The relative roles of sorption and biodegradation in the removal of contaminants of emerging concern (CECs) in GAC-sand biofilters

Biological degradation of organic micropollutants in GAC filters-temporal development and spatial variations

The capacity for organic micropollutant removal in granular activated carbon (GAC) filters for wastewater treatment changes over time. These changes are in general attributed to changes in adsorption, but may in some cases also be affected by biological degradation. Knowledge on the degradation of organic micropollutants, however, is scarce. In this work, the degradation of micropollutants in several full-scale GAC and sand filters was investigated through incubation experiments over a period of three years, using 14C-labeled organic micropollutants with different susceptibilities to biological degradation (ibuprofen, diclofenac, and carbamazepine), with parallel 16S rRNA gene sequencing. The results showed that the degradation of diclofenac and ibuprofen in GAC filters increased with increasing numbers of bed volumes when free oxygen was available in the filter, while variations over filter depth were limited. Despite relatively large differences in bacterial composition between filters, a degradation of diclofenac was consistently observed for the GAC filters that had been operated with high influent oxygen concentration (DO >8 mg/L). The results of this comprehensive experimental work provide an increased understanding of the interactions between microbial composition, filter material, and oxygen availability in the biological degradation of organic micropollutants in GAC filters.

Removal of organic micropollutants in biologically active filters: A systematic quantitative review of key influencing factors

Biofiltration utilizes natural mechanisms including biodegradation and biotransformation along with other physical processes for the removal of organic micropollutants (OMPs) such as pharmaceuticals, personal care products, pesticides and industrial compounds found in (waste)water. In this systematic review, a total of 120 biofiltration studies from 25 countries were analyzed, considering various biofilter configurations, source water types, biofilter media and scales of operation. The study also provides a bibliometric analysis to identify the emerging research trends in the field. The results show that granular activated carbon (GAC) either alone or in combination with another biofiltration media can remove a broad range of OMPs efficiently. The impact of pre-oxidation on biofilter performance was investigated, revealing that pre-oxidation significantly improved OMP removal and reduced the empty bed contact time (EBCT) needed to achieve a consistently high OMP. Biofiltration with pre-oxidation had median removals ranging between 65% and >90% for various OMPs at 10-45 min EBCT with data variability drastically reducing beyond 20 min EBCT. Biofiltration without pre-oxidation had lower median removals with greater variability. The results demonstrate that pre-oxidation greatly enhances the removal of adsorptive and poorly biodegradable OMPs, while its impact on other OMPs varies. Only 19% of studies we reviewed included toxicity testing of treated effluent, and even fewer measured transformation products. Several studies have previously reported an increase in effluent toxicity because of oxidation, although it was successfully abated by subsequent biofiltration in most cases. Therefore, the efficacy of biofiltration treatment should be assessed by integrating toxicity testing into the assessment of overall removal.

Contaminants of emerging concern reduction and microbial community characterization across a three-barrier advanced water treatment system

This research investigated the removal of contaminants of emerging concern (CECs) and characterized the microbial community across an advanced water treatment (AWT) train consisting of Coagulation/Flocculation/Clarification/Granular Media Filtration (CFCGMF), Ozone-Biological Activated Carbon Filtration (O3/BAC), Granular Activated Carbon filtration, Ultraviolet Disinfection, and Cartridge Filtration (GAC/UV/CF). The AWT train successfully met the goals of CECs and bulk organics removal. The microbial community at each treatment step of the AWT train was characterized using 16S rRNA sequencing on the Illumina MiSeq platform generated from DNA extracted from liquid and solid (treatment media) samples taken along the treatment train. Differences in the microbial community structure were observed. The dominant operational taxonomic units (OTU) decreased along the treatment train, but the treatment steps did impact the microbial community composition downstream of each unit process. These results provide insights into microbial ecology in advanced water treatment systems, which are influenced and shaped by each treatment step, the microbial community interactions, and their potential metabolic contribution to CECs degradation.

