A review on polyaniline-based materials applications in heavy metals removal and catalytic processes

Aerogels of Polypyrrole/Tannic Acid with Nanofibrillated Cellulose for the Removal of Hexavalent Chromium Ions

The preparation of conducting polymer aerogels is an effective strategy to produce innovative materials with enhanced physicochemical properties. Herein, polypyrrole (PPy) aerogels were oxidatively prepared in the presence of tannic acid (TA) with different concentrations (2.5, 5, and 10% mole ratio to pyrrole monomer) under freezing conditions. Nanofibrillated cellulose (NFC) was added during the PPy/TA synthesis to enhance mechanical stability. The effect of TA concentration on the aerogels' morphology, conductivity, thermal stability, and adsorption capacity was investigated. The conductivity of 9.6 ± 1.7 S cm-1 was achieved for PPy/TA prepared with 2.5% TA, which decreased to 0.07 ± 0.01 S cm-1 when 10% TA was used. PPy/TA aerogels have shown high efficacy in removing Cr(VI) ions from aqueous solutions. Adsorption experiments revealed that all the aerogels follow pseudo-second-order kinetics. PPy/TA prepared with NFC has a maximum adsorption capacity of 549.5 mg g-1.

Unveiling the potential of PANI@MnO2@rGO ternary nanocomposite in energy storage and gas sensing

The development of advanced materials for energy storage and gas sensing applications has gained significant attention in recent years. In this study, we synthesized and characterized PANI@MnO2@rGO ternary nanocomposites (NCs) to explore their potential in supercapacitors and gas sensing devices. The ternary NCs were synthesized through a multi-step process involving the hydrothermal synthesis of MnO2 nanoparticles, preparation of PANI@rGO composites and the assembly to the ternary PANI@MnO2@rGO ternary NCs. The structural, morphological, and compositional characteristics of the materials were thoroughly analyzed using techniques such as XRD, FESEM, TEM, FTIR, and Raman spectroscopy. In the realm of gas sensing, the ternary NCs exhibited excellent performance as NH3 gas sensors. The optimized operating temperature of 100 °C yielded a peak response of 15.56 towards 50 ppm NH3. The nanocomposites demonstrated fast response and recovery times of 6 s and 10 s, respectively, and displayed remarkable selectivity for NH3 gas over other tested gases. For supercapacitor applications, the electrochemical performance of the ternary NCs was evaluated using cyclic voltammetry and galvanostatic charge-discharge techniques. The composites exhibited pseudocapacitive behavior, with the capacitance reaching up to 185 F/g at 1 A/g and excellent capacitance retention of approximately 88.54% over 4000 charge-discharge cycles. The unique combination of rGO, PANI, and MnO2 nanoparticles in these ternary NCs offer synergistic advantages, showcasing their potential to address challenges in energy storage and gas sensing technologies.

Environmental fate of aquatic pollutants and their mitigation by phycoremediation for the clean and sustainable environment: A review

Emerging pollutants such as natural and manufactured chemicals, insecticides, pesticides, surfactants, and other biological agents such as personal care products, cosmetics, pharmaceuticals, and many industrial discharges hamper the aquatic environment. Nanomaterials and microplastics, among the categories of pollutants, can directly interfere with the marine ecosystem and translate into deleterious effects for humans and animals. They are either uncontrolled or poorly governed. Due to their known or suspected effects on human and environmental health, some chemicals are currently causing concern. The aquatic ecology is at risk from these toxins, which have spread worldwide. This review assesses the prevalence of emerging and hazardous pollutants that have effects on aquatic ecosystems and contaminated water bodies and their toxicity to non-target organisms. Microalgae are found to be a suitable source to remediate the above-mentioned risks. Microalgae based mitigation techniques are currently emerging approaches for all such contaminants, including the other categories that are discussed above. These studies describe the mechanism of phycoremediation, provide outrage factors that may significantly affect the efficiency of contaminants removal, and discuss the future directions and challenges of microalgal mediated remediations.

