Synergistically enhancing Fenton-like degradation of organics by in situ transformation from Fe3O4 microspheres to mesoporous Fe, N-dual doped carbon

Singlet oxygen: Properties, generation, detection, and environmental applications

Singlet oxygen (1O2) is molecular oxygen in the excited state with high energy and electrophilic properties. It is widely found in nature, and its important role is gradually extending from chemical syntheses and medical techniques to environmental remediation. However, there exist ambiguities and controversies regarding detection methods, generation pathways, and reaction mechanisms which have hindered the understanding and applications of 1O2. For example, the inaccurate detection of 1O2 has led to an overestimation of its role in pollutant degradation. The difficulty in detecting multiple intermediate species obscures the mechanism of 1O2 production. The applications of 1O2 in environmental remediation have also not been comprehensively commented on. To fill these knowledge gaps, this paper systematically discussed the properties and generation of 1O2, reviewed the state-of-the-art detection methods for 1O2 and long-standing controversies in the catalytic systems. Future opportunities and challenges were also discussed regarding the applications of 1O2 in the degradation of pollutants dissolved in water and volatilized in the atmosphere, the disinfection of drinking water, the gas/solid sterilization, and the self-cleaning of filter membranes. This review is expected to provide a better understanding of 1O2-based advanced oxidation processes and practical applications in the environmental protection of 1O2.

Preparation of N-doped porous biochar with high specific surface area and its efficient adsorption for mercury ion from aqueous solution

Herein, a new type of super active nitrogen-doped biochar sheet (SNBC) was prepared by two-step pyrolysis and KOH chemical activation with melamine and cherry kernel powder as precursors of nitrogen and carbon source for removing Hg2+ from wastewater. The N2 adsorption/desorption and scanning electron microscope characterization revealed that the resulted SNBC under 600 °C calcination owned huge specific surface area of 2828 m2/g and plenty of well-developed micropores, and X-ray photoelectron spectroscopy and Fourier transform-infrared spectroscopy analysis testified the existence of functional groups containing N and O, which could provide adsorption sites for Hg2+. The SNBC-600 showed high adsorption capacity for Hg2+ even at low pH, and interfering cations had little effect on the adsorption. The adsorption process was rapid and dynamic data fit the pseudo-second-order dynamic model well. The maximum adsorption capacity of Hg2+ on SNBC-600 calculated by Langmuir model was 230 mg/g. After six times of reuse, the adsorption capacity still exceeded 200 mg/g, exhibiting good reusability. The designed microfiltration membrane device base on SNBC-600 could remove low concentration of Hg2+ effectively from solution. This study provided a simple and environment-friendly method for manufacturing nitrogen-doped biochar sheet, which was of great significance in the practical application of Hg2+ pollution treatment.

Fe2O3/TiO2/reduced graphene oxide-driven recycled visible-photocatalytic Fenton reactions to mineralize organic pollutants in a wide pH range

Photocatalytic Fenton reactions combined the advantages from both photocatalysis and Fenton reaction in mineralizing organic pollutants. The key problems are the efficiency and recycling stability. Herein, we reported a novel Fe2O3/TiO2/reduced graphene oxide (FTG) nanocomposite synthesized by a facile solvothermal method. The TiO2 in FTG degraded organic pollutants and mineralized intermediates via photocatalysis under visible light irradiation, which could also promote Fenton reaction by accelerating Fe3+-Fe2+ recycle. Meanwhile, the Fe2O3 rapidly degraded organic pollutants via Fenton reactions, which also promoted photocatalysis by enhancing visible light absorbance and diminishing photoelectron-hole recombination. The high distribution of TiO2 and Fe2O3 on rGO, together with their strong interaction resulted in enhanced synergetic cooperation between photocatalysis and Fenton reactions, leading to the high mineralization efficiency of organic pollutants. More importantly, it could also inhibit the leaching of Fe species, leading to the long lifetime of FTG during photocatalytic Fenton reactions in a wide pH range from 3.4 to 9.2.

Photo-assisted degradation of Rhodamine B by a heterogeneous Fenton-like process: performance and kinetics

This study presents the degradation of rhodamine B (RhB) by photo Fenton-like (PF-like) process under visible light irradiation (λ > 380 nm) using cobalt phosphate microparticles (CoP-MPs). The effects of the initial concentration of RhB, pH value, CoP-MPs dosage, hydrogen peroxide (H2O2) concentration, and salts found in textile wastewater (such as NaNO3, Na2SO4, and NaCl) were investigated in detail. It was found that CoP-MPs can maintain high catalytic activity with wide pH values varying from 4 to 8. This indicated that the use of CoP-MPs overcame the low efficiency of Fenton-like reaction at neutral and even weakly alkaline pH. The PF-like degradation of RhB followed pseudo-first order kinetics in various conditions. Moreover, a comparison of experimental results showed that the PF-like system has good degradation ability for RhB and methyl blue (MB) solution, but is poor for methyl orange (MO) solution. The repeat experiments indicated that the chemical structures of CoP-MPs were stable. Furthermore, the Co2+ ions leaching to the solutions were measured by an inductively coupled plasma mass spectrometer (ICP-MS). Analysis of UV-vis spectra suggested that RhB was degraded by the formation of a series of N-de-ethylated intermediates followed by cleavage of the whole conjugate chromophore structure.HighlightsRhB can be effectively degraded in the PF-like process under visible light irradiation by CoP-MPs.The PF-like process can maintain high catalytic activity at neutral and even weakly alkaline pH.Degradation kinetics exhibited pseudo-first-order kinetics and were influenced by the key parameters.The variation in the UV-vis spectra of RhB was analyzed in detail to infer a possible degradation pathway.

