Heterogeneous sono-Fenton-like process using martite nanocatalyst prepared by high energy planetary ball milling for treatment of a textile dye

Modified sono-Fenton process for oxidative degradation of chloramphenicol

Oxidative degradation of chloramphenicol (CAP) using a hybrid approach (US/HA+/n-Fe2O3/SPC) involving sodium percarbonate (SPC; "solid H2O2" carrier), Fe2O3 nanoparticles (n-Fe2O3; H2O2 decomposition catalyst), hydroxylamine in its protonated form (HA+; Fe (III) to Fe (II) reducer), and ultrasonic cavitation (to increase the generation of hydroxyl radicals) has been studied for the first time. The average size of n-Fe2O3 synthesized by the sonochemical method, as calculated according to the Debye-Scherrer equation, was ~ 18 nm. The maximum degradation degree of CAP (83.1%) and first-order oxidative degradation rate constant of CAP as 1.253 × 10-3 s-1 were achieved using the modified sono-Fenton process under the optimized conditions as the initial concentration of CAP - 50 mg/L, the molar ratio of CAP:HA+:n-Fe2O3:SPC of 1:100:100:100, pH as 3, the temperature as 318 K, the specific ultrasonic power as 53.3 W/L, and the treatment duration of 7200 s. In general, the efficiency and intensity of CAP degradation increased with a decrease in the pH value, an increase in the molar ratio of CAP:HA+:n-Fe2O3:SPC, a decrease in the initial concentration of CAP, an increase in temperature, and showed a minor change with the specific power of US. The synergistic coefficient for the combination of the US and the heterogeneous Fenton process was 17.9. The active participation of hydroxyl radicals in the oxidative degradation of CAP using the modified sono-Fenton process was confirmed by scavenging experiments performed using tert-butyl alcohol. The proposed process can be a promising direction in the remediation of pharmaceutical effluents with significant potential for commercial exploitation.

An optimized sono-heterogeneous Fenton degradation of olive-oil mill wastewater organic matter by new magnetic glutarlaldehyde-crosslinked developed cellulose

The present study highlights the olive mill wastewater (OMW) treatment characteristics through a sono-heterogeneous Fenton process using new designed [GTA-(PDA-g-DAC) @Fe₃O₄] and characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), thermogravimetric analysis (TGA), magnetic properties measurements, and point of zero charge (pH pzc) analysis. A preliminary removal study showed significant degradation efficiency (75%) occurred combining the magnetic synthesized catalyst [GTA-(PDA-g-DAC)@Fe3O4] ([catalyst] = 2 g/L) with US /H₂O₂ and maintaining 500WL^-1 ultrasonic power (US). The values obtained by US only were (13%), H₂O₂/US (18%), US/Fe₃O₄ (28%), and US /Fe₃O₄/H₂O₂(35%). The catalytic findings have shown that [GTA-(PDA-g-DAC)@Fe₃O₄] exhibited good properties for OMW compound's degradation. The sonocatalytic process coupling and extra oxidant addition resulted in the degradation substantial levels. For instance, the concomitant effect of degradation optimized parameters; H₂O₂ 10 mM, [GTA-(PDA-g-DAC) @Fe₃O₄] nanocomposites 2.5 g/L, at pH 3, and T 35 °C for 70 min resulted in an almost complete mineralization of aqueous OMW solution followed by a significant decolorization. Oxidation results exhibited efficient degradation rates in total phenolic compounds (TPC), total amino compounds (TAC), and chemical oxygen demand (COD) oxidation rate were 89.88, 92.75, and 95.66 respectively following the optimized sono-heterogeneous catalytic Fenton process. The prepared magnetic catalyst exhibited a good stability during repeated cycles. The gathered findings gave the evidence that sono-heterogeneous catalytic Fenton process is a promising treatment technology for OMW effluents.