Waste-derived nanobiochar: A new avenue towards sustainable agriculture, environment, and circular bioeconomy

The greatest challenge for the agriculture sector in the twenty-first century is to increase agricultural production to feed the burgeoning global population while maintaining soil health and the integrity of the agroecosystem. Currently, the application of biochar is widely implemented as an effective means for boosting sustainable agriculture while having a negligible influence on ecosystems and the environment. In comparison to traditional biochar, nano-biochar (nano-BC) boasts enhanced specific surface area, adsorption capacity, and mobility properties within soil, allowing it to promote soil properties, crop growth, and environmental remediation. Additionally, carbon sequestration and reduction of methane and nitrous oxide emissions from agriculture can be achieved with nano-BC applications, contributing to climate change mitigation. Nonetheless, due to cost-effectiveness, sustainability, and environmental friendliness, waste-derived nano-BC may emerge as the most viable alternative to conventional waste management strategies, contributing to the circular bioeconomy and the broader goal of achieving the Sustainable Development Goals (SDGs). However, it's important to note that research on nano-BC is still in its nascent stages. Potential risks, including toxicity in aquatic and terrestrial environments, necessitate extensive field investigations. This review delineates the potential of waste-derived nano-BC for sustainable agriculture and environmental applications, outlining current advancements, challenges, and possibilities in the realms from a sustainability and circular bioeconomy standpoint.

A novel electrochemical aptasensor based on polyaniline and gold nanoparticles for ultrasensitive and selective detection of ascorbic acid

Ascorbic acid (AA) is involved in many physiological activities of the body and plays an important role in maintaining and promoting human health. It is also present in many natural and artificial foods. Therefore, the development of highly sensitive and accurate AA sensors is highly desirable for human health monitoring, as well as other commercial application fields. Herein, an ultrasensitive and selective electrochemical sensor based on an aptamer was developed for the determination of AA for the first time. The aptasensor was fabricated by modifying a composite made of polyaniline (PANI) and gold nanoparticles (AuNPs) on a glassy carbon electrode. The morphologies and electrochemical properties of the resulting electrodes were characterized by various analytical methods. The results indicated relatively good electrical conduction properties of PANI for accelerated electron transfer. The modification with AuNPs provided signal amplification, suitable for applications as novel platforms for the sensitive sensing of AA. Under optimized conditions, the proposed aptasensor displayed a wide linear response toward the detection of AA from 1.0 to 1.0 × 105 ng L-1 coupled with a low detection limit of 0.10 ng L-1. The sensor also exhibited excellent selectivity and high stability, with at least 2000-fold higher sensitivity than similar previously reported methods. Importantly, the aptasensor exhibited promising properties for the determination of AA in real fruits, vegetables, and infant milk powder, thereby showing potential for food analysis.

Coal Fly Ash Decorated with Graphene and Polyaniline Nanocomposites for Effective Adsorption of Hexavalent Chromium and Its Reuse for Photocatalysis

Coal fly ash was functionalized and modified with graphene oxide and polyaniline (CFA/GO/PANI nanocomposite) through hydrothermal synthesis, which was used for remediation of hexavalent chromium (Cr(VI)) ions. Batch adsorption experiments were carried out to investigate the effects of adsorbent dosage, pH, and contact time on the removal of Cr(VI). The ideal pH for this work was 2, and it was used for all other studies. The Cr(VI)-loaded spent adsorbent CFA/GO/PANI + Cr(VI) was reused as a photocatalyst for the degradation of bisphenol A (BPA). The CFA/GO/PANI nanocomposite removed Cr(VI) ions rapidly. The adsorption process was best described by pseudo-second-order kinetics and the Freundlich isotherm model. The CFA/GO/PANI nanocomposite demonstrated a high adsorption capacity of 124.72 mg/g for Cr(VI) removal. In addition, the Cr(VI)-loaded spent adsorbent played a significant role in the photocatalytic degradation of BPA with 86% degradation. The reuse of the Cr(VI)-loaded spent adsorbent as a photocatalyst presents a new solution for the reduction of secondary waste from the adsorption process.

