Assessment of automated off-line solid-phase extraction LC-MS/MS to monitor EPA priority endocrine disruptors in tap water, surface water, and wastewater

Combined collection systems of sewage and rainfall runoff seriously affect the spatial distributions of natural estrogens and their conjugates in river water: Insights from the Pearl River of China

So far, little has been known about how the combined collection systems of sewage and rainfall runoff (CCSs) affect emerging contaminants in river water. To fill up the knowledge gap, this study was conducted to investigate the spatial distributions of three natural estrogens (NEs, i.e., estrone (E1), 17β-estradiol (E2) and estriol (E3)) and their conjugates (C-NEs) in the Pearl River in the wet and dry seasons. Results showed that the respective average concentrations of NEs and C-NEs at different locations alongside the Pearl River in the wet season were 7.3 and 1.8 times those in the dry season. Based on estrogen equivalence (EEQ), the average estimated EEQ level in the Pearl River waters in the wet season was nearly 10 times that in the dry season. These seemed to imply that the CCSs in the wet season not only cause untreated sewage into the receiving water body, but greatly decrease the removal efficiency of NEs and C-NEs in wastewater treatment plant. Furthermore, the estimated annual loads of E1, E2, and E3 to the Pearl River in the wet season accounted for about 88.6 %, 100 %, and 99.3 % of the total annual loads. Consequently, this work for the first time demonstrated that the CCSs in cities with high precipitation are unfavorable for controlling of emerging contaminants.

Global insight into the occurrence, treatment technologies and ecological risk of emerging contaminants in sanitary sewers: Effects of the SARS-CoV-2 coronavirus pandemic

The SARS-CoV-2 pandemic caused changes in the consumption of prescribed/non-prescribed drugs and the population's habits, influencing the detection and concentration of emerging contaminants (ECs) in sanitary sewage and harming environmental and health risks. Therefore, the present work sought to discuss current literature data on the effects of the "COVID-19 pandemic factor" on the quality of raw sewage produced over a five-year period (2018-2019: pre-pandemic; 2020-2022: during the pandemic) and biological, physical, chemical and hybrid treatment technologies, influencing factors in the removal of ECs and potential ecological risks (RQs). Seven hundred thirty-one publications correlating sewage and COVID-19 were identified: 184 pre-pandemic and 547 during the pandemic. Eight classes and 37 ECs were detected in sewage between 2018 and 2022, with the "COVID-19 pandemic factor" promoting an increase in estrogens (+31,775 %), antibiotics (+19,544 %), antiepileptics and antipsychotics (+722 %), pesticides (+200 %), analgesics, anti-inflammatories and anticoagulants (+173 %), and stimulant medications (+157 %) in sanitary sewage. Among the treatment systems, aerated reactors integrated into biomembranes removed >90 % of cephalexin, clarithromycin, ibuprofen, estrone, and 17β-estradiol. The absorption, adsorption, and biodegradation mechanisms of planted wetland systems contributed to better cost-benefit in reducing the polluting load of sewage ECs in the COVID-19 pandemic, individually or integrated into the WWTP. The COVID-19 pandemic factor increased the potential ecological risks (RQs) for aquatic organisms by 40 %, with emphasis on clarithromycin and sulfamethoxazole, which changed from negligible risk and low risk to (very) high risk and caffeine with RQ > 2500. Therefore, it is possible to suggest that the COVID-19 pandemic intensified physiological, metabolic, and physical changes to different organisms in aquatic biota by ECs during 2020 and 2022.

A functionalized glass fiber as the adsorbent for efficient analysis of endocrine disruptors in aqueous environments

Estrogens and bisphenols are typical endocrine disruptors (EDs) that pose a potential hazard to the human body due to their widespread presence in aqueous environments. In this study, a β-cyclodextrin porous crosslinked polymer (β-CD-PCP) was prepared in-situ on a glass fiber surface by a nucleophilic substitution reaction. An effective and sensitive solid phase microextraction method using functionalized glass fiber with β-CD-PCP coating as the adsorbent was established for the detection of 11 EDs in a water environment. The β-CD-PCP was in-situ prepared on a glass fiber surface by a nucleophilic substitution reaction. The β-CD-PCP successfully separated five estrogens (ESTs) and six bisphenols (BPs) through hydrophobic and π-π interactions. The conditions affecting extraction were optimized. Under the optimized conditions, the ESTs obtained a high enrichment effect (1795-2328), low limits of detection (0.047 µg L-1) and a good linearity range (0.2-15.0 µg L-1). Furthermore, the spiked recoveries of analyte ESTs in aqueous environments were between 82.9-115.7 %. The results indicated that the prepared functionalized glass fibers exhibited good adsorption properties, and the established analytical method was reliable for monitoring trace ESTs and BPs in aqueous environments.

