Extracellular biopolymers recovered as raw biomaterials from waste granular sludge and potential applications: A critical review

A novel strategy for waste activated sludge treatment: Recovery of structural extracellular polymeric substances and fermentative production of volatile fatty acids

Structural extracellular polymeric substances (SEPS) as valuable biopolymers, can be extracted from waste activated sludge (WAS). However, the extraction yield is typically low, and detailed information on SEPS characterizations, as well as proper treatment of the sludge after SEPS extraction, remains limited. This study aimed to optimize the conditions of heating-Na2CO3 extraction process to increase the yield of SEPS extracted from WAS. Subsequently, SEPS were characterized, and, for the first time, insights into their protein composition were uncovered by using proteomics. A maximum SEPS yield of 209 mg g-1 volatile solid (VS) was obtained under optimal conditions: temperature of 90 °C, heating time of 60 min, Na+ dosage of 8.0 mmol/g VS, and pH required to precipitation of 4.0, which was comparable to that from the aerobic granular sludge reported in literature. Proteomics analysis unveiled that the proteins in SEPS primarily originated from microorganisms involved in nitrogen fixation and organic matter degradation, including their intracellular and membrane-associated regions. These proteins exhibited various catalytic activities and played crucial roles in aggregation processes. Besides, the process of SEPS extraction significantly enhanced volatile fatty acid (VFA) production during the anaerobic fermentation of residual WAS after SEPS extraction. A maximum VFA yield of 420 ± 14 mg COD/g VSadded was observed in anaerobic fermentation of 10 d, which was 77.2 ± 0.1 % higher than that from raw sludge. Mechanism analysis revealed that SEPS extraction not only improved WAS disintegration and solubilization but also reduced the relative activity of methanogens during anaerobic fermentation. Moreover, SEPS extraction shifted the microbial population during anaerobic fermentation in the direction towards hydrolysis and acidification such as Fermentimonas sp. and Soehngenia sp. This study proposed a novel strategy based on SEPS extraction and VFA production for sludge treatment, offering potential benefits for resource recovery and improved process efficiency.

Cationic polymer-mediated interbacterial aggregation: A novel approach for rapid aerobic granules development

This study introduces a novel approach to aerobic granular sludge technology that minimizes the start-up time and guarantees the formation of stable granules. This is achieved by seeding the reactor with a cationic polymer without using inoculated sludge. Three cationic polymers (Hydrofloc C4400SA, C8896, and polyelectrolyte emulsion) were tested to determine the most appropriate polymer for aerobic granular sludge (AGS) startup based on the optimal dose and formation of aerobic granules. Hydrofloc cationic polymer C4400SA has excellent granule-forming properties in the AGS reactor compared to their counterparts. The formation of granules was boosted by adding 15 ppm of polymer, resulting in densely packed aerobic granules after 10 days. This improvement can be due to the more cationic properties of hydrofloc, which play a key role in bridging between cells and particles because the cationic charges of hydrofloc attract negatively charged bacteria in wastewater, thereby promoting aggregation and the formation of initial flocs. These flocs serve as the foundation for the development of granules. After 80 days of operation, 40-50% of particles with an average size range from 0.6 to 0.9 mm were observed. The AGS SBR operation was closely monitored and showed consistent efficiency in removing solids, where TP, TN, NH+4 -N, and the total soluble COD were removed at average efficiencies of 62%, 73%, 97%, 93%, and 79% respectively, during steady-state cycles conducted at room temperature. Overall, this study highlights the potential of hydrofloc cationic polymer C4400SA to enhance the performance and resilience of AGS in wastewater treatment applications.

Effect of cations on aerobic granulation for sidestream treatment

Aerobic granular sludge (AGS) represents an aggregate of sludge formed through the self-immobilization of microorganisms under aerobic conditions. It is currently under scrutiny for its potential as a technology to reduce carbon emissions and promote sustainability. The practicality of AGS stems from its ability to encourage granule formation and enhance structural stability. In this study, a total of five cations (K+, Ca2+, Mg2+, Al3+, Fe3+) were introduced to facilitate stable structuring and the formation of granules for treating high-strength wastewater, such as side-stream treatment. As a result of the experiment, the loosely bound extracellular polymeric substances (LB-EPS) content in the cation-enhanced sludge witnessed a significant increase, leading to elevated total EPS content under all experimental conditions. Furthermore, the protein (PN)/polysaccharide (PS) ratio, a pivotal component of EPS influencing AGS's hydrophobicity and structural stability, exhibited a collective increase, with Mg2+ reaching the highest value of 1.7. The relationship between relative hydrophobicity and the PN/PS ratio was found to strongly impact sludge adhesion, with noteworthy results observed particularly for Mg2+, Al3+, and Fe3+. The viability of attached cells reached 96.8 %, the highest recorded in the case of Mg2+. In the context of treating high-strength wastewater, Mg2+ emerged as the optimal cation for accelerating AGS formation and enhancing structural stability.

Extracellular polymeric substances as paper coating biomaterials derived from anaerobic granular sludge

Recovering extracellular polymeric substances (EPS) from waste granular sludge offers a cost-effective and sustainable approach for transforming wastewater resources into industrially valuable products. Yet, the application potential of these EPS in real-world scenarios, particularly in paper manufacturing, remains underexplored. Here we show the feasibility of EPS-based biomaterials, derived from anaerobic granular sludges, as novel coating agents in paper production. We systematically characterised the rheological properties of various EPS-based suspensions. When applied as surface sizing agents, these EPS-based biomaterials formed a distinct, ultra-thin layer on paper, as evidenced by scanning electron microscopy. A comprehensive evaluation of water and oil penetration, along with barrier properties, revealed that EPS-enhanced coatings markedly diminished water absorption while significantly bolstering oil and grease resistance. Optimal performance was observed in EPS variants with elevated protein and hydrophobic contents, correlating with their superior rheological characteristics. The enhanced water-barrier and grease resistance of EPS-coated paper can be attributed to its non-porous, fine surface structure and the functional groups in EPS, particularly the high protein content and hydrophobic humic-like substances. This research marks the first demonstration of utilizing EPS from anaerobic granular sludge as paper-coating biomaterials, bridging a critical knowledge gap in the sustainable use of biopolymers in industrial applications.

Mechanistic insight into microbial interaction and metabolic pattern of anammox consortia on surface-modified biofilm carrier with extracellular polymeric substances

The extremely slow growth rate of anaerobic ammonia oxidation (anammox) bacteria limits full-scale application of anammox process worldwide. In this study, extracellular polymeric substances (EPS)-coated polypropylene (PP) carriers were prepared for biofilm formation. The biomass adhesion rate of EPS-PP carrier was 12 times that of PP carrier, and EPS-PP achieved significant enrichment of E. coli BY63. The 120-day continuous flow experiment showed that the EPS-PP carrier accelerated the formation of anammox biofilm, and the nitrogen removal efficiency increased by 10.5 %. In addition, the abundance of Candidatus Kuenenia in EPS-PP biofilm was 27.1%. Simultaneously, amino acids with high synthesis cost and the metabolites of glycerophospholipids related to biofilm formation on EPS-PP biofilm were significantly up-regulated. Therefore, EPS-PP carriers facilitated the rapid formation of anammox biofilm and promoted the metabolic activity of functional bacteria, which further contributed to the environmental and economic sustainability of anammox process.

