Concentration of precious metals during their recovery from electronic waste

Potential of metal recovery from printed circuit boards in Brazil

In this study, the generation of domestic waste electrical and electronic equipment (WEEE) and waste printed circuit board (WPCB) were estimated, from 2015 to 2030. Based on the number of EEE put on the Brazilian market, the possession rate in the Brazilian households and obsolescence amounts of five EEE types were estimated using time series. The results show that, between 2015 and 2030, the quantity of WEEE generated per year will increase from 131.87 kt to 195.22 kt. In this period, WPCB generation will stay around 10% of WEEE generation. Additionally, this study shows that the urban mining potential of the materials recoverable from WPCB can be an important revenue source, with environmental benefits deriving from energy savings and a reduction in CO2 emissions. The results of this study provide a quantitative basis that may help decision makers develop strategic policies for WEEE management, considering material circularity.

Engineering a Metal Reductase for the Bioremediation of Anthropogenic Electronic Wastes: From Hg(II) to Au(III) and Ag(I) Enzymatic Reduction

Recovering precious metals from electronic waste (e-waste) using microbes presents a sustainable methodology that can contribute toward the maintenance of planetary health. To better realize the potential of bioremediation using engineered microbes, enzymes that mediate the reduction of Au(III) to Au(0) have been the subject of intense research. In this study, we report the successful engineering of a metal reductase, MerA, whose cognate substrate is mercury(II), toward other precious metals such as Au(III) and Ag(I). The engineered variant, G415I, exhibited a 15-fold increase in catalytic efficiency (k cat/K M) in Au(III) reduction to Au(0) and a 200-fold increase in catalytic efficiency in Ag(I) reduction to Ag(0) with respect to the wild-type enzyme. The apparent shift in preference toward noncognate metal ions may be attributed to the energetics of valency preference. The improved Au(III) reductase has an apparent increased preference toward monovalent cations such as Au(I) and Ag(I), with respect to divalent cations such as Hg(II), the cognate substrate of the progenitor MerA (an increase in K M of 5.0-fold for Hg(II), compared to a decrease in K M of 5.8-fold for Au(III) and 1.8-fold for Ag(I), respectively). This study further extends the mechanistic understanding of Au(III) bioreduction that could proceed through the stabilization of Au(I) en route to Au(0) and suggests that the biosynthesis of Au nanoparticles with high efficiency can be realized through the engineering of promiscuous metal reductases for precious metal recovery from e-wastes.

Utilization of the copper recovered from waste printed circuit boards as a metal precursor for the synthesis of TiO2/magnetic-MOF(Cu) nanocomposite: Application in photocatalytic degradation of pesticides in aquatic solutions

In this study, a number of leaching solutions (H2SO4, CuSO4 and NaCl) and an electrochemical method were used together for the separation of Cu from waste printed circuit boards. Secondly, the magnetic-MOF(Cu) was synthesized using the Cu recovered from waste printed circuit boards. Thereafter, TiO2/mag-MOF(Cu) composite was prepared and its photocatalytic activity was assessed in the photo degradation of two prominent organophosphorus pesticides, namely malathion (MTN) and diazinon (DZN). The catalytic structure of the MOF-based composite was fully characterized by various analyses such as XRD, SEM, EDAX, FT-IR, VSM and UV-vis. The obtained analyses confirmed the successful synthesis of TiO2/mag-MOF(Cu) composite. The synthesized composite exhibited highly efficient in the degradation of both pollutants under the following conditions: pH 7, contaminant concentration 1 mg/L, the catalyst dosage of 0.4 g/L, visible light intensity 75 mW/cm2 and reaction time of 45 min. First order kinetic model was best suited with the experimental results (R2: 0.97-0.99 for different MTN and DZN concentrations). Trapping studies revealed that superoxide radicals (O2•-) played an important role during the degradation process. Furthermore, the catalyst demonstrated a superb recovery as well as high stability over five cyclic runs of reuse. In addition, the total organic carbon (TOC) analysis showed over 83% and 85% mineralization for MTN and DZN, respectively. The combined system of TiO2/mag-MOF(Cu)/Vis also exhibited a great level of efficiency and feasibility in the treatment of tap water and treated wastewater samples. It is concluded that TiO2/mag-MOF(Cu) could be used as an excellent catalyst for the photodegradation of MTN and DZN in aqueous solution.

Nitrogen-Doped Titanium Carbide (Ti3 C2 Tx ) MXene Nanosheet Stack For Long-Term Stability and Efficacy in Au and Ag Recovery

The development of efficient adsorbents for the practical recovery of precious metals from electronic waste is vital to advanced energy/environment industries. Ti3 C2 Tx MXene-based materials are promising adsorbents for aqueous environments; however, the highly defective and super hydrophilic nature of the MXene surface hinders its practical applications. Here, we report that nitrogen-doped MXene (N-MXene) nanosheet stacks, prepared via high-energy planetary ball milling under N2 purging, exhibited a long-term stable and excellent recovery capability for Au and Ag ions via the nitrogenation of defective vacancies. Notably, these microscale nanosheets could facilitate the sustainable production of Au and Ag from secondary sources, exhibiting a high recovery rate and capability (1198 mg g-1 for Au and 1528 mg g-1 for Ag), long-term stable storability (21 d), and high selectivity (Kd of 1.67 × 106 for Au and 2.07 × 107 for Ag). Furthermore, the reversible redox chemistry of N-MXene facilitated its repeated use in adsorption/desorption cycles.

Eco-Friendly Recycling of Lithium Batteries for Extraction of High-Purity Metals

The significant increase in lithium batteries consumption produces a significant quantity of discarded lithium-ion batteries (LIBs). On the one hand, the shortage of high-grade ores leads to the necessity of processing low-grade ores, which contain a low percentage of valuable metals in comparison to the discarded LIBs that contain a high percentage of these metals, which enhances the processing of the discarded LIBs. On the other hand, the processing of discarded LIBs reduces the negative environmental effects that result from their storage and the harmful elements contained in their composition. Hence, the current study aims at developing cost-effective and ecofriendly technology for cobalt and lithium metal ion recovery based on discarded LIBs. A novel synthesized solid-phase adsorbent (TZAB) was utilized for the selective removal of cobalt from synthetic solutions and spent LIBs. The synthesized TZAB adsorbent was characterized by using 13C-NMR, GC-MS, FT-IR, 1H-NMR, and TGA. The factors affecting the adsorption of cobalt and lithium ions from synthetic solutions and spent LIBs, including the sorbent dose, pH, contact time, temperature, and cobalt concentration were investigated. The conditions surrounding the recovery of cobalt and lithium from processing discarded LIBs, were investigated to optimize the maximum recovery. The Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were used to study the kinetics of the adsorption process. The obtained results showed that high-purity CoC₂O₄ and Li₃PO₄ were obtained with a purity of 95% and 98.3% and a percent recovery of 93.48% and 95.76%, respectively. The maximum recovery of Co(II) from synthetic solutions was obtained at C₀ = 500 mg·L^-1, dose of 0.08 g, pH 7.5, T = 25 °C, and reaction time = 90 min. The collected data from Langmuir's isotherm and the adsorption processes of Co agree with the data predicted by the D-R isotherm models, which shows that the adsorption of Co(II) onto the TZAB seems to be chemisorption, and the results agree with the Langmuir and D-R isotherm models.