Summary recommendations on "Analytical methods for substances in the Watch List under the Water Framework Directive"

The Watch List (WL) is a monitoring program under the European Water Framework Directive (WFD) to obtain high-quality Union-wide monitoring data on potential water pollutants for which scarce monitoring data or data of insufficient quality are available. The main purpose of the WL data collection is to determine if the substances pose a risk to the aquatic environment at EU level and subsequently to decide whether a threshold, the Environmental Quality Standards (EQS) should be set for them and, potentially to be listed as priority substance in the WFD. The first WL was established in 2015 and contained 10 individual or groups of substances while the 4th WL was launched in 2022. The results of monitoring the substances of the first WL showed that some countries had difficulties to reach an analytical Limit of Quantification (LOQ) below or equal to the Predicted No-Effect Concentrations (PNEC) or EQS. The Joint Research Centre (JRC) of the European Commission (EC) organised a series of workshops to support the EU Member States (MS) and their activities under the WFD. Sharing the knowledge among the Member States on the analytical methods is important to deliver good data quality. The outcome and the discussion engaged with the experts are described in this paper, and in addition a literature review of the most important publications on the analysis of 17-alpha-ethinylestradiol (EE2), amoxicillin, ciprofloxacin, metaflumizone, fipronil, metformin, and guanylurea from the last years is presented.

Determination of polyfluoroalkyl substances in cosmetic products using dispersed liquid-liquid extraction coupled with UHPLC-MS/MS

Human exposure to polyfluoroalkyl substances (PFASs) via cosmetics has been of increasing concern due to the tremendous detrimental health impacts of PFASs. Developing an effective method for extracting and determining PFASs in cosmetics is crucial in accurately assessing their corresponding human exposure risk. Herein, this study developed a new sample pre-treatment method to address the challenges posed by the variety and complexity of cosmetic matrices. Seventeen PFASs in cosmetic products, including 9 perfluoro carboxylic acids and 8 perfluorosulfonic acids, were simultaneously determined using ultra-high-performance liquid chromatography-tandem mass spectrometry (UHPLC-MS/MS). The whole pre-treatment process can be divided into three steps. In step 1, cosmetics with diverse matrix types can be effectively dispersed during extraction by using saturated sodium chloride-acetonitrile and saturated sodium chloride-tetrahydrofuran as extraction solvents. In step 2, the pre-purification step employs a potassium ferrocyanide-zinc acetate co-precipitant to remove high molecular weight interferents from the extraction solution, thereby enhancing the efficiency of solid-phase extraction (SPE). In step 3, WAX-SPE is utilized to further eliminate interferents from the extraction solution while concentrating the analytes, meeting the trace analysis requirements for PFASs in cosmetics. The method detection limits were 0.09-0.26 ng g-1. The recoveries ranged from 70.1% to 114.7%, with relative standard deviations in the range of 2.0-19.1%. The method was applied to cosmetic samples in the Guangzhou market, and the total concentration of PFASs ranged from 0 to 10.8 ng g-1. This method has strong anti-interference ability, good applicability, high sensitivity, and good reproducibility, making it suitable for the analysis and detection of perfluorinated acids in cosmetic samples. It provides technical support for cosmetics safety regulation.

Enhanced thyroxine removal from micro-polluted drinking water resources in a bio-electrochemical reactor amended with TiO2@GAC particles: Efficiency, mechanism and energy consumption

A three-dimensional bioelectrochemical system (3D-BES) with both electrocatalytic and biodegradation functions was designed and developed to enhance iodine-containing hormone removal from micro-polluted oligotrophic drinking water sources and to reduce energy consumption. Thyroxine (T4) removal efficiency was 99.0% in the 3D-BES amendment with TiO2@GAC as the particle electrodes, which was 20.5% higher than the total efficiency of single biodegradation (28.7%) plus electrochemical decomposition (49.8%). The high T4 removal efficiency was a result of biochemical synergistic degradation, enhancement of electron transfer and utilization, enrichment of functional microorganisms, and the expression of dehalogenation functional genes. The electron transfer was increased by 1.63 times in 3D-BES compared to the 2D-BES, which contributed to: (i) ∼17.8% enhancement of dehalogenation, (ii) 2.35 times enhancement of the attenuation rate, and (iii) 60% reduction in energy consumption. Moreover, the aggregation of microorganisms and the hydrophobic T4 onto TiO2@GAC shortened the transfer distance of matter and energy, which induced the degradation steps to be shortened and the toxic decay to be accelerated from T4 and its metabolites. These comprehensive functions also enhanced the 31.8% ATPase activity, 7.3% abundance of the functional reductive dehalogenation genera, and 52.3% dehalogenation genes expression for Pseudomonas, Ancylobacter, and Dehalogenimonas, which contributed to an increase in T4 removal. This work provides an environmental-friendly biochemical synergistic method for the detoxification of T4 polluted water.