Fe(VI) activation system mediated by a solar-driven TiO2 nanotubes electrode for CLQ degradation: Performances, mechanisms and pathways

Ferrate (Fe(VI), FeO₄^2-) has been widely used in the degradation of micropollutants with the advantages of high redox potential, no secondary pollution and inhibition of disinfection byproducts. However, the low transformation of Fe(V) and/or Fe(IV) by Fe(VI) and incomplete mineralization of pollutants limit their application. In this work, we designed a photo electric cell with TiO₂ nanotubes (TNTs) and Pt serving as the anode and cathode to enhance the utilization of Fe(VI) (Fe(VI)-TNTs system). TNTs accelerated the generation of •OH via h_VB⁺ oxidation of OH^- and photogenerated electrons at Pt boosted the transformation of Fe(VI) to Fe(V) and/or Fe(IV), resulting in a 22.2 % enhancement of chloroquine (CLQ) removal compared to Fe(VI) alone. The results from EPR and quenching tests showed that Fe(VI), Fe(V), Fe(IV), •OH, O₂^•- and h_VB⁺ coexisted in the Fe(VI)-TNTs system, among which Fe(V) and Fe(IV) were testified as the primary reactive substances accounting for 59 % of CLQ removal. The performance tests and recycling tests demonstrated that the Fe(VI)-TNTs system maintained excellent performance in an authentic water environment. The plausible degradation pathway of CLQ oxidized in the Fe(VI)-TNTs system was proposed with nine identified oxidation products via N-C cleavage, electrophilic addition and carboxylation processes. Based on the ECOSAR calculation, the constructed reaction system allowed a decrease in acute and chronic toxicity. Our findings provide a highly efficient and cost-effective strategy to enhance Fe(VI) application for micropollutant degradation in the future.

Highly-efficient peroxydisulfate activation by polyaniline-polypyrrole copolymers derived pyrolytic carbon for 2,4-dichlorophenol removal in water: Coupling mechanism of singlet oxygen and electron transfer

Carbonization of N-containing aromatic polymers is a promising route to prepare N-doped carbon materials with low cost, easy regulation, and no external N source. However, there are relatively few studies applying these materials for persulfate activation, and the catalytic mechanisms of the existing reaction systems are divergent. In this paper, a series of N-doped carbon materials were prepared by carbonizing polyaniline (PANI), polypyrrole (PPy), and PANI-PPy copolymers. The copolymer-derived carbon materials exhibit superior peroxydisulfate (PDS) catalytic activity compared to some commercially available and reported carbon materials. Combing quenching experiments, EPR analysis, chemical probe analysis, and various electrochemical analysis methods identified the singlet oxygen (¹O₂) and electron transfer as the main reaction pathways of all systems, but the contribution of each pathway was influenced by the types of precursors. The structure-activity relationship indicated that the carbonyl group (CO) was the main active site for the ¹O₂ pathway, while the electron transfer ability of the reaction system and the potential of the complex formed by catalyst and PDS jointly determined the electron transfer pathway. This paper provides a new strategy for obtaining excellent N-doped carbon-based persulfate activators and deepens the insight into the mechanism of PDS activation by N-doped carbon materials.

Magnetic Co/CoOx@NCNT catalysts for activation of potassium peroxymonosulfate to deteriorate phenol from wastewater

Phenols are of much toxicological and they must be effectively removed from the wastewater from industries as well as sewage treatment. Such removal demands a special and strong composite. So, this piece of research aims to activate Potassium peroxymonosulfate (PPMS) with the large surface area of magnetite nitrogen-fixed porous carbon nanotube composites (Co/CoOx@NCNT). Increases in the graphitization degree and structural control brought about by the incorporation of reduced Graphite oxide (rGO) significantly increased the catalyst activity of Co/CoOx@NCNT. It was found that PPMS activation for phenol removal by Co/CoOx@NCNT was nearly as effective as by homogeneous Co²⁺, with nearly 100% removal efficiency in 10 min. Both high reusability and high recycling of Co/CoOx@NCNT were accomplished simultaneously by proving the technology of viability in practical applications. The PPMS activation mechanism in the Co/CoOx@NCNT/PPMS system was driven by the electron transmission from contaminants to PPMS through the sp^2- hybrid carbon nanotubes and nitrogen system. The selectivity of the Co/CoOx@NCNT/PPMS system to remove diverse organic compounds was determined by batch experiments. Due to the insignificant impact of radicals reactive on pollutant breakdown, the ability to inhibit species (such as Cl^- and natural organic materials) from a minor role was significantly decreased. These results not only shed light on the process of PPMS heterogeneous activation but also provided a framework for the balanced project of highly effective nanocarbon-based catalysts for PPMS activation.

New insights into the degradation and detoxification of methylene blue using heterogeneous-Fenton catalyzed by sustainable siderite

The huge application of synthetic dyes caused a severe impact in the environment. In the present study, a physico-chemical strategy of heterogeneous-Fenton catalyzed by the natural ferrous ore has been established for toxic chemical degradation, of which the complex and high-expense repetitive pH adjustment procedures were escaping. And this natural heterogeneous catalyst also could be recycled and sustainable for toxic substances treatment involved in synergetic adsorption and oxidation. The siderite, served as an adsorbent and catalyst for the degradation of methylene blue (MB). Siderite exhibited a better adsorption capacity with a saturated adsorption capacity of ∼11.08 mg/g. Batch adsorption experiments have verified that adsorption rate and adsorption equilibrium followed pseudo-second-order rate model and Langmuir isotherm equation, respectively. The combination with H₂O₂, showed significant enhancement of MB degradation without any pH adjustment. The effect of siderite dosage, H₂O₂ dosage, MB concentration, initial pH, and reaction temperature on MB degradation was investigated, which also has indicated the excellent catalytic performance of siderite. About 99.71% of MB was degraded in 480 min with initial pH of 7.0, reaction temperature of 25 °C, siderite, and H₂O₂ dosage of 2.5 g/L and 122.38 mM, respectively. It was found that siderite could be reused and remained high degradation efficiency on MB after 5 times reutilization, which also could demonstrate the sustainable and effective process to degrade organic pollution. The generation of reactive species including ·OH and O2·- have been confirmed based on scavenger test and electron spin resonance (ESR) analysis, which was dominated by heterogeneous reaction. The possible degradation mechanisms of MB have been predicted based on spectrum scanning and GC-MS analysis. Moreover, acute toxicity assessment with marine photobacterium Vibrio fisheri was conducted to investigate the toxicity change in the adsorption/oxidation coupled process. This sustainable heterogeneous-Fenton technology has been verified as a promising and applicable process for toxic organic chemicals removal due to effective mineralization and detoxification assisted with the natural ore mineral through the simple operation and mild condtions.