Analysis of environmental sustainability of e-waste in developing countries - a case study from Pakistan

The electronic waste generation rate is increasing drastically at a rate of 3 to 5% per year in developing countries. The aim of this study is to analyze the environmental sustainability and economic benefits of such e-waste management in the developing economies like Pakistan. The life cycle assessment (LCA) method has been employed for streamlined impact analysis of the end-of-life processing of e-waste focusing mainly on laptop computers and liquid crystal display (LCD) desktop computers in Pakistan. The method of cumulative exergy extraction from the natural environment (CEENE) has also been deployed for the relative assessment of resources' consumption of e-waste recycling versus landfilling scenario. The determined impact scores are 1.79E + 03 kg CO₂ eq., 7.19E-07 kg CFC-11 eq., 1.02E + 03 kg 1,4-DCB, 7.13E + 01 kg 1,4-DCB, and 3.41E-03 kg Cu eq. in climate change potential, stratospheric ozone depletion, ecotoxicity potential, human noncarcinogenic potential, and mineral resource depletion impact categories, respectively. The results of CEENE analysis reveal that approximately 80% of the impact on natural resources is reduced by the efficient recycling of e-waste. The comparative assessment of respective scores for current and target material weight recovery (MWR) indicators represented that by increasing the MWR indicator by 33.8% for laptop computers and by 27.2% for LCD computers, the country will achieve an annual economic benefit of US $191.56 million. This is greatly significant for a transitional shift towards e-waste revalorization while realizing the objectives of sustainable resource consumption. Innovative improvement measures ensuring economically feasible, energy-efficient, and environment friendly waste collection, treatment, and recycling practices present an invaluable opportunity for developing countries.

Assessment of precious metals positioning in waste printed circuit boards and the economic benefits of recycling

In this study, the distribution of precious metals in waste printed circuit boards was investigated and the economic value of recycling was assessed. Contacts of pins, slots, interfaces and the board surface in waste printed circuit boards were analyzed, and three types of precious metals were detected. The content of gold, silver and palladium ranged from 179.86 mg/kg to 3694.51 mg/kg, 809 mg/kg to 12320.51 mg/kg and 96.25 mg/kg to 117.49 mg/kg, respectively. Gold was distributed wildly in contacts of many slots and all interfaces, while contacts of only two interfaces (the cable and USB) contained palladium. The highest content of Au was found in contacts of the cable. Silver mainly concentrated on pins (metal foil contacts) of electronic components and its highest content was found in microchips. The economic value of recyclable precious metals in 1 t waste printed circuit boards was up to 2292.94 dollars, of which Au contributed 98%. This study indicates the prominent economic benefits of precious metal recovery from waste printed circuit boards. Moreover, the scientific information provide guidance for the directional and accurate recovery of precious metals from waste printed circuit boards.

Removal of Bromine from the non-metallic fraction in printed circuit board via its Co-pyrolysis with alumina

The effectiveness of a recycling approach of the printed circuit board (PCBs), and, thus, the quality of polymeric constituents, primarily rests on the capacity to eliminate the bromine content (mainly as HBr). HBr is emitted in appreciable quantities during thermal decomposition of PCB-contained brominated flame retardants (BFRs). The highly corrosive, yet relatively reactive HBr, renders recovery of bromine-free hydrocarbons streams from brominated polymers in PCBs very challenging. Via combined experimental and theoretical frameworks, this study explores the potential of deploying alumina (Al₂O₃) as a debromination agent of Br-containing hydrocarbon fractions in PCBs. A consensus from a wide array of characterization techniques utilized herein (ICP-OES, IC, XRD, FTIR, SEM-EDX, and TGA) clearly demonstrates the transformation of alumina upon its co-pyrolysis with the non-metallic fractions of PCBs, into aluminum bromides and oxy-bromides. ICP-OES measurements disclose the presence of high concentration of Cu in the non-metallic fraction of PCB, along with minor levels of selected valuable metals. Likewise, elemental ionic analysis by IC demonstrates an elevated concentration of bromine in washed alumina-PCBs pyrolysates, especially at 500 °C. The Coats-Redfern model facilitates the derivation of thermo-kinetic parameters underpinning the thermal degradation of alumina-PCB mixtures. Density functional theory calculations (DFT) establish an accessible reaction pathway for the HBr uptake by the alumina surface, thus elucidating chemical reactions governing the observed alumina debromination activity. Findings from this study illustrate the capacity of alumina as a HBr fixation agent during the thermal treatment of e-waste.

Novel trends in the thermo-chemical recycling of plastics from WEEE containing brominated flame retardants

The amount of plastics from waste electric and electronic equipment (WEEE) has enormously increased nowadays, due to the rapid expansion and consumption of electronic devices and their short lifespan. This, in combination with their non-biodegradability, led to the need to explore environmentally friendly solutions for their safe disposal. One main obstacle when recycling plastics from WEEE is that they usually comprise harmful additives such as brominated flame retardants (BFRs) that need to be removed before or during their recycling. This paper reviews existing techniques for the recycling of plastics from WEEE and focuses specifically on the advantages, disadvantages, and challenges of pyrolysis as an environmentally friendly method for the production of value-added materials (monomers, hydrocarbons, phenols, etc.). Current technological trends available for the recycling of plastics containing brominated flame retardants are reviewed in an attempt to provide insights for future research on the sustainable management of plastics from WEEE. Emphasis is given on conventional pyrolysis, where a pretreatment step for the debromination of products is applied. This is required since brominated compounds treated at high temperatures may result in the production of harmful to health compounds such as dioxins. All current pretreatment methods (solvent extraction, supercritical fluid technology, etc.) are presented and compared in detail. Co-pyrolysis is also investigated, as it seems to be a very interesting approach, since no catalysts or solvents are used, and at the same time, more plastic wastes can be consumed as feedstock. Furthermore, catalytic pyrolysis along with key parameters, such as the type of the catalyst or pyrolysis temperature, are fully analyzed. Catalysts affect the products' distribution and enhance the removal of bromine from pyrolysis oils. Finally, an emerging technique, that of microwave-assisted pyrolysis, is also highlighted, as it offers many advantages over conventional pyrolysis. Of course, there are some impediments, such as the operational costs or other difficulties as regards the industrial implementation of the mentioned techniques that need to be overcome through future works.

