High-efficiency and selective adsorption of organic pollutants by magnetic CoFe2O4/graphene oxide adsorbents: Experimental and molecular dynamics simulation study

Abatement of methylene blue and diazinon pesticide from synthetic solutions using magnetic biochar from pistachio shells modified with MOF-808

This study develops a magnetic composite from pistachio shell biochar (PSBC/CoFe₂O₄) modified with MOF-808 for removing methylene blue (MB) dye and diazinon (DA) pesticide from water. The composite, with a surface area of 151.53 m2/g and magnetic saturation of 19.653 emu/g, allowed easy separation from solutions. Key adsorption factors such as pH, temperature, contact time, adsorbent dosage, and initial pollutant concentration were optimized. Maximum removal efficiencies of 99.32% for MB and 99.14% for DA were achieved at adsorbent dosages of 1 g/L for MB and 1.5 g/L for DA, initial concentrations of 5 mg/L, temperatures of 55 °C, contact times of 60 min for MB and 80 min for DA, and pH levels of 9 for MB and 6 for DA. Thermodynamic analysis confirmed that the adsorption process is spontaneous and endothermic, with enthalpy values of 55.091 kJ/mol for MB and 42.028 kJ/mol for DA, while entropy values indicated increased randomness during adsorption. Kinetic studies revealed that adsorption involved both physical and chemical interactions, with intraparticle diffusion not being the rate-limiting step. The Freundlich isotherm model provided the best fit (R2 = 0.971 for MB and 0.988 for DA), highlighting heterogeneous surface interactions. The composite showed higher adsorption capacities for MB (31.44 mg/g) than for DA (21.49 mg/g) and exhibited excellent regeneration potential, performing better in deionized water due to the inhibitory effects of salts in non-deionized water.

Electrochemical and quantum chemical investigation on the adsorption behavior of a schiff base and its metal complex for corrosion protection of mild steel in 15 wt% HCl solution

This work evaluates the effectiveness of Schiff base derivatives, namely, 2,2'-((1E,1'E)-((2,2-dimethylpropane-1,3-diyl)bis(azaneylylidene))bis(methaneylylidene))diphenol (DAMD) and (2-((E)-((3-(((E)-2-hydroxybenzylidene)amino)-2,2dimethylpropyl)imino)methyl)phenoxy) zinc (HDMZ), as corrosion inhibitors for mild steel in a 15 % HCl solution. By employing a blend of experimental assessments and theoretical computations, such as electrochemical tests, morphological observations, and theoretical simulations, the study achieved an impressive up to 94.6 % inhibition efficiency. Notably, HDMZ exhibited significant protective properties. The results of PDP showed that both inhibitors act as mixed-type corrosion inhibitors. SEM surface analysis of the uninhibited and inhibited samples revealed the formation of a protective layer of inhibitor molecules on the mild steel surface to mitigate its corrosion. The Langmuir adsorption model verified the occurrence of dual adsorption, while theoretical simulations offered insights into the underlying interaction mechanisms. The identification of Schiff-based inhibitors reveals a pronounced synergistic effect in corrosion inhibition, marking a significant advancement in understanding corrosion control mechanisms. This study illuminates the process of forming covalent bonds between inhibitor molecules and iron atoms, presenting a hopeful path towards the advancement of corrosion inhibitors tailored for industrial use. The parallel adsorption configuration and mutual interactions form a stable structure, reinforcing the organic-metal bonds and enhancing both chemical and physical adhesion to the steel surface. These findings indicate that the synergistic effect of molecular interactions and polar-rich regions offers a promising strategy for designing functional hybrid materials.

Experiment and Simulation Study on the Adsorption Interaction between a Fluorescent Tracer and a Montmorillonite Crystal in Drilling Fluid

The adsorption interaction of oil field tracer in drilling fluid plays a significant role in tracer monitoring (TM) technology in the petroleum industry. In this work, the adsorption performances of Rhodamine B (RhB+) and fluorescein sodium (Fln-) tracers with montmorillonite (MMT) crystal in drilling fluid were investigated by both experimental and simulation methods. For the experimental aspect, the macroscopic results indicate thermodynamic monolayer adsorption by the Langmuir model and kinetic chemical adsorption by the pseudo-second-order (PSO) model. As a result, MMT shows a larger adsorption capacity (qm) for RhB+ than for Fln- with q m ( RhB + ) = 0.069 ⁡ g ⁡ g - 1 > q m ( Fln - ) = 0.016 g ⁡ g - 1 but stronger adsorption spontaneity (ΔrGmθ) for Fln- than for RhB+ with Δ r G m θ ( Fln - ) = - 7.92 kJ mol-1 < Δ r G m θ ( RhB + ) = - 6.90 kJ mol-1. Meanwhile, the interaction rate (k2) of Fln- was shown to be faster than that of RhB+ with k 2 ( Fln - ) = 1.07 ⁡ min - 1 ⁡ > k 2 ( RhB + ) = 0.95 ⁡ min - 1 ⁡ . For simulation insight, MMT shows much higher system stability (E) for Fln- than for RhB+ with E Fln - · · · MMT < E RhB + · · · MMT and Δ E Fln - · · · MMT > Δ E RhB + · · · MMT . Meanwhile, the microscopic simulation results reveal configuration changes and site distinctions for RhB+ and Fln- interactions with the MMT crystal. The different adsorption responses were explained by proposing an interaction mechanism of force dominance and position orientation. Specifically, Fln- was deduced to interact with metal (Al, Ca) and metalloid (Si) elements in the MMT crystal interlayer by "upright-insertion" orientation while RhB+ was deduced to interact with oxygen atoms on the MMT crystal surface by a "flat-lying" orientation. Hydrogen bonds, the electrostatic interaction, and the coordination effect were revealed to dominate for the interaction of tracer adsorption. This work provides both performance and mechanism investigation of fluorescent tracer adsorption interaction with the MMT crystal in drilling fluid, which is of great significance in reservoir exploitation.