Degradation of Diazo Congo Red Dye by Using Synthesized Poly-Ferric-Silicate-Sulphate through Co-Polymerization Process

The ability of poly-ferric-silicate-sulphate (PFSS) synthesized via a co-polymerization process has been applied for the removal of diazo Congo red dye. A novel degradation pathway of diazo Congo red dye by using PFSS is proposed based on LC-MS analysis. Diazo Congo red dye was successfully removed using synthesized PFSS at lower coagulant dosages and a wider pH range, i.e., 9 mg/L from pH 5 to 7, 11 mg/L at pH 9, and 50 mg/L at pH 11. The azo bond cleavage was verified by the UV-Vis spectra of diazo Congo red-loaded PFSS and FTIR spectra which showed disappearance of the peak at 1584 cm^-1 for -N=N- stretching vibrations. The synchronized results of UV-Vis spectra, FTIR, and the LC-MS analysis in this study confirmed the significance of the Si and Fe bond in PFSS towards the degradation of diazo Congo red dye. The successfully synthesized PFSS coagulant was characterized by FTIR, SEM, TEM, and HRTEM analysis. From this analysis, it was proven that PFSS is a polycrystalline material which is favorable for the coagulation-flocculation process. Based on all these findings, it was established that synthesized PFSS can be employed as a highly efficient polymeric coagulant for the removal of dye from wastewater.

Mechanochemical synthesis of catalysts and reagents for water decontamination: Recent advances and perspective

This paper aims to provide insights on mechanochemistry as a green and versatile tool to synthesize advanced materials for water remediation. In particular, mechanochemical methodologies for preparation of reagents and catalysts for the removal of organic pollutants are reviewed and discussed, focusing on those materials that, directly or indirectly, induce redox reactions in the contaminants (i.e., photo-, persulfate-, ozone-, and Fenton-catalysts, as well as redox reagents). Methods reported in the literature include surface reactivity enhancement for single-component materials, as well as multi-component material design to obtain synergistic effects in catalytic efficiency and/or reactivity. It was also amply demonstrated that mechanochemical surface activation or the incorporation of catalytic/reactive components boost the generation of reactive species in water by accelerating charge transfer, increasing superficial active sites, and developing pollutant absorption. Finally, indications for potential future developments in this field are debated.

Degradation of textile dyes from aqueous solution using tea-polyphenol/Fe loaded waste silk fabrics as Fenton-like catalysts

In this study, waste silk fabrics (SF) were modified with tea-polyphenols (TPs) and then iron (Fe²⁺). The modified silk fabrics (TP-SF/Fe) were characterized via Fourier-transform infrared (FTIR), energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) analysis. TP-SF/Fe was used in the Fenton-like removal of dyes (methylene blue, reactive orange GRN, and cationic violet X-5BLN) from aqueous solutions with catalyst-like activity. The effects of different catalyst samples, contact time, H₂O₂ concentration, initial dye concentration, and pH values on dye removal were investigated. The results showed that the dye removal percentages with the TP-SF/Fe-H₂O₂ sample reached 98%, 97%, and 95% in 5–40 min for methylene blue, reactive orange GRN, and cationic violet X-5BLN, respectively. Different thermodynamic and kinetic models were used to check the best fit of the adsorption data. The results indicated that the Freundlich isotherm and pseudo first-order kinetics models were the best fits. Moreover, it was also proved that TP-SF/Fe would be quite an effective and economical adsorbent for the treatment of textile dye wastewater. This work provides the basis for waste silk application in the removal of dyes from wastewater.

In this study, waste silk fabrics were modified with tea-polyphenols then loaded with Fe²⁺ for degradation of dyes.

Enhancement of photo-Fenton catalytic activity with the assistance of oxalic acid on the kaolin-FeOOH system for the degradation of organic dyes

The Fenton reaction, as an important member of the advanced oxidation processes (AOPs), has gained extensive attention in recent years. However, the practical applications of the traditional Fenton process have been restricted by the poor degradation efficiency and the rigid pH range. In this study, we report a new strategy regarding the photo-Fenton oxidation of Rhodamine B (RhB) by kaolin-FeOOH (K-Fe) catalysts with the assistance of oxalic acid. It was found that the iron-oxalate complex was formed as oxalic acid was introduced into the K-Fe catalyst system by the chelation ability of oxalate. Benefiting from the high photosensitivity of the iron-oxalate complexes, the K-Fe/oxalic acid/H2O2/visible light system exhibited excellent catalytic activity towards the degradation of RhB under the optimized reaction conditions [(K-Fe) dosage = 1.0 g L-1, initial pH = 7.2, (oxalic acid) = 1.0 mM, (H2O2) = 0.5 mM], and its reaction rate constant for the degradation of RhB was 27.7 times greater than that of the K-Fe/H2O2/visible light system. More importantly, the K-Fe/oxalic acid/H2O2/visible system showed remarkable degradation efficiency over a wide pH range (3.3-10.8), which was superior to that of the traditional Fenton system. In addition, the degradation efficiency of RhB was found to remain at 94.7% after five cycles. This work is expected to provide an important approach for the application of the Fenton system.

