Synthetic organic dyes as contaminants of the aquatic environment and their implications for ecosystems: A review

Fabrication of SERS composite substrates using Ag nanotriangles-modified SiO2 photonic crystal and the application of malachite green detection

A novel surface-enhanced Raman scattering (SERS) composite substrates on the basis of Ag triangular nanoplates(Ag TNPs)-modified SiO2 photonic crystals (PC) is fabricated and applied to the SERS detection of malachite green (MG). It consists of uniformly arranged Ag TNP@SiO2, a new PC. Notably, Ag TNP are uniformly aligned on the SiO2 surface, forming a three-dimensional high-density hotspot nanostructure. With the tip "hot spots" of Ag TNPs, Bragg diffraction of SiO2 and coupling enhancement between Ag TNPs and SiO2, the SERS enhancement of this composite substrates was multiplied. The effect on the SERS of Ag TNP@SiO2 composite substrate was systematically optimized by tuning Ag TNP size, size of SiO2 microspheres, coverage of Ag TNPs on SiO2 and fabrication method of Ag TNPs and PC. Moreover, the uniform of SERS composite substrates and Raman signal was dramatically increased by the method of vertical deposition. Eventually, the SERS composite substrates were employed in MG detection. Its broad detection range of 1 pM-1 μM and low limit of detection (LOD) of 0.49 pM indicated acceptable sensitivity and repeatability. This work illustrates the promising applicability in food safety analysis based on SERS composite substrates composed by Ag TNP@SiO2 with numerous SERS enhancements and excellent stability.

Development of inorganic and mixed matrix membranes for application in toxic dyes-contaminated industrial effluents with in-situ treatments

Dyes are the most ubiquitous organic pollutants in industrial effluents. They are highly toxic to both plants and animals; thus, their removal is paramount to the sustainability of ecosystem. However, they have shown resistance to photolysis and various biological, physical, and chemical wastewater remediation processes. Membrane removal technology has been vital for the filtration/separation of the dyes. In comparison to polymeric membranes, inorganic and mixed matrix (MM) membranes have shown potentials to the removal of dyes. The inorganic and MM membranes are particularly effective due to their high porosity, enhanced stability, improved permeability, higher enhanced selectivity and good stability and resistance to harsh chemical and thermal conditions. They have shown prospects in filtration/separation, adsorption, and catalytic degradation of the dyes. This review highlighted the advantages of the inorganic and MM membranes for the various removal techniques for the treatments of the dyes. Methods for the membranes production have been reviewed. Their application for the filtration/separation and adsorption have been critically analyzed. Their application as support for advanced oxidation processes such as persulfate, photo-Fenton and photocatalytic degradations have been highlighted. The mechanisms underscoring the efficiency of the processes have been cited. Lastly, comments were given on the prospects and challenges of both inorganic and MM membranes towards removal of the dyes from industrial effluents.

Remediation of pharmacophoric laboratory waste by using biodegradable carbon nanoparticles of bacterial biofilm origin

Research laboratories generate a broad range of hazardous pharmacophoric chemical contaminants, from drugs to dyes used during various experimental procedures. In the recent past, biological methods have demonstrated great potential in the remediation of such contaminants. However, the presence of pharmacophoric chemicals containing antibiotics, xenobiotics, and heavy metals suppresses the growth and survivability of used microbial agents, thus decreasing the overall efficiency of biological remediation processes. Bacterial biofilm is a natural arrangement to counter some of these inhibitions but its use in a systemic manner, portable devices, and pollutant remediation plants post serious challenges. This could be countered by synthesizing a biodegradable carbon nanoparticle from bacterial biofilm. In this study, extracellular polymeric substance-based carbon nanoparticles (Bio-EPS-CNPs) were synthesized from bacterial biofilm derived from Bacillus subtilis NCIB 3610, as a model bacterial system. The produced Bio-EPS-CNPs were investigated for physiochemical properties by dynamic light scattering, optical, Fourier-transformed infrared, and Raman spectroscopy techniques, whereas X-ray diffraction study, scanning electron microscopy, and transmission electron microscopy were used to investigate structural and morphological features. The Bio-EPS-CNPs exhibited negative surface charge with spherical morphology having a uniform size of sub-100 nm. The maximum remediation of some laboratory-produced pharmacophoric chemicals was achieved through a five-round scavenging process and confirmed by UV/Vis spectroscopic analysis with respect to the used pharmacophore. This bioinspired remediation of used pharmacophoric chemicals was achieved through the mechanism of surface adsorption via hydrogen bonding and electrostatic interactions, as revealed by different characterizations. Further experiments were performed to investigate the effects of pH, temperature, stirring, and the protocol of scavenging to establish Bio-EPS-CNP as a possible alternative to be used in research laboratories for efficient removal of pharmacophoric chemicals by incorporating it in a portable, filter-based device.

Freezing-enhanced degradation of azo dyes in the chloride-peroxymonosulfate system

In this study, we investigated the freezing-induced acceleration of dye bleaching by chloride-activated peroxymonosulfate (PMS). It has been observed that the oxidation of chloride by PMS generates a free chlorine species, such as hypochlorous acid (HOCl), under mild acidic and circumneutral pH condition. This process is the major reason for the enhanced oxidation capacity for electron-rich organic compounds (e.g., phenol) in the chloride-PMS system. However, we demonstrated that the chloride-PMS system clearly reduced the total organic carbon concentration (TOC), whereas the HOCl system did not lead to decrease in TOC. Overall, the chemical reaction is negligible in an aqueous condition if the concentrations of reagents are low, and freezing the solution accelerates the degradation of dye pollutants remarkably. Most notably, the pseudo-first order kinetic rate constant for acid orange 7 (AO7) degradation is approximately 0.252 h-1 with 0.5 mM PMS, 1 mM NaCl, initial pH 3, and a freezing temperature of -20 °C. AO7 degradation is not observed when the solution is not frozen. According to a confocal Raman-microscope analysis and an experiment that used an extremely high dose of reactants, the freeze concentration effect is the main reason for the acceleration phenomenon. Because the freezing phenomenon is spontaneous at high latitudes and at mid-latitudes in winter, and the chloride is ubiquitous elsewhere, the frozen chloride-PMS system has potential as a method for energy-free and eco-friendly technology for the degradation of organic pollutants in cold environments.

A mechanochemically synthesized Schiff-base engineered 2D mixed-linker MOF for CO2 capture and cationic dye removal

Developing synthetic strategies for smart materials for the adsorption and separation of toxic chemicals is of great importance. Metal-organic frameworks (MOFs) have been proven to be outstanding adsorbent materials that possess excellent pollutant removal performances in wastewater treatment, including dye recycling. In this work, a neutral Cd(II) based 2D framework with a dual ligand strategy involving -OH functionalized 5-hydroxyisophthalic acid (5-OH-H2IPA) and the amide decorated Schiff base ligand (E)-N'-(pyridin-4-ylmethylene)isonicotinohydrazide (L) has been synthesized by different synthetic routes and characterized by various analytical methods. Thus, crystals of {[Cd(5-OH-IPA)(L)]·CH3OH}n synthesized via diffusion (ADES-7D) and the phase pure bulk product synthesized by conventional reflux (ADES-7C) and the mechanochemical grinding method (ADES-7M) have been established using PXRD data of the respective product showing identical simulated SXRD data to those of ADES-7D. The mechanochemically synthesized ADES-7M possesses a better surface area and CO2 adsorption capability compared to ADES-7C, which is also supported by electron microscopy and particle size measurements. Furthermore, ADES-7 can be used as an efficient adsorbent material for the reversible, selective adsorption (42-99%) and separation of the cationic dyes malachite green (MG), methyl violet (MV), methylene blue (MB), and rhodamine B (RhB) from the mixture of cationic/anionic dyes (methyl orange (MO) and bromocresol green (BCG)) in the aqueous phase. Specifically, ADES-7M possesses better dye capture capability compared to ADES-7C, even in the case of the bigger dye RhB with adsorption differences of 2.38 to 1.01 mg g-1, respectively. The dye adsorption kinetics follows pseudo-second-order kinetics, and the dye adsorption isotherm fits well with the Langmuir/Freundlich adsorption isotherm models. The probable mechanism of adsorption involving the supramolecular interaction between the host MOF and the guest dye has also been proposed.

