Structural, physicochemical and microbial properties of flocs and biofilms in integrated fixed-film activated sludge (IFFAS) systems

Biofilm formation and microbial interactions in moving bed-biofilm reactors treating wastewater containing pharmaceuticals and personal care products: A review

The risk of pharmaceuticals and personal care products (PPCPs) has been paid more attention after the outbreak of COVID-19, threatening the ecology and human health resulted from the massive use of drugs and disinfectants. Wastewater treatment plants are considered the final stop to restrict PPCPs from wide spreading into the environment, but the performance of conventional treatment is limited due to their concentrations and characteristics. Previous studies have shown the unreplaceable capability of moving bed-biofilm reactor (MBBR) as a cost-effective method with layered microbial structure for treating wastewater even with toxic compounds. The biofilm community and microbial interactions are essential for the MBBR process in completely degrading or converting types of PPCPs to secondary metabolites, which still need further investigation. This review starts with discussing the initiation of MBBR formation and its influencing parameters according to the research on MBBRs in the recent years. Then the efficiency of MBBRs and the response of biofilm after exposure to PPCPs are further addressed, followed by the bottlenecks proposed in this field. Some critical approaches are also recommended for mitigating the deficiencies of MBBRs based on the recently published publications to reduce the environmental risk of PPCPs. Finally, this review provides fundamental information on PPCPs removal by MBBRs with the main focus on microbial interactions, promoting the MBBRs to practical application in the real world of wastewater treatment.

Sludge biolysis pretreatment to reduce antibiotic resistance genes (ARGs): Insight into the relationship between potential ARGs hosts and BALOs' preferred prey

As an important reservoir of antibiotic resistance genes (ARGs), the sludge discharged from wastewater treatment plants is the key intermediate for ARG transport into the environment. Bdellovibrio-and-like organisms (BALOs) are predatory bacteria that are expected to attack antibiotic-resistant bacteria (ARB). In this study, the screened BALOs (C3 & D15) were mixed with the sludge for biolysis to achieve the satisfying removal efficiencies of six tet genes, two sul genes, and one mobile genetic element (intl 1). Among them, tet(Q) demonstrated the highest reduction rate in relative abundance at 87.3 ± 1.0 %, while tet(X) displayed the lowest of 11.7 ± 0.2 %. The microorganisms, including Longilinea, Methanobacterium, Acetobacterium, Sulfurimonas, allobaculum, Gaiella, AAP99, Ellin6067, Rhodoferax, Ferruginibacter and Thermomonas, were expected to play a dual role in the reduction of ARGs by serving as ARB and BALOs' preferred prey. Meanwhile, BALOs consortium improved ARGs reduction efficiency via the expansion of the prey profile. Additionally, BALOs decreased the relative abundance of not only pathogens (Shinella, Rickettsia, Burkholderia, Acinetobacter, Aeromonas, Clostridium, Klebsiella and Pseudomonas), but also the ARGs' host pathogens (Mycobacterium, Plesiocystis, Burkholderia, and Bacteroides). Therefore, the application of BALOs for sludge biolysis are promising to decrease the sludge's public health risks via limiting the spread of ARGs and pathogens into the environment.

Occurrence and mechanism of sulfamethoxazole in alginate-like extracellular polymers from excess sludge

The recovery of biopolymers, particularly alginate-like extracellular polymers, from municipal sludge represents a promising step toward sustainable sludge treatment practices. Originating from wastewater plants in complexly polluted environments, alginate-like extracellular polymers carry potential environmental risks concerning their reuse. This study employs ultrahigh-performance liquid chromatography-tandem mass spectrometry to investigate the distribution coefficients and occurrence of alginate-like extracellular polymers and sulfamethoxazole. Results demonstrate a negative distribution coefficient, suggesting an inhibitory effect on sulfamethoxazole dissolution. The ethanol-extracted alginate-like extracellular polymers exhibits higher sulfamethoxazole levels (approximately 52%) than those obtained via dialysis extraction. Three-dimensional excitation-emission matrix analysis and adsorption studies indicate the absence of tyrosine-like substances in the alginate-like extracellular polymers, unlike in other extracellular polymeric substances. This absence diminishes hydrophobic interactions, highlighting that electrostatic interactions play a more important role. These insights are crucial for understanding the adsorption behavior of alginate-like extracellular polymers and optimizing their large-scale extraction processes.

Cultivation of phosphate-accumulating biofilm: Study of the effects of acyl-homoserine lactones (AHLs) and cyclic dimeric guanosine monophosphate (c-di-GMP) on the formation of biofilm and the enhancement of phosphate metabolism capacity

This study investigated the mechanisms of microbial growth and metabolism during biofilm cultivation in the biofilm sequencing batch reactor (BSBR) process for phosphate (P) enrichment. The results showed that the sludge discharge was key to biofilm growth, as it terminated the competition for carbon (C) source between the nascent biofilm and the activated sludge. For the tested reactor, after the sludge discharge on 18 d, P metabolism and C source utilization improved significantly, and the biofilm grew rapidly. The P concentration of the recovery liquid reached up to 157.08 mg/L, which was sufficient for further P recovery via mineralization. Meta-omics methods were used to analyze metabolic pathways and functional genes in microbial growth during biofilm cultivation. It appeared that the sludge discharge activated the key genes of P metabolism and inhibited the key genes of C metabolism, which strengthened the polyphosphate-accumulating metabolism (PAM) as a result. The sludge discharge not only changed the types of polyphosphate-accumulating organisms (PAOs) but also promoted the growth of dominant PAOs. Before the sludge discharge, the necessary metabolic abilities that were spread among different microorganisms gradually concentrated into a small number of PAOs, and after the sludge discharge, they further concentrated into Candidatus_Contendobacter (P3) and Candidatus_Accumulibacter (P17). The messenger molecule C-di-GMP, produced mostly by P3 and P17, facilitated P enrichment by regulating cellular P and C metabolism. The glycogen-accumulating organism (GAO) Candidatus_Competibacter secreted N-Acyl homoserine lactones (AHLs), which stimulated the secretion of protein in extracellular polymeric substances (EPS), thus promoting the adhesion of microorganisms to biofilm and improving P metabolism via EPS-based P adsorption. Under the combined action of the dominant GAOs and PAOs, AHLs and C-di-GMP mediated QS to promote biofilm development and P enrichment. The research provides theoretical support for the cultivation of biofilm and its wider application.

Effect of ciprofloxacin on the one-stage partial nitrification and anammox biofilm system: A multivariate analysis focusing on size-fractionated organic components

The impact of ciprofloxacin (CIP) in the partial nitrification and anammox biofilm system was investigated by multivariate analysis, focusing on size-fractionated organic components. The CIP dose of 10 μg/L did not inhibit the total nitrogen (TN) removal efficiency, even though the abundance of antibiotic resistant genes (ARGs) (i.e., qnrD, qnrB, qnrA, qnrS, and arcA) was elevated. However, a gradual higher CIP dosing up to 100 μg/L inhibited the TN removal efficiency, while the abundance of ARGs was still increased. Moreover, both the TN removal efficiency and the abundant ARGs were dwindled at 470 μg/L of CIP. As the CIP dose increased from 0 to 100 μg/L, the abundance of high molecular weight (MW) fractions (14,000 to 87,000 Da; 1000 to 14,000 Da) and humic/fulvic acid-like components in the soluble extracellular polymeric substances (HSS) decreased, with more increases of low MW (84-1000 Da; less than 84 Da) fractions and soluble microbial by-products in soluble extracellular polymeric substances (SMPS). Continuously increasing the CIP dose till 470 μg/L, an inverse trend of the changes of these organic components was noted, along with clear reductions of the microbial diversity and richness, and the abundance of key functional genes responsible for nitrogen removal. The predominance of functional gene amoA (related with ammonia oxidizing bacteria) was more significantly with more distribution of SMPS with relatively low MW and less distribution of HSS with relatively high MW, as well as polymer decomposing microorganisms such as Bryobacteraceae and the unclassified Saprospirales.