Natural bioink of interpenetrating network hydrogels mimicking extracellular polymeric substances for microbial immobilization in water pollution control

Artificial biomanufacturing has been developed as a promising biotechnology for water pollution control. Effective bioimmobilization techniques are limited in application because of low productivity and the difficulty in achieving both mechanical strength and biocompatibility. Bioprinting technology, using biomaterials as bioink to enable the rapid on-demand production of bioactive structures, opens a new path for bioimmobilization. In this study, mimicking extracellular polysaccharide and protein of aerobic granular sludge (AGS), sodium alginate (SA) and silk fibroin methacryloyl (SilMA) were developed as the dual-component bioink with a suitable viscosity for bioprinting hydrogel. Interpenetrating network (IPN) hydrogel beads were manufactured using 1.5% (w/v) SA combined with 20% (w/v) SilMA through physical and covalent crosslinking, which exhibited excellent structural stability and bioactivity. The addition of SilMA provided a solution to the poor mechanical stability of SA-Ca hydrogels limited by Ca2+-Na+ ionic exchange. The unique structure of SilMA contributed to the reduction of hydrogel swelling as well as the prevention of SA loss. IPN hydrogels showed a swelling rate of less than 20% compared to the high swelling rate of more than 60% for SA hydrogels. On the other hand, SA controlled the hardening induced by excessive self-assembly of SilMA and improved mass transport in SilMA hydrogels. Compared to IPN hydrogels, SilMA hydrogels experienced a 15% volumetric shrinkage and exhibited a low water content of 92%. Sonication pretreatment of the dual-component bioink not only increased the intermolecular chain entanglement to form IPN, but also led to β-sheet content in SiMA reaching 46%-48%, which resulted in the formation of stable IPN hydrogels dominated entirely by physical crosslinking. Satisfactory proliferation and viability were achieved for the encapsulated bacteria in IPN hydrogels (μmax 1.49-2.18 d-1). Further, the IPN biohydrogels could maintain structural stability as well as achieve pollutant removal for treating synthetic wastewater with high Na+ concentration of 300 mg/L. The novel SA/SilMA hydrogel bioprinting strategy established in this study offers a new direction for bioimmobilization in water pollution control and other environmental applications.

Metabolomic reveals the responses of sludge properties and microbial communities to high nitrite stress in denitrifying phosphorus removal systems

Nitrite, as an electron acceptor, plays a good role in denitrifying phosphorus removal (DPR); however, high nitrite concentration has adverse affects on sludge performance. We investigated the precise mechanisms of responses of sludge to high nitrite stress, including surface characteristics, intracellular and extracellular components, microbial and metabolic responses. When the nitrite stress reached 90 mg/L, the sludge settling performance was improved, but the activated sludge was aging. FTIR and XPS analysis revealed a significant increase in the hydrophobicity of the sludge, resulting in improve settling performance. However, the intracellular carbon sources synthesis was inhibited. In addition, the components in the tightly bound extracellular polymeric substances (TB-EPS) of sludge were significantly reduced and indicated the disturb of metabolism. Notably, Exiguobacterium emerged as a new genus when face high nitrite stress that could maintaining survival in hostile environments. Moreover, metabolomic analysis demonstrated strong biological response to nitrite stress further supported above results that include the inhibited of carbohydrate and amino acid metabolism. More importantly, some lipids (PS, PA, LysoPA, LysoPC and LysoPE) were significantly upregulated that related enhanced membrane lipid remodeling. The comprehensive analyses provide novel insights into the high nitrite stress responses mechanisms in activated sludge systems.

Fractionation of Extracellular Polymeric Substances by Aqueous Three-Phase Partitioning Systems

Extracellular polymeric substances (EPS) are natural polymers secreted by microorganisms and represent a key chemical for the development of a range of circular economy applications. The production of EPS comes with notable challenges such as downstream processing. In this work, a three-phase partitioning (TPP) system was investigated as a fractionation technique for the separation of polysaccharides and proteins, both present in the EPS culture broth. The effect of the type of phase-forming compounds (alcohol, polymer, or ionic liquid, in combination with salt) and its concentration were evaluated and compared to the results previously obtained with model systems. The recyclability of phase-forming compounds used to form the fractionation platform was assessed by ultrafiltration. The best fractionation of EPS was achieved using a TPP system composed of 23 wt % ethanol and 25% K3C6H5O7 as 82% EPS-PS partitioned to the salt-rich/bottom phase, and 76% EPS-PN was recovered as an interfacial precipitate, which could be readily resolubilized in water. This represented an increase of 1.24 and 2.83-fold in the purity of EPS-PS and EPS-PN, respectively, in relation to the initial feed concentration. Finally, high recovery yields of phase-forming compounds (>99%) and fractionated EPS (>80%) were obtained using ultrafiltration/diafiltration (UF/DF) as the regeneration technique. The substantial fractionation yields, selectivity, and recyclability of the phase-forming compounds confirm the potential of TPP systems in combination with UF/DF as the separation method for real biopolymer mixtures. Key contributions of this study include the demonstration of the applicability of a readily scalable and cost-effective separation technique for the fractionation of EPS from real EPS-containing broths, while also the limitations of prescreening with model systems became clear through the observed deviating trends between model system studies and real broth studies.

Effects of enhanced biological phosphorus removal on rapid control of sludge bulking and fast formation of aerobic granular sludge

This study investigated the effects of enhanced biological phosphorus removal (EBPR) on rapid sludge bulking control and fast aerobic granular sludge (AGS) formation by adding 20 % of EBPR activated sludge to the bulking activated sludge (BAS) reactor. The results indicate that activating EBPR activity swiftly improved BAS settleability within 16 days, thus resolving sludge bulking issues. Subsequently, a settling time-based selection was employed, resulting in the BAS granulation within another 16 days. The rapid achievement of EBPR activity improved the BAS settleability and facilitated the formation of sludge aggregates, thereby expediting BAS granulation. Inhibition of filamentous bacteria and enrichment of slow-growing organisms contributed to both sludge bulking control and aerobic granulation. Furthermore, the increase in proteins/polysaccharides ratio facilitated the granulation process. Additionally, total nitrogen removal increased from 59.4 % to 71.7 % because of the mature AGS formation. This study provided an approach to simultaneously control sludge bulking and promote aerobic granulation.

Co-hydrothermal carbonization of pretreated sludge and polyethylene terephthalate for the preparation of low-nitrogen clean solid fuels

In this work, polyethylene terephthalate (PET) and sewage sludge (SS) were co-hydrothermally carbonized to produce low-nitrogen solid fuels. To minimize the effect of nitrogen, this work introduces a co-hydrothermal carbonization method involving alkali (A), ultrasonic cell disruptor (UCC), and sodium dodecyl sulfate (SDS) for both individual and combined pretreatment of SS and PET. Comparative analysis of the products shows that the combined pretreatment with sodium dodecyl sulfate (SDS) and alkali (A) effectively disrupts the SS cell structure, leading to the loosening of stable extracellular polymeric substances (EPS). This condition is conducive to the release and hydrolysis of proteins during hydrothermal carbonization. Moreover, under conditions where PET serves both as an acid producer and a carbon source, and through parameter optimization at a temperature of 240 °C, reaction time of 2 h, PET addition of 20 wt%, and water addition of 0.6 g cm-3, a high-quality, low-nitrogen clean solid fuel was produced (N: 0.51 wt%, C: 19.10 wt%).

