Insights into the simultaneous removal of Cr6+ and Pb2+ by a novel sewage sludge-derived biochar immobilized nanoscale zero valent iron: Coexistence effect and mechanism

Complexing agent-assisted Cr(VI) removal in a continuous fixed-bed system with nanoscale Fe0/NaA molecular sieve membrane supported on nickel foam

Complexing agents (CAs) can be used for the removal of Cr(VI) via nanoscale Fe0 (nZVI) reduction in cost-effective manner. However, nZVI is prone to aggregation and passivation, and some conventional CAs are toxic and difficult to biodegrade, potentially causing secondary pollution. Therefore, selecting an environmentally friendly CA for assisting in the removal of Cr(VI) via supported nZVI is imperative. Herein, NaA molecular sieve membrane-supported nZVI (nZVI/NaA-NF) was prepared via the secondary growth and liquid-phase reduction method using nickel foam (NF) as the carrier. The physicochemical characteristics of nZVI/NaA-NF before and after reaction were analysed via SEM, EDS, and XPS. A CA-improved nZVI/NaA-NF was used for the effective removal of Cr(VI) in a continuous fixed-bed system. Furthermore, the influences of various experimental factors including the CA type, CA concentration, solution pH, space velocity, and inlet Cr(VI) concentration on Cr(VI) removal were systematically investigated. The results demonstrated that nZVI particles were homogeneously immobilized on the NaA molecular sieve membrane/NF for fresh nZVI/NaA-NF, and tetrasodium iminidisuccinate (IDS-4Na) inhibited the aggregation of Cr(III)/Fe(III) (hydr)oxide precipitates during the reaction. IDS-4Na demonstrated excellent promotive effect on Cr(VI) removal via nZVI/NaA-NF. The breakthrough time for Cr(VI) in the addition of IDS-4Na was considerably longer than that of nZVI/NaA-NF alone. The breakthrough concentration of Cr(VI) only reached 1.1% and 9.9% of the inlet concentration at 220 and 240 min, with an IDS-4Na concentration of 4 mM, a pH of 2.5, and a space velocity of 0.265 min-1. The Bohart-Adams model was appropriate to predict the initial part of Cr(VI) breakthrough curves in the nZVI/NaA-NF fixed bed. The saturated concentration (N0) increased with an increase in inlet Cr(VI) concentration. The Yoon-Nelson model afforded good fitting results for all breakthrough curves of Cr(VI). The k' value increased with an increase in space velocity, and the τ value decreased.

Cobalt/Iron Bimetallic Biochar Composites for Lead(II) Adsorption: Mechanism and Remediation Performance

The performance of nano-zero-valent iron for heavy metal remediation can be enhanced via incorporation into bimetallic carbon composites. However, few economical and green approaches are available for preparing bimetallic composite materials. In this study, novel Co/Fe bimetallic biochar composites (BC@Co/Fe-X, where X = 5 or 10 represents the CoCl2 concentration of 0.05 or 0.1 mol L-1) were prepared for the adsorption of Pb2+. The effect of the concentration of cross-linked metal ions on Pb2+ adsorption was investigated, with the composite prepared using 0.05 mol L-1 Co2+ (BC@Co/Fe-5) exhibiting the highest adsorption performance. Various factors, including the adsorption period, Pb2+ concentration, and pH, affected the adsorption of Pb2+ by BC@Co/Fe-5. Further characterisation of BC@Co/Fe-5 before and after Pb2+ adsorption using methods such as X-ray diffraction and X-ray photoelectron spectroscopy suggested that the Pb2+ adsorption mechanism involved (i) Pb2+ reduction to Pb0 by Co/Fe, (ii) Co/Fe corrosion to generate Fe2+ and fix Pb2+ in the form of PbO, and (iii) Pb2+ adsorption by Co/Fe biochar. Notably, BC@Co/Fe-5 exhibited excellent remediation performance in simulated Pb2+-contaminated water and soil with good recyclability.

Effect and mechanism of kaolinite loading amorphous zero-valent iron to stabilize cadmium in soil

Amorphousness effectively improves the electron transfer rate of zero-valent iron. In this study, a novel kaolinite loading amorphous zero-valent iron composite (K-AZVI) was prepared and applied to the remediation of soils with cadmium (Cd) pollution concentrations of 20, 50, and 100 mg/kg respectively. The results showed that the application of K-AZVI increased the pH and cation exchange capacity (CEC) of soil, and decreased the dissolved organic carbon (DOC) and organic matter (OM) of soil, thus indirectly promoting the adsorption of Cd in the soil. After 28 days of stabilization, the stabilizing efficiency of K-AZVI on the water-soluble Cd content in soil reached 98.72 %. Under the amendment of 0.25 %-1.0 % (w/w), the available Cd content in 20-100 mg/kg contaminated soil decreased by 46.47 %-62.23 %, 24.10 %-41.52 %, and 16.09 %-30.51 % respectively compared with CK. More importantly, the addition of K-AZVI promoted the transformation of 33.18 %-48.42 % exchangeable fraction (EXC) to 10.09 %-20.14 % residual fraction (RES), which increased the abundance and diversity of soil bacterial communities. Comprehensive risk assessment showed that adding 1.0 % K-AZVI provided the best remediation on contaminated soil. In addition, the results of scanning electron microscopy (SEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) of K-AZVI before and after the reaction showed that the stabilization mechanism of K-AZVI to Cd in soil is mainly the stable metal species (Cd(OH)2, CdO and CdFe2O4) formed by the direct complexation and coprecipitation of a large number of iron oxides formed by the rapid corrosion of amorphous zero-valent iron (AZVI). Overall, this work provides a promising approach to the remediation of Cd-contaminated soil using K-AZVI composites.

Degradation of Levofloxacin by a green zero-valent iron-loaded carbon composite activating peroxydisulfate system: Reactivity, products and mechanism

In this study, a green zero-valent iron-loaded carbon composite (ZVI-SCG) was synthesized using coffee grounds and FeCl3 solution through two-steps method, and the synthesized ZVI-SCG was used in the activation of peroxydisulfate (PDS) to degrade Levofloxacin (LEX). Results revealed that ZVI-SCG exhibited a great potential for LEX removal by adsorption and catalytic degradation in the ZVI-SCG/PDS system, and 99% of LEX was removed in the ZVI-SCG/PDS system within 60 min. ZVI-SCG/PDS system showed a high reactivity toward LEX degradation under realistic environmental conditions. Also, the ZVI-SCG/PDS system could effectively degrade several quinolone antibiotics including gatifloxacin, ciprofloxacin and LEX in single and simultaneous removal modes. A potential reaction mechanism of LEX degradation by ZVI-SCG/PDS system was proposed, SO4•-, HO•, O2•- and 1O2 involved in radical and non-radical pathways took part in catalytic degradation of LEX by ZVI-SCG/PDS system, but HO• might be the main reactive species for LEX degradation. The possible degradation pathway of LEX was also proposed based on the identified ten intermediate products, LEX degradation was successfully achieved through decarboxylation, opening ring and hydroxylation processes. The potential toxicity of LEX and its oxidation products decreased significantly after treatment. This study provides a promising strategy of water treatment for the antibiotics-containing wastewater.