Efficient activation of persulfate by Nickel-supported cherry core biochar composite for removal of bisphenol A

In this study, low-cost and easily obtained biochar was chosen to prepare nickel-modified biochar materials (Ni/BC) through a one-step activation pyrolysis method. Characterization with X-ray diffraction, X-ray photoelectron spectroscopy and high-resolution transmission electron microscopy proved the existence of Ni⁰ and NiO nanocrystals in Ni/BC catalyst. The optimal Ni_0.5/BC exhibited excellent peroxymonosulfate (PMS) and peroxydisulfate (PDS) activation efficiency toward bisphenol A (BPA) degradation. The Ni_0.5/BC (0.03 g) reacted with 1.0 g L^-1 PMS or PDS could completely remove 20 mg L^-1 BPA in 10 min with the first-order kinetic constants (k₁) of 0.322 min^-1 (PMS) and 0.336 min^-1 (PDS). More importantly, the composite has better structural and functional attributes for the BPA degradation with universal applicability at wide pH and temperature range, proving as a better degradation mediator with high adaptation for numerous organic pollutants. Catalytic activity decreased slightly even after 4 cycles. Based on the quenching experiment and electron paramagnetic resonance, it was found that SO₄^•-, •OH and ¹O₂ were the dominant active species in BPA degradation process. Therefore, this work not only supplies a promising catalyst for the removal of organic contaminants, but also is beneficial for the further development of alternative catalysts for sulfate radical based advanced oxidation processes.

A ZIF-8-derived copper-nitrogen co-hybrid carbon catalyst for peroxymonosulfate activation to degrade BPA

A series of copper-nitrogen co-hybrid porous carbon catalysts were prepared by pyrolysis of copper-doped ZIF-8 in argon atmosphere. Both the precursors and the corresponding pyrolysis products retained the polyhedral morphology of ZIF-8. The catalytic performance of the catalysts obtained at different Cu doping levels and pyrolysis temperatures for PMS activation was compared by bisphenol A (BPA) degradation experiment. Among them 5%Cu-NC(8) catalyst obtained by pyrolysis of 5%Cu-ZIF-8 at 950 °C showed the best catalytic performance. The catalytic mechanism of PMS activation catalyzed by 5%Cu-NC(8) was analyzed by quenching experiment, ESR and XPS. The degradation pathways of BPA in 5%Cu-NC(8)/PMS system were proposed on the basis of LC-MS analyses. Pyridine N (including Cu-N), graphite N, CO group and the valence change of Cu were recognized as the catalytic active sites for 5%Cu-NC(8). Both free radical and non-free radical processes were involved in BPA degradation, and singlet oxygen (¹O₂) was identified to be the main active substance. The stable performance and low Cu leaching rate in recycling experiment indicated that 5%Cu-NC(8) had good reusability and stability. This study provided a new insight for the design of heterogeneous copper-nitrogen co-hybrid carbon catalysts.

Synergistic role of inherent calcium and iron minerals in paper mill sludge biochar for phosphate adsorption

Phosphate adsorption using metal-based biochar has awakened much attention and triggered extensive research. In this study, novel Ca/Fe-rich biochars were prepared via a one-step process of pyrolyzing paper mill sludge (PMS) at various temperatures (300, 500, 700, and 800 °C) under a CO₂ atmosphere for phosphate removal. Batch adsorption experiments showed that the biochar obtained at 800 °C (PB-800), which could be easily separated magnetically, exhibited the best phosphate adsorption capacity in a wide range of solution pH (5-11). Based on the Langmuir model, the maximum phosphate adsorption capacity for PB-800 was 17.33 mg/g. Besides, the effects of ambient temperature as well as coexisting ions on phosphate removal were also investigated. Kinetic and thermodynamic analysis revealed that chemisorption dominated the adsorption process. The calcium carbonate and ferric salts in the sludge were converted into CaO and Fe₃O₄ through pyrolysis at 800 °C. The CaO inherent in PB-800 was proved to serve as active sites for the chemical precipitation, showing its synergistic effect with iron oxide compounds (i.e., Fe₃O₄, α-Fe₂O₃) on phosphate removal through chemical precipitation, ligand exchange, and complexation. This study not only provides a feasible waste-to-wealth strategy for converting PMS into a Ca/Fe-rich magnetic biochar that can be used as an effective phosphate adsorbent, but also offers new insights into the synergistic effect of calcium and iron species for the adsorption of phosphate using biochar.

High efficiency degradation of tetracycline by peroxymonosulfate activated with Fe/NC catalysts: Performance, intermediates, stability and mechanism

Carbon-based catalysts have the advantages of biological cleaning, eco-friendly and cost-effective in water treatment. While, nitrogen doped biochar promotes the development of non-radical peroxymonosulfate (PMS) activation in environmental remediation. Thus, three-dimensional sponge-like porous Fe and N co-doped biochar (Fe/CN-30) with high catalytic activity for PMS activation was synthesized. In a wide pH range (1-11), the Fe/CN-30 catalyst can efficiently degrade tetracycline (TC) with a small amount of PMS. The non-radical pathways are prominent in the TC decomposition process according to the quenching experiments, electron paramagnetic resonance (EPR) and gas chromatograph-mass spectrometer (GC-MS) analysis, in which the contribution of high-valent iron-oxo species (Fe(IV) = O) was dominant. X-ray photoelectron spectroscopy and reaction kinetic experiments confirmed that the coordination sites of Fe and N in the Fe/CN-30 are the reactive centers for TC degradation. Moreover, the successive addition of low concentration PMS into the system was confirmed to favor the PMS utilization, and the high selectivity of the Fe/CN-30 was confirmed by the analysis of pollutant structure. Furthermore, by-products of TC degradation in the Fe/CN-30/PMS system and the possible TC degradation pathways were proposed via liquid chromatography-mass spectrometry (LC-MS). Therefore, this study dedicates to providing new insights into the non-radical pathway-catalyzed AOPs.