Chromogenic fusion proteins as alternative textiles dyes

The widespread adoption of fast fashion has led to a significant waste problem associated with discarded textiles. Using proteins to color textiles can serve as a sustainable alternative to chemical dyes as well as reduce the demand for new raw materials. Here, we explore the use of chromogenic fusion proteins, consisting of a chromoprotein and a carbohydrate-binding module (CBM), as coloring agents for cellulose-based textiles such as cotton. We examined the color properties of chromoproteins AeBlue, SpisPink and Ultramarine alone and fused to CBM under various conditions. AeBlue, SpisPink and Ultramarine exhibited visible color between pH 4-9 and temperatures ranging from 4 to 45℃. Fusing CBM Clos from Clostridium thermocellum and CBM Ch2 from Trichoderma reesei to the chromoproteins had no effect on the chromoprotein color properties. Furthermore, binding assays showed that chromoprotein fusions did not affect binding of CBMs to cellulosic materials. Cotton samples bound with Ultramarine-Clos exhibited visible purple color that faded progressively over time as the samples dried. Applying 10% 8000 polyethylene glycol to cotton samples markedly preserved the color over extended periods. Overall, this work highlights the potential of chromoprotein-CBM fusions for textile dying which could be applied as a color maintenance technology or for reversible coloring of textiles for events or work wear, contributing to sustainable practices and introducing new creative opportunities for the industry.

Characterization of banned colorants in cosmetics: A tandem mass-based molecular networking approach

Colorants have been a staple in the cosmetics industry for a considerable time, although certain varieties have been banned owing to health risks. Detecting and confirming these banned colorants simultaneously poses several challenges when employing LC-MS/MS. Molecular networking is a promising analytical technology that can be used to predict the structure of components and the correlation between them using structural and MS/MS spectral similarities. Molecular networking entails assessing the number of fragmented ions and the cosine score (the closer it is to one, the higher the similarity). In this study, we developed and verified a method for the simultaneous quantitative analysis of the 26 banned colorants in cosmetics using LC-MS/MS. Additionally, we propose a novel approach that combines LC-Q-TOF-MS and molecular networking technology to detect banned colorants in cosmetics. For successful molecular networking, a minimum of six fragment ions with cosine scores exceeding 0.5 is required. We developed a screening method for characterizing banned colorants using molecular networking based on LC-TOF-MS results for 26 banned colorants. Furthermore, we demonstrated that our established method can be used for screening by analyzing actual cosmetics (eyebrow tattoo, lipstick tattoo, and hair tint) spiked with three non-targeted banned colorants with similar structures (m/z 267.116, 315.149, and 345.157) in cosmetics. The combination of molecular networking techniques and LC-MS/MS proves highly advantageous for the swift characterization and screening of non-targeted colorants in cosmetics.

High-performance Ag-TiO2 nanoparticle composite catalyst synthesized by pulsed laser ablation in liquid: properties, mechanism and preparation studies

Precious metal doping can effectively improves the catalytic performance of TiO2. In this study, pulsed laser ablation in liquid (PLAL) is employed to integrate preparation with doping and control composite nanoparticle products by adjusting the laser action time to synthesise Ag-TiO2 composite nanoparticles with high catalytic performance. The generation and evolution of Ag-TiO2 nanoparticles are investigated by analysing particle size, microscopic morphology, crystalline phase, and other characteristics. The generation and doped-morphology evolution of composite nanoparticles are simulated based on thermodynamics, and the optimisation of Ag-doped structure on the composite nanomaterials is investigated based on density functional theory. The effect of Ag-TiO2 structural properties on its performance is examined under different catalytic conditions to determine optimal degradation conditions. In this study, the effect of laser ablation time on the doped structure during PLAL is analysed, which is of further research significance in exploring the structural evolution law of laser and composite nanoparticles, multi-variate catalytic performance testing, reduction of photogenerated carrier complexation rate, and expansion of its spectral absorption range, thereby providing the basis for practical production.

Constructing the synergistic effects of chitosan and ionic liquid on SPEEK polymer for efficient adsorption of crystal violet dye

In the study, a novel chitosan biopolymer and 1-ethyl-3-methylimidazolium tetrafluoroborate ionic liquid (IL)-incorporated sulfonated poly (ether ether ketone) (SPEEK) composite (Ch-IL@SPEEK) was prepared for adsorption of cationic crystal violet (CV) dye. The proposed composite was well characterized by several techniques. CV adsorption performance was examined via batch studies by varying various variables involving adsorbent dosage, contact time pH and temperature. The isotherm results were demonstrated the adsorption characters of the processes were Langmuirian. The maximum adsorption capacity was determined as 77.66 mg g-1 for the composite which was significantly higher than SPEEK (qmax = 45.36 mg g-1). The determined equilibrium time of the operated system was 360 min and the kinetic model was assessed as Elovich. At low pHs the protonated surface groups repelled the positively charged CV and the adsorption rate increased with increasing pH. The process is spontaneous and favorable as it proceeds via endothermic interactions. Furthermore, even at the end of 5 successful adsorption cycles, 77.86 % CV removal was obtained. Remarkable efficiencies were also achieved in the removal performance of different organic pollutants. Based on the reported results, Ch-IL@SPEEK composite were exhibited as an impressive adsorbent material for adsorption processes.

Review of carbon dot-hydrogel composite material as a future water-environmental regulator

As water pollution and scarcity pose severe threats to the sustainable progress of human society, it is important to develop a method or materials that can accurately and efficiently detect pollutants and purify aquatic environments or exploit marine resources. The compositing of photoluminescent and hydrophilic carbon dots (CDs) with hydrogels bearing three-dimensional networks to form CD-hydrogel composites to protect aquatic environments is a "win-win" strategy. Herein, the feasibility of the aforementioned method has been demonstrated. This paper reviews the recent progress of CD-hydrogel materials used in aquatic environments. First, the synthesis methods for these composites are discussed, and then, the composites are categorized according to different methods of combining the raw materials. Thereafter, the progress in research on CD-hydrogel materials in the field of water quality detection and purification is reviewed in terms of the application of the mechanisms. Finally, the current challenges and prospects of CD-hydrogel materials are described. These results are expected to provide insights into the development of CD-hydrogel composites for researchers in this field.

An eco-friendly chitosan-genipin/SiO2 composite for reactive orange 16 dye removal: Insights into adsorption statistical modeling and mechanism

The present work develops an effective bioadsorbent of cross-linked chitosan-genipin/SiO2 adsorbent (CHI-GNP/SiO2). The developed CHI-GNP/SiO2 was employed for the removal of organic dye (reactive orange 16, RO16) from simulated wastewater. The optimization of the fundamental adsorption variables (CHI-GNP/SiO2 dose, time, and pH) via the Box-Behnken design (BBD) was attained for achieving maximal adsorption capacity and high removal efficiency. The good agreement between the Freundlich isotherms and empirical data of RO16 adsorption by CHI-GNP/SiO2 indicates that the adsorption process follows a multilayer adsorption mechanism. The reasonable agreement between the pseudo-second-order model and the kinetic data of RO16 adsorption by CHI-GNP/SiO2 was obtained. The maximum RO16 adsorption capacity (qmax) of CHI-GNP/SiO2 was identified to be 57.1 mg/g. The adsorption capacity of CHI-GNP/SiO2 is attributed to its unique surface properties, including its highly porous structure and the presence of functional groups such as amino and hydroxyl groups. According to the results of this investigation, CHI-GNP/SiO2 has the potential to be an adsorbent for the removal of acidic dyes from wastewater.

Decolorization and degradation of crystal violet dye by electron beam radiation: Performance, degradation pathways, and synergetic effect with peroxymonosulfate

Ionizing radiation (mainly including gamma ray and electron beam) technology provides a more efficient and ecological option for dye-containing wastewater treatment, which is supported by its successful achievements in industrial-scale applications. However, the degradation pathway of triphenylmethane dyes by radiation technology is still unclear. In this study, crystal violet (CV) was selected as representative cationic triphenylmethane dye, the decolorization and degradation performance by electron beam radiation technology was systematically evaluated. The results showed that CV can be efficiently decolorized and mineralized by radiation, and its degradation kinetics followed the first-order kinetic model. The effect of inorganic anions and chelating agents commonly existed in dye-containing wastewater on CV decolorization and total organic carbon (TOC) removal was explored. Quenching experiments, density functional theory (DFT) calculation and high performance liquid chromatography mass spectrometry (HPLC-MS) analysis were employed to reveal CV decolorization and degradation mechanism and pathway, which mainly included N-demethylation, triphenylmethane chromophore cleavage, ring-opening of aromatic products and further oxidation to carboxylic acid, and mineralization to CO2 and H2O. Additionally, electron beam radiation/PMS process was explored to decrease the absorbed dose required for decolorization and degradation, and the synergetic effect of radiation with PMS was elucidated. More importantly, the findings of this study would provide the support for treating actual dyeing wastewater by electron beam radiation technology.

