Investigation into lanthanum-coated biochar obtained from urban dewatered sewage sludge for enhanced phosphate adsorption

Recycling and reuse of waste agricultural plastics with hydrothermal pretreatment and low-temperature pyrolysis method

Recycling and reuse of agricultural plastics is an urgent worldwide issue. In this work, it is shown that low-density polyethylene (PE) typically used in mulch films can be converted into high-capacity P and N adsorbents through a two-step method that uses hydrothermal pretreatment (180 °C, 24 h) followed by pyrolysis at 500 °C with Ca(OH)2 additive. CaPE@HC500 materials prepared with the proposed two-step method were found to have high adsorption capacities for phosphate (263.6 mg/g) and nitrogen (200.7 mg/g) over wide ranges of pH (3-11). Dynamic adsorption of phosphate by CaPE@HC500 material in a packed-bed had a half-time breakthrough of 210 min indicating the feasibility of continuous systems. Material stability, cost, environmental-friendliness, and recyclability of the CaPE@HC500 material were determined to be superior to literature-proposed Ca-containing adsorbents. The two-step method for converting waste agricultural plastic mulch films into adsorbents is robust and highly-applicable to industrial settings.

Towards zero-waste processes: Waste wool derivatives as phosphate adsorbents and auxiliaries for textiles' natural dyeing

The textile industry is a pillar of the manufacturing sector worldwide, but it still represents a significantly polluting production sector since it is energy-, water- and natural resource-intensive. Herein, waste wool that did not meet the technical requirements to be used for yarns and fabrics was recovered first to prepare materials for wastewater remediation, specifically for phosphate removal. The wool underwent an alkaline treatment, eventually saturated with FeCl3 and then left at room temperature or thermally treated to induce crosslinking/stabilisation, obtaining adsorbent panels. The main characterisation findings concerned the impact of alkaline treatment on morphology and structure; additionally, the samples with iron displayed a behaviour attributable to a crosslinking effect operated by Fe3+. Batch experiments showed that only samples with iron were efficient in phosphate adsorption, with a high removal percentage obtained in a wide pH range. Adsorption isotherms and kinetics were investigated, suggesting a complex system of interactions. Moreover, during the alkaline treatment necessary to prepare such wool-derived adsorbent panels, a significant amount of wool hydrolysates left in the solution was produced. These substances, in view of zero-waste procedures, were isolated and re-employed as dyeing auxiliaries. Preliminary results demonstrated that the wool hydrolysates enabled the dyeing of cotton with natural dyes, which is generally a tricky process.

Machine learning-driven prediction of phosphorus removal performance of metal-modified biochar and optimization of preparation processes considering water quality management objectives

Developing an optimized and targeted design approach for metal-modified biochar based on water quality conditions and management is achievable through machine learning. This study leveraged machine learning to analyze experimental data on phosphate adsorption by metal-modified biochar from literature published in Web of Science. Using six machine learning models, the phosphate adsorption capacity of biochar and residual phosphate concentration were predicted. After hyperparameter optimization, the gradient boosting model exhibited superior training performance (R2 > 0.96). Metal load quantity, solid-liquid ratio, and pH were key factors influencing adsorption performance. Optimal preparation parameters indicated that Mg-modified biochar achieved the highest adsorption capacity (387-396 mg/g), while La-modified biochar displayed the lowest residual phosphate concentration (0 mg/L). The results of verification experiments based on optimized process parameters closely aligned with model predictions. This study introduces a new machine learning-based approach for tailoring biochar preparation processes considering different water quality management objectives.

Waste derived modified biochar as promising functional material for enhanced water remediation potential

The waste management and water purification are daunting environmental challenges. Biochar, a carbonaceous material prepared from diverse organic waste (agricultural, household residues and municipal sewage sludge) has garnered substantial attention due to its excellent attributes, including carbon content, cation exchange efficacy, ample specific surface area, and structural robustness. Thus, the present review comprehensively analyzes bio waste-derived biochar with a particular emphasis on water remediation applications. This article primarily delves into various strategies for modifying biochar, elucidating the underlying mechanisms behind these modifications and their potential for bolstering pollutant removal efficiency. Furthermore, it addresses the impact of functionalization on both biochar stability and cost for commercialization. Lastly, the article outlines key developments, SWOT analysis, and future prospects, offering insights into the practical execution of biochar applications at a larger scale. Therefore, this article paves the way for future research to deepen the understanding of modified biochar with mechanisms for exploring water remediation applications in a more sustainable manner.

Green synthesis of CaxLa1-xMnO3 with modulation of mesoporous and vacancies for efficient low concentration phosphate adsorption

Phosphate concentrations in eutrophic surface waters are usually low, and efficient removal of low concentration phosphate remains a challenge. In this study, Ca-doped LaMnO3 synthesized at doping ratios, designated as CaxLa1-xMnO3 (x = 0, 0.2, 0.4, 0.7), were compared. It was found that, the adsorption capacity of Ca0.4La0.6MnO3 material reached 63.01 mg/g at pH = 5, increased by 63.6% over the undoped LaMnO3 perovskite. For long-term adsorption, Ca0.4La0.6MnO3 could constantly adsorb phosphate to avoid phosphate accumulation (<0.05 mg/L). This proves that Ca0.4La0.6MnO3 has the ability to control dynamic water eutrophication. Characterization and density functional theory results confirmed that CaxLa1-xMnO3 can increase the content of mesopores and oxygen vacancies, providing additional active sites. This reduces the adsorption energy of the La site, promotes electron transfer, and increases its affinity. It provides a new method for removing low-concentration phosphates.

Construction of 3D network aluminum sludge-based hydrogel beads: combination of macroization, amino functionalization, and resource utilization

An aluminum sludge-based composite material was constructed against the problems of phosphorus pollution and the waste of aluminum sludge resources. Utilizing metal Ce doping and hydrogel microbeads with pore preparation, the adsorption performance of the original sludge was improved. Meanwhile, the macroscopic body was constructed, and on this basis, polyethyleneimine (PEI) was introduced to complete the amino functionalization further to enhance the adsorption of phosphorus by the adsorbent, and NH-CeAIS-10 microbeads were successfully prepared. In adsorption, microbeads with larger specific surface area and richer functional groups are better choice compared to original sludge. The results of SEM, BET, FT-IR, and XPS analyses indicate that the adsorption of phosphorus by the microbeads is mainly achieved through electrostatic interactions, ligand exchange, and the formation of inner-sphere complexes. According to the Langmuir model, the maximum phosphorus adsorption capacity of NH-CeAIS-10 was 29.56 mg g-1, which was four times higher compared to native aluminum sludge. This also confirms the significant enhancement of phosphorus adsorption through the modification of aluminum sludge. Besides, in dynamic adsorption column experiments, the material exhibited up to 99% removal in simulated wastewater for up to 30 days, demonstrating the great adsorption potential of NH-CeAIS-10 in engineering applications.