A green synthesized medicine residue carbon-based iron composite for the removal of chromium (VI) and cadmium (II): Performance, kinetics and mechanism

Nowadays, clean-up of heavy metals from wastewaters using waste residue carbon-based material has received increasing attention. In this work, a novel Chinese medicine residue carbon-based nano zero-valent iron composite (CM-nZVI) had been successfully prepared using the combined Chinese medicine residue, FeCl3 and green tea extract. Cr(VI) and/ or Cd(II) removal in water by the CM-nZVI were systematacially investigated with a series of batch experiments. The most relevant findings indicated the adsorption efficiecy and capacity of Cr(VI) by CM-nZVI were respecitvely nearly 98% and 26 mg/g under optimized reaction conditions. The negative influences of the cations on the Cr(VI) removal followed the order of Al3+ > Ca2+ > Mg2+ Na+ > K+, but the anions followed the order of HCO3- > PO43- > NO3- > Cl- > SO42-. Humic acid (HA) and ionic strength with high concentrations severely inhibited Cr(VI) removal. The Cr(VI) adsorption on CM-nZVI fitted well by the pseudo-second-order kinetic and Langmuir models. A monolayer endothermic chemisorption occurred on Cr(VI) adsorption over CM-nZVI, and Cr(VI) removal by CM-nZVI primarily involved in the absorption, reduction, precipitation and complexation processes. Both Cr(VI) and Cd(II) removals had been achieved by CM-nZVI at their low concentrations. This CM-nZVI showed a better reusability proprity for Cr(VI) and Cd(II) removal with the regeneration of CM-nZVI through simple pickling. The outcomes of this work show that CM-nZVI could be used an effective material for heavy metals removal from water.

Metabolomic profiles reveals the dose-dependent effects of rice grain yield and nutritional quality upon exposure zero-valent iron nanoparticles

Zero-valent iron nanoparticles (nZVI) were widely used material in environmental remediation, which has attracted increasing concern for their safety. Previous studies have shown that the addition of nZVI could inhibit rice seedling growth. However, the effect of nZVI on the soil-rice system during the entire life cycle was not reported. Furthermore, the effect of nZVI on the quality of rice grain has also not been studied. Therefore, we investigated the effects of rice grain yield and nutritional quality upon exposure nZVI. The results showed that the soil pH value, redox potential and Fe (II) content in the nZVI-treated group were decreased in a dose-dependent manner. Interestingly, 2500 mg/kg nZVI significantly decreased the relative abundance of several functional microbial communities (10.52-73.53 %) associated with carbon and nitrogen cycles in response to plants compared to the control. Meanwhile, the nZVI treatment clearly reduced grain yield (8.71-18.21 %). Furthermore, the content of protein (51.72-57.79 %) and several essential nutrients (Zn, Cu, Mn and Mo) in the nZVI-treated grains was also decreased in a dose-dependent manner. The results of grain metabolomics indicated that nZVI could interfere with the relative expression of lysine and glutathione by regulating the metabolic pathways of antioxidant and protein synthesis in rice.

Magnetic Biochar Derived from Fenton Sludge/CMC for High-Efficiency Removal of Pb(II): Synthesis, Application, and Mechanism

Magnetic biochar composites (MBC) were developed by a simple one-step pyrolysis method using Fenton sludge waste solid and carboxymethyl cellulose sodium. Detailed morphological, chemical, and magnetic characterizations corroborate the successful fabrication of MBC. Batch adsorption experiments show that the synthesized MBC owns high-efficiency removal of Pb(II), accompanied by ease-of-separation from aqueous solution using magnetic field. The experiment shows that the equilibrium adsorption capacity of MBC for Pb(II) can reach 199.9 mg g^-1, corresponding to a removal rate of 99.9%, and the maximum adsorption capacity (q_m) reaches 570.7 mg g^-1, which is significantly better than that of the recently reported magnetic similar materials. The adsorption of Pb(II) by MBC complies with the pseudo second-order equation and Langmuir isotherm model, and the adsorption is a spontaneous, endothermic chemical process. Investigations on the adsorption mechanism show that the combination of Pb(II) with the oxygen-containing functional groups (carboxyl, hydroxyl, etc.) on biochar with a higher specific surface area are the decisive factors. The merits of reusing solid waste resource, namely excellent selectivity, easy separation, and simple preparation make the MBC a promising candidate of Pb(II) purifier.

Efficient degradation of hexabromocyclododecane using montmorillonite supported nano-zero-valent iron and Citrobacter sp. Y3

The coupling of modified nanoscale zero-valent iron (nZVI) with organohalide-degrading bacteria provides a promising solution for the remediation of hexabromocyclododecane (HBCD)-contaminated environments. However, the interactions between modified nZVI and dehalogenase bacteria are intricate, and the mechanisms of synergistic action and electron transfer are not clear, and requires further specific investigation. In this study, HBCD was used as a model pollutant, and stable isotope analysis revealed that organic montmorillonite (OMt)-supported nZVI coupled with the degrading bacterial strain Citrobacter sp. Y3 (nZVI/OMt-Y3) can use [¹³C]HBCD as the sole carbon source and degrade or even mineralise it into ¹³CO₂ with a maximum conversion rate of 100% within approximately 5 days. Analysis of the intermediates showed that the degradation of HBCD mainly involves three different pathways: dehydrobromination, hydroxylation, and debromination. The proteomics results showed that nZVI introduction promoted the transport of electrons and debromination. Combining the results from XPS, FTIR, and Raman spectroscopy with the analysis results of proteinomics and biodegradation products, we verified the process of electron transport and proposed a metabolic mechanism of HBCD degradation by the nZVI/OMt-Y3. Moreover, this study provides insightful avenues and models for the further remediation of HBCD and other similar pollutants in the environment.

Remediation and its biological responses to Cd(II)-Cr(VI)-Pb(II) multi-contaminated soil by supported nano zero-valent iron composites

Multi-metal contaminated soil has received extensive attention. The biochar and bentonite-supported nano zero-valent iron (nZVI) (BC-BE-nZVI) composite was synthesized in this study by the liquid-phase reduction method. Subsequently, the BC-BE-nZVI composite was applied to immobilize cadmium (Cd), chromium (Cr), and lead (Pb) in simulated contaminated soil. The simultaneous immobilization efficiencies of Cd, Cr(VI), Cr_total, and Pb were achieved at 70.95 %, 100 %, 86.21 %, and 100 %, respectively. In addition, mobility and bioavailabilities of Cd, Cr, and Pb were significantly decreased and the risk of iron toxicity was reduced. Stabilized metal species in the contaminated soil (e.g., Cd(OH)₂, Cd-Fe-(OH)₂, Cr_xFe_1-xOOH, Cr_xFe_1-x(OH)₃, PbO, PbCrO₄, and Pb(OH)₂) were formed after the BC-BE-nZVI treatment. Thus, the immobilization mechanisms of Cd, Cr, and Pb, including adsorption, reduction, co-precipitation, and complexation co-exist with the metals. More importantly, bacterial richness, bacterial diversity, soil enzyme activities (dehydrogenase, urease, and fluorescein diacetate hydrolase), and microbial activity were enhanced by applying the BC-BE-nZVI composite, thus increasing the soil metabolic function. Over all, this work applied a promising procedure for remediating multi- metal contaminated soil by using the BC-BE-nZVI composite.