Influence of Electrolyte Impurities from E-Waste Electrorefining on Copper Extraction Recovery

In order to reflect possible issues in future sole e-waste processing, an electrolyte of complex chemical composition reflecting system of sole e-waste processing was obtained by following a specially designed pyro-electrometallurgical method. The obtained non-standard electrolyte was further used for the purpose of comprehensive metal interference evaluation on the copper solvent extraction (SX) process. Optimization of the process included a variation of several process parameters, allowing determination of the effect of the most abundant and potentially the most influential impurities (Ni, Sn, Fe, and Zn) and 14 other trace elements. Moreover, comparing three commercial extractants of different active chelating groups, it was determined that branched aldoxime reagent is favorable for Cu extraction from the chemically complex system, as can be expected in future e-waste recycling. The results of this study showed that, under optimal conditions of 20 vol.% extractant concentration, feed pH 1.5, O/A ratio 3, and 10-min phase contact time, 88.1% of one stage Cu extraction was achieved. Co-extraction of the Fe, Zn, Ni, and Sn was under 8%, while Pb and trace elements were negligible. Optimal conditions (H2SO4 180 g/L, O/A = 2, and contact time 5 min) enabled 95.3% Cu stripping and under 6% of the most influential impurities. In addition, an impurity monitoring and distribution methodology enabled a better understanding and design of the process for the more efficient valorization of metals from e-waste.

Urban mining of obsolete computers by manual dismantling and waste printed circuit boards by chemical leaching and toxicity assessment of its waste residues

Waste residues and acidic effluents (post-processing of E-waste) released into the local surroundings cause perilous environmental threats and potential risks to human health. Only limited research and information are available toward the sustainable management of waste residues generated post resource recovery of E-waste components. In the present study, the manual processing of obsolete computer (keyboard, monitor, CPU, and mouse) and chemical leaching of waste printed circuit boards (WPCBs) (motherboard, hard drive, DVD drive, and power supply) were performed for urban mining. The toxicity characteristics of typical pollutants in the residues of the WPCBs (post chemical leaching) were studied by toxicity characteristics leaching procedure (TCLP) test. Manual dismantling techniques resulted in an efficient urban mining concept with an overall average profit estimation of INR 2513.73/US$ 34.59. The chemical leaching of WPCBs showed a high concentration of metal leaching like Cu (229662 ± 575.3 mg/kg) and Pb (36785.67 ± 13.07 mg/kg) in the motherboard after stripping epoxy coating. The toxicity test revealed that the concentration of Cu (245.746 ± 0.016 mg/l) in the treated waste residue and Cu (430.746 ± 0.0015 mg/l) and Pb (182.09 ± 0.0035 mg/l) in the non-treated waste residue exceeded the threshold limit. The concentrations of other elements As, Cd, Co, Cr, Ag, Mn, Zn, Ni, Fe, Se, and In were within the permissible limit. Hence, the waste residue stands non-hazardous except Cu and Pb. Stripping out the epoxy coating of WPCBs enhances the metal leaching concentrations. The study highlighted that efficient and appropriate E-waste urban mining has immense potential in tracing the waste scrap into secondary resources. This study also emphasized that the final processed waste residue (left unattended or discarded due to lack of appropriate skill and technology) can be taken into consideration and exploited for value-added materials.

Impact of Grinding of Printed Circuit Boards on the Efficiency of Metal Recovery by Means of Electrostatic Separation

This paper analyses the impact of the method of grinding printed circuit boards (PCBs) in a knife mill on the efficiency and purity of products obtained during electrostatic separation. The separated metals and plastics and ceramics can be used as secondary raw materials. This is in line with the principle of circular economy. Three different screen perforations were used in the mill to obtain different sizes of ground grains. Moreover, the effect of cooling the feed to cryogenic temperature on the final products of separation was investigated. The level of contamination of the concentrate, intermediate, and waste obtained as a result of the application of fixed, determined electrostatic separation parameters was assessed using ICP-AES, SEM–EDS, XRD, and microscopic analysis as well as specific density. The yields of grain classes obtained from grinding in a knife mill were tested through sieve analysis and by using a particle size analyser. The test results indicate that using a knife mill with a 1 mm screen perforation along with cooling the feed to cryogenic temperature significantly improves the efficiency of the process. The grinding products were characterised by the highest release level of the useful substance—metals in the free state. The purity of the concentrate and waste obtained from electrostatic separation was satisfactory, and the content of the intermediate, in which conglomerates of solid metal–plastic connections were present, was very low. The yield of concentrate and waste amounted to 26.2% and 71.0%, respectively. Their purity, reflected in the content of the identified metals (valuable metals), was at the level of 93.3% and 0.5%, respectively. In order to achieve effective recovery of metals from PCBs by means of electrostatic separation, one should strive to obtain a feed composed of grains <1000 μm and, optimally, <800 μm.

Environmentally friendly approach for the recovery of metallic fraction from waste printed circuit boards using pyrolysis and ultrasonication

Electronic waste (e-waste) with an annual growth rate of 3-5% is one of the fastest-growing waste streams. The unregulated accumulation and improper recycling can cause grave hazards to human beings and the environment. On the contrary, e-waste can be considered as a secondary source of metals and energy due to its high metal content and polymeric material. Thus, the present study demonstrates technology for the metallic fraction recovery and the production of valuable gases from e-waste. The process involves pyrolysis at a temperature range of 200 °C-600 °C in a fixed bed setup for 10-60 min. Under optimized operating conditions, 35 wt% combustible gases and 60 wt% solid product were obtained at a pyrolysis temperature of 400 °C in 20 min. The gaseous product consisted of CH₄, H₂, CO and CO₂, having the heating value 28 MJ/kg whereas, the solid product is a mixture of metals and other solid residue material. Treatment of the solid product using an ultrasonication process resulted in around 90 wt% recovery of metallic fraction, thereby leaving behind solid residue. Moreover, the transfer of precious metals (Au, Ag, Pd and Pt) was nearly 100% to the metallic fraction. This process combines mild temperature pyrolysis and ultrasonication process to provide a solution for efficient management of e-waste, metallic fraction recovery and valuable gases production.