Aluminium dross waste utilization for phosphate removal and recovery from aqueous environment: Operational feasibility development

The need to minimize eutrophication in water bodies and the shortage of phosphate rock reserves has stimulated the search for sequestration and recovery of phosphate from alternative sources, including wastewater. In this study, aluminium dross (AD), a smelting industry waste/by-product, was converted to high-value material by encapsulation in calcium alginate (Ca-Alg) beads, viz. Ca-Alg-AD and utilized for adsorptive/uptake removal and phosphate recovery from an aqueous environment. Encapsulation of AD in alginate beads solves serious operational difficulties of using raw AD material directly due to density difference constraining efficient contact of AD with pollutants present in water and post-treatment recovery of AD material. The phosphate removal was evaluated in both batch and continuous flow operation modes. The batch adsorption study revealed 96.86% phosphate removal from 10 mg L-1 of initial phosphate concentration in 70 min of optimal contact time. Further, the phosphate removal potential of Ca-Alg-AD beads turned out to be independent of solution pH, with an average of 95.93 ± 1.40 % phosphate removal in the 2-9 pH range. The result reflects phosphate adsorption on Ca-Alg-AD beads following a second-order pseudo-kinetic model. Ca-Alg-AD beads-based adsorption followed Freundlich and Langmuir isotherm models. Further, a continuous packed bed column study revealed a total phosphate adsorption capacity of 1.089 mg g-1. The chemical composition, physical stability, and surface properties of Ca-Alg-AD beads were analyzed by means of state-of-the-art analytical techniques, such as Scanning Electron Microscopy-Energy Dispersive X-ray spectroscopy (SEM-EDX), Fourier Transform Infrared Spectroscopy (FTIR) and thermogravimetry/Differential Thermal Analysis (TG/DTA). These characterization techniques comprehend the mechanism and influence of surface properties and morphology on the phosphate adsorption behaviour, which induce the involvement of multiple mechanisms such as ligand complexation, ion exchange, and electrostatic attraction for phosphate adsorption on Ca-Alg-AD beads.

Adsorption recovery of phosphorus in contaminated water by calcium modified biochar derived from spent coffee grounds

Phosphate recovery from water is essential for reducing water eutrophication and alleviating the phosphorus resource crisis. In this study, spent coffee grounds and CaCl2 were used as raw materials and a modifier, respectively, to create a novel calcium modified biochar (MBC) for removing phosphorus from water. The modified biochar (MBC) was the best at removing phosphorous when the modifier concentration was 1.5 M with theoretically maximum adsorption capacity of 70.26 mg/g. MBC also performed well in the wide pH range of 3-11 under different phosphorus concentration gradients, with phosphorus removal efficiency of more than 50 %. According to kinetic analysis, the adsorption process at low phosphorus concentrations (50-100 mg/L) can be more properly described by the pseudo-first-order model, while the pseudo-second-order model best describes the adsorption process at high concentrations (200-600 mg/L). The thermodynamic analysis indicated that the adsorption process was spontaneous and endothermic. Characterization results revealed that surface precipitation, complexation, and ligand exchange were the dominant mechanisms of phosphorus adsorption. MBC has great potential to recover phosphorus from wastewater.

Effect of Modified Biochar Prepared by Co-pyrolysis of MgO on Phosphate Adsorption Performance and Seed Germination

Biochar is currently used as a phosphate adsorbent in water and subsequently as a soil amendment. In this study, modified biochar was prepared directly by co-pyrolysis of MgO and rice straw, and a preliminary ecotoxicological assessment was performed before the application of modified biochar to soil. The effects of single factors, such as pyrolysis temperature, dosage, pH, and coexisting ions, on phosphate adsorption performance were investigated. In addition, after phosphate adsorption, the effects of modified biochar leachate on the germination of corn and rice seeds were examined. The results showed that phosphate adsorption by the modified biochar first increased and then decreased as the pyrolysis temperature increased, with modified biochar prepared at 800 °C showing the greatest adsorption. In addition, a comprehensive cost analysis showed that the best phosphate adsorption effect of modified biochar was achieved at a dosage of 0.10 g and a solution pH of 3. In contrast, the presence of competitive coexisting ions, Cl- , NO3 - , CO3 2- , and SO4 2- , reduced the phosphate adsorption capacity of the modified biochar. The adsorption kinetics results revealed that the process of phosphate adsorption by the modified biochar was more in line with the pseudo-second-order model and dominated by chemisorption. Moreover, the adsorption isotherm results indicated that the process was more in line with the Langmuir model and dominated by monomolecular layer adsorption, with a maximum adsorption of 217.54 mg/g. Subsequent seed germination tests showed that phosphate-adsorbed modified biochar leachate had no significant effect on the germination rate of corn seeds, whereas it improved the germination rate of rice seeds. Together, these results provide guidance for the application of modified biochar firstly as an adsorbent of phosphate and subsequently as a soil remediator.

Adsorption-electrochemical mediated precipitation for phosphorus recovery from sludge filter wastewater with a lanthanum-modified cellulose sponge filter

In this study, the sludge filter wastewater is confirmed to investigate the effects of adsorption-electrochemical mediated precipitation (EMP) driven phosphorus recovery on the basis of lanthanum-modified cellulose sponge filter (LCLM) material. The adsorption-EMP method relies on in situ recovery phosphate (P) from the used desorption agent (NaOH-NaCl binary solution) via the formation of Ca5(PO4)3OH all while preserving the alkalinity of the desorption agents which benefited long-term application. The lanthanum content of LCLM was 9.0 mg/g, and the adsorption capacity reached 226.1 ± 15.2 mg P/g La at an equilibrium concentration of 3.9 mg P/L. After adsorption, 55.7 % of P was recovered, and the corresponding alkalinity increased from 1.9 mmol/L to 2.2 mmol/L. Adsorption mechanism analysis revealed that the high lanthanum usage of LCLM was attributed to the synergistic effect of the lattice oxygen of LaO and LaPO4·0.5H2O crystallite formation. Additionally, the Ca5(PO4)3OH was found precipitated in the precipitation in the cathode chamber (P-CC) rather than on the surface/section of cation exchange membrane (CEM) and cathode indicating that the P recovery process was controlled by the saturation of CaP species in the EMP system and the electromigration effect. These findings present a new strategy to promote the effective utilization of rare earth elements for P adsorption and demonstrate the potential application of adsorption-EMP systems in dephosphorization for wastewater treatment.

Studies on ultrafast and remarkable removal of phosphate from sewage water by metal-organic frameworks

In the proposed research, a lanthanum-doped metal-organic framework (La-ATP) has been synthesised to remove phosphate from contaminated aqueous solutions. La-ATP was synthesised by a green energy-saving route using microwave irradiation and exhibited a phenomenal sorption capacity of 290 mg/g for the removal of phosphate. At a minimal dose of 0.1 g/L, 25 mg/L of phosphate gets reduced to 6.3 mg/L within 5 min and reaches equilibrium in 25 min. The isoelectric point of La-ATP was found to be 8.99, and it is efficient in removing phosphate over a wide range of pH 5-10. The existence of commonly occurring competing anions like sulphate, fluoride, chloride, arsenate, bicarbonate, and nitrate does not affect the uptake capacity of La-ATP towards phosphate ions. Furthermore, the robustness of La-ATP is demonstrated by its applicability to remove phosphate from real-life sewage water by reducing 10 mg/L of phosphorus from sewage water to < 0.02 mg/L. The primary mechanism governing phosphate removal was found to be ionic interaction and ligand exchange. Therefore, La-ATP can be considered a viable candidate for the treatment of eutrophic water streams because of its high sorption capacity, super-fast kinetics, and adaptability to contaminated sewage.