Density Functional Theory analysis and molecular dynamic simulation to understand the mechanism of hazardous dyes adsorption onto cellulose in aqueous solution

This work examines the use of cellulose in the elimination of anionic dye, indigo carmine and methyl red, from aqueous media. Theoretical analyses revealed that the examined compounds had several reactive sites that encouraged dyes to adhere to the cellulose surface, and molecular dynamics simulations demonstrated that this adsorption occurred flat-lying on the cellulose (200) surface. However, it has been discovered that the reactivity of individual molecules is limited in its ability to foretell the effectiveness and characteristics of compound adsorption on cellulose. The capacity to model dye adsorption on polymeric surfaces in the presence of a simulated aqueous solution is one of the key benefits of molecular dynamics modeling, and it can reveal valuable information regarding the selected molecules' adsorption configuration and its competitiveness. Both dyes exhibit high adsorption on the cellulose adsorbent, indicating that chemical bonds play a major role in the adsorption capacity of the dyes. The order of adsorption energy indicates a clear selective adsorption tendency. The radial distribution function analysis shows that both dyes are chemisorbed at the cellulose surface. Quantum and dynamic descriptors have validated the experimental results in the literature. This offers valuable insights into the adsorption mechanism of anionic dyes on cellulose.

Molecular simulation-based insights into dye pollutant adsorption: A perspective review

Growing concerns about environmental pollution have highlighted the need for efficient and sustainable methods to remove dye contamination from various ecosystems. In this context, computational methods such as molecular dynamics (MD), Monte Carlo (MC) simulations, quantum mechanics (QM) calculations, and machine learning (ML) methods are powerful tools used to study and predict the adsorption processes of dyes on various adsorbents. These methods provide detailed insights into the molecular interactions and mechanisms involved, which can be crucial for designing efficient adsorption systems. MD simulations, detailing molecular arrangements, predict dyes' adsorption behaviour and interaction energies with adsorbents. They simulate the entire adsorption process, including surface diffusion, solvent layer penetration, and physisorption. QM calculations, especially density functional theory (DFT), determine molecular structures and reactivity descriptors, aiding in understanding adsorption mechanisms. They identify stable adsorption configurations and interactions like hydrogen bonding and electrostatic forces. MC simulations predict equilibrium properties and adsorption energies by sampling molecular configurations. ML methods have proven highly effective in predicting and optimizing dye adsorption processes. These models offer significant advantages over traditional methods, including higher accuracy and the ability to handle complex datasets. These methods optimize adsorption conditions, clarify adsorbent functionalization roles, and predict dye removal efficiency under various conditions. This research explores MD, MC, QM, and ML approaches to connect molecular interactions with macroscopic adsorption phenomena. Probing these techniques provides insights into the dynamics and energetics of dye pollutants on adsorption surfaces. The findings will aid in developing and optimizing new materials for dye removal. This review has significant implications for environmental remediation, offering a comprehensive understanding of adsorption at various scales. Merging microscopic data with macroscopic observations enhances knowledge of dye pollutant adsorption, laying the groundwork for efficient, sustainable removal technologies. Addressing the growing challenges of ecosystem protection, this study contributes to a cleaner, more sustainable future.

Microporous Cobalt Ferrite with Bio-Carbon Loosely Decorated to Construct Multi-Functional Composite for Dye Adsorption, Anti-Bacteria and Electromagnetic Protection

Currently, facing electromagnetic protection requirement under complex aqueous environments, the bacterial reproduction and organic dye corrosion may affect the composition and micro-structures of absorbers to weaken their electromagnetic properties. To address such problems, herein, a series of CoFe2O4@BCNPs (cobalt ferrite @ bio-carbon nanoparticles) composites are synthesized via co-hydrothermal and calcining process. The coupling of magnetic cobalt ferrite and dielectric bio-carbon derived from Apium can endow the composite multiple absorption mechanisms and matched impedance for effective microwave absorption, attaining a bandwidth of 8.12 GHz at 2.36 mm and an intensity of -49.85 dB at 3.0 mm. Due to the ROS (reactive oxygen species) stimulation ability and heavy metal ions of cobalt ferrite, the composite realizes an excellent antibacterial efficiency of 99% against Gram negative bacteria of Escherichia coli. Moreover, the loose porous layer of surface stacked bio-carbon can promote the adsorption of methylene blue for subsequent eliminating, a high removal rate of 90.37% for organic dye can be also achieved. This paper offers a new insight for rational design of composite's component and micro-structure to construct multi-functional microwave absorber for satisfying the electromagnetic protection demand in complicated environments.

Enhancing adsorption capacity of carbon nanotubes through sand filters for the removal of organic pollutants: a column investigation

Dissolved organic pollutants caused by paints, detergents, herbicides, and toxins cannot be removed by conventional water treatment processes such as filtration. Different figures of activated carbon such as carbon nanotubes (CNTs) are substances to obliterate these contaminants. Although these CNTs have higher ability to decompose organic contaminants, using the slurry form of CNTs is not suitable due to the removal requirement at the end of the treatment procedure. In this study, upgraded CNTs attached to particles of sand filters (CNTsand) were synthesised and applied to remove dissolved organic pollutants. The results revealed the high capacity of the CNTsand to extract organic contaminants. The column test with natural water compared to the distilled water had a more extended breakpoint, higher adsorption capacity, and consequently, further removal efficiency, such that for the surface area loading rate of 4.8 ml/min, the breakpoint increased from 739 minutes to 936 minutes as well as the volume of passed water grew from 3546 ml to 4493 ml; Therefore, the maximum adsorption capacity was enhanced from 67.3 mg/g to 89.5 mg/g. In conclusion, the adequacy and efficiency of the upgraded nanotube coating on sand grains to remove organic pollutants were confirmed.

