Bisphenol A Electrochemical Sensor Using Graphene Oxide and β-Cyclodextrin-Functionalized Multi-Walled Carbon Nanotubes

Sensitive and selective detection of heavy metal ions and organic pollutants with graphene-integrated sensing platforms

Graphene-based sensors have emerged as promising tools for environmental monitoring due to their exceptional properties such as high surface area, excellent electrical conductivity, and sensitivity to various analytes. This paper presents a review of recent advancements in the development and application of graphene-based sensors for the detection of heavy metal ions and organic pollutants. These sensors employ either graphene or its derivatives, often in combination with graphene hybrid nanocomposites, as the primary sensing material. The synthesis methods of graphene and sensing mechanisms of graphene-based sensors are discussed. Furthermore, performance metrics including the determination range and detection limits of these sensors are itemized. The potential challenges and future directions in the field of graphene-based sensors for environmental monitoring are also highlighted. Overall, this review provides valuable insights into the current state-of-the-art technologies and paves the way for the development of highly efficient and reliable sensors for environmental monitoring purposes.

Disposable electrochemical sensor: Highly sensitive determination of nitrofurazone antibiotic in environmental samples and pharmaceutical formulations

The study presents the successful development of a new electrochemical sensor with low cost and disposability for application in nitrofurazone detection in environmental and pharmaceutical samples. The sensors were fabricated using materials obtained from local storage and conductive carbon ink. The modification of the screen-printed electrodes with the hybrid nanomaterial based on silver nanoparticles, carbon quantum dots, and carbon nanotubes showed synergistic contributions in the nitrofurazone electrooxidation, as observed in the wide linear range (0.008 at 15.051 μM), with a sensitivity of 0.650 μA/μM. The limit of detection obtained was 4.6 nM. Differential pulse voltammetry, cyclic voltammetry, X-ray photoelectron spectroscopy, X-ray diffraction analysis, and high-resolution transmission electron microscopy were used to evaluate the electrochemical and structural characteristics. Studies of possible interferences were considered with nitrofurazone in the presence of the ions and organic molecules. The results were satisfactory, with a variation of 93.3% ± 4.39% at 100% ± 2.40%. The low volume used in the analyses (50 μL), disposability, high sensibility, selectivity, and low limit of detection are advantages that make the proposed sensor an electrochemical tool of high viability for the NFZ detection in environmental matrices and pharmaceutical formulations.

Development of ternary hybrid composites of transition metal and noble metal-based heterostructures: Ultrasensitive simultaneous electrochemical detection of bisphenol A and bisphenol S in food samples

Bisphenols threaten human health and sensitive detection is crucial. The present study aims to develop ternary composites of copper metal-organic framework (Cu-MOF) with AuAg microstructures. The composite structure was formed by a galvanic displacement reaction and confirmed using SEM. A binder-free catalyst was used to study the electrochemical redox reaction of bisphenol A (BPA) and bisphenol S (BPS); an irreversible cyclic voltammetric signal at +0.70 V and + 0.91 V (vs. Ag/AgCl), in the dynamic range of 20 nM to 2.0 mM, and 10 nM to 1.0 mM, with limits of detection of 2.9 nM, and 3.2 nM (S/N = 3) was obtained. Practical analysis was applied to frozen tomatoes, tuna fish, milk powder, PET bottles, raw milk, and urine samples with a recovery rate of 94.00-100.80% (n = 3). Voltammetric results were validated using HPLC detection with high precision. The sensor is a promising alternative platform for measuring BPA in food samples.

Sandwich-like voltametric immunosensing of interleukin-8 based on β-cyclodextrin/carbon nanotubes and methylthionine chloride@UIO-66 framework

The level of interleukin-8 (IL-8) in the body is an effective factor for the early diagnosis of acute tubular necrosis and oral tumor. In this work, a novel sandwich-like voltametric immunosensor (SVS) of IL-8 was constructed by preparing β-cyclodextrin/carbon nanotube (CD/CNT) to immobilize primary antibody (PAb) of IL-8 and UIO-66-NH2 MOFs structure to immobilize second antibody (SAb) and methylene blue (Mb) probe. In this designed SVS, the prepared CD/CNT nanohybrid with large surface area and conductivity can immobilize PAb via simple host-guest recognition, and UIO-66-NH2 provided an ideal platform to accommodate SAb and a large number of Mb molecules as signal-amplifier. In the existence of target IL-8, the current peak of Mb from the SVS assay increases with the increasement of IL-8 level. Through optimizing and adjusting various factors, a wide linearity (0.001-2.5 ng mL-1) and low analytical limit (0.2 pg mL-1) of IL-8 were realized, so it's expected the developed SVS strategy has significant applications for the detection of IL-8.

Simple and sensitive electrochemical sensing of amethopterin by using carbon nanobowl/cyclodextrin electrode

Resulted from the severe side effects, the development of inexpensive, simple and sensitive method for amethopterin (ATP, an antineoplastic drug) is very important but it still remains a challenge. In this work, low cost nanohybrid composed of carbon nanobowl (CNB) and β-cyclodextrins (β-CD) (CNB-CD) was prepared with a simple autopolymerization way and applied as electrode material to develop a novel electrochemical sensor of ATP. Scanning-/transmission-electron microscopy, Fourier transform infrared spectrum, photographic image and electrochemical technologies were utilized to characterize morphologies and structure of the as-prepared CNB and CNB-CD materials. On the basic of the coordination advantages from CNB (prominent electrical property and surface area) and β-CD (superior molecule-recognition and solubility capabilities), the CNB-CD nanohybrid modified electrode exhibits superior sensing performances toward ATP, and a low detection limit of 0.002 μM coupled with larger linearity of 0.005-12.0 μM are obtained. In addition, the as-prepared sensor offers desirable repeatability, stability, selectivity and practical application property, confirming that this proposal may have important applications in the determination of ATP.

Self-powered molecularly imprinted photoelectrochemical sensor based on Ppy/QD/HOF heterojunction for the detection of bisphenol A

As an emerging porous material, hydrogen-bonded organic framework materials (HOFs) still pose application challenges. In this work, the designed type "I + II" heterojunction extracted hot electrons from HOFs using quantum dots (QDs) and polypyrrole (Ppy), improving the stability and photoelectrochemical performance of materials. In addition to serving as a potential well, electropolymerized Ppy was used as a recognition element for bisphenol A (BPA), and a novel self-powered molecularly imprinted photoelectrochemical (MIP-PEC) sensor was designed. The sensing platform showed a linear relationship from 1 × 10-10 to 1 × 10-7 mol∙L-1 and from 1 × 10-7 to 1 mol∙L-1 with an acceptable detection limit of 4.2 × 10-11 mol∙L-1. This is the first application of HOFs in constructing MIP-PEC sensors and a new attempt to improve the stability of HOFs for the application of porous crystal materials in the sensing field.

