column: Breakthrough curve analysis using dynamic adsorption models and artificial neural network model

Continuous removal of toxic element boron from aqueous solution was investigated with new phenolic hydroxyl modified resin (T-resin) using a fixed bed column reactor operated under various flow rates, bed height and influent concentrations. The breakthrough time, exhaustion time and uptake capacity of the column bed increased with increasing column bed height, whereas decreased with increasing influent flow rate. The breakthrough time and exhaustion time decreased, but uptake capacity increased with increasing influent concentration, and actual uptake capacity was obtained as 6.52 mg/g at a concentration of 7.64 mg/L. The three conventional models of bed depth service time (BDST), Thomas and Yoon-Nelson were used to appropriately predict the whole breakthrough behavior of the column and to estimate the characteristic model parameters for boron removal. However, artificial neural network (ANN) model was more accurate than the conventional models with the least relative error and the highest correlation coefficients. By the relative importance of the operational parameters obtained from ANN model, the sequence is as follows: total effluent time > initial concentration > flow rate > column height. The adsorption capacity of boron was changed between 5.24 and 1.74 mg/g during the five time regeneration. From the life factor calculation, it is suggested that the column bed could avoid the breakthrough time of t = 0 for 6.8 cycles, whereas, the uptake capacity would be zero after 7.8 cycles.

Diazinon pesticide photocatalytic degradation in aqueous matrices based on reductive agent release in iodide exciting under UV Irradiation

Regarding the cost-effective degradation of diazinon (DIZ), the present study was conducted to develop and UV/iodide process in a photo catalyst reactor. CCD modeling applied and the results shows that the highest R-squared value (adjusted R-squared: 0.9987), the lowest P-value (2.842 e - 10), the lowest AIC (14.54), and the most insignificant lack-of-fit (0.73) belonged to the second-order model. Based on second-order model, the stationary points for time, iodide: DIZ (molar ratio %), DIZ concentration, and pH were 6.99 min, 80.15% iodide: DIZ (molar ratio %), 3.34, mg L^-1, and pH 7.34 (- log₁₀[H⁺]), respectively. The maximum reduction efficiency of 97.22% was obtained at the experimental conditions. The LC-MS analyses from optimal condition implied that all the DIZ molecules and its intermediates breaking to simple compounds during 15 min of processing. The data shown UI process reduced the BOD and COD levels by about 66% and 86.29% within 80 min of photoreaction, respectively. Furthermore, in kinetic investigation, with the increase in DIZ concentration, k_obs and r_obs increased and secondly, the conventional and PCBR reactor k_obs increased by about respectively 17% and 50% with an increase in DIZ concentration from 5 to 15 mgL^-1. Additionally, when the DIZ concentration increase from 5 to 15 mg L^-1, r_obs increased in the conventional and PCBR reactors respectively about 4.9 and 6 times. Figure-of-merit E_Eo changed from 12.66-17.41 to 7.26-10.15 kWhm³ for the conventional reactor, and 8.66-13.61 to 5.24-8.12 kWhm³ in PCBR, when the DIZ concentration increasing from 5 to 15 mg L^-1. Consequently, in the PCBR reactor, the energy consumption reduced by 14% at 5 mg L^-1 DIZ concentration and by 60% at 15 mg L^-1 DIZ concentration. Also, total cost of the system (TCS) decreases from 4.52 to 1.46 $ in conventional reactor and 1.47 to 0.42 $ in PCBR reactor when the DIZ concentration increase from 5 to 15 mg L^-1.

Evaluation of alternations in DNA methylation of CYP3A4 gene upstream regulatory elements in gastric cancer and in response to Diazinon treatment

BACKGROUND

Little is known about cytochrome P450 3A4 (CYP3A4) DNA methylation and transcription alterations in gastric cancer.

OBJECTIVE

In this paper, we initially aimed to address the effect of diazinon pesticide on DNA methylation and transcription changes of the CYP3A4 gene in a human gastric cell line. In the next step, we studied the methylation differences of CpG sites within the upstream regulatory regions of the CYP3A4 gene among human gastric cancerous and healthy tissues.