Multiphase electroextraction of malachite green from surface water and its determination using digital imaging and chemometric tools

This study introduces a novel method for the quantification of malachite green (MG), a pervasive cationic dye, in surface water by synergizing multiphase electroextraction (MPEE) with digital image analysis (DIA) and partial least square discriminant analysis. Aimed at addressing the limitations of conventional DIA methods in terms of quantitation limits and selectivity, this study achieves a significant breakthrough in the preconcentration of MG using magnesium silicate as a novel sorbent. Demonstrating exceptional processing efficiency, the method allows for the analysis of 10 samples within 20 min, exhibiting remarkable sensitivity and specificity (over 0.95 and 0.90, respectively) across 156 samples in both training and test sets. Notably, the method detects MG at low concentrations (0.2 µg L-1) in complex matrices, highlighting its potential for broader application in environmental monitoring. This approach not only underscores the method's cost-effectiveness and simplicity but also its precision, making it a valuable tool for the preliminary testing of MG in surface waters. This study underscores the synergy among MPEE, DIA, and chemometric tools, presenting a cost-efficient and reliable alternative for the sensitive detection of water contaminants.

Fundamental properties and sustainable applications of the natural zeolite clinoptilolite

This review explores a set of sustainable applications of clinoptilolite, a natural zeolite abundant around the world in different localities. Thanks to its physico-chemical properties this material is extremely versatile for several applications, ranging from environmental catalysis and CO2 removal to industrial and agricultural wastewater purification, aquaculture, animal feeding, and food industry but also medical applications and energy storage systems. Due to the presence of cations in its framework, it is possible to tune the material's features making it suitable for adsorbing specific compounds. Thus, this review aims to provide insight into developing new technologies based on the use of this material that is sustainable, not harmful for humans and animals, naturally abundant, and above all cost-effective. Furthermore, it is intended to promote the use of natural materials in various areas with a view to sustainability and to reduce as far as possible the use of chemicals or other materials whose synthesis process can have a polluting effect on the environment.

Smart pillar[5]arene-based PDMAEMA/PES beads for selective dye pollutants removal: design, synthesis, chemical-physical characterization, and adsorption kinetic studies

This article reports on the synthesis of an innovative smart polymer, P5-QPDMAEMA, opportunely developed with the aim of combining the responsiveness of PDMAEMA polymer and the host-guest properties of covalently linked pillar[5]arenes. Thanks to a traditional Non-Induced Phase Separation (NIPS) process performed at various coagulation pH, the blending of P5-QPDMAEMA with polyethersulfone gave rise to the formation of functional beads for the removal of organic dyes in water. Adsorption tests are carried out on all the produced blend-based beads by employing two representative dyes, the cationic methylene blue (MB), and the anionic methyl orange (MO). In particular, the P5-QPDMAEMA based beads, prepared at acidic pH, featured the best MO removal rate (i. e., 91.3 % after 150 minutes starting from a 20 mg ⋅ L-1 solution) and a high selectivity towards the removal of the selected anionic dye. Based on the adsorption kinetics and isotherm calculations, the pseudo-first order and Freundlich models were shown to be the most suitable to describe the MO adsorption behavior, achieving a maximum adsorption capacity of 21.54 mg ⋅ g-1. Furthermore, zwitterionic beads are obtained by a post-functionalization of the PDMAEMA and the P5-QPDMAEMA based beads, to test their removal capability towards both anionic and cationic dyes, as shown.

Efficient degradation and detoxification of structurally different dyes and mixed dyes by LAC-4 laccase purified from white-rot fungi Ganoderma lucidum

The purpose of this study is to evaluate the decolorization ability and detoxification effect of LAC-4 laccase on various types of single and mixed dyes, and lay a good foundation for better application of laccase in the efficient treatment of dye pollutants. The reaction system of the LAC-4 decolorizing single dyes (azo, anthraquinone, triphenylmethane, and indigo dyes, 17 dyes in total) were established. To explore the decolorization effect of the dye mixture by LAC-4, two dyes of the same type or different types were mixed at the same concentration (100 mg/L) in the reaction system containing 0.5 U laccase, and time-course decolorization were performed on the dye mixture. The combined dye mixtures consisted of azo + azo, azo + anthraquinone, azo + indigo, azo + triphenylmethane, indigo + triphenylmethane, and triphenylmethane + triphenylmethane. The results obtained in this study were as follows. Under optimal conditions of 30 °C and pH 5.0, LAC-4 (0.5 U) can efficiently decolorize four different types of dyes. The 24-hour decolorization efficiencies of LAC-4 for 800 mg/L Orange G and Acid Orange 7 (azo), Remazol Brilliant Blue R (anthraquinone), Bromophenol Blue and Methyl Green (triphenylmethane), and Indigo Carmine (indigo) were 75.94%, 93.30%, 96.56%, 99.94%, 96.37%, and 37.23%, respectively. LAC-4 could also efficiently decolorize mixed dyes with different structures. LAC-4 can achieve a decolorization efficiency of over 80% for various dye mixtures such as Orange G + Indigo Carmine (100 mg/L+100 mg/L), Reactive Orange 16 + Methyl Green (100 mg/L+100 mg/L), and Remazol Brilliant Blue R + Methyl Green (100 mg/L+100 mg/L). During the decolorization process of the mixed dyes by laccase, four different interaction relationships were observed between the dyes. Decolorization efficiencies and rates of the dyes that were difficult to be degraded by laccase could be greatly improved when mixed with other dyes. Degradable dyes could greatly enhance the ability of LAC-4 to decolorize extremely difficult-to-degrade dyes. It was also found that the decolorization efficiencies of the two dyes significantly increased after mixing. The possible mechanisms underlying the different interaction relationships were further discussed. Free, but not immobilized, LAC-4 showed a strong continuous batch decolorization ability for single dyes, two-dye mixtures, and four-dye mixtures with different structures. LAC-4 exhibited high stability, sustainable degradability, and good reusability in the continuous batch decolorization. The LAC-4-catalyzed decolorization markedly reduced or fully abolished the toxic effects of single dyes (azo, anthraquinone, and indigo dye) and mix dyes (nine dye mixtures containing four structural types of dyes) on plants. Our findings indicated that LAC-4 laccase had significant potential for use in bioremediation due to its efficient degradation and detoxification of single and mixed dyes with different structural types.

Microwave-assisted synthesis of ZnO structures for effective degradation of methylene blue dye under solar light illumination

The presence of dyes in wastewater poses a high risk to both human health and the environment due to their potential toxicity and ecological impacts. Zinc(ii) oxide is a low-cost, non-toxic material that can serve as a sustainable and effective solution to the global water pollution crisis. In this study, we propose a facile one-step synthesis of various ZnO structures by microwave irradiation. The primary goal of this study was to explore the morphology-dependent photocatalytic activity of various ZnO structures, as well as the impact of interfering anions on the Methylene Blue (MB) photodegradation under solar light illumination. Photocatalytic activity studies show that the sample denoted as 0.56 M-ZnO with a sheet-like structure has remarkable catalytic activity under solar light illumination, reaching ∼96.6% degradation of 30 mL MB solution (3 × 10-5 M) within 40 minutes. The BET specific surface area and band gap of the optimal 0.56 M-ZnO sample were observed to be 12.42 m2 g-1 and 2.89 eV, respectively. It was shown that the presence of anions like Cl-, NO3-, and HCO3- can reduce the catalytic activity of 0.56 M-ZnO structure to some extent, although more than 70% MB degradation can still be obtained under neutral pH conditions. The superior catalytic efficacy observed in the 0.56 M-ZnO photocatalyst can be attributed to its improved crystallinity, large surface area, and enhanced production of hydroxyl radicals. The low-cost synthesis, combined with high photocatalytic activity collectively underscores the efficiency and practical usability of produced ZnO photocatalysts for dye degradation.

A MXene Hydrogel-Based Versatile Microrobot for Controllable Water Pollution Management

The urgent demand for addressing dye contaminants in water necessitates the development of microrobots that exhibit remote navigation, rapid removal, and molecular identification capabilities. The progress of microrobot development is currently hindered by the scarcity of multifunctional materials. In this study, a plasmonic MXene hydrogel (PM-Gel) is synthesized by combining bimetallic nanocubes and Ti3C2Tx MXene through the rapid gelation of degradable alginate. The hydrogel can efficiently adsorb over 60% of dye contaminants within 2 min, ultimately achieving a removal rate of >90%. Meanwhile, the hydrogel exhibits excellent sensitivity in surface enhanced Raman scattering (SERS) detection, with a limit of detection (LOD) as low as 3.76 am. The properties of the plasmonic hydrogel can be further adjusted for various applications. As a proof-of-concept experiment, thermosensitive polymers and superparamagnetic particles are successfully integrated into this hydrogel to construct a versatile, light-responsive microrobot for dye contaminants. With magnetic and optical actuation, the robot can remotely sample, identify, and remove pollutants in maze-like channels. Moreover, light-driven hydrophilic-hydrophobic switch of the microrobots through photothermal effect can further enhance the adsorption capacity and reduced the dye residue by up to 58%. These findings indicate of a broad application potential in complex real-world environments.