Deciphering the synergistic effects of photolysis and biofiltration to actuate elimination of estrogens in natural water matrix

The presence of estrogens in water environments has raised concerns for human health and ecosystems balance. These substances possess potent estrogenic properties, causing severe disruptions in endocrine systems and leading to reproductive and developmental problems. Unfortunately, conventional treatment methods struggle to effectively remove estrogens and mitigate their effects, necessitating technological innovation. This study investigates the effectiveness of a novel sequential photolysis-granular activated carbon (GAC) sandwich biofiltration (GSBF) system in removing estrogens (E1, E2, E3, and EE2) and improving general water quality parameters. The results indicate that combining photolysis pre-treatment with GSBF consistently achieved satisfactory performance in terms of turbidity, dissolved organic carbon (DOC), UV254, and microbial reduction, with over 77.5 %, 80.2 %, 89.7 %, and 92 % reduction, respectively. Furthermore, this approach effectively controlled the growth of microbial biomass under UV irradiation, preventing excessive head loss. To assess estrogen removal, liquid chromatography-tandem mass spectrometry (LC-MS) measured their concentrations, while bioassays determined estrogenicity. The findings demonstrate that GSBF systems, with and without photolysis installation, achieved over 96.2 % removal for estrogens when the spike concentration of each targeted compound was 10 µg L-1, successfully reducing estrogenicity (EA/EA0) to levels below 0.05. Additionally, the study evaluated the impact of different thicknesses of GAC layer filling (8 cm, 16 cm, and 24 cm) and found no significant difference (p>0.05) in estrogen and estrogenicity removal among them.

Antibiotic resistance genes and the association with bacterial community in biofilms occurring during the drinking water granular activated carbon (GAC) sandwich biofiltration

The granular activated carbon (GAC) sandwich modification to slow sand filtration could be considered as a promising technology for improved drinking water quality. Biofilms developed on sand and GAC surfaces are expected to show a functional diversity during the biofiltration. Bench-scale GAC sandwich biofilters were set-up and run continuously with and without antibiotic exposure. Surface sand (the schmutzdecke) and GAC biofilms were sampled and subject to high-throughput qPCR for antibiotic resistance gene (ARG) analysis and 16 S rRNA amplicon sequencing. Similar diversity of ARG profile was found in both types of biofilms, suggesting that all ARG categories decreased in richness along the filter bed. In general, surface sand biofilm remained the most active layer with regards to the richness and abundance of ARGs, where GAC biofilms showed slightly lower ARG risks. Network analysis suggested that 10 taxonomic genera were implicated as possible ARG hosts, among which Nitrospira, Methyloversatilis and Methylotenera showed the highest correlation. Overall, this study was the first attempt to consider the whole structure of the GAC sandwich biofilter and results from this study could help to further understand the persistence of ARGs and their association with the microbial community in drinking water biofiltration system.

Fate of emerging contaminants in a sequencing batch reactor and potential of biological activated carbon as tertiary treatment for the removal of persisting contaminants

The study aims to understand the occurrence and removal of 20 emerging contaminants (ECs) in each unit process of a sequencing batch reactor-based wastewater treatment plant (WWTP) and explore the potential of biological activated carbon (BAC) for the treatment of residual ECs and organic matter in the secondary effluent. Analgesic-acetaminophen, anti-inflammatory drug-ibuprofen, and stimulant-caffeine were detected at high concentrations in the influent. Most of the removal was observed in the biological treatment stage in the SBR basins. The mass load of the ECs was 2.93 g/d in the secondary effluent and 0.4 g/d in the final sludge, while the total removal of the mass load of ECs till the secondary treatment stage was 93.22%. 12 of the 20 ECs were removed by more than 50%, while carbamazepine (negative removal), sulfamethoxazole, and trimethoprim were removed by less than 20%. As a polishing step and to remove residual ECs, two BAC units were studied for 11,000 bed volumes (324 days). Packed column studies on granular activated carbon were conducted, and GAC development to BAC was monitored. SEM and FTIR were used to confirm and characterize the BAC. The BAC appeared to be more hydrophobic than the GAC. The BAC removed 78.4% and 40% of the dissolved ECs and organic carbon at an optimum EBCT of 25 min. Carbamazepine, sulfamethoxazole, and trimethoprim were removed by 61.5, 84, and 52.2%, respectively. Parallel column tests revealed adsorption as an important mechanism for the removal of positively charged compounds. The results indicate that the BAC is an effective tertiary/polishing technique for removing organic and micropollutants in the secondary wastewater effluent.

Emerging environmental contaminants: A global perspective on policies and regulations

Emerging contaminants include many synthetic or natural substances, such as pharmaceuticals and personal care products, hormones, and flame retardants that are not often controlled or monitored in the environment. The consumption or use of these substances is on an ever-rising trend, which dangerously increases their prevalence in practically all environmental matrices. These contaminants are present in low environmental concentrations and cause severe effects on human health and the biota. The present review analyzed 2012-2022 years papers via PubChem, science direct, National Center for Biotechnology Information, web of science on the legislations and policies of emerging contaminants globally. A state-of-the-art review of several studies in the literature focus on examining and evaluating the emerging contaminants and the frameworks adopted by developed and developing countries to combat the release of emerging contaminants and form footprints towards water sustainability which includes water availability, usage patterns, generation and pollution management, the health of aquatic systems, and societal vulnerability. The paper aims to provide a comprehensive view of current global policies and framework regarding evaluating and assessing the chemicals, in light of being a threat to the environment and biota. The review also highlights the future global prospects, including current governmental activities and emerging contaminant policy measures. The review concludes with suggestions and way forward to control the inventory and disposal of emerging contaminants in the environment.