Cobalt-loaded cherry core biochar composite as an effective heterogeneous persulfate catalyst for bisphenol A degradation

Persulfate (PS)-based advanced oxidation processes have drawn tremendous attention for the degradation of recalcitrant pollutants, and cobalt composites are effective for PS activation to generate reactive species. In this study, composites of cobalt species loaded on cherry core-derived biochar (Co/C) were prepared with a one-step pyrolysis method. The Co/C catalyst was applied as a catalyst for PS activation to degrade bisphenol A (BPA). Factors influencing the degradation efficiency were examined, including the ratio of raw materials, Co/C and PS dosages, temperature, and solution pH. The Co/C catalyst prepared when the ratio of raw material was 1 : 1 (Co/C-50) could efficiently activate both peroxymonosulfate (PMS) and peroxydisulfate (PDS). When the initial concentration of BPA was 20 mg L-1, complete removal of BPA was achieved in the Co/C-50-PMS and Co/C-50-PDS systems within 8 min and 10 min, respectively. More than 70% of BPA could be mineralized in the Co/C-50-PS system. The free radical quenching experiments demonstrated that in the Co/C-50-PS system, the degradation of BPA was achieved through free radical, surface-bound free radical, and non-free radical pathways. The successful preparation of the Co/C-50-PS catalyst broadens the application of cobalt-based carbon materials in the activation of PS to remove organic pollutants.

Atomically dispersed Fe/Bi dual active sites single-atom nanozymes for cascade catalysis and peroxymonosulfate activation to degrade dyes

Constructing single-atom nanozymes (SAzymes) with densely exposed and dispersed double metal-N_x catalytic sites for pollution remediation remains rare and challenging. Herein, we report a novel Fe-Bi bimetallic MOF-derived carbon supported Fe-N₄ and Bi-N₄ dual-site FeBi-NC SAzyme for cascade catalysis and peroxymonosulfate activation to degrade dye pollutants, which is synthesized from the Fe-doped Bi-MOF as a precursor. The formation of both Fe-N₄ and Bi-N₄ sites is demonstrated by XANES and EXAFS. The FeBi-NC SAzyme has high single atoms loadings of Fe (2.61 wt%) and Bi (8.01 wt%), and displays 5.9- and 9.8-fold oxidase mimicking activity enhancement relative to the Fe-NC and Bi-NC SAzymes, respectively. When integrated acetylcholinesterase (AChE) and FeBi-NC SAzyme, a cascade enzyme-nanozyme system is developed for selective and sensitive screening of AChE activity with a low detection limit of 1 × 10^-4 mU mL^-1. Both Fe-N₄ and Bi-N₄ in FeBi-NC display a strong binding energy and electron donating capability to promote peroxymonosulfate activation to generate highly active intermediates for rhodamine B degradation. 100% rhodamine B removal occurs within 5 min via FeBi-NC mediated activation of peroxymonosulfate. The DFT calculations reveal that high activity of FeBi-NC is due to the isolated Fe-N₄ and Bi-N₄ sites and their synergy.

One-step pyrolysis for preparation of sulfur-doped biochar loaded with iron nanoparticles as an effective peroxymonosulfate activator for RhB degradation

In this study, sulfur-doped biochar loaded with iron nanoparticles (Fe/S-BC) was easily prepared by a one-pot pyrolysis method using anhydrous FeCl3, Na2S2O3·5H2O, and cherry stone powder as raw materials and...

Regulation of electronic structures of MOF-derived carbon via ligand adjustment for enhanced Fenton-like reactions

Peroxymonosulfate (PMS)-based Fenton-like reactions are widely used for wastewater remediation. Metal-free carbonaceous activators can avoid the secondary pollution caused by metal leaching but often suffer from insufficient activity due to limited active centers and mass transfer barriers. Here, we prepared a series of heteroatom (N, S, F)-doped, highly porous carbonaceous materials (UC-X, X = N, S, F) by pyrolyzing UiO-66 precursors assembled by various organic ligands. Density functional theory calculations showed that the heteroatoms modulated the electronic structures of the carbon plane. UC-X exhibited significantly enhanced PMS activation capability compared with the undoped counterpart, in the efficiency order of UC-N > UC-S > UC-F > UC. UC-N (calcined at 1000°C) showed the best PMS activation, exceeding that of commonly used carbocatalysts. The prominent performance of UC-N originated from its unique porous structure and homogeneously dispersed graphitic N moieties. Trapping experiments and electron spin resonance showed a nonradical degradation pathway in the UC-N/PMS system, through which organics were oxidized by donating electrons to UC-N/PMS* metastable complexes. This work not only reports a universal way to access high-performance, metal-free PMS activators but also provides insight into the underlying mechanism of the carbon-activated PMS process.

Development of a hydroxyl group-mediated biosynthetic schwertmannite as a persulfate activator for efficient degradation of RhB and Cr(VI) removal

Recently, sulfate radical-based advanced oxidation processes (SR-AOPs) have shown broad potential for restoring the water environment. However, the application of SR-AOPs to simultaneously remove organic pollutants and Cr(VI) has rarely been reported. Herein, we developed a modified schwertmannite (Sch-PVA) synthesized via the mediation of Acidithiobacillus ferrooxidans in the introduction of polyvinyl alcohol (PVA). This modification significantly changed the morphology and structure of the schwertmannite (Sch). The specific surface area and the density of functional sites also increased. Sch-PVA significantly increased the persulfate (PDS) activation efficiency. Even in 100 mg L^-1 rhodamine B (RhB) conditions, 96.3% of RhB was eliminated by 0.5 g L^-1Sch-PVA and 6 mM PDS in 120 min. Moreover, excellent performance was exhibited over a wide pH range. The dissolution of the passivation layer facilitated the exposure of new adsorption and reduction sites, thereby enhancing the simultaneous removal of RhB and Cr(VI). Quenching experiments and electron spin resonance (ESR) measurements verified that sulfate and hydroxyl radicals were generated. The hydroxyl groups on the Sch-PVA surface played a key role in the bonding with and the activation of PDS. In conclusion, Sch-PVA provides new insights into the catalyst application for simultaneous removal of organic pollutants and Cr(VI).