Design and preparation of a novel Mg-Al LDH@EDTA-Melamine nanocomposite for effective adsorptive removal of methylene blue and rhodamine B dyes from water

This paper deals with the preparation of a novel nanocomposite consisted of magnesium-aluminum layered double hydroxide (Mg-Al LDH) and ethylenediaminetetraacetic acid (EDTA) as well as melamine (MA) as an adsorbent. This nanocomposite was utilized to adsorb different dyes such as rhodamine B (RhB) and methylene blue (MB) from water. The prepared adsorbent was characterized using FT-IR, EDS, XRD, TGA, and FE-SEM analyses. The effects of various parameters such as concentration, time, adsorbent dosage, temperature, and pH were tested to investigate their influence on adsorption conditions. Both methylene blue and rhodamine B dyes showed pseudo-second-order adsorption kinetics, and their adsorption followed the Langmuir isotherm. Moreover, the maximum adsorption capacities for methylene blue and rhodamine B were found to be 1111.103 mg/g at 45 °C and 232.558 mg/g at 60 °C, respectively. Additionally, the adsorption processes were found to be spontaneous (ΔG°< 0, for both dyes) and exothermic (ΔH° = -12.42 kJ/mol for methylene blue and ΔH° = -25.84 kJ/mol for rhodamine B) for both dyes. Hydrogen bonding and electrostatic forces are responsible for the interactions occur between the nanocomposite and the functional groups in the dyes. The experimental findings demonstrated a greater adsorption rate of MB than RhB, suggesting the adsorbent's stronger affinity for MB. This preference is likely due to MB's size, specific functional groups, and smaller molecule size, enabling stronger interactions and more efficient access to adsorption sites compared to RhB. Even after recycling 4 times, the dye adsorption percentages of the adsorbent for MB and RhB dyes were 90 % and 87 %, but the desorption percentages of the adsorbate dyes were 85 % and 80 %, respectively. The prepared adsorbent boasts several unique properties, such as the swift and effortless adsorption of MB and RhB dyes, straightforward synthesis, mild adsorption conditions, remarkable efficiency, and the ability to be recycled up to 4 times without a significant decrease in activity.

A graphene oxide based composite granule for methylene blue separation from aqueous solution: Adsorption, kinetics and thermodynamic studies

Graphene oxide and chitosan composite material using as a high-efficiency and low-cost granular adsorbent for methylene blue removal was fabricated via self-assembling method. The effects of pH value, contact time, initial concentration, adsorbent dose, temperature, and recyclic stability on the adsorption performance of methylene blue in aqueous solution were investigated in detail. Desorption process with the effects of solvents, contact time, and temperature were also conducted carefully in this study. The adsorption kinetics and adsorption isotherm of dye adsorption process showed that dye adsorption process was fitted to the pseudo-second-order kinetic model and the Freundlich adsorption isotherm, indicating a physical adsorption process with multilayer adsorption. The intra-particle diffusion model indicated that the dye adsorption by the granular adsorbent was strongly happened during the first 4 h. The thermodynamic study showed that the adsorption was a spontaneous and exothermic process and dye ions were condensed onto the surface of adsorbent. The maximum adsorption capacity of dye on the granular adsorbent was calculated as 951.35 mg/g and the adsorbent could maintain its adsorption performance after six cycles. In general, this study provided an efficient, cost-effective, and recyclable the granular adsorbent for dye separation from aqueous solution.

Molecular level investigation of interactions between pharmaceuticals and β-cyclodextrin (β-CD) functionalized adsorption sites for removal of pharmaceutical contaminants from water

This study describes a novel application of the use of molecular modeling tools for investigating the adsorption of organic micropollutants (OMPs) from water by nanocomposites. The partitioning of pharmaceuticals onto β-Cyclodextrin (β-CD) functionalized adsorbents was investigated at the molecular level to explore the atomistic interactions of pharmaceutical contaminants in water systems with β-CD and to provide insight into possible approaches for removal of pharmaceuticals from water. Molecular electrostatic surface potential mapping of β-CD derivatives was employed to examine the impact of substitution degree of β-CD and type of grafting agent on host-guest complexation. The stability of the complexes of selected pharmaceuticals and β-CD derivatives were assessed via molecular dynamics simulations to evaluate competitive adsorption between organic micropollutants (OMPs) and between OMPs and fulvic acid, a representative natural organic material (NOM) component found in water systems. Molecular electrostatic surface potential maps showed that grafting agents with aromatic and amine functional groups were found to provide attractive interactions for negatively charged OMPs. In addition, optimization of substitution degree of β-CD is necessary to enhance adsorption of target OMPs. Furthermore, it was found that aromatic ring bearing grafting agents can provide additional electrostatic attractions by π-π interactions with the aromatic ring of the OMPs. The impact of common water quality characteristics on adsorption was assessed and it was revealed that the effect of pH and calcium on adsorption depends on the ionizable functional groups present on the grafting agent. Molecular dynamics simulations showed that adsorption of target OMPs does not solely depend on hydrophobicity but is affected by electrostatic interactions. The simulations revealed that fulvic acid which is commonly present in environmental waters can be a competitor with ibuprofen for the β-CD cavity. Ultimately, this study showed that molecular level simulation can be effectively employed to investigate adsorption of OMPs by β-CD functionalized adsorbents and could be employed to enhance their design and subsequent environmental applications.

From Waste to Resource: Valorization of Lignocellulosic Agri-Food Residues through Engineered Hydrochar and Biochar for Environmental and Clean Energy Applications-A Comprehensive Review

Agri-food residues or by-products have increased their contribution to the global tally of unsustainably generated waste. These residues, characterized by their inherent physicochemical properties and rich in lignocellulosic composition, are progressively being recognized as valuable products that align with the principles of zero waste and circular economy advocated for by different government entities. Consequently, they are utilized as raw materials in other industrial sectors, such as the notable case of environmental remediation. This review highlights the substantial potential of thermochemical valorized agri-food residues, transformed into biochar and hydrochar, as versatile adsorbents in wastewater treatment and as promising alternatives in various environmental and energy-related applications. These materials, with their enhanced properties achieved through tailored engineering techniques, offer competent solutions with cost-effective and satisfactory results in applications in various environmental contexts such as removing pollutants from wastewater or green energy generation. This sustainable approach not only addresses environmental concerns but also paves the way for a more eco-friendly and resource-efficient future, making it an exciting prospect for diverse applications.