Microbial community analysis of membrane bioreactor incorporated with biofilm carriers and activated carbon for nitrification of urine

The integration of powdered activated carbon and biofilm carriers in a membrane bioreactor (MBR) presents a promising approach to address the challenge of long hydraulic retention time (HRT) for nitrification of hydrolysed urine. This study investigated the effect of the incorporation in the MBR on microbial dynamics, focusing on dominant nitrifying bacteria. The results showed that significant shifts in microbial compositions were observed with the feed transition to full-strength urine and across different sludge growth forms. Remarkably, the nitrite-oxidizing bacteria Nitrospira were highly enriched in the suspended sludge. Simultaneously, ammonia-oxidizing bacteria, Nitrosococcaceae thrived in the attached biomass, showing a significant seven-fold increase in relative abundance compared to its suspended counterpart. Consequently, the incorporated MBR displayed 36% higher nitrification rate and 40% HRT reduction compared to the conventional MBR. This study provides valuable insights on the potential development of household or building scale on-site nutrient recovery from urine to fertiliser.

Toxic effect of copper ions on anammox in IFFAS process filled with ZVI-10 modified carriers

The inhibitory effects of heavy metals on anammox bacteria (AnAOB) have attracted attention worldwide. However, most are conducted in activated sludge rather than biofilm systems. The toxic effect and resistance response of anammox biofilm are not predictable from those of free-living AnAOB. Zero valent iron (ZVI) has been demonstrated to enhance anammox performance, but whether ZVI can promote AnAOB resistance to heavy metal stress remains unclear. Herein, the toxic effect of copper ions (Cu(II)) on anammox in integrated floating-film activated sludge (IFFAS) process filled with 10 wt% ZVI modified carriers (R1) was investigated. Results indicated half inhibiting concentration (IC50) of Cu(II) in R1 was 9.13 mg/L, which was much higher than that in R0 filled with conventional carriers made of high density polyethylene (HDPE) (3.94 mg/L). Long-term effect of Cu(II) demonstrated that Cu(II) concentrations less than 1.0 mg/L could not inhibit anammox biofilm significantly, whereas R1 performed better anammox process than R0 under the stress of 0.1-1.0 mg/L Cu(II). The ZVI modified carriers induced more extracellular polymeric substances (EPS) to trap Cu(II) to attenuate the toxicity to AnAOB. Besides, the activities of functional enzymes related to anammox (NIR and HDH), as well as heme-c contents, were always higher in R1 than R0 regardless of the Cu(II) dosage. Candidatus Kuenenia was identified as the predominant AnAOB, which had stronger resistance to Cu(II) stress compared to other genera in the IFFAS process. Metal resistance genes (MRGs) analysis identified AnAOB induced multi-responses to resist Cu(II) stress, such as the up-regulation of copC, cutA, cutC, cutF, cueR and cueO, to synthesize more proteins with functions of copper exocytosis, conjugation and oxidation.

Mathematical modelling and comparative analysis of treatment technologies for upgrading wastewater treatment plants: A case study of biofilm reactors in El-Gouna, Egypt

In recent years, Moving Bed Biofilm Reactors (MBBRs) have been preferred to conventional processes with suspended biomass. The main reason for this preference is that it can achieve better removal efficiencies than conventional systems with smaller footprints. However, unlocking the full potential of MBBRs in large-scale WWTPs remains challenging in real life. In this study, the performance of three different treatment technologies, Extended Aeration Activated Sludge (EAAS), Hybrid Fixed Bed Biofilm Reactor (HFBBR), and Hybrid Moving Bed Biofilm Reactor (HMBBR), was investigated over a year in a WWTP located in El-Gouna, Egypt. The COD removal efficiencies of the three systems were comparable, with the EAAS achieving 93.5%, HFBBR 94%, and HMBRR 95%. Nevertheless, the NH4 removal efficiency of the EAAS was slightly lower (97.5%) than that of the HFBBR and the HMBBR, that achieved a removal efficiency of 98%. BioWin Software was able to mimic the real case of the WWTP of El-Gouna and critically defined all plant limitations and operational data. Different simulations were modeled to test the hydraulic and organic loading capacities of the three systems under different scenarios and operating conditions. The HMBBR system failed to withstand the increase in organic load because of the biomass sloughing effect and subsequently high TSS loads in the settlers. Biomass sloughing overloaded the settlers and lead to biomass loss in the effluent. As the settleability of the HMBBR sludge was significantly lower than for the HFBBR the TSS loss in the effluent happened that much earlier that the moving carrier application had an adverse effect contradicting with the primary purpose of adding media carriers. Model simulations and data analysis findings were used to recommend the most suitable configuration for upgrading an existing system using the attached growth technique with all kinetic parameters and operational conditions. The recommended configuration focuses mainly on the separation of plastic media in a compartment with a very low hydraulic retention time to absorb the incoming shock load.

Fates of extracellular and intracellular antibiotic resistance genes in activated sludge and plastisphere under sulfadiazine pressure

Microplastics, antibiotics, and antibiotic resistance genes (ARGs) represent prominent emerging contaminants that can potentially hinder the efficacy of biological wastewater treatment and pose health risks. Plastisphere as a distinct ecological niche for microorganisms, acts as a repository for ARGs and potential pathogenic bacteria. Nonetheless, the spread pattern of extracellular ARGs (eARGs) and intracellular ARGs (iARGs) in plastisphere under antibiotic exposure was not yet known. This study aimed to investigate disparities in extracellular polymeric substances (EPS) production, extracellular and intracellular microbial community structures, as well as the transmission of eARGs and iARGs between activated sludge and plastisphere in an anaerobic/anoxic/oxic system under sulfadiazine (SDZ) exposure. SDZ was found to enhance EPS production in activated sludge and plastisphere. Interestingly, as SDZ removal efficiency increased, EPS content decreased in activated sludge and plastisphere collected from oxic zone, and continued to increase in plastisphere samples collected from anaerobic and anoxic zones. There were significant differences in microbial community structure between activated sludge and plastisphere, and the DNA fragments of potential pathogenic bacteria were detected in extracellular samples. SDZ exhibited a promoting effect on the propagation of eARGs, which were more abundant in the plastisphere than in activated sludge, thus heightening the risk of ARGs dissemination. Extracellular mobile genetic elements played a pivotal role in driving the spread of eARGs, while the microbial community induced the changes of iARGs. Potential pathogenic bacteria emerged as potential hosts for ARGs and mobile genetic elements within activated sludge and plastisphere, leading to more serious environmental threats.

Effect of Operating Parameters on the Performance of Integrated Fixed-Film Activated Sludge for Wastewater Treatment

Integrated fixed-film activated sludge (IFAS) is a hybrid wastewater treatment process that combines suspended and attached growth. The current review provides an overview of the effect of operating parameters on the performance of IFAS and their implications for wastewater treatment. The operating parameters examined include hydraulic retention time (HRT), solids retention time (SRT), dissolved oxygen (DO) levels, temperature, nutrient loading rates, and aeration. Proper control and optimization of these parameters significantly enhance the treatment efficiency and pollutant removal. Longer HRT and appropriate SRT contribute to improved organic matter and nutrient removal. DO levels promote the growth of aerobic microorganisms, leading to enhanced organic matter degradation. Temperature influences microbial activity and enzymatic reactions, impacting treatment efficiency. Nutrient loading rates must be carefully managed to avoid system overload or inhibition. Effective aeration ensures uniform distribution of wastewater and biofilm carriers, optimizing contact between microorganisms and pollutants. IFAS has been used in water reuse applications, providing a sustainable and reliable water source for non-potable uses. Overall, IFAS has proven to be an effective and efficient treatment process that can provide high-quality effluent suitable for discharge or reuse. Understanding the effects of these operating parameters helps to optimize the design and operation for efficient wastewater treatment. Further research is needed to explore the interactions between different parameters, evaluate their impact under varying wastewater characteristics, and develop advanced control strategies for improved performance and sustainability.

