Bubble-Nucleation-Based Method for the Selective and Sensitive Electrochemical Detection of Surfactants

Per- and poly-fluoroalkyl substances (PFAS) sensing: A focus on representatively sampling soil vadose zones linked to nano-sensors

Per- and poly-fluoroalkyl substances (PFAS) are a group of organo-fluorine compounds that have been broadly used in consumer and industrial products spanning virtually all sectors. They can be found as surfactants, coatings and liners, polymer additives, fire retardants, adhesives, and many more. The chemical stability of the carbon fluorine bond and amphiphilic nature of PFAS result in their persistence and mobility in the environment via soil porewater, surface water and groundwater, with potential for adverse effects on the environment and human health. There is an emergent and increasing requirement for fast, low-cost, robust, and portable methods to detect PFAS, especially in the field. There may be thousands of PFAS compounds present in soil and water at extremely low concentration (0.01-250 ppb) that require measurement, and traditional technologies for continuous environmental sensing are challenged due to the complexity of soil chemistry. This paper presents a comprehensive review of potentially rapid PFAS measurement methods, focused on techniques for representative sampling of PFAS in porewater from contaminated soil, and approaches for pre-treatment of porewater samples to eliminate these interferences to be ready for PFAS-detecting sensors. The review discusses selectivity, a key factor underlying pre-treatment and sensing performance, and explores the interactions between PFAS and various sensors. PFAS chemical nano-sensors discussed are categorized in terms of the detection mechanism (electrochemical and optical). This review aims to provide guidance and outline the current challenges and implications for future routine PFAS sensing linked to soil porewater collection, to achieve more selective and effective PFAS sensors.

Sensitive quantitation of ultra-trace toxic aconitines in complex matrices by perfusion nano-electrospray ionization mass spectrometry combined with gas-liquid microextraction

The accurate analysis of ultra-trace (e.g. <10-4 ng/mL) substances in complex matrices is a burdensome but vital problem in pharmaceutical analysis, with important implications for precise quality control of drugs, discovery of innovative medicines and elucidation of pharmacological mechanisms. Herein, an innovative constant-flow perfusion nano-electrospray ionization (PnESI) technique was developed firstly features significant quantitative advantages in high-sensitivity ambient MS analysis of complex matrix sample. More importantly, double-labeled addition enrichment quantitation strategies of gas-liquid microextraction (GLME) were proposed for the first time, allowing highly selective extraction and enrichment of specific target analytes in a green and ultra-efficient (>1000-fold) manner. Using complex processed Aconitum herbs as example, PnESI-MS directly enabled the qualitative and absolute quantitative analysis of the processed Aconitum extracts and characterized the target toxic diester alkaloids with high sensitivity, high stability, wide linearity range, and strong resistance to matrix interference. Further, GLME device was applied to obtain the highly specific enrichment of the target diester alkaloids more than 1000-fold, and accurate absolute quantitation of trace aconitine, mesaconitine, and hypaconitine in the extracts of Heishunpian, Zhichuanwu and Zhicaowu was accomplished (e.g., 0.098 pg/mL and 0.143 pg/mL), with the quantitation results well below the LODs of aconitines from any analytical instruments available. This study built a systematic strategy for accurate quantitation of ultra-trace substances in complex matrix sample and expected to provide a technological revolution in many fields of pharmaceutical research.

Unveiling nano-empowered catalytic mechanisms for PFAS sensing, removal and destruction in water

Per- and polyfluoroalkyl substances (PFAS) are organofluorine compounds used to manufacture various industrial and consumer goods. Due to their excellent physical and thermal stability ascribed to the strong CF bond, these are ubiquitously present globally and difficult to remediate. Extensive toxicological and epidemiological studies have confirmed these substances to cause adverse health effects. With the increasing literature on the environmental impact of PFAS, the regulations and research have also expanded. Researchers worldwide are working on the detection and remediation of PFAS. Many methods have been developed for their sensing, removal, and destruction. Amongst these methods, nanotechnology has emerged as a sustainable and affordable solution due to its tunable surface properties, high sorption capacities, and excellent reactivities. This review comprehensively discusses the recently developed nanoengineered materials used for detecting, sequestering, and destroying PFAS from aqueous matrices. Innovative designs of nanocomposites and their efficiency for the sensing, removal, and degradation of these persistent pollutants are reviewed, and key insights are analyzed. The mechanistic details and evidence available to support the cleavage of the CF bond during the treatment of PFAS in water are critically examined. Moreover, it highlights the challenges during PFAS quantification and analysis, including the analysis of intermediates in transitioning nanotechnologies from the laboratory to the field.