An iron metal-organic framework-based electrochemical sensor for identification of Bisphenol-A in groundwater samples

Bisphenol A (BPA) is an endocrine disruptor that leaches into food and is significantly employed in food and beverage storage, and source water cycles. To ensure an outstanding and sustainable biosphere while safeguarding human health and well-being, BPA detection is essential, necessitating an efficient detection methodology. Here, we describe an easy-to-use, inexpensive, and overly sensitive electrochemical detector that uses Fe-MOF nanotextures for identifying BPA in groundwater. This sensing electrode device combines the excellent guest interaction potential of organic ligands with the substantial surface area of metal. Using various analytical techniques including scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FT-IR), and powder X-ray diffraction (XRD), the structural and physicochemical behaviors of the as-synthesized material were evaluated. Electrochemical BPA detection was enabled by a diffusion-controlled oxidation procedure with a comparable number of both protons and electrons. With a 0.1 μM detection limit, the sensor displayed a linear sensitivity of around 0.1 μM and 15 μM. Additionally, the sensors demonstrated an outstanding recovery with actual water samples as well as a repeatable and steady performance over the course of a month exhibiting minimal interference from typical inorganic and organic species. Due to its notable sensitivity, inexpensive cost, robust selectivity, excellent repeatability, and reuse ability, the electroanalytical possibilities of the Fe-MOF-modified GCE suggest that the device can be implemented into real-world applications in its primed condition.

Electrochemical sensing mechanisms of neonicotinoid pesticides and recent progress in utilizing functional materials for electrochemical detection platforms

The excessive residue of neonicotinoid pesticides in the environment and food poses a severe threat to human health, necessitating the urgent development of a sensitive and efficient method for detecting trace amounts of these pesticides. Electrochemical sensors, characterized by their simplicity of operation, rapid response, low cost, strong selectivity, and high feasibility, have garnered significant attention for their immense potential in swiftly detecting trace target molecules. The detection capability of electrochemical sensors primarily relies on the catalytic activity of electrode materials towards the target analyte, efficient loading of biomolecular functionalities, and the effective conversion of interactions between the target analyte and its receptor into electrical signals. Electrode materials with superior performance play a crucial role in enhancing the detection capability of electrochemical sensors. With the continuous advancement of nanotechnology, particularly the widespread application of novel functional materials, there is paramount significance in broadening the applicability and expanding the detection range of pesticide sensors. This comprehensive review encapsulates the electrochemical detection mechanisms of neonicotinoid pesticides, providing detailed insights into the outstanding roles, advantages, and limitations of functional materials such as carbon-based materials, metal-organic framework materials, supramolecular materials, metal-based nanomaterials, as well as molecular imprinted materials, antibodies/antigens, and aptamers as molecular recognition elements in the construction of electrochemical sensors for neonicotinoid pesticides. Furthermore, prospects and challenges facing various electrochemical sensors based on functional materials for neonicotinoid pesticides are discussed, providing valuable insights for the future development and application of biosensors for simplified on-site detection of agricultural residues.

Highly Sensitive Detection of Hydrogen Peroxide in Cancer Tissue Based on 3D Reduced Graphene Oxide-MXene-Multi-Walled Carbon Nanotubes Electrode

Hydrogen peroxide (H2O2) is a signaling molecule that has the capacity to control a variety of biological processes in organisms. Cancer cells release more H2O2 during abnormal tumor growth. There has been a considerable amount of interest in utilizing H2O2 as a biomarker for the diagnosis of cancer tissue. In this study, an electrochemical sensor for H2O2 was constructed based on 3D reduced graphene oxide (rGO), MXene (Ti3C2), and multi-walled carbon nanotubes (MWCNTs) composite. Three-dimensional (3D) rGO-Ti3C2-MWCNTs sensor showed good linearity for H2O2 in the ranges of 1-60 μM and 60 μM-9.77 mM at a working potential of -0.25 V, with sensitivities of 235.2 µA mM-1 cm-2 and 103.8 µA mM-1 cm-2, respectively, and a detection limit of 0.3 µM (S/N = 3). The sensor exhibited long-term stability, good repeatability, and outstanding immunity to interference. In addition, the modified electrode was employed to detect real-time H2O2 release from cancer cells and cancer tissue ex vivo.

One-step growth of Cu-doped carbon dots in amino-modified carbon nanotube-modified electrodes for sensitive electrochemical detection of BPA

Copper-doped carbon dots and aminated carbon nanotubes (Cu-CDs/NH2-CNTs) nanocomposites were synthesized by a one-step growth method, and the composites were characterized for their performance. An electrochemical sensor for sensitive detection of bisphenol A (BPA) was developed for using Cu-CDs/NH2-CNTs nanocomposites modified with glassy carbon electrodes (GCE). The sensor exhibited an excellent electrochemical response to BPA in 0.2 M PBS (pH 7.0) under optimally selected conditions. The linear range of the sensor for BPA detection was 0.5-160 μM, and the detection limit (S/N = 3) was 0.13 μM. Moreover, the sensor has good interference immunity, stability and reproducibility. In addition, the feasibility of the practical application of the sensor was demonstrated by the detection of BPA in bottled drinking water and Liu Yang River water.

Electrochemical Nanosensor for the Simultaneous Determination of Anticancer Drugs Epirubicin and Topotecan Using UiO-66-NH2/GO Nanocomposite Modified Electrode

In this work, UiO-66-NH2/GO nanocomposite was prepared using a simple solvothermal technique, and its structure and morphology were characterized using field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). An enhanced electrochemical sensor for the detection of epirubicin (EP) was proposed, which utilized a UiO-66-NH2/GO nanocomposite-modified screen-printed graphite electrode (UiO-66-NH2/GO/SPGE). The prepared UiO-66-NH2/GO nanocomposite improved the electrochemical performance of the SPGE towards the redox reaction of EP. Under optimized experimental conditions, this sensor demonstrates a remarkable limit of detection (LOD) of 0.003 µM and a linear dynamic range from 0.008 to 200.0 µM, providing a highly capable platform for sensing EP. Furthermore, the simultaneous electro-catalytic oxidation of EP and topotecan (TP) was investigated at the UiO-66-NH2/GO/SPGE surface utilizing differential pulse voltammetry (DPV). DPV measurements revealed the presence of two distinct oxidation peaks of EP and TP, with a peak potential separation of 200 mV. Finally, the UiO-66-NH2/GO/SPGE sensor was successfully utilized for the quantitative analysis of EP and TP in pharmaceutical injection, yielding highly satisfactory results.

Electrochemical Detection of Bisphenol A Based on Gold Nanoparticles/Multi-Walled Carbon Nanotubes: Applications on Glassy Carbon and Screen Printed Electrodes

Bisphenol A (BPA) has been classified as an endocrine-disrupting substance that may cause adverse effects on human health and the environment. The development of simple and sensitive electrochemical biosensors is crucial for the rapid and effective quantitative determination of BPA. This work presents a study on electrochemical sensors utilizing gold nanoparticle-modified multi-walled carbon nanotubes (CNT/AuNPs). Glassy carbon electrodes (GCEs) and screen-printed electrodes (SPEs) were conveniently modified and used for BPA detection. AuNPs were electrodeposited onto the CNT-modified electrodes using the galvanostatic method. The electrodes were properly modified and characterized by using Raman spectroscopy, cyclic voltammetry (CV), and electrochemical impedance analysis (EIS). The electrochemical response of the sensors was studied using differential pulse voltammetry (DPV) and constant potential amperometry (CPA) for modified GCE and SPE electrodes, respectively, and the main analytical parameters were studied and optimized. Problems encountered with the use of GCEs, such as sensor degradation and high limit of detection (LOD), were overcome by using modified SPEs and a flow injection device for the measurements. Under this approach, an LOD as low as 5 nM (S/N = 3) was achieved and presented a linear range up to 20 μM. Finally, our investigation addressed interference, reproducibility, and reusability aspects, successfully identifying BPA in both spiked and authentic samples, including commercial and tap waters. These findings underscore the practical applicability of our method for accurate BPA detection in real-world scenarios. Notably, the integration of SPEs and a flow injection device facilitated simplified automation, offering an exceptionally efficient and reliable solution for precise BPA detection in water analysis laboratories.