Selective Adsorption Behavior and Mechanism for Cd(II) in Aqueous Solution with a Recoverable Magnetie-Surface Ion-Imprinted Polymer

A novel recoverable magnetic Cd(II) ion-imprinted polymer was synthesized on the surface of silica-coated Fe₃O₄ particles via the surface imprinting technique and chemical grafting method. The resulting polymer was used as a highly efficient adsorbent for the removal of Cd(II) ions from aqueous solutions. The adsorption experiments revealed that Fe₃O₄@SiO₂@IIP had a maximum adsorption capacity of up to 29.82 mg·g^-1 for Cd(II) at an optimal pH of 6, with the adsorption equilibrium achieved within 20 min. The adsorption process followed the pseudo-second-order kinetic model and the Langmuir isotherm adsorption model. Thermodynamic studies showed that the adsorption of Cd(II) on the imprinted polymer was spontaneous and entropy-increasing. Furthermore, the Fe₃O₄@SiO₂@IIP could rapidly achieve solid-liquid separation in the presence of an external magnetic field. More importantly, despite the poor affinity of the functional groups constructed on the polymer surface for Cd(II), we improved the specific selectivity of the imprinted adsorbent for Cd(II) through surface imprinting technology. The selective adsorption mechanism was verified by XPS and DFT theoretical calculations.

Polyaniline-Supported Nickel Oxide Flower for Efficient Nitrite Electrochemical Detection in Water

A modified electrode with conducting polymer (Polyaniline) and NiO nanoflowers was prepared to detect nitrite ions in drinking water. A simple method was used to prepare the NiO nanoflower (NiOnF). Several techniques characterized the as-prepared NiOnF to determine the chemical structure and surface morphology of the NiO, such as XRD, XPS, FT-IR, and TGA. The activity of the electrode toward nitrite sensing was investigated over a wide range of pH (i.e., 2 to 10). The amperometry method was used to determine the linear detection range and limit. Accordingly, the modified electrode GC/PANI/NiOnf showed a linear range of detection at 0.1-1 µM and 1-500 µM. At the same time, the limit of detection (LOD) was 9.7 and 64 nM for low and high concentrations, respectively. Furthermore, the kinetic characteristics of nitrite, such as diffusion and transport coefficients, were investigated in various media. Moreover, the charge transfer resistance was utilized for nitrite electrooxidation in different pH values by the electrochemical impedance technique (EIS). The anti-interfering criteria of the modified surfaces were utilized in the existence of many interfering cations in water (e.g., K⁺, Na⁺, Cu²⁺, Zn²⁺, Ba²⁺, Ca²⁺, Cr²⁺, Cd²⁺, Pd²⁺). A real sample of the Nile River was spiked with nitrite to study the activity of the electrode in a real case sample (response time ~4 s). The interaction between nitrite ions and NiO{100} surface was studied using DFT calculations as a function of adsorption energy.

Electrochemical performance optimization of the polyaniline electrodeposited on ITO substrate

We have elaborated polyaniline films on ITO substrate (indium tin oxide), by electrochemical process in different electrolytes (HCl, H2SO4, HNO3, and H3BO3), which allowed us to study the effect of the counter ion on electrochemical energy storage performances of polyaniline as electrode material in supercapacitors. The study of the different obtained films performances was carried out by cyclic voltammetry and galvanostatic charge-discharge method and is interpreted by the SEM technique. We found that there is a clear dependence on the specific capacitance of the counter ion. Justified by its porous structure, the PANI/ITO electrode doped with SO42- has the highest specific capacitance, 57.3 mF/cm2 at a current density of 0.2 mA/cm2 and 64.8 mF/cm2 at 5 mV/s. The deep analysis by Dunn's method allowed us to conclude that the faradic process dominates the energy storage in the case of PANI/ITO electrode elaborated in boric acid (99%). On the contrary, the capacitive character is the most contributory in the case of electrodes elaborated in H2SO4, HCl, and HNO3. The study at different potentials (0.80, 0.85, 0.90, 0.95, and 1.0 V/SCE) from 0.2 M monomer aniline showed that the deposition at 0.95 V/SCE leads to higher specific capacitance (24.3 mF/cm2 at scan rate 5 mV/s and 23.6 mF/cm2 at 0.2 mA/cm2) with a coulombic efficiency of 94%. By varying the concentration of the monomer while keeping a potential fixed at 0.95 V/SCE, we also found that the specific capacitance increases with monomeric concentration.