Impact of food waste addition in energy efficient municipal wastewater treatment by aerobic granular sludge process

Recently, one of the main purposes of wastewater treatment plants is to achieve a neutral or positive energy balance while meeting the discharge criteria. Aerobic granular sludge (AGS) technology is a promising technology that has low energy and footprint requirements as well as high treatment performance. The effect of co-treatment of municipal wastewater and food waste (FW) on the treatment performance, granule morphology, and settling behavior of the granules was investigated in the study. A biochemical methane potential (BMP) test was also performed to assess the methane potential of mono- and co-digestion of the excess sludge from the AGS process. The addition of FW into wastewater enhanced the nutrient treatment efficiency in the AGS process. BMP of the excess sludge from the AGS process fed with the mixture of wastewater and FW (195 ± 17 mL CH4/g VS) was slightly higher than BMP of excess sludge from the AGS process fed with solely wastewater (173 ± 16 mL CH4/g VS). The highest methane yield was observed for co-digestion of excess sludge from the AGS process and FW, which was 312 ± 8 mL CH4/g VS. Integration of FW as a co-substrate in the AGS process would potentially enhance energy recovery and the quality of effluent in municipal wastewater treatment.

The water-soluble fraction of extracellular polymeric substances from a resource recovery demonstration plant: characterization and potential application as an adhesive

Currently, there is a growing interest in transforming wastewater treatment plants (WWTPs) into resource recovery plants. Microorganisms in aerobic granular sludge produce extracellular polymeric substances (EPS), which are considered sustainable resources to be extracted and can be used in diverse applications. Exploring applications in other high-value materials, such as adhesives, will not only enhance the valorization potential of the EPS but also promote resource recovery. This study aimed to characterize a water-soluble fraction extracted from the EPS collected at the demonstration plant in the Netherlands based on its chemical composition (amino acids, sugar, and fatty acids) and propose a proof-of-concept for its use as an adhesive. This fraction comprises a mixture of biomolecules, such as proteins (26.6 ± 0.3%), sugars (21.8 ± 0.2%), and fatty acids (0.9%). The water-soluble fraction exhibited shear strength reaching 36-51 kPa across a pH range of 2-10 without additional chemical treatment, suggesting a potential application as an adhesive. The findings from this study provide insights into the concept of resource recovery and the valorization of excess sludge at WWTPs.

Microbially driven Fe-N cycle: Intrinsic mechanisms, enhancement, and perspectives

The iron‑nitrogen (FeN) cycle driven by microbes has great potential for treating wastewater. Fe is a metal that is frequently present in the environment and one of the crucial trace elements needed by microbes. Due to its synergistic role in the microbial N removal process, Fe goes much beyond the essential nutritional needs of microorganisms. Investigating the mechanisms behind the linked Fe-N cycle driven by microbes is crucial. The Fe-N cycle is frequently connected with anaerobic ammonia oxidation (anammox), nitrification, denitrification, dissimilatory nitrate reduction to ammonium (DNRA), Feammox, and simultaneous nitrification denitrification (SND), etc. Although the main mechanisms of Fe-mediated biological N removal may vary depending on the valence state of the Fe, their similar transformation pathways may provide information on the study of certain element-microbial interactions. This review offers a thorough analysis of the facilitation effect and influence of Fe on the removal of nitrogenous pollutants in various biological N removal processes and summarizes the ideal Fe dosing. Additionally, the synergistic mechanisms of Fe and microbial synergistic N removal process are elaborated, covering four aspects: enzyme activity, electron transfer, microbial extracellular polymeric substances (EPS) secretion, and microbial community interactions. The methods to improve biological N removal based on the intrinsic mechanism were also discussed, with the aim of thoroughly understanding the biological mechanisms of Fe in the microbial N removal process and providing a reference and thinking for employing Fe to promote microbial N removal in practical applications.

Advances from conventional to biochar enhanced biotreatment of dyeing wastewater: A critical review

DW (Dyeing wastewater) contains a large amount of dye organic compounds. A considerable proportion of dye itself or its intermediate products generated during wastewater treatment process exhibits CMR (Carcinogenic/Mutagenic/Toxic to Reproduction) toxicity. Compared with physicochemical methods, biological treatment is advantageous in terms of operating costs and greenhouse gas emissions, and has become the indispensable mainstream technology for DW treatment. This article reviews the adsorption and degradation mechanisms of dye organic compounds in wastewater and analyzed different biological processes, ranging from traditional methods to processes enhanced by biochar (BC). For traditional biological processes, microbial characteristics and communities were discussed, as well as the removal efficiency of different bioreactors. BC has adsorption and redox electron mediated effects, and coupling with biological treatment can further enhance the process of biosorption and degradation. Although BC coupled biological treatment shows promising dye removal, further research is still needed to optimize the treatment process, especially in terms of technical and economic competitiveness.

Overlooked role in bacterial assembly of different-sized granules in same sequencing batch reactor: Insights into bacterial niche of nutrient removal

The unique ecosystem within different-sized granules affects microbial assembly, which is crucial for wastewater treatment performance. This study operated an aerobic granular sludge system to evaluate its performance in treating synthetic municipal wastewater. Subsequently, the microbial community within different-sized granules was characterized to investigate bacterial assembly, and elucidated their biological potential for nutrient removal. The nutrient removal efficiencies were as follows: 93.8 ± 2.8 % chemical oxygen demand, 65.4 ± 4.0 % total nitrogen, and 93.8 ± 6.8 % total phosphorus. The analysis of microbial assembly unveiled remarkable diversity among different-sized sludges, the genus relative abundance displayed 61.4 % positive and 33.0 % negative correlation with sludge size. The excellent potential for organic degradation, denitrification, and polyphosphate accumulation occurred in sludge sizes of > 0.75 mm, 0.20-0.50 mm, and < 0.20 mm, respectively. Functional annotation further confirmed the nutrient removal potential within different-sized sludges. This study provides valuable insights into the bacterial niche of different-sized sludges, which can enhance their practical application.

Valorization of sewage sludge for facile and green wood bio-adhesives production

A method is presented herein for the design of wood bio-adhesives using sewage sludge extracts (SSE). SSE was extracted from SS using deep eutectic solvents and processed with glycerol triglycidyl ether (GTE) to disrupt the secondary structure of proteins. An additive was also used to improve mechanical performance. The resulting bio-adhesive (SSE/GTE@TA) had a wet shear strength of 0.93 MPa, meeting the Chinese national standard GB/T 9846-2015 (≥0.7 MPa). However, the high polysaccharide content in SSE would weaken the mechanical properties of wood bio-adhesives. The key to improve bio-adhesive quality was the formation of a strong chemical bond via Maillard reaction as well as higher temperatures (140 °C) to reduce polysaccharide content via dehydration. This approach has lower environmental impact and higher economic efficiency compared to incineration and anaerobic digestion of sewage sludge. This work provides a new perspective on the high-value utilization of SS and offers a novel approach to developing bio-adhesives for the wood industry.

The Effect of Organic Matter from Sewage Sludge as an Interfacial Layer on the Surface of Nano-Al and Fluoride

Due to its high reactivity, the nano aluminum particle (n-Al) has attracted more attention in energetic materials but is easily oxidized during processing. In order to realize sewage sludge (SS) resource and n-Al coating, the organic matter was extracted from SS, using the deep eutectic solvent method due to its strong dissolving capacity, and then the organic matter was pretreated by ball milling, which was used as an interfacial layer between n-Al and fluoride. It was found that organic matter was successfully extracted from SS. The main organic matter is proteins. The ball milling method can effectively destroy the secondary structure of proteins to release more active functional groups. During the pretreatment, the Maillard reaction broke the proteins structure to form more active low molecular weight compounds. It was confirmed that n-Al can be coated by PBSP under mild conditions to form a uniform core-shell structure. PFOA can effectively coat the n-Al@PBSP to form n-Al@PBSP/PFOA, which can enhance the combustion of n-Al. The gas phase flame temperature can notably improve to 2892 K. The reaction mechanism between n-Al and coating was analyzed. The results could help SS treatment and provide new insights for n-Al coating and SS-based organic matter recovery and utilization.