Simple and sensitive sandwich-like electrochemical immunosensing strategy for D-dimer based on cyclodextrin-carbon nanotube and nanogold-ferrocene

D-dimer is a very important biomarker about sepsis, pulmonary thromboembolism and atherosclerosis, thus designing effective and sensitive method for its detection is of great significance. Herein, by synthesizing β-cyclodextrin-carbon nanotube nanohybrid (CNTs-CD) as the carrier to assemble the initial antibody (Ab1) of D-dimer, immobilizing secondary antibody (Ab2) and sulfydryl ferrocene (Fc) on the nanogold (Au) particles surface as the signaling amplifier (Ab2-Au-Fc), a low cost, simple, sensitive and effective sandwich-like electrochemical immunosensing (SEI) platform of D-dimer was proposed in this work for the first time. Briefly, CNTs shows large specific area and superior electroconductivity, and CD provides high host guest recognition ability that could bound with Ab1; meanwhile, the Fc probe offers stable current response which are proportionable positively to the level of D-dimer. Under the best conditions, the designed SEI platform exhibits prominent analytical performances for D-dimer: low detection limit of 3.0 ng mL-1 and large linearity of 10.0-800.0 ng mL-1. In addition, the selectivity, stability and reproducibility as well as real applications of the proposed SEI assay were evaluated and the obtained results are satisfactory.

Single-Mg-Atom Catalyst with a Dual Active Center as an Emerging Promising Sensing Platform

Bisphenol compounds [bisphenol A (BPA), etc.] are one class of the most important and widespread pollutants in food and environment, which pose severe endocrine disrupting effect, reproductive toxicity, immunotoxicity, and metabolic toxicity on humans and animals. Simultaneous rapid determination of BPA and its analogues (bisphenol S, bisphenol AF, etc.) with extraordinary potential resolution and sensitivity is of great significance but still extremely challenging. Herein, a series of single-atom catalysts (SACs) were synthesized by anchoring different metal atoms (Mg, Co, Ni, and Cu) on N-doped carbon materials and used as sensing materials for simultaneous detection of bisphenols with similar chemical structures. The Mg-based SAC enables the potential discrimination and simultaneous rapid detection of multiple bisphenols, showing outstanding analytical performances, outperforming all other SACs and traditional electrode materials. Our experiments and density functional theory calculations show that pyrrolic N serves as the adsorption site for the adsorption of bisphenols and the Mg atom serves as the active site for the electrocatalytic oxidation of bisphenols, which play a synergistic role as dual active centers in improving the sensing performance. The results of this work may pave the way for the rational design of SACs as advanced sensing and catalytic materials.

Simple and sensitive sandwich-like voltammetric immunosensing of procalcitonin

Procalcitonin (PCT) is a reliable biomarker in the early diagnosis of septicemia, pyemia and stroke-associated pneumonia. In this work, through preparing β-cyclodextrin/graphene (CD/GN) nanohybrid as carrier and amplifier simultaneously to band antibodies and probe molecules, a simple and innovative sandwich-like voltammetric immunosensor was proposed for the sensitive and effective determination of PCT. Owing to the host-guest recognition property, the antibodies of PCT can enter into the CD cavities to generate a stable complex; meanwhile, aminopyrene (AP) were introduced as the signal probe and it was adsorbed on the surface of GN via aminopyrine π-πinteraction. Based on the signal change from AP as a response signal which exhibits linearity to the concentration of PCT, a highly sensitive sandwich-type voltammetric immunosensor was developed successfully after optimizing various key parameters. The results demonstrated that the developed sensor had a considerably low detection limit (0.003 pg mL-1) and wide linearity of 0.01 pg mL-1 to 20.0 ng mL-1. This work offered a very simple and sensitive sensing strategy for PCT and other biomarkers via altering the specific antibodies simply, showing great potential applications.

Design and synthesis of hierarchical MnO-Fe3O4@C/expanded graphite composite for sensitive electrochemical detection of bisphenol A

Hierarchically nanostructured binary transition metal oxide-based materials with high conductivity and catalytic activity are quite attractive for the electrochemical quantitative detection of environmental pollutants due to their natural abundance, variable oxidation state, and excellent synergies between metal sites. Herein, a new hierarchical MnO-Fe3O4@C/expanded graphite (EG) composite is designed and synthesized through a simple and in situ annealing method with the utilization of bimetallic organic framework (FeMn-MOF)/EG precursor. The synthesized MnO-Fe3O4@C/EG composite possesses a unique hierarchical nanoarchitecture that small-sized bimetallic oxide nanoparticles of 10-40 nm completely encapsulated by amorphous carbon layers of 2-4 nm are uniformly distributed on the EG platform. This distinctive structure combines the advantages of high conductivity, excellent catalytic activity, and strong stability. Resultantly, when it is applied to monitor environmental endocrine disruptors, the sensor exhibits a significant catalytic effect on the electrochemical oxidation of bisphenol A (BPA), inducing an amplified response current. In addition, the sensor shows a wide linear range of 1-50 μM and 50-400 μM for the BPA monitor, giving a sensitivity of 5208.8 and 1641.9 μA mM-1 cm-2, respectively. This study offers a new approach to design hierarchical binary metal oxide-based sensing materials as well as to explore their electrochemical properties and applications for the determination of emerging contaminants.

Sensitive Electrochemical Detection of Carcinoembryonic Antigen Based on Biofunctionalized Nanochannel Modified Carbonaceous Electrode

The convenient construction of carbon-based electrochemical immunosensors with high performance is highly desirable for the efficient detection of tumor biomarkers. In this work, an electrochemical immunosensor was fabricated by integrating a biofunctionalized mesoporous silica nanochannel film with a carbon-based electrode, which can enable the sensitive determination of carcinoembryonic antigen (CEA) in serum. The commonly used carbonaceous electrode, glassy carbon electrode (GCE), was employed as the supporting electrode and was pre-treated through electrochemical polarization to achieve the stable binding of a vertically ordered mesoporous silica film with amino groups (NH2-VMSF) without the use of any adhesive layer. To fabricate the immunorecognition interface, antibodies were covalently immobilized after the amino groups on the outer surface of NH2-VMSF was derivatized to aldehyde groups. The presence of amino sites within the high-density nanochannels of NH2-VMSF can facilitate the migration of negatively charged redox probes (Fe(CN)63-/4-) to the supporting electrode through electrostatic adsorption, leading to the generation of electrochemical signals. In the presence of CEA, the formation of immunocomplexes on the recognitive interface can reduce the electrochemical signal of Fe(CN)63-/4- on the supporting electrode. Based on this principle, the sensitive electrochemical detection of CEA was achieved. CEA can be determined to range from 0.01 ng mL-1 to 100 ng mL-1 with a limit of detection of 6.3 pg mL-1. The fabricated immunosensor exhibited high selectivity, and the detection of CEA in fetal bovine serum was achieved.