Release characteristics of heavy metals from electrolytic manganese residue under varying environmental factors

High levels of manganese (Mn) and other heavy metals from electrolytic manganese residue (EMR) stockpiled would be released into the environment under natural conditions. A batch-leaching test was carried out to investigate the release characteristics of heavy metals from EMR with different storage times under simulated environmental conditions such as acid rain with different pH (3.0, 4.5, 5.6, and 7.0) at contact times of 1, 2, 4, 6, and 12 h; liquid to solid ratio (L/S) (5:1, 10:1, 20:1, and 30:1); and temperature (15, 25, 35, and 45 °C). The results showed that low pH (3.0 and 4.5) and high temperature (35 and 45 °C) could significantly promote heavy metal leaching from EMRs and increasing the L/S ratio above 20:1 mL/g significantly decreased heavy metal leachate concentrations due to dilution effect. Cr, Mn, and Pb concentrations in leachate increased almost continuously throughout the leaching process, while Zn decreased slightly at the 12th hour. Meanwhile, heavy metal concentrations in EMR1 (fresh EMR) were higher than in EMR2 (out stockpiled for more than 3 months). The concentrations of Mn, Pb, and Zn in leachates from EMRs at pH 3.0 and 4.5 leaching far exceeded the allowable maximum discharge concentrations for pollutants of the integrated wastewater discharge standard in China (GB8978-1996) by 57.5-59.0, 1.3-4.3, and 1.1-1.8 and 53.5-56.0, 3.04-7.25, and 1.0-1.91 times, respectively. Additionally, the Mn concentrations from both EMR leachates at pH 7.0 were above the national safe emission threshold. The morphological structure of EMRs changed after leaching, and XRD analysis showed the disappearance of MnO₂, SiO₂, FeS₂, and CaSO₄. The XPS revealed that Cr, Mn, Pb, and Zn existed as Cr³⁺, MnO, PbSO₄, and ZnSiO₃, respectively, after leaching. The study concluded that Mn, Pb, and Zn from EMRS leached by acid rain might pose a high potential environmental risk. Therefore, developing appropriate disposal techniques for EMR is necessary to prevent heavy metal pollution.

Enhanced Cr (VI) reduction and removal by Fe/Mn oxide biochar composites under acidic simulated wastewater

Chromium (Cr (VI)) can cause severe damage to the ecosystem and humans because of its toxicity. In this paper, the adsorbed Fe/Mn ions Bacillus cereus ZNT-03, lotus seeds, and graphene oxide were co-cultured as the raw materials. Fe/Mn oxide biochar composite (FMBC) was prepared to treat Cr (VI) by one-step pyrolysis. FMBC has high-density micropores, and the average pore size is about 0.82 nm. Fe (II), Mn (II), and N-containing functional groups could serve as electron donors for Cr (VI) reduction. The removal of Cr (VI) is monolayer chemisorption and pH-dependent. The maximum adsorption capacity of FMBC is 21.25 mg g^-1. Cr (VI) is reduced and adsorbed on FMBC by physical adsorption, reduction, complexation, electrostatic attraction, and coprecipitation. The contribution ratio of the reduction mechanism to Cr (VI) is 72.25%. The packed column and regeneration experiments indicated that FMBC had excellent adsorption stability even after soaking in acidic simulated wastewater after 180 days (pH 1.5). These results indicate that FMBC can provide rapid reduction and efficient adsorption for Cr (VI), making it possible to apply in water treatment.

Phytoremediation plants (ramie) and steel smelting wastes for calcium silicate coated-nZVI/biochar production: Environmental risk assessment and efficient As(V) removal mechanisms

Arsenic is one of the most common and harmful pollutants in environment throughout the world, especially in aqueous solutions. In this study, two kinds of industrial solid wastes (Oxide scale (OS) and Blast furnace slag (BFS)) and one kind of phytoremediation plant waste (Ramie stalk) were used to prepare an environmentally friendly, low-cost, and efficient calcium silicate coated nano zero-valent iron (nZVI)/biochar composite (BOS) for As(V) adsorption. The potential environmental risks of BOS and their effects on removal of arsenic ions from aqueous media were investigated. The adsorption mechanism was explored and discussed based on XRD, SEM-EDS, XPS, etc. The results suggested that the environmental risk and heavy metals toxicity in BOS by co-pyrolysis were significantly reduced compared to the original materials, and no additional contaminant was observed in the subsequent experiments. Simultaneously, the BOS showed excellent As(V) removal capacity (>99%) and regenerative properties. The As(V) removal mechanisms are mainly ascribed to the complexation and co-precipitation between Fe and As, and the hydrogen bond between CO functional group of BOS and As. The mechanism of enhanced nZVI activity for As(V) removal was revealed. A protective layer of Ca₂SiO₄ was formed on the surface of nZVI during the co-pyrolysis process to prevent the passivation of nZVI. During the reaction process, the Ca₂SiO₄ covering the nZVI surface would be continuously detached to expose the fresh surface of nZVI, thus providing more redox activity and adsorption sites. This study provides a new way to treat and recycle industrial steel solid wastes and phytoremediation plant wastes, and the produced calcium silicate coated-nZVI/biochar composite is proposed to be a very promising material for practical remediation of As(V)-contaminated water bodies.

Cr(VI) immobilization in soil using lignin hydrogel supported nZVI: Immobilization mechanisms and long-term simulation

A novel nanocomposite, named as nZVI@LH, was prepared by nanoscale zero-valent iron (nZVI) supported on lignin hydrogel and was used in the remediation of Cr(VI)-contaminated soil collected from an industrial site. Meanwhile, scanning electron microscopy with energy dispersive X-ray (SEM-EDX) and X-ray diffractometry (XRD) results determined that nZVI nanoparticles disperse uniformly on hydrogel. After the 14 days remediation, the immobilization efficiency of Cr(VI) could reach over 87% in the treatment of 3% (w/w%) nZVI@LH and 26% in the treatment of bare-nZVI. Leaching experiment results showed that the treatment group with 3% (w/w%) nZVI@LH was up to the national leaching toxicity identification standard, and there was no threat in simulation of acid rain over the long term. The water-soluble (WS) fraction in 3^# nZVI@LH treatment decreased 31.1%, while the Fe-Mn oxide bound (OX) fraction and organic matter-bound (OM) fraction increased 10.9% and 13.4%, respectively. Moreover, nZVI@LH had limited impact on soil properties and the capability to immobilize Cr over a long period exposure to acid rain. This work prove that nZVI@LH has the potential to remediate Cr contaminated soil. Furthermore, details of possible mechanistic insight into the Cr remediation were carefully discussed.

Fate and mechanistic insights into nanoscale zerovalent iron (nZVI) activation of sludge derived biochar reacted with Cr(VI)

While nanoscale zero-valent iron modified biochar (nZVI-BC) have been widely investigated for the removal of heavy metals, the corrosion products of nZVI and their interaction with heavy metals have not been revealed yet. In this paper, nZVI-BC was synthesized and applied for the removal of Cr(VI). Batch experiments indicated that the adsorption of Cr(VI) fit Langmuir isotherm, with the maximum removal capacity at 172.4 mg/g at pH 2.0. SEM-EDS, BET, XRD, FT-IR, Raman and XPS investigation suggested that reduction of Cr(VI) to Cr(III) was the major removal mechanism. pH played an important role on the corrosion of nZVI-BC, at pH 4.5 and 2.0, FeOOH and Fe₃O₄ were detected as the major iron oxide, respectively. Therefore, FeOOH-BC and Fe₃O₄-BC were further prepared and their interaction with Cr were studied. Combining with DFT calculations, it revealed that Fe₃O₄ has higher adsorption capacity and was responsible for the effective removal of Cr(VI) through electrostatic attraction and reduction under acidic conditions. However, Fe₃O₄ will continue to convert to the more stable FeOOH, which is the key to for the subsequent stabilization of the reduced Cr(III). The results showed that the oxide corrosion products of nZVI-BC were subjected to the environment, which will eventually affect the fate and transport of the adsorbed heavy metal.