METHODS

For the in vitro assay, the methylation changes of the C/EBP response element and transcript level of the CYP3A4 gene were studied following treatment of the AGS cell line with various concentrations of diazinon pesticide. In the next phase, the methylation percentages of 24 CpG sites within or around the upstream regulatory elements including near promoter, C/EBP binding site, XREM, and CLEM4 in 11 specimens of human gastric cancer tissue were compared to their adjacent healthy tissues.

RESULTS

Treatment with 10 µM Diazinon significantly increased the CYP3A4 gene transcription by approximately 27-fold, which was correlated with the hypermethylation of 3 CpGs in C/EBP binding sites including -5998, -5731 and -5725 (p<0.001 for all comparisons). Results of bisulfite sequencing revealed that the CpG sites which are located in -1521 (p=0.003), -1569 (p=0.027), -10813 (p=0.003), -10851 (p=0.001) and -10895 (p=0.0) bp from transcription start site, were significantly hypermethylated in cancerous tissues comparing to their healthy cohort.

CONCLUSION

Hypermethylation of CLEM4 and a region near the core promoter may have a significant association with gastric cancer incidence.

Evaluation of sulfuric acid-pretreated biomass-derived biochar characteristics and its diazinon adsorption mechanism

In this study, hemicellulose was mostly removed from biomass (larch and oak) using a sulfuric acid pretreatment. Biochar was then prepared from raw and pretreated biomass using a carbonization process. Biochar derived from pretreated biomass had an aromatic and graphitized structure, and functional groups were observed on the surface. The specific surface area was higher for biochar obtained from pretreated biomass than biochar derived from raw biomass. The biochar obtained from pretreated biomass contained a greater number of micropores than biochar derived from raw biomass. The diazinon removal rate was the highest for biochar that was obtained from pretreated biomass when 10% of the biochar was added to the soil. As a result of the adsorption of diazinon onto the biochar obtained from pretreated biomass, the R² value of the Langmuir isotherm was higher than that of the Freundlich's R².

Synthesis of new composite based on TiO2 immobilized in glass fibers for photo-catalytic degradation of chlorobenzene in aqueous solutions

In this study photo-catalytic degradation of chlorobenzene from aqueous solutions using CQD decorated Fe-doped TiO₂ immobilized in Glass Fibers (GF) was investigated. Characteristics of the synthesized photo-catalyst were determined by EF-SEM, EDX, BET, XRD, FTIR, and DRS analysis. Additionally, DRS analysis demonstrated adding CQD to the TiO₂-Fe reduced its band gap energy from 2.96 eV to 2.91eV, while that was 3.10 eV for undoped TiO₂. Among that three photo-catalysts, GF/CQD_(4.5 wt%) decorated Fe-TiO₂ composite had performance nearly 100.0%, when pH was 5 and low concentration of chlorobenzene. In addition, GF/CQD_(4.5 wt%) decorated Fe-TiO₂ composite show it could be well applied for five times and with a little reduction on the performance. Also, no detectable Fe found to be released from the composite. Minimum inhibitory concentration (MIC) for E. coli bacteria was 12.2 mg L^-1 of chlorobenzene residual. Our findings show the catalyst was successful for chlorobenzene removal in the wastewater effluent. In conclusion, present hybrid composite could successfully and safely remove chlorobenzene from synthetic aqueous solution.

Zr-based metal organic framework nanoparticles coated with a molecularly imprinted polymer for trace diazinon surface enhanced Raman scattering analysis

In this study, a new surface imprinted polymer of type MOFs-MIPs was synthesized with diazinon as template and Zr-based metal organic framework (UiO-67) as matrix for trace diazinon surface enhanced...