Multi-scale Investigation of Ammonia-Oxidizing Microorganisms in Biofilters Used for Drinking Water Treatment

Ammonia-oxidizing microorganisms (AOMs) include ammonia-oxidizing bacteria (AOB), archaea (AOA), and Nitrospira spp. sublineage II capable of complete ammonia oxidation (comammox). These organisms can affect water quality not only by oxidizing ammonia to nitrite (or nitrate) but also by cometabolically degrading trace organic contaminants. In this study, the abundance and composition of AOM communities were investigated in full-scale biofilters at 14 facilities across North America and in pilot-scale biofilters operated for 18 months at a full-scale water treatment plant. In general, the relative abundance of AOM in most full-scale biofilters and in the pilot-scale biofilters was as follows: AOB > comammox Nitrospira > AOA. The abundance of AOB in the pilot-scale biofilters increased with increasing influent ammonia concentration and decreasing temperature, whereas AOA and comammox Nitrospira exhibited no correlations with these parameters. The biofilters affected AOM abundance in the water passing through the filters via collecting and shedding but exhibited a minor influence on the composition of AOB and Nitrospira sublineage II communities in the filtrate. Overall, this study highlights the relative importance of AOB and comammox Nitrospira compared to AOA in biofilters and the influence of filter influent water quality on AOM in biofilters and their release into the filtrate.

Sand and sand-GAC filtration technologies in removing PPCPs: A review

Concerns have been raised about the risks that pharmaceuticals and personal care products (PPCPs) in aquatic environments posed to humans and the environment. In recent years, sand filtration has been used to potentially remove these emerging contaminants from water. However, there has been no review of the effectiveness of this technology to date. This paper presents a brief introduction of sand filtration types, reviews the current progress in PPCPs removal through sand filtration, and discusses the mechanisms behind this process and the combination of granular activated carbon (GAC) and sand as an enhanced sand-GAC filtration technology. Sand filtration achieves a reasonable but highly variable degree of PPCPs removal. Biodegradation and adsorption are the two main mechanisms of PPCPs removal, in particular the biodegradation since adsorption capacity of sand is relatively low. Other processes, such as bio-sorption and indirect adsorption, may also contribute to PPCPs removal. To compensate for the inadequate PPCPs removal through sand filtration, porous GAC has been combined with sand to develop sand-GAC filtration technologies. Serial, dual, and sandwich filters have been investigated, and significant removal enhancement has been observed, due to the strengthened adsorption capacity, suggesting the applicability of these variants. Future research focus, such as investigating the influence of different operational conditions on sand filter performance, obtaining a deeper understanding of the various removal mechanisms, and investigating of long-term performance of the filter used for PPCPs removal, are suggested.

Is In-Service Granular Activated Carbon Biologically Active? An Evaluation of Alternative Experimental Methods to Distinguish Adsorption and Biodegradation in GAC

In-service granular activated carbon (GAC) may transform into biological activated carbon (BAC) and remove contaminants through both adsorption and biodegradation, but it is difficult to determine its biodegradative capacity. One approach to understand the GAC biodegradative capacity is to compare the performance between unsterilized and sterilized GAC, but the sterilization methods may not ensure effective microbial inhibition and may affect adsorption. This study identified the ¹⁴C-glucose respiration rate as the best metric to evaluate the effectiveness of three sterilization methods: sodium azide addition, autoclaving, and γ irradiation. The sterilization protocols were refined, including continuously feeding 300 mg/L of sodium azide, three cycles of autoclaving, and 10-12 kGy of γ irradiation. Parallel minicolumn tests were conducted to identify sodium azide addition as the most broadly effective sterilization method with an insignificant effect on adsorption in most cases, except for the adsorption of anionic compounds under certain conditions. Nevertheless, this problem was solved by decreasing the azide dosage as long as it is still sufficient to provide effective microbial inhibition. This study helps to develop an approach that differentiates adsorption and biodegradation in GAC, which could be used by future studies to advance our understanding of BAC filtration.