Insights in Pharmaceutical Pollution: The Prospective Role of eDNA Metabarcoding

Environmental pollution is a growing threat to natural ecosystems and one of the world's most pressing concerns. The increasing worldwide use of pharmaceuticals has elevated their status as significant emerging contaminants. Pharmaceuticals enter aquatic environments through multiple pathways related to anthropogenic activity. Their high consumption, insufficient waste treatment, and the incapacity of organisms to completely metabolize them contribute to their accumulation in aquatic environments, posing a threat to all life forms. Various analytical methods have been used to quantify pharmaceuticals. Biotechnology advancements based on next-generation sequencing (NGS) techniques, like eDNA metabarcoding, have enabled the development of new methods for assessing and monitoring the ecotoxicological effects of pharmaceuticals. eDNA metabarcoding is a valuable biomonitoring tool for pharmaceutical pollution because it (a) provides an efficient method to assess and predict pollution status, (b) identifies pollution sources, (c) tracks changes in pharmaceutical pollution levels over time, (d) assesses the ecological impact of pharmaceutical pollution, (e) helps prioritize cleanup and mitigation efforts, and (f) offers insights into the diversity and composition of microbial and other bioindicator communities. This review highlights the issue of aquatic pharmaceutical pollution while emphasizing the importance of using modern NGS-based biomonitoring actions to assess its environmental effects more consistently and effectively.

Automated microextraction by packed sorbent of endocrine disruptors in wastewater using a high-throughput robotic platform followed by liquid chromatography-tandem mass spectrometry

An automated microextraction by packed sorbent followed by liquid chromatography-tandem mass spectrometry (MEPS-LC-MS/MS) method was developed for the determination of four endocrine disruptors-parabens, benzophenones, and synthetic phenolic antioxidants-in wastewater samples. The method utilizes a lab-made repackable MEPS device and a multi-syringe robotic platform that provides flexibility to test small quantities (2 mg) of multiple extraction phases and enables high-throughput capabilities for efficient method development. The overall performance of the MEPS procedure, including the investigation of influencing variables and the optimization of operational parameters for the robotic platform, was comprehensively studied through univariate and multivariate experiments. Under optimized conditions, the target analytes were effectively extracted from a small sample volume of 1.5 mL, with competitive detectability and analytical confidence. The limits of detection ranged from 0.15 to 0.30 ng L-1, and the intra-day and inter-day relative standard deviations were between 3 and 21%. The method's applicability was successfully demonstrated by determining methylparaben, propylparaben, butylated hydroxyanisole, and oxybenzone in wastewater samples collected from the São Carlos (SP, Brazil) river. Overall, the developed method proved to be a fast, sensitive, reliable, and environmentally friendly analytical tool for water quality monitoring.

Hierarchical porous zeolitic imidazolate framework‑8 supported hollow-fiber liquid-phase microextraction of nine typical phenolic pollutants in water samples followed by electrophoretic analysis

Hierarchical porous zeolitic imidazolate framework‑8 (HpZIF-8) have not only good chemical and thermal stability, but also pore structures of different sizes. In this work, HpZIF-8 supported hollow-fiber liquid-phase microextraction (HpZIF-8@HF-LPME) co-modified with tributyl phosphate and 2-nitroethyl benzene was firstly developed for purification and enrichment of nine typical phenolic pollutants followed by electrophoretic separation and amperometric detection (CE-AD). The key enrichment parameters were optimized by full factorial experimental and central composite designs. Under the optimum conditions, the maximum enrichment factors for the nine analytes were 479 (phenol), 249 (2-chlorophenol), 821 (4-chlorophenol), 1253 (3-methylphenol), 1376 (2,4-dichlorophenol), 1078 (2,4,6-trichlorophenol), 200 (pentachlorophenol), 614 (4-nitrophenol) and1827 times (bisphenol A), respectively. The limits of detection were 0.060-1.5 µg L-1 (S/N = 3) in real sample matrixes. This proposed method has been successfully applied to water samples with high ionic strength, and the average recoveries were in the range of 80.2-118.0%. This developed method of HpZIF-8@HF-LPME/CE-AD needs no desorption and derivatization, providing an alternative for monitoring typical phenolic pollutants in water samples.