Enhanced anaerobic degradation of azo dyes by biofilms supported by novel functionalized carriers

Azo dyes are significant organic pollutants known for their adverse effects on humans and aquatic life. In this study, anthraquinone-2-sulfonate (AQS) immobilized on biochar (BC) was employed as a novel carrier in up-flow anaerobic fixed-bed reactors to induce specific biofilm formation and promote the biotransformation efficiency of azo dyes. Novel carrier-packed reactor 1 (R1) and BC-packed reactor 2 (R2) were used to treat red reactive 2 (RR2) under continuous operation for 175 days. The decolorization rates of R1 and R2 were 96-83% and 91-73%, respectively. The physicochemical characteristics and extracellular polymeric substances (EPS) of the biofilm revealed a more stable structure in R1. Furthermore, the microbial community in R1 interacted more closely with each other and contained more keystone genera. Overall, this study provides a feasible method for improving the biotransformation of azo dyes, thus providing support for practical applications in wastewater treatment projects.

Deciphering community assembly and succession in sequencing batch moving bed biofilm reactor: Differentiation between attached and suspended communities

Elucidating community assembly and succession is crucial to understanding the ecosystem functioning. Herein, the ecological processes underpinning community assembly and succession were studied to uncover the respective ecological functions of attached biofilms and suspended biomass in a sequencing batch moving bed biofilm reactor. Compared with suspended biomass, attached biofilms presented higher relative abundances of Nitrospira (2.94 %) and Nitrosomonas (1.25 %), and contributed to 66.89 ± 11.37 % and 68.11 ± 12.72 % of nitrification and denitrification activities, respectively. The microbial source tracking result demonstrated that early formation of suspended biomass was dominated by the seeding effect of detached biofilms in the start-up period (days 0-30), while self-growth of previous suspended biomass was eventually outcompeted the seeding effect when the reactor stabilized (days 31-120). Null model and ecological network analysis further suggested distinctive ecological processes underpinning the differentiation between attached and suspended communities in the same reactor. Specifically, in the start-up period, positive interactions facilitated early formation of attached (73.84 %) and suspended communities (59.41 %), while homogenous selection (88.89 %) and homogenizing dispersal (65.71 %) governed assembly of attached and suspended communities, respectively. When the reactor stabilized, attached and suspended communities showed low composition turnover as reflected by dominant homogenizing dispersal, while they presented distinctive trends of interspecies interactions. This study sheds light on discrepant ecological processes governing community differentiation of attached biofilms and suspended biomass, which would provide ecological insights into the regulation of hybrid ecosystems.

Celebrating 50 years of microbial granulation technologies: From canonical wastewater management to bio-product recovery

Microbial granulation technologies (MGT) in wastewater management are widely practised for more than fifty years. MGT can be considered a fine example of human innovativeness-driven nature wherein the manmade forces applied during operational controls in the biological process of wastewater treatment drive the microbial communities to modify their biofilms into granules. Mankind, over the past half a century, has been refining the knowledge of triggering biofilm into granules with some definite success. This review captures the journey of MGT from inception to maturation providing meaningful insights into the process development of MGT-based wastewater management. The full-scale application of MGT-based wastewater management is discussed with an understanding of functional microbial interactions within the granule. The molecular mechanism of granulation through the secretion of extracellular polymeric substances (EPS) and signal molecules is also highlighted in detail. The recent research interest in the recovery of useful bioproducts from the granular EPS is also emphasized.

De novo granulation of sewage-borne microorganisms: A proof of concept on cultivating aerobic granular sludge without activated sludge and effective enhanced biological phosphorus removal

Long start-up periods for granulating activated sludge and concerns on granular stability are the bottlenecks reported during implementation of novel aerobic granular sludge (AGS) technology in municipal wastewater treatment plants. Here, de novo granulation of sewage-borne microorganisms without using activated sludge (AS) inoculum was investigated in bench-scale sequencing batch reactors (SBR). Data showed that formation of AGS from sewage-borne microorganisms was rapid and first granules appeared within one week. Granulation was indicated by appearance of biomass particles (size >0.12 mm), high biomass levels (∼8 g/L) and superior settling properties (SVI_30 min: 30 mL/g). Granulation process involved distinct stages like formation of aggregates, retention of aggregates, and growth of millimetre sized granules. Simultaneous COD, nitrogen and phosphorous removal was established within 10 days of start-up in the SBR without using AS inoculum. However, phosphorus removal became stable after 50 days of start-up. Total nitrogen (TN) and total phosphorus (TP) removals of 92% and 70%, respectively, were achieved from real domestic wastewater. Furthermore, addition of granular activated carbon (GAC) had improved both granulation and biological nutrient removals. Interestingly, phosphorus removal became quite stable within 10 days of start-up in the SBR operated with GAC particles. TN and TP removals were found to be higher at >98% and >94%, respectively, in GAC-augmented SBR. Removal of ammonia and phosphorus were mediated by nitritation-denitritation and enhanced biological phosphorus removal (EBPR) pathways, respectively. The bacterial diversity of AGS was lower than that of sewage. Quantitative PCR indicated enrichment of ammonia oxidizing bacteria, denitrifying bacteria and polyphosphate accumulating organisms during granulation. De novo granulation of sewage-borne microorganisms is a promising approach for rapidly cultivating AGS and establishing biological nutrient removal in sewage treatment plants.

Morphological image analysis of biofilm evolution with quantitative analysis in a moving bed biofilm reactor

The quantitative analysis of biomass is essential for the research and application of moving bed biofilm reactors (MBBRs). However, the difficulty in measuring the attached growing biomass hinders the quantitative analysis of biofilm processes. In this study, a pilot-scale MBBR system was established to investigate biofilm evolution. The quantity of active heterotrophic and autotrophic biomass was measured throughout the entire culturing process. The total active biomass reached 250 mg COD/m² when the biofilm attachment and detachment were balanced, and the corresponding autotrophic biomass contributes to as high as 17 % of the total biomass. Furthermore, quantitative image analysis was performed to obtain the thickness and morphological data of the biofilm evolution. Multivariate regression models were constructed based on the morphological data, which provided satisfactory prediction accuracy for the biofilm thickness and maturation. The most suitable carrier spots for biomass quantification and biofilm maturation were suggested. This work provided the life-cycle information of biofilm quantity and morphology of the MBBR, which contributes to the quantitative understanding of biofilm evolution at MBBRs.

A novel 3D volumetric method for directly quantifying porosity and pore space morphology in flocculated suspended sediments

Flocculated suspended sediments (flocs) are found in a variety of environments globally, and their transport and behavior bear substantial importance to several industries including fisheries, aquaculture, and shipping. Additionally, the modelling of their behavior is important for estuarine and coastal flood prediction and defence, and the process of flocculation occurs in other unrelated industries such as paper and chemical production. Floc porosity is conventionally assessed using inferential indirect or proxy data approaches. These methods underestimate floc porosity % by c. 30% and cannot measure the micro-scale complexity of these pore spaces and networks, rendering inputs to models sub-optimal. This study introduces a novel 3D porosity and pore space quantification protocol, that produces directly quantified porosity % and pore space data.•3D floc data from micro-CT scanning is segmented volumetrically•This segmented volume is quantified to extract porosity and several pore space parameters from the floc structure.