A sustainable reuse strategy of converting waste activated sludge into biochar for contaminants removal from water: Modifications, applications and perspectives

Conversion of sewage sludge to biochar for contaminants removal from water achieves the dual purpose of solid waste reuse and pollution elimination, in line with the concept of circular economy and carbon neutrality. However, the current understanding of sludge-derived biochar (SDB) for wastewater treatment is still limited, with a lack of summary regarding the effect of modification on the mechanism of SDB adsorption/catalytic removal aqueous contaminants. To advance knowledge in this aspect, this paper systematically reviews the recent studies on the use of (modified) SDB as adsorbents and in persulfate-based advanced oxidation processes (PS-AOPs) as catalysts for the contaminants removal from water over the past five years. Unmodified SDB not only exhibits stronger cation exchange and surface precipitation for heavy metals due to its nitrogen/mineral-rich properties, but also can provide abundant catalytic active sites for PS. An emphatic summary of how certain adsorption removal mechanisms of SDB or its catalytic performance in PS-AOPs can be enhanced by targeted regulation/modification such as increasing the specific surface area, functional groups, graphitization degree, N-doping or transition metal loading is presented. The interference of inorganic ions/natural organic matter is one of the unavoidable challenges that SDB is used for adsorption/catalytic removal of contaminants in real wastewater. Finally, this paper presents the future perspectives of SDB in the field of wastewater treatment. This review can contribute forefront knowledge and new ideas for advancing sludge treatment toward sustainable green circular economy.

Adsorption of chromium, copper, lead and mercury ions from aqueous solution using bio and nano adsorbents: A review of recent trends in the application of AC, BC, nZVI and MXene

Recent trends in adsorption of Chromium (Cr), Copper (Cu), Lead (Pb) and Mercury (Hg) in wastewater using (i) carbonaceous materials including activated carbon (AC) and biochar (BC), and (ii) nanomaterials including nano zero-valent iron (nZVI) and MXenes have been discussed in this paper. It has been found that adsorption capacity depends largely on the adsorbent modification technique, initial pH of wastewater, dosage of adsorbent, contact time and initial concentration of the pollutants. The pH value ranges for maximum removal of Cr, Cu, Pb and Hg have been reported as 2-4, 5-6, 5-8 and 3-8, respectively. Up to 99% removal of metals has been reported using AC, BC, nZVI and MXene. The mechanism involves the reduction and chemical adsorption of metals. AC and BC have a higher surface area (up to 5000 m²/g) compared to nZVI (up to 500 m²/g) and MXene (up to 67.66 m²/g). However, the higher reactivity and regeneration capacity of nZVI and MXene make them suitable adsorbents. From a practical point of view the application of adsorbents for real effluents, cost analysis, regeneration capability and reuse of heavy metals are some aspects that need attention in future studies. The removal efficiencies of AC and BC are comparable to the nZVI and MXene. The cost analysis may be an attractive aspect to decide the future application of these adsorbents at large scale.

Removal of hexavalent chromium via biochar-based adsorbents: State-of-the-art, challenges, and future perspectives

Chromium originates from geogenic and extensive anthropogenic activities and significantly impacts natural ecosystems and human health. Various methods have been applied to remove hexavalent chromium (Cr(VI)) from aquatic environmental matrices, including adsorption via different adsorbents, which is considered to be the most common and low-cost approach. Biochar materials have been recognized as renewable carbon sorbents, pyrolyzed from various biomass at different temperatures under limited/no oxygen conditions for heavy metals remediation. This review summarizes the sources, chemical speciation & toxicity of Cr(VI) ions, and raw and modified biochar applications for Cr(VI) remediation from various contaminated matrices. Mechanistic understanding of Cr(VI) adsorption using different biochar-based materials through batch and saturated column adsorption experiments is documented. Electrostatic interaction and ion exchange dominate the Cr(VI) adsorption onto the biochar materials in acidic pH media. Cr(VI) ions tend to break down as HCrO₄^-, CrO₄^2-, and Cr₂O₇^2- ions in aqueous solutions. At low pH (∼1-4), the availability of HCrO₄^- ions attributes the electrostatic forces of attraction due to the available functional groups such as -NH₄⁺, -COOH, and -OH₂⁺, which encourages higher adsorption of Cr(VI). Equilibrium isotherm, kinetic, and thermodynamic models help to understand Cr(VI)-biochar interactions and their adsorption mechanism. The adsorption studies of Cr(VI) are summarized through the fixed-bed saturated column experiments and Cr-contaminated real groundwater analysis using biochar-based sorbents for practical applicability. This review highlights the significant challenges in biochar-based material applications as green, renewable, and cost-effective adsorbents for the remediation of Cr(VI). Further recommendations and future scope for the implications of advanced novel biochar materials for Cr(VI) removal and other heavy metals are elegantly discussed.

Hexavalent chromium elimination from wastewater by integrated micro-electrolysis composites synthesized from red mud and rice straw via a facile one-pot method

The widely spread chromium (Cr) contamination is rising environmental concerns, while the reutilization of agro-industrial by-products are also urgently demanded due to their potential risks. In this study, we prepared the integrated micro-electrolysis composites (IMC) through a facile one-pot method with red mud and rice straw. The effects of components relatively mass ratios as well as pyrolysis temperature were analyzed. The XRD, XPS, SEM, FTIR, and various techniques proved the IMC was successfully synthesized, which was also used to analyze the reaction mechanisms. In this study, the dosage of IMC, pH, adsorption time, and temperature of adsorption processes were explored, in the adsorption experiment of Cr(VI), dosage of IMC was 2 g/L (pH 6, 25 °C, and 200 rpm) for isothermal, while the concentration and contact time were also varied. According to the batch experiments, IMC exhibited acceptable removal capacity (190.6 mg/g) on Cr(VI) and the efficiency reached 97.74%. The removal mechanisms of adsorbed Cr(VI) were mainly elaborated as chemical reduction, complexation, co-precipitation, and physical adherence. All these results shed light on the facile preparation and agro-industrial by-products recycled as engineering materials for the heavy metals decontamination in wastewater.

Biochar-supported nZVI for the removal of Cr(VI) from soil and water: Advances in experimental research and engineering applications

Over the past decade, biochar-supported nZVI composites (nZVI/biochar) have been developed and applied to treat various pollutants due to their excellent physical and chemical properties, especially in the field of chromium (VI) removal. This paper reviewed the factors influencing the preparation and experiments of nZVI/biochar composites, optimization methods, column experimental studies and the mechanism of Cr(VI) removal. The results showed that the difference in raw materials and preparation temperature led to the difference in functional groups and electron transfer capabilities of nZVI/biochar materials. In the experimental process, pH and test temperature can affect the surface chemical properties of materials and involve the electron transfer efficiency. Elemental doping and microbial coupling can effectively improve the performance of nZVI/biochar composites. In conclusion, biochar can stabilize nZVI and enhance electron transfer in nZVI/biochar materials, enabling the composite materials to remove Cr(VI) efficiently. The study of column experiments provides a theoretical basis for applying nZVI/biochar composites in engineering. Finally, the future work prospects of nZVI/biochar composites for heavy metal removal are introduced, and the main challenges and further research directions are proposed.