Magnetic biochar with Mg/La modification for highly effective phosphate adsorption and its potential application as an algaecide and fertilizer

In this study, a highly efficient phosphate adsorbent (MBC/Mg-La) based on magnetic biochar was successfully synthesized through Mg-La modification. The phosphate adsorption capacity of biochar was significantly enhanced after Mg-La modification. The adsorbent exhibited an excellent phosphate adsorption performance, particularly for treating low-concentration phosphate wastewater. Within a wide pH range, the adsorbent maintained a stable phosphate adsorption capacity. Furthermore, it showed a high adsorption selectivity for phosphate. Therefore, given the excellent phosphate adsorption performance, the adsorbent could effectively inhibit algae growth by removing phosphate from water. Furthermore, the adsorbent after phosphate adsorption can be easily recycled through magnetic separation, which can serve as a phosphorus fertilizer to promote the growth of Lolium perenne L.

Significant Improvement of Adsorption for Phosphate Removal by Lanthanum-Loaded Biochar

Due to eutrophication, removing phosphate ions from wastewater has received a lot of attention. In order to improve the phosphorus adsorption capacity of the material, this study used biomass pyrolysis to create a series of biochars modified with metal chloride ions. In accordance with adsorption tests, lanthanum-loaded biochar (LCBC) had a significant phosphorus adsorption capacity of approximately 666.67 mg/g, which was 30 times greater than that of pristine biochar. Adsorption kinetic analysis revealed that the LCBC's adsorption process could be fitted to the pseudo-secondary kinetic equation, indicating that chemical processes were primarily responsible for controlling the adsorption process. Zeta potential, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy analysis showed that the main adsorption mechanism of LCBC for phosphate removal was electrostatic attraction of protonated H+ with negatively charged mono-hydrogen phosphate and dihydrogen phosphate ions and complexation reaction of the C=O on the carboxyl group and P=O on the phosphate group with the oxygen on the phosphate group and hydroxyl group. According to regeneration performance results, LCBC performed relatively better than as-prepared adsorbents, and the phosphate removal rate was approximately 75.1% after the fifth regeneration cycle. The study provided a potential approach for creating and preparing an adsorbent with high adsorption for phosphate removal.

A critical review on the development of lanthanum-engineered biochar for environmental applications

Biochar and lanthanum (La) have been widely used in environment. However, there is a lack of knowledge and perspective on the development of La-engineered biochar (LEB) for environmental applications. This review shows that LEBs with a variety of La species via pre-/post-doping routes are developed for environmental applications. Specifically, precipitation, gelation, and calcination are the common sub-processes involved in the pre-/post-doping of La on the resultant LEB. The dominant La species for LEBs is La(OH)₃, which is formed through precipitation of La ions with various bases. Various La carbonates, e.g., LaOHCO₃, La₂(CO₃)₃, La₂CO₅, and NaLa(CO₃)₂, are also involved in the preparation of LEBs. The LEBs are high-efficient in the adsorption of phosphate, arsenic, antimonate and fluoride ions, attributed to the strong affinity of La to oxyanions and Lewis hard base. Lanthanum is also favorable for co-doping with transition metal species to further enhance the performances in adsorption or catalysis. This review also analyzes the prospects and future challenges for the preparation and application of LEBs in environment. Finally, this review is beneficial to inspire new breakthroughs on the preparation and environmental application of LEBs.

Adsorption mechanism of phosphorus on biomass ash modified with lanthanum immobilized by chitosan

The immobilized lanthanum-modified biomass ash gel ball (CS-La-BA) was prepared with lanthanum chloride, biomass ash, and chitosan to remove phosphorus from water. CS-La-BA was characterized by several analytical techniques. SEM-EDS results showed that CS-La-BA has a well-developed pore structure and abundant adsorption sites. The surface area of BET is 75.46 m²/g and the pore size is mostly at 1.84 nm, indicating that it is a composite porous material with abundant microporous structure. The presence of La on biomass ash and the charge property of CS-La-BA were determined by XRD and zeta potential, and the adsorption mechanism of CS-La-BA on phosphate, including precipitation, electrostatic adsorption, ligand exchange, and complexation mechanism, was revealed by FTIR and XPS. The effects of pH, temperature, adsorbent dosage, initial phosphorus concentration, adsorption time, and coexisting ions on the phosphorus uptake performance of CS-La-BA were discussed. The adsorption experiment results show that the phosphorus removal rate of CS-La-BA can reach 95.6%. Even after six desorption and regeneration experiments, the phosphorus removal rate still reaches 68.13%, which indicates that CS-La-BA has good phosphorus adsorption performance and desorption and regeneration capacity. The phosphorus adsorption process of CS-La-BA conforms to the Freundlich isotherm adsorption equation and general-order kinetic model. The internal diffusion of the adsorption process is dominant, and the maximum adsorption capacity is 31.73 mg/g (25 ℃). Thermodynamic experiments show that the adsorption process of phosphorus by CS-La-BA is a spontaneous entropy increase process.

Achieving win-win outcomes with cerium-loaded porous aluminum sludge hydrogel microspheres for enhanced phosphate removal

Breaking the technical bottleneck of traditional powdered adsorbent in phosphate adsorption application treatment, a macroscopic high adsorption performance aluminum sludge-based composite hydrogel material was constructed to synergistically solve the problems of water eutrophication and aluminum sludge resourcization. In this study, porous Ce-modified aluminum sludge hydrogel microspheres (Ce-AlS-SA) were prepared to improve the surface chemical structure and microscopic morphology of the macroscopic adsorbent material to enhance the adsorption capacity and achieve effective solid-liquid separation. The best adsorption performance of the material (Ce-AlS₁₂-SA₁) was obtained when the Ce-AlS: SA: Na₂CO₃ was 12:1:1, and obtained the optimal adsorption conditions by Response Surface Method (RSM) with 1.5 mg/L of the dosage, 4 of pH and 50 mg/L of C_phosphate. The maximum adsorption of 20.36 mg P/g was obtained by the Langmuir model at 303 K, which was 2.92 times more than raw sludge. According to the Freundlich and pseudo-second-order kinetic model, the adsorption process is chemisorption; the multi-stage adsorption process is reflected in the intraparticle diffusion and film diffusion models. The main mechanisms combined with the characterization analysis are electrostatic gravity, ligand exchange, and inner-sphere complexation. Meanwhile, Ce-AlS₁₂-SA₁ shows good resistance to interference in the coexistence of multiple ions. Therefore, this material can be recognized as a new material with in-depth, diversified and practical needs for resourceful utilization, which is expected to achieve extensive engineering applications in the future.