Development of microbial communities in biofilm and activated sludge in a hybrid reactor

Microorganisms play a key role in biological wastewater treatment. The form in which biomass develops determines the efficiency and mechanisms of organic compound conversion, due to different conditions in various microbial structures. However, the results of studies comparing the microbial communities in biofilm and activated sludge have often conflicted. Therefore, this study compared the composition and development of the bacterial communities in biofilm and activated sludge in a hybrid reactor, employing 16S rRNA sequencing. Statistical analysis of the sequencing data included the identification of taxa characteristic to the biofilm and activated sludge, alpha and beta diversity analysis, and network analysis. These analyses indicated that the biofilm bacterial community was richer and more diverse than the activated sludge community. The mean numbers of OTU were 1614 in the biofilm and 993 in the activated sludge, and the mean values of the Chao1 (1735 vs. 1105) and Shannon (5.3 vs. 4.3) biodiversity indices were significantly higher for the biofilm. The biofilm was a better environment for development of nitrifiers (e.g., Nitrosomonas, Nitrospira) and phosphorus accumulating organisms (Candidatus Accumulibacter). Bacteria in the biofilm co-occurrence network had more connections (based on Spearman's rank correlation coefficient) with each other, indicating that they interact more than those in the activated sludge.

Extracellular DNA plays a key role in the structural stability of sulfide-based denitrifying biofilms

Sulfide-based biofilm processes are increasingly used for wastewater denitrification, yet little is known about the extracellular polymeric substance (EPS) composition of sulfide-oxidizing biofilms. This can have an important impact on biofilm mechanical strength and stability. In this research, the properties and roles of EPS components in biofilm stability were investigated. Weak biofilm stability characterized by high roughness and numerous "needle" structures was visualized by optical coherence tomography (OCT) and microscopy. A high abundance of extracellular DNA (eDNA) and a low protein to polysaccharide ratio were found in the biofilm. The roles of eDNA, protein and polysaccharide in biofilm cohesion and adhesion were identified through enzyme treatment and atomic force microscopy (AFM). The enzymatic hydrolysis of eDNA increased the elastic modulus of biofilms by 57 times and reduced the adhesion energy by 96%. The hydrolysis of proteins led to an increase of elastic modulus by 27 times and a loss of adhesion energy by 95.5%. The enzymatic hydrolysis of polysaccharides caused minimal changes in elastic modulus and adhesion energy. These results suggest that eDNA was the key EPS component for biofilm cohesion and adhesion, possibly because it provided special binding sites and can form strong cross-linking with magnesium or other multivalent cations. This study provided new insights into the role of eDNA in biofilm stability and shed light on the development of sulfide-based denitrifying biofilms.

Enhancing extraction of alginate like extracellular polymers (ALE) from flocculent sludge by surfactants

Alginate like extracellular polymers (ALE) recovered from flocculent sludge has been identified as a kind of highly valuable biomaterials. However, the extraction protocols limit the production of biopolymers as ALE extracted from flocculent sludge is at a lower level, around 90-190 mg/g VSS. Under this circumstance, the eco-friendly and effective optimizations for the ALE extraction protocols are expected, and thus surfactants have gained an attention to enhancing the ALE extraction. With this study, different surfactants with different structures and chemical characteristics, such as sodium dodecyl sulfate (SDS), cetyltrimethylammonium bromide (CTAB) and octyl phenyl polyoxyethylene ether (Triton X-100), were experimented to improve the ALE extraction, and in turn the optimal conditions and the associated mechanisms were evaluated and figured out. The experimental results indicated that surfactants could enhance the ALE extraction but also improve the alginate purification of ALE. With the optimal dosage of surfactants, the ALE extraction increased from 124.1 mg/g VSS to about 222.8-281.9 mg/g VSS, and the alginate purify was at around 54%-70%, in which the efficiency of the ALE extraction was improved by 79.5%-127.2%. Among others, Triton X-100 had the best performance on improving the ALE extraction, followed by CTAB and SDS. The mechanisms of surfactants on enhancing the ALE extraction and improving the alginate purify can be attributed to: i) surfactants micelles, which can solubilize flocs and extracellular biopolymers; ii) similar structures of surfactants and ALE, which follows the rule of "like dissolves like"; iii) functional groups adsorption, which facilitates the ALE release from matrixes. In a word, the optimized extraction protocol by using surfactants can be effectively applied to extract ALE from flocculent sludge.

Enhancing anaerobic methane production in integrated floating-film activated sludge system filled with novel MWCNTs-modified carriers

Conductive materials can enhance anaerobic methane production by accelerating interspecies electron transfer between electroactive bacteria and methanogens. However, the daily loss or less specific surface area of small/big size of conductive materials always limits their application in anaerobic digestion. In this study, the conductive multi-walled carbon nanotubes (MWCNTs) (15 wt% and 20 wt%) were mixed with high-density polyethylene (HDPE) and novel conductive suspended carriers were prepared. Results showed the conductivity of the novel conductive suspended carriers increased by 1-2 orders of magnitude comparing with HDPE carriers, as well as the attached biomass improved from 3.93 g/m² (HDPE carriers) to 5.82 g/m² (15 wt% MWCNTs-modified carriers) and 6.67 g/m² (20 wt% MWCNTs-modified carriers). Integrated floating-film activated sludge (IFFAS) filled with MWCNT-modified carriers showed significant advantages in chemical oxygen demand (COD) removal (removal efficiency increased by 3.6-37.2%) and methanogenic performance (cumulative methane increased by 12.28-62.91%) compared with the control reactor filled with conventional HDPE carriers when treating sodium propionate wastewater at the organic loading rates (OLR) of 11.3-26.3 kg COD/(m³∙d). SEM images and high-throughput sequencing results proved potential direct interspecies electron transfer (DIET) had been established successfully on the MWCNTs-modified carriers. The syntrophic electroactive bacteria (Geobacter, Thauera) and Methanotrix were enriched by 2.28-4.58% and 9.41-16.80% respectively owning to the addition of novel conductive carriers. This study proved IFFAS process filled with novel MWCNTs-modified suspended carriers showed great potential in establishing DIET to enhance anaerobic digestion in practical application.

Unveiling organic loading shock-resistant mechanism in a pilot-scale moving bed biofilm reactor-assisted dual-anaerobic-anoxic/oxic system for effective municipal wastewater treatment

Microbial biomass and activity are frequently subjected to organic loading shock (OLS) from decentralized municipal wastewater. A hybrid moving bed biofilm reactor-assisted dual-anaerobic-anoxic/oxic system (D-A²MBBR) was established by integrating dual-anaerobic-anoxic/oxic with moving bed biofilm reactor to resist OLS for stable nutrients removal. The D-A²MBBR achieved 91.57% of chemical oxygen demand, 93.33% of ammonia-nitrogen, 80.20% of total nitrogen and 92.68% of total phosphorus removal, respectively, under the fluctuation of organic loading rate from 417.9 to 812.0 g COD m^-3 d^-1. The 16S rRNA gene sequencing revealed that Gemmobacter (7.28%) was identified as dominating anoxic denitrifying genus in oxic chamber, confirming the coexistence of aerobic and anaerobic/anoxic micro-environments. This circumstance boosted simultaneous nitrification-denitrification and phosphorus removal and the microbial community evolution inside the multilayer biocarrier-attached biofilms. In general, the D-A²MBBR was able to provide unique, cooperative and robust bacterial consortia to form a buffer against OLS, and ensuring effluent stability.