Sensors for Emerging Water Contaminants: Overcoming Roadblocks to Innovation

Ensuring water quality and safety requires the effective detection of emerging contaminants, which present significant risks to both human health and the environment. Field deployable low-cost sensors provide solutions to detect contaminants at their source and enable large-scale water quality monitoring and management. Unfortunately, the availability and utilization of such sensors remain limited. This Perspective examines current sensing technologies for detecting emerging contaminants and analyzes critical barriers, such as high costs, lack of reliability, difficulties in implementation in real-world settings, and lack of stakeholder involvement in sensor design. These technical and nontechnical barriers severely hinder progression from proof-of-concepts and negatively impact user experience factors such as ease-of-use and actionability using sensing data, ultimately affecting successful translation and widespread adoption of these technologies. We provide examples of specific sensing systems and explore key strategies to address the remaining scientific challenges that must be overcome to translate these technologies into the field such as improving sensitivity, selectivity, robustness, and performance in real-world water environments. Other critical aspects such as tailoring research to meet end-users' requirements, integrating cost considerations and consumer needs into the early prototype design, establishing standardized evaluation and validation protocols, fostering academia-industry collaborations, maximizing data value by establishing data sharing initiatives, and promoting workforce development are also discussed. The Perspective describes a set of guidelines for the development, translation, and implementation of water quality sensors to swiftly and accurately detect, analyze, track, and manage contamination.

Integration of Ultrathin Bubble Walls and Electrochemistry: Innovation in Microsensing for Forensic Nitrite Detection and Microscale Metallic Film Deposition

We present a strategy for electrochemical measurements using a durable minute bubble wall with a thickness of 27 μm (D = 1.8 cm) as an innovative electrochemical medium. The composition, thickness, and volume of the tiny bubble film were investigated and estimated using the spectroscopic method and the Beer-Lambert law. A carbon microelectrode (D = 10 μm) was then employed as the working electrode, inserted through the bubble wall to function as the solution interface. First, the potential of this method for microelectrodeposition of metallic Ag and Pd films in a tiny bubble was investigated. Interestingly, microscopic images of the deposited film clearly demonstrated that the bubble thickness determines and confines the electrochemical deposition zone. In other words, innovative template-free microelectrodeposition was achieved. In the second phase of our work, microelectroanalysis of trace levels of nitrite ions was performed within the bubble wall and on a foam-covered hand, between the fingers directly, with a low limit of detection of 28 μM. This technique holds significance in criminal investigations, as the presence of NO2- ions on the hand indicates the potential presence of gunshot residue and aids in identifying suspects. In comparison to current methods, this approach is rapid, simple, cost-effective, and amenable to on-site applications, eliminating the need for sample treatment. Ultimately, the utilization of a bubble wall as a novel electrochemical microreactor can open new ways in microelectrochemical analysis, presenting novel opportunities and applications in the field of electrochemical sensors.

Citric acid cross-linked β-cyclodextrins: A review of preparation and environmental/biomedical application

The β-cyclodextrins (β-CD) are biocompatible macrocyclic candidates for the preparation of various composites with enhanced functions. While nontoxic and biodegradable citric acid (CA) is the favorite crosslinking agent for fabricating hierarchical advanced structures. The carboxyl and hydroxyl groups on CA can serve as "structural bridges" and enhance the solubility of β-CD. Leading to the construction of CA cross-linked β-CD with marvelous complicated structures and targeted functions. Here, we directly categorized the grafted composite materials into two main types such as organic and inorganic materials. Particularly, some representative composite materials are listed and analyzed in detail according to their preparation, advantages of unique characteristics, as well as the possible applications in environmental and biomedical fields such as adsorption of pollutants, sensors, and biomedical applications.

Preparation of Gold Nanoparticles via Anodic Stripping of Copper Underpotential Deposition in Bulk Gold Electrodeposition for High-Performance Electrochemical Sensing of Bisphenol A

Bisphenol A is one of the most widely used industrial compounds. Over the years, it has raised severe concern as a potential hazard to the human endocrine system and the environment. Developing robust and easy-to-use sensors for bisphenol A is important in various areas, such as controlling and monitoring water purification and sewage water systems, food safety monitoring, etc. Here, we report an electrochemical method to fabricate a bisphenol A (BPA) sensor based on a modified Au nanoparticles/multiwalled carbon nanotubes composite electrocatalyst electrode (AuCu-UPD/MWCNTs/GCE). Firstly, the Au-Cu alloy was prepared via a convenient and controllable Cu underpotential/bulk Au co-electrodeposition on a multiwalled modified carbon nanotubes glassy carbon electrode (GCE). Then, the AuCu-UPD/MWCNTs/GCE was obtained via the electrochemical anodic stripping of Cu underpotential deposition (UPD). Our novel prepared sensor enables the high-electrocatalytic and high-performance sensing of BPA. Under optimal conditions, the modified electrode showed a two-segment linear response from 0.01 to 1 µM and 1 to 20 µM with a limit of detection (LOD) of 2.43 nM based on differential pulse voltammetry (DPV). Determination of BPA in real water samples using AuCu-UPD/MWCNTs/GCE yielded satisfactory results. The proposed electrochemical sensor is promising for the development of a simple, low-cost water quality monitoring system for the detection of BPA in ambient water samples.

Development of a novel green catalyzed nanostructured Cu(II) macrocyclic complex-based disposable electrochemical sensor for sensitive detection of bisphenol A in environmental samples

BPA is an endocrine disruptor and the leading environmental pollutant due to its use as raw material in industries. Therefore, the present work reports the sensitive, efficient, and disposable electrochemical paper-based SPE for determining the BPA sensor using an amide-based macrocyclic complex (nanostructured complex of copper acetate with macrocyclic ligand, i.e., CuL (CH3COO)2) synthesized using Citrus limon (lemon) extract via sonication for the first time. The structural, morphological, and electrochemical analyses have been characterized by mass spectroscopy, FTIR, UV-Vis, XRD, FESEM-EDX, elemental mapping and electrochemical techniques. The sensor platform for detecting BPA was fabricated by simple drop-casting on the disposable paper-based SPE using macrocyclic complex, i.e., CuL (CH3COO)2/SPE. After optimizing the conditions, CuL (CH3COO)2/SPE electrode was employed for determining BPA via CV with a wide linear range of 31 × 10-9 μM-0.205 μM, low LOD of 0.027 nM, and high sensitivity of 49.71 μA (log nM)-1 cm-2 having correlation coefficient (R2) of 0.976 which is quite better in compared to other reported SPE sensor for detection of BPA. Further, our sensor also showed good selectivity and reproducibility, in addition to detecting BPA in environmental samples (tube well water, river water and drain water) with acceptable recoveries and RSDs values. In this work, the combination of macrocyclic complex and paper-based SPE has turned out to be a cost-effective electrochemical sensor.