Selective adsorption and separation of methylene blue by facily preparable xanthan gum/amantadine composites

In this work, xanthan gum-based composites were successfully graft-modified by amantadine (XG-Fe³⁺/AM) with higher adsorption capacity and selectivity on recycling cationic dye (methylene blue, MB) from aqueous solution. The adsorption equilibrium of MB could be achieved approximately within 5 min when the initial concentration was 100 mg/L, and the maximum adsorption capacity was up to 565 mg/g. After 5 desorption-regeneration cycles, the removal rate of XG-Fe³⁺/AM for MB could still be as high as 95 % with slight decrement. Additionally, the effects of pH, contact time, temperature and initial dye concentration on the adsorption performance of MB were systematically examined. Furthermore, the adsorbent was characterized by FT-IR, BET and XPS analysis. In mixed anionic and cationic dyes, the adsorption selectivity of XG-Fe³⁺/AM on MB in the mixture of MB and methyl orange (MO) reached up to 99.69 %. Molecular dynamics simulation revealed that the trend of adsorption energy for dyes was in good agreement of the experimental order of adsorption capacities and molecular sizes among seven anionic and cationic dyes based on molecular matching effect and electrostatic interaction. Therefore, XG-Fe³⁺/AM is an eco-friendly, facile-synthesis and high-selectivity adsorbent, which remove cationic dyes in multi-component systems through electrostatic interaction and molecular matching effect.

Tunable sulphur doping on CuFe2O4 nanostructures for the selective elimination of organic dyes from water

In this work, sulphur doped copper ferrites (S-CuFe2O4) photocatalysts were successfully synthesized for the first time using the facile hydrothermal method. The as-synthesized photocatalysts were characterized through XRD, Raman, TGA, FT-IR, UV-Vis-DRS, SEM, EDX and PL techniques. The results revealed that doping with sulphur has been found to be a suitable alternative that causes strain in the lattices as anions replace the oxygen from the CuFe2O4 nanostructures. Due to sulphur dopants, photocatalysts are able to efficiently trap and transfer the photoinduced charges, which readily suppress charge recombination. A UV-Vis spectrophotometer was used to monitor the degradation of selective toxic organic dyes (RhB, CR, MO, and CV) in aqueous media. The dye degradation results provide evidence for the surprisingly superior performance of S-CuFe2O4 over pristine CuFe2O4. On the basis of its efficiencies, this work can be assigned as an excellent candidate for photocatalysis science.

Hydrogen Bonding Principle-Based Molecular Design of a Polymer Excipient and Impacts on Hydrophobic Drug Properties: Molecular Simulation and Experiment

Although some commercial excipients for improving the solubility of highly crystalline drugs are widely used, they still cannot cover all types of hydrophobic drugs. In this regard, with phenytoin as the target drug, related molecular structures of polymer excipients were designed. The optimal repeating units of NiPAm and HEAm were screened out through quantum mechanical simulation and Monte Carlo simulation methods, and the copolymerization ratio was also determined. Using molecular dynamics simulation technology, it was confirmed that the dispersibility and intermolecular hydrogen bonds of phenytoin in the designed copolymer were better than those in the commercial PVP materials. At the same time, the designed copolymers and solid dispersions were also prepared during the experiment, and the improvement of their solubility was confirmed, which is in accordance with the simulation predictions. The new ideas and simulation technology may be used for drug modification and development.

Investigation of Oil-Water Separation on an F-SiO2/TiO2-Based Superhydrophobic/Superoleophilic Surface: Experiment Evaluation and MD Simulation

Experiment evaluation and mechanism analysis of separation performance are crucial for oily wastewater treatment. In this work, a fluorinated superhydrophobic/superoleophilic (F-SHPB/SOPL) surface was fabricated on a steel mesh substrate by double depositions of SiO₂-TiO₂ nanoparticles for high-roughness improvement and composite modification of fluorine-alkyl groups for low-energy achievement. Measurements of SEM, XPS, FTIR, laser scanning confocal microscope (LSCM), and excitation-emission matrix (EEM) were carried out for surface property characterization. The oil-water separation performances at the prepared F-SHPB/SOPL surface were investigated from experimental and simulation aspects. Separation tests, flux tests, and anti-contamination tests were performed by experimental methods. The results indicated that the surface showed excellent separation efficiencies (>99.2%) for oil-water mixture and oil-in-water emulsion, high permeate flux (>3000 L·m^-2·h^-1) for organic oils, and perfect anti-pollution/self-cleaning capacity for liquid and solid contaminations. The interaction energies and interaction distances were measured by ab initio molecular dynamics simulation (AIMD) simulations. With lower interaction energy (E_oil = -456.52∼-1044.22 eV) than that of water molecules (E_water = -172.73 eV) and shorter distance (D_oil = 4.42∼5.13 Å) than that of water molecules (D_water = 11.49 Å), oil molecules showed higher interaction stability than water molecules on the F-SHPB/SOPL surface. The calculation revealed the essence of the oil-water separation phenomenon. This work not only proposes the fabrication methodology of the SHPB/SOPL material but also elucidates the intermolecular interaction for oil-water separation. The results can provide a fundamental basis for separation operation and removal treatment in industrial and domestic applications.

High-efficiency adsorption removal of CR and MG dyes using AlOOH fibers embedded with porous CoFe2O4 nanoparticles

Owing to the toxicity and difficulty in degradation, how to the effective separation for the residual dyes in the aqueous solution is still an issue with great challenge in the area of environmental protection. Now, to high-efficiency removal of organic dyes from the aqueous solution, we design a unique AlOOH/CoFe₂O₄ adsorbent with porous CoFe₂O₄ nanoparticles embedded on the AlOOH fibers using a simple hydrothermal technique and calcination process. The structural properties and surface characteristics of the AlOOH/CoFe₂O₄ composites are detailedly analyzed by XRD, FTIR, XPS, TEM and SEM. Here, the high S_BET and specific porous structure are beneficial to improve the adsorption performance of AlOOH/CoFe₂O₄ adsorbents. Especially, when the molar ratio of AlOOH to CoFe₂O₄ in the AlOOH/CoFe₂O₄ fibers is 1:1, an optimal performance on adsorbing anionic Congo red (CR) and cationic methyl green (MG) dyes can be obtained at pH = 6.29, where the corresponding maximum adsorption capacities reach up to 565.0 and 423.7 mg g^-1, respectively. Factors leading to the change in the ability of adsorbing CR and MG dyes are systematically discussed, including contact time, temperature, initial concentrations, and pH values of the solutions. Meanwhile, the uptake of CR and MG dyes can best conform to Langmuir isotherm model and pseudo-second-order adsorption kinetics. The thermodynamic analysis verifies that the dye adsorption process is spontaneous and endothermic. Moreover, from the point view of practical application, the good reusability further makes the as-synthesized magnetic AlOOH/CoFe₂O₄ composite be a perfect adsorbent with efficiently removing both anionic and cationic dyes from aqueous solutions.