Advanced Oxidation Processes for the Removal of Antibiotics from Water. An Overview

In this work, the application of advanced oxidation processes (AOPs) for the removal of antibiotics from water has been reviewed. The present concern about water has been exposed, and the main problems derived from the presence of emerging pollutants have been analyzed. Photolysis processes, ozone-based AOPs including ozonation, O3/UV, O3/H2O2, and O3/H2O2/UV, hydrogen peroxide-based methods (i.e., H2O2/UV, Fenton, Fenton-like, hetero-Fenton, and photo-Fenton), heterogeneous photocatalysis (TiO2/UV and TiO2/H2O2/UV systems), and sonochemical and electrooxidative AOPs have been reviewed. The main challenges and prospects of AOPs, as well as some recommendations for the improvement of AOPs aimed at the removal of antibiotics from wastewaters, are pointed out.

Heterogeneous sonocatalytic degradation of an anionic dye in aqueous solution using a magnetic lanthanum dioxide carbonate-doped zinc ferrite-reduced graphene oxide nanostructure

We report herein the sonochemical synthesis of a lanthanum dioxide carbonate (La₂O₂CO₃) and zinc ferrite (ZnFe₂O₄)-loaded reduced graphene oxide (LZF-rGO) nanoheterostructure for ultrasound (US)-assisted degradation of methyl orange (MO) from water. The MO was chosen as a model organic dye due to its toxicological and biodegradable-resistant properties. The LZF-rGO catalyst was characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy, transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy. The results of characterizations confirmed successful synthesis of sonocatalyst. Among different removal systems, US/LZF-rGO displayed outstanding sonodegradation performance for degradation of MO. The maximum removal efficiency of 75.9% was achieved using 0.2 g/L sonocatalyst, 20 mg/L MO, and 0.71 W/cm² US power intensity for 65 min. MO can be partially adsorbed on LZF-rGO but mostly sonodegraded by reactive radical species. The reaction conditions were optimized by investigating the effect of key operating parameters, including the sonocatalyst dosage, initial MO concentration, US power intensity, presence of inorganic salts, and use of an enhancer, on the decolorization of MO. The degradation intermediates produced from MO during the sonocatalytic process were identified by UPLC^®/MS-MS, and possible mechanism and pathway for the degradation of MO in the US/LZF-rGO system were also proposed. Reusability experiments with this sonocatalyst revealed a less than 10% drop in the degradation efficiency after four adsorption-desorption cycles.

Modeling azo dye removal by sono-fenton processes using response surface methodology and artificial neural network approaches

Textile industry wastewaters, which cause serious problems in the environment and human health, include synthetic dyes, complex organic pollutants, surfactants, and other toxic chemicals and therefore must be removed by advanced treatment methods. Determination of appropriate treatment conditions for efficient use of advanced treatment methods is an important and necessary step. In the last thirty years, the Artificial Neural Network-Genetic Algorithm (ANN-GA) and Response Surface Methodology (RSM) have emerged as the most effective empirical modeling and optimization methods especially for nonlinear systems. Reactive Red 195 azo dyestuff was chosen as the target pollutant. The color removal efficiency was modeled and optimized as a function of Sono-Fenton conditions such as H₂O₂ dosage, Fe²⁺ dosage, initial pH value, ultrasound power, and ultrasound frequency, using ANN-GA and RSM. The generalization and predictive ability of these methods were compared using the results of the 46 experimental sets generated by the Box-Behnken design. The mean square errors for these models are 3.01612 and 0.00295, and the regression coefficients showing the superiority of ANN in determining nonlinear behavior are 0.9856 and 0.9164, respectively. In optimal conditions, the prediction errors with hybrid ANN-GA and RSM models are 0.002% and 3.225%, respectively.