Efficient removal of antibiotics from water resources is a public health priority: a critical assessment of the efficacy of some remediation strategies for antibiotics in water

This review discusses the fundamental principles and mechanism of antibiotic removal from water of some commonly applied treatment techniques including chlorination, ozonation, UV-irradiation, Fenton processes, photocatalysis, electrochemical-oxidation, plasma, biochar, anaerobicdigestion, activated carbon and nanomaterials. Some experimental shortfalls identified by researchers such as certain characteristics of degradation agent applied and the strategies explored to override the identified limitations are briefly discussed. Depending on interactions of a range of factors including the type of antibiotic compound, operational parameters applied such as pH, temperature and treatment time, among other factors, all reviewed techniques can eliminate or reduce the levels of antibiotic compounds in water to varying extents. Some of the reviewed techniques such as anaerobic digestion generally require longer treatment times (up to 360, 193 and 170 days, according to some studies), while others such as photocatalysis achieved degradation within short contact time (within a minimum of 30, but up to 60, 240, 300 and 1880 minutes, in some cases). For some treatment techniques such as ozonation and Fenton, it is apparent that subjecting compounds to longer treatment times may improve elimination efficiency, whereas for some other techniques such as nanotechnology, application of longer treatment time generally meant comparatively minimal elimination efficiency. Based on the findings of experimental studies summarized, it is apparent that operational parameters such as pH and treatment time, while critical, do not exert sole or primary influence on the elimination percentage(s) achieved. Elimination efficiency achieved rather seems to be due more to the force of a combination of several factors.

Iron-Doped Biochar Regulated Soil Nickel Adsorption, Wheat Growth, Its Physiology and Elemental Concentration under Contrasting Abiotic Stresses

The prevalence of abiotic stresses hampers soil health and plant growth in most ecosystems. In this study, rice husk iron-enriched biochar (BC) was prepared and its superiority in terms of nutrients enrichment, porosity and different acidic functional group (O-H, C=O) relative to simple biochar was confirmed through scanning electron microscopic, X-ray fluorescence and Fourier transform infrared analysis. To further evaluate its nickel (Ni), salt (NaCl) and carbonate (CaCO3) stress mitigating impact on wheat physiology and biochemical attributes, a pot experiment was conducted using; BC (1%), Ni (0.5 mM NiNO3), Na (100 mM NaCl) and CO3 (100 mM CaCO3) and with twelve treatments; T1; Control, T2; NiNO3, T3; CaCO3, T4; NaCl, T5; BC, T6; Ni + BC, T7; CaCO3 + BC, T8; NaCl + BC, T9; Ni + CaCO3 + BC, T10; Ni + NaCl + BC, T11; CaCO3 + NaCl + BC, T12; Ni + NaCl + CaCO3 + BC. The Langmuir isotherm model revealed the maximum Ni adsorption capacity (2433 mg g−1) in treatments where Ni was applied with BC soil. Maximum soil DTPA-extractable Ni was found in the T9 treatment; however, Ni concentration was not reported in wheat roots while only trace amounts of Ni were found in wheat shoots with the T9 treatment. It was suggested that BC has the capacity to induce the immunization effect in plant roots by providing additional Fe so their ionic homeostasis and redox metabolism worked properly. This argument was further paved by the enhanced adsorption of these toxic ions in the presence of BC-favored wheat growth as indicated by maximum increases in shoot iron and potassium concentrations under Ni + CaCO3 + BC, relative to control. Furthermore, the decrease in shoot hydrogen peroxide (H2O2) (20%) and malondialdehyde (32%) concentrations and increase in shoot ascorbate peroxidase (81%) and catalase (three-fold) activities under Ni + BC relative to Ni + NaCl + CaCO3 + BC controlled the cell membrane damage. In conclusion, BC proved to be an excellent amendment to reduce the toxic effects of Ni, NaCl and CaCO3 stresses and enhance wheat growth and nutrition.

Removal of lead ions (Pb2+) from water and wastewater: a review on the low-cost adsorbents

The presence of lead compounds in the environment is an issue. In particular, supply water consumption has been reported to be a significant source of human exposure to lead compounds, which can pose an elevated risk to humans. Due to its toxicity, the International Agency for Research on Cancer and the US Environmental Protection Agency (USEPA) have classified lead (Pb) and its compounds as probable human carcinogens. The European Community Directive and World Health Organization have set the maximum acceptable lead limits in tap water as 10 µg/L. The USEPA has a guideline value of 15 µg/L in drinking water. Removal of lead ions from water and wastewater is of great importance from regulatory and health perspectives. To date, several hundred publications have been reported on the removal of lead ions from an aqueous solution. This study reviewed the research findings on the low-cost removal of lead ions using different types of adsorbents. The research achievements to date and the limitations were investigated. Different types of adsorbents were compared with respect to adsorption capacity, removal performances, sorbent dose, optimum pH, temperature, initial concentration, and contact time. The best adsorbents and the scopes of improvements were identified. The adsorption capacity of natural materials, industrial byproducts, agricultural waste, forest waste, and biotechnology-based adsorbents were in the ranges of 0.8-333.3 mg/g, 2.5-524.0 mg/g, 0.7-2079 mg/g, 0.4-769.2 mg/g, and 7.6-526.0 mg/g, respectively. The removal efficiency for these adsorbents was in the range of 13.6-100%. Future research to improve these adsorbents might assist in developing low-cost adsorbents for mass-scale applications.

Hierarchically porous biochar templated by in situ formed ZnO for rapid Pb2+ and Cd2+ adsorption in wastewater: Experiment and molecular dynamics study

3D hierarchical porous biochar (HPBC) was synthesized by a thermally removable template without post-activation. Zn(NO₃)₂ decomposition produced gases and ZnO in situ to activate and expand the three-dimensional micro-and mesopores. Compared with pristine biochar (BC), the specific surface area and pore volume of HPBC were increased by 223 and 75 times, respectively. The abundant pore structure of HPBC significantly enhanced the diffusion rate of heavy metals. For example, compared to BC, the time required for HPBC to adsorb Pb²⁺ reach adsorption equilibrium was reduced by 87.5% (40 min vs 5min). Such an adsorption performance of HPBC was also insensitive to different background ions (K⁺, Na⁺, Ca²⁺, and Mg²⁺) with a much higher concentration than that of heavy metals. When applied to treat desulfurization wastewater from power plants, HPBC yielded 100% removal of Pb²⁺ and Cd²⁺, much higher than that by using commercial activated carbon (28%). Molecular dynamics simulation revealed different locations preferred by the adsorption of Pb²⁺ (micropores) and Cd²⁺ (mesopores) in the hierarchical pore structures. The adsorption of Pb²⁺ and Cd²⁺ on HPBC was mainly achieved by diffusion, oxygen functional group complexation, and precipitation. These results provided better knowledge to understand the microscopic adsorption mechanisms of heavy metals in hierarchical pores and a facile yet robust strategy to design such structures in biochar for efficient wastewater treatment.