Reuse of iron ore tailings as an efficient adsorbent to remove dyes from aqueous solution

In this work, an iron ore tailings sample (IOT), collected from a tailings dam in Minas Gerais, Brazil, was characterized. The IOT presented point of zero charge of ∼ 6, specific surface area of 4 m2 g-1, and was mainly composed of hematite and quartz. Subsequently, experiments were performed to evaluate the adsorption of an anionic dye, Direct Red 80 (DR80), and a cationic dye, Methylene Blue (MB), by the IOT, studying the effects of its dose (doseIOT) and the solution initial pH (pH0). The DR80 removal increased with the decrease of the pH0 while the opposite effect occurred in the experiments with the MB, suggesting the process is governed by the adsorption resulting from electrostatic forces. The increase in the doseIOT increased the DR80 and MB removal, which can be attributed to the greater availability of adsorption sites. Pseudo-second order kinetic (R2 > 0.9994) and the Langmuir equilibrium isotherm (R2 > 0.9842) models described well the DR80 adsorption by the IOT, being the reaction rate and maximum adsorption capacity higher at lower pH0. In a regeneration experiment, it was possible to desorb almost entirely the DR80 using a NaOH solution. Additionally, the regenerated IOT was able to adsorb the DR80, demonstrating its reusability. In a preliminary assay, the IOT decreased the colour of the textile wastewater sample at pH0 3. Therefore, the results indicate the potential use of IOT for removing electric-charged pollutants by adsorption, especially anionic ones under acidic conditions.

Valorization of Waste Watermelon Rinds as a Bio-adsorbent for Efficient Removal of Methylene Blue Dye from Aqueous Solutions

Nature-based solutions (NBSs) for remediation of various emerging contaminants have gained impetus during the last few decades. In the current study, watermelon (citrullus lanatus), a highly consumed seasonal fruit, was used as a feedstock waste biomass for biochar synthesis through valorization of watermelon rinds. The watermelon biochar (WM-BC) was synthesized through slow pyrolysis at 550°C under anoxic conditions. Langmuir model with R2>99, was found to best fit the adsorption isotherm, and the adsorption kinetics was best described by the pseudo-second-order model. Various characterization tools including FTIR, SEM, BET, XRD, and TEM were used to evaluate the surface morphology of the biochar. The removal efficiency increased from 35% (dosage = 0.4 g), to 81% at WM-BC dosage of 2 g. A maximum adsorption capacity of 115.61 mg/g was found. The results from kinetic and isotherm model model suggested that the adsorption was favorable and multilayer adsorption can be considered. The adsorption mechanism was found to be governed by the co-existing factors such as hydrogen bonding, electrostatic interactions, and aromatic interactions. Results suggest that WM-BC has high potential to be employed as an adsorbent for efficient remediation of methylene blue dyes from aqueous solutions.

Synthesis of Composite Sorbents with Chitosan and Varied Silica Phases for the Adsorption of Anionic Dyes

In this work, various types of silica materials were used for the synthesis of chitosan-silica composites. The composites were obtained using the chitosan (Ch) immobilization process from an aqueous solution on various silica phases, i.e., amorphous diatomite (ChAD), crystalline diatomite (ChCD), mesoporous silica MCM-41 (ChMCM), and mesoporous silica SBA-15 (ChSBA). Textural, structural, morphological, and surface properties of the materials were determined by using various measurement techniques, i.e., low-temperature adsorption/desorption isotherms of nitrogen, X-ray diffraction (XRD), small-angle X-ray scattering (SAXS), potentiometric titration, high-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The adsorption properties towards various anionic dyes, i.e., acid red 88 (AR88), acid orange 8 (AO8), and orange G (OG), were evaluated based on kinetic and equilibrium measurements. The ChSBA, ChAD, and ChMCM composites were characterized by relatively high adsorption capacities (am) for AR88, with values equal to 0.78, 0.71, and 0.69 mmol/g, respectively. These composites were also distinguished by the rapid AR88 adsorption rate, with the values of half-time parameter t0.5 equal to 0.35, 2.84, and 1.53 min, respectively. The adsorption equilibrium and kinetic data were analyzed by applying the generalized Langmuir isotherm and the multi-exponential equation (m-exp), respectively. An interaction mechanism between the dyes and the obtained materials was proposed.

Highly efficient and selective removal of anionic dyes from aqueous solutions using polyacrylamide/peach gum polysaccharide/attapulgite composite hydrogels with positively charged hybrid network

To avoid the weakness (lower adsorption rate and selectivity) of peach gum polysaccharide (PGP) and improve the adsorption performance of polyacrylamide (PAAm) hydrogel (lower adsorption capacity), in the present work, the PGP was chemically tailored to afford ammoniated PGP (APGP) and quaternized PGP (QPGP), and attapulgite (ATP) was bi-functionalized with cation groups and carbon‑carbon double bond. Then, PAAm/APGP and PAAm/QPGP/ATP hydrogels were synthesized via redox polymerization. The synthesis procedure and properties of hydrogels were traced by FTIR, SEM, XPS, TGA, TEM, and BET methods, and the dye adsorption performance of the hydrogels was evaluated using the new coccine (NC) and tartrazine (TTZ) aqueous solutions as the model anionic dyes. Effects of initial dye concentration, pH, and ionic strength on the adsorption were investigated. Compared with PAAm/APGP hydrogel, PAAm/APGP/ATP hydrogel exhibits higher adsorption rate, superior adsorption capacity, stability, and selectivity towards anionic dye. The adsorption process of PAAm/QPGP/ATP hydrogel reached equilibrium in about 20 min and followed the pseudo-second-order kinetic model and Langmuir isotherm. The adsorption capacities towards NC and TTZ of PAAm/QPGP/ATP hydrogel were calculated as 873.235 and 731.432 mg/g. This hydrogel adsorbent originating from PAAm, PGP, and ATP shows great promise for application in practical water treatment.

Iron-Carbon Nanospheres as Promising Material for Magnetic Assisted Adsorption and Separation of Impurities from a Liquid Phase

The composites containing various iron compounds and highly microporous carbon spheres were produced and investigated for structural and magnetic properties. Iron citrate, nitrate and chloride were used to prepare samples and the obtained products contained iron, iron carbide or magnetite. All the produced samples were characterized by high porosity and good magnetic properties. The coupling of the high porosity of carbon spheres with magnetic properties of iron compounds provides a potential application of the composites to removal of impurities from water, followed by a magnetic separation of the sorbent.

One-Step Synthesis of Polyethyleneimine-Grafted Styrene-Maleic Anhydride Copolymer Adsorbents for Effective Adsorption of Anionic Dyes

Wastewater containing organic dyes has become one of the important challenges in water treatment due to its high salt content and resistance to natural degradation. In this work, a novelty adsorbent, PEI-SMA, was prepared by grafting polyethyleneimine (PEI) onto styrene-maleic anhydride copolymer (SMA) through an amidation reaction. The various factors, such as pH, adsorbent dosage, contact time, dye concentration, and temperature, which may affect the adsorption of PEI-SMA for Reactive Black 5 (RB5), were systematically investigated by static adsorption experiments. The adsorption process of PEI-SMA for RB5 was more consistent with the Langmuir isotherm model and the pseudo-second-order model, suggesting a single-layer chemisorption. PEI-SMA exhibits excellent adsorption performance for RB5 dye, with a maximum adsorption capacity of 1749.19 mg g-1 at pH = 2. Additionally, PEI-SMA exhibited highly efficient RB5 competitive adsorption against coexisting Cl- and SO42- ions and cationic dyes. The adsorption mechanism was explored, and it can be explained as the synergistic effect of electrostatic interaction, hydrogen bonding and π-π interaction. This study demonstrates that PEI-SMA could act as a high performance and promising candidate for the effective adsorption of anionic dyes from aqueous solutions.

Biotransformation of the azo dye reactive orange 16 by Aspergillus flavus A5P1: Performance, genetic background, pathway, and mechanism

This study reports the strain Aspergillus flavus A5P1 (A5P1), which is with the capable of degrading the azo dye reactive orange 16 (RO16). The mechanism of RO16 degradation by A5P1 was elucidated through genomic analysis, enzymatic analysis, degradation pathway analysis and oxidative stress analysis. Strain A5P1 exhibited aerobic degradation of RO16, with optimal degradation at an initial pH of 3.0. Genomic analysis indicates that strain A5P1 possesses the potential for acid tolerance and degradation of azo dye. Enzymatic analysis, combined with degradation product analysis, demonstrated that extracellular laccase, intracellular lignin peroxidase, and intracellular quinone reductase were likely key enzymes in the RO16 degradation process. Oxidative stress analysis revealed that cell stress responses may participate in the RO16 biotransformation process. The results indicated that the biotransformation of RO16 may involves biological processes such as transmembrane transport of RO16, cometabolism of the strain with RO16, and cell stress responses. These findings shed light on the biodegradation of RO16 by A5P1, indicating A5P1's potential for environmental remediation.