Synthesis of EDTA-functionalized graphene oxide-chitosan nanocomposite for simultaneous removal of inorganic and organic pollutants from complex wastewater

Discharging of inorganic and organic pollutants creates a serious threat to the human health and the environment. In the current work, we have synthesized Ethylenediaminetetraacetic acid (EDTA) functionalized graphene oxide-chitosan nanocomposite (GO-EDTA-CS) for simultaneous removal of inorganic (i.e., mercury (Hg(II) and copper (Cu(II)) and organic pollutants (i.e., methylene blue (MB) and crystal violet (CV)) from wastewater via adsorption process. The structural, functional, morphological, elemental compositions, surface area and thermal properties of the synthesized nanocomposite were identified using powder X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), field scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), Brunauer-Emmett-Teller (BET), and thermogravimetric analyzer (TGA), respectively. Different batch adsorption experiments such as pH effect, contact time, initial pollutants concentration, reusability etc. were studied in monocomponent system to optimize the results. The adsorption process apparently followed pseudo-second-order (PSO) kinetics for both pollutants, however the adsorption kinetics was also explained by the intra-particle diffusion model. The isotherm data for both metals ions and dyes were well fit by the Langmuir isotherm model. The maximum adsorption capacities of the adsorbent were determined 324 ± 3.30 130 ± 2.80, 141 ± 6.60, and 121 ± 3.50 mg g^-1 for Hg(II), Cu(II), MB, and CV, respectively. The excellent adsorption capacity was attributed to the availability of various active functional groups (e.g., -COOH, -OH, -NH₂, etc.) on the adsorbent. The EDS, elemental mapping and FTIR analysis performed before and after the adsorption of heavy metals and dyes by GO-EDTA-CS confirmed the simultaneous adsorption of the pollutants. Moreover, GO-EDTA-CS could maintain its adsorption capacity for both inorganic and organic pollutants even after seven cycles of adsorption-desorption, indicating itself a promising adsorbent for practical wastewater treatment containing both inorganic and organic toxic pollutants.

Recent innovations of nanotechnology in water treatment: A comprehensive review

Environmental pollution from organic and inorganic pollutants poses a threat to the ecosystem. Pollutant's prevalence and persistence have increased significantly in recent years. In order to enhance the quality of naturally accessible water to a level suitable for human consumption, a number of techniques have been employed. In this context, the use of cutting-edge nanotechnology to classical process engineering paves the way for technical encroachments in advanced water and wastewater technology. Nanotechnology has the potential to ameliorate the quality, availability, and viability of water supplies in the long run by facilitating reuse, recycling and remediation of water. The promising role of nanotechnology in wastewater remediation is highlighted in this paper, which also covers current advancements in nanotechnology-mediated remediation systems. Moreover, nano-based materials such as nano-adsorbents, photocatalysts, nano-metals and nanomembranes are discussed in this review of recent breakthroughs in nanotechnologies for water contaminant remediation.

Decontamination of fenitrothion from aqueous solutions using rGO/MoS2/Fe3O4 magnetic nanosorbent: synthesis, characterization and removal application

In the present work, rGO/MoS2/Fe3O4 nanocomposite was synthesized and after confirmation of the structure by FTIR, XRD, and FESEM techniques, its performance as nanosorbent was investigated for the removal of fenitrothion pesticide from the aqueous media. The parameters affecting the removal process including agitation time, pH of the reaction medium, adsorbent content, initial analyte concentration as well as desorption parameters were investigated and optimized. Under optimum conditions (pH = 7, adsorbent amount: 30 mg, adsorption and desorption time: 5 min, eluent type and volume: 0.01 M ethanol-acetic acid and 4 mL), the synthesized adsorbent was able to remove fenitrothion pesticide up to 98% with an adsorption capacity of 33.4 mg/g. By investigation of the line equation and the correlation coefficient value, it was found that the adsorption process, in this study, follows the Langmuir model.