Magnetic nanocomposites decorated on multiwalled carbon nanotube for removal of Maxilon Blue 5G using the sono-Fenton method

Herein, multiwalled carbon nanotube-based Fe3O4 nano-adsorbents (Fe3O4@MWCNT) were synthesized by ultrasonic reduction method. The synthesized nano-adsorbent (Fe3O4@MWCNT) exhibited efficient sonocatalytic activity to remove Maxilon Blue 5G, a textile dye, and present in a cationic form, in aqueous solution under ultrasonic irradiation. The magnetic nano-adsorbent particles were characterized by high-resolution transmission electron microscopy (HR-TEM), transmission electron microscopy (TEM), Raman spectroscopy and X-ray diffraction (XRD). Some important parameters such as nano-adsorbent dosage, solution pH, initial dye and H2O2 concentration, reaction time, ultrasonic power and temperature were tested to determine the optimum conditions for the elimination of Maxilon Blue 5G dye. The reusability results showed that Fe3O4@MWCNT nano-adsorbent has a decrease of about 32.15% in the removal efficiency of Maxilon Blue 5G under ultrasonic irradiation after six times reuse. Additionally, in order to reveal the sufficient kinetic explanation, various experiments were performed at different temperatures and testing three kinetic models like the pseudo-first-order, pseudo-second-order and intraparticle diffusion for removal adsorption process of Maxilon Blue 5G using Fe3O4@MWCNT nano-adsorbent. The experimental kinetic results revealed that the adsorption process of Maxilon Blue 5G in the aquatic mediums using sono-Fenton method was found to be compatible with the intraparticle diffusion. Using kinetic models and studies, some activation parameters like enthalpy, entropy and Gibbs free energy for the adsorption process were calculated. The activation parameters indicated that Fe3O4@MWCNT nano-adsorbent could be used as an effective adsorbent for the removal of Maxilon Blue 5G as a textile dye and the adsorption process of Maxilon Blue 5G with Fe3O4@MWCNT nano-adsorbent is spontaneous.

Implementation of martite nanoparticles prepared through planetary ball milling as a heterogeneous activator of oxone for degradation of tetracycline antibiotic: Ultrasound and peroxy-enhancement

The aim of the present study was to employ martite nanoparticles synthesized through planetary ball milling instead of conventional sources of iron for the activation of Oxone in order to decompose tetracycline (TC) antibiotic in the aquatic phase. Accordingly, martite nanoparticles-activated Oxone exhibited a remarkable improvement in degrading TC molecules up to 87%. The results indicated an increased decomposition rate of TC with increasing Oxone concentration, martite nanoparticles dosage, and initial pH. In the absence of ultrasound, the decomposition rate of TC was 0.0481 min^-1 within 30 min, while the implementation of ultrasound at 320 W and addition of hydrogen peroxide at 40 mM led to increase in the decomposition rate up to 0.0770 and 0.0907 min^-1, respectively. The presence of carbonate and even persulfate ions suppressed the decomposition rate. Inversely, the addition of chloride and carbon tetrachloride enhanced the reactor performance in terms of TC degradation. Within four consecutive experimental runs, only 10.8% was dropped in the decomposition rate, indicating the appropriate reusability potential of martite nanoparticles. The results confirmed the appropriate ability of the treatment process in degrading and mineralizing the target pollutant but a longer exposure time is required for an efficient mineralization.

Degradation of tetracycline in a schorl/H2O2 system: Proposed mechanism and intermediates

Schorl could perform as an extremely promising catalyst for decomposing tetracycline hydrochloride (TC) due to its high degradation efficiency, low cost, chemical stability, easy recovery and repeatable utilization. Comparisons of TC degradation indifferent systems showed that schorl/H₂O₂ system exhibited the optimum pollutant elimination and TOC removal efficiencies. Kinetics and possible mechanisms of TC degradation were clarified. The OH generated on the schorl surface and O₂^-/HO₂ were the main reactive species responsible for TC oxidation. Six possible intermediates were identified, and possible transform mechanisms and pathways were explored. Active radicals were inclined to attack the CC double bond, dimethylamino and phenolic moieties of TC molecular. The principal intermediate products were generated through N-demethylation, oxidation and rearrangement.