Preparation of a Polyaniline-Modified Hybrid Graphene Aerogel-Like Nanocomposite for Efficient Adsorption of Heavy Metal Ions from Aquatic Media

This paper considers the synthesis of a novel nanocomposite based on reduced graphene oxide and oxidized carbon nanotubes modified with polyaniline and phenol-formaldehyde resin and developed through the carbonization of a pristine aerogel. It was tested as an efficient adsorbent to purify aquatic media from toxic Pb(II). Diagnostic assessment of the samples was carried out through X-ray diffractometry, Raman spectroscopy, thermogravimetry, scanning and transmission electron microscopy, and infrared spectroscopy. The carbonized aerogel was found to preserve the carbon framework structure. The sample porosity was estimated through nitrogen adsorption at 77 K. It was found that the carbonized aerogel predominantly represented a mesoporous material having a specific surface area of 315 m²/g. After carbonization, an increase in smaller micropores occurred. According to the electron images, the highly porous structure of the carbonized composite was preserved. The adsorption capacity of the carbonized material was studied for liquid-phase Pb(II) extraction in static mode. The experiment results showed that the maximum Pb(II) adsorption capacity of the carbonized aerogel was 185 mg/g (at pH 6.0). The results of the desorption studies showed a very low desorption rate (0.3%) at pH 6.5 and a rate of about 40% in a strongly acidic medium.

Advances in Sorptive Removal of Hexavalent Chromium (Cr(VI)) in Aqueous Solutions Using Polymeric Materials

Sorptive removal of hexavalent chromium (Cr(VI)) bears the advantages of simple operation and easy construction. Customized polymeric materials are the attracting adsorbents due to their selectivity, chemical and mechanical stabilities. The mostly investigated polymeric materials for removing Cr(VI) were reviewed in this work. Assembling of robust functional groups, reduction of self-aggregation, and enhancement of stability and mechanical strength, were the general strategies to improve the performance of polymeric adsorbents. The maximum adsorption capacities of these polymers toward Cr(VI) fitted by Langmuir isotherm model ranged from 3.2 to 1185 mg/g. Mechanisms of complexation, chelation, reduction, electrostatic attraction, anion exchange, and hydrogen bonding were involved in the Cr(VI) removal. Influence factors on Cr(VI) removal were itemized. Polymeric adsorbents performed much better in the strong acidic pH range (e.g., pH 2.0) and at higher initial Cr(VI) concentrations. The adsorption of Cr(VI) was an endothermic reaction, and higher reaction temperature favored more robust adsorption. Anions inhibited the removal of Cr(VI) through competitive adsorption, while that was barely affected by cations. Factors that affected the regeneration of these adsorbents were summarized. To realize the goal of industrial application and environmental protection, removal of the Cr(VI) accompanied by its detoxication through reduction is highly encouraged. Moreover, development of adsorbents with strong regeneration ability and low cost, which are robust for removing Cr(VI) at trace levels and a wider pH range, should also be an eternally immutable subject in the future. Work done will be helpful for developing more robust polymeric adsorbents and for promoting the treatment of Cr(VI)-containing wastewater.

Nanotechnology- A ray of hope for heavy metals removal

Environmental effects of heavy metal pollution are considered as a widespread problem throughout the world, as it jeopardizes human health and also reduces the sustainability of a cleaner environment. Removal of such noxious pollutants from wastewater is pivotal because it provides a propitious solution for a cleaner environment and water scarcity. Adsorption treatment plays a significant role in water remediation due to its potent treatment and low cost of adsorbents. In the last two decades, researchers have been highly focused on the modification of adsorption treatment by functionalized and surface-modified nanomaterials which has spurred intense research. The characteristics of nano adsorbents attract global scientists as it is also economically viable. This review shines its light on the functionalized nanomaterials application for heavy metals removal from wastewater and also highlights the importance of regeneration of nanomaterials in the view of visualizing the economic aspects along with a cleaner environment. The review also focused on the proper disposal of nanomaterials with crucial issues that persist in the adsorption process and also emphasize future research modification at a large-scale application in industries.

Emerging Applications of Versatile Polyaniline-Based Polymers in the Food Industry

Intrinsically conducting polymers (ICPs) have been widely studied in various applications, such as sensors, tissue engineering, drug delivery, and semiconductors. Specifically, polyaniline (PANI) stands out in food industry applications due to its advantageous reversible redox properties, electrical conductivity, and simple modification. The rising concerns about food safety and security have encouraged the development of PANI as an antioxidant, antimicrobial agent, food freshness indicator, and electronic nose. At the same time, it plays an important role in food safety control to ensure the quality of food. This study reviews the emerging applications of PANI in the food industry. It has been found that the versatile applications of PANI allow the advancement of modern active and intelligent food packaging and better food quality monitoring systems.