One-step synthesis of mixed valence FeOX nanoparticles supported on biomass activated carbon for degradation of bisphenol A by activating peroxydisulfate

A novel FeO_X nanoparticles supported biomass activated carbon (BAC/FeO_X) composite was prepared through one-pot calcination method with FeCl₃ and cherry stone powder as precursors. The carbonization of biomass, reduction of Fe³⁺, and FeO_X anchored on carbon substrate could be achieved at the same time. Characterization with transmission electron microscope (TEM) and scanning electron microscope indicated that nanoscale FeO_X distributed uniformly on carbon substrate, and X-ray photoelectron spectroscopy, X-ray diffraction, and high resolution TEM characterization proved that the loaded FeO_X was high crystallinity of Fe₃O₄ and α-Fe⁰. Bisphenol A (BPA) was used to investigate the degradation performance of BAC/FeO_X activating peroxydisulfate (PDS). The ratio of raw materials affected degradation efficiency of BPA intensively through the content, valence state, and dispersibility of FeO_X nanoparticles, and the optimal material could degrade 20 mg/L BPA completely in 5 min at 0.1 g/L in the presence of 1 g/L PDS. Free radical determination and quenching experiments indicated that both SO₄^•- and •OH were involved in BPA degradation. The degradation pathway was proposed based on the identification of degradation intermediates. The facile synthesis method, high activation efficiency, and low-cost and environmental friendly raw materials made the BAC/FeO_X-50 an alternative catalyst for organic pollution water treatment.

Synergistically enhanced heterogeneous activation of persulfate for aqueous carbamazepine degradation using Fe3O4@SBA-15

The exploration of low-cost, high-performance and stable catalytic materials for sulfate radical-based advanced oxidation processes (SR-AOPs) is of great importance. This study presents Fe₃O₄-wrapped SBA-15 mesoporous silica catalyst (Fe₃O₄@SBA-15) for persulfate (PS) activation. The Fe₃O₄@SBA-15 with an Fe₃O₄ to SBA-15 weight ratio of 3:1 exhibited an impressive carbamazepine (CBZ) removal efficiency of ~100% after 30 min of SR-AOP at an initial pH of 3.0, a temperature of 25 °C, an initial PS concentration of 300 mg L^-1 and a catalyst concentration of 0.50 g L^-1. The primary oxidizing species produced in the system were identified as SO₄^- and HO by electron paramagnetic resonance spectra and radical quenching experiments. Benefiting from the synergetic effects of improved Fe₃O₄ dispersion and enhanced adsorption of CBZ and PS by SBA-15, the as-obtained heterogeneous Fe₃O₄@SBA-15 catalysts offer large numbers of active sites for free radical generation and high surface concentrations of CBZ and PS for SR-AOPs, as verified by physicochemical characterization and Langmuir-Hinshelwood model analysis. In addition, the activity of Fe₃O₄@SBA-15 was maintained throughout six successive cycling tests. Various inorganic anions, including Cl^-, NO₃^-, HCO₃^-, and CO₃^2-, as well as organic material in natural water, exert a negative impact on the Fe₃O₄@SBA-15 catalyzed SR-AOPs and deserve special attention.

ZIF-8 derived Fe‒N coordination moieties anchored carbon nanocubes for efficient peroxymonosulfate activation via non-radical pathways: Role of FeNx sites

Developing high-efficient hybrids carbon catalysts for PMS-based advanced oxidation process (AOPs) are crucial in the field of environmental remediation. In this work, novel carbon nanocubes (xFe‒N‒C) with three-dimensional porous structure and abundant well-dispersed FeN_x sites were obtained via a skillful cage-encapsulated-precursor pyrolysis strategy. The as-synthesized xFe‒N‒C exhibited superb activity for phenol degradation by activating peroxymonosulfate (PMS). Besides, the catalytic system not only possessed good recycling performance, wide pH adaptation and relatively low activation energy, but also had high resistance to environmental interference. Singlet oxygen (¹O₂) dominated non-radical process was responsible for phenol degradation rather than traditional radical pathways. Impressively, the doping level of Fe could regulate FeN_x contents in catalysts, and the catalytic activity of xFe‒N‒C was greatly enhanced with increasing FeN_x contents. Based on density functional theory calculations (DFT), the introduction of FeN_x sites regulated the electronic structure of catalysts. Such electron-deficient Fe center acted as electron acceptor to receive electrons transmitted by the adsorbed PMS, thus generating highly reactive ¹O₂ for rapid phenol oxidation. This work provides a new insight into the innovation in transition metal-nitrogen hybrid carbon catalysts and highlights the pivotal roles of FeN_x sites in ¹O₂ generation during PMS activation process.

Single-atom catalysis in advanced oxidation processes for environmental remediation

This review presents the recent advances in synthetic strategies, characterisation, and computations of carbon-based single-atom catalysts, as well as their innovative applications and mechanisms in advanced oxidation technologies.