The Study of Optimal Adsorption Conditions of Phosphate on Fe-Modified Biochar by Response Surface Methodology

A batch of Fe-modified biochars MS (for soybean straw), MR (for rape straw), and MP (for peanut shell) were prepared by impregnating biochars pyrolyzed from three different raw biomass materials, i.e., peanut shell, soybean straw, and rape straw, with FeCl₃ solution in different Fe/C impregnation ratios (0, 0.112, 0.224, 0.448, 0.560, 0.672, and 0.896) in this research. Their characteristics (pH, porosities, surface morphologies, crystal structures, and interfacial chemical behaviors) and phosphate adsorption capacities and mechanisms were evaluated. The optimization of their phosphate removal efficiency (Y%) was analyzed using the response surface method. Our results indicated that MR, MP, and MS showed their best phosphate adsorption capacity at Fe/C ratios of 0.672, 0.672, and 0.560, respectively. Rapid phosphate removal was observed within the first few minutes and the equilibrium was attained by 12 h in all treatment. The optimal conditions for phosphorus removal were pH = 7.0, initial phosphate concentration = 132.64 mg L^-1, and ambient temperature = 25 °C, where the Y% values were 97.76, 90.23, and 86.23% of MS, MP, and MR, respectively. Among the three biochars, the maximum phosphate removal efficiency determined was 97.80%. The phosphate adsorption process of three modified biochars followed a pseudo-second-order adsorption kinetic model, indicating monolayer adsorption based on electrostatic adsorption or ion exchange. Thus, this study clarified the mechanism of phosphate adsorption by three Fe-modified biochar composites, which present as low-cost soil conditioners for rapid and sustainable phosphate removal.

Fe12LaO19 fabricated biochar for removal of phosphorus in water and exploration of its adsorption mechanism

Phosphorus (P) runoff from untreated wastewater and agricultural runoff has become an issue of concern because excessive P is detrimental to the health of water bodies and aquatic organisms such as fishes. Hence, different methods are being developed to salvage this challenge. However, most of the methods are expensive, while some are unsustainable. In this study, a simple method was employed in fabricating an absorbent through the co-precipitation of iron and lanthanum on the matrix of biochar prepared from the spent coffee ground for P uptake. The adsorbent named Fe₁₂LaO₁₉@BC was able to attain equilibrium fast within 60 min when used to adsorb P with 98% P removal within the first 30 min Fe₁₂LaO₁₉@BC also maintained high P adsorption across a pH range of 3-7. In the presence of other anions (SO₄^2-, CO₃^2-, NO₃^-, Cl^-, HCO₃^-) in the solution, Fe₁₂LaO₁₉@BC enabled 71.5-97.8% uptake of P. 81.58 mg P/g maximum adsorption capacity at was reached at 40 °C. The reusability test reveals that about 60% of P uptake was maintained after five adsorption cycles with almost an undisturbed desorption efficiency. The negative value of ΔG°, as shown by the thermodynamic analysis, indicates a favorable and spontaneous reaction during P removal by Fe₁₂LaO₁₉@BC. The XRD analysis showed a major peak corresponding to Fe₁₂LaO_19, which is believed to have facilitated the adsorption of P. The adsorption was controlled by multiple mechanisms. An overview of the study indicates Fe₁₂LaO₁₉@BC as a promising adsorbent for the removal of P in the water.

Effect of CeO2-Reinforcement on Pb Absorption by Coconut Coir-Derived Magnetic Biochar

Magnetic separable biochar holds great promise for the treatment of Pb²⁺-contaminated wastewater. However, the absorption effect of unmodified magnetic biochar is poor. Considering this gap in knowledge, CeO₂-doped magnetic coconut coir biochar (Ce-MCB) and magnetic coconut coir biochar (MCB) for Pb²⁺ absorption were prepared by the impregnation method, and the efficiency of Ce-MCB for Pb²⁺ absorption was evaluated in comparison with MCB. Conducting the absorption experiments, the study provided theoretical support for the exploration of the absorption mechanism. The quantitative analysis exposed that the enhanced absorption capacity of Ce-MCB was attributed to the increase in oxygen-containing functional groups and mineral precipitation. The Langmuir and Freundlich isotherm model showed that Ce-MCB is a suitable adsorbent for Pb²⁺. The absorption characteristics of Ce-MCB was fit well with the pseudo-second-order (PSO) and Langmuir models, which revealed that the absorption of Pb²⁺ in water was monolayer chemisorption with a maximum theoretical adsorption capacity of 140.83 mg·g^-1. The adsorption capacity of Ce-MCB for Pb(II) was sustained above 70% after four cycles. In addition, the saturation magnetization intensity of Ce-MCB was 7.15 emu·g^-1, which was sufficient to separate out from the solution. Overall, Ce-MCB has wide application prospects in terms of biomass resources recycling and environmental conservation.

Synthesis of layered double hydroxide-based hybrid electrode for efficient removal of phosphate ions in capacitive deionization

The removal of phosphate ions by capacitive deionization has become one of the most frontier research topics in the water treatment field in recent years. In this work, hybrid electrodes composed of nickel-iron layered double hydroxide (NiFe-LDH) - anchored on activated carbon fiber (ACF)-were synthesized by a hydrothermal method and subsequently applied in capacitive deionization to remove phosphate ions. The adsorption performance of the two hybrid electrodes on phosphate ions was compared by capacitive deionization experiments. The experiment was carried out for 3 hours to reach equilibrium, and the optimum adsorption of 33.48 mg/g was obtained using NiFe-LDH/ACF-2 hybrid electrode at room temperature (25 °C) and pH = 6.0. The results showed that increasing the loading capacity of NiFe-LDH on ACF might enhance the adsorption capacity of phosphate ions. Furthermore, the calculation of adsorption kinetics and adsorption isotherms elucidated that the adsorption capacity increased with the increasing of applied voltage. Meanwhile, the experimental data were fitted well with pseudo-first-order kinetics and Langmuir isotherms. Notably, it was observed that the pH first increased, then decreased during the adsorption due to the electrolysis of water, while the form of phosphate ions was transformed, with low pH favoring the adsorption of phosphate ions.

Degradation of chlortetracycline hydrochloride by peroxymonosulfate activation on natural manganese sand through response surface methodology

This work studies the degradation of chlortetracycline hydrochloride (CTC) by activated peroxymonosulfate (PMS) with natural manganese sand (NMS). Meanwhile, the NMS was characterized and analyzed by isothermal nitrogen adsorption (BET), energy-dispersive X-ray spectroscopy (EDS) and scanning electron microscope (SEM). It can be induced that NMS material may contain C, O, Al, Si, Fe, Mn, and K, and the proportion of each is 6%, 9%, 13%, 34%, 27%, 5%, and 6%. Critical parameters, including initial pH value, catalyst dosage, and PMS amount, were optimized through response surface methodology. One of the essential significances of response surface methodology (RSM) is the establishment and optimization of the mathematical model to reduce the complexity of the experimental process. It can provide the degree of mutual influence between various factors and optimize the response based on the investigated factors. Results indicated that 81.65% of CTC could be degraded under the optimized conditions of PMS amount 2.02 g/L, the NMS dosage 0.29 g/L and pH 3.87. Also, it shows that NMS is the most powerful of each factor on the degradation efficiency. We proposed the degradation pathways of CTC from the liquid chromatograph-mass spectrometer (LC-MS) results. Therefore, NMS could be applied as an efficient activator of peroxymonosulfate to purify the water and wastewater.