Kinetic and Isothermal Investigations on the Use of Low Cost Coconut Fiber-Polyaniline Composites for the Removal of Chromium from Wastewater

Pollution due to various heavy metals is increasing at an alarming rate. Removal of hexavalent chromium from the environment is a significant and challenging issue due to its toxic effects on the ecosystem. Development of a low-cost adsorbent with better adsorption efficiency is presently required. In this study, waste coconut fibers (CF) were used to prepare its composite with polyaniline (PANI) via in-situ oxidation. The obtained composites with varying loading of PANI (15, 25, 50, and 75% w/w) were characterized by FE-SEM, TGA, and FTIR spectroscopy. The prepared composites were evaluated for their adsorption performance for removal of Cr(VI). It was concluded that the composite with 50% w/w polyaniline loading on coconut fiber exhibited a maximum adsorption efficiency of 93.11% in 30 min. The effect of pH, dosage, and concentration of the aqueous solution of chromium on the Cr(VI) adsorption efficiency of the composite was also studied. From the optimization studies it was observed that the absorbents exhibited the best adsorption response for Cr(VI) removal with 0.25 mg/mL adsorbent at pH 4, in 30 min. The effect of pH, dosage, and concentration of the aqueous solution of chromium on the Cr(VI) adsorption efficiency of the composite was also studied. This study highlights the application of low-cost adsorbent as a potential candidate for the removal of hexavalent chromium. A detailed study on the adsorption kinetics and isothermal analysis was conducted for the removal of Cr(VI) from aqueous solution using coconut fiber-polyaniline composite. From the kinetic investigation, the adsorption was found to follow the pseudo second order model. The data obtained were best fitted to the Elovich model confirming the chemisorption of the Cr(VI) on coconut polymer composites. The analysis of the isothermal models indicated monolayer adsorption based on the Langmuir adsorption model.

Polyaniline Modified CNTs and Graphene Nanocomposite for Removal of Lead and Zinc Metal Ions: Kinetics, Thermodynamics and Desorption Studies

A novel polyaniline-modified CNT and graphene-based nanocomposite (2.32–7.34 nm) was prepared and characterized by spectroscopic methods. The specific surface area was 176 m²/g with 0.232 cm³/g as the specific pore volume. The nanocomposite was used to remove zinc and lead metal ions from water; showing a high removal capacity of 346 and 581 mg/g at pH 6.5. The data followed pseudo-second-order, intraparticle diffusion and Elovich models. Besides this, the experimental values obeyed Langmuir and Temkin isotherms. The results confirmed that the removal of lead and zinc ions occurred in a mixed mode, that is, diffusion absorption and ion exchange between the heterogeneous surface of the sorbent containing active adsorption centers and the solution containing metal ions. The enthalpy values were 149.9 and 158.6 J.mol⁻¹K⁻¹ for zinc and lead metal ions. The negative values of free energies were in the range of −4.97 to −26.3 kJ/mol. These values indicated an endothermic spontaneous removal of metal ions from water. The reported method is useful to remove the zinc and lead metal ions in any water body due to the high removal capacity of nanocomposite at natural pH of 6.5. Moreover, a low dose of 0.005 g per 30 mL made this method economical. Furthermore, a low contact time of 15 min made this method applicable to the removal of the reported metal ions from water in a short time. Briefly, the reported method is highly economical, nature-friendly and fast and can be used to remove the reported metal ions from any water resource.

Spray-Assisted Interfacial Polymerization to Form CuII/I@CMC-PANI Film: An Efficient Dip Catalyst for A3 Reaction

A novel and interesting method for the preparation of carboxymethylcellulose–polyaniline film-supported copper catalyst (Cu^II/I@CMC-PANI) has been developed via spray-assisted interfacial polymerization. Using copper sulfate as an initiator, spraying technology was introduced to form a unique interface that is perfectly beneficial to the polymerization of aniline monomers onto carboxymethylcellulose macromolecule chains. To further confirm the composition and structure of the as-prepared hybrid film, it was systematically characterized by inductively coupled plasma (ICP), Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and thermogravimetric analysis (TGA) techniques. The Cu content in the fresh Cu^II/I@CMC-PANI film was determined to be 1.805 mmol/g, and spherical nanoparticles with an average size of ca. 10.04 nm could be observed in the hybrid film. The Cu^II/I@CMC-PANI hybrid film was exerted as a dip catalyst to catalyze the aldehyde–alkyne–amine (A³) coupling reactions. High yields of the products (up to 97%) were obtained in this catalytic system, and the catalyst could be easily picked up from the reaction mixture by tweezers and reused for at least six consecutive runs, without any discernible losses in its activity in the model reaction. The dip catalyst of Cu^II/I@CMC-PANI, with easy fabrication, convenient deployment, superior catalytic activity, and great reusability, is expected to be very useful in organic synthesis.