One-Step Synthesis of Metal-Modified Nanomagnetic Materials and Their Application in the Removal of Chlortetracycline

Magnetic nanomaterials are promising heterogeneous catalysts for environmental applications. According to X-ray diffraction, Brunauer-Emmett-Teller method, scanning electron microscopy, high-resolution transmission electron microscopy, and vibrating-sample magnetometer, a kind of copper-modified nanomagnetic material (Cu-nFe₃O₄) was successfully prepared by a one-step synthesis method. Among them, compared with the two-step synthesis method of Cu/Fe₃O₄ and Cu/nFe₃O₄, Cu-nFe₃O₄ has the best effect on chlortetracycline (CTC) removal. The batch study results indicate that the maximum removal of chlortetracycline is 99.0% at a dosage = 2.0 g L^-1, copper loading = 0.8 mM, and C ₀ = 100 mg L^-1 at the optimum conditions within 90 min. The effects of humic acids (HA), NO₃ ^-, Cl^-, CO₃ ^2-, and PO₄ ^3- on the CTC removal by Cu-nFe₃O₄ are also investigated. Repeated experiments were performed on the prepared Cu-nFe₃O₄, indicating that Cu-nFe₃O₄ has good recyclability. The kinetics of the Cu-nFe₃O₄ removal of CTC was investigated, indicating that the reaction conformed to the double constant model and the reaction is mainly dominated by a chemical reaction with physical adsorption. Finally, the mechanism of the CTC removal by Cu-nFe₃O₄ in a heterogeneous environment was clarified. This study aims to provide an experimental basis for the environmental application of Cu-nFe₃O₄.

Effective degradation of phenol via catalytic wet peroxide oxidation over N, S, and Fe-tridoped activated carbon

The N, S, and Fe-tridoped carbon catalysts (NSFe-Cs), Fe/ACNS1 and Fe/ACNS2, were synthesized by wet impregnation with different concentration of ammonium ferrous sulfate solution. The prepared catalysts have a similar textural structure. The N species, S species, Fe^II and Fe^III were simultaneously introduced onto the surface of catalysts. Comparison with the only Fe doped catalyst, NSFe-Cs showed greater stability and higher phenol removal in catalytic wet peroxide oxidation at different reaction condition. The main intermediates including p-hydroxybenzoic acid, formic acid, and maleic acid were determined in the treated wastewater. The high catalytic activity for NSFe-C was related to the ability of H₂O₂ decomposition. NSFe-Cs have more amount of Fe^II partially due to the formation of FeS₂, which promoted the decomposition of H₂O₂ on Fe/ACNS1 and Fe/ACNS2 surface. The generation of ·OH and ·HO₂/·O₂^- radicals in the bulk solution was crucial to phenol degradation, and the decomposition of H₂O₂ complied with the pseudo-first-order kinetics. The highly linear relationship between decomposition kinetic constant for H₂O₂ and the amount of surface groups suggested, including Fe^II species, pyridinic N/Fe-bonded N, pyrrolic N as well as graphitic N were responsible to the high activity of NSFe-Cs.

Synergistic coupling Co3Fe7 alloy and CoFe2O4 spinel for highly efficient removal of 2,4-dichlorophenol by activating peroxymonosulfate

Efficient wastewater restoration depends on the robustness and capability of the catalyst to promote sophisticated decontamination technologies. In this study, Co₃Fe₇-CoFe₂O₄ nanoparticles (NPs) prepared by facile pyrolysis were completely characterized and used to decompose 2,4-dichlorophenol (2,4-DCP). Furthermore, the catalytic performance and relevant mechanisms involved in the activation of peroxymonosulfate (PMS) were also investigated. The optimal conditions were achieved at the catalyst loading of 0.05 g L^-1, PMS dosage of 1.26 g L^-1, and pH of 7.7 through the response surface methodology by using the Box-Behnken design model. Under optimal conditions, 97.1% efficiency of 2,4-DCP removal was obtained within 30 min. Moreover, the quenching experiments and electron paramagnetic resonance result indicated that sulfate (SO₄^•-) and hydroxyl (HO^•) radicals were considered as the dominant reactive oxygen species, which resulted in the effective removal of 2,4-DCP in the Co₃Fe₇-CoFe₂O₄/PMS system. Moreover, Co₃Fe₇-CoFe₂O₄ showed efficient catalytic performance in continuous five runs and exhibited less metal leaching of 0.052 and 0.036 mg L^-1 for Co and Fe species, respectively. Furthermore, no considerable change was observed in the structural characteristics of the fresh and used Co₃Fe₇-CoFe₂O₄ catalytic system. The above-mentioned results indicated that the synergistic effects between Co₃Fe₇ alloy and CoFe₂O₄ spinel not only significantly improved the activity and long-term durability of the catalyst, but also accelerated the Co³⁺/Co²⁺ and Fe³⁺/Fe²⁺ redox cycles. Overall, the Co₃Fe₇-CoFe₂O₄/PMS system provides a novel advanced oxidation approach to further develop multifunctional transition metal-based nanomaterials responsible for producing surface-bound radicals and enhancing the remediation of refractory pollutants in the environmental application.

N-doped carbon coated Mn3O4/PdCu nanocomposite as a high-performance catalyst for 4-nitrophenol reduction

This paper reports the chemical synthesis of highly-active Mn₃O₄/PdCu nanocomposites coated with N-doped carbon (NC) shell using polydopamine (PDA) as the carbon source, which provides high specific surface area and pore volume. The structure and morphology of Mn₃O₄/PdCu@NC nanocomposites were systematically studied. Taking advantage of the synergistic effects of PdCu alloy and Mn₃O₄ support, the Mn₃O₄/PdCu@NC catalyst exhibited an outstanding activity toward the reduction of 4-nitrophenol (4-NP), in comparison to Mn₃O₄/PdM@NC (M = Ni, Au, Ag), Mn₃O₄/PdCu@PDA, and commercial Pd/C catalyst. Owing to the protection by NC shell, the as-prepared catalyst showed stable conversion efficiency of up to 90% over ten successive cycles. Considering 4-NP as one of the important organic pollutants from industrial production, the effects of various inorganic and organic species on the catalytic efficiency were further tested and most of them had negligible impact. This strategy of utilizing an N-doped carbon shell could be extended to obtain PdCu alloys supported on other metal oxides, making it applicable for applications in treatment of environmental pollutants.