Environmental Occurrence, Toxicity Concerns, and Degradation of Diazinon Using a Microbial System

Diazinon is an organophosphorus pesticide widely used to control cabbage insects, cotton aphids and underground pests. The continuous application of diazinon in agricultural activities has caused both ecological risk and biological hazards in the environment. Diazinon can be degraded via physical and chemical methods such as photocatalysis, adsorption and advanced oxidation. The microbial degradation of diazinon is found to be more effective than physicochemical methods for its complete clean-up from contaminated soil and water environments. The microbial strains belonging to Ochrobactrum sp., Stenotrophomonas sp., Lactobacillus brevis, Serratia marcescens, Aspergillus niger, Rhodotorula glutinis, and Rhodotorula rubra were found to be very promising for the ecofriendly removal of diazinon. The degradation pathways of diazinon and the fate of several metabolites were investigated. In addition, a variety of diazinon-degrading enzymes, such as hydrolase, acid phosphatase, laccase, cytochrome P450, and flavin monooxygenase were also discovered to play a crucial role in the biodegradation of diazinon. However, many unanswered questions still exist regarding the environmental fate and degradation mechanisms of this pesticide. The catalytic mechanisms responsible for enzymatic degradation remain unexplained, and ecotechnological techniques need to be applied to gain a comprehensive understanding of these issues. Hence, this review article provides in-depth information about the impact and toxicity of diazinon in living systems and discusses the developed ecotechnological remedial methods used for the effective biodegradation of diazinon in a contaminated environment.

Application of chitosan-alginate bio composite for adsorption of malathion from wastewater: Characterization and response surface methodology

Agricultural effluents in aqueous media have caused serious threats due to adversely affect human health and the ecosystem. In this study, the low-cost easily accessible chitosan-alginate adsorbent was prepared for the removal of malathion from agricultural effluents using microemulsion method. The adsorbent was characterized using scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), and Fourier-transform infrared spectroscopy (FTIR). The optimum experimental conditions, including adsorbent dosage (0.05-0.25 g), contact time (5-25 min), and concentration of malathion (5-25 mg L^-1) at five levels were studied using the composite central design (CCD) based on the response surface methodology (RSM). The highest removal percentage was obtained 82.35 with an adsorbent dosage of 0.18 g, contact time of 20 min, and initial concentration of 10 mg L^-1. The analysis of variance (ANOVA) was applied to assess the significance and adequacy of the model. The results revealed that quadratic model was proper for the prediction removal of malathion. The adsorption kinetics and isotherms were examined under optimal conditions. The Langmuir with a coefficient of determination (R²) = 0.99 and pseudo-second-order with R² = 0.99 were achieved as the best isotherm and kinetic models, respectively. The results showed that the chitosan-alginate biopolymer can be effective and affordable adsorbent for the removal of malathion from aqueous solution.

Toxicity and remediation of pharmaceuticals and pesticides using metal oxides and carbon nanomaterials

The worldwide development of agriculture and industry has resulted in contamination of water bodies by pharmaceuticals, pesticides and other xenobiotics. Even at trace levels of few micrograms per liter in waters, these contaminants induce public health and environmental issues, thus calling for efficient removal methods such as adsorption. Recent adsorption techniques for wastewater treatment involve metal oxide compounds, e.g. Fe2O3, ZnO, Al2O3 and ZnO-MgO, and carbon-based materials such as graphene oxide, activated carbon, carbon nanotubes, and carbon/graphene quantum dots. Here, the small size of metal oxides and the presence various functional groups has allowed higher adsorption efficiencies. Moreover, carbon-based adsorbents exhibit unique properties such as high surface area, high porosity, easy functionalization, low price, and high surface reactivity. Here we review the cytotoxic effects of pharmaceutical drugs and pesticides in terms of human risk and ecotoxicology. We also present remediation techniques involving adsorption on metal oxides and carbon-based materials.

Zencefilin (Zingiber officinale Roscoe) Diazinon Toksisitesine Karşı Koruyucu Rolünün Allium cepa L. Meristem Hücrelerinde Araştırılması