Synthesis and characterization of poly (styrene-co-acrylamide)-graft-polyanilines as new sorbents for mercuric present in aqueous hydrocarbon liquids

Background

The unprocessing hydrocarbon oil often contains high concentrations of mercury, which damages the metallic processing components and have health risk on workers and environment. Mercuric removal unit associated with natural gas processing plant is failed to complete mercury removal and then mercury distributed in most places of removal unit. Most of unremoved mercury are found in polar solutions.

Results

Styrene-co-acrylamide-graft-polyanilines were synthesized and characterized. The copolymer formed by free radical emulsion copolymerization of styrene-acrylamide (14:1) using ammonium persulphate (APS) at 60 °C. In addition, the grafting process was also achieved by oxidation chemical polymerization of the above copolymer with both aniline and 2-chloroaniline using APS. The synthetic polymeric samples were characterized using infrared (IR), x-ray diffraction (XRD), scan electron microscope (SEM), transition electron microscope (TEM), thermogravimetric analysis (TGA) and Brunauer–Emmett–Teller (BET) to confirm the polymerization process and investigate the polymeric samples as new sorbents for Hg (II). Both adsorption kinetics and isotherm models were checked.

Conclusions

In most cases Hg (II) was adsorbed as multi-layer on the obtained mesopores materials. The grafting process enhances the copolymer activity towards Hg (II) removal. The complete removal of mercury from water solution portion of mercuric removal unit was achieved by introduction of synthetic polymeric mesopores material based on styrene-co-acrylamide-graft-polyanilines. The removal efficiency closed to 100% in case of grafting with poly (2-chloroaniline).

Sustainable and efficient technologies for removal and recovery of toxic and valuable metals from wastewater: Recent progress, challenges, and future perspectives

Due to their numerous effects on human health and the natural environment, water contamination with heavy metals and metalloids, caused by their extensive use in various technologies and industrial applications, continues to be a huge ecological issue that needs to be urgently tackled. Additionally, within the circular economy management framework, the recovery and recycling of metals-based waste as high value-added products (VAPs) is of great interest, owing to their high cost and the continuous depletion of their reserves and natural sources. This paper reviews the state-of-the-art technologies developed for the removal and recovery of metal pollutants from wastewater by providing an in-depth understanding of their remediation mechanisms, while analyzing and critically discussing the recent key advances regarding these treatment methods, their practical implementation and integration, as well as evaluating their advantages and remaining limitations. Herein, various treatment techniques are covered, including adsorption, reduction/oxidation, ion exchange, membrane separation technologies, solvents extraction, chemical precipitation/co-precipitation, coagulation-flocculation, flotation, and bioremediation. A particular emphasis is placed on full recovery of the captured metal pollutants in various reusable forms as metal-based VAPs, mainly as solid precipitates, which is a powerful tool that offers substantial enhancement of the remediation processes' sustainability and cost-effectiveness. At the end, we have identified some prospective research directions for future work on this topic, while presenting some recommendations that can promote sustainability and economic feasibility of the existing treatment technologies.

Doped-polyaniline based sorbents for the simultaneous removal of heavy metals and dyes from water: Unravelling the role of synthesis method and doping agent

Recently, the engineering of alternative adsorbents with better functional and sorbing ability towards the purification of wastewaters has received much attention from the scientific community. Currently polymers, in particular, are regarded as attractive soft materials in the field of environmental remediation due to their several unique properties. In this regard, the synthesis method is key point to fabricate polymer-based adsorbent with targeted characteristics. In the present work, four polyaniline (PANIs) samples were synthesized by two alternative chemical approaches, a traditional one and an eco-friendly one, and two different dopants were used, HCl and H₂SO_4, respectively. All PANIs were characterized for their thermal, optical, morphological, and structural properties and their capability to remove simultaneously dyes and heavy metals from water have been investigated. It was deduced that the sorption ability is dependent on the as-synthesized PANI using different procedures and dopants. All the PANIs from traditional method showed high levels of pollutants removal (from 89 to 97%). Even though the materials obtained from the green way are overall less active, H₂SO₄-doped corresponding polymer showed high sorption capability (75-97%). Finally, the most performing PANIs were selected for recycling tests exhibiting high sorption efficiency retention up to four runs without any regeneration treatment. Most important, the cycling tests were stopped well before the sample sorption limit could be reached.