Fabrication of an Optoplasmonic Raft with Improved SERS Performance Detecting Methamphetamine through Bubble Enrichment

In this work, a novel raft-like structure that combines noble metal nanoparticles (NPs) with an interconnected layer of hemispherical dielectric shell was fabricated and characterized. It was discovered that this hybrid material can enhance the optoplasmonic interaction between plasmonic and dielectric components, thereby improving the sensing performance in surface-enhanced Raman spectroscopy (SERS). Varied geometric parameters of the fabricated optoplasmonic raft, including the inner diameter and thickness of the dielectric shell, were attempted and analyzed through numerical simulation and experimental SERS measurements. With particular size, thickness, and incident orientation, the silica shell focuses the incident optical flow into the deposited silver NPs, undergoing similar near-field focusing behavior in comparison with other optoplasmonic entities. This optoplasmonic raft floating on the water surface is able to harvest the target molecules effectively through bubble enrichment, which rapidly captures and concentrates analytes from the aqueous phase. With a limited sampling time, the sensing performance of the developed optoplasmonic raft is improved by applying the optimized parameters involved in bubble enrichment. The substrates and corresponding enrichment method were implemented in the detection of methamphetamine (METH), achieving a limit of detection (LOD) down to 0.035 nM. As for practical onsite detection, the developed substrate and bubbling strategy were applied in an assembled set, employing a portable Raman spectrometer and an air pump. This set is able to detect METH dissolved in regular commercial beer, which is quite competent in the investigation of drug abuse.

Luminescence Lifetime-Based Sensing Platform Based on Cyclometalated Iridium(III) Complexes for the Detection of Perfluorooctanoic Acid in Aqueous Samples

Luminescence lifetimes are an attractive analytical method for detection due to its high sensitivity and stability. Iridium probes exhibit luminescence with long excited-state lifetimes, which are sensitive to the local environment. Perfluorooctanoic acid (PFOA) is listed as a chemical of high concern regarding its toxicity and is classified as a "forever chemical". In addition to strict limits on the presence of PFOA in drinking water, environmental contamination from industrial effluent or chemical spills requires rapid, simple, accurate, and cost-effective analysis in order to aid containment. Herein, we report the fabrication and function of a novel and facile luminescence sensor for PFOA based on iridium modified on gold surfaces. These surfaces were modified with lipophilic iridium complexes bearing alkyl chains, namely, IrC6 and IrC12, and Zonyl-FSA surfactant. Upon addition of PFOA, the modified surfaces IrC6-FSA@Au and IrC12-FSA @Au show the largest change in the red luminescence signal with changes in the luminescence lifetime that allow monitoring of PFOA concentrations in aqueous solutions. The platform was tested for the measurement of PFOA in aqueous samples spiked with known concentrations of PFOA and demonstrated the capacity to determine PFOA at concentrations >100 μg/L (240 nM).

Detection of Per- and Polyfluoroalkyl Substances (PFAS) by Interrupted Energy Transfer

The ubiquitous presence of per- and polyfluoroalkyl substances (PFAS) in aqueous environments has aroused societal concern. Nonetheless, effective sensing technologies for continuous monitoring of PFAS within water distribution infrastructures currently do not exist. Herein, we describe a ratiometric sensing approach to selectively detect aqueous perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) at concentrations of μg ⋅ L-1 . Our method relies on the excitonic transport in a highly fluorinated poly(p-phenylene ethynylene) to amplify a ratiometric emission signal modulated by an embedded fluorinated squaraine dye. The electronic coupling between the polymer and dye occurs through overlap of π-orbitals and is designed such that energy transfer is dominated by an electron-exchange (Dexter) mechanism. Exposure to aqueous solutions of PFAS perturbs the orbital interactions between the squaraine dye and the polymer backbone, thereby diminishing the efficiency of the energy transfer and producing a "polymer-ON/dye-OFF" response. These polymer/dye combinations were evaluated in spin-coated films and polymer nanoparticles and were able to selectively detect PFAS at concentrations of ca. 150 ppb and ca. 50 ppb, respectively. Both polymer films and nanoparticles are not affected by the type of water, and similar responses to PFAS were found in milliQ and well water.

Nanoelectrochemistry in electrochemical phase transition reactions

Electrochemical phase transition is important in a range of processes, including gas generation in fuel cells and electrolyzers, as well as in electrodeposition in battery and metal production. Nucleation is the first step in these phase transition reactions. A deep understanding of the kinetics, and mechanism of the nucleation and the structure of the nuclei and nucleation sites is fundamentally important. In this perspective, theories and methods for studying electrochemical nucleation are briefly reviewed, with an emphasis on nanoelectrochemistry and single-entity electrochemistry approaches. Perspectives on open questions and potential future approaches are also discussed.

Research Progress of Perfluoroalkyl Substances in Edible Oil-A Review

Perfluoroalkyl substances (PFASs) have been widely used in different types of consumer and industrial applications such as surfactants, household cleaning products, textiles, carpets, cosmetics, firefighting foams, and food packaging because of their good stability and special physicochemical properties of hydrophobicity, oleophobicity, high temperature resistance, etc. Meanwhile, PFASs are considered an emerging organic pollutant due to their persistence and potential toxicity to human health. PFASs occur in edible oil, an important component of the global diet, mainly in three ways: raw material contamination, process contamination, and migration from oil contact materials. Thus, the occurrence of PFAS in edible oils has drawn more and more attention in recent years. In this work, the pertinent literature of the last two decades from the Web of Science database was researched. This review systematically addressed the potential sources, the contamination levels, and the progress of the determination of PFASs in edible oil. It aims to provide a relatively whole profile of PFASs in edible oil, render assistance to minimise human exposure to PFASs, and standardise the detection methods of perfluoroalkyl substances in edible oil.