Sulfide and arsenic compounds removal from liquid digestate by ferric coagulation and toxicity evaluation

The liquid digestate has been regarded as a potential organic fertilizer for its benefit in nutrients recovery. However, the potential risk of hazardous substances remaining in the wastewater was still one of the main obstacles for the wastewater application in the circular agriculture. The pretreatment is important to remove pollutants with relatively satisfied results. Ferric coagulation was a feasible way to simultaneously remove various contaminants in the wastewater with few residuals of ferric ions under alkaline and neutral conditions. In special, it could reduce the residues of sulfide and arsenic compounds. We gained insights into the mechanism of ferric coagulation in removing sulfide and arsenic compounds. Redox reaction and precipitation were the reasons resulting in removing sulfide. The formation of precipitate by combining with iron(III) contributes to the removal of arsenic compounds. Toxicity tests using Scenedesmus obliquus and Chlorella pyrenoidosa showed an obvious reduction of toxicity for the liquid digestate after ferric coagulation. Besides, ferric coagulation could efficiently remove turbidity, reduce COD, and eliminate dissolved organic matters correlated with the fate of heavy metal and antibiotics. Therefore, this paper could give basic data and technique supports for the secure utilization and pollution control of liquid digestate. PRACTITIONER POINTS: Most sulfide and arsenic compounds were removed by 0.01 M ferric coagulation. Mechanisms on removing hazardous substances by ferric coagulation were discussed based on analysis of X-ray photoelectron spectroscopy and FTIR. The evaluation by two algae showed the toxicity of liquid digestate could be reduced obviously after ferric coagulation.

Enhanced activation of peroxymonosulfte by LaFeO3 perovskite supported on Al2O3 for degradation of organic pollutants

In this study, the effect of various supports on activation of peroxymonosulfate and consequent degradation of Acid Orange 7 (AO7) in aqueous solutions was examined at the presence of LaFeO₃ perovskite as catalyst. Results showed that the AO7 degradation efficiency by LaFeO₃ supported on different supports was in an order of LaFeO₃/Al₂O₃ (86.2%) > LaFeO₃ (70.8%) > LaFeO₃/CeO₂ (59.0%) > LaFeO₃/SiO₂ (52.3%) > LaFeO₃/TiO₂ (32.2%). Moreover, the pseudo first-order rate constant for AO7 degradation by LaFeO₃/Al₂O₃ was 3.2 times than that by LaFeO₃. The enhancement was attributed to its large surface area, abundant chemisorbed surface-active oxygen, redox property and faster electron transfer. AO7 degradation and the leaching of iron ions decreased with the increase of pH. Data of electron spin resonance spectroscopy and quenching experiments revealed that sulfate and hydroxyl radicals were generated on LaFeO₃/Al₂O₃ surface, while sulfate radicals were identified to be the main reactive species responsible for AO7 degradation. Mechanisms for peroxymonosulfate activation were consequently proposed. Furthermore, LaFeO₃/Al₂O₃ catalyst exhibited a superior stability after five cycles. This work provides a new approach for design of iron-based perovskite catalysts with high and stable catalytic activity for removal of organic pollutants from aqueous solutions.

Facile preparation of CoMoO4 nanorods at macroporous carbon hybrid electrocatalyst for non-enzymatic glucose detection

Glucose is a popular biosensor target due to its closely with diabetes or hypoglycemia in blood. Designing efficiency electrocatalysts for the determination of glucose is vital to develop glucose detection devices. CoMoO₄, as a kind of bimetallic oxide material, exhibits unique electrochemical properties. 3D macroporous carbon (MPC) has large specific surface area and excellent electrical conductivity, providing an effective support for loading other nano-entities to form novel composite with good synergetic effects. Herein, nanorod-like CoMoO₄ anchored onto MPC support was synthesized for the development of a promising electrochemical sensing platform for glucose. Attributing to the synergic effects between the good electrocatalytic performance of CoMoO₄ nanorods and the extraordinary electrical conductivity of 3D layered MPC, the novel CoMoO₄/MPC composites non-enzymatic sensor shows excellent electrocatalytic performance for oxidation of glucose. Under the optimum conditions, the proposed CoMoO₄/MPC hybrids provided a reliable linear range of 5 × 10^-7 to 1.08 × 10^-4 M with a low limit of detection (0.13 μM) for the detection of glucose. Meanwhile, the CoMoO₄/MPC sensing platform shows fast response time of 1.76 s, good stability and selectivity for detecting glucose. Moreover, this non-enzymatic sensor also has been successfully applied to measure glucose level in human blood samples. Therefore, the developed sensor holds a new promise for the construction of facile and sensitive non-enzymatic glucose analytical platform.

Electrochemical removal of amoxicillin using a Cu doped PbO2 electrode: Electrode characterization, operational parameters optimization and degradation mechanism

This work investigated the electrochemical degradation of amoxicillin (AMX) in aqueous solution with Cu-PbO2 electrode. The main influence factors on the degradation of AMX, such as Na2SO4 concentration, initial AMX concentration, current density and initial pH value, were analyzed in detail. Under the optimal conditions, the removal rates of AMX and chemical oxygen demand (COD) reached 99.4% and 46.3% after 150 min treatment. The results indicated that the electrochemical degradation of AMX fitted pseudo-first-order reaction kinetics. Compared with undoped PbO2 electrode, Cu-PbO2 electrode had a smaller crystal size, more proportion of hydroxyl oxygen species, greater AMX and chemical oxygen demand (COD) removal efficiency, higher average current efficiency (ACE) and lower electrical efficiency per log order (EE/O). Electrochemical oxidation using Cu-PbO2 electrodes was an effective way to eliminate amoxicillin in aqueous solution. Moreover, a possible degradation pathway including ring open and mineralization was proposed by intermediate products determined by GC-MS method. This paper could provide basic data and technique reference for the amoxicillin wastewater pollution control.