Design and optimization of an innovative lanthanum/chitosan bead for efficient phosphate removal and study of process performance and mechanisms

Presence of excessive phosphorus in surface waters is the main cause for eutrophication. In this study, a lanthanum/chitosan (La/CS) bead was prepared so as to provide a cost-effective solution to the problem. The optimization of bead for the treatment was conducted, leading to the optimal condition: 30 wt% La/CS bead at a dosage of 30 g L^-1 (wet weight). A higher phosphate removal around 90% was obtained in pH 4.0-10.0. Most of uptake occurred in the first 2 h and the equilibrium was reached in about 6 h. Coexisting ions of Cl^-, [Formula: see text] , [Formula: see text] , and [Formula: see text] had negligible effects on the treatment, while the presence of F^- reduced the uptake by 10.39%. The maximum adsorption capacity of 261.1 mg-PO₄·g^-1 (dried weight) at pH 5.0 was achieved, which is much better than many reported La-based adsorbents. The adsorbed phosphate can be effectively recovered with an alkaline solution. A multi-cycle regeneration-reuse study illustrated that the treated water still met the phosphorus discharge standard. The characterization results demonstrated the disappearance of La(OH)₃ and La₂(CO₃)₃ on the bead and the formation of NH₃⁺ … P and La-P groups after the adsorption, indicating the significant roles of ion exchange and electrostatic attraction on the uptake. The excellent performance found in this study clearly indicates that the optimized La/CS bead is promising in the treatment of phosphate and perhaps its recovery for industrial use.

Phosphate adsorption improvement using a novel adsorbent by CaFe/LDH supported onto CO2 activated biochar

It is imperative to remove phosphate from the aquatic system. This nutrient in excess can cause environmental problems such as eutrophication. Therefore, aiming to enhance phosphate removal, this work presents a novel adsorbent developed from the construction of Ca²⁺/Fe³⁺ layer double hydroxides (CaFe/LDH) supported onto biochar physically activated with CO₂ [CaFe/biochar (CO₂)]. Pristine biochar was produced from the pyrolysis of Eucalyptus saligna sawdust, activated with CO₂, and then impregnated with CaFe/LDH. The CaFe/biochar (CO₂) was characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), and Brunauer-Emmett-Teller (BET). The characterization confirmed a proper synthesis of the new adsorbent. Experiments were conducted in the form of batch adsorption. Results indicated that the optimum pH and adsorbent dosage were 2.15 and 0.92 g L^-1, respectively. Adsorption kinetics, isotherms, and thermodynamics were also evaluated. Adsorption kinetics and isotherms were better fitted by the pseudo n order and Freundlich models, respectively. Results also indicated a better adsorption capacity (99.55 mg·g^-1) at 55 °C. The thermodynamic indicators depicted that the adsorption process was favorable, spontaneous, and endothermic. Overall, CaFe/biochar (CO₂) could be potentially applied for the adsorptive removal of phosphate from an aqueous solution.

Phosphate removal and recovery by lanthanum-based adsorbents: A review for current advances

Controlling eutrophication and recovering phosphate from water bodies are hot issues in the 21st century. Adsorption is considered to be the best method for phosphate removal because of its high adsorption efficiency and fast removal rate. Among the many adsorbents, lanthanum (La)-based adsorbents have been paid more and more attention due to their strong affinity to phosphorus. This paper reviews research of phosphate adsorption on La-based adsorbents in different La forms, including lanthanum oxide/hydroxide, lanthanum mixed metal oxide/hydroxide, lanthanum carbonate, La³⁺, La-based metal-organic framework (La-MOF) and La-MOF derivatives. The La-based adsorbents can be loaded on many carriers, such as carbon material, clay minerals, porous silica, polymers, industrial wastes, and others. We find that lanthanum oxide/hydroxide and La³⁺ adsorbents are mostly studied, while those in the forms of lanthanum carbonate, La-MOF, and La-MOF derivatives are relatively few. The kinetic process of most phosphate adsorption is pseudo-second-order and the isotherm process is in accordance with the Langmuir model. The cost of La-based and other traditional adsorbents was compared. The adsorption mechanisms are categorized as electrostatic attraction, ligand exchange, Lewis acid-base interaction, ion exchange and surface precipitation. Besides, regeneration methods of La-based adsorbents are mainly acid, alkali, and salt-alkali. In addition, the La-based adsorbents after absorbing phosphate can be directly used as a slow-release fertilizer. This review provides a basis for the research on phosphate adsorption by La-based adsorbents. It should be carried out to further develop La-based materials with high adsorption capacity and good regeneration ability. Meanwhile, studies have been conducted on the reuse of phosphate after desorption, which needs more attention in future research.

Functional group modified 1D interpenetrated metal-organic frameworks on perfluorooctanoic acid adsorption: Experimental and theoretical calculation study

Functional groups modified metal-organic frameworks (MOFs) was synthesized via a pre-tailor method and served as an adsorbent for perfluorooctanoic acid (PFOA) removal. The material was characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction and N₂ sorption-desorption. Monte Carlo simulation and molecular dynamics are derived to predict the possible molecular packing and adsorption mechanism. The Hirshfeld surface with reduced density gradient analysis demonstrates that PFOA is adsorbed on MOF-X mainly affected by van der Waals interactions and steric effects. Adsorption kinetics and isotherms were investigated on the basis of a static experiment. The pseudo-second-order kinetic model and Langmuir isotherm were fitted well to characterize adsorption process. Hereinto, amino-modified MOFs reached the highest adsorption efficiency and the maximum capacity was 185.6 mg/g. Combing the experimental data with theoretical simulation, results indicated that functional group modification is an effective approach to alter the crystal structure and then affect the adsorptive properties of MOFs.

Biochar-based composites for remediation of polluted wastewater and soil environments: Challenges and prospects

Pharmaceuticals, heavy metals, pesticides, and dyes are the main environmental contaminants that have serious effects on both land and aquatic lives and necessitate the development of effective methods to mitigate these issues. Although some conventional methods are in use to tackle soil contamination, but biochar and biochar-based composites represent a reliable and sustainable means to deal with a spectrum of toxic organic and inorganic pollutants from contaminated environments. The capacity of biochars and derived constructs to remediate inorganic dyes, pesticides, insecticides, heavy metals, and pharmaceuticals from environmental matrices is attributed to their extensive surface area, surface functional groups, pore size distribution, and high sorption capability of these pollutants in water and soil environments. Application conditions, biochar feedstock, pyrolysis conditions and precursor materials are the factors that influence the capacity and functionality of biochar to adsorb pollutants from wastewater and soil. These factors, when improved, can benefit biochar in agrochemical and heavy metal remediation from various environments. However, the processes involved in biochar production and their influence in enhancing pollutant sequestration remain unclear. Therefore, this paper throws light on the current strategies, operational conditions, and sequestration performance of biochar and biochar-based composites for agrochemical and heavy metal in soil and water environments. The main challenges associated with biochar preparation and exploitation, toxicity evaluation, research directions and future prospects for biochar in environmental remediation are also outlined.