Facile synthesis of CoFe2O4@MIL-53(Al) nanocomposite for fast dye removal: Adsorption models, optimization and recyclability

The global occurrence of textile dyes pollution has recently emerged, posing a serious threat to ecological systems. To abate dye contamination, we here developed a novel magnetic porous CoFe₂O₄@MIL-53(Al) nanocomposite by incorporating magnetic CoFe₂O₄ nanoparticles with MIL-53(Al) metal-organic framework. This nanocomposite possessed a surface area of 197.144 m² g^-1 and a pore volume of 0.413 cm³ g^-1. The effect of contact time (5-120 min), concentration (5-50 mg L^-1), dosage (0.1-1.0 g L^-1), and pH (2-10) on Congo red adsorption was clarified. CoFe₂O₄@MIL-53(Al) could remove 95.85% of Cong red dye from water with an accelerated kinetic rate of 0.6544 min^-1 within 10 min. The kinetic and isotherm models showed the predominance of Bangham and Temkin. According to Langmuir, the maximum uptake capacities of CoFe₂O₄@MIL-53(Al), CoFe₂O₄, and MIL-53(Al) adsorbents were 43.768, 17.982, and 15.295 mg g^-1, respectively. CoFe₂O₄@MIL-53(Al) was selected to optimize Cong red treatment using Box-Behnken experimental design. The outcomes showed that CoFe₂O₄@MIL-53(Al) achieved the highest experimental uptake capacity of 35.919 mg g^-1 at concentration (29.966 mg L^-1), time (14.926 min), and dosage (0.486 g L^-1). CoFe₂O₄@MIL-53(Al) could treat dye mixture (methylene blue, methyl orange, Congo red, malachite green, and crystal violet) with an outstanding removal efficiency of 81.24% for 30 min, and could be reused up to five cycles. Therefore, novel recyclable and stable CoFe₂O₄@MIL-53(Al) is recommended to integrate well with real dye treatments systems.

Intelligent modelling for the elimination of lanthanides (La3+, Ce3+, Nd3+ and Eu3+) from aqueous solution by magnetic CoFe2O4 and CoFe2O4-GO spinel ferrite nanocomposites

In this research, a novel CoFe₂O₄-GO (Graphen Oxide) resulting from the combination of high applicable magnetic and organic base materials and synthesized with a simple and fast co-precipitation route was synthesized for the REEs (Rare Earth Elements) extraction. This adsorbent could remove the La³⁺, Ce³⁺, Nd³⁺ and Eu³⁺ by maximum adsorption capacity of 625, 626, 714.2, 1111.2 mg/g at optimized pH = 6, respectively. A data-driven model was obtained using Group Method of Data Handling (GMDH)-based Neural Network to estimate the adsorption capacity of these LREEs as a function of time, pH, temperature, adsorbent ζ (zeta)- potential, initial concentration of lanthanides ions, and ε which is defined by the physico-chemical properties of lanthanides. The results clearly indicated that the model estimate the experimental values with good deviation (mostly less than 10%) and it can be used for the prediction of the results from other similar researches with less than 25% deviation. The results of sensitivity analysis indicated that the adsorption capacity is more sensitive to pH of the solution, temperature, and ε. Finally, the desorption studies showed an excellent removal efficiency (97%) at least for three adsorption-desorption cycles. These results claimed that the CoFe₂O₄-GO is a highly efficient adsorbent for the REEs extraction.

Removal of organic micropollutans by adsorptive membrane

Various emerging organic micropollutants, such as pharmaceuticals, have attracted the interest of the water industry during the last two decades due to their insufficient removal during conventional water and wastewater treatment methods and increasing demand for pharmaceuticals projected to climate change-related impacts and COVID-19, nanosorbents such as carbon nanotubes (CNTs), graphene oxides (GOs), and metallic organic frameworks (MOFs) have recently been extensively explored regarding their potential environmental applications. Due to their unique physicochemical features, the use of these nanoadsorbents for organic micropollutans in water and wastewater treatment processes has been a rapidly growing topic of research in recent literature. Adsorptive membranes, which include these nanosorbents, combine the benefits of adsorption with membrane separation, allowing for high flow rates and faster adsorption/desorption rates, and have received a lot of publicity in recent years. The most recent advances in the fabrication of adsorptive membranes (including homogeneous membranes, mixed matrix membranes, and composite membranes), as well as their basic principles and applications in water and wastewater treatment, are discussed in this review. This paper covers ten years, from 2011 to 2021, and examines over 100 published studies, highlighting that micropollutans can pose a serious threat to surface water environments and that adsorptive membranes are promising, particularly in the adsorption of trace substances with fast kinetics. Membrane fouling, on the other hand, should be given more attention in future studies due to the high costs and restricted reusability.

Covalent and Non-covalent Functionalized Nanomaterials for Environmental Restoration

Nanotechnology has emerged as an extraordinary and rapidly developing discipline of science. It has remolded the fate of the whole world by providing diverse horizons in different fields. Nanomaterials are appealing because of their incredibly small size and large surface area. Apart from the naturally occurring nanomaterials, synthetic nanomaterials are being prepared on large scales with different sizes and properties. Such nanomaterials are being utilized as an innovative and green approach in multiple fields. To expand the applications and enhance the properties of the nanomaterials, their functionalization and engineering are being performed on a massive scale. The functionalization helps to add to the existing useful properties of the nanomaterials, hence broadening the scope of their utilization. A large class of covalent and non-covalent functionalized nanomaterials (FNMs) including carbons, metal oxides, quantum dots, and composites of these materials with other organic or inorganic materials are being synthesized and used for environmental remediation applications including wastewater treatment. This review summarizes recent advances in the synthesis, reporting techniques, and applications of FNMs in adsorptive and photocatalytic removal of pollutants from wastewater. Future prospects are also examined, along with suggestions for attaining massive benefits in the areas of FNMs.