Mechanistic insights of removing pollutant in adsorption and advanced oxidation processes by sludge biochar

With the accelerated industrialization, more and more sewage sludge (SS) needs to be treated properly. The conversion of sludge into harmless biochar material with dual utilization value of adsorption and catalysis by pyrolysis is in line with the concept of sustainable development. However, the reaction mechanisms of pristine sludge biochar (SDBC) and its composites (SDBCs) in adsorption, persulfate (PS), and Fenton-like advanced oxidation processes (AOPs) are very closely related to its adsorption performance and catalytic efficiency. In this paper, from the application mechanisms of SDBC in adsorption and AOPs, we review in detail the common methods for synthesizing SDBC and their characteristics. We discuss the synthesis techniques that affect the structural, chemical, and catalytic properties of SDBC, including gasification, pyrolysis, and hydrothermal carbonation (HTC). The pyrolysis temperature, environmental factors, and sludge characteristics have important effects on the properties of SDBC, leading to different mechanisms in adsorption and catalytic processes. Furthermore, this paper systematically generalizes the mechanisms of SDBCs in adsorption, where π-π interactions and electrostatic attractions are the main adsorption mechanisms. Then, activation mechanisms of SDBCs in PS and Fenton-like AOPs systems are discussed, including free radical pathways and non-free radical pathways. Finally, we present several challenges and perspectives for the application of SDBC and SDBCs in the field of adsorption, PS, and Fenton-like AOPs from the mechanistic point of views.

Recent advances of carbon-based nano zero valent iron for heavy metals remediation in soil and water: A critical review

Heavy metal pollution in soil and water has presented a new challenge for the environmental remediation technology. Nano zero valent iron (nZVI) has excellent adsorbent properties for heavy metals, and thus, exhibits great potential in environmental remediation. Used as supporting materials for nZVI, carbon-based materials, such as activated carbon (AC), biochar (BC), carbon nanotubes (CNTs), and graphene (GNs) with aromatic rings formed by carbon atoms as the skeleton, have a large specific surface area and porous structure. This paper provides a comprehensive review on the advancement of carbon-based nano zero valent iron (C-nZVI) particles for heavy metal remediation in soil and water. First, different types of carbon-based materials and their combination with nZVI, as well as the synthesis methods and common characterization techniques of C-nZVI, are reviewed. Second, the mechanisms for the interactions between contaminants and C-nZVI, including adsorption, reduction, and oxidation reactions are detailed. Third, the environmental factors affecting the remediation efficiency, such as pH, coexisting constituents, oxygen, contact time, and temperature, are highlighted. Finally, perspectives on the challenges for utilization of C-nZVI in the actual contaminated soil and water and on the long-term efficacy and safety evaluation of C-nZVI have been proposed for further development.

A porous biochar supported nanoscale zero-valent iron material highly efficient for the simultaneous remediation of cadmium and lead contaminated soil

Risk associated with heavy metals in soil has been received widespread attention. In this study, a porous biochar supported nanoscale zero-valent iron (BC-nZVI) was applied to immobilize cadmium (Cd) and lead (Pb) in clayey soil. Experiment results indicated that the immobilization of Cd or Pb by BC-nZVI process was better than that of BC or nZVI process, and about 80% of heavy metals immobilization was obtained in BC-nZVI process. Addition of BC-nZVI could increase soil pH and organic matter (SOM). Cd or Pb immobilization was inhibited with coexisting organic compound 2,4-dichlorophenol (2,4-DCP), but 2,4-DCP could be removed in a simultaneous manner with Cd or Pb immobilization at low concentration levels. Simultaneous immobilization of Cd and Pb was achieved in BC-nZVI process, and both Cd and Pb availability significantly decreased. Stable Cd species inculding Cd(OH)₂, CdCO₃ and CdO were formed, whereas stable Pb species such as PbCO₃, PbO and Pb(OH)₂ were produced with BC-nZVI treatment. Simultaneous immobilization mechanism of Cd and Pb in soil by BC-nZVI was thereby proposed. This study well demonstrates that BC-nZVI has been emerged as a potential technology for the remediation of multiple heavy metals in soil.

The pH-sensitive sorption governed reduction of Cr(VI) by sludge derived biochar and the accelerating effect of organic acids

Reduction coupling immobilization is one of the most commonly adopted strategies for the remediation of Cr(VI) contamination. Biochar is a carbon-rich material with abundant active functional groups for sorption and reduction reactions. In previous reports, phytomass derived biochars and organic functional groups have been emphasized, while the performance of sludge derived biochar (SBC) has often been understated. In the present study, a 30 d kinetic study proved that the removal route involved the sorption of Cr(VI), reduction to Cr(III) and immobilization of Cr(III), and that the sorption process was the primary and rate determining step. As a result of the SBC alkalinity, the solution pH increased, and sorption was largely inhibited, which then governed the overall removal ratio. The FTIR spectra suggested the involvement of hydroxyls in these processes. Low molecular weight organic acids accelerated the removal process in the early phase and improved the reduction process.

An efficient, economical, and easy mass production biochar supported zero-valent iron composite derived from direct-reduction natural goethite for Cu(II) and Cr(VI) remove

In this study, a novel biochar-supported zero-valent iron (ZVI) composite was synthesised by a one-pot co-pyrolysis reduction method, and was used to remove Cu(II) and Cr(VI). The raw materials for the composite were derived from natural bagasse/straw and goethite. Scanning electron microscopy (SEM), X-ray diffraction (XRD) analysis, Fourier-transform infrared (FTIR) spectroscopy, thermogravimetry (TG), and Brunauer-Emmett-Teller (BET) analysis were used to characterise the biochar and biochar-supported ZVI composites. Batch removal experiments on the effects of the initial pH and citric acid concentrations were performed as well as kinetic studies and isotherm experiments. The composite materials showed better Cu(II) and Cr(VI) removal performance than single biochar and mineral. The removal of Cu(II) and Cr(VI) is pH-dependent, and proceeds via heterogeneous multilayer chemisorption. Electrochemical analysis revealed that straw biochar-supported ZVI composite exhibited greater electrical conductivity and electron transfer rate than pure biochar and ZVI. FTIR spectroscopy and X-ray photoelectron spectroscopy (XPS) elucidated the uptake mechanism, showing that Cu(II) and Cr(VI) were easily adsorbed onto the biochar surface and were then reduced by ZVI. These results indicate that biochar-supported ZVI composite is effective for heavy metal remediation, which is economical, environment-friendly, and suitable for mass production.

"In-situ synthesized" iron-based bimetal promotes efficient removal of Cr(VI) in by zero-valent iron-loaded hydroxyapatite

Anionic Cr(VI) and cationic heavy metals generally co-exist in industrial effluents and threaten the public health. Zero-valent iron (ZVI) particles tent to passivate rapidly, which results in a gradual drop in its reactivity. In this work, a strategy of "in-situ synthesized" iron-based bimetal was first developed to stimulate the self-activation of passivated ZVI. During this process, ZVI-loaded hydroxyapatite (ZVI/HAP) was prepared to enhance the affinity for co-existing Cu²⁺, which promoted the in-situ Cu⁰ deposition on ZVI/HAP to form a Fe-Cu bimetal. The deposited Cu⁰ significantly decreased the activation energy (E_a) of Cr(VI) reduction by 24.9%, and its corresponding Cr(VI) removal (96.53%) was much higher that of single Cr(VI) system (68.67%) within 9 h. More importantly, the removal of Cr(VI) and Cu²⁺ were synchronously achieved. Systematical electrochemical characterizations were first introduced to explore the galvanic behaviors of iron-based bimetal. The charge transfer resistance and the negative open circuit potential of ZVI/HAP significantly decreased with the Cu⁰ deposition, thereby accelerating the electron transfer from Fe⁰ to Cu²⁺. The enhanced electron transfer further facilitated the Fe(II) release to promote Cr(VI) reduction. This "in-situ synthesized" iron-based bimetal strategy provides a novel pattern for ZVI activation and exhibits practical application in remediation of combined contaminant.

