Probing the intermolecular interaction mechanisms between humic acid and different substrates with implications for its adsorption and removal in water treatment

Enhanced water decontamination via photogenerated electron delocalization of π → π* and D-π-A synergistically

Mixed-dimensional van der Waals heterojunctions (MD-vdWhs), known for exceptional electron transfer and charge separation capabilities, remain underexplored in photocatalysis. In this study, we leveraged the synergistic effect of intermolecular π → π* and D-π-A dual channels to fabricate novel MD-vdWhs. Owing to the synergistic effect, it exhibits superior electron transfer and delocalization ability, thereby enhancing its photocatalytic performance. The Optimal photocatalyst can degrade 98.78 % of 20 mg/L tetracycline (TC) within 15 min. Additionally, we introduced a novel proof strategy for investigating the photoelectron transfer path, creatively demonstrating the synergistic dual channels effect, which can be attributed to the carbonyl density and light-excitation degree. Notably, even under low-power light sources, it achieved complete inactivation of Escherichia coli within just 7 mins, far surpassing current cutting-edge research. This theoretical framework holds promise for broader applications within related studies.

Probing the Surface Layer Modulation on Archaeal Mechanics and Adhesion at the Single-Cell Level

Addressing the challenge of understanding how cellular interfaces dictate the mechanical resilience and adhesion of archaeal cells, this study demonstrates the role of the surface layer (S-layer) in methanogenic archaea. Using a combination of atomic force microscopy and single-cell force spectroscopy, we quantified the impact of S-layer disruption on cell morphology, mechanical properties, and adhesion capabilities. We demonstrate that the S-layer is crucial for maintaining cell morphology, where its removal induces significant cellular enlargement and deformation. Mechanical stability of the cell surface is substantially compromised upon S-layer disruption, as evidenced by decreased Young's modulus values. Adhesion experiments revealed that the S-layer primarily facilitates hydrophobic interactions, which are significantly reduced after its removal, affecting both cell-cell and cell-bubble interactions. Our findings illuminate the S-layer's fundamental role in methanogen architecture and provide a chemical understanding of archaeal cell surfaces, with implications for enhancing methane production in biotechnological applications.

Sluggish and Ion-Resilient Behavior of Interfacial Aqueous Layer on Single-Layer Graphene Oxide: Insights from In Situ Atomic Force Microscopy

Understanding interfacial interactions of graphene oxide (GO) is important to evaluate its colloidal behavior and environmental fate. Single-layer GO is the fundamental unit of GO colloids, and its interfacial aqueous layers critically dictate these interfacial interactions. However, conventional techniques like X-ray diffraction are limited to multilayer systems and are inapplicable to single-layer GO. Therefore, our study employed atomic force microscopy to precisely observe the in situ dynamic behaviors of interfacial aqueous layers on single-layer GO. The interfacial aqueous layer height was detected at the subnanometer level. In real-time monitoring, the single-layer height increased from 1.17 to 1.70 nm within 3 h immersion. This sluggish process is different from the rapid equilibration of multilayer GO in previous studies, underscoring a gradual transition in hydration kinetics. Ion strength exhibited negligible influence on the single-layer height, suggesting a resilient response of the interfacial aqueous layer to ion-related perturbations due to intricate ion interactions and electrical double-layer compression. Humic acid led to a substantial increase in the interfacial aqueous layers, improving the colloidal stability of GO and augmenting its potential for migration. These findings hold considerable significance regarding the environmental behaviors of the GO interfacial aqueous layer in ion- and organic-rich water and soil.

Unraveling Partial Coalescence Between Droplet and Oil-Water Interface in Water-in-Oil Emulsions under a Direct-Current Electric Field via Molecular Dynamics Simulation

When the electric field strength (E) surpasses a certain threshold, secondary droplets are generated during the coalescence between water droplets in oil and the oil-water interface (so-called the droplet-interface partial coalescence phenomenon), resulting in a lower efficiency of droplet electrocoalescence. This study employs molecular dynamics (MD) simulations to investigate the droplet-interface partial coalescence phenomenon under direct current (DC) electric fields. The results demonstrate that intermolecular interactions, particularly the formation of hydrogen bonds, play a crucial role in dipole-dipole coalescence. Droplet-interface partial coalescence is categorized into five regimes based on droplet morphology. During the contact and fusion of the droplet with the water layer, the dipole moment of the droplet exhibits alternating increases and decreases along the electric field direction. Electric field forces acting on sodium ions and the internal interactions within droplets promote the process of droplet-interface partial coalescence. High field strengths cause significant elongation of the droplet, leading to its fragmentation into multiple segments. The migration of hydrated ions has a dual impact on the droplet-interface partial coalescence, with both facilitative and suppressive effects. The time required for droplet-interface partial coalescence initially decreases and subsequently increases as the field strength increases, depending on the competitive relationship between the extent of droplet stretching and the electric field force. This work provides molecular insights into the droplet-interface coalescence mechanisms in water-in-oil emulsions under DC electric fields.