Yaygın olarak kullanılan bir pestisit olan diazinon hedef olmayan canlılar üzerinde toksik etkilere sahiptir. Bu çalışma, diazinonun meristem hücrelerinde teşvik ettiği toksisiteye karşı zencefilin koruyucu ve iyileştirici etkisini fizyolojik, genotoksik ve biyokimyasal parametrelerle araştırmayı hedeflemiştir. Ayrıca kök meristem hücrelerinde meydana gelen hasarlar incelenmiştir. Bu amaçla A. cepa soğanları 6 gruba ayrıldı (kontrol, 240 mg/L zencefil, 480 mg/L zencefil, 500 mg/L diazinon, 500 mg/L diazinon + 240 mg/L zencefil ve 500 mg/L diazinon + 480 mg/L zencefil). Diazinon süperoksit dismutaz aktivitesi, katalaz aktivitesi, malondialdehit seviyesi, mikronükleus sıklığı, kromozomal anormallik yoğunluğu ve meristematik hücre hasarlarını arttırmış; ancak mitotik indeksi, çimlenme yüzdesi, kök uzunluğu, ağırlık artışı azaltmıştır. Zencefil, diazinon ile birlikte uygulandığında doza bağlı olarak tüm bu toksisite göstergelerini düşürmüştür. Bu çalışma, A. cepa modeli kullanılarak diazinonun hedef olmayan organizmalar üzerindeki toksik etkilerine karşı zencefilin koruyucu bir rolünü açıkça göstermiştir.

Photo-catalytic degradation of bisphenol-a from aqueous solutions using GF/Fe-TiO2-CQD hybrid composite

In this photocatalytic study, removal of bisphenol-A from aqueous solution was studied using the GF/Fe-TiO2-CQD composite. Due to its health and environmental effects, this compound should be disposed of sources that are mainly industrial wastewater. The phis-chemical properties of the composite were determined by traditional analyzes of EF-SEM, EDX, BET, XRD, FTIR and DRS. In this study, different ratios of CQD in the composite (1.5, 4.5 and 7.5 wt%), pH, and bisphenol-A concentration as variable parameters were investigated. All analyzes, EF-SEM, EDX, BET, XRD, FTIR, show that the GF/Fe-TiO2-CQD composite is well coated on glass fibers (GF) and all the elements in the catalyst are present. On the other hand, DRS analysis showed that CQD reduces the band gap of Fe-TiO2 from 2.96 eV to 2.91 eV, it was 3.10 eV for TiO2. Among different catalysts, GF/Fe-TiO2-CQD4.5wt% has the best performance. The results showed that for GF/Fe-TiO2-CQD4.5wt%, optimum for the process was at pH = 6 in low concentration of bisphenol-A. The first order model for the photocatalytic degradation process were well studied. In addition, GF/Fe-TiO2-CQD4.5wt% showed that it can be used many times with a minimal reduction in performance. As a result, the GF/Fe-TiO2-CQD4.5wt% composite can successfully remove bisphenol-A form in synthetic aqueous solution. However, it is necessary to further studies to applied that for real water source in water and wastewater treatment plants.

Ultrasonic coupling with electrical current to effective activation of Persulfate for 2, 4 Dichlorophenoxyacetic acid herbicide degradation: modeling, synergistic effect, and a by-product study

In this research work, we investigated the ability of the oxidative degradation of 2, 4-Dichlorophenoxy acetic acid herbicide via ultrasonic-assisted in electro-activation of the persulfate system in the presence of nano-zero valent iron. The effect of experimental parameters such as pH value [4-8], electrical current (0.5-1 A), persulfate concentration (0.25-0.5 mg.l-1), nano zero-valent iron dose (0.05-0.1 mg.l-1), and initial organic pollutant concentration (50-100 mg.l-1) on the ultrasonic-electropersulfate process performance was assessed via central composite design. The combination of ultrasonic waves with the electrochemical process to activation of persulfate showed better efficiency into 2, 4-Dichlorophenoxy acetic acid herbicide degradation compared to their implementation in individual and binary systems. Following optimal conditions (pH = 5.62, 0.80 A applied electrical current, 0.39 mg/L persulfate concentration, 0.07 mg/L nano-zero valent iron, and 50 mg/L 2,4-Dichlorophenoxy acetic acid concentration in 40 min reaction), nearly 91% removal was done. Moreover, the complete removal of 2, 4-Dichlorophenoxy acetic acid, 92% COD, and 88% TOC removal was achieved by this process near 140 min reaction. The scavenging experiment confirmed the role of free oxidizing species in the degradation of 2, 4-Dichlorophenoxy acetic acid during the process. Approximately 50% improved 2, 4-Dichlorophenoxy acetic acid removal in the process against the inclusive efficiency of single mechanisms. The obtained results were fitted to the pseudo-first-order kinetic model with a high correlation coefficient (R2 = 0.96). Five important intermediate products of 2, 4-D oxidation were 2, 4-dichlorophenol (2, 4-DCP), 2, 6-dichlorophenol (2, 6-DCP), 4, 6 dichlororesorcinol (4, 6-DCR), 2-chlorohydroquinone (2-CHQ), and 2-chloro-1, 4-benzoquinone (2-CBQ). In the end, can be employed as a satisfactory advanced oxidation process in high mineralization of 2, 4-D and refractory organic pollutants.