Consumption and ocurrence of antidepressants (SSRIs) in pre- and post-COVID-19 pandemic, their environmental impact and innovative removal methods: A review

Selective serotonin reuptake inhibitors (SSRIs) are pharmaceuticals whose consumption has increased significantly. They are prescribed as first-line treatment in mental disorders such as depression, obsessive-compulsive disorder, phobias, and anxiety; also, they are indicated as adjuvants in diseases such as fibromyalgia and bulimia nervosa. In addition to being linked to the illegal market to be consumed as recreational drugs. The relevance of this review lies in the fact that worldwide consumption has increased significantly during the COVID-19 pandemic, due to the depression and anxiety that originated in the population. As a consequence of this increase in consumption, concentrations of SSRIs in the environment have increased, and these have become a relevant issue for toxicologists due to the effects that they could generate in different organisms, both aquatic and terrestrial. For this reason, the objective of this article was to do a critical evaluation of the existing data on the characteristics and physicochemical properties of SSRIs, consumption data during the COVID-19 pandemic, its occurrence in the environment and the reports of toxic effects that have been generated in different organisms; we also conclude with an updated review of different methods that have been used for their removal. With this analysis, it can be concluded that, despite SSRIs are pharmaceutical products widely studied since their launching to the market, still currently under investigation to clarify their mechanisms of action to understand the different effects on the organisms, adverse reactions, as well as possible toxicological effects on non-target organisms. On the other hand, it has been proven that although it is already possible to eliminate a significant percentage of SSRIs in the laboratory, due to their physicochemical characteristics and their behavior in complex mixtures in the environment, they have not yet been eradicated, showing a persistence in the soil, subsoil and surface waters of the entire planet that may represent a future risk.

Optimization of White-Rot Fungi Mycelial Culture Components for Bioremediation of Pharmaceutical-Derived Pollutants

White-rot fungi can degrade a wide spectrum of environmental pollutants, including pharmaceuticals, which are not efficiently removed from wastewater by conventional methods, e.g., the activated sludge method. However, the treatment of wastewater with the use of fungal cultures (mycoremediation) also has significant limitations: among others, the need to use appropriate, often-expensive culture media. We aimed to screen 18 media ingredients, including seven agrifood byproducts for Armillaria mellea, Phanerochaete chrysosporium and Pleurotus ostreatus in submerged cultures to select the low-cost medium optimal for biomass production and laccase activity. We screened nine mathematic models to describe the relation of fungal growth and the amount of the selected byproduct in media. Finally, we tested the ability of the strain with the highest mycelial growth and enzyme-producing ability in the selected medium to degrade eight drug contaminants. Three media variants composed of byproducts provided both efficient growth and laccase production: corn steep liquor + poplar, dried distillers grains with solubles + poplar and corn steep liquor 50%. Among the investigated growth models, the Han–Levenspiel equation described well the specific growth rate in function of the nominal substrate concentration in one-component media. Pleurotus ostreatus, the fungus with the highest ligninolytic enzyme activity, cultured in medium composed of corn steep liquor, removed six of eight drug contaminants with a removal degree of 20–90% in 48 h. The obtained data on the optimal culture media consisting of insoluble components provide initial data for upscaling the process and designing an appropriate type of bioreactor for the process of removing drug contaminants from water.

Understanding adsorption and biodegradation in granular activated carbon for drinking water treatment: A critical review

Drinking water treatment plants use granular activated carbon (GAC) to adsorb and remove trace organics, but the GAC has a limited lifetime in terms of adsorptive capacity and needs to be replaced before it is exhausted. Biological degradation of target contaminants can also occur in GAC filters, which might allow the GAC to remain in service longer than expected. However, GAC biofiltration remains poorly understood and unpredictable. To increase the understanding of adsorption and biodegradation in GAC, previous studies have conducted parallel column tests that use one column of GAC (potentially biologically active) to assess overall removal via both adsorption and biodegradation, and one column with either sterilized GAC or biological non-adsorbing media to assess adsorption or biodegradation alone. Mathematical models have also been established to give insight into the adsorption and biodegradation processes in GAC. In this review, the experimental and modeling approaches and results used to distinguish between the role of adsorption and biodegradation were summarized and critically discussed. We identified several limitations: (1) using biological non-adsorbing media in column tests might lead to non-representative extents of biodegradation; (2) sterilization methods may not effectively inhibit biological activity and may affect adsorption; (3) using virgin GAC coated with biofilm could overestimate adsorption; (4) potential biofilm detachment during column experiments could lead to biased results; (5) the parallel column test approach itself is not universally applicable; (6) competitive adsorption was neglected by previous models; (7) model formulations were based on virgin GAC only. To overcome these limitations, we proposed four new approaches: the use of gamma irradiation for sterilization, a novel minicolumn test, compound-specific isotope analysis to decipher the role of adsorption and biodegradation in situ, and a new model to simulate trace organic adsorption and biodegradation in a GAC filter .