Sulfate Doping Promotes Agglomeration of Calcium Fluoride Crystals

Calcium salt precipitation is an effective solution to wastewater fluoride pollution. The purity and precipitation efficiency of calcium fluoride is critical for its removal and recovery. This study aimed to reveal the role of coexisting sulfates in the precipitation of calcium fluoride. A low sulfate concentration promoted calcium fluoride precipitation. The size of calcium fluoride-aggregated particle clusters increased from 750 to 2000 nm when the molar ratio of sulfate to fluoride was increased from 0 to 3:100. Sulfate doped in the calcium fluoride crystals neutralized the positive charge of the calcium fluoride. Online atomic force microscopy measurements showed that sulfate reduced the repulsive force between calcium fluoride crystals and increased the adhesion force from 1.62 to 2.46 nN, promoting the agglomeration of calcium fluoride crystals. Sulfate improved the precipitation efficiency of calcium fluoride by promoting agglomeration; however, the purity of calcium fluoride was reduced by doping. Sulfate reduced the induction time of calcium fluoride crystallization and improved the nucleation rate of calcium fluoride. Sulfate should be retained to improve the precipitation of calcium fluoride and to avoid its loss from the effluents. However, it is necessary to separate sulfate from fluoride to obtain high-purity calcium fluoride. Therefore, sulfate concentration regulation in high-fluoride wastewater is key to achieving the efficient removal and recovery of fluoride ions.

The role of magnesium ion in the interactions between humic acid and tetracycline in solution

Coexisting tetracycline (TC), dissolved organic matter (DOM), and metal cations in aqueous environments might form complexes and consequently affect the environmental fate of TC. In this study, the interactions among coexisting humic acid (HA), TC, and Mg(II) in solutions were investigated by equilibrium dialysis batch experiments and nuclear magnetic resonance hydrogen spectroscopy (1H NMR) characterization. In the binary systems, the dimethylamine (4Me2NH+) functional group on the A-ring of TC bound to the oxygen-containing functional groups of HA via hydrogen bond. The solution pH affected the agglomeration morphology and dissociation of the oxygen-containing functional groups of HA as well as protonation and spatial conformation of TC, which in turn affected the HA-TC interactions. The complexation sites and ratio of Mg(II) on TC affect the binding mode in the ternary system. When the TC-Mg(II) complexation ratio is 1:1, the B, C, and D rings of TC preferentially complex with Mg(II), resulting in the change of TC from an extended to a twisted conformation. At this time, Mg(II) had a weaker inhibitory effect on binding affinity between HA and TC. When the complexation ratio was 1:2, the second Mg(II) complexation deactivated the 4Me2NH + on the A ring and further stabilized TC twisted conformation, resulting in a stronger inhibitory effect on the binding of TC to HA. Under acidic conditions, the solution pH mainly caused the difficulty in forming TC-Mg(II) complexes. The inhibitory effect of Mg(II) on the binding between HA and TC is weaker than that under alkaline conditions.

Electrostatic coupling and water bridging in adsorption hierarchy of biomolecules at water-clay interfaces

Clay minerals are implicated in the retention of biomolecules within organic matter in many soil environments. Spectroscopic studies have proposed several mechanisms for biomolecule adsorption on clays. Here, we employ molecular dynamics simulations to investigate these mechanisms in hydrated adsorbate conformations of montmorillonite, a smectite-type clay, with ten biomolecules of varying chemistry and structure, including sugars related to cellulose and hemicellulose, lignin-related phenolic acid, and amino acids with different functional groups. Our molecular modeling captures biomolecule-clay and biomolecule-biomolecule interactions that dictate selectivity and competition in adsorption retention and interlayer nanopore trapping, which we determine experimentally by NMR and X-ray diffraction, respectively. Specific adsorbate structures are important in facilitating the electrostatic attraction and Van der Waals energies underlying the hierarchy in biomolecule adsorption. Stabilized by a network of direct and water-bridged hydrogen bonds, favorable electrostatic interactions drive this hierarchy whereby amino acids with positively charged side chains are preferentially adsorbed on the negatively charged clay surface compared to the sugars and carboxylate-rich aromatics and amino acids. With divalent metal cations, our model adsorbate conformations illustrate hydrated metal cation bridging of carboxylate-containing biomolecules to the clay surface, thus explaining divalent cation-promoted adsorption from our experimental data. Adsorption experiments with a mixture of biomolecules reveal selective inhibition in biomolecule adsorption, which our molecular modeling attributes to electrostatic biomolecule-biomolecule pairing that is more energetically favorable than the biomolecule-clay complex. In sum, our findings highlight chemical and structural features that can inform hypotheses for predicting biomolecule adsorption at water-clay interfaces.

Nanoscale Insights into the Interaction Mechanism Underlying the Adsorption and Retention of Heavy Metal Ions by Humic Acid