Rational synthesis of two isostructural thiophene-containing metal-organic frameworks toward photocatalytic degradation of organic pollutants

In this work, thiophene moieties (as the crucial functional groups) have been successfully incorporated into the skeleton of metal-organic frameworks (MOFs) by using thienyl-substituted triazole ligands. Reaction of AgCF3SO3 with 3-phenyl-5-(2-thienyl)-1,2,4-triazole (PTTzH) or 3,5-bis(2-thienyl)-1,2,4-triazole (BTTzH) afforded two isostructural MOFs (AgTz-3 and AgTz-4) in gram-scale. AgTz-4 with higher thiophene content showed significantly stronger photocatalytic activity than AgTz-3 with lower thiophene content. Noteworthy, the photodegradation rate constants of AgTz-4 were 0.055 mg·L-1·min-1 for rhodamine B and 0.24 min-1 for salazosulfapyridine, which is comparable or even higher than some MOF-based materials reported in the literature. More importantly, AgTz-4 demonstrated good reusability and stability after four cycles of photodegradation. Our experimental results revealed that the enhanced photodegradation efficiency can be attributed to the increased light absorption capacity and optimized band structure of Ag-MOFs resulting from the introduction of thiophene groups into MOF structures.

Self-pigmenting textiles grown from cellulose-producing bacteria with engineered tyrosinase expression

Environmental concerns are driving interest in postpetroleum synthetic textiles produced from microbial and fungal sources. Bacterial cellulose (BC) is a promising sustainable leather alternative, on account of its material properties, low infrastructure needs and biodegradability. However, for alternative textiles like BC to be fully sustainable, alternative ways to dye textiles need to be developed alongside alternative production methods. To address this, we genetically engineer Komagataeibacter rhaeticus to create a bacterial strain that grows self-pigmenting BC. Melanin biosynthesis in the bacteria from recombinant tyrosinase expression achieves dark black coloration robust to material use. Melanated BC production can be scaled up for the construction of prototype fashion products, and we illustrate the potential of combining engineered self-pigmentation with tools from synthetic biology, through the optogenetic patterning of gene expression in cellulose-producing bacteria. With this study, we demonstrate that combining genetic engineering with current and future methods of textile biofabrication has the potential to create a new class of textiles.

Nontarget screening analysis of organic compounds in river sediments: a case study in the Taipu River of the Yangtze River Delta Region in China

Sediments are the vital fate of organic compounds, and the recognition of organic compounds in sediments is constructive in providing comprehensive and long-term information. In this study, a three-step nontarget screening (NTS) analysis workflow using comprehensive two-dimensional gas chromatography coupled with time-of-flight mass spectrometry (GC × GC-TOFMS) revealed the extensive existence of organic compounds in the Taipu River sediment. Organic compounds (705) were detected and divided into four structure-related groups or eight use-related classes. In the Taipu River's mainstream, a significant difference was found in the composition profiles of the identified organic compounds among various sites, demonstrating the organic compounds were more abundant in the midstream and downstream than in the upstream. Meanwhile, the hydrodynamic force was recognized as a potential factor influencing organic compounds' occurrence. Based on multiple statistical analyses, the shipping and textile printing industries were considered the significant contributors to the identified organic compounds. Considering the principles of the priority substances and the current status of the substances, two traditional pollutants and ten emerging organic compounds were recognized as the priority organic compounds for the Taipu River. Conclusively, this study established a workflow for NTS analysis of sediment samples and demonstrated the necessity of NTS analysis to evaluate the impact of terrestrial emissions of organic compounds on the aquatic environment.

Comparative study of synthesis methods and pH-dependent adsorption of methylene blue dye on UiO-66 and NH2-UiO-66

Metal-organic frameworks (MOFs) are highly promising adsorbents with notable properties such as elevated adsorption capacities and versatile surface design capabilities. This study introduces two distinct synthesis methods, one lasting 1 h and the other 24 h, for UiO-66 and NH2-UiO-66. While both methods yield structures with comparable crystallinity and morphology, the adsorption performance of the cationic methylene blue dye varies at different pH levels. Despite the 24 h synthesis time being optimal for maximum adsorption in both MOFs, the relative difference in NH2-UiO-66 adsorption percentage at different times suggests reduced dependency on synthesis time for this property. Notably, NH2-UiO-66 exhibits consistent and effective performance across three pH levels, warranting further investigation into its adsorption kinetics and isotherm. The achievement of high adsorption efficiency coupled with a significantly reduced synthesis time underscores the importance of developing simplified synthetic methods, essential for enhancing the practical applicability of MOFs in diverse applications.

Emerging pollutants in textile wastewater: an ecotoxicological assessment focusing on surfactants

Water and several chemicals, including dyestuffs, surfactants, acids, and salts, are required during textile dyeing processes. Surfactants are harmful to the aquatic environment and induce several negative biological effects in exposed biota. In this context, the present study aimed to assess acute effects of five surfactants, comprising anionic and nonionic classes, and other auxiliary products used in fiber dyeing processes to aquatic organisms Vibrio fischeri (bacteria) and Daphnia similis (cladocerans). The toxicities of binary surfactant mixtures containing the anionic surfactant dodecylbenzene sulfonate + nonionic fatty alcohol ethoxylate and dodecylbenzene sulfonate + nonionic alkylene oxide were also evaluated. Nonionic surfactants were more toxic than anionic compounds for both organisms. Acute nonionic toxicity ranged from 1.3 mg/L (fatty alcohol ethoxylate surfactant) to 2.6 mg/L (ethoxylate surfactant) for V. fischeri and from 1.9 mg/L (alkylene oxide surfactant) to 12.5 mg/L (alkyl aryl ethoxylated and aromatic sulfonate surfactant) for D. similis, while the anionic dodecylbenzene sulfonate EC50s were determined as 66.2 mg/L and 19.7 mg/L, respectively. Both mixtures were very toxic for the exposed organisms: the EC50 average in the anionic + fatty alcohol ethoxylate mixture was of 1.0 mg/L ± 0.11 for V. fischeri and 4.09 mg/L ± 0.69 for D. similis. While the anionic + alkylene oxide mixture, EC50 of 3.34 mg/L for D. similis and 3.60 mg/L for V. fischeri. These toxicity data suggested that the concentration addition was the best model to explain the action that is more likely to occur for mixture for the dodecylbenzene sulfonate and alkylene oxide mixtures in both organisms. Our findings also suggest that textile wastewater surfactants may interact and produce different responses in aquatic organisms, such as synergism and antagonism. Ecotoxicological assays provide relevant information concerning hazardous pollutants, which may then be adequately treated and suitably managed to reduce toxic loads, associated to suitable management plans.

In-situ synthesis of ZIF-8 on magnetic pineapple leaf biochar as an efficient and reusable adsorbent for methylene blue removal from wastewater

The presence of organic dyes in aquatic systems poses a significant threat to ecosystems and human well-being. Due to recycling challenges, traditional commercial activated carbon is not cost-effective. To address this, an imidazolate acid zeolite framework-8 (ZIF-8)-modified magnetic adsorbent (ZMPLB-800) was synthesized through the in-situ formation of ZIF-8 and subsequent carbonization at 800 °C, using magnetic pineapple leaf biochar (MPLB) as a carrier. The porous structure of ZMPLB-800 facilitates the rapid passage of dye molecules, enhancing adsorption performance. ZMPLB-800 exhibited remarkable adsorption capacity for methylene blue (MB) across a pH range of 3-13, with a maximum adsorption capacity of 455.98 mg g-1. Adsorption kinetics and thermodynamics followed the pseudo-second-order kinetic model and Langmuir isotherm model. Mechanisms of MB adsorption included pore filling, hydrogen bonding, electrostatic interactions, π-π interactions, and complexation through surface functional groups. Additionally, ZMPLB-800 demonstrated excellent regeneration performance, recording a removal efficiency exceeding 87% even after five adsorption/desorption cycles. This study provides a novel strategy for treating dye wastewater with MOF composites, laying the foundation for waste biomass utilization.

Applications of hollow nanostructures in water treatment considering organic, inorganic, and bacterial pollutants

One of the major issues of modern society is water contamination with different organic, inorganic, and contaminants bacteria. Finding cost-effective and efficient materials and methods for water treatment and environment remediation is among the scientists' most important considerations. Hollow-structured nanomaterials, including hollow fiber membranes, hollow spheres, hollow nanoboxes, etc., have shown an exciting capability for wastewater refinement approaches, including membrane technology, adsorption, and photocatalytic procedure due to their extremely high specific surface area, high porosity, unique morphology, and low density. Diverse hollow nanostructures could potentially eliminate organic contaminants, including dyes, antibiotics, oil/water emulsions, pesticides, and other phenolic compounds, inorganic pollutants, such as heavy metal ions, salts, phosphate, bromate, and other ions, and bacteria contaminations. Here, a comprehensive overview of hollow nanostructures' fabrication and modification, water contaminant classification, and recent studies in the water treatment field using hollow-structured nanomaterials with a comparative attitude have been provided, indicating the privilege abd detriments of this class of nanomaterials. Eventually, the future outlook of employing hollow nanomaterials in water refinery systems and the upcoming challenges arising in scaling up are also propounded.