Efficient Removal of Hexavalent Chromium from an Aquatic System Using Nanoscale Zero-Valent Iron Supported by Ramie Biochar

In this study, ramie biochar (RBC) was used to activate nano zero-valent iron (nZVI) to enhance hexavalent chromium (Cr(VI)) removal. The best results were obtained at a pyrolysis temperature of 600 °C, a biochar particle size of < 150 μm, and an iron to carbon ratio = 1:1. Under the optimal conditions, the removal of Cr(VI) by RBC600-nZVI (98.69%) was much greater than that of RBC600 (12.42%) and nZVI (58.26%). Scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS) revealed that the reaction mechanism at the Fe and Cr interface was a multiple interaction mechanism with reduction dominated, adsorption, and co-precipitation simultaneously. The enhanced performance of RBC600-nZVI resulted from the effective dispersion of nZVI on the surface of RBC600, therefore increasing the adsorption activity sites. At the same time, RBC600 and nZVI exerted a synergistic influence on the composite structure, which jointly promoted the reduction reaction of Cr(VI) and removed more Cr(VI). This study shows that RBC-nZVI is a potentially valuable remediation material that not only provides a new idea for the utilization of ramie waste, but also effectively overcomes the limitations of nZVI, thus, achieving efficient and rapid remediation of Cr(VI).

Synthesis of montmorillonite-supported nano-zero-valent iron via green tea extract: Enhanced transport and application for hexavalent chromium removal from water and soil

The nano-zero-valent iron composite (nZVI@TP-Mont) was successfully prepared using a low-cost and environmental-friendly green synthesis via tea leaves extract (tea polyphenols, TPs) and the montmorillonite (Mont). The batch and column experiments and characterization were conducted to investigate the transport behavior and Cr(VI) remediation by nZVI@TP-Mont in water/soil. Due to its particular surface characteristics and morphology (i.e., the Fe⁰ core wrapped by TPs, the doped sulfur, and interlayer structure), the nZVI@TP-Mont composite showed a great removal capacity of Cr(VI) and sufficient mobility under different soil conditions. We opine the increase in the Cr(VI) reduction of nZVI@TP-Mont was attributed to the tethering of Fe₂O₃ on the surface of Fe⁰ core by the support of Mont interlayer, especially the TP-coverage around nZVI@TP-Mont surface unwrapped, thereby increasing the regenerated reactive Fe²⁺ and the exposed reaction sites of Fe⁰ cores to Cr(VI). The increased transportability of nZVI@TP-Mont slightly depends on the heterogeneous soil properties (i.e., ionic strength, sand/soil ratio, and pH). The two-site kinetic attachment model fitting results suggest Cr(VI)/Cr(III) speciation associated with the agglomerated nZVI@TP-Mont were efficiently immobilized in soil. Therefore, this study would benefit the efficient application of the green-synthesized nZVI@TP-Mont in in-situ remediation of soils contaminated by Cr(VI).

Simultaneous adsorption of Cr(VI) and phenol by biochar-based iron oxide composites in water: Performance, kinetics and mechanism

The pollution of heavy metals and organic compounds has received increased attention in recent years. In the current study, a novel biochar-based iron oxide composite (FeYBC) was successfully synthesized using pomelo peel and ferric chloride solution through one-step process at moderate temperature. Results clearly demonstrate that FeYBC exhibited more efficient removal of Cr(VI) and/or phenol compared with the pristine biochar, and the maximum adsorption amounts of Cr(VI) and phenol by FeYBC could reach 24.37 and 39.32 mg g^-1, respectively. A series of characterization data suggests that several iron oxides such as Fe₂O₃, Fe⁰, FeOOH and Fe₃O₄ were formed on the FeYBC surface as well as oxygen-containing groups. Thermodynamics study indicates that Cr(VI) and phenol adsorption by FeYBC were endothermic and exothermic processes, respectively. Langmuir adsorption isotherm and pseudo-second order models could better explain the Cr(VI) and phenol adsorption behaviors over FeYBC. The Cr(VI) adsorption might be primarily achieved through the ion exchange and surface complexation and reduction, whereas the π-π interaction and electron donor-acceptor complex mainly contributed to phenol adsorption. The findings indicate that the biochar-based iron oxide composites material was an efficient adsorbent for the remediation of industrial effluents containing Cr(VI) and phenol.

Enhancement effect of nanoscale zero-valent iron addition on microbial degradation of BDE-209 in contaminated mangrove sediment

Chemical and biological methods have been employed to remedy polybrominated diphenyl ether contamination, but the removal of decabromodiphenyl ether (BDE-209) by either method still has limitations. The present study aims to evaluate the combined effect of nanoscale zero-valent iron (nZVI) (from 0.1 to 10%) reduction and microbial debromination on BDE-209 removal in mangrove sediments under an anaerobic condition. During the 12-months incubation, nZVI significantly enhanced BDE-209 removal, with 17.03% to 41.99% reduction in sterilized sediments. The reduction was even higher in non-sterilized sediments with living indigenous microorganisms, achieving 15.80%, 33.50%, 55.83% and 66.95% removal of BDE-209 at 0 (control without nZVI), 0.1%, 1% and 10% nZVI, respectively. In control sterilized sediments, no debromination was found, and debromination occurred according to spiked levels of nZVI, with BDE-153 being the dominant congener. The concentrations of debrominated congeners in non-sterilized sediments also increased with nZVI levels, but were significantly higher than the respective sterilized sediment. The relative proportions of different debrominated congeners in non-sterilized sediments depended on nZVI levels, with BDE-99 being the dominant congener in low nZVI amended sediments but shifted to BDE-153 under high nZVI. Higher concentrations of ferrous iron (Fe²⁺) were detected in both sterilized and non-sterilized sediments spiked with more nZVI, and their concentrations significantly correlated with BDE-209 removal. Growth of total bacteria in sediments with 1% and 10% nZVI was inhibited within first two months, but their numbers resumed to that in the control at the end of 12 months. The present study demonstrates the synergy between chemical and microbiological methods, and a combination of nZVI and indigenous microorganisms could be an efficient and feasible mean to remedy BDE-209 in contaminated sediments.

Polysaccharide-based (nano)materials for Cr(VI) removal

Chromium is a potentially poisonous and carcinogenic species, which originates from human activities and various industries such as leather, steel, iron, and electroplating industries. Chromium is present in various oxidation states, among which hexavalent chromium (Cr(VI)) is highly toxic as a natural contaminant. Therefore, chromium, particularly Cr(VI), must be eliminated from the environment, soil, and water to overcome significant problems due to its accumulation in the environment. There are different approaches such as adsorption, ion exchange, photocatalytic reduction, etc. for removing Cr(VI) from the environment. By converting Cr(VI) to Cr(III), its toxicity is reduced. Cr(III) is essential for the human diet, even in small amounts. Today, biopolymers such as alginate, cellulose, gum, pectin, starch, chitin, and chitosan have received much attention for the removal of environmental pollutants. Biopolymers, particularly polysaccharides, are very useful compounds due to their OH and NH₂ functional groups and some advantages such as biodegradability, biocompatibility, and accessibility. Therefore, they can be widely applied in catalytic applications and as efficient adsorbents for the removal of toxic compounds from the environment. This review briefly investigates the application of polysaccharide-based (nano)materials for efficient Cr(VI) removal from the environment using adsorption/reduction, photocatalytic, and chemical reduction mechanisms.