Extraction and application of extracellular polymeric substances from fungi

Extracellular polymeric substances (EPS) are extracellular metabolites of microorganisms, highly associated with microbial function, adaptation, and growth. The main compounds in EPS have been revealed to be proteins, polysaccharides, nucleic acids, humic substances, lipids, etc. EPS are not only biomass, but also a biogenic material. EPS have high specific surface, abundant functional groups, and excellent degradability. In addition, they are more extensible to the environment than the microbial cells themselves, which exhibits their huge advantages. Therefore, they have been applied in many fields, such as the environment, ecosystem, basic commodities, and medicine. However, the functions of EPS highly depend on the suitable extraction process, as different extraction methods have different effects on their composition, structure, and function. There are many types of EPS extraction methods, in which physical and chemical methods have been widely utilized. This review summarizes the extraction methods and applications of EPS. In addition, it considers some important gaps in current knowledge, and indicates perspectives of EPS for their future study.

Granule formation mechanism, key influencing factors, and resource recycling in aerobic granular sludge (AGS) wastewater treatment: A review

The high-efficiency and additionally economic benefits generated from aerobic granular sludge (AGS) wastewater treatment have led to its increasing popularity among academics and industrial players. The AGS process can recycle high value-added biomaterials including extracellular polymeric substances (EPS), sodium alginate-like external polymer (ALE), polyhydroxyfatty acid (PHA), and phosphorus (P), etc., which can serve various fields including agriculture, construction, and chemical while removing pollutants from wastewaters. The effects of various key operation parameters on formation and structural stability of AGS are comprehensively summarized. The degradable metabolism of typical pollutants and corresponding microbial diversity and succession in the AGS wastewater treatment system are also discussed, especially with a focus on emerging contaminants removal. In addition, recent attempts for potentially effective production of high value-added biomaterials from AGS are proposed, particularly concerning improving the yield, quality, and application of these biomaterials. This review aims to provide a reference for in-depth research on the AGS process, suggesting a new alternative for wastewater treatment recycling.

Celebrating 50 years of microbial granulation technologies: From canonical wastewater management to bio-product recovery

Microbial granulation technologies (MGT) in wastewater management are widely practised for more than fifty years. MGT can be considered a fine example of human innovativeness-driven nature wherein the manmade forces applied during operational controls in the biological process of wastewater treatment drive the microbial communities to modify their biofilms into granules. Mankind, over the past half a century, has been refining the knowledge of triggering biofilm into granules with some definite success. This review captures the journey of MGT from inception to maturation providing meaningful insights into the process development of MGT-based wastewater management. The full-scale application of MGT-based wastewater management is discussed with an understanding of functional microbial interactions within the granule. The molecular mechanism of granulation through the secretion of extracellular polymeric substances (EPS) and signal molecules is also highlighted in detail. The recent research interest in the recovery of useful bioproducts from the granular EPS is also emphasized.

Potential interactive effect on biomass and bio-polymeric substances of microalgal-bacterial aerobic granular sludge as a valuable resource for sustainable development

The algal/bacterial biomass and extracellular polymeric substances (EPSs) existing in microalgal-bacterial aerobic granular sludge (MB-AGS) offer a promising bioresource. The current review-based paper presents a systematic overview of the compositions and interactions (gene transfer, signal transduction, and nutrient exchange) of microalgal and bacteria consortia, the role of cooperative or competitive partnerships of MB-AGS in the treatment of wastewater and recovery of resource, and the environmental/operational factors affecting their interactions and EPS production. Moreover, a brief notes is given on the opportunities and major challenges of utilizing the microalgal-bacterial biomass and EPS for phosphorus and polysaccharides chemical recovery, renewable energy (i.e. biodiesel, hydrogen, electricity) production. Overall, this compact review will pave the way for developing MB-AGS future biotechnology.

Simultaneous removal of nitrate, lead, and tetracycline by a fixed-biofilm reactor assembled with kapok fiber and sponge iron: Comparative analysis of operating conditions and biotic community

In recent years, under the condition of lack of carbon source, the presence of composite micro-pollutants make the removal of nitrate seriously damaged, and to find a suitable way to solve this problem is imminent. A fixed-biofilm carrier modified by mixing sponge iron (SI) and kapok fiber (KF) combined with strain Zoogloea sp. FY6 was constructed in this study to get a fixed-biofilm reactor with merit denitrification performance. By adjusting the operation parameters, it can be concluded that when the carbon to nitrogen (C/N) ratio was 1.5, the hydraulic retention time (HRT) was 6.0 h, and the pH was 6.0, the nitrate removal efficiency (NRE) of the fixed-biofilm reactor was up to 95.4% (2.95 mg L^-1 h^-1). In addition, the fixed-biofilm reactor constructed in this study can remove lead (Pb²⁺) and tetracycline (TC) excellently in the presence of SI and Zoogloea sp. FY6, and the denitrification performance can still maintain a high level under the influence of different concentrations of Pb²⁺ and TC. Furthermore, the addition of SI not only removes the compound pollutants, but also protects the toxicity of the pollutant inflow in the bioreactor, and the metabolic process of microorganisms in the bioreactor also removes some of the compound pollutants. The high-throughput data showed the abundance of strain Zoogloea sp. FY6 was still the highest value under the influence of various pollutants, and the metagenomic prediction showed that the fixed-biofilm reactor had perfect denitrification process and iron redox cycle benefits. This study provides a valuable reference for sustainable utilization of natural biological resources and reduction of material costs in wastewater treatment plants (WWTPs).

Calcium Alginate Production through Forward Osmosis with Reverse Solute Diffusion and Mechanism Analysis

Calcium alginate (Ca-Alg) is a novel target product for recovering alginate from aerobic granular sludge. A novel Ca-Alg production method was proposed herein where Ca-Alg was formed in a sodium alginate (SA) feed solution (FS) and concentrated via forward osmosis (FO) with Ca²⁺ reverse osmosis using a draw solution of CaCl₂. An abnormal reverse solute diffusion was observed, with the average reverse solute flux (RSF) decreasing with increasing CaCl₂ concentrations, while the average RSF increased with increasing alginate concentrations. The RSF of Ca²⁺ in FS decreased continuously as the FO progressed, using 1.0 g/L SA as the FS, while it increased initially and later decreased using 2.0 and 3.0 g/L SA as the FS. These results were attributed to the Ca-Alg recovery production (CARP) formed on the FO membrane surface on the feed side, and the percentage of Ca²⁺ in CARP to total Ca²⁺ reverse osmosis reached 36.28%. Scanning electron microscopy and energy dispersive spectroscopy also verified CARP existence and its Ca²⁺ content. The thin film composite FO membrane with a supporting polysulfone electrospinning nanofiber membrane layer showed high water flux and RSF of Ca²⁺, which was proposed as a novel FO membrane for Ca-Alg production via the FO process with Ca²⁺ reverse diffusion. Four mechanisms including molecular sieve role, electrification of colloids, osmotic pressure of ions in CARP, and FO membrane structure were proposed to control the Ca-Alg production. Thus, the results provide further insights into Ca-Alg production via FO along with Ca²⁺ reverse osmosis.