Prolonged lifetime of biological activated carbon filters through enhanced biodegradation of melamine

Micropollutants can be removed in Biological Activated Carbon (BAC) filters through biodegradation, besides adsorption, when the conditions are favorable. In the present study, we build upon previous work on melamine biodegradation and activated carbon regeneration in batch experiments and assess the efficiency of this process in continuous flow lab-scale BAC filters. Melamine is frequently detected at low concentrations in surface water and is used here as a model micropollutant. BAC filters were inoculated with melamine degrading biomass and the contribution of biodegradation to melamine removal was assessed. Furthermore, we tested the effect of an additional carbon source (methanol) and the effect of contact time on melamine removal efficiency. We demonstrate that inoculation of activated carbon filters with melamine degrading biomass increases melamine removal efficiency by at least 25%. When an additional carbon source (methanol) is supplied, melamine removal is almost complete (up to 99%). Finally, through a nitrogen mass balance, we demonstrate that around 60% of the previously adsorbed melamine desorbs from the BAC surface when biodegradation rates in the liquid phase increase. Melamine desorption resulted in a partial recovery of the adsorption capacity.

Control of disinfection byproducts in drinking water treatment plants: Insight into activated carbon filter

The removal efficiencies of disinfection byproducts formation potentials (DBPFPs) and generated DBPs under pre-chlorination condition (pre-generated DBPs) during different drinking water treatment trains in eight full-scale drinking water treatment plants (WTPs) were investigated through field and laboratory studies. Haloacetic acids (HAAs) and haloacetonitriles (HANs) were identified to be two representative DBPs based on cytotoxicity and genotoxicity assessments. The performances of advanced treatment train for HAAs and HANs were better than that of conventional treatment train. However, the efficacy of ozone - biological activated carbon (O₃-BAC) was affected by its service time and position in the water treatment process. In addition, the consumption of free chlorine by activated carbon in old granular activated carbon (GAC) filter was higher than that in new one under pre-chlorination condition, resulting in the increase of HAAs and HANs in the GAC filter effluent. This demonstrated that the organic matter adsorbed on older activated carbon generated more HAAs and HANs during pre-chlorination, which inhibited the adsorption of pre-generated DBPs. The ability of GAC/O₃-BAC to remove HAAs and HANs was consistent with that of protein-like and low molecular weight organic substances, which could predict the performance of GAC and O₃-BAC in treating DBPs.

Environmental and health impacts of contaminants of emerging concerns: Recent treatment challenges and approaches

In the past few decades, new contaminants of emerging concern (CECs) in the air, water, and soil have gained significant attention due to their adverse impact on human health and the environment. The sources of CECs have been identified in different forms from domestic and industrial activities such as personal care products and pharmaceuticals. It has been established that aqueous medium plays a major role in the dissemination of various contaminants, like drinking water, reservoirs, lakes, rivers and waste with water medium. There remains inadequate technology for the treatment of CECs in the wastewater systems. Though different techniques have advanced for the treatment of CECs, they still pose a severe threat to human health and disturb the ecological balance. In this review, the characteristics, recent technologies, risk assessment and management of CECs have been discussed. The primary aim is to highlight the new innovative and cost-effective technologies for the remediations of CECs in all forms. Biochar is readily and economically available in abundance and an economical adsorbent with 100% adsorptive removal for H₂PO₄^-. The bibliometric analysis also performed to understand the emerging research trends on the treatment techniques, which can help in developing a guiding pathway to modern research in academia and industry.

Removal efficiency of emerging micropollutants in biofilter wastewater treatment plants in tropical areas

We studied the removal of 61 emerging micropollutants, including illicit drugs, in a biofilter wastewater treatment plant located in the French Indies (Martinique). Raw wastewater concentrations were the highest for paracetamol followed by caffeine, naproxen, ibuprofen, its metabolite 2-hydroxyibuprofen, atenolol, ketoprofen, furosemide, methylparaben, cocaine, benzoylecgonine, and 11-nor-delta-9-carboxytetrahydrocannabinol (THC-COOH). The calculated removals were better than those reported in the literature, while the cumulative removal efficacy (i.e., removal of the total mass load) was estimated to be 92 ± 4%. However, this good performance may be partly explained by the removal of paracetamol (also named acetaminophen) and caffeine, which represented 86.4% of the total mass load. Our results point to the adsorption of some molecules on sludge, thus raising the question about local soil pollution from sludge spreading.