Adsorption Behaviors of Cationic Methylene Blue and Anionic Reactive Blue 19 Dyes onto Nano-Carbon Adsorbent Carbonized from Small Precursors

In this work, an innovative nano-carbon material (N-CM) adsorbent was reported for exploring its adsorption behaviors toward cationic methylene blue (MB) and anionic reactive blue 19 (RB19) pollutants. The proposed N-CM was synthesized by a one-step solvothermal treatment of citric acid and zinc gluconate small precursors. N-CM consists of nanosheets that have an advantageous specific surface area, large sp2/sp3 hybridized domains, and abundant nitrogen/oxygen-containing surface functional groups. The synergistic effects of these features are conducive to the MB and RB19 adsorption. Different from anionic RB19 adsorption (79.54 mg/g) by the cooperative π-π stacking and hydrogen bonding, cationic MB adsorbed onto N-CM mainly by the electrostatic attraction at the natural pH solution (> pHpzc), with an adsorption capacity up to 118.98 mg/g. Interestingly, both MB and RB19 adsorption conformed to the pseudo-second order kinetic (R2 ≥ 0.995) and Langmuir isothermal (R2 ≥ 0.990) models, accompanied by similar maximum monolayer adsorption capacities of 120.77 and 116.01 mg/g, respectively. Their adsorption processes exhibited spontaneously endothermic characteristics. Moreover, N-CM showed superior selective capability toward MB in different mixed dye systems, with high removal efficiencies of 73−89%. These results demonstrate that the high-performance carbon adsorbent prepared from small precursors via low-temperature carbonization shows great potentials in wastewater treatment.

Facile access to high-efficiency degradation of tetracycline hydrochloride with structural optimization of TiN

As a broad-spectrum antibiotic, tetracycline has become a potential ecological hazard. Herein, titanium nitride (TiN), with an advantageous structure, was synthesized by simple heating rate regulation and constructed for tetracycline hydrochloride (TC-HCl) degradation under light irradiation. All the samples were characterized by X-ray diffraction (XRD), N2-adsorption/desorption isotherm, ultraviolet-visible diffuse reflectometry (DRS), scanning electron microscopy (SEM), and electrochemical impedance spectroscopy (EIS). The results showed that the as-prepared TiN-x catalysts exhibited obviously enhanced photocatalytic property toward TC-HCl degradation compared with the commercial pure phase TiN (p-TiN). According to the results of photocatalytic degradation, TiN synthesized at 6 °C/min heating rate had the best removal rate of TC-HCl (90%) after dark reaction for 10 min and photo-degradation for 90 min. In addition, the trapping experiments have demonstrated that the photogenerated holes (h+) and superoxide radical ([Formula: see text]) are the main oxidation products of the present system. Strikingly, the reuse experiments showed high stability of TiN.

Effective mitigation of single-component and mixed textile dyes from aqueous media using recyclable graphene-based nanocomposite

The present study reported the synthesis and utilization of a graphene-based hybrid nanocomposite (MnFe₂O₄/G) to mitigate several synthetic dyes, including methylene blue, malachite green, crystal violet, and Rhodamine B. This adsorbent was structurally analyzed by several physicochemical techniques such as X-ray diffraction, Fourier-transform infrared spectroscopy, scanning electron microscopy, Raman spectroscopy, N₂ adsorption-desorption isotherm measurement, point of zero charge, and Boehm titrations. BET surface area of MnFe₂O₄/G was measured at 382.98 m²/g, which was substantially higher than that of MnFe₂O₄. MnFe₂O₄/G possessed diverse surface chemistry properties with the presence of many functional groups such as carboxylic acid, phenolic, lactone, and basic groups. MnFe₂O₄/G was used to remove synthetic dyes in the aqueous media. The effect of many factors, e.g., concentration (5-50 mg/L), pH (4-10), dose (5-20 mg), and temperature (25-45 °C) on adsorption performance of MnFe₂O₄/G was conducted. Kinetic, isotherm, intraparticle, and thermodynamic models were adopted for investigating adsorption phenomenon of dyes on MnFe₂O₄/G. The maximum adsorption capacity of dyes over MnFe₂O₄/G was found as Rhodamine B (67.8 mg/g) < crystal violet (81.3 mg/g) < methylene blue (137.7 mg/g) < malachite green (394.5 mg/g). Some tests were performed to remove mixed dyes, and mixed dyes in the presence of antibiotics with total efficiencies of 65.8-87.9% after 120 min. Moreover, the major role of π-π stacking interaction was clarified to gain insight into the adsorption mechanism. MnFe₂O₄/G could recycle up to 4 cycles, which may be beneficial for further practical water treatment.

Rapid and Efficient Removal of Anionic Dye in Water Using a Chitosan-Coated Iron Oxide-Immobilized Polyvinylidene Fluoride Membrane

Anionic dyes are one of the most serious contaminants in water as these molecules are known to be toxic to many living organisms. Herein, we report the development of functionalized polyvinylidene fluoride membranes modified with chitosan-coated iron oxide nanomaterials (Fe-PVDF) for the efficient treatment of anionic dye-contaminated water. Aqueous solutions of anionic dyes could be captured rapidly by passing through the functionalized membrane under reduced pressure. Under neutral conditions, Fe-PVDF showed a maximum removal capacity of 74.6 mg/g for Evans blue (EB) through the adsorption process. In addition, the adsorption capacity was significantly enhanced up to 434.78 mg/g under acidic conditions. The adsorption process for EB matched well with the Langmuir model, indicating monolayer adsorption of the dye to the membrane surface. Moreover, Fe-PVDF can be reusable by a simple washing step in an alkaline solution, and thus, the composite membrane was applied several times without a significant decrease in its adsorption performance. The same composite membrane was further applied to the removal of five other different anionic dyes with high efficiencies. The adsorption mechanism can be explained by the electrostatic interaction between the positively charged chitosan and the negatively charged dye as well as the affinity of the sulfate groups in dye molecules for the surface of the iron oxide nanoparticles. The easy preparation and rapid decolorization procedures make this composite membrane suitable for efficient water treatment.