The mobility and distribution of heavy metal ions (HMs) in aquatic environments are significantly influenced by humic acid (HA), which is ubiquitous. A quantitative understanding of the interaction mechanism underlying the adsorption and retention of HMs by HA is of vital significance but remains elusive. Herein, the interaction mechanism between HA and different types of HMs (i.e., Cd(II), Pb(II), arsenate, and chromate) was quantitatively investigated at the nanoscale. Based on quartz crystal microbalance with dissipation tests, the adsorption capacities of Pb(II), Cd(II), As(V), and Cr(VI) ionic species on the HA surface were measured as ∼0.40, ∼0.25, ∼0.12, and ∼0.02 nmol cm-2, respectively. Atomic force microscopy force results showed that the presence of Pb(II)/Cd(II) cations suppressed the electrostatic double-layer repulsion during the approach of two HA surfaces and the adhesion energy during separation was considerably enhanced from ∼2.18 to ∼5.05/∼4.18 mJ m-2. Such strong adhesion stems from the synergistic metal-HA complexation and cation-π interaction, as evidenced by spectroscopic analysis and theoretical simulation. In contrast, As(V)/Cr(VI) oxo-anions could form only weak hydrogen bonds with HA, resulting in similar adhesion energies for HA-HA (∼2.18 mJ m-2) and HA-As(V)/Cr(VI)-HA systems (∼2.26/∼1.96 mJ m-2). This work provides nanoscale insights into quantitative HM-HA interactions, improving the understanding of HMs biogeochemical cycling.

Facet-Dependent Charge Density of Serpentine: Nanoscopic Implications for Aggregation and Entrainment of Fine Particles

Deciphering the facet-dependent surface properties of clay minerals holds vital significance in both fundamental research and practical engineering applications. To date, the anisotropic local charge density of serpentine surfaces still remains elusive, and thus, the interaction energies and associated aggregate structures between different crystal planes of serpentine cannot be quantitatively determined. In this work, different crystal planes of serpentine (i.e., SiO basal, MgOH basal, and edge) were selectively exposed, and their surface potentials and charge densities were determined using atomic force microscopy (AFM) force measurements coupled with Derjaguin-Landau-Verwey-Overbeek (DLVO) theory fitting. The SiO and edge planes consistently exhibited a permanently negative surface charge, whereas the point of zero charge (PZC) on the MgOH plane was estimated to be pH 9.0-11.0. Based on the interaction energy calculation between different serpentine planes, the aggregation structures of serpentine were predicted. Combined with scanning electron microscopy observation of freeze-dried samples, SiO-MgOH and MgOH-edge associations were found to dominate the aggregate structures at pH ≤ 9.0, thereby resulting in a stacking or "card-houses" structures. In contrast, all of the plane associations exhibited the repulsive interaction energy at pH 11.0, which led to a completely dispersed system, ultimately causing the most severe fine particle entrainment during froth flotation. Our work provides quantitative clarification of facet-dependent surface properties and aggregate structures of serpentine under different pH conditions, which will help improve the fundamental understanding of colloidal behaviors of clay minerals.

Understanding the Nanoscale Affinity between Dissolved Organic Matter and Noncrystalline Mineral with the Implication for Water Treatment

In recent decades, the concentration of dissolved organic matter (DOM) in aquatic ecosystems has gradually increased, leading to water pollution problems. Understanding the interfacial chemical processes of DOM on natural minerals is important to the exploration of high-efficiency absorbents. However, studying DOM chemical processes and adsorption mechanisms are still challenging due to the complex DOM structure and environmental system. Hence, we characterized the microstructure changes after the formation of amorphous calcium phosphate (ACP) at the interface of montmorillonite (Mt) minerals in a simulated environment system. Combined with atomic force microscopy and density functional theory (DFT) simulation, the mechanism of interfacial interaction between Mt-ACP and DOM was characterized at the molecular level. Moreover, we further evaluated the adsorption behavior of Mt-ACP as a potential adsorbent for organic matter. The comprehensive investigation of humic acid adsorption, intermolecular force, and DFT simulation is conducive to our understanding of the interfacial interaction mechanism between organic matter and noncrystalline minerals in aquatic environments and provides new perspectives on the application of clay-based mineral materials in pollutant removal under exposure from DOM.

Influence of microplastics on the transport of antibiotics in sand filtration investigated by AFM force spectroscopy

Microplastics and antibiotics were frequently detected in the effluent of sand filtration, while the presence of microplastics may change the interactions between the antibiotics and the quartz sands. However, the influence of microplastics on the transport of antibiotics in sand filtration has not been revealed. In this study, ciprofloxacin (CIP) and sulfamethoxazole (SMX) were respectively grafted on AFM probes to determine the adhesion forces to the representative microplastics (PS and PE) and the quartz sand. CIP and SMX exhibited low and high mobilities in the quartz sands, respectively. Compositional analysis of the adhesion forces indicated that the lower mobility of CIP in sand filtration columns could be attributed to the electrostatic attraction between the quartz sand and CIP compared with repulsion for SMX. Moreover, the significant hydrophobic interaction between the microplastics and the antibiotics could be responsible for the competitive adsorption of the antibiotics to the microplastics from the quartz sands; meanwhile, the π-π interaction further enhanced the adsorption of PS to the antibiotics. As a result of the high mobility of microplastics in the quartz sands, the carrying effect of microplastics enhanced the transport of antibiotics in the sand filtration columns regardless of their original mobilities. This study provided insights into the mechanism of the microplastics on enhancing the transport of antibiotics in sand filtration systems from the perspective of the molecular interaction.