Copper and Antimony Recovery from Electronic Waste by Hydrometallurgical and Electrochemical Techniques

A strategy for the efficient recovery of highly pure copper and antimony metals from electronic waste (e-waste) was implemented by the combination of hydrometallurgical and electrochemical processes. The focus is on copper recovery as the main component in the leached solution, whereas the antimony recovery process was established as a purification step in order to achieve a highly pure copper deposit. The strategy includes mechanical methods to reduce the size of the wasted printed circuit boards to enhance the efficiency of antimony and copper lixiviation via ferric chloride in acidic media (0.5 M HCl) followed by an electrowinning process. In order to establish the best parameters for copper electrowinning, the leached solution was characterized by cyclic voltammetry and cathodic polarization. Then, an electrochemical reactor with a rotating cylinder electrode was used to evaluate the copper concentration decay, the cathodic current efficiency, the specific energy consumption, and mass-transfer coefficient. Furthermore, antimony was recovered via precipitation by a pH modification in accordance with the Pourbaix diagram. Under this methodology, two valuable products from the e-waste were recovered: a 96 wt % pure copper deposit and 81 wt % pure antimony precipitate. The strategy for recovery of other metal ions, such as lead, present in the e-waste at high concentrations will be reported in further works.

Recovery of palladium and silver from waste multilayer ceramic capacitors by eutectic capture process of copper and mechanism analysis

Recycling waste multilayer ceramic capacitors (MLCCs) is significant for environmental protection and resource recovery, which contain rich precious metals including palladium and silver. The existing recycling methods have many shortcomings such as environmental pollution, low recovery efficiency and low purity of precious metals. In view of the special structure of MLCCs and low content of precious metals per unit mass, a novel approach of enrichment for recovering palladium and silver from waste MLCCs by eutectic capture process of copper was proposed, in which process precious metals were separated and enriched for subsequent recovery. The recovery rates of palladium and silver reached 100 % and 87.53 %, respectively under the optimal condition. And the enrichment multiples of palladium and silver were 13.16 and 7.37. The Cu-Pd-Ag alloy was formed in the capture process, of which palladium and copper formed Cu-Pd solid solution, while silver was a separate phase through the analysis of SEM-EDS, XPS and XRD. Besides, the molten residue can be reused to prepare glass-ceramics. Finally, the mechanism was analyzed through thermodynamics, which was divided into two processes: migration of precious metals and alloy formation. This study provides a highly efficient and environmentally friendly method for recycling precious metals from waste MLCCs.

Verification of the hydrostatic weighing system with existing gold purity instruments

Determination of gold bar purity remains one of the most challenging tasks in gold industry. Currently, the existing instruments have a limitation to determine the purity, which in turn have produced inaccurate gold purity measurement. For example, X-ray fluorescence (XRF) technique has a limitation to penetrate the gold bar and XRF was only used to determine the surface purity. Therefore, an improved non-destructive method and precise technique has been developed to determine the gold purity. Gold density measurement can verify the purity of the gold and in this study, the density of gold bar was calculated using a custom made hydrostatic weighing system (HWS). Several measurements of density were carried out for gold bar and tungsten bar. Using HWS, the density of gold bar and tungsten bar were 19.268 g/ml and 19.206 g/ml respectively. The expanded uncertainty was also evaluated and the value was 0.006 g/ml. The new developed HWS method was also verified with existing density measurement instruments where the same density results has been obtained but the existing instruments have produced bigger uncertainty of 0.2 g/ml. Thus, this study demonstrates that the developed HWS is appropriate to be used to measure the density of gold bar accurately. Furthermore, the new developed system of HWS have shown better measurement with smaller uncertainty and hence the improvement in gold bar purity measurement.

Factors influencing the release of potentially toxic elements (PTEs) during thermal processing of electronic waste

The release of potentially toxic elements as airborne fine particulates is a significant environmental risk associated with recycling e-waste. Some of these may redeposit near emission sites or be transported over long distances causing wide-spread pollution. With an aim to identify key factors affecting particulate emissions, we report novel investigations on the adsorptive capture of particulate matter (PM) released during low temperature pyrolysis (600 °C; 15 min) of waste printed circuit boards (PCBs). A significant proportion of the released particulates (5.3 to 37%) were captured by adsorbents located downstream and in close proximity to the emitting source. Data was collected for four different PCBs and three adsorbents: alumina, silica-gel and activated carbon. With sizes ranging from nanoparticles to over 10 µm, adsorbed particulates were present as fines, spheres, oblongs, clusters and larger particles with no specific shape. Of the 24 elements identified initially in waste PCBs, only 14 were detected in released particulates: major PTEs- Zn, Sn, Pb and Cu (up to 400 ppm); minor PTEs- Ni, Mn, Cd, Cr and Ba (up to 10 ppm); trace PTEs- Co, In, Bi, Be and Sb (up to 1 ppm). Key factors influencing the release of PTEs during thermal processing were identified as basic elemental characteristics, densities, melting points, vapor pressures, initial concentrations, local bonding and mechanical strength. These results show that the presence of low melting point/high vapour pressure elements (Zn, Pb, Sn) should be minimised for a significant reduction in PTE emissions during e-waste processing.

On the facile and accurate determination of the Pt content in standard carbon supported Pt fuel cell catalysts

We introduce a new and straight-forward methodology to accurately determine the Pt content in polymer membrane electrolyte fuel cell (PEMFC) catalysts consisting of carbon supported Pt nanoparticles (Pt/C). The method is based on an indirect Pt proof (IPP) consisting of the oxidative removal of the carbon support, the digestion of the Pt in aqua regia followed by a replacement reaction to form Cu ions (CuCl₂). The Pt content is then determined via the Cu-ions with the help a complexometric indicator using a simple titration. The procedure is fast and does not require any expensive equipment. Thus, it can be implemented in any standard chemistry laboratory. The advantages and disadvantages of the IPP method are evaluated in a comparison to alternative methods for the determination of the Pt content in supported catalysts, i.e. inductively coupled plasma mass spectrometry (ICP-MS) and UV/Vis spectroscopy (UV/Vis). It is demonstrated that the IPP method delivers reliable and accurate results and is less influenced than for example ICP-MS by side effects such as excess in nitric acid or organic impurities. Furthermore, during the procedure up to 60% of the Pt material is recovered during the IPP procedure.