Lead(II) adsorption on microwave-pyrolyzed biochars and hydrochars depends on feedstock type and production temperature

Adsorption of lead(II) using carbon-rich chars is an environmentally sustainable approach to remediate lead(II) pollution in industrial wastewater. We studied mechanisms for lead(II) adsorption from synthetic wastewater by biochars produced by microwave-assisted pyrolysis and hydrochars by hydrothermal carbonization at three temperatures using four feedstocks. Lead(II) adsorption was highest (165 mg g^-1) for canola straw biochar produced at 500 °C. Except for chars derived from sawdust, biochars outperformed hydrochars for lead(II) adsorption due to changes in solution pH driven by char pH. As char production temperature increased, lead(II) adsorption decreased in hydrochar mainly due to interaction with aromatic carbon but increased in biochar due to precipitation as hydrocerussite and lead oxide phosphate. Lead(II) adsorption also occurred via surface complexation and cation-ᴨ interaction, as the data fitted well to Freundlich, Langmuir and Temkin models, and the pseudo-first and pseudo-second order kinetic models, depending on feedstock type and production temperature. More than 80% of lead(II) adsorption occurred in the first 3 h for both types of chars; with a few exceptions, adsorption continued for almost 24 h. We conclude that production method, production temperature and feedstock type are crucial factors to consider in designing chars as adsorbents for removing lead(II) from wastewater.

Vitamin C mediates the activation of green tea extract to modify nanozero-valent iron composites: Enhanced transport in heterogeneous porous media and the removal of hexavalent chromium

Both green tea (GT) extract and vitamin C (VC) were used for the reduction of Fe³⁺ to Fe⁰ using a green synthesis method. Modified nanozero-valent iron (GT-nZVI@VC nanocomposites) was successfully obtained and characterized as α-Fe⁰-iron oxide/VC by multiple analytical methods. The GT-nZVI@VC nanocomposites showed better transportability than nZVI, in that transport behavior was slightly dependent on various ratios of sand/soil in water-saturated heterogeneous porous media. Breakthrough curves of GT-nZVI@VC nanocomposites in paddy soil exhibited "blocking effects" and were well described using a first-order straining coefficient (k₂) on site 2 obtained from a two-site kinetic attachment model. In particular, GT-nZVI@VC (VC/Fe = 0.6) showed higher Cr(VI) removal (especially reducibility) in both paddy soil and water compared to that of nZVI and VC. It is likely that the synergistic effects of VC (ascorbic acid) and tea polyphenols can increase the released free electrons into solution, favoring the high reduction of Cr(VI) into Cr(III) (i.e., FeOCr₂O₃, Cr(OH)₃ and Cr₂O₃), where Cr(III) is prone to be immobilized by the nanocomposites in soil. This research highlights that VC can mediate the activation of GT extract to successfully modify nZVI, which could be beneficial for efficient transport in subsurface and remediation of Cr(VI)-contaminated soil and underground water.

Re-recognizing micro locations of nanoscale zero-valent iron in biochar using C-TEM technique

Biochar supported nanoscale zero-valent iron (NZVI/BC), prepared commonly by liquid reduction using sodium borohydride (NaBH₄), exhibits better reduction performance for contaminants than bare NZVI. The better reducing ability was attributed to attachment of nanoscale zero-valent iron (NZVI) on biochar (BC) surface or into the interior pores of BC particles due to observations by scanning electron microscopy (SEM) and plan transmission electron microscopy (P-TEM) techniques in previous studies. In this study, cross-sectional TEM (C-TEM) technique was employed firstly to explore location of NZVI in NZVI/BC. It was observed that NZVI is isolated from BC particles, but not located on the surface or in the interior pores of BC particles. This observation was also supported by negligible adsorption and precipitation of Fe²⁺/Fe³⁺ and iron hydroxides on BC surface or into interior pores of BC particles respectively. Precipitation of Fe²⁺ and Fe³⁺, rather than adsorption, is responsible for the removal of Fe²⁺ and Fe³⁺ by BC. Moreover, precipitates of iron hydroxides cannot be reduced to NZVI by NaBH₄. In addition to SEM or P-TEM, therefore, C-TEM is a potential technique to characterize the interior morphology of NZVI/BC for better understanding the improved reduction performance of contaminants by NZVI/BC than bare NZVI.

Preparation of biochar and biochar composites and their application in a Fenton-like process for wastewater decontamination: A review

Biochar is a carbon-rich material that can be obtained from pyrolysis of solid waste (e.g., agricultural solid waste and sludge from wastewater treatment plants). Biochar features low cost, large specific surface area, and strong adsorption capacity. New biochar composites can be produced via modification and loading of nano particles onto biochar. Biochar can contribute to the dispersion and stabilization of nano particles. In addition, nano particles can increase the number of surface-active sites, which improves the physicochemical properties of the material. Biochar and biochar composites have been applied widely in wastewater treatment, and have significantly enhanced the treatment performance of Fenton-like processes (activation of hydrogen peroxide and persulfate) as an advanced oxidation process for organics removal and wastewater decontamination. This paper reviews the preparation methods for biochar and biochar composites to systematically analyze the influential factors on the preparation process. The paper also comprehensively reviews the mechanisms by which biochar removes different organic pollutants. However, due to the vast number of different biochar feedstocks and their preparation methods, it is difficult to compare the properties of one biochar to another. Guidance if provided for the application of biochar and biochar composites for wastewater decontamination.

FeS2 assisted degradation of atrazine by bentonite-supported nZVI coupling with hydrogen peroxide process in water: Performance and mechanism

In this study, bentonite-supported nZVI (B-nZVI) was used as a catalyst to activate H₂O₂ for atrazine (ATZ) degradation in the presence of FeS₂. Results indicated that ATZ degradation by B-nZVI/H₂O₂ process was significantly enhanced when FeS₂ was introduced, and nearly 98% of ATZ was degraded by B-nZVI/FeS₂/H₂O₂ process within 60 min under the optimum conditions. ATZ degradation of B-nZVI/FeS₂/H₂O₂ process was much higher than the sum of B-nZVI and FeS₂/H₂O₂ processes. The presence of HCO₃^-, PO₄^3- and F^- exhibited significant negative effects on the ATZ degradation, whereas both Cu²⁺ and Ni²⁺ exhibited positive effects on that. Both citric acid (CA) and ethylenediaminetetraacetic acid (EDTA) with lower concentration enhanced ATZ degradation rate, but significant suppression effects on that with higher concentration. The degradation of ATZ and 2,4-Dichlorophenol (2,4-DCP) could be simultaneously achieved in B-nZVI/FeS₂/H₂O₂ process under certain conditions. High soluble Fe²⁺ induced an excellent decomposition of H₂O₂ by B-nZVI and FeS₂. OH was dominant radical, and contributed to nearly 86% of the overall ATZ removal. A total of five intermediate products of ATZ were identified, and ATZ degradation was achieved via de-alkylation and hydroxylation processes. An enhanced reaction mechanism for ATZ degradation by B-nZVI/FeS₂/H₂O₂ process was proposed, and B-nZVI/FeS₂/H₂O₂ process exhibited an excellect catalytic performance within four successive runs.