Linear and star-shaped π-conjugated oligoanilines: a review on molecular design in syntheses and properties

Molecular Design and Synthesis of Linear and Star-shaped π-conjugated Oligoanilines with reversible optoelectrochemical properties.

The Adsorption Performance of Polyaniline/ZnO Synthesized through a Two-Step Method

Polyaniline/Zinc oxide (PANI/ZnO) were prepared using a two-step method, and the morphology and the structure of PANI/ZnO composites were characterized through a scanning electron microscope (SEM) and X-ray diffraction (XRD). Factors such as the content of ZnO, the adsorption time and the mass of the adsorbent, and the kinetic equation of PANI/ZnO as adsorbents for the adsorption of methyl orange solution were studied. The results showed that the adsorption efficiency of methyl orange by polyaniline with the increase of adsorbent mass firstly increased and then decreased. Among the composites with the same quality, PANI composites with 8% ZnO have a better adsorption effect for methyl orange, and the maximum adsorption ratio can reach 69% with the increase of adsorption time at 0.033 g; With the increase of adsorbent mass, the adsorption efficiency of PANI composites with 8% ZnO increased continuously. When the mass increased from 0.033 g to 0.132 g, the adsorption rate increased from 69% to 93%, and the adsorption of the methyl orange solution by PANI/ZnO composites was more in line with the quasi-second-order kinetic equation.

Application of co-pyrolysis biochar for the adsorption and immobilization of heavy metals in contaminated environmental substrates

Heavy metal pollution has been considered as a serious threat to the environment and human in the past decades due to its toxic and unbiodegradable properties. Recently, extensive studies have been carried out on the removal of heavy metals, and various adsorption materials have been successfully developed. Among, biochar is a promising option because of its advantages of various biomass sources, abundant microporous channels and surface functional groups, as well as its attractive economic feasibility. However, the application of pristine biochar is limited by its low adsorption capacity and nonregenerative property. Co-pyrolysis biochar, produced from the pyrolysis of biomass with the addition of another biomass or non-biomass precursor, is potential in overcoming the limitation of pristine biochar and achieving superior performance for heavy metal adsorption and immobilization. Therefore, this article summarizes the recent advances in development and applications of co-pyrolysis biochar for adsorption and immobilization of various heavy metals in contaminated environmental substrates. In details, the production, characteristics and advantages of co-pyrolysis biochar are initially presented. Subsequently, the adsorption behaviors and mechanisms of different heavy metals (including Hg, Zn, Pb, Cu, Cd, Cr, As, etc.) in flue gas and wastewater by co-pyrolysis biochar are reviewed, as well as factors influencing their adsorption capacities. Meanwhile, the immobilization of heavy metals in both biochar itself and contaminated soils by co-pyrolysis biochar is discussed. Finally, the limitations of current studies and future prospects are proposed. It aims at providing a guideline for the exploitation and application of cost-effective and environmental-friendly co-pyrolysis biochar in the decontamination of environmental substrates.

Bioinspired Neuron-like Adsorptive Networks for Heavy Metal Capture and Tunable Electrochemically Mediated Recovery

Electrochemical techniques have garnered increasing attention as a heavy metal remediation platform for pollutant mitigation and sustainable recycling. Inspired by the biological signal-transfer mode, biomimic neuron-like hierarchical adsorptive networks were constructed by interweaving one-dimensional manganese oxide nanowires into polyaniline-decorated hollow structural metal-organic frameworks (MOFs). The prepared biomimic neuron adsorbent exhibits good adsorption capacity toward cations (Pb²⁺) and oxyanions (Cr₂O₇^2-) at the neutral state; tunable cation/oxyanion desorption can be electrochemically switched at the oxidized and reduced states, respectively, where the biomimic neuron-like hierarchical adsorptive networks facilitated electron transfer and benefited substantial redox reactions. The combination of simulations and calculations demonstrates that the curvature-induced polarization in a hollow MOF structure enhances the desorption efficiencies by improving the redox processes at the electrode-electrolyte interface, which facilitate the promising implementation in terms of water economy and downstream waste sustainability.