A comparative study of the physiological and biochemical properties of tomato (Lycopersicon esculentum M.) and maize (Zea mays L.) under palladium stress

There is great concern about the environmental impact and toxicity of palladium (Pd) because of its widespread use in automotive catalytic converters and other applications. Pd migrates and transforms in the environment and is absorbed by plant roots where it affects plant growth and eventually enters the food chain. Here we explored the effects of Pd on the physicochemical and biochemical characteristics of C3 (tomato) and C4 (maize) plants. We measured physicochemical and biochemical properties, including chlorophyll, protein, soluble sugar, antioxidant enzymes, malondialdehyde, proline, and root activity, in tomato and maize seedlings after cultivation in different concentrations of PdCl₂ solution (0, 0.2, 0.5, and 1 mM) in order to observe how Pd stresses them. Results showed that, with increasing Pd concentration, chlorophyll a and chlorophyll b contents and root activity decreased. Meanwhile, malondialdehyde, proline, protein, and soluble sugar contents increased. After cultivation in 1 mM PdCl₂, the Pd contents in the roots, stems, and leaves of tomato seedlings were 12.389, 1.132, and 0.206 mg/g, respectively. In general, Pd has significant effects on the physiological and biochemical properties of both tomato and maize. Additionally, tomato seedlings were more sensitive to Pd stress, photosynthesis in maize was less inhibited by Pd and the antioxidant capability of maize was stronger. These results indicated that maize (C4 plant) exhibited a higher tolerance to Pd than tomato (C3 plant). Pd migration in tomato was observed and the translocation factor (TF) was calculated. The values of TF_stem/root, TF_leaf/root, TF_leaf/stem, and TF_shoot/root were 0.09, 0.02, 0.18, and 0.11 in tomato seedlings, respectively. Pd accumulated most in the roots, followed in turn by stems, leaves, and only trace amount of Pd was transferred into shoots.

Bioleaching assisted foam fractionation for recovery of gold from the printed circuit boards of discarded cellphone

Present work was focused on recovering gold (Au) from the printed circuit boards (PCBs) of discarded cellphone by bioleaching assisted continuous foam fractionation. First, the cyanide-producing strains of Pseudomonas putida and Bacillus megaterium were co-cultured in order to supply a high cyanide concentration in the nutrient solution for mobilizing Au from waste PCBs (WPCBs). Bioleaching conditions were optimized by using response surface methodology. Under the suitable bioleaching conditions of pH of 10.0, pulp density of 5 g/L and leaching time of 34 h, the Au mobilization percentage was 83.59%. The leaching liquor with an Au concentration of 1.34 mg/L could be used as the feeding solution of continuous foam fractionation after removing solid particles and cell biomass. In order to strengthen foam drainage, a novel internal component of foam fractionation column was developed. Under the suitable operation conditions of CTAB concentration of 0.2 g/L, volumetric air flow rate of 100 mL/min and feed flow rate of 10 mL/min, the enrichment ratio and recovery percentage of Au were 43.62 and 87.46%, respectively. This study is expected to provide an effective strategy to recover Au from WPCBs, and to supplement the depleting natural resources.

Dendritic Nanostructured Waste Copper Wires for High-Energy Alkaline Battery

Rechargeable alkaline batteries (RABs) have received remarkable attention in the past decade for their high energy, low cost, safe operation, facile manufacture, and eco-friendly nature. To date, expensive electrode materials and current collectors were predominantly applied for RABs, which have limited their real-world efficacy. In the present work, we propose a scalable process to utilize electronic waste (e-waste) Cu wires as a cost-effective current collector for high-energy wire-type RABs. Initially, the vertically aligned CuO nanowires were prepared over the waste Cu wires via in situ alkaline corrosion. Then, both atomic-layer-deposited NiO and NiCo-hydroxide were applied to the CuO nanowires to form a uniform dendritic-structured NiCo-hydroxide/NiO/CuO/Cu electrode. When the prepared dendritic-structured electrode was applied to the RAB, it showed excellent electrochemical features, namely high-energy-density (82.42 Wh kg-1), excellent specific capacity (219 mAh g-1), and long-term cycling stability (94% capacity retention over 5000 cycles). The presented approach and material meet the requirements of a cost-effective, abundant, and highly efficient electrode for advanced eco-friendly RABs. More importantly, the present method provides an efficient path to recycle e-waste for value-added energy storage applications.

Soil elemental concentrations, geoaccumulation index, non-carcinogenic and carcinogenic risks in functional areas of an informal e-waste recycling area in Accra, Ghana

This study assesses the distribution, contamination and human health risks of major, minor and trace elements in the topsoil and subsoil of two informal e-waste recycling sites in Accra, Ghana. Metal concentrations in Agbogbloshie exceeded the Dutch Soil intervention values with exceedances of 72%, 57%, 57%, 38%, 16%, 2% for Cu, Zn, Pb, Ba, Cd and As respectively. Metal concentrations in Ashaiman exceeded the Dutch Soil intervention values with exceedances of 62%, 57% and 46% for Cu, Zn and Pb respectively. Geoaccumulation indices indicated that the topsoils of the burn area and dismantling areas of Agbogbloshie e-waste recycling site were strongly contaminated by Pb and uncontaminated by Cr, Fe, As and Ba. Lead (Pb) contributed greatly to non-carcinogenic ingestion hazard quotient for residents living near Agbogbloshie and Ashaiman e-waste recycling sites while arsenic (As) presented carcinogenic risks to children from the dismantling area topsoils. Non-carcinogenic risks from ingestion were significant with children being more susceptible to non-carcinogenic ingestion risks than adults. Non-carcinogenic risks from dermal exposure were negligible. Hazard quotients of Pb for children in burn area topsoils and dismantling area topsoils were 7.4-7.6-fold greater than that for adults. The mean geoaccumulation indices values of Pb and Cu indicated extreme contamination of topsoils with these elements. A "novel environmental assessment tool" based on the Agency for Toxic Substances and Disease Registry (ASTDR) total impact points confirmed Pb and Cu as the most toxic elements.

Development of novel sericin and alginate-based biosorbents for precious metal removal from wastewater

In this study, two novel low water-soluble sericin and alginate-based biosorbents were successfully developed for precious metal removal from wastewater: sericin and alginate particles chemically crosslinked by proantocyanidins (SAPAs) and sericin, alginate and polyvinyl alcohol particles (SAPVA). The proportions of proantocynidins (PAs) or polyvinyl alcohol (PVA) added to sericin (2.5% w/v) and alginate (2.0% w/v) blend were 0.5, 1.5, 2.5 and 3.5% w/v. Among these concentrations, particles produced with 0.5% w/v of PVA or 2.5% w/v of PAs presented the lowest water solubility percentages (3.74 ± 0.05 and 3.56 ± 0.21%, respectively) and the following metallic affinity order: AuCl₄^- > PdCl₄^2- > PtCl₆^2- > Ag⁺. Then, gold biosorption kinetics by SAPAs was evaluated at three gold initial concentrations (72.88, 187.12, and 273.79 mg/L), and its performance was compared to activated carbon adsorbent uptake. The data modeling revealed that the process follows pseudo-first-order kinetics and is mainly controlled by external diffusion. SAPAs before and after gold biosorption (SAPAs-gold) were characterized by scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, optical microscopy, helium pycnometry, mercury porosimetry, N₂ physisorption, and Fourier-transform infrared spectroscopy.