Fate of sloughed biomass in integrated fixed-film systems

Fate of biofilm sloughing was assessed in a laboratory-scale (LS) integrated fixed-film sequencing batch reactor (IF-SBR) treating synthetic wastewater and in a full-scale (FS) integrated fixed-film activated sludge (IFAS) system treating municipal wastewater. It was observed that the properties of biofilms and flocs, including sludge volume index (SVI), mixed liquor suspended solids (MLSS), effluent suspended solids (ESS), relative hydrophobicity, and composition of extracellular polymeric substance (EPS) were associated with biofilm sloughing and formation of large granular flocs in the LS IF-SBR. In the FS IFAS system, the changes were studied at the molecular level. For example, the extracted EPS content results (the protein to polysaccharide ratio decreased in the flocs and increased in the biofilms, with biofilm sloughing) were complemented with the confocal laser scanning microscopy (CLSM) coupled with molecular specific staining. CLSM analyses revealed that micro-colonies rich in polysaccharides readily sloughed from the carriers. Live-dead staining revealed areas of the biofilm where the viability of biomass was a contributing factor associated with areas of the biofilm susceptible to sloughing. 16S rRNA gene sequencing (Illumina) of FS IFAS samples revealed greater diversity (α-diversity) in biofilms compared to flocs. Biofilm sloughing resulted in a decrease in diversity in biofilms and a corresponding increase in the flocs during sloughing. Microbial population dynamics revealed that bacteria known for denitrification (for example, Comamonadaceae) detached from the biofilms during sloughing, readily associated with the suspended biomass, and were retained in the bioreactors.

Enhancing anoxic denitrification of low C/N ratio wastewater with novel ZVI composite carriers

External organic carbon sources are needed to provide electron donors for the denitrification of wastewater with a low COD/NO₃^--N (C/N) ratio, increasing the treatment cost. The economic strategy is to enhance the bioactivity and/or biodiversity of denitrifiers to efficiently utilize organic substances in wastewater. In this study, novel zero-valent iron (ZVI) composite carriers were prepared and implemented in a suspended carrier biofilm reactor to enhance the bioactivity and/or biodiversity of denitrifiers. At the influent C/N ratio of 4 (COD was 179.5 ± 5.0 mg/L and TN was 44.2 ± 0.8 mg/L), COD and TN removal efficiencies were 85.1% and 66.4%, respectively, in the reactors filled with 3 wt% ZVI composite carriers. In contrast, COD and TN removal efficiencies were 70.4% and 55.3%, respectively, in the reactor filled with conventional high-density polyethylene (HDPE) biofilm carriers. The biofilm formation on the 3 wt% ZVI composite carriers was optimized due to its higher roughness (surface square roughness increased from 76.0 nm to 93.8 nm) and favorable hydrophilicity (water contact angle dropped to 72.5° ± 1.4° from 94.3° ± 3.2°) compared with the HDPE biofilm carriers. In addition, heterotrophic denitrifiers, Thauera and Dechloromonas, were enriched, whereas autotrophic denitrifiers, Raoultella and Thiobacillus, exhibited high relative abundance in the biofilm of ZVI composite carriers. The coexistence of heterotrophic denitrifiers and autotrophic denitrifiers on the surface of ZVI composite carriers provided mixotrophic metabolism of denitrification (including heterotrophic and iron-based autotrophic), thereby ensuring effective denitrification for wastewater with a low C/N ratio without external organic carbon source addition.

Bacterial biofilm and extracellular polymeric substances in the moving bed biofilm reactor for wastewater treatment: A review

Among the several biofilm-based bioreactors, moving bed biofilm reactors (MBBR) have been extensively used for wastewater treatment due to low operational costs, technical feasibility, and stability. Biofilm forming strains, e.g., Stenotrophomonas maltophila DQ01, achieved 94.21% simultaneous nitrification and denitrification (SND) and 94.43% removal of total nitrogen (TN) at a cycle time of 7 h, and a biofilm consortium consisting of Chryseobacteriumsp. andRhodobactersp. achieved 86.8% removal of total organic carbon (TOC) at hydraulic retention time (HRT) of 24 h using lab-scale MBBR. Modifications in the surface properties of the biocarrier materials achieved 99.5 ± 1.1% chemical oxygen demand (COD) and 93.6 ± 2.3% NH₄⁺-N removal, significantly higher than the conventional commercial carrier. This review article summarizes the application of MBBR technology for wastewater treatment. The importance of bacterial biofilm and extracellular polymeric substances (EPS), anammox-n-DAMO coupled processes, and carrier surface modifications in MBBR technology have also been discussed.

Optimization nutrient removal at different volume ratio of anoxic-to-aerobic zone in integrated fixed-film activated sludge (IFAS) system

This study evaluated the influence of different volume ratios of the anoxic-to-aerobic zone (V_ano/V_aer) on the enhancement of nitrogen and phosphorus removal in an integrated fixed-film activated sludge (IFAS) system. As the V_ano/V_aer increased from 1:2 to 2:1, the removal of organic carbon, nitrogen and phosphorus nutrients of the IFAS system was improved. At V_ano/V_aer = 1:1, the removal effect of nitrogen and phosphorus nutrients was optimal, and the average removal rates of COD, NH₄⁺-N, TN, and TP of the system reached 90 ± 3.2%, 98.2 ± 1.4%, 88.9 ± 2.2%, and 89.1 ± 2.7%, respectively. As the volume of the anoxic zone continued to increase, the denitrifying phosphate-accumulating capacity of the system was enhanced, and the highest ratio of specific anoxic and aerobic phosphorus uptake rate could reach 65.3%. Analysis of the molecular evaluation showed that, the proportion of nitrifying bacteria in the biofilm gradually increased as V_ano increased. Moreover, denitrifying phosphate-accumulating organisms (DNPAOs), ammonia-oxidizing archaea (AOA), and anaerobic ammonium oxidizing (Anammox) bacteria were all enriched all showed enrichment in the biofilm of fiber carriers, which further strengthened the system's synergistic removal of nitrogen and phosphorus.

Recovery of extracellular biopolymers from conventional activated sludge: Potential, characteristics and limitation

Extracellular polymeric substances (EPS) are biopolymers that can be recovered from excess sludge, which could contribute to a more sustainable wastewater treatment plant (WWTP) operation. An example is alginate like extracellular polymers (ALE) contained in the biopolymers could be a potential resource with a highly-added value. EPS extraction for ALE from aerobic granules sludge (AGS) has already been well studied and applied in the Netherlands. On the other hand, there is little attention to the recovery of biopolymers from conventional activated sludge (CAS). In this study, flocculent sludge from eight CAS-WWTPs in China was collected and their EPS/biopolymers were extracted to investigate their recovery potential, chemical & physical properties and limiting factors. The results revealed that the biopolymers extracted and purified from CAS ranged from 90 to 190 mg/g VSS. The compositional characteristics of the biopolymers were observed by FT-IR, 3D-EEM and UV-Visible spectra, demonstrating some differences in the composition and property of the biopolymers from the different WWTPs. The biopolymers had a similarity of about 60% to a commercial alginate with respect to chemical functional groups and the alginate equivalent was >400 mg/g biopolymers. Moreover, the biopolymers consisted of poly (guluronic acid) blocks (20%-30%) and poly (guluronic acid-mannuronic acid) blocks (8%-28%), and the ionic hydrogel formation tests indicated that condensed beads were immediately formed once the drops of the biopolymers came in contact with CaCl₂ solution. These results demonstrated that the biopolymers extracted had a relatively high gel-forming capacity and might also have a potential application as commercial biopolymers. Furthermore, the factors influencing the biopolymers' formation such as influent substrate, nutrient content and microbial community and the related mechanisms were investigated. Among them, increasing soluble organics (SCOD) content and low nutrient content (C/N/P) in the influent could promote the biopolymers' formation. Also, different bacteria in BNR processes might have positive or negative effects on the biopolymers' formation. In conclusion, the diversity and abundance of bacteria were identified to be a crucial and decisive factor controlling biopolymers' extraction and composition.