Graphene-based materials for metronidazole degradation: A comprehensive review

Due to its cytotoxic effect, metronidazole (MNZ) is a drug commonly used to treat bacterial, protozoal, and microaerophilic bacterial infections. After consumption, it undergoes a series of metamorphic reactions that lead to the degradation of oxidized, acetylated, and hydrolyzed metabolites in the environment. To eliminate such pollutants, due to their high potential, adsorption and photocatalysis extensive processes are used in which graphene can be used to improve efficiency. This review analyses the use of graphene as an absorbent and catalyst with a focus on absorption and photocatalytic degradation of MNZ by graphene-based materials (GBMs). The parameters affecting the adsorption, and photocatalytic degradation of MNZ are investigated and discussed. Besides, the basic mechanisms occurring in these processes are summarized and analyzed. This work provides a theoretical framework that can direct future research in the field of MNZ removal from aqueous solutions.

Comparative study on the removal of organic pollutants by magnetic composite and pre-magnetized zero-valent iron activated persulfate

The rapid development of global logistics has led to the overuse of packaging cartons, causing problems for municipal solid waste disposal. Diverse methods of exploiting the potential value of waste cartons are needed. Herein, we fabricated a magnetic composite (MC) from waste cartons via a one-step hydrothermal treatment and characterized. Using methylene blue (MB) as a model organic pollutant, tests of the activation of persulfate (PS) via the MC for the removal of MB were performed. Meanwhile, a comparison with activation with pre-magnetized zero-valent iron (Pre-ZVI/PS) was made. The comparative results show that the removal of MB was successfully accomplished with both Pre-ZVI/PS and MC/PS. Specifically, MC/PS could remove almost 100 % of MB, with the COD removal efficiency reaching over 70 % when the MB concentration was 50 mg/L at 80 min under different pH conditions. Even when reused twice, the MC still displayed robust activation performance. Additionally, we evaluated the lifetime of magnetic memory for Pre-ZVI, and first found its consecutive loss of pre-magnetization over 30 days, corresponding to the incremental attenuation of reaction rate constants in the Pre-ZVI-activated PS process. Overall, activating PS using the MC is a promising advanced oxidation technology and also provides a valuable reference on the valorization of lignocellulosic biomass.

Recent Progress on Nanomaterial-Based Membranes for Water Treatment

Nanomaterials have emerged as the new future generation materials for high-performance water treatment membranes with potential for solving the worldwide water pollution issue. The incorporation of nanomaterials in membranes increases water permeability, mechanical strength, separation efficiency, and reduces fouling of the membrane. Thus, the nanomaterials pave a new pathway for ultra-fast and extremely selective water purification membranes. Membrane enhancements after the inclusion of many nanomaterials, including nanoparticles (NPs), two-dimensional (2-D) layer materials, nanofibers, nanosheets, and other nanocomposite structural materials, are discussed in this review. Furthermore, the applications of these membranes with nanomaterials in water treatment applications, that are vast in number, are highlighted. The goal is to demonstrate the significance of nanomaterials in the membrane industry for water treatment applications. It was found that nanomaterials and nanotechnology offer great potential for the advancement of sustainable water and wastewater treatment.

Effect of the modification of magnetic graphene oxide with ionic liquid on the adsorption of nonionic surfactant NP10EO

The large-scale application of ionic surfactants in industrial and agricultural production has caused great harm to the environment due to by-products. In order to remove this pollutant from the environment, graphene oxide as an adsorption material has received extensive attention. However, practically, it is difficult to separate the GO from aqueous solutions, making water treatment on a large scale challenging. To allow the recycling of GO, as well as enhance its adsorption ability to remove surfactants from water, a composite of magnetic graphene oxide (MGO) and 1-dodecyl-3-methylimidazolium chloride ionic liquid (IL) was synthesized. The MGO was prepared by coprecipitation, and IL-MGO was prepared by ultrasonic impregnation. Nitrogen adsorption-desorption curves show that the specific surface area of the composite was increased by the addition of the IL, from 103.28 to 163.35 m²/g. Finally, the adsorption ability of MGO and IL-MGO for the nonionic surfactant NP10EO was investigated. The results showed that the adsorption of MGO on NP10EO fits the Langmuir isothermal model and the quasi-second-order kinetic model. In addition, the equilibrium adsorption capacity of NP10EO by MGO at 298K, 308K, and 318K can reach 87.03 mg/g, 156.25 mg/g, and 214.13 mg/g. The adsorption is an endothermic reaction that occurs spontaneously and is governed by physical adsorption. The adsorption of IL-MGO on NP10EO conforms to the Langmuir isotherm model and the quasi-second-order kinetic model. At 298K, 308K, and 318K, the equilibrium adsorption capacity of NP10EO by MGO reached 261.02 mg/g, 280.24 mg/g, and 295.03 mg/g, respectively. Compared with the two results, the incorporation of IL greatly improved the adsorption capacity of MGO to NP10EO.

Molecular dynamics simulations of hyperbranched poly(ethylene imine)-graphene oxide nanocomposites as dye adsorbents for water purification

Atomistically detailed molecular dynamics simulations were employed to study the adsorption capacity of graphene-oxide-based (GO) aqueous systems for the methylene blue (MB) dye in the presence of branched poly(ethylene imine) (BPEI) polymers. The polymeric component was either freely mixed or chemically attached to GO. The main focus was the elucidation of the effects originating from the presence of BPEI molecules in the association of MB with the formed GO complexes. The effect of temperature was also examined. It was found that the presence of the cationic BPEI molecules results in the formation of a distinct microenvironment characterized by a polymer-mediated interconnected morphology which promotes the development of larger-sized MB clusters. These clusters were found to form in the vicinity of the GO flakes, increasing thus the adsorption capacity of the dye molecules in the polymer-containing systems. Particularly in the system with the BPEI-functionalized GO flakes, a persistent percolated structure is formed, which results in a more restricted diffusion of the MB molecules, increasing thus significantly their residence time close to the GO surface. The clustering behavior of MB was found to be temperature-dependent in the BPEI-based models, providing useful information regarding the conditions for optimal adsorption performance of such membranes, in nanofiltration processes.