Strengthened Fenton degradation of phenol catalyzed by core/shell Fe-Pd@C nanocomposites derived from mechanochemically synthesized Fe-Metal organic frameworks

We have prepared core/shell structured hollow Fe-Pd@C nanomaterials derived from Fe-metal organic frameworks which were synthesized via cheap, fast and simple mechanochemical technique. The obtained Fe-Pd@C can steadily and continuously release Fe²⁺ from the galvanic corrosion of Fe⁰ anode to trigger H₂O₂ decomposition into hydroxyl radicals and cause fast (10 min) and efficient (mineralization rate 95%) degradation of phenol. The presence of low level of Pd NPs in Fe-Pd@C (mass ratio of the raw material: Fe/Pd = 100:1) facilitated fast Fe³⁺/Fe²⁺ redox cycle and thus improved the catalytic performance and pH endurance of the Fe-Pd@C. After recycled four times, Fe-Pd@C remained high catalytic performance and released low level of iron ions (2.5 mg L^-1), which reduced the production of iron sludge after usage. In contrast to zero-valent iron (ZVI) and commercial physically mixed Fe/C materials, the core/shell structure of Fe-Pd@C ensured efficient electron transferring from Fe⁰ to carbon cathode and targets, and prevented the precipitation of iron ions on Fe⁰ surface, avoiding the deactivation of Fe⁰ and termination of Fe-C internal micro-electrolysis (IME) and extending their service life. The reactive species quenching experiments and ESR characterization proved the synergistic effect of electrons and hydroxyl free radicals on degradation of phenol. The carbon-centered DMPO radical detected in reaction solution can be regarded as a proof for the strengthened oxidation ability of the combined IME and Fenton reaction.

Defect-Abundant Covalent Triazine Frameworks as Sunlight-Driven Self-Cleaning Adsorbents for Volatile Aromatic Pollutants in Water

Covalent triazine frameworks (CTFs) with high adsorption potential and photocatalytic ability features are expected to be designed as a new class of adsorbents that can regenerate themselves just by harnessing sunlight. To simultaneously improve both the adsorption and photocatalytic regeneration performance, a defect-abundant CTF-m was designed and tuned effectively by varying the lengths of benzene ring chains incorporated into the CTF backbone. It has been demonstrated that two kinds of defects in terms of broken benzene rings and pyrrole nitrogen were newly generated, other than the normal benzene rings and triazine units in the CTF-m skeleton. Benefiting from these defects, the adsorption sites with high energy for adsorbing volatile aromatic pollutants were significantly increased, which are reflected by higher saturated adsorption capacities of CTF-m (3.026 mmol/g for benzene (BEN), 1.490 mmol/g for naphthalene (NAP), and 0.863 mmol/g for phenol (PHE)) compared with those of CTF-1 and CTF-2. Furthermore, these defects narrowed the band structure and facilitated the separation of photogenerated charge carries, thus promoting photocatalytic regeneration. The percentage of CTF-m regenerated was still higher than 90% in the fourth cycle. These experimental results, together with the density functional theory (DFT) studies, soundly corroborated that the defects could optimize the adsorption and regeneration property of CTF-m. The present work highlights the potential of fabrication of defective CTFs as solar-driven self-cleaning adsorbents to remove pollutants from water.

Enhanced catalytic ozonation by highly dispersed CeO2 on carbon nanotubes for mineralization of organic pollutants

Heterogeneous catalytic ozonation, in which ozone is activated by various catalysts to produce reactive oxygen species (ROS), is an effective approach to degrade persistent organic pollutants in water. However, catalyst with high activity and good stability for catalytic ozonation still remains rare. In this work, a highly dispersed cerium oxide on oxidized carbon nanotubes (CeO₂-OCNT) were prepared and characterized by X-ray diffractometer (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and temperature-programmed reduction using hydrogen (TPR-H₂) experiments. The as-synthesized CeO₂-OCNT showed significantly enhanced catalytic performance for degrading organic pollutants during catalytic ozonation. The removal efficiency of optimized CeO₂-OCNT for phenol mineralization was 2-3 times of pure CeO₂ and OCNT, and was also better than that of a composite with the same composition, which demonstrated a synergic effect between OCNT and CeO₂ on CeO₂-OCNT for catalytic ozonation. The TOC removal efficiency exhibited no obvious reduction after five cycling experiments, indicating the synthesized CeO₂-OCNT possessed good reusability. Moreover, electron paramagnetic resonance (EPR) and radicals quenching experiments revealed that hydroxyl radicals (OH) were the dominant ROS for organic pollutants degradation. The superior activity of CeO₂-OCNT for catalytic ozonation could be attributed to the well-dispersed CeO₂, the improved mass transfer, and the facilitated redox Ce³⁺/Ce⁴⁺ cycling.

Iron-doped ordered mesoporous Co3O4 activation of peroxymonosulfate for ciprofloxacin degradation: Performance, mechanism and degradation pathway

Ordered mesoporous Co₃O₄ (OM-Co₃O₄) displayed superior performance for peroxymonosulfate (PMS) activation. While, the separation and recovery of the catalyst after catalytic oxidation needed tedious operation. In this study, the as-synthesized iron-doped OM-Co₃O₄ not only inherited the merits of ordered mesoporous materials such as high surface area and abundant mesoporous structure, but endowed them with ferromagnetism, facilitating their separation from the solution. Compared with spinel Co₃O₄, iron-doped OM-Co₃O₄ showed superior catalytic activity, wide application scope, excellent reusability and long-term stability, fully validated that iron-doped OM-Co₃O₄ can be a promising heterogeneous PMS activator for environmental application. High catalyst loading and PMS concentration were both beneficial to CIP degradation. The best CIP degradation occurred under base conditions. Chlorine and bicarbonate presented completely opposite two-side effects. The mechanism of CIP degradation was primarily attributed to SO₄^- and OH to a lesser extent. The rapid redox cycles of M²⁺/M³⁺ (M = Co, Fe) and O^2-/O₂ ensured the continuous generation of reactive oxygen species and the efficient degradation of CIP. The cleavage of piperazine ring, hydroxylation and defluorination were identified as the main oxidation pathways for CIP degradation in iron-doped OM-Co₃O₄ activated PMS system.