Acid Neutralization and Immune Regulation by Calcium-Aluminum-Layered Double Hydroxide for Osteoporosis Reversion

Osteoporosis is a kind of global chronic bone disease characterized by progressive loss of bone mass and bone quality reduction, leading to a largely increased risk of bone fragility. In clinics, the current treatment of osteoporosis relies on the inhibition of bone damage by osteoclasts but ignores the function of immune cells in the progress of osteoporosis, leading to much compromised therapeutic efficacy. In this work, a highly effective osteoporosis-immunotherapeutic modality is established for the treatment of osteoporosis based on acid neutralization in synergy with immune microenvironment regulation by a specially designed nanocatalytic medicine, calcein functionalized calcium-aluminum-layered double hydroxide (CALC) nanosheets. Briefly, the mildly alkaline CALC nanosheets could neutralize the acidic microenvironment of osteoporosis accompanying the acidity-responsive LDH degradation. Subsequently, calcium phosphate nanoparticles (CAPs) are generated by the reaction between the released Ca²⁺ from LDH degradation and endogenous phosphates, resulting in M2 phenotype anti-inflammatory differentiation of bone macrophages through a c-Maf transcriptional factor pathway and the following activity enhancements of regulatory T cells (T_reg) and the deactivation of T helper 17 cells (T_H17). Both in vitro and in vivo results show an excellent therapeutic efficacy on osteoporosis featuring a significant BV/TV (%) enhancement of femurs from 6.2 to 10.7, demonstrating high feasibility of this therapeutic concept through the combined acid neutralization and immune regulation. Such an inorganic nanomaterial-based strategy provides a novel, efficient, and biosafe therapeutic modality for intractable osteoporosis treatment, which will benefit patients suffering from osteoporosis.

Enhanced phosphate removal and potential recovery from wastewater by thermo-chemically calcinated shell adsorbents

Shell from the seafood processing industry is an under-utilised waste resource worldwide. Calcite, the major component of shell is commonly used in wastewater treatment for the removal of phosphorus (P). Here, mussel and oyster shell-based adsorbents (MSB and OSB) were used for removal of P as phosphate (PO₄^3-) from aqueous solution and secondary wastewater, following preparation through chemical calcination at 700 °C. Batch adsorption experiments were carried out to identify the effects of various operating parameters (e.g., pH, dosage, contact time, initial concentration of P ions, co-existing ions), while a desorption study helped to understand the availability of the bonded P. The optimal contact time for PO₄^3- removal was 120 min using both adsorbents with the dose at 200 mg. Characterisation of the adsorbent was performed using SEM-EDX, pH_pzc, BET, FTIR and XRD. The XRD analysis showed that both calcite and lime were present on the surface of the shell particles. P was adsorbed effectively through inner-sphere complexation and surface microprecipitation mechanisms, while an enhanced maximum P adsorption capacity of 12.44 mg/g for MSB and 8.25 mg/g for OSB was reached. The Redlich-Peterson isotherm model fitted well with the equilibrium isotherm data (R² ≥ 0.97) which also suggested a heterogenic surface. The desorption study (on the saturated adsorbent) found that ~97% of bonded P could be plant available in soil. These results suggest that a shell-based adsorbent can serve as a promising material for P removal from real wastewater effluent and subsequently could be used as a soil conditioner.

Enhanced remediation of Cd-contaminated soil using electrokinetic assisted by permeable reactive barrier with lanthanum-based biochar composite filling materials

Electrokinetic remediation (EK) combined with a permeable reactive barrier (PRB) is a relatively new technique for efficiently remediating Cd-contaminated soil in situ. Eupatorium adenophorum, which is a malignant invasive plant, was used to synthesise biochar and a novel lanthanum-based biochar composite (LaC). The biochar and LaC were used as cheap and environmentally benign PRB filling materials to remediate simulated and real Cd-contaminated soils. The pH and residual Cd concentration in the simulated contaminated soil during remediation gradually increased from the anode to the cathode used to apply an electric field to the EK-PRB system. However, the soil conductivity changed in the opposite way, and the current density first increased and then decreased. For simulated contaminated soils with initial Cd concentrations of 34.9 and 100.6 mg kg^-1, the mean Cd removal rates achieved using LaC were 90.6% and 89.3%, respectively, which were significantly higher than those of biochar (P < 0.05). Similar results were achieved using natural soils from mining area and polluted farmland, and the Cd removal rates were 66.9% and 72.0%, respectively. Fourier-transform infrared and X-ray photoelectron spectroscopy indicated that there were many functional groups on the LaC surfaces. The removal mechanism of EK-PRB for Cd in contaminated soil includes electromigration, electroosmotic flow, surface adsorption, and ion exchange. The results indicated that the LaC could be used in the EK-PRB technique as a cheap and 'green' material to efficiently decontaminate soil polluted with heavy metals.

Removal effects of a biomass bottom ash composite on tailwater phosphate and its application in a rural sewage treatment plant

Tailwater phosphate from sewage treatment plants and biomass bottom ash (BA) from power plants has become a global concern for the sustainable environmental development and resource management. However, there are large gaps in the understanding of the removal mechanisms and application conditions of BA on tailwater phosphate. In this study, the removal effect and mechanism of BA and its composites were fully discussed using a series of experiments, including adsorption, desorption, characterization, and incubation experiments. It was found that the combination of BA and red soil at a rate of 4:1 (C_BA) could remove 92.44% of phosphate from tailwater in 3-10 h. Its adsorption process was well fitted by the pseudo-second-order kinetic and Freundlich isotherm adsorption models. The mechanism of phosphate adsorption primarily included ligand exchange, physical adsorption, chemical precipitation, electrostatic attraction, and ion exchange. The C_BA could be used as a better substrate for constructed wetlands because it was effective under wide application conditions, which varying pH values (4.0-8.0), initial concentrations of tailwater phosphate (0.5-5.0 mg L^-1), and even extreme temperatures (heat and cold). Moreover, Hippuris vulgaris L. was optimized and combined with the C_BA to deeply remove 57.45-76.06% of phosphate from a rural sewage treatment plant. The phosphate concentration after treatment could reach below the limit values of the Grade III or IV standard (GB 3838-2002), though the C_BA contained and released phosphate. This study can help provide a recycling route for both BA and tailwater phosphate resources, extend the industrial chain of biomass power plants, and improve the surrounding water environment.

Simultaneous recovery of phosphate and degradation of antibiotics by waste sludge-derived biochar

Recovery of phosphorus (P) from wastewater has led to growing public concern considering its scarcity and future availability as well as its detrimental environmental impacts. However, the recovered P is inevitably contaminated with co-existing antibiotics like tetracycline (TC) and sulfamethazine (SMT) which will pose serious risks to the health of human and animals after being spread to the environment. In this study, we propose a novel scheme that can recover P from synthetic wastewater and at the same time degrade the co-existing antibiotics. To achieve such a goal, a series of biochar (BC) were prepared from calcination of waste sludge and were used both as the adsorbent for P recovery and as the catalyst for peroxymonosulfate (PMS) activation and antibiotic degradation. Results showed that the sludge source (i.e. S_m: municipal sludge, S_p: paper mill sludge), calcination atmosphere (i.e. air-deficient, N₂, vacuum) and temperature (i.e. 600 and 800 °C) exhibited significant influence on P adsorption capacity. Generally, the BC calcined in N₂ showed better P uptake, and increase of calcination temperature from 600 °C to 800 °C could further improve P uptake. Though BC_p-N-600 (prepared from S_p in N₂ at 600 °C) showed faster and higher P uptake (56.3 mg/g) than its counterpart BC_m-N-600 (33.2 mg/g), BC_m-N-600 showed stronger catalytic activity and more stable performance in the complex pollutant system (P + SMT). It was proposed that P was recovered primarily through the chemisorption and precipitation mechanism, while SMT was nearly completely degraded primarily by the ROS generated from PMS activation.