Powdered activated carbon (PAC) amendment enhances naphthalene biodegradation under strictly sulfate-reducing conditions

Capping represents an efficient and well-established practice to contain polycyclic aromatic hydrocarbons (PAHs) in sediments, reduce mobility, and minimize risks. Exposure to PAHs can encourage biodegradation, which can improve the performance of capping. This study investigates biodegradation of naphthalene (a model PAH) in highly reducing, sediment-like environments with amendment of different capping materials (PAC and sand). Microcosms were prepared with sediment enrichments, sulfate as an electron acceptor, and naphthalene. Results show that PAC stimulates naphthalene biodegradation and mineralization, as indicated by production of ¹⁴CO₂ from radiolabeled naphthalene. Mineralization in PAC systems correlates with the enrichment of genera (Geobacter and Desulfovirga) previously identified to biodegrade naphthalene (Spearman's, p < 0.05). Naphthalene decay in sand and media-free systems was not linked to biodegradation activity (ANOVA, p > 0.05), and microbial communities were correlated to biomass yields rather than metabolites. Naphthalene decay in PAC systems consists of three stages with respect to time: latent (0-88 days), exponential decay (88-210 days), and inactive (210-480 days). This study shows that PAC amendment enhances naphthalene biodegradation under strictly sulfate-reducing conditions and provides a kinetic and metagenomic characterization of systems demonstrating naphthalene decay.

Differentiating between adsorption and biodegradation mechanisms while removing trace organic chemicals (TOrCs) in biological activated carbon (BAC) filters

Efficient adsorption of certain trace organic chemicals (TOrCs) present in secondary treated municipal wastewater treatment plant (WWTP) effluents onto granular activated carbon (GAC) has already been demonstrated at lab- and full-scale. Due to high organic matter concentrations in WWTP effluents, GAC filters eventually develop a biofilm and turn into biological activated carbon filters (BAC), where removal of organic compounds is governed by biodegradation as well as by adsorption. However, determining TOrC breakthrough by conducting a long-term BAC column experiment to discern between the removal mechanisms is not possible due to competition for adsorption sites, fluctuating water quality, and other variables. Therefore, a rapid small scale column test (RSSCT) was conducted to determine the contribution of adsorption for select chemicals at 10,000 bed volumes treated (BVT). These results were then used in the pore surface diffusion model (PSDM) to model adsorption behavior at 40,000 BVTs. Pseudo-Freundlich K values obtained from the PSDM model were compared with K values obtained from an integral mass balance calculation. This comparison revealed that the modeling was most accurate for moderately to poorly adsorptive compounds. In comparing RSSCT results to long-term BAC columns, the modeling approach best predicted BAC removal of well adsorbing compounds, such as atenolol, trimethoprim, metoprolol, citalopram, and benzotriazole. However, differences in predicted vs observed BAC removal for the removals of venlafaxine, tramadol and carbamazepine revealed that BAC adsorption capacity was not yet exhausted for these compounds. Therefore, a comparison was not possible. The approach would be improved by operation at longer EBCT and improved calculation of compound fouling indices.

Removal of micropollutants in drinking water using UV-LED/chlorine advanced oxidation process followed by activated carbon adsorption

This study investigated the removal of three selected micropollutants (i.e., bisphenol A, diclofenac and caffeine) in drinking water using the UV-LED/chlorine advanced oxidation process (AOP) followed by activated carbon adsorption. The degradation of bisphenol A, diclofenac and caffeine was predominantly contributed by chlorination (>60%), direct UV photolysis (>80%) and radical oxidation (>90%), respectively, during the treatment by the UV-LED/chlorine AOP at three tested UV wavelengths (i.e., 265, 285 and 300 nm). The most effective UV wavelengths for the degradation of bisphenol A, diclofenac and caffeine were 265, 285 and 300 nm, respectively. The degradation of all the three micropollutants was enhanced with increasing pH from 6 to 8, though the reasons for the pH dependence were different. The residues of the micropollutants and their degradation (by)products were removed by post-adsorption using granular activated carbon (GAC). Interestingly and more importantly, the adsorption rates of the degradation (by)products were 2-3 times higher than the adsorption rates of the corresponding micropollutants, indicating the formation of more adsorbable (by)products after the AOP pre-treatment. The UV-LED/chlorine AOP followed by GAC adsorption provides a multi-barrier treatment system for enhancing micropollutant removal in potable water. The findings also suggest the merit of the sequential use of UV-LEDs followed by GAC in treating chlorine-containing potable water in small-scale water treatment systems (e.g., point-of-use or point-of-entry water purifiers).