Insights to Fe(II) on the fate of humic acid and humic acid Fe complex with biogeobattery effect in simultaneous partial nitritation, anammox and denitrification (SNAD) system

The role of Fe(II) on the humic acid (HA) transformation and the effects of humic acid Fe (HA-Fe) on simultaneous partial nitrification, anammox and denitrification (SNAD) system were investigated. After adding Fe(II), the HA content decreased and the HA inhibition on the SNAD system was released. Results showed that Fe(II) and HA formed the lower water-soluble HA-Fe, promoting the HA removal. HA-Fe with stronger electron transfer capacity constituted the interface with microorganisms to forming the biogeobattery effect. This accelerated the microbial electron transfer, as well as improved the key enzymes and ATP, indicating that HA-Fe stimulated the microbial activity of the SNAD system. Microbial community and quorum sensing analysis further demonstrated that HA-Fe enhanced the mutual symbiosis between electroactive and nitrogen removal bacteria, to ensure the stability of the SNAD system. The study provided references for efficient HA removal and revealed the biogeobattery effect of HA-Fe in the SNAD system.

Adsorption of typical natural organic matter on microplastics in aqueous solution: Kinetics, isotherm, influence factors and mechanism

With rapid urbanization, microplastics and natural organic matters (NOMs) are ubiquitous in aquatic environment, and microplastics could act as carriers for organic matters in the aqueous solution and may pose a potential risk. In this study, the adsorption behaviors and mechanism of typical NOM, humic acid (HA), on polyvinyl chloride (PVC) and polystyrene (PS) microplastics were investigated. Various influence factors such as solution pH, ions species and concentrations, particle size, and coexisting surfactants were studied. The results suggested that HA adsorption onto PVC and PS was low pH-dependent, and ion species and concentrations have a significant impact on the adsorption capacity. In addition, the particle size of PVC and PS microplastics exhibited a significant correlation with HA adsorption, and the adsorption process was influenced by the surfactant species and concentrations. Moreover, the adsorption behaviors of HA in different real water environments were tested, and UV aging exhibited the opposite effects on adsorption capacity of PVC and PS. Furthermore, the adsorption mechanisms of HA onto PVC and PS were explored, indicating halogen bonding, hydrogen bonding, and π-π interaction play important roles in the adsorption process.

Methine initiated polypropylene-based disposable face masks aging validated by micromechanical properties loss of atomic force microscopy

The contagious coronavirus disease-2019 pandemic has led to an increasing number of disposable face masks (DFMs) abandoned in the environment, when they are exposed to the air condition, the broken of chemical bond induced aging is inevitably occurred which meantime would cause a drastic decrease of the mechanical flexibility. However, the understanding of between chemical bond change related to aging and its micromechanical loss is limited due to the lack of refined techniques. Herein, the atomic force microscopy (AFM) technique was firstly used to observe the aging process induced by methine of the polypropylene-based DFMs. By comparing the micromechanical properties loss, the influences of humidity and light density on the DFM aging were systematically studied in the early 72 h, and it revealed that the increasing scissions number of the easiest attacked methine (C^t-H) can gradually decrease the micromechanical properties of the polypropylene (PP)-based DFM. Furthermore, the results are also validated by the in- situ FTIR and XPS analysis. This work discloses that an aging process can be initially estimated with the micromechanical changes observed by AFM, which offers fundamental data to manage this important emerging plastic pollution during COVID-19 pandemic.

Influence of Salts on the Photocatalytic Degradation of Formic Acid in Wastewater

Conventional wastewater treatment technologies have difficulties in feasibly removing persistent organics. The photocatalytic oxidation of these contaminants offers an economical and environmentally friendly solution. In this study, TiO₂ membranes and Ag/TiO₂ membranes were prepared and used for the decomposition of dissolved formic acid in wastewater. The photochemical deposition of silver on a TiO₂ membrane improved the decomposition rate. The rate doubled by depositing ca. 2.5 mg of Ag per 1 g of TiO₂. The influence of salinity on formic acid decomposition was studied. The presence of inorganic salts reduced the treatment performance of the TiO₂ membranes to half. Ag/TiO₂ membranes had a larger reduction of ca. 40%. The performance was recovered by washing the membranes with water. The anion adsorption on the membrane surface likely caused the performance reduction.

Impacts of Calcium Addition on Humic Acid Fouling and the Related Mechanism in Ultrafiltration Process for Water Treatment

Humic acid (HA) is a major natural organic pollutant widely coexisting with calcium ions (Ca²⁺) in natural water and wastewater bodies, and the coagulation-ultrafiltration process is the most typical solution for surface water treatment. However, little is known about the influences of Ca²⁺ on HA fouling in the ultrafiltration process. This study explored the roles of Ca²⁺ addition in HA fouling and the potential of Ca²⁺ addition for fouling mitigation in the coagulation-ultrafiltration process. It was found that the filtration flux of HA solution rose when Ca²⁺ concentration increased from 0 to 5.0 mM, corresponding to the reduction of the hydraulic filtration resistance. However, the proportion and contribution of each resistance component in the total hydraulic filtration resistance have different variation trends with Ca²⁺ concentration. An increase in Ca²⁺ addition (0 to 5.0 mM) weakened the role of internal blocking resistance (9.02% to 4.81%) and concentration polarization resistance (50.73% to 32.17%) in the total hydraulic resistance but enhanced membrane surface deposit resistance (33.93% to 44.32%). A series of characterizations and thermodynamic analyses consistently suggest that the enlarged particle size caused by the Ca²⁺ bridging effect was the main reason for the decreased filtration resistance of the HA solution. This work revealed the impacts of Ca²⁺ on HA fouling and demonstrated the feasibility to mitigate fouling by adding Ca²⁺ in the ultrafiltration process to treat HA pollutants.