Recent advancements in the biological treatment of high strength ammonia wastewater

The estimated global population growth of 81 million people per year, combined with increased rates of urbanization and associated industrial processes, result in volumes of high strength ammonia wastewater that cannot be treated in a cost-effective or sustainable manner using the floc-based conventional activated sludge approach of nitrification and denitrification. Biofilm and aerobic granular sludge technologies have shown promise to significantly improve the performance of biological nitrogen removal systems treating high strength wastewater. This is partly due to enhanced biomass retention and their ability to sustain diverse microbial populations with juxtaposing growth requirements. Recent research has also demonstrated the value of hybrid systems with heterogeneous bioaggregates to mitigate biofilm and granule instability during long-term operation. In the context of high strength ammonia wastewater treatment, conventional nitrification-denitrification is hampered by high energy costs and greenhouse gas emissions. Anammox-based processes such as partial nitritation-anammox and partial denitrification-anammox represent more cost-effective and sustainable methods of removing reactive nitrogen from wastewater. There is also growing interest in the use of photosynthetic bacteria for ammonia recovery from high strength waste streams, such that nitrogen can be captured and concentrated in its reactive form and recycled into high value products. The purpose of this review is to explore recent advancements and emerging approaches related to high strength ammonia wastewater treatment.

Performance and mechanism of a novel woodchip embedded biofilm electrochemical reactor (WBER) for nitrate-contaminated wastewater treatment

In this study, a woodchip biofilm electrode reactor (WBER) with woodchips embedded anode and cathode was developed, and its denitrification mechanism was analyzed by investigating the denitrification performance, organic matter change, redox environment and microbial community. The results show that the WBER with a carbon rod as anode (C-WBER) had a higher denitrification efficiency (2.58 mg NO- 3-N/(L·h)) and lower energy consumption (0.012 kWh/g NO- 3-N) at 350 mA/m². By reducing the hydroxyl radical and dissolved oxygen concentrations, anode embedding technology effectively decreased the inhibition on microorganisms. Lignin decomposition, nitrification and aerobic denitrification were carried out in anode. Additionally, hydrogen autotrophic denitrification and heterotrophic denitrification were occurred in cathode. The WBER effectively removed nitrate and reduced the cost, providing a theoretical basis and direction for further develop BERs.

A novel integrated bio-reactor of moving bed and constructed wetland (MBCW) for domestic wastewater treatment and its microbial community diversity

An MBBR and CW combo bio-reactor (MBCW) was designed as a novel hybrid process for simultaneous organic, nitrogen and phosphate removal through the long-term operation. The effect of the internal recycling rate (IRR), hydraulic retention time (HRT) and chemical oxygen demand/total nitrogen (C/N) ratio were all discussed, and the recommended values were 5:1, 12 h and >6, respectively. A higher C/N ratio was a key factor for achieving a higher TN removal. The mixed biocarrier system was realized by inoculating porous polymer carriers (PPC) and cylindrical polyethylene carriers (CPC) and achieving a higher organic biodegradation and nitrification rate compared to a single carrier system. Microorganism activities and plants' uptake or utilization both contributed to the nutrient removal in a constructed wetland. High-throughput sequencing results revealed an abundant microbial diversity and a distinct microbial distribution in the whole system where Flavobacterium (14.2%), Acinetobacter (12.87%) and Rhodobacter (10.83%) dominated on PPC, Terrimonas (8.88%), Reyranella (6.61%) and Rubinisphaera (5.63%) dominated on CPC, Comamonas (4.18%), Gemmobacter (4.02%) and Hydrogenophaga (3.97%) dominated on CWs, as well as Citrobacter (53.13%) on suspended floc.

Effect of nanobubble application on performance and structural characteristics of microbial aggregates

Herein an investigation on the performance and structural properties with aspects of stability, composition, functional group, and three-dimensional distribution were approached to evaluate the influence of nanobubble aeration to the two most common microbial aggregates, activated sludge and biofilm. This study found that applying nanobubble effectively provided extra oxygen for microbial aggregates and achieved a 10.58% improvement in total nitrogen removal. The structure of microbial aggregates was enhanced, where extracellular protein and polysaccharides respectively increased as maximum as 3.40 and 1.70 times in biofilm and activated sludge, accompanied by the development of activated sludge floc size and the thickness of biofilm. Further investigation on extracellular polymeric substance and surface of microbial aggregates showed the composition of functional substances of microbial aggregates were shifted by the application of nanobubble, especially the oxygen-sensitive ones. Confocal laser scanning microscopy imaging visualized that the nanobubble changed the morphology of biofilm to a more evenly one. However, an adaptive process was more needed for activated sludge rather than biofilm, it suggested application of NB optimized the distribution of functional microorganisms in-depth and the metabolism pathway of them by accelerating the structure development of microbial aggregates, especially for biofilm.

Autotrophic Fixed-Film Systems Treating High Strength Ammonia Wastewater

The aim of the study was enrichment of nitrifying bacteria and to investigate the potential of autotrophic fixed-film and hybrid bioreactors to treat high strength ammonia wastewater (up to 1,000 mg N/L). Two types of fixed-film systems [moving bed biofilm reactor (MBBR) and BioCord^TM] in two different configurations [sequencing batch reactor (SBR) and a continuous stirred tank reactor (CSTR)] were operated for 306 days. The laboratory-scale bioreactors were seeded with activated sludge from a municipal wastewater treatment plant and fed synthetic wastewater with no organics. Strategies for acclimation included biomass reseeding (during bioreactor start-up), and gradual increase in the influent ammonia concentration [from 130 to 1,000 mg N/L (10% every 5 days)]. Stable ammonia removal was observed up to 750 mg N/L from 45 to 145 days in the MBBR SBR (94-100%) and CSTR (72-100%), and BioCord^TM SBR (96-100%) and CSTR (92-100%). Ammonia removal declined to 87% ± 6, in all bioreactors treating 1,000 mg N/L (on day 185). Following long-term operation at 1,000 mg N/L (on day 306), ammonia removal was 93-94% in both the MBBR SBR and BioCord^TM CSTR; whereas, ammonia removal was relatively lower in MBBR CSTR (20-35%) and BioCord^TM SBR (45-54%). Acclimation to increasing concentrations of ammonia led to the enrichment of nitrifying (Nitrosomonas, Nitrospira, and Nitrobacter) and denitrifying (Comamonas, OLB8, and Rhodanobacter) bacteria [16S rRNA gene sequencing (Illumina)] in all bioreactors. In the hybrid bioreactor, the nitrifying and denitrifying bacteria were relatively more abundant in flocs and biofilms, respectively. The presence of dead cells (in biofilms) suggests that in the absence of an organic substrate, endogenous decay is a likely contributor of nutrients for denitrifying bacteria. The nitrite accumulation and abundance of denitrifying bacteria indicate partial denitrification in fixed-film bioreactors operated under limited carbon conditions. Further studies are required to assess the contribution of organic material produced in autotrophic biofilms (by endogenous decay and soluble microbial products) to the overall treatment process. Furthermore, the possibility of sustaining autotrophic nitrogen in high strength waste-streams in the presence of organic substrates warrants further investigation.