Microbiome of Drinking Water Biofilters is Influenced by Environmental Factors and Engineering Decisions but has Little Influence on the Microbiome of the Filtrate

Bacterial communities in biofilters can improve drinking water quality through the biodegradation of dissolved contaminants but also pose potential risks by harboring and shedding microbes into the drinking water distribution system. In this study, pilot-scale granular activated carbon (GAC)-sand and anthracite-sand pilot-scale biofilters were investigated to determine the effects of filter design and operation on the microbiome of the filter media and its relationship to the microbiome in the filter effluent water. Bacterial abundance in the biofilters was relatively stable over time. Bacterial community composition exhibited spatial variation (i.e., with bed depth) and temporal variation linked to water quality changes. Bacterial community composition was significantly affected by the media type (GAC vs anthracite) and backwashing strategy (chloraminated water vs nonchloraminated water). The biofilters reduced bacterial abundance in the water (∼70%) but had only a minor effect on the bacterial community composition in the filtrate. Overall, our results suggest that the bacterial communities growing on biofilters affect filtered water quality primarily through the biotransformation of pollutants and nutrients rather than by altering the microbial community composition of the water as it passes through the filter.

Extended field investigations of ozone-biofiltration advanced water treatment for potable reuse

Recovering and reusing treated wastewater effluent is a sustainable and cost-effective practice for addressing global water sustainability. To date, most potable reuse advanced water treatment (AWT) solutions are based on reverse osmosis (RO), which generates a continuous reject stream of concentrated brine waste. Ozone-biofiltration based solutions have been investigated as a potential alternative for RO. However, implementation of ozone-biofiltration for potable reuse projects around the world has been limited. The goal of this study was to conduct an extended field investigation of ozone-biofiltration treatment to address regulatory, design, and operational hurdles that may hinder implementation in water-short areas. For 16 months, two parallel biological activated carbon (BAC) filters were operated at empty bed contact times (EBCTs) of 10 min and 20 min treating up to 60,000 and 30,000 bed volumes (BVs), respectively, of sand filtered effluent from a municipal wastewater treatment process. BAC 1 (EBCT = 10 min) and BAC 2 (EBCT = 20 min) used Calgon Filtrasorb 400 granular activated carbon (GAC) as filter media, with equal bed depths of 0.8 m. Increasing the specific ozone dose from 0.9 to 2.0 provided a muted response with respect to oxidation of contaminants of emerging concern (CECs) that are resistive to ozonation. N-Nitrosodimethylamine (NDMA) was generated during ozonation, with the average concentration of NDMA in ozonated effluent being 40.4 ng/L. In BAC 1 (EBCT = 10 min), NDMA was fully removed during the first month of study (<2000 BVs), partially removed between 2000 and 20,000 BVs, and completely removed when monitored between 57,000 and 62,000 BVs. These trends clearly reveal time-dependent interactions between carbon-based (e.g., adsorption) and non-carbon-based (e.g., biodegradation) removal mechanisms. In BAC 2 (EBCT = 20 min), almost all CECs, excluding NDMA, were removed consistently throughout the study (through ∼30,000 BVs). This indicates a somewhat different interaction between carbon-based and non-carbon-based removal in the more lightly loaded BAC 2, compared to BAC 1. After 482 days of operation, BAC 1 (EBCT = 10 min) produced effluent with lower NDMA concentration (<2 ng/L) than BAC 2 (10 ng/L), confirming prior evidence of cometabolic NDMA biodegradation pathways operable in more heavily loaded BACs. These findings emphasize the need for extended field testing (50,000 BVs or greater). BAC 1 removed TOC in effluent until it plateaued at around 6 mg/L after 60,000 BVs, whereas BAC 2 effluent plateaued at around 4 mg/L. Under plateau conditions, BAC 1 and BAC 2 with sand filter pretreatment and ozonation appear to have a gross TOC removal potential of around 0.2-0.3 kg of TOC removed per day per cubic meter of carbon media (kg/d/m³). A comparative analysis of findings from this study and results from a past ozone-BAC study in the Reno area (termed BAC 3 operated downstream of membrane filter with an EBCT of 30 min) shows that higher TOC removal was observed in BAC with shorter EBCT and upstream sand filter compared to BAC with longer EBCT and upstream membrane filter. The present study addresses the regulatory and financial concerns associated with ozone-BAC performance in potable reuse applications. Improved comprehension of ozone-BAC performance, coupled with its reduced capital and operations and maintenance (O&M) costs compared to RO, may accelerate the full-scale implementation of ozone-BAC treatment as a sustainable solution for the rapidly emerging potable reuse market.