Magnetic Rubber@ magnesium aluminum layered double hydroxide as nanostructured sorbent; application in determination of estrogenic hormones and bisphenol A

A magnetic solid-phase extraction (MSPE) method was developed for the enrichment of trace amounts of estrone (E1), 17-β-estradiol (E2) and bisphenol A (BPA) from aqueous samples using the Rubber-Fe3O4@SiO2@Mg-Al Layered double hydroxide followed by determination by HPLC. The proposed sorbent was characterized by X-ray diffraction, Field emission scanning electron microscopy, Fourier transform infrared spectroscopy, Vibrating-sample magnetometer, Thermal gravimetric analysis, N2 adsorption/desorption Brunauer-Emmett-Teller surface analysis, Barrett-Joyner-Halenda pore size analysis and Energy dispersive X-ray spectroscopy. Factors affecting the extraction efficiency such as pH, ionic strength, extraction temperature and time, desorption solvent and time were optimized. The limit of detection and quantification were obtained as 0.33, 1 µg L-1 for the E1 and E2 and BPA, respectively. Also, linear range of the method were 1-150, 1-100 and 1-150 µg L-1for E1, E2, and BPA, respectively. Relative standard deviations (RSD%) for the repeatability of extraction on one sorbent were obtained as 2.98, 1.31 and 3.50%, also, sorbent to sorbent repeatability were investigated and RSD% values were obtained as 7.58, 8.35 and 8.12% for E1, E2 and BPA, respectively.

Bisphenol A detection based on nano gold-doped molecular imprinting electrochemical sensor with enhanced sensitivity

A facile electrochemical sensor based on nano gold-doped molecularly imprinted polymer (MIP) was proposed to realize the selective detection of bisphenol A (BPA) with enhanced sensitivity. Initially, gold-doped MIP (Au@MIP) film was constructed by electropolymerizing p-aminobenzoic acid (PABA) and BPA with in situ gold reduction to distribute gold nanoparticles nearby the imprinted cavities. Subsequently, the template molecules were further extracted from the polymer film, then the MIP could rebind with the template molecules to achieve specific detection of BPA. The nano gold-doped MIP increased the effective surface area and promoted conductivity when BPA was oxidized in the imprinted cavities, which improved the determination sensitivity. Under optimal conditions, the prepared sensor displayed a linear range from 0.5 to 100 μM for BPA detection with a detection limit of 52 nM. The designed sensor was further used to detect BPA in food samples, obtaining satisfactory recoveries from 96.7% to 107.6%.

A robust multi-residue method for the monitoring of 25 endocrine disruptors at ultra-trace levels in surface waters by SPE-LC-MS/MS

Estrogenic endocrine disruptors are one of the biggest ecotoxicological threats in water that pose a significant ecological burden and health-risk for humans due to their high biological activity and proven additive effects. Therefore, we have developed and validated the most comprehensive and ultra-sensitive analytical method published to date, for reliable quantification of 25 high-risk endocrine disruptors at their ecologically relevant concentrations: naturally excreted hormones (estradiol, estrone, estriol, testosterone, corticosterone, and progesterone), synthetic hormones used for contraception and menopausal symptoms (ethinylestradiol, drospirenone, chlormadinone acetate, norgestrel, gestodene, tibolone, norethindrone, dienogest, and cyproterone) and bisphenols (BPS, BPA, BPF, BPE, BPAF, BPB, BPC, and BPZ). It is based on a solid-phase extraction of water samples, followed by a robust dansyl chloride derivatization with detection by liquid chromatography-tandem mass spectrometry with a single sample preparation and two analytical methods using the same analytical column and mobile phases. The achieved limits of quantitation are in the sub-ng L^-1 range, and detection limits as low as 0.02 ng L^-1, meeting the newest proposal for environmental quality standards (EQS) by the EU water framework directive for estradiol and ethinylestradiol. The method was extensively validated and applied to seven representative Slovenian water samples, where we detected 21 out of 25 analytes; 13 were quantified in at least one sample. Estrone and progesterone were quantified in all samples, reaching levels up to 50 ng L^-1; ethinylestradiol was higher than the current EQS (0.035 ng L^-1) in three samples, and estradiol was above its EQS (0.4 ng L^-1) in one sample, proving the method's applicability and the necessity for monitoring these pollutants.