A global systematic review, meta-analysis and health risk assessment on the quantity of Malathion, Diazinon and Chlorpyrifos in Vegetables

It is widely believed that an increasing trend in the production and consumption of vegetables has led to a dramatic rise in the use of pesticides potentially threatening the health of consumers around the world. This systematic study along with meta-analysis has mainly centered on the evaluation of the quantity of three well-known pesticides namely, Malathion (MLT), Diazinon (DZN) and Chlorpyrifos (CPF) in vegetables. In this regard, a comprehensive literature search has been performed over the last decade (January 1, 2011 to June 21, 2020) within the scientific databases including PubMed, Web of Science, and Scopus. Of 1239 articles identified through the database screening, 22 plus 37 data report were retained and included in the meta-analysis phase. Additionally, the probabilistic human health risks for the consumers due to the intake of CPF, DZN and MLT from eating vegetables were estimated by the Monte Carlo Simulated (MCS) method. According to the findings, the maximum quantities of MLT, DZN and CPF in the vegetables were observed in Pakistan (222 μg/kg, 95%CI = 214.94-229.08), Thailand (245.00, 95% CI = 235.2-254.8) and South Korea (440 μg/kg, 95% CI = 437.19-442.81), while the lowest concentration levels were reported in China (1.7 μg/kg, 95% CI = 1.56-1.84), Poland (0.57, 95% CI = 0.46-0.68) and Poland (5.78 μg/kg, 95% CI = 4.40-7.12), respectively. The results of the Egger's and the Begg's tests revealed that no bias with regard to the potential publication was observed. Finally, non-carcinogenic risk assessment results demonstrated that the exposure to the studied pesticides thorough vegetables consumption could not threaten the health of consumers.

High effective removal of diazinon from aqueous solutions using the magnetic tragacanth-montmorillonite nanocomposite: isotherm, kinetic, and mechanism study

Health and environmental impact of pesticide contamination of groundwater has been reported repeatedly in many studies. The removal of diazinon from agricultural wastewater is still of great interest due to using widely in many developing countries. In the presented study, the magnetic tragacanth-montmorillonite nanocomposite was utilized as an adsorbent to remove diazinon from an aqueous solution. The adsorbent properties were characterized using FE-SEM, EDX, FTIR, XRD, BET, and VSM techniques. The influence of adsorbent dosage, pH, contact time, and initial concentration of diazinon was studied in a batch system. Different adsorption kinetics and isotherm models were used to describe the kinetic and equilibrium data. The results indicated that the adsorption kinetic was fitted better with a Elovich kinetic model, and the adsorption isotherm was well described by the Langmuir-Freundlich model, and the maximum adsorption capacity was 416 mg g^-1. According to Weber and Morris's model and Boyd plot, the results demonstrated that the adsorption kinetic was controlled simultaneously by film diffusion and intraparticle diffusion. Besides, a thermodynamic study showed that the removal of diazinon is an endothermic process. Considering the results, magnetic tragacanth-montmorillonite nanoadsorbent has a high capability to remove diazinon from aqueous solution.