Electrochemical sensor for sensitive detection of bisphenol A based on molecularly imprinted TiO2 with oxygen vacancy

Bisphenol A (BPA) is an endocrine disrupting chemical and broadly used in plastics. The leakage of BPA in food and water cycles poses a significant risk to the environment and human health. Thus, monitoring the concentration of BPA to avoid its potential risk is highly important. In this work, a simple and efficient oxygen deficient molecularly imprinted TiO2 electrochemical sensor was proposed for the detection of BPA. The introduction both oxygen vacancies and molecular imprinting evidently enhanced the electrochemical oxidation signal of BPA. The sensor had a good linear response ranging from 0.01 μM to 20 μM with a limit of detection of 3.6 nM. Additionally, the sensor showed remarkable stability, reproducibility and interference resistant ability. It also exhibits excellent recovery during the detection of real water. These findings suggested that the sensor has the potential to be developed as a simple, efficient and low-cost monitoring system for the monitoring of BPA in water.

Graphene and gold nanoparticle-based bionanocomposite for the voltammetric determination of bisphenol A in (micro)plastics

The monitoring of endocrine disruptors in the environment is one of the main strategies in the investigation of potential risks associated with exposure to these chemicals. Bisphenol A is one of the most prevalent endocrine-disrupting compounds and is prone to leaching out from polycarbonate plastic in both freshwater and marine environments. Additionally, microplastics also can leach out bisphenol A during their fragmentation in the water environment. In the quest for a highly sensitive sensor to determine bisphenol A in different matrices, an innovative bionanocomposite material has been achieved. This material is composed of gold nanoparticles and graphene, and was synthesized using a green approach that utilized guava (Psidium guajava) extract for reduction, stabilization, and dispersion purposes. Transmission electron microscopy images revealed well-spread gold nanoparticles with an average diameter of 31 nm on laminated graphene sheets in the composite material. An electrochemical sensor was developed by depositing the bionanocomposite onto a glassy carbon surface, which displayed remarkable responsiveness towards bisphenol A. Experimental conditions such as the amount of graphene, extract: water ratio of bionanocomposite and pH of the supporting electrolyte were optimized to improve the electrochemical performance. The modified electrode displayed a marked improvement in current responses for the oxidation of bisphenol A as compared to the uncovered glassy carbon electrode. A calibration plot was established for bisphenol A in 0.1 mol L^-1 Britton-Robinson buffer (pH 4.0), and the detection limit was determined to equal to 15.0 nmol L^-1. Recovery data from 92 to 109% were obtained in (micro)plastics samples using the electrochemical sensor and were compared with UV-vis spectrometry, demonstrating its successful application with accurate responses.

Exposure, toxicological mechanism of endocrine disrupting compounds and future direction of identification using nano-architectonics

Endocrine-disrupting compounds (EDC) are a group of exogenous chemicals that structurally mimic hormones and interfere with the hormonal signaling cascade. EDC interacts with hormone receptors, transcriptional activators, and co-activators, altering the signaling pathway at both genomic and non-genomic levels. Consequently, these compounds are responsible for adverse health ailments such as cancer, reproductive issues, obesity, and cardiovascular and neurological disorders. The persistent nature and increasing incidence of environmental contamination from anthropogenic and industrial effluents have become a global concern, resulting in a movement in both developed and developing countries to identify and estimate the degree of exposure to EDC. The U.S. Environment Protection Agency (EPA) has outlined a series of in vitro and in vivo assays to screen potential endocrine disruptors. However, the multidisciplinary nature and concerns over the widespread application demand alternative and practical techniques for identifying and estimating EDC. The review chronicles the state-of-art 20 years (1990-2023) of scientific literature regarding EDC's exposure and molecular mechanism, highlighting the toxicological effects on the biological system. Alteration in signaling mechanisms by representative endocrine disruptors such as bisphenol A (BPA), diethylstilbestrol (DES), and genistein has been emphasized. We further discuss the currently available assays and techniques for in vitro detection and propose the prominence of designing nano-architectonic-sensor substrates for on-site detection of EDC in the contaminated aqueous environment.

High sensitivity electrochemical detection of ultra-trace imidacloprid in fruits and vegetables using a Fe-rich FeCoNi-MOF

High sensitivity and ultra-trace detection of imidacloprid are important and challenging in the field of food. In this study, we prepared a Fe-rich FeCoNi-MOF in-situ modified nickel foam working electrode by one-step hydrothermal method, and achieved a highly sensitive detection of the imidacloprid. The characterization techniques confirmed that Fe-rich FeCoNi-MOF had excellent crystallinity, tighter structure, and exposed rich active sites. The detection results showed that Fe-rich FeCoNi-MOF electrochemical sensor had a minimum detection limit of 0.04 pmol/L (100 times lower than that of the bioelectrochemical sensors), a wide response range (1 pmol/L-120 μmol/L), and high sensitivity (124 μA pmol/L^-1 cm^-2). These advantages of the electrochemical sensor were revealed theoretically by the valence change of active metal and the first principle calculation. Lastly, the Fe-rich FeCoNi-MOF electrochemical sensor was applied to detect imidacloprid in apple, fresh tea leaves, tomato, cucumber, and had an excellent recovery of 98-102.8 %.

Novel Sensitive Electrochemical Immunosensor Development for the Selective Detection of HopQ H. pylori Bacteria Biomarker

Helicobacter pylori (H. pylori) is a highly contagious pathogenic bacterium that can cause gastrointestinal ulcers and may gradually lead to gastric cancer. H. pylori expresses the outer membrane HopQ protein at the earliest stages of infection. Therefore, HopQ is a highly reliable candidate as a biomarker for H. pylori detection in saliva samples. In this work, an H. pylori immunosensor is based on detecting HopQ as an H. pylori biomarker in saliva. The immunosensor was developed by surface modification of screen-printed carbon electrodes (SPCE) with MWCNT-COOH decorated with gold nanoparticles (AuNP) followed by HopQ capture antibody grafting on SPCE/MWCNT/AuNP surface using EDC/S-NHS chemistry. The sensor performance was investigated utilizing various methods, such as cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscope (SEM) coupled with energy-dispersive X-ray spectroscopy (EDX). H. pylori detection performance in spiked saliva samples was evaluated by square wave voltammetry (SWV). The sensor is suitable for HopQ detection with excellent sensitivity and linearity in the 10 pg/mL-100 ng/mL range, with a 2.0 pg/mL limit of detection (LOD) and an 8.6 pg/mL limit of quantification (LOQ). The sensor was tested in saliva at 10 ng/mL, and recovery of 107.6% was obtained by SWV. From Hill's model, the dissociation constant Kd for HopQ/HopQ antibody interaction is estimated to be 4.60 × 10^-10 mg/mL. The fabricated platform shows high selectivity, good stability, reproducibility, and cost-effectiveness for H. pylori early detection due to the proper choice of biomarker, the nanocomposite material utilization to boost the SPCE electrical performance, and the intrinsic selectivity of the antibody-antigen approach. Additionally, we provide insight into possible future aspects that researchers are recommended to focus on.