Effects of geographic location and water quality on bacterial communities in full-scale biofilters across North America

Spatial patterns of bacterial community composition often follow a distance-decay relationship in which community dissimilarity increases with geographic distance. Such a relationship has been commonly observed in natural environments, but less so in engineered environments. In this study, bacterial abundance and community composition in filter media samples (n = 57) from full-scale rapid biofilters at 14 water treatment facilities across North America were determined using quantitative polymerase chain reaction and Illumina HiSeq high-throughput sequencing targeting the 16S rRNA gene, respectively. Bacteria were abundant on the filter media (108.8±0.3 to 1010.7±0.2 16S rRNA gene copies/cm3 bed volume) and the bacterial communities were highly diverse (Shannon index: 5.3 ± 0.1 to 8.4 ± 0.0). Significant inter-filter variations in bacterial community composition were observed, with weighted UniFrac dissimilarity values following a weak but highly significant distance-decay relationship (z = 0.0057 ± 0.0006; P = 1.8 × 10-22). Approximately 50% of the variance in bacterial community composition was explained by the water quality parameters measured at the time of media sample collection (i.e. pH, temperature and dissolved organic carbon concentration). Overall, this study suggested that the microbiomes of biofilters are primarily shaped by geographic location and local water quality conditions but the influence of these factors on the microbiomes is tempered by filter design and operating conditions.

Selection and evaluation of water pretreatment technologies for managed aquifer recharge (MAR) with reclaimed water

Managed aquifer recharge with reclaimed water is a promising strategy for indirect potable reuse. However, residual contaminants in the treated wastewater effluent could potentially have adverse effects on human health. Hence, adequate water pretreatment is required. A multi-criteria approach was used to select and evaluate suitable water pretreatment technologies that can remove these critical contaminants in wastewater effluent for MAR identified in a previous study (Yuan et al., 2017). The treatment efficiency targets were calculated based on the concentrations and the suggested limits of critical contaminants. Treatment efficiency credits were then assigned to each treatment option for the removal of critical contaminants based on literature data. Treatment units that resulted in the highest efficiency credit scores were selected and combined into treatment train options, which were evaluated in terms of treatability, cost, and sustainability. This paper proposes an approach for the selection and evaluation of water treatment options, which will be helpful to guide the future implementation of MAR projects with reclaimed water.

Nontarget analysis: A new tool for the evaluation of wastewater processes

Strategies to determine the removal efficiency of micropollutants in wastewater treatment plants (WWTPs) are widely discussed. Especially the evaluation of the potential benefit of further advanced treatment steps such as an additional tertiary treatment based on ozonation or activated carbon have come into focus. Such evaluation strategies are often based on the removal behavior of known micropollutants via target or suspected analysis. The utilization of nontarget analysis is considered to lead to a more comprehensive picture as also unknown or not expected micropollutants are analyzed. Here, the results of an evaluation via target and nontarget analysis were compared for biological treatment (BT) processes of eleven full-scale WWTPs and three different post-treatments (PTs): one sand filter (SF) and two granular activated carbon (GAC) filters. The similarity of the determined removals from target and nontarget analysis of the BTs increased significantly by excluding easily degradable "features" from the nontarget evaluation. A similar ranking of the removal trends for the BTs could also be achieved by comparing this new subset of nontarget features with a set of nine readily to moderately biodegradable micropollutants. This observation suggests that a performance ranking of BTs based either on target or nontarget analysis is plausible. In contrast to the BTs, the evaluation of the three PTs revealed that the difference of feature removal between SF and the two GACs was small, but large for the target analytes with substantially higher removal effciencies for the GACs compared to the SF. In addition to the removal behavior, the nontarget analysis provided further information about the number and quantity of transformation products (TPs) in the effluent from the BTs. For all BTs more than half (55-67%) of the features detected in the effluent were not found in the influent. A comparable proportion of TPs was also detected after GAC and sand filtration due to their microbial activities.

Fate of environmental pollutants

This annual review covers the literature published in 2018 on topics related to the occurrence and fate of environmental pollutants in wastewater. Due to the vast amount of literature published on this topic, we have discussed only a portion of the quality research publications, due to the limitation of space. The abstract search was carried out using Web of Science, and the abstracts were selected based on their relevance. In a few cases, full-text articles were referred to understand new findings better. This review is divided into the following sections: antibiotic-resistant bacteria (ARBs) and antibiotic-resistant genes (ARGs), disinfection by-products (DBPs), drugs of abuse (DoAs), estrogens, heavy metals, microplastics, per- and polyfluoroalkyl compounds (PFAS), pesticides, and pharmaceuticals and personal care products (PPCPs), with the addition of two new classes of pollutants to previous years (DoAs and PFAS).