Characterization of magnetite assisted anammox granules based on in-depth analysis of extracellular polymeric substance (EPS)

Magnetite can be considered as an iron-rich carrier particles that can be ionized into Fe²⁺ and Fe³⁺ which improves the activity and aggregation of anammox bacteria. Three samples from this carrier assisted granulation reactor with size groups including Flocs, FL (0-300 µm), Small Granules, SG (300-500 µm) and Large Granules, LG (500-1000 µm) were used in this study. It was observed that as the granule size increased, the iron-rich carrier content increased, and their active crystals improved the microbial cell density. Specific anammox activity (SAA) was 34.63 ± 5.02, 55.29 ± 5.14, and 63.81 ± 7.50 mg-N/g-VSS/d for FL, SG and LG, respectively. In addition, in heme c content of LG was 31.5 % higher than SG and 62.9 % higher than FL. An in-depth study into the extracellular polymeric substances (EPS) showed that the secretion intensity of essential proteins followed the order of FL < SG < LG in loosely bound EPS and FL > SG > LG in tightly bound EPS. Functional group analysis confirmed that the hydrophobic CN and NH stretching vibration band had almost 3.5 times higher transmittance intensity in LG than the other sizes and the corresponding ratio of α-helix/(β sheet + random coil) in secondary derivative proteins analysis showed tightness in the protein structures of FL. The relative abundance of Brocadia Sinica increased from 0 % in FL to a high of 20.46 % in LG. This study aims to communicate the essence of in-depth EPS analysis beyond the usual EPS yield and major contents of proteins (PN) and polysaccharides (PS) analysis.

Metagenomic and extracellular polymeric substances analysis reveals the mechanism of exogenous N-hexanoyl-L-homoserine lactone in alleviating the inhibition of perfluorooctanoic acid on anammox process

To alleviate the negative effects of perfluorooctanoic acid (PFOA) on nitrogen removal via anaerobic ammonia oxidation (anammox), an exogenous signaling factor (N-hexanoyl-L-homoserine lactone, C₆-HSL) was introduced into an anammox reactor. Results showed that 2 μmol/L C₆-HSL promoted the nitrogen removal efficiency of the anammox reactor under PFOA stress, with the removal efficiencies of ammonia and nitrite increasing from 79.7 ± 4.8 % and 80.8 ± 3.8 %, to 94.4 ± 4.3 % and 97.1 ± 3.8 %. Exogenous C₆-HSL enhanced the compactness of the extracellular proteins, and improved the sludge hydrophobicity. Meanwhile, C₆-HSL resulted in a microbial shift, with the relative abundance of Planctomycetes increasing from 30.2 % to 49.5 %. Candidatus Kuenenia stuttgartiensis replaced Candidatus Brocadia sp. BL1 as the dominant species, while the available space for other nitrogen-removing bacteria was reduced. Exogenous C₆-HSL promoted the expression of anammox-related genes, such as hzsB and hdh, while denitrifying genes were down-regulated. In addition, the relative abundance of HdtS, which synthesizes AHLs, increased by 0.02446%.

Genetic potential for exopolysaccharide synthesis in activated sludge bacteria uncovered by genome-resolved metagenomics

A good floc formation of activated sludge (AS) is crucial for solid-liquid separation and production of clean effluent during wastewater treatment. Floc formation is partly controlled by self-produced extracellular polymeric substances (EPS) such as exopolysaccharides, proteins, and nucleic acids. Little is known about the composition, structure, and function of EPS in AS and which bacteria produce them. To address this knowledge gap for the exopolysaccharides, we took advantage of 1083 high-quality metagenome-assembled genomes (MAGs) obtained from 23 Danish wastewater treatment plants. We investigated the genomic potential for exopolysaccharide biosynthesis in bacterial species typical in AS systems based on genome mining and gene synteny analyses. Putative gene clusters associated with the biosynthesis of alginate, cellulose, curdlan, diutan, hyaluronic acids, Pel, poly-β-1,6-N-acetyl-d-glucosamine (PNAG), Psl, S88 capsular polysaccharide, salecan, succinoglycan, and xanthan were identified and linked to individual MAGs, providing a comprehensive overview of the genome-resolved potential for these exopolysaccharides in AS bacteria. The approach and results provide a starting point for a more comprehensive understanding of EPS composition in wastewater treatment systems, which may facilitate a more refined regulation of the activated sludge process for improved stability.

Extracellular polymeric substances-antibiotics interaction in activated sludge: A review

Antibiotics, the most frequently prescribed drugs, have been widely applied to prevent or cure human and veterinary diseases and have undoubtedly led to massive releases into sewer networks and wastewater treatment systems, a hotspot where the occurrence and transformation of antibiotic resistance take place. Extracellular polymeric substances (EPS), biopolymers secreted via microbial activity, play an important role in cell adhesion, nutrient retention, and toxicity resistance. However, the potential roles of sludge EPS related to the resistance and removal of antibiotics are still unclear. This work summarizes the composition and physicochemical characteristics of state-of-the-art microbial EPS, highlights the critical role of EPS in antibiotics removal, evaluates their defense performances under different antibiotics exposures, and analyzes the typical factors that could affect the sorption and biotransformation behavior of antibiotics. Next, interactions between microbial EPS and antibiotic resistance genes are analyzed. Future perspectives, especially the engineering application of microbial EPS for antibiotics toxicity detection and defense, are also emphatically stressed.

Evaluating the role of algae in algal-bacterial granular sludge: Nutrient removal, microbial community and granular characteristics

Algal-bacterial granular sludge (ABGS) and bacterial granular sludge (BGS, control group) were operated over 240 days to investigate the role of algae in treating synthetic municipal wastewater. The results showed that algae significantly improved the removal efficiency of total nitrogen (TN). The nitrogen removal load of ABGS was 2.6 mg-N/g-VSS/day (22.8 %, light) and 1.1 mg-N/g-VSS/day (9.6 %, dark) higher than that of BGS, respectively, which was attributed to algae enhanced NH₃-N removal capacity in the anaerobic stage and increased the utilization efficiency of organics in denitrification. Algae increased the relative abundance of denitrifying bacteria, and ABGS (28.83 %) was higher than BGS (14.28 %). Moreover, the dominant phylum of algae was Chlorophyta (98.39 %), the chlorophyll-a was sustained at 1.28 ± 0.26 mg/g-VSS. Algae significantly increased the content of extracellular polymeric substances (EPS), and the increased polysaccharide came from the tightly bound EPS. This study expands the understanding of the role of algae in ABGS.

A review on recovery of extracellular biopolymers from flocculent and granular activated sludges: Cognition, key influencing factors, applications, and challenges

A reasonable recovery of excess sludge may shift the waste into wealth. Recently an increasing attention has been paid to the recycling of extracellular biopolymers from conventional and advanced biological wastewater treatment systems such as flocculent activated sludge (AS), bacterial aerobic granular sludge (AGS), and algal-bacterial AGS processes. This review provides the first overview of current research developments and future directions in the recovery and utilization of high value-added biopolymers from the three types of sludge. It details the discussion on the recent evolvement of cognition or updated knowledge on functional extracellular biopolymers, as well as a comprehensive summary of the operating conditions and wastewater parameters influencing the yield, quality, and functionality of alginate-like exopolymer (ALE). In addition, recent attempts for potential practical applications of extracellular biopolymers are discussed, suggesting research priorities for overcoming identification challenges and future prospects.