Adsorption of azo dye by biomass and immobilized Yarrowia lipolytica; equilibrium, kinetic and thermodynamic studies

One of the major environmental problems we have today is dye pollution, primarily caused by the textile industry. This pollution has detrimental effects on aquatic life, soil fertility, and human health. Many microbial biosorbents have been documented in the literature for the removal of a wide range of azo dyes commonly employed in the textile industry. However, Yarrowia lipolytica NBRC1658 is firstly used as both free and immobilized sorbents for the removal of Reactive yellow 18 (RY18), acid red 18 (AR18) and basic blue 41 (BB41) in this study. The effect of experimental conditions such as pH, biosorbent quantity, dye concentration, contact time, and temperature on dye removal capacity are examined. The research findings demonstrate that the adsorption capacity is higher in biomass compared to immobilized cells. The highest adsorption capacities are observed at pH 2 for RY18 and AR18, while pH 9 is optimal for BB41. Increasing the adsorbent dosage and initial concentration significantly improves the adsorption capacity. The Langmuir model best describes the adsorption process, indicating that the dye attaches to the biosorbent in a single layer, with a uniform biosorbent surface. The removal of the dye occurs through a chemical process on the biosorbent surface, as evidenced by the pseudo-second-order kinetic model. According to thermodynamic analysis, higher temperatures promote greater adsorption of dyes. Our study shows the effectiveness of Yarrowia lipolyica NBRC1658 as a biosorbent in the removal of a wide range of industrial dyes.

Engineering Site 228 of Streptomyces coelicolor Laccase for Optimizing Catalytic Activity

Malachite green (MG) poses a formidable threat to ecosystems and human health. Laccase emerges as a promising candidate for MG degradation, prompting an investigation into the catalytic activity modulation of a small laccase (SLAC) from Streptomyces coelicolor, with a focus on amino acid position 228. Through saturation mutagenesis, five mutants with a 50% increase in the specific activity were generated. Characterization revealed notable properties, Km of E228F was 8.8% of the wild type (WT), and E288T exhibited a 133% kcat compared to WT. Structural analyses indicated improved hydrophobicity and electrostatic potential on the mutants' surfaces, with the stable E228F-ABTS complex exhibiting reduced flexibility, possibly contributing to the observed decrease in turnover rate. Mutants demonstrated enhanced MG decolorization, particularly E228G. Site 228 acts as a crucial functional control switch, suggesting its potential role in SLAC engineering. This study provides insights into laccase modulation and offers promising avenues for enzymatic bioremediation applications.

Enhanced mitigation of acidic and basic dyes by ZnO based nano-photocatalysis: current applications and future perspectives

Dye wastewater possess immense toxicity with carcinogenic properties and they persist in environment owing to their stability and resistance to chemical and photochemical changes. The bio degradability of dye-contaminated wastewater is low due to its complex molecular structure. Nano-photocatalysts based on zinc oxide are reported as one of the effective metal oxides for dye remediation due to their photostability, enhanced UV and visible absorption capabilities in an affordable manner. An electron-hole pair forms when electrons in the valence band of ZnO nano-photocatalyst transfer into the conduction band by absorbing UV light. The review article presents a detailed review on ZnO applications for treating acidic and basic dyes along with the dye degradation performance based on operating conditions and photocatalytic kinetic models. Several acidic and basic dyes have been shown to degrade efficiently using ZnO and its nanocomposites. Higher removal percentages for crystal violet was reported at pH 12 by ZnO/Graphene oxide catalyst under 400 nm UV light, whereas acidic dye Rhodamine B at a pH of 5.8 was degraded to 100% by pristine ZnO. The mechanism of action of ZnO nanocatalysts in degrading the dye contamination are reported and the research gaps to make these agents in environmental remediation on real time operations are discussed.

Powdered silk: A promising biopolymer for the treatment of dye contaminated water

Discharge of textile dye effluents into water bodies is creating stress to aquatic life and contaminating water resources. In this study, a new biopolymer adsorbent silk fibroin (SF) was prepared from Bombyx mori silk fibroin (SF) and used for removal of Solochrome Black-T (SB-T) from water. This innovative adsorbent exhibits an exceptional adsorption capacity of 20.08 mg/g, achieving a removal efficiency of approximately 98.6 % within 60 min. Notably, the powdered SF adsorbent demonstrates rapid kinetics, surpassing the performance of previously reported similar adsorbents in adsorption capacity and reaction speed. The molecular weight and particle diameter of the material were observed to be > 1.243 kDa and 3 μm, respectively. The experimental investigations were performed on different parameters, viz., adsorbent dosage, contact time, repeatability, and desorption-adsorption study. The experimental data well fit for the Langmuir model (R2 = 0.937, qmax = 20.08 mg/g) and the pseudo-second-order kinetics (R2 = 0.921 and qe = 1.496 mg/g). Compared to the adsorbents reported in the literature, the newly prepared SF showed high adsorption capacity and faster kinetics to address real-life situations. The novelty of this work extends beyond its remarkable adsorption capabilities. The SF adsorbent offers a cost-effective, sustainable solution and regenerable adsorption material with minimal negative environmental impacts. This regenerability, with its versatility and broad applicability, positions powdered SF fibroin as a transformative technology in water treatment and environmental protection.

Microorganism-mediated bioremediation of dyes from contaminated soil: Mechanisms, recent advances, and future perspectives

Many methods have been proposed for the remediation of dye-contaminated soils, a widespread form of environment pollution. Bioremediation, it is hoped, can combine ecological benefits with efficiency of dye decontamination. We review the types and sources of dye contaminants; their possible effects on plant, animal, and human health; and emerging strategies for microbial bioremediation. Challenges, limitations, recommendations for future research, and prospects for large-scale commercialization of microbial bioremediation are discussed.

Comparison of Dye Adsorption of Chitosan and Polyethylenimine Modified Bentonite Clays: Optimization, Isotherm, and Kinetic Studies

The aim of this study was to compare the effect of modifying calcium bentonite (Bent-Ca) clay with two cationic polymers, chitosan (Chi) and polyethylenimine (PEI), on the removal of remazol black B (RB-B) dye from an aqueous solution. The samples were characterized by using scanning electron microscopy, X-ray diffraction, and Fourier-transform infrared spectroscopy. The fractional factorial design of 2(6-1) was applied to investigate the effects of pH, temperature, amount of adsorbent, initial dye concentration, contact time, and shaking rate on the adsorption process. To further optimize RB-B removal from an aqueous solution, a Box-Behnken design with three factors and a response surface methodology was used. The optimum conditions were a pH of 3.77, a temperature of 40.45 °C, and an initial RB-B concentration of 77.27 mg L-1 for Bent-Ca-Chi, whereas for Bent-Ca-PEI, the optimum conditions were a pH of 5.53, a temperature of 41.06 °C, and an initial dye concentration of 238.89 mg L-1. To understand the adsorption behavior, the Langmuir and Freundlich isotherms were fitted to the experimental data. It was found that the Langmuir isotherm model matched well with the dye adsorption by Bent-Ca-Chi and Bent-Ca-PEI. The kinetics study was performed using three kinetic models: pseudo-first-order, pseudo-second-order, and intraparticle diffusion models. Among these models, the RB-B dye kinetics were best represented by the pseudo-second-order model equation for the adsorbents.

Highly Efficient Biosorption of Cationic Dyes via Biopolymeric Adsorbent-Material-Based Pectin Extract Polysaccharide and Carrageenan Grafted to Cellulosic Nonwoven Textile

Water scarcity and contamination have emerged as critical global challenges, requiring the development of effective and sustainable solutions for the treatment of contaminated water. Recently, functionalized polymer biomaterials have garnered significant interest because of their potential for a wide range of water treatment applications. Accordingly, this paper highlights the design of a new adsorbent material based on a cellulosic nonwoven textile grafted with two extracted biopolymers. The layer-by-layer grafting technique was used for the polyelectrolyte multi-layer (PEM) biosorbent production. Firstly, we extracted a Suaeda fruticosa polysaccharide (SFP) and confirmed its pectin-like polysaccharide structure via SEC, NMR spectroscopy, and chemical composition analyses. Afterward, the grafting was designed via an alternating multi-deposition of layers of SFP polymer and carrageenan crosslinked with 1,2,3,4-butanetetracarboxylic acid (BTCA). FT-IR and SEM were used to characterize the chemical and morphological characteristics of the designed material. Chemical grafting via polyesterification reactions of the PEM biosorbent was confirmed through FT-IR analysis. SEM revealed the total filling of material microspaces with layers of grafted biopolymers and a rougher surface morphology. The assessment of the swelling behavior revealed a significant increase in the hydrophilicity of the produced adsorbent system, a required property for efficient sorption potential. The evaluation of the adsorption capabilities using the methylene blue (MB) as cationic dye was conducted in various experimental settings, changing factors such as the pH, time, temperature, and initial concentration of dye. For the untreated and grafted materials, the greatest adsorbed amounts of MB were 130.6 mg/g and 802.6 mg/g, respectively (pH = 4, T = 22 C, duration = 120 min, and dye concentration = 600 mg/L). The high adsorption performance, compared to other reported materials, was due to the presence of a large number of hydroxyl, sulfonate, and carboxylic functional groups in the biosorbent polymeric system. The adsorption process fitted well with the pseudo-first-order kinetic model and Langmuir/Temkin adsorption isotherms. This newly developed multi-layered biosorbent shows promise as an excellent adsorption resultant and cheap-cost/easy preparation alternative for treating industrial wastewater.