Sensitive and Selective Electrochemical Detection of Lead(II) Based on Waste-Biomass-Derived Carbon Quantum Dots@Zeolitic Imidazolate Framework-8

An electrochemical sensor based on carbon quantum dots (CQDs) and zeolitic imidazolate framework-8 (ZIF-8) composite was fabricated to detect lead(II). The CQDs (2.47 ± 0.52 nm) were synthesized from platanus acerifoli leaves by carbonization and the hydrothermal method. Under the optimal conditions, the fabricated electrochemical sensor had excellent performance in detecting Pb²⁺. The linear range for Pb²⁺ was 1 nM-1 μM, and the limit of detection (LOD) was 0.04 nM and the limit of quantification (LOQ) was 0.14 nM. Moreover, when the solution contained Pb²⁺ and Cd²⁺, the linear range for Pb²⁺ was 50 nM to 1 μM and the LOD was 0.02 nM. When the solution contained Pb²⁺ and Cu²⁺, the linear range for Pb²⁺ was 50 nM-750 nM and LOD was 0.07 nM. Furthermore, even if the solution contained Pb²⁺, Cd²⁺ and Cu²⁺, the linear range for Pb²⁺ was 50 nM-1 μM and the LOD was 0.04 nM. The X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrometer (FTIR) and Brunauer-Emmet-Teller (BET) results indicated that the composite electrode materials had abundant oxygen-containing functional groups, a large specific surface area and pore structure, which are conducive to the adsorption of heavy metal ions and improve the detection performance.

A cyclodextrin-based reagent for cis/trans-geometrical isomers separation by mobility measurements and chemical calculations

Identification of cis/trans-carbon-carbon double-bond (CC) isomers remain challenging. Herein, a simple and rapid method for the separation and analysis of cis/trans-maleic acid (MA) and aconitic acid (AA) using Trapped Ion Mobility Spectrometry (TIMS) was developed. α-, β-, γ-cyclodextrin (CD) were served as the separation reagent, slight difference in mobility separation was obtained by [CD-MA/AA-H]^-. Specially, with the addition of divalent metal ion (G²⁺) as coordination metal ion, the separation effect was much increased by [CD-MA/AA + G-H]⁺, and α-CD has better mobility separation effect than β-/γ-CD. Moreover, chemical calculations revealed the binary and ternary complexes are in the inclusion forms, and microscopic interactions between cis/trans-MA/AA, CDs, and G²⁺ are somewhat different that making their mobility separation. Finally, quantifications of cis/trans-isomers were analyzed in food samples, with good linearity (R² > 0.99) and recoveries obtained from 87.25 % to 100.73 %.

β-cyclodextrin-functionalized magnetic graphene oxide for the efficient enrichment of bisphenols in milk and milk packaging

In this work, β-cyclodextrin-functionalized magnetic graphene oxide (NiFe₂O₄@GO@β-CD) was synthesized and employed as magnetic solid-phase extraction adsorbent for the extraction of bisphenols before high performance liquid chromatography analysis. The modification of β-cyclodextrin could enhance the adsorption performance of NiFe₂O₄@GO@β-CD towards bisphenols through the host-guest interaction and hydrogen-bond interaction. Under the optimal conditions, good linearities between peak area and concentration of bisphenols (1 - 300 μg L^-1, r ≥ 0.9989) were obtained with the limits of detection (S/N = 3) in the range of 0.050 - 0.10 μg L^-1. The recoveries of bisphenols in milk and milk packaging ranged from 78.0% to 101.6%. Moreover, NiFe₂O₄@GO@β-CD showed stable chemical properties and good reusability with the recoveries of bisphenols remained above 80.0% after 12 MSPE cycles. The adsorption characteristics of NiFe₂O₄@GO@β-CD towards bisphenols fitted well with the pseudo-second-order kinetic model and Langmuir model. The hydrogen-bond interaction, π-π interaction, host-guest interaction and electrostatic interaction between sorbent and bisphenols played important role during the adsorption process. The developed method showed potential applications for the analysis of trace bisphenols in milk and milk packaging.

Highly sensitive detection of thyroglobulin based on sandwich-type electrochemical immunoassay

As a dimeric protein, thyroglobulin (Tg) is an important biomarker for different thyroid cancer (DTC), so designing effective method to detect Tg is of great significance. In this work, by preparing β-cyclodextrin (CD) functionalized carbon nanotubes (CNTs) nanohybrid (CD-CNTs) as carrier to immobilize primary antibody (Ab₁) of Tg, assembling sulfydryl ferrocene (Fc) and secondary antibody (Ab₂) on the surface of nanogold (Au) as signaling amplifier (Ab₂-Au-Fc), a simple and sensitive sandwich-type electrochemical immunoassay (STEM) of Tg was designed herein for the first time. In brief, CNTs show large surface area and conductivity, while CD offers superior host-guest recognition capability that can bound with Ab₁; meanwhile, Fc probe can offer stable electrochemical signal that is proportionable to the concentration of Tg. Under the optimum conditions, the proposed STEM platform shows excellent sensing results for Tg detection: a considerable low analytical detection (0.5 ng mL^-1) and wide linearity (2 to 200 ng mL^-1), suggesting the designed STEM platform offers potential real applications for detect Tg.

An electrochemical sensing platform based on carbon black and chitosan-stabilized platinum nanoparticles

The versatility of chitosan (Ch) biopolymer as a metallic nanoparticle stabilizing agent and excellent former of thin films on glassy carbon was explored in this work for the sustainable manufacture of novel electrochemical sensors based on carbon black (CB) and chitosan-stabilized platinum nanoparticles (Ch-PtNPs). Platinum nanoparticles highly stabilized by chitosan were easily synthesized at room temperature and characterized by HR-TEM, UV-vis, and voltammetry. Ch-PtNPs presented an average diameter of 2.7 nm, and typical voltammetric peaks of Pt in sulfuric acid medium were detected for films containing Ch-PtNPs. As a proof of concept, the CB-Ch-PtNP electrode was applied in the determination of hydrogen peroxide (H₂O₂) and the endocrine disruptor bisphenol A (BPA). Pronounced electrocatalytic activity towards H₂O₂ reduction was observed in the presence of Ch-PtNPs in the films, guaranteeing the non-enzymatic determination of H₂O₂ by chronoamperometry, with a limit of detection of 10 μmol L^-1. In the determination of BPA by differential pulse adsorptive anodic stripping voltammetry (DPAdASV), under optimal experimental conditions, a wide linear response range and a limit of detection at the nanomolar level (7.9 nmol L^-1) were achieved. In addition, excellent repeatabilities of sensor response and sensor fabrication, and accuracy in the analysis of natural water samples were obtained.