Two strategies of stubborn biofouling strains surviving from NaClO membrane cleaning: EPS shielding and/or quorum sensing

The declined performance of repeated chemically-enhanced-backwashing (CEB) seriously hampered the sustainable operation of membrane bioreactor (MBR) in long-term, and could be partially attributed to the strengthened anti-cleaning properties of residual stubborn microbes. Although plenty of research has been done towards either the model strains or the whole post-CEB microbial community, little was known about the resisting behavior of practical stubborn strains when confronting oxidative stresses induced by NaClO. Hence, this study isolated 21 strains from samples in a large-scale MBR plant with routine CEB treatment. To unravel how they survive and affect membrane fouling, their anti-oxidation ability, fouling potential and quorum sensing (QS) effect before and after NaClO stimuli were evaluated. The composition and molecular weight distribution of extracellular polymeric substance (EPS) were also investigated to understand their roles during the anti-CEB process. It was found that typical stubborn strains tended to secrete more EPS as protective shields, where polysaccharides (especially the ones >1 kDa) made major contribution. However, sometimes EPS could not well resist the stimuli, with consequent low survival rate and high intracellular ROS level. Under such circumstances, stubborn strains would rather choose to be sensitive with surged QS level and quick population regrowth to maintain vitality under the oxidative stresses. Both strategies aggravated biofouling and eventually enhanced the anti-cleaning properties of biofilm.

Effect of Seed Sludge Type on Aerobic Granulation, Pollutant Removal and Microbial Community in a Sequencing Batch Reactor Treating Real Textile Wastewater

The aerobic granulation, pollutant removal, and microbial community in real textile wastewater (TWW) treatment were compared using conventional activated sludge (CAS) and preformed aerobic granular sludge (AGS) in synthetic wastewater as seed in two reactors, reactor-1 (R1) and reactor-2 (R2), respectively. The results showed that complete granulation was achieved in R1 (sludge volume index at 5 min (SVI₅) and 30 min (SVI₃₀): 19.4 mL/g; granule size: 210 μm) within 65 days, while it only required 28 days in R2 (SVI₅ and SVI₃₀: 27.3 mL/g; granule size: 496 μm). The removal of COD, NH₄⁺-N and TN in R1 (49.8%, 98.8%, and 41.6%) and R2 (53.6%, 96.9%, and 40.8%) were comparable in 100% real TWW treatment, but stable performance was achieved much faster in R2. The real TWW had an inhibitory effect on heterotrophic bacteria activity, but it had no inhibition on ammonia-oxidizing bacteria activity. AGS with a larger particle size had a higher microbial tolerance to real TWW. Furthermore, filamentous Thiothrix in the AGS in R2 disappeared when treating real TWW, leading to the improvement of sludge settleability. Thus, seeding preformed AGS is suggested as a rapid start-up method for a robust AGS system in treating real TWW.

A comprehensive review on recent advances in preparation, physicochemical characterization, and bioengineering applications of biopolymers

Biopolymers are mainly the polymers which are created or obtained from living creatures such as plants and bacteria rather than petroleum, which has traditionally been the source of polymers. Biopolymers are chain-like molecules composed of repeated chemical blocks derived from renewable resources that may decay in the environment. The usage of biomaterials is becoming more popular as a means of reducing the use of non-renewable resources and reducing environmental pollution produced by synthetic materials. Biopolymers' biodegradability and non-toxic nature help to maintain our environment clean and safe. This study discusses how to improve the mechanical and physical characteristics of biopolymers, particularly in the realm of bioengineering. The paper begins with a fundamental introduction and progresses to a detailed examination of synthesis and a unique investigation of several recent focused biopolymers with mechanical, physical, and biological characterization. Biopolymers' unique non-toxicity, biodegradability, biocompatibility, and eco-friendly features are boosting their applications, especially in bioengineering fields, including agriculture, pharmaceuticals, biomedical, ecological, industrial, aqua treatment, and food packaging, among others, at the end of this paper. The purpose of this paper is to provide an overview of the relevance of biopolymers in smart and novel bioengineering applications.

Graphical abstract

The Graphical abstract represents the biological sources and applications of biopolymers. Plants, bacteria, animals, agriculture wastes, and fossils are all biological sources for biopolymers, which are chemically manufactured from biological monomer units, including sugars, amino acids, natural fats and oils, and nucleotides. Biopolymer modification (chemical or physical) is recognized as a crucial technique for modifying physical and chemical characteristics, resulting in novel materials with improved capabilities and allowing them to be explored to their full potential in many fields of application such as tissue engineering, drug delivery, agriculture, biomedical, food industries, and industrial applications.

Carbon source affects the resource recovery in aerobic granular sludge systems treating wastewater

This study evaluated the influence of carbon sources on alginate-like exopolymers (ALE) and tryptophan (Trp) biosynthesis in the aerobic granular sludge (AGS). With acetate, the highest biopolymers levels, per gram of volatile suspended solids (VSS) (418.7 mgALE∙g^-1 and 4.1 mgTrp∙gVSS^-1), were found likely due to biomass loss throughout the operation, which resulted in lower sludge age (4-7 days) and shorter famine period. During granulation, encouraging results on ALE production were obtained with propionate (>250 mgALE∙gVSS^-1), significantly higher than those found with glycerol, glucose, and sucrose. Regarding tryptophan production, propionate and glycerol proved to be good substrates, although the content was still lower than acetate (1.6 mgTrp∙gVSS^-1). Granules fed with glucose showed the worst results compared to the other substrates (38.5 mgALE∙VSS^-1 and 0.6 mgTrp∙gVSS^-1) due to the filamentous microorganisms' abundance found. Therefore, this study provides insights to value the production of compounds of industrial interest in AGS systems.

A comparative study on simultaneous recovery of phosphorus and alginate-like exopolymers from bacterial and algal-bacterial aerobic granular sludges: Effects of organic loading rate

The effects of organic loading rate (OLR) on simultaneous phosphorus (P) and alginate-like exopolymers (ALE) recovery from bacterial aerobic granular sludge (AGS) and algal-bacterial AGS were examined and compared during 70 days' operation. With the increase of OLR (0.6-1.2 g COD/(L·day)), both AGS showed good settleability and granular strength with P bioavailability > 92% (Stage III). The moderate increase in OLR had a positive influence on simultaneous recovery of P and ALE. On day 60, the contents of ALE and guluronic acid/guluronic acid (GG) blocks reached the highest in algal-bacterial AGS, about 13.37 and 2.13 mg/g-volatile suspended solids (VSS), respectively. Meanwhile, about daily 0.55 kg of P is estimated to be recovered from the wastewater treatment plant with a treatment capacity of 10,000 m³/day. P mass balance analysis during ALE extraction from both AGS was conducive to further evaluation of P removal pathway and its application potentials.