Recent progress in integrated fixed-film activated sludge process for wastewater treatment: A review

Integrated fixed-film activated sludge (IFAS) process is considered as one of the leading-edge processes that provides a sustainable solution for wastewater treatment. IFAS was introduced as an advancement of the moving bed biofilm reactor by integrating the attached and the suspended growth systems. IFAS offers advantages over the conventional activated sludge process such as reduced footprint, enhanced nutrient removal, complete nitrification, longer solids retention time and better removal of anthropogenic composites. IFAS has been recognized as an attractive option as stated from the results of many pilot and full scales studies. Generally, IFAS achieves >90% removals for combined chemical oxygen demand and ammonia, improves sludge settling properties and enhances operational stability. Recently developed IFAS reactors incorporate frameworks for either methane production, energy generation through algae, or microbial fuel cells. This review details the recent development in IFAS with the focus on the pilot and full-scale applications. The microbial community analyses of IFAS biofilm and floc are underlined along with the special emphasis on organics and nitrogen removals, as well as the future research perspectives.

Enhancing anaerobic digestion in anaerobic integrated floating fixed-film activated sludge (An-IFFAS) system using novel electron mediator suspended biofilm carriers

Suspended biofilm carriers mediating direct interspecies electron transfer (DIET)-based syntrophic metabolism is a promising strategy to enhance anaerobic digestion and methane production by associating the advantages of conductive suspended biofilm carriers and anaerobic integrated floating fixed-film and activated sludge (An-IFFAS) process. However, the current knowledge of DIET using conductive suspended biofilm carrier is still limited. In this study, novel electron mediator suspended biofilm carriers had been prepared by introducing a series of graphite powders (3 wt%, 5 wt% and 7 wt%) into high-density polyethylene (HDPE), and applied in An-IFFAS reactors. Results showed that An-IFFAS reactors filled with graphite-modified carriers could enhance the degradation of organic matters and the production of methane significantly in comparison with the control reactor filled with conventional HDPE carriers at organic loading rates (OLRs) of 5.9-23.7 kg COD/m³/d. Microbial analysis proved that 7 wt% graphite-modified carrier improved approximately 4.2% abundance of Geobacter and 7.3% abundance of electrotrophic methanogens (Methanothrix) that exchange electron via DIET comparing with that of HDPE carriers, respectively. These findings demonstrated that electron mediator suspended biofilm carrier was able to potentially proceed DIET and enhance the efficiency of anaerobic digestion and recover CH₄-related energy.

Biofilm characteristics, microbial community structure and function of an up-flow anaerobic filter-biological aerated filter (UAF-BAF) driven by COD/N ratio

The biofilm characteristics, microbial community structure and function in a lab-scale up-flow anaerobic filter-biological aerated filter (UAF-BAF) driven by COD/N ratio were investigated. Results showed that the TN removal rate of system reduced from 68.7% to 50.6% with COD/N ratio ranging from 10 to 3. Biofilm characteristics analysis indicated that the biomass, biofilm thickness, polysaccharide and protein contents in extracellular polymeric substance and dehydrogenase activity from biofilm in the UAF-BAF declined with the decrease of COD/N ratio. The biofilm structure visualized by confocal laser scanning microscopy displayed that the total cells and EPS content decreased as the COD/N ratio downshifted. 16S rRNA sequencing illustrated that Zoogloea and Pleomorphomonas were the major contributors to TN removal in the UAF, with dramatically decreasing abundance. Functional prediction indicated that the genes involved in nitrogen metabolism and nitrate reductase (EC 1.7.99.4) also decreased, which was responsible for the decrease of TN removal. This study provided insights into understanding of the biofilm structure and underlying ecological function in the UAF-BAF, which would help to regulate wastewater biofilm and improve process performance.

Ecological insights into the underlying evolutionary patterns of biofilm formation from biological wastewater treatment systems: Red or Black Queen Hypothesis?

Interspecies interactions and phylogenetic distances were studied to reveal the underlying evolutionary adaptations of biofilms sourced from wastewater treatment processes. Based on 380 pairwise cocultures of 40 strains from two microbial aggregates (surface-attached and mobile aggregates [flocs]) at two substrate concentrations (LB broth and 0.1× LB broth), interspecies interactions were explored using biofilm classification schemes. There was a strong source-dependence of biofilm development formed by the monocultures, that is, a higher biofilm formation potential for strains from attached aggregates than for those from sludge flocs at both substrate concentrations. Interestingly, the results showed that total biofilm reduction was dominant in the dual-species biofilm sourced from flocs in both LB broth (67.37%) and 0.1× LB broth (64.21%), indicating high interspecific competition in mobile aggregates and the independence of substrate concentrations. However, biofilm reduction was higher (33.68%) than induction (19.37%) for the biofilms formed by surface-attached aggregates in LB broth, while the opposite trend was apparent in 0.1× LB broth, suggesting the occurrence of indeterministic processes for biofilm formation and important roles of substrate concentrations. In addition, the more closely related phylogenetic relationships of cocultures from mobile aggregates were consistent with higher competition compared with those from surface-attached aggregates. Overall, the underlying evolutionary patterns of biofilms formed from mobile aggregates consistently followed the essence of the "Red Queen Hypothesis," while biofilms developed from surface-attached aggregates were not deterministic. This study advanced our understanding of biofilm-related treatment processes using the principles of microbial ecology.

Integrated effects of temperature and COD/N on an up-flow anaerobic filter-biological aerated filter: Performance, biofilm characteristics and microbial community

The integrated effects of temperature and COD/N ratio on performance, biofilm characteristics and microbial community in up-flow anaerobic filter-biological aerated filters (UAF-BAFs) were investigated. Results indicated that the UAF-BAF system could achieve excellent COD, NH₄⁺-N and TN removal, in which effluent quality well met the Class 1A standard. Biofilm physicochemical characteristics showed that the biomass, biofilm thickness and extracellular polymeric substance (EPS) content in the UAF-BAFs reduced with the decrease in COD/N ratio, but were enhanced under low temperature. The biofilm structure characterized by CLSM in the UAF-BAFs significantly shifted, which was closely correlated with operational conditions. Sequencing analysis revealed that Proteobacteria, Epsilonbacteraeota, Bacteroidetes and Firmicutes were dominant in the UAFs and the abundance of ammonium oxidizing bacteria (AOB) was responsible for nitrification performance in the BAFs. Functions analysis indicated that amino acid metabolism, carbohydrate metabolism, energy metabolism and lipid metabolism were clearly regulated by parameters changes.

Moving bed biofilm reactor technology in municipal wastewater treatment: A review

The review encompasses the development of municipal wastewater treatment process using MBBR from early stages, established application, and recent advancements. An overview of main drivers leading to the MBBR technology development over its early stage is discussed. Biocarriers types and features together with biofilm development and role of extracellular polymeric substances (EPS) are presented, ultimately, addressing the challenge in decreasing startup time required for full operation. Furthermore, the review investigates the state of the art of MBBR technology for nutrient removal (i.e., COD and BOD, nitrogen and phosphorus) through process functionality and configuration of established (e.g., IFAS) and under development (e.g. PN/A) applications. Reactor operational characteristics such as filling fractions, mixing properties, dissolved oxygen requirements, and loading rates are presented and related to full scale examples. Current literature discussing the most recent studies on MBBR capability in reduction and removal of chemicals of emerging concern (CEC) released is presented. Ultimately, high rate carbon and nitrogen removal through A/B stage process are examined in its main operational parameters and its application towards energy neutrality suggesting novel MBBR application to further reduce energy requirements and plant footprint.