Risk assessment and the adsorptive removal of some pesticides from synthetic wastewater: a review

Background

The need for environmental protection and remediation processes has been an increasing global concern. Pesticides are used as biological agents, disinfectants, antimicrobials, and also in a mixture of some chemical substances. Their modes of application are through selective dispensing and attenuation processes which act upon any pest that compete with the production, processing, and storage of foods and also in agricultural commodes. The pests might comprise weeds, insects, birds, fish, and microbes.

Main body

Pesticides are commonly found in water surface, landfill leachate, ground water, and wastewater as pollutant. An overview of recently studied adsorption processes for the pesticide elimination from polluted water has been reported in this study utilizing activated carbon, clay materials, biomass materials, metal organic frame work, graphene, and carbon-based materials as well as agricultural wastes as adsorbents. The risk assessment and cost analysis of adsorbents were also provided.

Conclusion

Evidences from literature recommend modified adsorbent and composite materials to have a prospective use in pesticide removal from wastewater. The adsorption data obtained fitted into different isotherm and kinetic models and also the thermodynamic aspect have been discussed.

Graphical abstract

Assessment of pesticides in water using time-weighted average calibration of passive sampling device manufactured with carbon nanomaterial coating on stainless steel wire

The continued contamination of water sources by pesticides is a problem that involves the life of aquatic organisms and human health, especially in countries whose economy is based on agriculture. The need to know the quality of drinking water under these circumstances is a priority for the public health of any community. Passive sampling methods allow the determination of long-term environmental pollutants through a single sample collection, reducing time and cost of analyses. One advantage of passive sampling is that it is possible to calculate a time-weighted average (TWA) concentration value or an equilibrium concentration value, depending on the type of device used and the exposure time. Passive sampling techniques using carbon nanomaterials (CNMs) have a high potential for pesticide sampling in aquatic systems. A device for passive sampling manufactured with CNMs in a microextraction system and recyclable materials was calibrated in laboratory exposure conditions over 15 days. The calibration results showed linear accumulation periods between 5 and 10 days. Sampling rates were between 0.014 and 0.146 mL day^-1. The sampler was field-tested in the San Francisco river basin in the state of Minas Gerais in Brazil for 7 days. This research allowed for the detection and calculation of TWA concentrations for organochlorine pesticides such as α-HCH, 4,4-DDE, and 4,4-DD in water sources. The manufactured device demonstrated greater sensitivity than the grab sampling processes for the detection of pesticides. The performed passive sampling system using gas chromatography/mass spectrometry (GC/MS) technique allowed for the collection, detection, identification, and quantification of 26 pesticides.

New frontiers and prospects of metal-organic frameworks for removal, determination, and sensing of pesticides

Pesticides have been widely used in agriculture to control, reduce, and kill insects. Humans are also being using pesticides to control insidious animals in daily life. By these practices, a huge volume of pesticides is introduced to the environment. Despite broad-spectrum applicability, pesticides also have hazardous effects on both humans and animals at high and low concentrations. Long-term exposure to pesticides can cause different diseases, like leukemia, lymphoma, and cancers of the brain, breasts, prostate, testis, and ovaries. Reproductive disorders from pesticides include birth defects, stillbirth, spontaneous abortion, sterility, and infertility. Therefore, the application of determination and treatment methods for pre-concentration and removal of these toxic materials from the environment appears a vital concern. To date, different materials and approaches have been employed for these purposes. Among these approaches, multifunctional metal-organic frameworks (MOFs)-assisted adsorption and determination processes have always been in the spotlight. These facts are due to exclusive properties of MOFs in terms of the crystallinity, large surface area, high chemical, and physical stability, and controllable structure as well as unique features of adsorption and determination process in terms of simple, easy, cheap, available method and ability to use in large and industrial scales. In the present work, we illustrate the exceptional features of MOFs as well as the possible mechanism for the adsorption of pesticides by MOFs. The use of these fantastic materials for pre-concentration and removal of pesticides are extensively explored. In addition, the performance of MOFs was compared with other adsorbents. Finally, the new frontiers and prospects of MOFs for the determination, sensing, and removal of pesticides are presented.