Preparation of magnetite nanoparticles by high-energy planetary ball mill and its application for ciprofloxacin degradation through heterogeneous Fenton process

In this study, the heterogeneous Fenton oxidation of ciprofloxacin (CIP) in an aqueous solution was examined over the nano-sized magnetite (Fe₃O₄) as a catalyst supplied through high-energy planetary ball milling process. To characterize the magnetite samples after and before ball milling operation, the X-ray diffraction (XRD), High-resolution scanning electron microscopy (HR-SEM), energy-dispersive X-ray spectroscopy (EDX), Brunauer-Emmett-Teller (BET) and Fourier transform infrared spectroscopy (FTIR) analysis were applied. The catalytic properties of the magnetite were considerably improved because of the enhancement in its physical properties, resulted from milling process. The findings also indicated that 6 h ball-milled magnetite demonstrated better properties for elimination of CIP of about 89% following 120 min reaction at optimal conditions of H₂O₂ 12 mM, Fe₃O₄ 1.75 g L^-1, CIP 10 mg L^-1 and pH 3.0. The effects of various operational parameters, including the initial pH of the solution, H₂O₂ initial concentration, catalyst dosage, milling time and CIP initial concentration was investigated. Application of organic and inorganic scavengers considerably decreased the CIP removal efficiency. Correspondingly, with respect to the leached iron values at pH 3, it was concluded that CIP elimination was mainly occurred through heterogeneous Fenton procedure. This process included the adsorption and oxidation phases in which the hydroxyl radicals (OH) played a significant role. GC-MS analysis was used for recording of the generated intermediates of the CIP removal in the course of heterogeneous Fenton process.

Enhanced removal of basic violet 10 by heterogeneous sono-Fenton process using magnetite nanoparticles

The removal of basic violet 10 (BV10), which is known as a cationic dye, from aqueous solution was studied by employing a heterogeneous sono-Fenton process over the nano-sized magnetite (Fe₃O₄) which had been prepared by the milling of magnetite mineral using a high-energy planetary ball milling process. The magnetite samples were characterized using the X-ray diffraction (XRD), high resolution scanning electron microscopy (HR-SEM), energy-dispersive X-ray spectroscopy (EDX), Brunauer-Emmett-Teller (BET), Fourier transform infrared spectroscopy (FTIR), and inductively couple plasma mass spectrometer (ICP-MS). It was found that the catalytic activity of the ball-milled magnetite sample was enhanced along with the improvement in its physicochemical properties; also, the ball-milled magnetite of 6 h displayed the highest catalytic activity in BV10 removal by the heterogeneous sono-Fenton process as compared with that for 4 h (66.12% after 120 min) and 2 h (48% after 120 min).The effect of operational parameters, namely, pH solution, catalyst dosage, the initial H₂O₂ concentration, ultrasonic power and the initial BV10 concentration, on the removal efficiency (RE%) of BV10 was investigated. The optimum conditions for the BV10 RE% were: the pH value of 3, the catalyst dosage of 1.5 g L^-1, the initial H₂O₂ concentration of 36 mM, the ultrasonic power of 450 W L^-1, and the initial BV10 concentration of 30 mg L^-1. The RE% of BV10 was 75.94% at these conditions after the reaction time of 120 min. The trapping experiments revealed that OH radicals were the dominant oxidative species, but O₂^-/HO₂ radicals also had a partial role in the removal of BV10.The reusability of the magnetite nanoparticles revealed about 28% decrease in the removal efficiency within five consecutive runs. The results obtained through GC-MS analysis also confirmed the efficient removal of BV10 molecules in the aqueous solution during the process.

Degradation reaction of Diazo reactive black 5 dye with copper (II) sulfate catalyst in thermolysis treatment

The theme of present research demonstrates performance of copper (II) sulfate (CuSO₄) as catalyst in thermolysis process to treat reactive black 5 (RB 5) dye. During thermolysis without presence of catalyst, heat was converted to thermal energy to break the enthalpy of chemical structure bonding and only 31.62% of color removal. With CuSO₄ support as auxiliary agent, the thermally cleaved molecular structure was further destabilized and reacted with CuSO₄. Copper ions functioned to delocalize the coordination of π of the lone paired electron in azo bond, C=C bond of the sp² carbon to form C-C of the sp³ amorphous carbon in benzene and naphthalene. Further, the radicals of unpaired electrons were stabilized and RB 5 was thermally decomposed to methyl group. Zeta potential measurement was carried out to analyze the mechanism of RB 5 degradation and measurement at 0 mV verified the critical chemical concentration (CCC) (0.7 g/L copper (II) sulfate), as the maximum 92.30% color removal. The presence of copper (II) sulfate catalyst has remarkably increase the RB 5 dye degradation as the degradation rate constant without catalyst, k₁ is 6.5224 whereas the degradation rate constant with catalyst, k₂ is 25.6810. This revealed the correlation of conversion of thermal energy from heat to break the chemical bond strength, subsequent fragmentation of RB 5 dye molecular mediated by copper (II) sulfate catalyst. The novel framework on thermolysis degradation of molecular structure of RB 5 with respect to the bond enthalpy and interfacial intermediates decomposition with catalyst reaction were determined.