Highly efficient removal of Sb(V) from water by franklinite-containing nano-FeZn composites

The existence of toxic and carcinogenic pentavalent antimony in water is a great safety problem. In order to remove antimony(V) from water, the purpose of this study was to prepare a novel graphene nano iron zinc (rGO/NZV-FeZn) photocatalyst via hydrothermal method followed by ultrasonication. Herein, weakly magnetic nano-Fe–Zn materials (NZV-FeZn, GAC^SP/NZV-FeZn, and rGO/NZV-FeZn) capable of rapid and efficient Sb(V) adsorption from water were prepared and characterised. In particular, rGO/NZV-FeZn was shown to comprise franklinite, Fe⁰, and graphite. Adsorption data were fitted by a quasi-second-order kinetic equation and Langmuir model, revealing that among these materials, NZV-FeZn exhibited the best Sb removal performance (543.9 mg_Sb g_NZV-FeZn⁻¹, R² = 0.951). In a practical decontamination test, Sb removal efficiency of 99.38% was obtained for a reaction column filled with 3.5 g of rGO/NZV-FeZn. Column regenerability was tested at an initial concentration of 0.8111 mg_Sb L⁻¹, and the treated water obtained after five consecutive runs complied with the GB5749-2006 requirement for Sb. rGO/NZV-FeZn was suggested to remove Sb(V) through adsorption-photocatalytic reduction and flocculation sedimentation mechanisms and, in view of its high cost performance, stability, and upscalable synthesis, was concluded to hold great promise for source water and wastewater treatment.

Carbon Nanostructures Derived through Hypergolic Reaction of Conductive Polymers with Fuming Nitric Acid at Ambient Conditions

Hypergolic systems rely on organic fuel and a powerful oxidizer that spontaneously ignites upon contact without any external ignition source. Although their main utilization pertains to rocket fuels and propellants, it is only recently that hypergolics has been established from our group as a new general method for the synthesis of different morphologies of carbon nanostructures depending on the hypergolic pair (organic fuel-oxidizer). In search of new pairs, the hypergolic mixture described here contains polyaniline as the organic source of carbon and fuming nitric acid as strong oxidizer. Specifically, the two reagents react rapidly and spontaneously upon contact at ambient conditions to afford carbon nanosheets. Further liquid-phase exfoliation of the nanosheets in dimethylformamide results in dispersed single layers exhibiting strong Tyndall effect. The method can be extended to other conductive polymers, such as polythiophene and polypyrrole, leading to the formation of different type carbon nanostructures (e.g., photolumincent carbon dots). Apart from being a new synthesis pathway towards carbon nanomaterials and a new type of reaction for conductive polymers, the present hypergolic pairs also provide a novel set of rocket bipropellants based on conductive polymers.

Electrically conductive biocompatible composite aerogel based on nanofibrillated template of bacterial cellulose/polyaniline/nano-clay

Bacterial cellulose (BC) aerogel owing to its porous and 3D structure, poses a suitable matrix for embedding nanomaterials and polymers. Herein, BC composites comprising nano-clay/polyaniline (PANI) were synthesized via a two-step procedure. Clay nanoplatelets were dispersed in the BC membrane to form a nanofibrillated template for aniline in-situ polymerization leading to formation of a double interconnected network of electrically conductive path within the aerogel. Deposition of PANI particles on BC/clay nanocomposite was confirmed by FTIR, XRD, FESEM, and EDX techniques. The surface electrical conductivity of 0.49 S/cm was obtained for the composite aerogel comprising 5 wt% nano-clay which is 16 folds higher than that of the sample without nano-clay. Thermal stability and storage modulus of the aerogels was improved by inclusion of PANI and nano-clay. Synergistic effect of clay and polyaniline on biocompatibility and cell adhesion was obtained with no mutagenic or carcinogenic effects. The developed electrically conductive composite aerogels can be utilized as suitable scaffolds for tissue engineering applications demanding a good balance of flexibility, dimensional and thermal stability and biocompatibility.