Lab scale optimization and two-step sequential bench scale reactor leaching tests for the chemical dissolution of Cu, Au & Ag from waste electrical and electronic equipment (WEEE)

Regulations force to Waste Electrical and Electronic Equipment (WEEE) management by recycling the materials by safe and suitable methods, due to generating massive amounts of WEEE. This research aims towards extract metals from waste random-access memory (RAM) devices in different solutions. In addition, the effect of different parameters such as reagent concentration, oxidant concentration and solid/liquid ratio were investigated with full factorial experimental design tests and analysis of variance (ANOVA). The results showed that the extraction of gold and silver was 96.81% and 99.02% respectively under the following conditions: concentration of 2% iodine and 3% hydrogen peroxide as oxidizing agent, 5% solid/liquid ratio and leaching period of 2 h. An increase of the hydrogen peroxide concentration increased gold and silver extraction. While about 79.30% silver was found to be extracted using 2 M sulfuric acid, 1.5 M ammonium persulfate, 5% solid/liquid ratio and leaching period of 5 h, 79.43% copper was extracted by using ammonia instead of sulfuric acid under the same conditions. Ammonium persulfate was found to be a good oxidizing agent for sulfuric acid and ammonia leaching, since it provided selective extraction of silver and copper respectively. Two-step sequential bench scale reactor leaching tests were conducted to extract copper (98.73%), gold (99.98%) and silver (96.90%) selectively with high extraction. Two-step leaching approach was concluded as the most appropriate method for selective extraction of targeted metals from waste RAM devices.

A relative risk assessment of the open burning of WEEE

Waste electric and electronic equipment (WEEE) represents a potential secondary source of valuable materials, whose recovery is a growing business activity worldwide. In low-income countries, recycling is carried out under poorly controlled conditions resulting in severe environmental pollution. High concentrations of both metallic and organic pollutants have been confirmed in air, soil, water, and sediments in countries with informal recycling areas. The release of these contaminants into the environment presents a risk to the health of the exposed population that has been widely acknowledged but still needs to be quantified. The aim of this work was to evaluate the relative risk from inhalation associated with the open burning of different kinds of WEEE. The shrinking core model was applied to estimate the concentration of the metals which would be released into the environment during the incineration of different types of WEEE. In addition, the potential generation of dioxins during the same informal practice was estimated, based on the plastic content of the WEEE. The results provided for the first time a comparative analysis of the risk posed from the open burning of WEEE components, proposing a methodology to address the absolute risk assessment to workers from the informal recycling of WEEE.

Determination of Metal Content of Waste Mobile Phones and Estimation of Their Recovery Potential in Turkey

Waste mobile phones constitute one of the fastest growing Waste Electrical and Electronic Equipment (WEEE) types all over the world due to technological innovations and shortening of their life span. They contain a complex mix of various materials, such as basic metals, precious metals and rare earth elements and represent an important secondary raw metal source. The main objectives of this study were to characterize the metal concentration of waste mobile phones by optimizing the inductively coupled plasma optical emission spectrometer (ICP-OES) operation parameters and estimate the metal recovery potential of waste mobile phones in Turkey. Therefore, selected mobile phone samples collected from a recycling center in Turkey were analyzed to determine their metal concentrations. Then, the theoretical recovery potentials of precious and rare earth metals from waste mobile phones were estimated for Turkey. The analytical methods optimized in this study can help further research activities to obtain comprehensive data for determination of the critical metals (precious metals and rare earth elements) in WEEE samples so that proper recycling and recovery strategies can be selected and implemented.

Separation of metals from metal-rich particles of crushed waste printed circuit boards by low-pressure filtration

In recent years, recovery of metals from electronic waste (e-waste) within China has become increasingly important due to potential supply risk of strategic raw material and environmental concerns. Printed circuit boards (PCBs) contain lots of valuable metals together with plenty of hazardous materials, which are considered both an attractive secondary resource and an environmental contaminant. Pressure filtration is an effective and environmentally friendly method for separating and recycling comminuted PCBs. Present work is focused on the recovery of metals from PCBs by low-pressure filtration separation. A two-stage separation process was adopted to selectively recover Pb-Sn and Cu alloys at different temperatures. The results showed that the temperature and pressure had great influence on the recovery of metals in the separation process. After the two-stage separation process, the total recoveries of Pb, Sn, Cu and Zn were 79.96%, 89.91%, 88.80% and 68.57% respectively, when the temperature is 1350 °C and the pressure is 0.30 MPa. This is a high-efficiency, short-flow, clean-production, and environmental-friendliness that can improve the recovery of metals and realize the reuse of waste resources.

Influence of scope definition in recycling rate calculation for European e-waste extended producer responsibility

Efficiency indicators have been frequently used to assess end-of-life chain performance, mostly. In terms of the percentage of mass sent to re-use, recycling, and/or energy recovery facilities. While legislation gives a standard definition for recycling and recovery rates, stakeholders sometimes redefine them to better fit their own scopes and objectives. Therefore, to accurately interpret the results of an efficiency indicator, during a decision-making process, it's necessary to fully understand the scope definition used to calculate it. This work discusses the influence of scope definition when establishing performance rates. It does this by introducing further alternative scope definitions and comparing them to those defined by legislation and stakeholders. As a case study, the proposed complementary scopes are applied to the recycling chain of flat panel displays in France.

Concentration of precious metals from waste printed circuit boards using supergravity separation

Printed circuit boards (PCBs) comprise valuable metals, precious metals, and hazardous materials. Thus, they are considered both attractive secondary sources of metals and environmental pollutants. This study is based on the selective separation of Pb-Sn, Sn-Cu, and Cu-Zn alloys, where supergravity separation was used to concentrate precious metals (i.e., Ag, Au, and Pd) from PCBs in Cu-Zn alloy and final residue. The temperature and gravity coefficient were found to have great influence on the concentration of precious metals in said alloy and residue. At the optimized temperature of 1300 °C, gravity coefficient of 1000, and separation time of 5 min, the Ag, Au, and Pd contents in the Cu-Zn alloy increased by 1.65, 2.05, and 1.54 times, respectively, compared to their concentrations in the original PCBs, while those in the final residue increased by 0.63, 1.02, and 2.62 times, respectively. By combining an appropriate hydrometallurgical process with the present supergravity separation and concentration of precious metals, this clean and efficient process provides a new pathway to recycle valuable metals and prevent environmental pollution by PCBs.