Antibacterial and photocatalytic potential of bioactive compounds extracted from freshwater microalgae species (Spirogyra and Ocillatoria): A comparative analysis

Water pollution by pathogenic bacteria and organic dyes poses potential health hazards for human and aquatic life. This study aims to explore the potential of bioactive compounds extracted from two microalgae species (Spirogyra and Ocillatoria) for water pollution control. The optimization of the extraction process for bioactive compounds resulted in the highest yield at 25 min for Spirogyra and 30 min for Ocillatotia species. Further, the extracted bioactive compounds were analyzed using Fourier transform infrared spectroscopy (FTIR) and gas chromatography-mass spectroscopy (GC-MS). The bioactive compounds exhibited significant antibacterial activity against gram-positive and gram-negative bacteria. Notably, Spirogyra species exhibited a higher zone of inhibition (19.5-20.7 mm) than Ocillatoria species (17.0-18.0 mm) against both gram-positive and gram-negative bacterial strains. Furthermore, the photocatalytic potential of these bioactive compounds was examined by assessing the photodegradation of methylene blue (MB) and crystal violet (CV) dyes under different light sources. The findings revealed that Spirogyra species exhibited better photocatalytic activity than Ocillatoria species for MB and CV. For MB, 89.75 %, 77.82 % and 63.54 % were photodegraded when exposed to UV light, sunlight and visible light using Spirogyra extract, compared to 84.90 %, 74.70 % and 58.30 % by Ocillatoria extract. Regarding CV, Spirogyra extract achieved photodegradation efficiency of 88.94 %, 76.59 % and 64.50 % under UV light, sunlight and visible light, higher than 83.60 %, 73.60 % and 57.70 % by Ocillatoria extract. Both Spirogyra and Ocillatoria species demonstrated the best performance for dye photodegradation under UV irradiation, demonstrating great potential for nature-based water treatment.

Intelligent and active biodegradable biopolymeric films containing carotenoids

There is growing interest in the use of natural bioactive compounds for the development of new bio-based materials for intelligent and active food packaging applications. Several beneficial effects have been associated with the antioxidant and antimicrobial potentials of carotenoid compounds. In addition, carotenoids are sensitive to pH changes and oxidation reactions, which make them useful bioindicators of food deterioration. This review summarizes the current research on the application of carotenoids as novel intelligent and active biodegradable food packaging materials. Carotenoids recovered from food processing by-products can be used in the development of active food packaging materials due to their antioxidant properties. They help maintain the stability of lipid-rich foods, such as vegetable oils. Additionally, when incorporated into films, carotenoids can monitor food oxidation, providing intelligent functionalities.

Smart optical sensing of multiple antibiotic residues from wastewater effluents with ensured specificity using SERS assisted with multivariate analysis

Surface-enhanced Raman spectroscopy offers great potential for rapid and highly sensitive detection of pharmaceuticals from environmental sources. Herein, we investigated the feasibility of label-free sensing of antibiotic residues from wastewater effluents with high specificity by combining with multivariate analysis. Highly ordered silver nanoarrays with ∼34 nm roughness have been fabricated using a cost-effective electroless deposition technique. As-fabricated Ag arrays showed superior LSPR effects with an enhancement factor of 8 × 107. Excellent reproducibility has also been noticed with RSD values within 11%, whilst the sensor showed good stability and reusability characteristics for being used as a low-cost and reusable sensor. SERS studies demonstrated that antibiotics-spiked wastewater effluents can be detected with high efficiency in a label-free method. The molecular fingerprint bands of antibiotics such as sulfamethoxazole, sulfadiazine, and ciprofloxacin were well analyzed in effluent, tap, and deionized water. It has been found that antibiotics can be detected near picomolar levels; meanwhile, liquid chromatography-mass spectrometry (LC-MS) exhibited a detection limit within nanomolar concentrations only. Furthermore, the specificity of SERS sensing has been further analyzed using a multivariate analysis method, principal component analysis followed by linear discriminant analysis (PCA-LDA); which showed prominent discrimination to distinguish each antibiotic residue from wastewater effluents. The current study presented the potential of Ag nanoarray sensors for rapid, highly specific, and cost-effective analysis of pharmaceutical products for environmental remediation applications.

Development of the Sb4O5Cl2@NbSe2 Composite: The Impact of 2H-NbSe2 Nanoparticles on Sb4O5Cl2 and Their Application for the Removal of Cr(VI)/Fe(III) and Methyl Orange from Wastewater

A potential adsorbent, Sb4O5Cl2@NbSe2 composite, was generated from the Sb4O5Cl2 photocatalyst and 5 wt % layered 2H-NbSe2 nanoparticles for the highly effective removal of Cr(VI) and Fe(III) ions and methyl orange (MO) from aqueous solution, and a comparison was drawn against the precursors. Sb4O5Cl2 crystallites and NbSe2 nanoparticles were synthesized hydrothermally, and the composite was prepared by the incipient wetness impregnation technique. The crystal structure of Sb4O5Cl2 was determined by single-crystal X-ray diffraction (SCXRD) data. Powder X-ray diffraction (PXRD) study revealed the 2H phase of NbSe2 nanoparticles. Field emission scanning electron microscopy (FESEM) analysis confirmed the formation of the spherical-shaped NbSe2 nanoparticles from rod-shaped bulk 2H-NbSe2. Morphological changes from the hexagonal to irregular prismatic shape were found upon the formation of the Sb4O5Cl2@NbSe2 composite compared to pure Sb4O5Cl2. Negative ζ-potential values indicated that electrostatic interactions were the predominant factor for the adsorption process. Sb4O5Cl2@NbSe2 provided removal efficiencies of 99% for MO in 6 h, 96.52% for Cr(VI) within 2.5 h, and 92.43% for Fe(III) within 4 h of 10 mg/L initial concentration. The maximum adsorption capacities of the composite for MO, Fe(III), and Cr(VI) were found to be 66.56, 131.48, and 122.30 mg/g, respectively, as calculated using the Langmuir isotherm equation.

Microbial communities drive flux of acid orange 7 and crystal violet dyes in water-sediment system

Unchecked dye effluent discharge poses escalating environmental and economic concerns, especially in developing nations. While dyes are well-recognized water pollutants, the mechanisms of their environmental spread are least understood. Therefore, the present study examines the partitioning of Acid Orange 7 (AO7) and Crystal Violet (CV) dyes using water-sediment microcosms and reports that native microbes significantly affect AO7 decolorization and transfer. Both dyes transition from infused to pristine matrices, reaching equilibrium in a fortnight. While microbes influence CV partitioning, their role in decolorization is minimal, emphasizing their varied impact on the environmental fate of dyes. Metagenomic analyses reveal contrasting microbial composition between control and AO7-infused samples. Control water samples displayed a dominance of Proteobacteria (62%), Firmicutes (24%), and Bacteroidetes (9%). However, AO7 exposure led to Proteobacteria reducing to 57% and Bacteroidetes to 3%, with Firmicutes increasing to 34%. Sediment samples, primarily comprising Firmicutes (47%) and Proteobacteria (39%), shifted post-AO7 exposure: Proteobacteria increased to 53%, and Firmicutes dropped to 38%. At the genus level, water samples dominated by Niveispirillum (34%) declined after AO7 exposure, while Bacillus and Pseudomonas increased. Notably, Serratia and Sphingomonas, known for azo dye degradation, rose post-exposure, hinting at their role in AO7 decolorization. Conversely, sediment samples showed a decrease in the growth of Bacillus and an increase in that of Pseudomonas and Serratia. These findings emphasize the significant role of microbial communities in determining the environmental fate of dyes, providing insights on its environmental implications and management.