Magnetic Fe3O4 nanoparticles decorated phosphorus-doped biochar-attapulgite/bismuth film electrode for smartphone-operated wireless portable sensing of ultra-trace multiple heavy metal ions

Pollution caused by both forestry wastes and heavy metals has increasingly drawn attention owing to environmental safety concerns. After essential oil is extracted from Cinnamomum camphoras (L.), the branches are used as forestry wastes to prepare a phosphorus-doped biochar-attapulgite/bismuth film electrode decorated with magnetic Fe₃O₄ nanoparticles (MBA-BiFE). The smartphone-operated wireless portable sensor is employed for the simultaneous ultratrace voltammetric detection of multiple heavy metal ions (Cd²⁺, Pb²⁺, and Hg²⁺). Cd²⁺, Pb²⁺, and Hg²⁺ exhibit excellent electrochemical responses in linear ranges of 0.1 nM-5 μM, 0.01 nM-7 μM, and 0.1 nM-3 μM with limits of detection equal to 0.036, 0.003, and 0.011 nM, respectively. The recoveries of MBA-BiFE for Cd²⁺, Pb²⁺, and Hg²⁺ are 93.6-109.9%, 86.0-107.5%, and 94.8-104.6%, respectively, and the RSD values for repeated measurements of Cd²⁺, Pb²⁺, and Hg²⁺ are 4.2%, 2.8%, and 3.3%, respectively. A machine learning model based on an artificial neural network algorithm is constructed to enable a smart determination of ultratrace hazardous multiple metal ions. The portable sensor based on the screen-printed integrated three-electrode sensor modified using MBA-BiFE demonstrates advantages and practicability in outdoor detection, compared with conventional sensors based on MBA-BiFE. This study provides a smartphone-operated wireless portable sensing technique for high-potential applications in environmetallomics or agrometallomics using forestry waste-derived biochar as substrate for electrode preparation. HIGHLIGHTS: • Fe₃O₄ decorated phosphorus-doped biochar-attapulgite/bismuth film electrode. • A smartphone-operated sensor for analysis of multiple heavy metal ions. • An Artificial neural network model for smart analysis of Cd²⁺, Pb²⁺, and Hg²⁺.

Highly sensitive and selective serotonin (5-HT) electrochemical sensor based on ultrafine Fe3O4 nanoparticles anchored on carbon spheres

Neurotransmitter serotonin (5-HT) is involved in various physiological and pathological processes. Therefore, its highly sensitive and selective detection in human serum is of great significance for early diagnosis of disease. In this work, employing iron phthalocyanine as Fe source, ultrafine Fe₃O₄ nanoparticles anchored on carbon spheres (Fe₃O₄/CSs) have been prepared, which exhibits an excellent electrochemical sensing performance toward 5-HT. With carbonecous spheres turned into conductive carbon spheres under the heat treatment in N₂ atmosphere, iron phthalocyanine absorbed on their surfaces are simultaneously pyrolysised and oxidized, and finally transformed into ultrafine Fe₃O₄ nanoparticles. Electrochemical results demonstrate a high sensitivity (5.503 μA μM^-1) and a low detection limit (4 nM) toward 5-HT for as-prepared Fe₃O₄/CSs. In combination with the morphology and physicochemical property of Fe₃O₄/CSs, the enhanced sensing mechanism toward 5-HT is disscussed. In addition, the developed electrochemical sensor also displays a good sensing stability and an anti-interferent ability. Further applied in real human serum samples, a satisfactory recovery rate is achieved. Promisingly, the developed electrochemical sensor can be employed for the determination of 5-HT in actual samples.

An ultrasensitive electrochemical biosensor for bisphenol A based on aptamer-modified MrGO@AuNPs and ssDNA-functionalized AuNP@MBs synergistic amplification

Bisphenol A (BPA) is a harmful endocrine disruptor, sensitive and rapid quantification of BPA is highly desirable. In this work, a novel synergistic signal-amplifying electrochemical biosensor was developed for BPA detection by using a recognition probe (RP) constructed by BPA aptamer modified gold nanoparticles-loaded magnetic reduced graphene oxide (Aptamer-MrGO@AuNPs), and a signal probe (SP) constructed by BPA aptamer-complementary single-stranded DNA (ssDNA) functionalized methylene blue (MB)-loaded gold nanoparticle (ssDNA-AuNP@MBs). The RP and SP can self-assemble to form a stable RP-SP complex through complementary base pairing. The current intensity of the biosensor correlates with the number of RP-SP complexes. In the presence of BPA, the BPA aptamer can capture BPA with high selectivity and affinity, form an RP-BPA complex and dissociate the RP-SP complex to release SP, resulting in a decrease in the current signal intensity of the biosensor. A single AuNP could be loaded with multiple BPA aptamers and MBs, which improves the recognition efficiency and enhances the signal intensity. Due to the magnetic properties of MrGO@AuNPs, the magnetic separation and adsorption of RP or RP-SP complex is very convenient, enabling all reaction processes to be carried out in solution, which not only improves the mass transfer efficiency, but also simplifies the operation. Under optimal conditions, the developed biosensor had a detection limit as low as 0.141 pg/mL and had been successfully applied to the detection of real environmental water samples. Therefore, the synergistic signal amplification strategy of RP and SP has potential value in the detection of trace pollutants in the water environment.

Electropotential-Inspired Star-Shaped Gold Nanoconfined Multiwalled Carbon Nanotubes: A Proof-of-Concept Electrosensoring Interface for Lung Metastasis Biomarkers

Herein, an innovative way of designing a star-shaped gold nanoconfined multiwalled carbon nanotube-engineered sensoring interface (AuNS@MWCNT//GCE) is demonstrated for quantification of methionine (MTH); a proof of concept for lung metastasis. The customization of the AuNS@MWCNT is assisted by surface electrochemistry and thoroughly discussed using state-of-the-art analytical advances. Micrograph analysis proves the protrusion of nanotips on the surface of potentiostatically synthesized AuNPs and validates the hypothesis of Turkevich seed (AuNP)-mediated formation of AuNSs. In addition, a facile synthesis of electropotential-assisted transformation of MWCNTs to luminescent nitrogen-doped graphene quantum dots (N_d-GQDs avg. ∼4.3 nm) is unveiled. The sensor elucidates two dynamic responses as a function of C_MTH ranging from 2 to 250 μM and from 250 to 3000 μM with a detection limit (DL) of ∼0.20 μM, and is robust to interferents except for tiny response of a similar -SH group bearing Cys (<9.00%). The high sensitivity (0.44 μA·μM^-1·cm^-2) and selectivity of the sensor can be attributed to the strong hybridization of the Au nanoparticle with the sp² C atom of the MWCNTs, which makes them a powerful electron acceptor for Au-SH-MTH interaction as evidenced by density functional theory (DFT) calculations. The validation of the acceptable recovery of MTH in real serum and pharma samples by standard McCarthy-Sullivan assay reveals the holding of great promise to provide valuable information for early diagnosis as well as assessing the therapeutic consequence of lung metastasis.

Flexible Electrochemical Platform Coupled with In Situ Prepared Synthetic Receptors for Sensitive Detection of Bisphenol A

A flexible electrochemical sensor based on the carbon felt (CF) functionalized with Bisphenol A (BPA) synthetic receptors was developed. The artificial Bisphenol A receptors were grafted on the CF by a simple thermal polymerization molecular imprinting process. Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and electrochemical characterizations were used to analyze the receptors. Characterization results demonstrated that the Bisphenol A synthetic receptors successfully formed on the CFs surface. Because the synthetic receptor and the porous CFs were successfully combined, the sensor displayed a better current response once Bisphenol A was identified. The sensor's linear range was determined to be from 0.5 to 8.0 nM and 10.0 to 300.0 nM, with a detection limit of 0.36 nM. Even after being bent and stretched repeatedly, the electrode's performance was unaffected, demonstrating the robustness, adaptability and viability of installing the sensor on flat or curved surfaces for on-site detection. The designed electrochemical sensor has been used successfully to identify Bisphenol A in milk samples with satisfactory results. This work provided a promising platform for the design of implantable, portable and miniaturized sensors.