Wetting-Induced Water Promoted Flow on Tunable Liquid-Liquid Interface-Based Nanopore Membrane System

Membrane separation provides effective methods for solving the global water crisis. Contemporary membrane systems depend on interfacial interactions between liquid and solid membrane matrixes. However, it may lead to a limiting permeate flux due to the large flow resistance at hydrophobic liquid-solid interfaces. Herein, the liquid-liquid interface with improved interface energy is reversibly introduced in membrane systems to boost wetting and reduce transport resistance. A series of interfaces were systematically explored to reveal mechanisms of wetting and boosted flow performances, which are further supported by simulations. Findings of this study highlight that interfacial liquids with lower surface energies, lower viscosities, and higher solubilities can effectively improve water flow without sacrificing rejection performance, achieving by transforming a solid-liquid interface into liquid-liquid interface interaction. It provides a concept to design advanced membrane systems for water purification (e.g., desalination and oil-water separation) and energy conversion processes.

Adsorption of Trisiloxane Surfactant for Selective Flotation of Scheelite from Calcite at Room Temperature

The separation and enrichment of scheelite from calcite are hindered by the similar active Ca²⁺ sites of scheelite and the calcite with calciferous gangue. Herein, a novel trisiloxane surfactant, N-(2-aminoethyl)-3-aminopropyltrisiloxane (AATS), was first explored and synthesized and recommended as the collector for the flotation separation of scheelite from calcite. The micro-flotation and mixed binary mineral flotation tests showed that AATS had excellent collection performance for scheelite and high selectivity for calcite within a wide pH range. At the same time, contact angle and zeta-potential measurements, Fourier transform infrared (FTIR) analysis, and density functional theory (DFT) calculations revealed the relevant adsorption mechanism. The contact angle measurement showed that AATS can increase the contact angle of the scheelite surface from 41.7 to 95.8°, greatly enhancing the hydrophobicity of the mineral surface. The results of FTIR analysis and zeta-potential measurement explained that AATS was electrostatically adsorbed on the mineral surface, and DFT calculation further verified that the -N⁺H₃-positive group in AATS was adsorbed on the negatively charged scheelite surface. Therefore, AATS can realize the expectation of high efficiency and selectivity of minerals and enhance the adhesion between the surface of scheelite minerals and bubbles, providing a fresh approach to industrial production.

NOM-mineral interaction: Significance for speciation of cations and anions

In this study, the nano-scale spatial distribution of natural organic matter (NOM) on the surface of iron (hydr)oxides and its relevance to oxyanion (PO₄^3-) and metal cation (Cd²⁺ and Cu²⁺) adsorption to the assemblage of oxide (goethite) and NOM (humic acids (HA) or fulvic acids (FA)) was investigated with experiments and advanced surface complexation modeling. Both the linear additive Multi-Surface model (MSM) and the more sophisticated Natural Organic Matter-Charge Distribution (NOM-CD) model were used. The MSM model ignores the effects of NOM-mineral interaction on ion adsorption, whereas the NOM-CD model considers this effect. The results showed that with the increase of NOM loading on oxides, deviation between the MSM and NOM-CD model became bigger for PO₄^3-, but smaller for Cd²⁺ and Cu²⁺. Oxyanions bind mainly to oxides and therefore the competitive effect of NOM cannot be neglected, which explains the large difference between these two models for PO₄^3-. On the contrary, at a relatively high NOM loading, a large fraction of NOM extends further away from the surface of oxides. Thus for metal cations that bind mainly to NOM, the influence of NOM-mineral interaction on their adsorption is small and the results of the MSM and NOM-CD model are similar. In top soils, the NOM loading on oxides is often high, therefore the linear additive MSM is applicable for metal cation speciation calculations as reported in many literatures. An approach based on the NOM-CD model was proposed, which can not only calculate the macroscopic solid-solution distribution of both cations and anions, but can also provide information regarding their microscopic surface speciation.

New insights into the cooperative adsorption behavior of Cr(VI) and humic acid in water by powdered activated carbon

Chromium and humic acid often co-exist in wastewater and source waters, and the removal of chromium through sorption by activated carbon may be greatly influenced by humic acid. In this study, we systematically evaluated concurrent adsorption of humic acid (HA) and hexavalent chromium (Cr(VI)) in water by powdered activated carbon (PAC) and further, the effect on conversion to trivalent chromium (Cr(III)). Adsorption of both HA and Cr(VI) was significantly enhanced in the dual adsorbate system as compared to treatments with HA or Cr(VI) alone. The removal of HA increased by 16.0% in the presence of 80 mg/L Cr(VI), while the removal of Cr(VI) similarly increased with increasing levels of HA. However, the promotion effect of HA was found to decrease with increasing pH. With HA at 20 mg/L, removal of Cr(VI) increased from 40.09% to 70.12% at pH 3, which was about twice the increase at pH 10. The cooperative adsorption mechanism was explored using scanning electron microscopy coupled with energy dispersive spectroscopy (SEM-EDS), Raman spectroscopy, Fourier transform infrared spectrometer (FTIR), and X-ray photoelectron spectroscopy (XPS). Comprehensive analysis of spectra suggested that the mutual promotion between HA and Cr(VI) adsorption was attributable to the formation of Cr(VI)-HA and Cr(III)-HA complexes that were readily adsorbed on the PAC surfaces. The higher HA concentrations increased the reduction of Cr(VI) to Cr(III), which was likely due to the electron transfer provided by the functional groups such as -CO, -OH and -COOH in both PAC and HA. At pH 3, 99.1% of Cr adsorbed on the PAC surface was in the form of Cr(III). These findings imply that the interactions between Cr(VI) and HA in the process of water treatment by PAC provides additional and synergistic benefits, leading to a greater removal of chromium.