Heterogeneous sono-Fenton-like process using magnetic cobalt ferrite-reduced graphene oxide (CoFe2O4-rGO) nanocomposite for the removal of organic dyes from aqueous solution

We report herein the synthesis of monodisperse cobalt ferrite (CoFe₂O₄) nanoparticles (NPs) via a surfactant-assisted high temperature thermal decomposition method and then their assembly on reduced graphene oxide (rGO) to yield CoFe₂O₄-rGO nanocomposites, which displayed outstanding sonocatalytic activity for the removal of organic dyes from aqueous solutions under ultrasonic irradiation. As-prepared CoFe₂O₄-rGO nanocomposites were characterized by using transmission electron microscopy (TEM), high-resolution scanning electron microscopy (HR-SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Micro-Raman spectroscopy, Vibrating sample magnetometer (VSM) and inductively couple plasma mass spectrometer (ICP-MS). To evaluate the sonocatalytic activity of the CoFe₂O₄-rGO nanocomposites, the sonocatalytic removal of several organic dyes (AO7, AR17, BR46 and BY28) was studied. The reaction conditions were optimized by studying the effects of various key operating parameters such as pH, catalyst dosage, H₂O₂ initial concentration, initial dye concentration, ultrasonic power and reaction time on the removal of AO7 dye. The maximum removal efficiency of 90.5% was achieved at pH 3 using 0.08gL^-1 catalyst, 3mM H₂O₂ and 10mgL^-1 AO7 dye under 350W ultrasonic power in 120min of reaction time span. Experimental results revealed that the kinetic of the removal process could be described using Langmuir-Hinshelwood (L-H) kinetic model. The trapping experiments showed that O₂^·- radicals constitute the major reactive oxygen species (ROS) in the AO7 dye removal process. The reusability of the nanocomposites revealed about 22% drop in the removal efficiency within five consecutive runs. A possible sonocatalytic mechanism for the removal of organic dyes was also proposed. The intermediate by-products of the dye formed in the removal process were characterized by using the GC-MS technique.

One-step preparation of nanostructured martite catalyst and graphite electrode by glow discharge plasma for heterogeneous electro-Fenton like process

Natural Martite ore particles and graphite were modified by alternating current (AC) glow discharge plasma to form nanostructured catalyst and cathode electrode for using in the heterogeneous-electro Fenton-like (Het-EF-like) process. The performance of the plasma-treated martite (PTM) and graphite electrode (PTGE) was studied for the treatment of paraquat herbicide in a batch system. 85.78% degradation efficiency for 20 mg L^-1 paraquat was achieved in the modified process under desired operational conditions (i.e. current intensity of 300 mA, catalyst amount of 1 g L^-1, pH = 6, and background electrolyte (Na₂SO₄) concentration of 0.05 mol L^-1) which was higher than the 41.03% for the unmodified one after 150 min of treatment. The ecofriendly modification of the martite particles and the graphite electrode, no chemical needed, low leached iron and milder operational pH were the main privileges of plasma utilization. Moreover, the degradation efficiency through the process was not declined after five repeated cycles at the optimized conditions, which proved the stability of the nanostructured PTM and PTGE in the long-term usage. The archived results exhibit this method is the first example of high efficient, cost-effective, and environment-friendly method for generation of nanostructured samples.