Cyanophycin Granule Polypeptide: a Neglected High Value-Added Biopolymer, Synthesized in Activated Sludge on a Large Scale

Recovery of microbial synthetic polymers with high economic value and market demand in activated sludge has attracted extensive attention. This work analyzed the synthesis of cyanophycin granule peptide (CGP) in activated sludge and its adsorption capacity for heavy metals and dyes. The distribution and expression of synthetic genes for eight biopolymers in two wastewater treatment plants (WWTPs) were analyzed by metagenomics and metatranscriptomics. The results indicate that the abundance and expression level of CGP synthase (cphA) are similar to those of polyhydroxyalkanoate polymerase, implying high synthesis of CGP in activated sludges. CGP in activated sludge is mainly polymerized from aspartic acid and arginine, and its secondary structure is mainly β-sheet. The crude yields of CGP are as high as 104 ± 26 and 76 ± 13 mg/g dry sludge in winter and in summer, respectively, comparable to those of polyhydroxyalkanoate and alginate. CGP has a stronger adsorption capacity for anionic pollutants (Cr (VI) and methyl orange) than for cationic pollutants because it is rich in guanidine groups. This study highlights prospects for recovery and application of CGP from WWTPs. IMPORTANCE The conversion of organic pollutants into bioresources by activated sludge can reduce the carbon dioxide emission of wastewater treatment plants. Identification of new high value-added biopolymers produced by activated sludge is beneficial to recover bioresources. Cyanophycin granule polypeptide (CGP), first discovered in cyanobacteria, has unique chemical and material properties suitable for industrial food, medicine, cosmetics, water treatment, and agriculture applications. Here, we revealed for the first time that activated sludge has a remarkable ability to produce CGP. These findings could further facilitate the conversion of wastewater treatment plants into resource recycling plants.

How can the addition of extracellular polymeric substances (EPS)-based bioflocculant affect aerobic granular sludge (AGS)?

The ability of extracellular polymeric substances (EPS) recovered from aerobic granular sludge (AGS) to act as bioflocculant was tested in a pilot-scale sequencing batch reactor (SBR), fed with low-strength municipal wastewater. EPS were compared with the addition of Na-alginate as a standardized biopolymer. The optimal dosage of both biopolymers was determined through jar-test assays (400 mg L^-1 of Na-alginate in a 250 mg Ca L^-1 and 50 mg L^-1 of EPS in pH of 2 ± 0.2). The addition of Na-alginate (Operational Period I- OP-I) and EPS (Operational Period II - OP-II) led to increased adhesion of particles with 2.9 ± 0.45 and 1.3 ± 0.3 g TSS L^-1 during OP-I and OP-II, respectively, and fast settling biomass (SVI₃₀ between 68 and 78 mL g^-1). Granule predominance occurred at early stages of OP-I (day 37) and OP-II (day 44), presenting diameters mainly within the 212-600 μm range. The reactor showed removal efficiencies of 85% for biochemical oxygen demand (BOD) and above 50% for N-NH₄ during the study periods. Furthermore, the addition of EPS as a bioflocculant promoted a substantial increase in polysaccharides (PS = 153.01 ± 121 mg g_VSS^-1) and proteins (PN = 121.96 ± 69 mg g_VSS^-1), while the addition of Na-alginate affected mostly the PS content (87 ± 24 mg g_VSS^-1). The microbial community shifted mainly from Betaproteobacteria (45%) during OP-I to Alphaproteobacteria (64%) in OP-II. Therefore, EPS affected both physical-chemical and microbial features of the AGS biomass without any change in treatment efficiencies. EPS is a promising resource to be recovered from aerobic granular sludge and to be used as an alternative and sustainable bioflocculant.

Multidisciplinary characterization of nitrogen-removal granular sludge: A review of advances and technologies

Nitrogen-removal granular sludge (NRGS) is a promising technology in wastewater treatment, with advantages of efficient nitrogen removal, less footprint, lower sludge production and energy consumption, and is a way for wastewater treatment plants to achieve carbon-neutrality. Aerobic granular sludge (AGS) and anammox granular sludge (AnGS) are two typical NRGS technologies that have attracted extensive attention. Mounting evidence has shown strong associations between NRGS properties and the status of NRGS systems; however, a holistic view is still missing. The aim of this article is to provide an overview of NRGS with an emphasis on characterization. Specifically, the integrated nitrogen transformation pathways inside NRGS and the performance of NRGS treating various wastewaters are discussed. NRGS properties are categorized as physical-, chemical-, biological- and systematical ones, presenting current advances and corresponding characterization technologies. Finally, the future prospects for furthering the mechanistic understanding and engineering application of NRGS are proposed. Overall, the technological advancements in characterization have greatly contributed to understanding NRGS properties, which are potential factors for optimizing the performance and evaluating the working status of NRGS. This review will provide guidance in characterizing NRGS properties and boost the introduction of novel characterization technologies.

Recovery Techniques Enabling Circular Chemistry from Wastewater

In an era where it becomes less and less accepted to just send waste to landfills and release wastewater into the environment without treatment, numerous initiatives are pursued to facilitate chemical production from waste. This includes microbial conversions of waste in digesters, and with this type of approach, a variety of chemicals can be produced. Typical for digestion systems is that the products are present only in (very) dilute amounts. For such productions to be technically and economically interesting to pursue, it is of key importance that effective product recovery strategies are being developed. In this review, we focus on the recovery of biologically produced carboxylic acids, including volatile fatty acids (VFAs), medium-chain carboxylic acids (MCCAs), long-chain dicarboxylic acids (LCDAs) being directly produced by microorganisms, and indirectly produced unsaturated short-chain acids (USCA), as well as polymers. Key recovery techniques for carboxylic acids in solution include liquid-liquid extraction, adsorption, and membrane separations. The route toward USCA is discussed, including their production by thermal treatment of intracellular polyhydroxyalkanoates (PHA) polymers and the downstream separations. Polymers included in this review are extracellular polymeric substances (EPS). Strategies for fractionation of the different fractions of EPS are discussed, aiming at the valorization of both polysaccharides and proteins. It is concluded that several separation strategies have the potential to further develop the wastewater valorization chains.

Heavy metal biosorption by Extracellular Polymeric Substances (EPS) recovered from anammox granular sludge

The recovery and conversion of Extracellular Polymeric Substances (EPS) from sewage sludge into bio-based commodities might improve the economics and environmental sustainability of wastewater treatment. This contribution explores the application of EPS from anammox granular waste sludge as biosorbent for the removal of heavy metals, specifically lead, copper, nickel, and zinc. Adsorption capacities equivalent or higher than well-established adsorbent media emerged from single-metal biosorption studies (up to 84.9, 52.8, 21.7 and 7.4 mg/gTS_EPS for Pb²⁺, Cu²⁺, Ni²⁺ and Zn²⁺, respectively). Combining spectroscopic techniques, a mechanistic hypothesis for metal biosorption, based on a combination of electrostatic interaction, ion exchange, complexation, and precipitation, was proposed. The adsorption mechanisms of extracted EPS and non-extracted EPS in the native biomass were indirectly compared by means of single-metal biosorption studies performed with pristine granules (adsorbing up to 103.7, 36.1, 48.2 and 49.8 mg/gTSgranules of Pb²⁺, Cu²⁺, Ni²⁺, and Zn²⁺, respectively). In comparison with pristine anammox granules, EPS showed lower adsorption capacities except for copper and different adsorption pathways as postulated based on the adsorption data interpretation via theoretical models. The multi-metal biosorption tests excluded significant competitions among different heavy metals for the EPS binding sites, thus opening further scenarios for the treatment of complex wastewaters.