Recent Progress in Nanotechnology-Based Approaches for Food Monitoring

Throughout the food supply chain, including production, storage, and distribution, food can be contaminated by harmful chemicals and microorganisms, resulting in a severe threat to human health. In recent years, the rapid advancement and development of nanotechnology proposed revolutionary solutions to solve several problems in scientific and industrial areas, including food monitoring. Nanotechnology can be incorporated into chemical and biological sensors to improve analytical performance, such as response time, sensitivity, selectivity, reliability, and accuracy. Based on the characteristics of the contaminants and the detection methods, nanotechnology can be applied in different ways in order to improve conventional techniques. Nanomaterials such as nanoparticles, nanorods, nanosheets, nanocomposites, nanotubes, and nanowires provide various functions for the immobilization and labeling of contaminants in electrochemical and optical detection. This review summarizes the recent advances in nanotechnology for detecting chemical and biological contaminations in the food supply chain.

A novel bimetallic MOFs combined with gold nanoflakes in electrochemical sensor for measuring bisphenol A

In this paper, a novel bimetallic Fe-Cu metal-organic framework combined with 1,3,5-benzenetricarboxylic acid (Fe-Cu-BTC) are synthesized using hydrothermal reaction. The bimetallic Fe-Cu-BTC with high BET (1504 cm³ g^-1) and high Langmuir surface area (1831 cm³ g^-1) is composited by gold nanoparticles to improve the conductivity and to develop their synergistic effect. A novel bisphenol A (BPA) sensor was prepared by dropcasting Fe-Cu-BTC on glassy carbon electrodes (GCE) followed by AuNPs electrodeposition. The Fe-Cu-BTC framework were characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy studies (TEM), FT-IR, BET measurements and EDX spectra. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) were carried out for surveying the electrochemical properties of the sensors and for the quantification of BPA. Two linear ranges of BPA concentrations 0.1-1.0 μM and 1.0-18 μM with 18 nM limit of detection were obtained. The developed sensor was used to measure the concentration of BPA in samples extracted from rain coat with the recovery ranging from 85.70 to 103.23%.

Sodium Dodecyl Sulfate-Mediated Graphene Sensor for Electrochemical Detection of the Antibiotic Drug: Ciprofloxacin

The present study involves detecting and determining CIP by a new electrochemical sensor based on graphene (Gr) in the presence of sodium dodecyl sulfate (SDS) employing voltammetric techniques. Surface morphology studies of the sensing material were analyzed using a scanning electron microscope (SEM) and atomic force microscope (AFM). In the electroanalysis of CIP at the developed electrode, an enhanced anodic peak response was recorded, suggesting the electro-oxidation of CIP at the electrode surface. Furthermore, we evaluated the impact of the electrolytic solution, scan rate, accumulation time, and concentration variation on the electrochemical behavior of CIP. The possible electrode mechanism was proposed based on the acquired experimental information. A concentration variation study was performed using differential pulse voltammetry (DPV) in the lower concentration range, and the fabricated electrode achieved a detection limit of 2.9 × 10^-8 M. The proposed sensor detected CIP in pharmaceutical and biological samples. The findings displayed good recovery, with 93.8% for tablet analysis and 93.3% to 98.7% for urine analysis. The stability of a developed electrode was tested by inter- and intraday analysis.

Multisensory Systems Based on Perfluorosulfonic Acid Membranes Modified with Functionalized CNTs for Determination of Sulfamethoxazole and Trimethoprim in Pharmaceuticals

Sulfamethoxazole and trimethoprim are synthetic bacteriostatic drugs. A potentiometric multisensory system for the analysis of sulfamethoxazole and trimethoprim combination drugs was developed. Perfluorosulfonic acid membranes containing functionalized CNTs were used as the sensor materials. The CNTs' surface was modified by carboxyl, sulfonic acid, or (3-aminopropyl)trimethoxysilanol groups. The influence of the CNT concentration and the properties of their surface, as well as preliminary ultrasonic treatment of the polymer and CNT solution before the casting of hybrid membranes, on their ion-exchange capacity, water uptake, and transport properties was revealed. Cross-sensitivity of the sensors to the analytes was achieved due to ion exchange and hydrophobic interactions with hybrid membranes. An array of cross-sensitive sensors based on the membranes containing 1.0 wt% of CNTs with sulfonic acid or (3-aminopropyl)trimethoxysilanol groups enabled us to provide the simultaneous determination of sulfamethoxazole and trimethoprim in aqueous solutions with a concentration ranging from 1.0 × 10^-5 to 1.0 × 10^-3 M (pH 4.53-8.31). The detection limits of sulfamethoxazole and trimethoprim were 3.5 × 10^-7 and 1.3 × 10^-7 М. The relative errors of sulfamethoxazole and trimethoprim determination in the combination drug as compared with the content declared by the manufacturer were 4% (at 6% RSD) and 5% (at 7% RSD).

Highly Sensitive Electrochemical Detection of Paraquat in Environmental Water Samples Using a Vertically Ordered Mesoporous Silica Film and a Nanocarbon Composite

Herein, we demonstrate a sensitive and rapid electrochemical method for the detection of paraquat (PQ) using a glassy carbon electrode (GCE) modified with vertically ordered mesoporous silica films (VMSF) and a nanocarbon composite. The three-dimensional graphene-carbon nanotube (3DG-CNT) nanocarbon composite has a 3D network structure, a large electroactive area and oxygen-containing groups, promoting electron transfer between PQ and the underlying electrode and providing a suitable microenvironment for the stable growth of VMSF. This VMSF/3DG-CNT nanocomposite film could be prepared on the GCE's surface by a two-step electrochemical method with good controllability and convenience. Owing to the synergistic effect of the electrocatalytic ability of 3DG-CNT and the electrostatically enriched capacity of VMSF, the proposed VMSF/3DG-CNT/GCE has superior analytical sensitivity compared with the bare GCE. Furthermore, VMSF has excellent anti-fouling ability that makes the fabricated sensor exhibit satisfactory performance for direct analysis of PQ in environmental water samples.

Probe-Integrated Label-Free Electrochemical Immunosensor Based on Binary Nanocarbon Composites for Detection of CA19-9

Convenient and sensitive detection of tumor biomarkers is crucial for the early diagnosis and treatment of cancer. Herein, we present a probe-integrated and label-free electrochemical immunosensor based on binary nanocarbon composites and surface-immobilized methylene blue (MB) redox probes for detection of carbohydrate antigen 199 (CA19-9), which is closely associated with gastric malignancies. Nanocarbon composites consisting of electrochemically reduced graphene oxides and carbon nanotubes (ErGO-CNT) are electrodeposited onto an indium tin oxide (ITO) electrode surface to form a 3D nanocomposite film, which could provide high surface area to immobilize abundant MB probes, facilitate the electron transfer of MB, and therefore, improve sensitivity. Polydopamine (PDA) served as a bifunctional linker is able to immobilize anti-CA19-9 antibodies and stabilize the inner probe, conferring the sensing interface with specific recognition capacity. Electrochemical detection of CA19-9 is achieved based on the decrease of the redox signal of MB after specific binding of CA19-9 with a wide linear range of 0.1 mU/mL to 100 U/mL and a limit of detection (LOD) of 0.54 nU/mL (S/N = 3). The constructed electrochemical immunosensor has good selectivity, repeatability, reproducibility, and stability. Furthermore, determination of CA19-9 in human serum samples is also realized.