Comparative investigation on carbon-based moving bed biofilm reactor (MBBR) for synchronous removal of phenols and ammonia in treating coal pyrolysis wastewater at pilot-scale

By regulating the extraction solvent and alkali in pretreatment, two carbon-based MBBRs were compared in pilot-scale to synchronously remove phenols and ammonia of coal pyrolysis wastewater (CPW) under fluctuant phenols-ammonia loadings. It revealed that lignite activated coke (LAC)-based MBBR performed more stable with phenols increasing (250-550 mg/L), and reached higher tolerance limit to ammonia (>320 mg/L) than activated carbon (AC)-based MBBR under fluctuant ammonia loadings. During the phenols-ammonia synchronous removal process, the LAC provided the firm basis for shock resistance due to superior resilient adsorption capacity, enhanced sludge property and microbial cooperation. Furthermore, microbial analysis revealed that the strengthened collaboration between archaea and facultative bacteria played the primary role in phenols-ammonia synchronous degradation. Specifically, the heterotrophic bacteria consumed phenols-ammonia by partial nitrification process and ammonia assimilation, following by denitrifying process to further eliminate phenols. The multifunctional Comamonas was the critical genus participating in all procedures.

Investigating the most appropriate methods for attached solids determination in moving-bed biofilm reactors

Moving-bed biofilm reactors (MBBR) have been employed worldwide as an efficient technology for the treatment of a diverse set of wastewaters. Although the attached biomass represents the major fraction of solids in MBBR systems, there is still no standard for its reliable quantification. An extensive literature review indicated that several methods for attached biomass assessment are applied, hindering the comparability of results issued from different studies. Therefore, the most reported methods for biofilm quantification in the MBBR literature were compared using three different carriers. The results revealed that the performance of each method was biased depending on the carrier type and shape. Moreover, differences in total attached solids (TAS) concentrations varied from 13% up to more than 90%, depending on the employed method for a given carrier. Overall, direct weighing of the carrier containing the biofilm, accounting for the clean carrier weight, and manual extraction of the biofilm, preceded or not by sonication for at least 15 min, were the most suitable techniques for assessing TAS and the volatile/total solids ratio in non-porous medias, respectively. The results here presented may be used as a frame of reference for standardization of the methods for assessing the biofilm mass in MBBR carriers.

Performance and diversity responses of nitrifying biofilms developed on varied materials and topographies to stepwise increases of aeration

Nitrifying biofilms were grown on 3D-printed nylon with three different surface characteristics (flat, millimeter-scale indentations, and indentations with activated carbon (AC) coating) and were subjected to sequentially increasing aeration-based shear to determine the interplay between surface, performance, and microbial populations towards improved design of wastewater treatment media. Biofilms were evaluated for nitrification, biomass detachment, and microbial composition based on Illumina 16s rRNA sequencing. Indentations provided greater stability over flat with respect to population diversity after detachment events but did not improve ammonia removal. AC-surface biofilm had significantly higher removal than uncoated surfaces at low aeration (1.0 L/min, fine) and significantly lower at high aeration (5.0 L/min, coarse). Principal component analyses of microbial communities illustrated temporal shifts over two similar cycles of growth and shear-induced biomass loss, demonstrating that biofilms grew similar consortia across all surfaces, but tended to revert to earlier individual compositions after shear events.

Identification and function of extracellular protein in wastewater treatment using proteomic approaches: A minireview

Microbial extracellular proteins serve as important functions in wastewater treatment process. Analysis of their compositions and properties is crucial to probe their specific functions. However, conventional analytical techniques cannot obtain interest protein information from complex proteins. Recently, the extracellular proteomics method has been applied to resolve the composition of extracellular proteins. In order to better understand the roles of extracellular protein in wastewater treatment process, this review provides the information on the proteomics methods and their application in investigating extracellular proteins involved in microbial attachment/aggregation, biodegradation of pollutants, and response to environmental stresses. Future work needs to exploit the full capability of the proteome.

Enhanced simultaneous nitri-denitrification in aerobic moving bed biofilm reactor containing polyurethane foam-based carrier media

Fluidization of carrier media for biofilm support and growth defines the moving bed biofilm reactor (MBBR) process. Major MBBR facilities apply virgin polyethylene (PE)-based circular plastic carrier media. Various carriers were studied to replace these conventional carriers, but polyurethane (PU) foam-based carrier media has not been much explored. This study evaluates the potential of PU foam carrier media in aerobic MBBR process for simultaneous nitri-denitrification (SND). Two parallel reactors loaded with conventional PE plastic (circular) and PU foam (cubical) carriers compared for their removal efficiencies of chemical oxygen demand (COD) and nitrogen contaminants from wastewater. Results indicate that average COD removal in MBBR containing PE plastic carrier media was 81%, compared to 83% in MBBR containing PU foam. Average ammonical and total nitrogen reduction was 71% and 59% for PU foam-based MBBR, compared to 60% and 42% for PE plastic-based MBBR. SND-based nitrogen removal capacity was doubled in aerobic MBBR filled with PU foam carrier media (27%), than MBBR containing PE plastic carrier media (13%). Cost economics also governs the commercial advantage for the application of PU foam-based carrier media in the MBBR process.

Sludge cake and biofilm formation as valuable tools in wastewater treatment by coupling Integrated Fixed-film Activated Sludge (IFAS) with Self Forming Dynamic Membrane BioReactors (SFD-MBR)

Two lab-scale Self Forming Dynamic Membrane BioReactors (SFD-MBR), equipped with 50 µm nylon meshes were set up and operated for the treatment of real municipal wastewater. Plastic carriers were added in one of the two bioreactors to generate a combination of the Integrated Fixed-film Activated Sludge (IFAS) and the SFD-MBR technologies. Overall, the two systems performed very well, achieving excellent effluent quality under steady state conditions and showing good resilience to extreme organic loading conditions. Continuous air scouring and periodical mesh cleaning by jet rinsing with tap water were effective in maintaining stable and high productivity (membrane flux around 67 L m² h^-1) over a period of 140 days. The application of the IFAS process resulted in lower production of excess sludge and improved denitrification. On the other hand, under the tested conditions the combined IFAS-SFD-MBR showed a higher tendency to mesh clogging with respect to the SFD-MBR.

Influence of carrier media physical properties on start-up of moving attached growth systems

Five carrier media with different shapes (spherical and cylindrical), sizes, voidage and protected surface areas (112-610 m²/m³) were studied in a pilot scale moving bed biofilm reactor (MBBR). This study aimed at assessing start-up duration using biofilm formation rates. Results indicated that the spherical media required shorter periods to achieve stable biofilm formation rates associated with chemical oxygen demand (COD) (15-17 days), compared to cylindrical high surface area media (23-24 days). Protected surface area presented weaker correlations with the biofilm formation rate for COD (R² = 0.83) and ammonia removal (R² = 0.76). However, good correlations were observed with a combination of the media physical factors: dimensionality (Di), voidage (Voi), and hydraulic efficiency (HE) strongly correlated with biofilm formation rates for heterotrophic (R² = 0.95) and nitrifying bacteria (R² = 0.92). This study proposes that the media physical properties can contribute to shortening start-up, contributing to improved removal rates and fast commissioning of MBBRs.

Cell membrane characteristics and microbial population distribution of MBBR and IFAS with different dissolved oxygen concentration

This paper investigated the influences of different dissolved oxygen (DO) concentration (0.71-1.32, 2.13-3.02 and 4.31-5.16 mg/L) on cell membrane characteristics and microbial population distribution of moving biofilm reactors. Two representative reactors, i.e., moving bed biofilm reactors and integrated fixed-film activated sludge were operated. Results indicated that both DO concentration of 0.71-1.32 mg/L and 4.31-5.16 mg/L could increase membrane lipid mobile fraction (49.4%-67.4%) of the microbes, however, through prompting the synthesis of branched fatty acids and unsaturated fatty acids, respectively. For the biofilms, the abundance of Bacteroidetes decreased and Actinobacteria increased with the increase of DO levels. The lowest EfOM content and the highest microbial diversities (1.14-1.52) was observed at DO of 2.13-3.02 mg/L. Redundancy analysis showed that changes of DO levels could alter cell membrane properties and bacterial community structures, and subsequently significantly influenced effluent organic matter composition of moving biofilm reactors.