Adsorption and interaction mechanisms of Chi-g-P(AM-DMDAAC) assisted settling of kaolinite in a two-step flocculation process

Flocculation has been widely employed in treatment of mineral tailings and water management. In this study, a chitosan-graft-poly(acrylamide-dimethyl diallyl ammonium chloride) (Chi-g-P(AM-DMDAAC)) was synthesized in-house. The adsorption and interaction mechanisms of Chi-g-P(AM-DMDAAC) and an anionic polyacrylamide (APAM) in a two-step flocculation process of kaolinite were explored using settlement tests, zeta potential measurement, quartz crystal micro-balance with dissipation (QCM-D) and atomic force microscopy (AFM) technique. The type of primary flocculant was critical for the two-step flocculation process. The treatment of the kaolinite suspension using 1 mg/L of Chi-g-P(AM-DMDAAC) followed by adding 2 mg/L of APAM displayed more efficient flocculation performance. QCM-D results showed that three dissipative layers were assembled on model kaolinite surface after sequentially injecting 3.5 mg/L of Chi-g-P(AM-DMDAAC), 0.05 wt% kaolinite suspension and 2.5 mg/L of APAM. The above total adsorption amount (Δf of -64.9 Hz) was much higher than that of using the two flocculants in reverse order (Δf of -23.1 Hz). This result indicated that the adsorption layer of the positively charged Chi-g-P(AM-DMDAAC) on kaolinite surface provided active adsorption sites for APAM. Further AFM measurement confirmed that the average adhesion between the silicon tip adsorbed Chi-g-P(AM-DMDAAC) and model kaolinite surface in 2.5 mg/L APAM solution increased from 0.25 ± 0.1 nN to 4.2 ± 0.3 nN with the effective interaction range of 700 nm, which was stronger than that measured between a bare silicon tip and silica substrate in single-component-flocculant solutions. The highly efficient two-step flocculation process could be ascribed to the strong electrostatic attraction between the kaolinite and the oppositely charged Chi-g-P(AM-DMDAAC) and APAM. Findings in this study will benefit the development of environmentally friendly flocculant for mineral tailings and water treatment.

Electrospun Cellulose-Acetate/Chitosan Fibers for Humic-Acid Removal: Improved Efficiency and Robustness with a Core-Sheath Design

Recycling biomass waste into functional materials has attracted much attention, and a rational structural design can make more effective use of each component. In our previous work, the fabrication of electrospun cellulose-acetate (CA)/chitosan (CS) adsorbents for humic-acid (HA) removal guided by the intermolecular interaction mechanism was demonstrated. Herein, a core-sheath structure was designed via one-step co-axial electrospinning, where a mixture of CS and CA was employed as the sheath layer to efficiently adsorb HA, and cellulose nanocrystals (CNCs) derived from waste cotton fabrics were incorporated into the CA core as load-bearing components. Compared to the non-layered electrospun CS/CA fibers, all the CS/CA–CNC fibers with a core-sheath structure exhibited smaller diameters, greater homogeneity, and significantly improved mechanical strength. Meanwhile, their maximum adsorption capacities towards HA had no significant differences. Even after the complete hydrolysis of CA into cellulose, the electrospun fibers maintained the fibrous structures and showed a higher tensile strength while exhibiting an acceptable adsorption capacity towards HA. Therefore, this work demonstrates the importance of rational design in the efficient preparation of functional materials and the feasibility of using electrospun core-sheath fibers derived from biomass wastes for the removal of water contaminants.

Deciphering effects of humic acid in landfill leachate on the simultaneous nitrification, anammox and denitrification (SNAD) system from performance, electron transfer and microbial community