Wastewater post-coagulation sludge recycled as a multifunctional adsorbent via pyrolysis enhanced in carbon dioxide (CO2)

Massive wastewater post-coagulation sludge (WPCS) generated from the tertiary treatment facilities has been regarded as an environmentally burdensome waste. Herein, to take advantage of the abundant amounts of Al/Fe (hydr)oxides, the WPCS was converted into functional char via pyrolysis under CO₂ and N₂ atmosphere. The higher organic matter content and porous structure of WPCS than drinking water treatment sludge made it a more suitable precursor for biochar and adsorbent production. CO₂ expedited the thermolysis of the organics in WPCS and the Fe (hydr)oxides in WPCS further decreased the temperature of CO₂-mediated reaction. Therefore, the corresponding products outcompeted the chars in N₂, achieving ∼37% higher specific surface area, stronger aromaticity and more amorphous Al and Fe contents of 201.19 ± 2.25 and 27.03 ± 0.56 mg g^-1, accompanied by more loss of surface functional groups like carboxyl and hydroxyl. Accordingly, WPCS chars under CO₂ showed superior performance for removing phosphate (15.58 ± 0.19 mg g^-1), along with the adsorption of heavy metal (37.17 ± 1.25 mg g^-1 of Pb (II)) and dye (14.45 ± 0.11 mg g^-1 of methylene blue). In sum, this study proposes a win-win strategy to convert coagulation sludges into resources and a new candidate for multifunctional adsorbent production.

Removal of pharmaceuticals from water using sewage sludge-derived biochar: A review

In recent years, considerable attention has been paid to the beneficial utilization of sewage sludge to reduce the risks associated with sludge disposal. Besides other applications of sludge, biochar produced from sludge has also been employed for the elimination of various pollutants from water. This review critically evaluates the recent progress in applications of sludge-based biochar for the adsorption of pharmaceuticals from water. The synthesis techniques of biochar production from sludge and their effects on physicochemical characteristics of produced biochar are discussed. The removal of various pharmaceuticals by sludge-based biochar are described in detail, with the emphasis on the adsorption mechanism and their reusability potential. It is evident from the literature that sludge-based biochar has demonstrated excellent potential for the adsorption of numerous pharmaceuticals from the aqueous phase. The major hurdles and issues related to the synthesis of sludge-based biochar and applications are highlighted, with reference to the adsorption of pharmaceuticals. Finally, a roadmap is suggested along with future research directions to ensure the sustainable production of biochar from sludge and its applications in water treatment.

Recovery of NH4 +-N and PO4 3--P from urine using sludge-derived biochar as a fertilizer: performance and mechanism

Sludge-derived biochar (BS) was prepared by pyrolyzing municipal sludge at different temperatures and was used to recover NH4 +-N and PO4 3--P from urine. The effects of dosage, adsorption time, and urine concentration on the adsorption of NH4 +-N and PO4 3--P were investigated, and the adsorbed BS was used as a fertilizer to study its effect on the growth of pakchoi cabbage. The Elovich model was more consistent with the adsorption processes of NH4 +-N and PO4 3--P. Both the NH4 +-N and PO4 3--P adsorption isotherm model agreed with the Redlich-Peterson model. The Langmuir model showed that the largest adsorption capacity of BS600 for NH4 +-N and PO4 3--P could reach 114.64 mg g-1 and 31.05 mg g-1, respectively. The NH4 +-N adsorption mechanism of BS may have complexation with O-containing functional groups and precipitation reactions, while the removal mechanism of PO4 3--P was co-precipitation. The pot experiment demonstrated that adsorbed BS600 can better promote the growth of pakchoi cabbage with the same amount of addition. With the addition of 5% adsorbed BS600, the weight of cabbage was 64.49 g heavier than without the addition of BS600. This research provided theoretical support for the recovery of NH4 +-N and PO4 3--P from urine as a fertilizer.

Sewage sludge-derived biochar for the adsorptive removal of wastewater pollutants: A critical review

The production of biochar from sewage sludge pyrolysis is a promising approach to transform the waste resultant from wastewater treatment plants (WWTPs) to a potential adsorbent. The current review provides an up-to-date review regarding important aspects of sewage sludge pyrolysis, highlighting the process that results major solid fraction (biochar), as high-value product. Further, the physio-chemical characteristics of sewage-sludge derived biochar such as the elemental composition, specific surface area, pore size and volume, the functional groups, surface morphology and heavy metal content are discussed. Recent progress on adsorption of metals, emerging pollutants, dyes, nutrients and oil are discussed and the results are examined. The sewage sludge-derived biochar is a promising material that can make significant contributions on pollutants removal from water by adsorption and additional benefit of the management of huge volume of sewage. Considering all these aspects, this field of research still needs more attention from the researchers in the direction of the technological features and sustainability aspects.

Synthesis of nano-silica and biogenic iron (oxyhydr)oxides composites mediated by iron oxidizing bacteria to remove antimonite and antimonate from aqueous solution: Performance and mechanisms

Removal of antimony from wastewater is essential because of its potential harm to the environment and human health. Nano-silica and biogenic iron (oxyhydr)oxides composites (BS-Fe) were prepared by iron oxidizing bacteria (IOB) mediation and the batch adsorption experiments were applied to investigate antimonite (Sb(III)) and antimonate (Sb(V)) removal behaviors. By contrast, the synthetic BS-Fe calcined at 400 ℃ (BS-Fe-400) exhibited a large specific surface area (157.353 m²/g). The maximum adsorption capacities of BS-Fe-400 were 102.10 and 337.31 mg/g for Sb(III) and Sb(V), respectively, and experimental data fit well to the Langmuir isotherm and Temkin models, and followed the pseudo-second order kinetic model. Additionally, increasing pH promoted Sb(III) adsorption, while inhibited the adsorption of Sb(V), indicating that electrostatic attraction made a contribution to Sb(V) adsorption. Moreover, different co-existing ions showed different effects on adsorption. Characterization techniques of FTIR and XPS indicated that the main functional groups involved in the adsorption were -OH, C-O, CO, C-C, etc. and Sb(III) and Sb(V) may bind to iron (oxyhydr)oxides via the formation of inner-sphere complexes. The present work revealed that the synthetic BS-Fe-400 by nano-silica and biogenic iron (oxyhydr)oxides held great application potential in antimony removal from wastewater.

Rare earth elements (REE) for the removal and recovery of phosphorus: A review

There is little doubt that 'rock phosphate' reserves are decreasing, with phosphorus (P) peak to be reached in the coming decades. Hence, removal and recovery of phosphorus (P) from alternative nutrient-rich waste streams is critical and of great importance owing to its essential role in agricultural productivity. Adsorption technique is efficient, cost-effective, and sustainable for P recovery from waste streams which otherwise can cause eutrophication in receiving waters. As selective P sorption using rare earth elements (REE) are gaining considerable attention, this review extensively focuses on P recovery by utilising a range of REE-incorporated adsorbents. The review briefly provides existing knowledge of P in various waste streams, and examines the chemistry and behaviour of REE in soil and water in detail. The impact of interfering ions on P removal using REE, adsorbent regeneration for reuse, and life cycle assessment of REE are further explored. While it is clear that REE-sorbents have excellent potential to recover P from wastewaters and to be used as fertilisers, there are gaps to be addressed. Future studies should target recovery and reuse of REE as P fertilisers using real wastewaters. More field trials of synthesized REE-sorbents are highly recommended before practical application.