Disentanglement of random access memory cards to regenerate copper foil: A novel thermo-electrical approach

This paper reports the development of a novel process combining thermal and electrical treatments, which are optimised to provide efficient recovery of copper foil from Random Access Memory cards (RAMs). A primary thermal transformation at 900 °C facilitates a highly efficient recovery of copper foils from RAMs during the secondary processing in the electrical fragmenter, using only 10 pulses at 150 kV. The process yield was 98% and inductively coupled plasma (ICP) analysis showed that the copper foils had 98% purity. X-ray diffraction (XRD) confirmed the presence of copper in a crystalline face-centred cubic (FCC) form. Scanning electron microscopy (SEM) - energy dispersive spectroscopy (EDS) analysis of the foils assisted in understanding the underlying mechanism of electrical separation. Transmission electron microscopy (TEM) gave a new perspective on the regeneration of copper foils wherein new copper grains depicted a ribbon like growth pattern. The copper foils had an electrical conductivity similar to that of commercially available pure copper sheets. Thus, the mechanism of thermo-electrical transformation was studied in detail and regenerated copper foils of high electrical conductivity were afforded from end-of-life RAMs.

Diagnosis and ecotoxicological risk assessment of 49 elements in sludge from wastewater treatment plants of Chongqing and Xiamen cities, China

Limited information about the sludge quality is a major constraint for its usage and proper disposal. This study investigated the occurrence of 49 elements in sludge from 11 wastewater treatment plants (WWTPs) in Chongqing and Xiamen cities of China. The concentration of 46-detected elements ranged from 16.2 μg kg^-1 (Pt) to 55.0 g kg^-1 (Al) on dry solid basis in the sludge. The enrichment factor of most of the elements was > 1.5, indicating their possible anthropogenic origin. The precious metals had considerably higher enrichment factor ranging from 56.3 to 200,000. Principal component analysis clustered the samples from Chongqing and Xiamen separately to suggest strong spatial variations. Contamination factor, pollution loading index, and integrated pollution degree were calculated to evaluate the elemental pollution risk. The pollution loading index indicated unpolluted to highly polluted levels of the elements in the sludge. In addition, results from the ecotoxicological risk index showed an individual low to very high ecotoxicological risk posed by eight metal(loid)s (As, Cd, Cr, Cu, Mn, Ni, Pb, and Zn) in the WWTPs.

Zinc Oxide Nanoparticles from Waste Zn-C Battery via Thermal Route: Characterization and Properties

Disposable batteries are becoming the primary sources of powering day-to-day gadgets and consequently contributing to e-waste generation. The emerging e-waste worldwide is creating concern regarding environmental and health issues. Therefore, a sustainable recycling approach of spent batteries has become a critical focus. This study reports the detail characterization and properties of ZnO nanoparticles recovered from spent Zn-C batteries via a facile thermal synthesis route. ZnO nanoparticles are used in many applications including energy storage, gas sensors, optoelectronics, etc. due to the exceptional physical and optical properties. A thermal treatment at 900 °C under an inert atmosphere of argon was applied to synthesize ZnO nanoparticles from a spent Zn-C battery using a horizontal quartz tube furnace. X-ray diffraction (XRD), selected area electron diffraction (SAED) and X-ray photoelectron spectroscopy (XPS) results confirmed the formation of crystalline ZnO nanoparticles. Field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) analysis confirmed that the size of synthesised ZnO particles were less than 50 nm and mainly composed of sphere shaped nanoparticles. Synthesized ZnO exhibited BET surface area of 9.2629 m²/g and showed absorption of light in the UV region. Excitation of ZnO by UV light showed photoluminescence in the visible range. This study will create an opportunity for potential applications of ZnO nanoparticles from spent batteries and will benefit the environment by reducing the volume of e-waste in landfills.

Concentration of rare earth elements during high temperature pyrolysis of waste printed circuit boards

An in-depth investigation was carried out on the recovery of rare earth elements (REEs) from a variety of waste printed circuit boards (PCBs). High temperature pyrolysis was carried out at 850 °C for 15 min using horizontal resistance and thermal plasma furnaces with different levels of turbulence. The concentration of REEs in key pyrolysis residues, namely, copper rich red metallic fraction, lead/tin rich white metallic fraction and slag rich carbonaceous residues, were determined using ICP analysis. Most of the REEs were found concentrated in the carbonaceous residue with negligible levels of REEs recovered in the two metallic fractions. Most of the recovered REEs showed a high affinity towards to refractory oxides silica and alumina, and little affinity towards metals Cu, Pb and Sn. The yield of REEs was significantly higher from the plasma furnace indicating the important role of turbulence in the dissociation & subsequent diffusion of REEs during pyrolysis. While La, Pr, Sm and Y required turbulent conditions for their recovery, Nd, Gd, Ce and Dy were relatively easy to dissociate and extract from the waste. Significant amounts of REEs could thus be recovered from waste PCBs as concentrated recyclates for further processing and extraction of individual rare earths. This study has shown that PCBs could prove to be a valuable urban mining resource of REEs. The recovery of REEs, in addition to precious and other metals, could play an important role towards enhancing the economic and environmental sustainability of e-waste recycling.

Antimicrobial copper nanoparticles synthesized from waste printed circuit boards using advanced chemical technology

Waste Printed Circuit Boards (WPCBs) were classified as one of the most important resources for urban mining containing high purity Copper (Cu) and other valuable materials. Recently, a dissolution recycling approach enhanced by ultrasonic treatment succeeded in the liberation of Cu foils from WPCBs as received. This research aims to synthesize Copper Nanoparticles (Cu-NPs) from the recovered Cu by using an advanced chemistry approach to obtain nano-product with high added value taking into consideration environmental risks. The experiments were carried out on the Cu foils recovered from the three types of WPCBs with different purity of Cu (Motherboard, Video Card, and Random Access Memory (RAM)). The synthesis process was performed in two stages: (a) preparation of Copper (II) Sulfate aqueous solutions from the recovered Cu and (b) chemical reduction of solutions for synthesis of Cu-NPs by using Native Cyclodextrins (NCDs), particularly ß-NCD as stabilizers. The efficiency of the developed approach for raw material of different purity was assessed and the final yield and the estimated recovery cost of synthesized Cu-NPs were calculated with high accuracy as well as the properties of the synthesized Cu-NPs. The obtained Cu-NPs were examined using SEM-EDS, TEM, XRD, Raman Spectroscopy, and TGA. To maximize the potential biomedical application benefits, the antibacterial activity of Cu-NPs was investigated by the standard microdilution method for E. coli, P. aeruginosa, and S. aureus bacterial cultures. The results showed that the produced Cu-NPs had an average size of 7 nm and yield 90%, while the preparation costs were 6 times lower in comparison to the commercial counterparts. In addition, the results indicated that the synthesized Cu-NPs from RAM sample had a good antimicrobial action.