Simultaneous nitrification, anammox and denitrification (SNAD) system is effective for landfill leachate treatment. However, humic acid (HA) as both an organic pollutant and electron shuttle in landfill leachate, its effects on the SNAD system remain unknown. This study demonstrated that HA initially inhibited NH₄⁺-N removal efficiency due to HA inhibition on anammox bacteria (the lowest fell to 90.89% from 100%), but the HA inhibition was released after adaption in the SNAD system. Hence, the mechanism of releasing HA inhibition in the SNAD system was established from performance, electron transfer and microbial community. Firstly, HA could be effectively removed by an adsorption-biodegradation process in the SNAD system, which avoided deteriorated performance caused by HA accumulation. Electrochemical analysis demonstrated that HA stimulated riboflavin and flavin mononucleotide (FMN) secretion to promote electron transfer efficiency. With the improved electron transfer efficiency, ETSA and ATP values significantly increased, indicating that HA enhanced the microbial metabolism activity of the SNAD system. Further analysis by enzymatic activity assay showed that the HAO (39.68 to 69.53 U/L), AMO (242.94 to 308.36 U/L), HZO (133.73 to 169.65 U/mL), NXR (24.63 to 54.52 U/L), NAR (94.40 to 114.36 U/L) and NIR (104.40 to 123.74 U/L) activities were improved with the HA increased from 0 to 200 mg/L, manifesting that HA enhanced nitrogen metabolism in the SNAD system. Besides, more reasonable metabolic division of labor in functional bacterial and enrichment of heterotrophic bacteria achieved efficient simultaneous removal of HA and nitrogen. Overall, efficient HA biodegradation, faster electron transfer efficiency and better metabolic division of microbial communities released HA inhibition, making the SNAD system more resistant to HA stress. This study shed light on the effects of HA on the SNAD system and provided a new insight for the SNAD system to landfill leachate treatment.

Adhesion force evolution of protein on the surfaces with varied hydration extent: Quantitative determination via atomic force microscopy

The adhesion force evolution of protein on surfaces with continuously varied hydrophobicity/hydration layer has not been completely clarified yet, limiting the further development of environmental applications such as membrane anti-biofouling and selective adsorption of the functional surfaces. Herein, chemical force spectroscopy using atomic force microscopy (AFM) was utilized to quantify the evolution of the adhesion forces of protein on hydration surfaces in water, where bovine serum albumin (BSA) was immobilized on an AFM tip as the representative protein. The stiffness, roughness and charge properties of the substrate surfaces were kept constant and the hydrophobicity was the only variant to monitor the role of hydrated water layers in protein adhesion. The adhesion force increased non-monotonically as a function of hydrophobicity of substrate surfaces, which was related to the concentration of humic acid, and independent of pH values and ionic strength. The non-monotonic variation occurred in the range of contact angle at 60-80° due to the mutual restriction between solid-liquid interface energy and solid-solid interface energy. Hydrophobic attraction was the dominant force that drove adhesion of BSA to these model substrate surfaces, but the passivation of hydration layers at the interface could weaken the hydrophobic attraction. In contrast to the measurements in water, the adhesion forces decreased as a function of surface hydrophobicity when measured in air, because capillary forces from condensation water dominated adhesion forces. The passivation of hydration layers of protein was revealed by quantitatively determining the evolution of adhesion forces on the hydration surfaces of varying hydrophobicity, which was ignored by traditional adhesion theory.

Optimum parameters for humic acid removal and power production by Al-air fuel cell electrocoagulation in synthetic wastewater

Although humic acid (HA) is a complex natural organic matter, it can potentially harm the environment and human health. In this study, aluminum-air fuel cell electrocoagulation (AAFCEC) was used to remove HAs from water while generating electricity. Initial pH, electrolyte concentration, HA concentration electrode distance and external resistance were investigated to determine the power generation and removal efficiency. The results showed that the better performance of power generation has been acquired in the alkaline solution and larger electrolyte concentration and short electrode distance. Further, Al-Ferron complexation timed spectrophotometry was used to determine the Al speciation distribution in the solution under different parameters. The power density of the cell reached 313.47 mW/cm² for the following conditions: 1 g/L NaCl concentration, 3 cm electrode distance, 20 Ω external resistor, and pH 9. After about an hour of electrolysis, the optimum removal rate of HA was above 99%. The results demonstrated that the AAFCEC is an efficient and eco-friendly water treatment process, and it could be further developed and disseminated in the rural areas and households.

Surface interaction mechanisms in mineral flotation: Fundamentals, measurements, and perspectives

As non-renewable natural resources, minerals are essential in a broad range of biological and technological applications. The surface interactions of mineral particles with other objects (e.g., solids, bubbles, reagents) in aqueous suspensions play a critical role in mediating many interfacial phenomena involved in mineral flotation. In this work, we have reviewed the fundamentals of surface forces and quantitative surface property-force relationship of minerals, and the advances in the quantitative measurements of interaction forces of mineral-mineral, bubble-mineral and mineral-reagent using nanomechanical tools such as surface forces apparatus (SFA) and atomic force microscope (AFM). The quantitative correlation between surface properties of minerals at the solid/water interface and their surface interaction mechanisms with other objects in complex aqueous media at the nanoscale has been established. The existing challenges in mineral flotation such as characterization of anisotropic crystal plane or heterogeneous surface, low recovery of fine particle flotation, and in-situ electrochemical characterization of collectorless flotation as well as the future work to resolve the challenges based on the understanding and modulation of surface forces of minerals have also been discussed. This review provides useful insights into the fundamental understanding of the intermolecular and surface interaction mechanisms involved in mineral processing, with implications for precisely modulating related interfacial interactions towards the development of highly efficient industrial processes and chemical additives.