Validation of an isotope dilution mass spectrometry (IDMS) measurement procedure for the reliable quantification of steroid hormones in waters

Reliable data are compulsory to efficiently monitor pollutants in aquatic environments, particularly steroid hormones that can exert harmful effects at challenging analytical levels below the ng L^-1. An isotope dilution two-step solid-phase extraction followed by an ultra-performance liquid chromatography separation coupled to tandem mass spectrometry (UPLC-MS/MS) detection method was validated for the quantification of 21 steroid hormones (androgens, estrogens, glucocorticoids, and progestogens) in whole waters. To achieve a realistic and robust assessment of the performances of this method, the validation procedure was conducted using several water samples representative of its intended application. These samples were characterized in terms of concentration of ionic constituents, suspended particulate matter (SPM), and dissolved organic carbon contents (DOC). For estrogens that are part of the European Water Framework Directive Watchlist (17beta-estradiol and estrone), the performances met the European requirements (decision 2015/495/EU) in terms of limit of quantification (LQ) and measurement uncertainty. For 17alpha-ethinylestradiol, the challenging LQ of 0.035 ng L^-1 was reached. More generally, for 15 compounds out of 21, the accuracy, evaluated in intermediate precision conditions at concentrations ranging between 0.1 and 10 ng L^-1, was found to be within a 35% tolerance. The evaluation of the measurement uncertainty was realized following the Guide to the expression of Uncertainty in Measurement. Finally, a water monitoring survey demonstrated the suitability of the method and pointed out the contamination of Belgium rivers by five estrogens (17alpha-ethinylestradiol, estriol, 17alpha-estradiol, 17beta-estradiol, and estrone) and three glucocorticoids (betamethasone, cortisol, and cortisone) which have been up to now poorly documented in European rivers.

Simultaneous trace determination of three natural estrogens and their sulfate and glucuronide conjugates in municipal waste and river water samples with UPLC-MS/MS

Analytical method for three natural estrogens (NEs) and their sulfate and glucuronide conjugates in waste and river waters using solid-phase extraction (SPE) coupled with ultra-performance liquid chromatography tandem mass spectrometry (UPLC-MS/MS) has been available, but problems including poor recovery exist. In order to solve these, some optimizations have been performed in this work. For sample preparation, both rinse and elution solutions were optimized, in which 6 mL of MeOH/water (1:9, v/v), MeOH/Ace/water (10:2:88, v/v/v), and MeOH/NH₄OH/water (10:2:88, v/v/v) were determined as the rinse solution, while 6 mL of 2.0% NH₄OH/MeOH was determined as the elution solution for conjugated NEs (C-NEs). For mobile phase, addition of NH₄F could obviously enhance the signal response of the nine target compounds, and the optimized addition concentration was 0.5 mmol/L. The developed efficient method was validated and showed excellent linearity for each target compound (R² > 0.998), low limit of quantifications (LOQs, 0.07-1.29 ng/L) in four different water matrices, and excellent recovery efficiencies of 81.0-116.1% in influent, effluent, ultra-pure, and river water samples with low relative standard deviations (RSDs, 0.6-13.6%). The optimized method was successfully applied to influent, effluent, and Pearl River water, among which three NEs were all detected, while five C-NEs were found in the influent, three C-NEs were detected in the effluent, and two C-NEs were found in the Pearl River water, indicating the wide distribution of NEs and C-NEs in different water environments. This work provided a reliable and efficient analytical method for simultaneous trace determination of NEs and C-NEs, which had satisfactory absolute recoveries with low RSDs, low LOQs, and time-saving for both analysis and nitrogen drying.

Recent Trends in Multiclass Analysis of Emerging Endocrine Disrupting Contaminants (EDCs) in Drinking Water

Ingestion of water is a major route of human exposure to environmental contaminants. There have been numerous studies exploring the different compounds present in drinking water, with recent attention drawn to a new class of emerging contaminants: endocrine-disrupting compounds (EDCs). EDCs encompass a broad range of physio-chemically diverse compounds; from naturally occurring to manmade. Environmentally, EDCs are found as mixtures containing multiple classes at trace amounts. Human exposure to EDCs, even at low concentrations, is known to lead to adverse health effects. Therefore, the ability to evaluate EDC contamination with a high degree of sensitivity and accuracy is of the utmost importance. This review includes (i) discussion on the perceived and actual risks associated with EDC exposure (ii) regulatory actions that look to limit EDC contamination (iii) analytical methods, including sample preparation, instrumentation and bioassays that have been advanced and employed for multiclass EDC identification and quantitation.