High temperature investigations on optimising the recovery of copper from waste printed circuit boards

High temperature pyrolysis investigations were carried out on waste printed circuit boards (PCBs) in the temperature range 800-1000°C under inert conditions, with an aim to determine optimal operating conditions for the recovery of copper. Pyrolysis residues were characterized using ICP-OES analysis, SEM/EDS and XRD investigations. Copper foils were successfully recovered after pyrolysis at 800°C for 10-20 min; the levels of Pb and Sn present were found to be quite low and these were generally present near the foil edges. The relative proportions of Pb and Sn became progressively higher at longer heating times due to enhanced diffusion of these molten metals in solid copper. While a similar behaviour was observed at 900°C, the pyrolysis at 1000°C resulted in copper forming Cu-Sn-Pb alloys; copper foils could no longer be recovered. Optimal conditions were identified for the direct recovery of copper from waste PCBs with minimal processing. This approach is expected to make significant contributions towards enhancing material recovery, process efficiency and the environmental sustainability of recycling e-waste. Pyrolysis at lower temperatures, short heating times, coupled with reductions in process steps are expected to significantly reduce energy consumption and pollution associated with the handling and processing of waste PCBs.

En masse pyrolysis of flexible printed circuit board wastes quantitatively yielding environmental resources

This paper reports the recycling of flexible printed circuit board (FPCB) waste through carbonization of polyimide by dual pyrolysis processes. The organic matter was recovered as pyrolyzed oil at low temperatures, while valuable metals and polyimide-derived carbon were effectively recovered through secondary high temperature pyrolysis. The major component of organics extracted from FPCB waste comprised of epoxy resins were identified as pyrolysis oils containing bisphenol-A. The valuable metals (Cu, Ni, Ag, Sn, Au, Pd) in waste FPCB were recovered as granular shape and quantitatively analyzed via ICP-OES. In attempt to produce carbonaceous material with increased degree of graphitization at low heat-treatment conditions, the catalytic effect of transition metals within FPCB waste was investigated for the efficient carbonization of polyimide films. The morphology of the carbon powder was observed by scanning electron microscopy and graphitic carbonization was investigated with X-ray analysis. The protocols outlined in this study may allow for propitious opportunities to salvage both organic and inorganic materials from FPCB waste products for a sustainable future.

Adsorption of PtCl62− from Hydrochloric Acid Solution by Chemically Modified Lignin Based on Rice Straw

A novel adsorbent with the properties of selective adsorption based on rice straw was used to adsorb PtCl62− from hydrochloric acid solution by batch sorption. Many influencing factors for PtCl62− adsorption, such as initial concentration of PtCl62−, adsorption time, and concentration of hydrochloric acid, were optimized. The results suggested that the saturation adsorption capacity of PtCl62− was 218.8mgg−1 and the equilibrium adsorption time was 120min. The adsorbent had excellent selectivity on PtCl62− when the concentration of hydrochloric acid was lower than 0.5molL−1. The adsorption fitted well with the Langmuir isotherm model and pseudo-second-order kinetics model. The adsorption mechanism was investigated by FT-IR and X-ray photoelectron spectroscopy analyses and it indicated that PtIV was reduced to PtII by hydroxy groups and then coordinated with N through ion exchange between Cl− and PtCl42−.

Selective recovery of silver from waste low-temperature co-fired ceramic and valorization through silver nanoparticle synthesis

Considering the value of silver metal and silver nanoparticles, the waste generated during manufacturing of low temperature co-fired ceramic (LTCC) were recycled through the simple yet cost effective process by chemical-metallurgy. Followed by leaching optimization, silver was selectively recovered through precipitation. The precipitated silver chloride was valorized though silver nanoparticle synthesis by a simple one-pot greener synthesis route. Through leaching-precipitation optimization, quantitative selective recovery of silver chloride was achieved, followed by homogeneous pure silver nanoparticle about 100nm size were synthesized. The reported recycling process is a simple process, versatile, easy to implement, requires minimum facilities and no specialty chemicals, through which semiconductor manufacturing industry can treat the waste generated during manufacturing of LTCC and reutilize the valorized silver nanoparticles in manufacturing in a close loop process. Our reported process can address issues like; (i) waste disposal, as well as value-added silver recovery, (ii) brings back the material to production stream and address the circular economy, and (iii) can be part of lower the futuristic carbon economy and cradle-to-cradle technology management, simultaneously.

Selective Recovery of Gold from Electronic Waste Using 3D-Printed Scavenger

Around 10% of the worldwide annual production of gold is used for manufacturing of electronic devices. According to the European Commission, waste electric and electronic equipment is the fastest growing waste stream in the European Union. This has generated the need for an effective method to recover gold from electronic waste. Here, we report a simple, effective, and highly selective nylon-12-based three-dimensional (3D)-printed scavenger objects for gold recovery directly from an aqua regia extract of a printed circuit board waste. Using the easy to handle and reusable 3D-printed meshes or columns, gold can be selectively captured both in a batch and continuous flow processes by dipping the scavenger into the solution or passing the gold-containing solution through the column. The possibility to optimize the shape, size, and flow properties of scavenger objects with 3D printing enables the gold scavengers to match the requirements of any processing plants.

Bioleaching of Gold and Silver from Waste Printed Circuit Boards by Pseudomonas balearica SAE1 Isolated from an e-Waste Recycling Facility

Indigenous bacterial strain Pseudomonas balearica SAE1, tolerant to e-waste toxicity was isolated from an e-waste recycling facility Exigo Recycling Pvt. Ltd., India. Toxicity tolerance of bacterial strain was analyzed using crushed (particle size ≤150 µm) waste computer printed circuit boards (PCBs)/liter (L) of culture medium. The EC₅₀ value for SAE1 was 325.7 g/L of the e-waste pulp density. Two-step bioleaching was then applied to achieve the dissolution of gold (Au) and silver (Ag) from the e-waste. To maximize precious metal dissolution, factors including pulp density, glycine concentration, pH level, and temperature were optimized. The optimization resulted in 68.5 and 33.8% of Au and Ag dissolution, respectively, at a pH of 9.0, a pulp density of 10 g/L, a temperature of 30 °C, and a glycine concentration of 5 g/L. This is the first study of Au and Ag bioleaching using indigenous e-waste bacteria and its analysis to determine e-waste toxicity tolerance.