Simultaneous recovery of phosphorus and alginate-like exopolysaccharides from two types of aerobic granular sludge

Wastewater treatment plants are expected to realize not only pollutants removal from wastewater but also resources recovery such as phosphorus (P) and alginate-like exopolysaccharides (ALE) from the produced sludge. In this study, ALE extraction and fractionation from the same activated sludge-derived bacterial aerobic granular sludge (AGS) and algal-bacterial AGS were performed in addition to P fate examination during ALE recovery. Results showed that the ALE content recovered from algal-bacterial AGS was 8.81 ± 0.02 mg/g-volatile suspended solids (VSS), about 2.8 times higher than that from bacterial AGS when fed with the same synthetic wastewater. Moreover, the mannuronic acid to guluronic acid (MG) blocks accounted for the largest proportion of ALE from the two granular sludges. In particular, the extracellular polymeric substances (EPS) extracted from bacterial and algal-bacterial AGS contained about 25.10 ± 1.85 and 19.53 ± 0.04 mg-P/g-SS, respectively, and both granular sludges possessed high P bioavailability of 97-99%.

Extraction of the Bacterial Extracellular Polysaccharide FucoPol by Membrane-Based Methods: Efficiency and Impact on Biopolymer Properties

In this study, membrane-based methods were evaluated for the recovery of FucoPol, the fucose-rich exopolysaccharide (EPS) secreted by the bacterium Enterobacter A47, aiming at reducing the total water consumption and extraction time, while keeping a high product recovery, thus making the downstream procedure more sustainable and cost-effective. The optimized method involved ultrafiltration of the cell-free supernatant using a 30 kDa molecular weight cut-off (MWCO) membrane that allowed for a 37% reduction of the total water consumption and a 55% reduction of the extraction time, compared to the previously used method (diafiltration-ultrafiltration with a 100 kDa MWCO membrane). This change in the downstream procedure improved the product’s recovery (around 10% increase) and its purity, evidenced by the lower protein (8.2 wt%) and inorganic salts (4.0 wt%) contents of the samples (compared to 9.3 and 8.6 wt%, respectively, for the previously used method), without impacting FucoPol’s sugar and acyl groups composition, molecular mass distribution or thermal degradation profile. The biopolymer’s emulsion-forming and stabilizing capacity was also not affected (emulsification activity (EA) with olive oil, at a 2:3 ratio, of 98 ± 0% for all samples), while the rheological properties were improved (the zero-shear viscosity increased from 8.89 ± 0.62 Pa·s to 17.40 ± 0.04 Pa·s), which can be assigned to the higher purity degree of the extracted samples. These findings demonstrate a significant improvement in the downstream procedure raising FucoPol’s recovery, while reducing water consumption and operation time, key criteria in terms of process economic and environmental sustainability. Moreover, those changes improved the biopolymer’s rheological properties, known to significantly impact FucoPol’s utilization in cosmetic, pharmaceutical or food products.

Performance and responses of aerobic granular sludge at different concentrations of graphene oxide after a single administered dose

To investigate the impact of graphene oxide (GO) under different concentrations (0, 50, 100, 150, and 200 mg/L) on aerobic granular sludge (AGS) after a single administered dose, the performance of nitrogen removal, microbial enzymatic activity, extracellular polymeric substances (EPSs), and microbial community structure was analyzed in batch tests. The results showed that the impact of GO concentrations on AGS was dose- and time-dependent. Short-term GO exposure could accelerate the nitrification process of AGS, while relatively concentrations (≥100 mg/L) inhibited the process when present for extended periods of time. The microbial enzymatic activity showed similar tendency. The production of lactate dehydrogenase release (LDH) in 200 mg/L group was increased 48.04% and EPS contents decreased 30.06% compared to the control group at 30th day and showed that high concentrations of GO have toxic effects on AGS. The microbial bacteria responded differently to the stimulation of different concentrations of GO. PRACTITIONER POINTS: GO affected AGS system performance in concentration- and time-dependent manners. The nitrification rate of AGS increased in the short term and reversed over time. Long-term exposure to high GO concentrations caused toxicity to AGS. Different microorganisms had diverse responses to GO concentrations.

Wastewater Valorization: Practice around the World at Pilot- and Full-Scale

Over the last few years, wastewater treatment plants (WWTPs) have been rebranded as water resource recovery facilities (WRRFs), which recognize the resource recovery potential that exists in wastewater streams. WRRFs contribute to a circular economy by not only producing clean water but by recovering valuable resources such as nutrients, energy, and other bio-based materials. To this aim, huge efforts in technological progress have been made to valorize sewage and sewage sludge, transforming them into valuable resources. This review summarizes some of the widely used and effective strategies applied at pilot- and full-scale settings in order to valorize the wastewater treatment process. An overview of the different technologies applied in the water and sludge line is presented, covering a broad range of resources, i.e., water, biomass, energy, nutrients, volatile fatty acids (VFA), polyhydroxyalkanoates (PHA), and exopolymeric substances (EPS). Moreover, guidelines and regulations around the world related to water reuse and resource valorization are reviewed.

Marine Gel Interactions with Hydrophilic and Hydrophobic Pollutants

Microgels play critical roles in a variety of processes in the ocean, including element cycling, particle interactions, microbial ecology, food web dynamics, air-sea exchange, and pollutant distribution and transport. Exopolymeric substances (EPS) from various marine microbes are one of the major sources for marine microgels. Due to their amphiphilic nature, many types of pollutants, especially hydrophobic ones, have been found to preferentially associate with marine microgels. The interactions between pollutants and microgels can significantly impact the transport, sedimentation, distribution, and the ultimate fate of these pollutants in the ocean. This review on marine gels focuses on the discussion of the interactions between gel-forming EPS and pollutants, such as oil and other hydrophobic pollutants, nanoparticles, and metal ions.

Resource recovery in aerobic granular sludge systems: is it feasible or still a long way to go?

Lately, wastewater treatment plants are much often being designed as wastewater-resource factories inserted in circular cities. Among biological treatment technologies, aerobic granular sludge (AGS), considered an evolution of activated sludge (AS), has received great attention regarding its resource recovery potential. This review presents the state-of-the-art concerning the influence of operational parameters on the recovery of alginate-like exopolysaccharides (ALE), tryptophan, phosphorus, and polyhydroxyalkanoates (PHA) from AGS systems. The carbon to nitrogen ratio was identified as a parameter that plays an important role for the optimal production of ALE, tryptophan, and PHA. The sludge retention time effect is more pronounced for the production of ALE and tryptophan. Additionally, salinity levels in the bioreactors can potentially be manipulated to increase ALE and phosphorus yields simultaneously. Some existing knowledge gaps in the scientific literature concerning the recovery of these resources from AGS were also identified. Regarding industrial applications, tryptophan has the longest way to go. On the other hand, ALE production/recovery could be considered the most mature process if we take into account that existing alternatives for phosphorus and PHA production/recovery are optimized for activated sludge rather than granular sludge. Consequently, to maintain the same effectiveness, these processes likely could not be applied to AGS without undergoing some modification. Therefore, investigating to what extent these adaptations are necessary and designing alternatives is essential.

Scaling-up microbial community-based polyhydroxyalkanoate production: status and challenges

Conversion of organic waste and wastewater to polyhydroxyalkanoates (PHAs) offers a potential to recover valuable resources from organic waste. Microbial community-based PHA production systems have been successfully applied in the last decade at lab- and pilot-scales, with a total of 19 pilot installations reported in the scientific literature. In this review, research at pilot-scale on microbial community-based PHA production is categorized and subsequently analyzed with focus on feedstocks, enrichment strategies, yields of PHA on substrate, biomass PHA content and polymer characterization. From this assessment, the challenges for further scaling-up of microbial community-based PHA production are identified.