Contaminants of emerging concern: a review of new approach in AOP technologies

The presence of contaminants of emerging concern (CECs) such as pharmaceuticals and personal care products (PPCPs), endocrine-disrupting compounds (EDCs), flame retardants (FRs), pesticides, and artificial sweeteners (ASWs) in the aquatic environments remains a major challenge to the environment and human health. In this review, the classification and occurrence of emerging contaminants in aquatic environments were discussed in detail. It is well documented that CECs are susceptible to poor removal during the conventional wastewater treatment plants, which introduce them back to the environment ranging from nanogram per liter (e.g., carbamazepine) up to milligram per liter (e.g., acesulfame) concentration level. Meanwhile, a deep insight into the application of advanced oxidation processes (AOPs) on mitigation of the CECs from aquatic environment was presented. In this regard, the utilization of various treatment technologies based on AOPs including ozonation, Fenton processes, sonochemical, and TiO₂ heterogeneous photocatalysis was reviewed. Additionally, some innovations (e.g., visible light heterogeneous photocatalysis, electro-Fenton) concerning the AOPs and the combined utilization of AOPs (e.g., sono-Fenton) were documented.

MnTiO3-driven low-temperature oxidative coupling of methane over TiO2-doped Mn2O3-Na2WO4/SiO2 catalyst

Oxidative coupling of methane (OCM) is a promising method for the direct conversion of methane to ethene and ethane (C₂ products). Among the catalysts reported previously, Mn₂O₃-Na₂WO₄/SiO₂ showed the highest conversion and selectivity, but only at 800° to 900°C, which represents a substantial challenge for commercialization. We report a TiO₂-doped Mn₂O₃-Na₂WO₄/SiO₂ catalyst by using Ti-MWW zeolite as TiO₂ dopant as well as SiO₂ support, enabling OCM with 26% conversion and 76% C₂-C₃ selectivity at 720°C because of MnTiO₃ formation. MnTiO₃ triggers the low-temperature Mn²⁺↔Mn³⁺ cycle for O₂ activation while working synergistically with Na₂WO₄ to selectively convert methane to C₂-C₃. We also prepared a practical Mn₂O₃-TiO₂-Na₂WO₄/SiO₂ catalyst in a ball mill. This catalyst can be transformed in situ into MnTiO₃-Na₂WO₄/SiO₂, yielding 22% conversion and 62% selectivity at 650°C. Our results will stimulate attempts to understand more fully the chemistry of MnTiO₃-governed low-temperature activity, which might lead to commercial exploitation of a low-temperature OCM process.

Ultrasound-assisted Fenton process using siderite nanoparticles prepared via planetary ball milling for removal of reactive yellow 81 in aqueous phase

Nano-sized siderite was used as catalyst for the heterogeneous Fenton process combined with ultrasonic irradiation to degrade reactive yellow 81 (RY-81) in the aqueous phase. As the most efficient process, nano-sized siderite prepared via ball milling was chosen to carry out the experiments. 6h milled siderite at initial pH of 3.0 led to the highest removal efficiency of 92.09% within the reaction time of 30min. At a short reaction time of 20min, increasing siderite nanoparticles dosage from 0.3 to 0.75g/L resulted in increasing removal efficiency from 49.82 to 79.86%, respectively, while further increase in the dosage caused a substantial decrease in the efficiency. In the case of the effect of solute concentration, increasing the dye up to 400mg/L led to a significant decrease in the removal efficiency (65.77%). The presence of 0.01M Na₂CO₃ and C₂H₅OH significantly diminished the decolorization efficiency of RY-81 (<10%) with initial concentration of 100mg/L. The intermediates produced during the treatment process were also identified using GC-MS analysis. This research suggested that ball milled siderite is a potential catalyst for the efficient decolorization of textile effluents via ultrasound-assisted Fenton process.

Fungal biomass as biosorbent for the removal of Acid Blue 161 dye in aqueous solution

Physical and thermal treatment was used to inactivate Trametes sp. SC-10 fungus. The resulting biomass was named BTV, characterized by analytical techniques such as SEM, EDX, FTIR, BET, and Barrett-Joyner-Halenda (BJH) model. pH, kinetic, and equilibrium adsorption studies with the Acid Blue 161 (AB-161) dye were investigated at 303.15 K. The kinetics of the biosorption process were examined at 600.00 and 1300 mg L^-1, using pseudo-first-order, pseudo-second-order, and Avrami fractional-order models. The maximum biosorption capacity of BTV for AB-161 dye was 221.6 mg g^-1. Considering the biosorption data and the functional groups of BTV, it can be inferred that the sorption mechanism of AB-161 is regulated by electrostatic interactions between ionized dye molecules and negative charges on BTV in an aqueous solution. Finally, the BTV was tested with a simulated effluent with 89.47% efficiency, presenting the BTV as a biosorbent for real effluents polluted with dyes.