Recent advances in visible light-activated photocatalysts for degradation of dyes: A comprehensive review

The rapid development in industrialization and urbanization coupled with an ever-increasing world population has caused a tremendous increase in contamination of water resources globally. Synthetic dyes have emerged as a major contributor to environmental pollution due to their release in large quantities into the environment, especially owing to their high demand in textile, cosmetics, clothing, food, paper, rubber, printing, and plastic industries. Photocatalytic treatment technology has gained immense research attention for dye contaminated wastewater treatment due to its environment-friendliness, ability to completely degrade dye molecules using light irradiation, high efficiency, and no generation of secondary waste. Photocatalytic technology is evolving rapidly, and the foremost goal is to synthesize highly efficient photocatalysts with solar energy harvesting abilities. The current review provides a comprehensive overview of the most recent advances in highly efficient visible light-activated photocatalysts for dye degradation, including methods of synthesis, strategies for improving photocatalytic activity, regeneration and their performance in real industrial effluent. The influence of various operational parameters on photocatalytic activity are critically evaluated in this article. Finally, this review briefly discusses the current challenges and prospects of visible-light driven photocatalysts. This review serves as a convenient and comprehensive resource for comparing and studying the fundamentals and recent advancements in visible light photocatalysts and will facilitate further research in this direction.

Biochar obtained from alkaline earth metal-treated mushroom residue: Thermal behavior and methyl orange adsorption capability

To achieve the resource utilization of edible fungi residue and obtain efficient adsorbents for treating dyeing wastewater, biochars were prepared from mushroom residue (MR) with the introduction of alkaline-earth metals (AEMs) and used for methyl orange (MO) wastewater treatment. The thermal behavior of the AEM-treated MR was analyzed using thermogravimetric analysis. The physicochemical properties of the biochars obtained from AEM-treated MR (MRCs) were characterized using Fourier transform infrared spectroscopy, laser particle size analyzer, N2 adsorption/desorption, and scanning electron microscopy. The adsorption performance of MRCs on MO was also investigated. The involvement of AEMs was found to obviously move the main pyrolysis zone of MR to a low temperature region and reduce the temperature corresponding to the maximum weight loss rate and activation energy, which is highly dependent on the concentration of AEMs, the anion and cationic species of the AEMs. Moreover, the addition of AEMs resulted in a decrease in oxygen-containing functional groups (-OH, CO, or C-O), a weakening of surface negative charges, an enhancement in aromatic functional groups, and an increase in specific surface area of the MRCs. The adsorption performance of MO on MRCs was significantly improved with the introduction of AEMs as well. Among them, MR pre-treated with 5 mmol/g MgCl2 (MR-MgCl2-5) shows the lowest temperature corresponding to the maximum weight loss rate and the lowest activation energy of 278.52 °C and 4.28 kJ/mol, respectively. The biochar prepared from MR-MgCl2-5 under 400 °C (MR-MgCl2-5-400C) has the weakest surface negative charge and the highest adsorption capacity for MO. The adsorption isotherms, adsorption kinetics, and thermodynamic analysis results showed that the adsorption of MO on MR-MgCl2-5-400C was a spontaneous, chemically dominant monolayer adsorption, with a theoretical maximum adsorption capacity of 81.30 mg/g. This study suggests that AEMs treatment, especially with 5 mmol/g MgCl2, can readily transform edible fungi residue into a low-cost, high-efficient dyeing wastewater adsorbent.

Adsorption of contaminants by nanomaterials synthesized by green and conventional routes: a critical review

Nanomaterials, due to their large surface area and selectivity, have stood out as an alternative for the adsorption of contaminants from water and effluents. Synthesized from green or traditional protocols, the main advantages and disadvantages of green nanomaterials are the elimination of the use of toxic chemicals and difficulty of reproducing the preparation of nanomaterials, respectively, while traditional nanomaterials have the main advantage of being able to prepare nanomaterials with well-defined morphological properties and the disadvantage of using potentially toxic chemicals. Thus, based on the particularities of green and conventional nanomaterials, this review aims to fill a gap in the literature on the comparison of the synthesis, morphology, and application of these nanomaterials in the adsorption of contaminants in water. Focusing on the adsorption of heavy metals, pesticides, pharmaceuticals, dyes, polyaromatic hydrocarbons, and phenol derivatives in water, for the first time, a review article explored and compared how chemical and morphological changes in nanoadsorbents synthesized by green and conventional protocols affect performance in the adsorption of contaminants in water. Despite advances in the area, there is still a lack of review articles on the topic.

Optimized Polymeric Membranes for Water Treatment: Fabrication, Morphology, and Performance

Conventional polymers, endowed with specific functionalities, are extensively utilized for filtering and extracting a diverse set of chemicals, notably metals, from solutions. The main structure of a polymer is an integral part for designing an efficient separating system. However, its chemical functionality further contributes to the selectivity, fabrication process, and resulting product morphology. One example would be a membrane that can be employed to selectively remove a targeted metal ion or chemical from a solution, leaving behind the useful components of the solution. Such membranes or products are highly sought after for purifying polluted water contaminated with toxic and heavy metals. An efficient water-purifying membrane must fulfill several requirements, including a specific morphology attained by the material with a specific chemical functionality and facile fabrication for integration into a purifying module Therefore, the selection of an appropriate polymer and its functionalization become crucial and determining steps. This review highlights the attempts made in functionalizing various polymers (including natural ones) or copolymers with chemical groups decisive for membranes to act as water purifiers. Among these recently developed membrane systems, some of the materials incorporating other macromolecules, e.g., MOFs, COFs, and graphene, have displayed their competence for water treatment. Furthermore, it also summarizes the self-assembly and resulting morphology of the membrane materials as critical for driving the purification mechanism. This comprehensive overview aims to provide readers with a concise and conclusive understanding of these materials for water purification, as well as elucidating further perspectives and challenges.

Visible Light Motivated the Photocatalytic Degradation of P-Nitrophenol by Ca2+-Doped AgInS2

4-Nitrophenol (4-NP) is considered a priority organic pollutant with high toxicity. Many authors have been committed to developing efficient, green, and environmentally friendly technological processes to treat wastewater containing 4-NP. Here, we investigated how the addition of Ca2+ affects the catalytic degradation of 4-NP with AgInS2 when exposed to light. We synthesized AgInS2 (AIS) and Ca2+-doped AgInS2 (Ca-AIS) with varying amounts of Ca2+ using a low-temperature liquid phase method. The SEM, XRD, XPS, HRTEM, BET, PL, and UV-Vis DRS characteristics were employed to analyze the structure, morphology, and optical properties of the materials. The effects of different amounts of Ca2+ on the photocatalytic degradation of 4-NP were investigated. Under visible light illumination for a duration of 120 min, a degradation rate of 63.2% for 4-Nitrophenol (4-NP) was achieved. The results showed that doping with an appropriate amount of Ca2+ could improve the visible light catalytic activity of AIS. This work provides an idea for finding suitable cheap alkaline earth metal doping agents to replace precious metals for the improvement of photocatalytic activities.

Synthesis and characterization of titanium dioxide nanoparticles from Bacillus subtilis MTCC 8322 and its application for the removal of methylene blue and orange G dyes under UV light and visible light

Over the last decade there has been a huge increase in the green synthesis of nanoparticles. Moreover, there is a continuous increase in harnessing the potential of microorganisms for the development of efficient and biocompatible nanoparticles around the globe. In the present research work, investigators have synthesized TiO2 NPs by harnessing the potential of Bacillus subtilis MTCC 8322 (Gram-positive) bacteria. The formation and confirmation of the TiO2 NPs synthesized by bacteria were carried out by using UV-Vis spectroscopy, Fourier transforms infrared (FT-IR), X-ray diffraction (XRD), scanning electron microscope (SEM), and energy dispersive X-ray spectroscopy (EDX/EDS). The size of the synthesized TiO2 NPs was 80-120 nm which was spherical to irregular in shape as revealed by SEM. FTIR showed the characteristic bands of Ti-O in the range of 400-550 cm-1 and 924 cm-1 while the band at 2930 cm-1 confirmed the association of bacterial biomolecules with the synthesized TiO2 NPs. XRD showed two major peaks; 27.5° (rutile phase) and 45.6° (anatase phase) for the synthesized TiO2 NPs. Finally, the potential of the synthesized TiO2 NPs was assessed as an antibacterial agent and photocatalyst. The remediation of Methylene blue (MB) and Orange G (OG) dyes was carried out under UV- light and visible light for a contact time of 150-240 min respectively. The removal efficiency for 100 ppm MB dye was 25.75% and for OG dye was 72.24% under UV light, while in visible light, the maximum removal percentage for MB and OG dye was 98.85% and 80.43% respectively at 90 min. Moreover, a kinetic study and adsorption isotherm study were carried out for the removal of both dyes, where the pseudo-first-order for MB dye is 263.269 and 475554.176 mg/g for OG dye. The pseudo-second-order kinetics for MB and OG dye were 188.679 and 1666.667 mg/g respectively. In addition to this, the antibacterial activity of TiO2 NPs was assessed against Bacillus subtilis MTCC 8322 (Gram-positive) and Escherichia coli MTCC 8933 (Gram-negative) where the maximum zone of inhibition in Bacillus subtilis MTCC 8322 was about 12 mm, and for E. coli 16 mm.