Biomass as source for hydrochar and biochar production to recover phosphates from wastewater: A review on challenges, commercialization, and future perspectives

Excessive phosphate run-off with total phosphorus concentration greater than 20 μg P L^-1 triggers the growth of harmful algal species in waterbodies and potentially leads to eutrophication. This has severe negative implications on aquatic environment and impacts human health. The annual economic impact of harmful algal blooms is reported to be as high as $25 million for public health and commercial fishery sector, $29 million for recreation/tourism sector and $2 million for monitoring and management. Adsorption is widely considered as an effective and economic strategy to achieve extremely low concentration of phosphorus. The char produced by valorizing various waste biomasses have been gaining attention in phosphorus remediation owing to their availability, their ability to regenerate and reuse. This review paper exclusively focuses on utilizing hydrochar and biochar synthesized from waste biomass, respectively, through hydrothermal carbonization and slow pyrolysis to mitigate phosphorus concentration and potential strategies for handling the spent char. The key mechanisms involved in phosphate adsorption are electrostatic interaction, ion exchange and complexation. The maximum adsorption capacity of hydrochar and biochar ranges from 14-386 mg g^-1 and 3-887 mg g^-1, respectively. Hydrochar and biochar are cost-effective alternative to commercial activated carbon and spent char can be used for multiple adsorption cycles. Furthermore, extensive research studies on optimizing the feedstock, reaction and activation conditions coupled with technoeconomic analysis and life cycle assessment could pave way for commercialization of char-based adsorption technology.

Biochar for agronomy, animal farming, anaerobic digestion, composting, water treatment, soil remediation, construction, energy storage, and carbon sequestration: a review

In the context of climate change and the circular economy, biochar has recently found many applications in various sectors as a versatile and recycled material. Here, we review application of biochar-based for carbon sink, covering agronomy, animal farming, anaerobic digestion, composting, environmental remediation, construction, and energy storage. The ultimate storage reservoirs for biochar are soils, civil infrastructure, and landfills. Biochar-based fertilisers, which combine traditional fertilisers with biochar as a nutrient carrier, are promising in agronomy. The use of biochar as a feed additive for animals shows benefits in terms of animal growth, gut microbiota, reduced enteric methane production, egg yield, and endo-toxicant mitigation. Biochar enhances anaerobic digestion operations, primarily for biogas generation and upgrading, performance and sustainability, and the mitigation of inhibitory impurities. In composts, biochar controls the release of greenhouse gases and enhances microbial activity. Co-composted biochar improves soil properties and enhances crop productivity. Pristine and engineered biochar can also be employed for water and soil remediation to remove pollutants. In construction, biochar can be added to cement or asphalt, thus conferring structural and functional advantages. Incorporating biochar in biocomposites improves insulation, electromagnetic radiation protection and moisture control. Finally, synthesising biochar-based materials for energy storage applications requires additional functionalisation.

Phosphate adsorption characteristics of La(OH)3-modified, canna-derived biochar

La(OH)₃-modified canna biochar (CBC-La) was prepared by a coprecipitation method (dipping method), and its phosphate adsorption characteristics were investigated. The results show that the pseudo-second-order kinetics and the Langmuir model can be used to describe the adsorption process with a high level of accuracy. Adsorption equilibrium could be reached at 8 h, at which point the maximum adsorption capacity was shown to be 37.37 mg/g. CBC-La has excellent phosphate adsorption capacity in the middle to low concentrations (≤50 mg/L), and its removal rate can exceed 99 %. CBC-La also has wide pH adaptability (3-9) and a strongly selective adsorption performance. Notably, it can still maintain a removal rate of over 99.8 % in the presence of certain anions (NO₃^-, HCO₃^-, and CO₃^2-), and the presence of NH₄⁺ has a synergistic effect on the adsorption process. Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements demonstrate that the main mechanisms of CBC-La phosphate adsorption are electrostatic adsorption, ion exchange, ligand exchange and inner sphere complexation.

Removal of phosphate from aqueous solution by chitosan coated and lanthanum loaded biochar derived from urban dewatered sewage sludge: adsorption mechanism and application to lab-scale columns

A lanthanum modified sludge biochar chitosan (La-SBC-CS) microsphere was successfully synthesized by dropping sludge biochar (BC) and chitosan into a lanthanum chloride solution. Batch adsorption experiments were conducted to investigate the adsorption kinetics and isotherm. Application of continuous phosphate removal was achieved via lab-scale column reactors. The phosphate adsorption equilibrium data of the La-SBC-CS fitted well with the Freundlich isotherm, with a maximum adsorption amount of 81.54 mg p/g at 25 °C. Characterization of the adsorbent using scanning electron microscopy analysis (SEM), X-ray energy spectrum analysis (EDS), X-ray diffraction analysis (XRD) and Fourier infrared analysis (FTIR) techniques suggested that the possible adsorption mechanisms were electrostatic interaction, ligand exchange and complexation. The La-SBC-CS kept 76.37% phosphate removal efficiency after eight recycles. The results of continuous column reactor experiment demonstrated that the breakthrough time increased with an increase in adsorbent filling height, while it decreased with an increase in initial phosphate concentration or flow velocity. The Yoon model was applied to the continuous experimental data to predict breakthrough curves and determined the characteristic adsorption parameters for process design. This study indicated the potential for the practical application of La-SBC-CS in phosphate removal from wastewater.

Biochar application in organics and ultra-violet quenching substances removal from sludge dewatering leachate for algae production

Algae production in nutrient rich sludge dewatering leachate after biogas production is a promising option for wastewater treatment plants. However, the ultra-violet (UV) absorbing characteristic of UV-quenching substances (UVQS) existing in these waters can notably reduce the light transmission within the liquid body. The present work demonstrates a comparative adsorptive removal of UVQS, and other organic substances (expressed as COD and TOC) onto the "acid catalyst" functionalised adsorbent (PPhA) and commercial activated carbon (CAC) from leachate originating from leftover sludge dewatering after biogas production. Laboratory scale column studies were performed to investigate the adsorption performance of selected parameters. The PPhA increased the UV transmittance of leachate more than 4 times and outperformed CAC. Bed Depth Service Time and Yan models were used on the experimental data in order to estimate the maximum adsorption capacity and evaluate the characteristics of the fixed-bed. The PPhA equilibrium uptake of COD and TOC amounted to 5.7 mg/g and 0.9 mg/g, respectively. The postulated removal mechanism in environmentally relevant conditions (e.g., pH neutral) suggested a complex interaction between the biochar and organic macromolecules. Diluted phosphoric acid solution (0.01 mol/L) was successfully used for the column regeneration. Beside the UVQS, PPhA showed affinity towards toxic heavy metals (e.g., Pb, Ni, Co) pointing out the rich surface chemistry of the PPhA. Based on the obtained results and successfully implemented scale-up methodology, the low-cost PPhA adsorbent might effectively compete with the CAC as a highly efficient platform in wastewaters leachate processing.