In-situ investigation of dye pollutant adsorption performance on graphitic carbon nitride surface: ATR spectroscopy experiment and MD simulation insight

The adsorption performances on graphitic carbon nitride (g-C₃N₄) surface were investigated for organic dye pollutants by both experimental and calculation methods. For experimental investigation, adsorption thermodynamics and kinetics results were in-situ obtained and evaluated. With [Formula: see text] by Langmuir modeling^, g-C₃N₄ showed superior adsorption spontaneity of MB⁺ >MO^-. With linear and exponential modeling, g^-C₃N₄ showed only adsorption process for MB⁺ but both diffusion and adsorption processes for MO^-. For simulation insight, all MB⁺ molecules but only parts of MO^- molecules were inclined to orient in parallel position at g-C₃N₄ surface after optimization during low concentration. And both MB⁺ and MO^- molecules were inclined to orient in perpendicular position at g-C₃N₄ surface after optimization during high concentration. Combined with experimental and calculation results, a molecular-orientation and force-dominance mechanism adsorption model are proposed to explain the surface interaction processes between dyes and g-C₃N₄. Electrostatic interaction and π-π stacking interaction were revealed to dominate for MB⁺ adsorption, and π-π stacking interaction and van der Waals force were revealed to dominate for MO^- adsorption. This work obtained 'localized' interfacial information and elucidated in-situ intermolecular interactions at g-C₃N₄ interface, which can provide fundamental basis for operation removal of organic dye pollutants by g-C₃N₄.

Magnetic nanoadsorbents for micropollutant removal in real water treatment: a review

Pure water will become a golden resource in the context of the rising pollution, climate change and the recycling economy, calling for advanced purification methods such as the use of nanostructured adsorbents. However, coming up with an ideal nanoadsorbent for micropollutant removal is a real challenge because nanoadsorbents, which demonstrate very good performances at laboratory scale, do not necessarily have suitable properties in in full-scale water purification and wastewater treatment systems. Here, magnetic nanoadsorbents appear promising because they can be easily separated from the slurry phase into a denser sludge phase by applying a magnetic field. Yet, there are only few examples of large-scale use of magnetic adsorbents for water purification and wastewater treatment. Here, we review magnetic nanoadsorbents for the removal of micropollutants, and we explain the integration of magnetic separation in the existing treatment plants. We found that the use of magnetic nanoadsorbents is an effective option in water treatment, but lacks maturity in full-scale water treatment facilities. The concentrations of magnetic nanoadsorbents in final effluents can be controlled by using magnetic separation, thus minimizing the ecotoxicicological impact. Academia and the water industry should better collaborate to integrate magnetic separation in full-scale water purification and wastewater treatment plants.

Adsorptive removal of dye in wastewater by metal ferrite-enabled graphene oxide nanocomposites

Dyes are hazardous compounds commonly found in industrial wastewaters. Efficient and inexpensive removal of dye molecules from the water matrix has been demonstrated by adsorption processes. Magnetic nano-adsorbents, such as metal ferrites, can be efficiently recovered from the reaction mixture after treating the pollutant. Herein, MFe₂O₄@GO (M = Cu, Co or Ni) was synthesized via solution combustion method for the removal of dye molecules from aqueous solutions. The characteristics of the MFe₂O₄@GO, including surface area and pore diameter, surface functional groups, and elemental composition, were examined. Methylene blue was used as representative dye pollutant. Batch adsorption results conformed to the Langmuir isotherm. Maximum adsorption capacities of the MFe₂O₄@GO (M = Cu, Co or Ni) were 25.81, 50.15 and 76.34 mg g^-1, respectively. Kinetics of methylene blue adsorption fitted the pseudo-second-order model. Overall, NiFe₂O₄@GO exhibited the highest adsorbent performance among the graphene-metal ferrites investigated, primarily because of its high specific surface area and presence of mesopores.

Insight into Organic Pollutant Adsorption Characteristics on a g-C3N4 Surface by Attenuated Total Reflection Spectroscopy and Molecular Dynamics Simulation

Herein the adsorption characteristics of zwitterionic dye pollutant Rhodamine B (Rh⁺B^-) on a g-C₃N₄ surface were investigated by both an attenuated total reflection spectroscopy (ATRS) experiment and a molecular dynamics simulation (MDS). For experimental investigation, g-C₃N₄ was coated on a silica optical fiber (SOF) surface to fabricate an adsorption film. According to the ATRS response, adsorption thermodynamics and thermodynamics results were in situ obtained and evaluated. The isothermal Langmuir model was used to calculate the adsorption equilibrium constants (K_ads) and adsorption energies (ΔG_ads) for Rh⁺B^- as 27.25 × 10⁴ M^-1 and -31.01 kJ mol^-1, respectively, which indicated the spontaneous adsorption behavior of Rh⁺B^- at the g-C₃N₄ surface. Using dynamic Elovich modeling, the rate constants of Rh⁺B^- were found to be k₁ = 0.0063 min^-1 and k₂ = 0.0004 min^-1, which indicated two-stage adsorption at the g-C₃N₄ surface. For theoretical simulation, adsorption configurations and adsorption energies were systematically calculated by a molecular dynamics simulation (MDS) . Rh⁺B^- molecules were inclined to orient in a parallel position at the g-C₃N₄ surface during low concentration but a perpendicular position at the g-C₃N₄ surface during high concentration. Combined with experimental and calculation results, this work revealed the microscopic adsorption performance and elucidated the intermolecular interaction between localized interfaces of g-C₃N₄ and hazardous dye pollutant. We propose an adsorption model to explain the process of surface interaction, which is based on molecular orientation and a force-driven mechanism. Electrostatic attraction and π-π interaction dominated the adsorption interaction with an adsorption energy of ΔG_low(ads) = -38.96 kJ mol^-1 for low Rh⁺B^- concentration, and electrostatic attraction dominated the adsorption interaction with an adsorption energy of ΔG_high(ads) = -25.76 kJ mol^-1 for high Rh⁺B^- concentration. This work can provide a fundamental basis for a dye-pollutants removal application by g-C₃N₄ in both adsorption and photocatalyzation.