Nanomechanical Insights into Versatile Polydopamine Wet Adhesive Interacting with Liquid-Infused and Solid Slippery Surfaces

Mussel-inspired polydopamine (PDA) can be readily deposited on almost all kinds of substrates and possesses versatile wet adhesion. Meanwhile, slippery surfaces have attracted much attention for their self-cleaning capabilities. It remains unclear how the versatile PDA adhesive would interact with slippery surfaces. In this work, both liquid-infused poly(tetrafluoroethylene) (PTFE) (LI-PTFE) and solid slippery surfaces (i.e., self-assembly of small thiol-terminated organosilane, polysiloxane covalently attached to substrates) were fabricated to investigate their capability to prevent PDA deposition. It was found that PDA particles could be easily deposited on a PTFE membrane and the two types of solid slippery surfaces, which resulted in the alternation of their surface wettability and slippery behavior of water droplets. Adhesion was detected between a PDA-coated silica colloidal probe and the PTFE membrane or solid slippery surfaces through quantitative force measurements using an atomic force microscope (AFM), mainly due to van der Waals (vdW) and hydrophobic interactions, which led to the PDA deposition phenomenon. In contrast, LI-PTFE with a thin liquid lubricant film could effectively prevent PDA deposition, with negligible changes in surface morphology, wettability, and slippery characteristics. Although PDA particles could be loosely attached to the lubricant/water interface for LI-PTFE based on the capillary adhesion measured by AFM, they could be readily removed by gentle rinsing with water, as demonstrated by the ultralow friction over LI-PTFE as compared to PTFE using lateral force microscopy (LFM). Our results indicate that LI-PTFE possesses excellent antifouling and self-cleaning properties even when interacting with the versatile PDA wet adhesives. This work provides new insights into the deposition of PDA on slippery surfaces and their interaction mechanism at the nanoscale, with useful implications for the design and development of novel slippery surfaces.

A Nanomechanical Study on Deciphering the Stickiness of SARS-CoV-2 on Inanimate Surfaces

The SARS-CoV-2 virus that causes the COVID-19 epidemic can be transmitted via respiratory droplet-contaminated surfaces or fomites, which urgently requires a fundamental understanding of intermolecular interactions of the coronavirus with various surfaces. The corona-like component of the outer surface of the SARS-CoV-2 virion, named spike protein, is a key target for the adsorption and persistence of SARS-CoV-2 on various surfaces. However, a lack of knowledge in intermolecular interactions between spike protein and different substrate surfaces has resulted in ineffective preventive measures and inaccurate information. Herein, we quantified the surface interaction and adhesion energy of SARS-CoV-2 spike protein with a series of inanimate surfaces via atomic force microscopy under a simulated respiratory droplet environment. Among four target surfaces, polystyrene was found to exhibit the strongest adhesion, followed by stainless steel (SS), gold, and glass. The environmental factors (e.g., pH and temperature) played a role in mediating the spike protein binding. According to systematic quantification on a series of inanimate surfaces, the adhesion energy of spike protein was found to be (i) 0-1 mJ/m2 for hydrophilic inorganics (e.g., silica and glass) due to the lack of hydrogen bonding, (ii) 2-9 mJ/m2 for metals (e.g., alumina, SS, and copper) due to the variation of their binding capacity, and (iii) 6-11 mJ/m2 for hydrophobic polymers (e.g., medical masks, safety glass, and nitrile gloves) due to stronger hydrophobic interactions. The quantitative analysis of the nanomechanics of spike proteins will enable a protein-surface model database for SARS-CoV-2 to help generate effective preventive strategies to tackle the epidemic.

Probing the Interaction Mechanism between Benzohydroxamic Acid and Mineral Surface in the Presence of Pb2+ Ions by AFM Force Measurements and First-Principles Calculations

Probing the interaction mechanism between organic molecules and material surfaces in the presence of metal ions is of great importance in many fields, such as mineral flotation. The collectability of benzohydroxamic acid (BHA) to a spodumene (LiAl(SiO₃)₂) mineral surface during mineral flotation could be enhanced with the addition of metal ion activators-Pb²⁺ ions. Pb²⁺ ions could be added as either Pb-BHA complex formed by premixing Pb²⁺ ions and BHA molecules at a given ratio or sequential addition of Pb²⁺ ions and BHA molecules. However, the complete understanding of the interaction mechanisms (e.g., adhesion) between BHA and the spodumene mineral surface in the presence of Pb²⁺ ions remains very limited. In this study, atomic force microscopy (AFM) was used to measure the intermolecular forces between BHA and the spodumene mineral surface in aqueous solutions. A BHA model molecule, that is, N-hydroxy-4-mercaptobenzamide (MBHA), was synthesized to prepare a BHA-functionalized AFM probe for force measurements. Two model systems (i.e., a Pb-BHA complex interacting with the spodumene mineral surface (model I) and BHA with a Pb²⁺-activated spodumene surface (model II)) were investigated for comparing the role of Pb²⁺ in BHA-mineral adhesion. The adhesion measured for model I (23.7 mN/m) is much higher than that of model II (12.5 mN/m), as further supported by the adsorption energies obtained from density functional theory (DFT) calculations. The calculation results showed a higher adsorption energy for model I (∼188.58 kJ/mol) than model II (∼128.16 kJ/mol), which is due to the better spodumene flotation recovery for the Pb-BHA complex as a collector than the sequential addition of Pb²⁺ and BHA. This work provides useful information on the intermolecular interactions between chemical additives and mineral surfaces in complex mineral flotation processes, and the methodology can be readily extended to other related interfacial processes such as membrane technology, water treatment, oil production, and bioengineering processes.