Ultra-sensitive SERS detection of perfluorooctanoic acid based on self-assembled p-phenylenediamine nanoparticle complex

PFOA is a representative perfluorinated compound that is used as a surfactant in various industrial fields. However, because PFOA has severe side effects due to its strong toxicity, such as carcinogenesis, liver damage, and immune system damage, it is crucial to enable PFOA detection with high sensitivity. Herein, we developed a perfluorooctanoic acid (PFOA) surface-enhanced Raman scattering (SERS) sensor using self-assembled p-phenylenediamine (SAp-PD) nanoparticles and an Ag SERS substrate. For the ultra-sensitive detection of PFOA, we synthesized and optimized SAp-PD, which shows a decrease in SERS intensities when reacting with PFOA. Using the Ag nanograss SERS substrate, the change in intensity that resulted from the SAp-PD and PFOA reaction was amplified. Consequently, we detected the 1.28 pM (detection limit) of PFOA in distilled water. Moreover, PFOA molecules were successfully detected in samples of the PFOA-coated frying pan and rice extraction at concentrations up to 1.69 nM and 10.3 μM, respectively.

Ultratrace PFAS Detection Using Amplifying Fluorescent Polymers

Per- and poly(fluoroalkyl) substances (PFAS) are environmentally persistent pollutants that are of growing concern due to their detrimental effects at ultratrace concentrations (ng·L^-1) in human and environmental health. Suitable technologies for on-site ultratrace detection of PFAS do not exist and current methods require complex and specialized equipment, making the monitoring of PFAS in distributed water infrastructures extremely challenging. Herein, we describe amplifying fluorescent polymers (AFPs) that can selectively detect perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) at concentrations of ng·L^-1. The AFPs are highly fluorinated and have poly(p-phenylene ethynylene) and polyfluorene backbones bearing pyridine-based selectors that react with acidic PFAS via a proton-transfer reaction. The fluorinated regions within the polymers partition PFAS into polymers, whereas the protonated pyridine units create lower-energy traps for the excitons, and emission from these pyridinium sites results in red-shifting of the fluorescence spectra. The AFPs are evaluated in thin-film and nanoparticle forms and can selectively detect PFAS concentrations of ∼1 ppb and ∼100 ppt, respectively. Both polymer films and nanoparticles are not affected by the type of water, and similar responses to PFAS were found in milliQ water, DI water, and well water. These results demonstrate a promising sensing approach for on-site detection of aqueous PFAS in the ng·L^-1 range.

Sensor technologies for the detection and monitoring of endocrine-disrupting chemicals

Endocrine-disrupting chemicals (EDCs) are a class of man-made substances with potential to disrupt the standard function of the endocrine system. These EDCs include phthalates, perchlorates, phenols, some heavy metals, furans, dimethoate, aromatic hydrocarbons, some pesticides, and per- and polyfluoroalkyl substances (PFAS). EDCs are widespread in the environment given their frequent use in daily life. Their production, usage, and consumption have increased many-fold in recent years. Their ability to interact and mimic normal endocrine functions makes them a potential threat to human health, aquatics, and wild life. Detection of these toxins has predominantly been done by mass spectroscopy and/or chromatography-based methods and to a lesser extent by advanced sensing approaches such as electrochemical and/or colorimetric methods. Instrument-based analytical techniques are often not amenable for onsite detection due to the lab-based nature of these detecting systems. Alternatively, analytical approaches based on sensor/biosensor techniques are more attractive because they are rapid, portable, equally sensitive, and eco-friendly. Advanced sensing systems have been adopted to detect a range of EDCs in the environment and food production systems. This review will focus on advances and developments in portable sensing techniques for EDCs, encompassing electrochemical, colorimetric, optical, aptamer-based, and microbial sensing approaches. We have also delineated the advantages and limitations of some of these sensing techniques and discussed future developments in sensor technology for the environmental sensing of EDCs.

Target-triggered double fluorescent biosensors for rapid and sensitive detection of long-chain perfluorinated compounds using DNA probe and lysozyme fiber

Perfluorinated compounds (PFCs) are useful man-made chemicals and serve as new emerging organic pollutants due to their environmental and health concerns. Chromatography-mass detection methods often need complex procedure and are also too expensive, so there is a critical demand to develop rapid, inexpensive, easy-to-operate and sensitive methods for PFCs detection. In this work, double fluorescent biosensors ('DT sensor' and 'FT sensor') have been designed to quantitatively detect long-chain perfluorinated compounds (PFCs), due to their strong hydrophobic interaction with DNA probe or lysozyme fiber. The ratio and rapid fluorescence responses offered more obvious signal changes, and high sensitivity with a limit of detection (LOD) of 0.16 μM (98.2 ppb) for perfluorododecanoic acid (PFDoA). For three PFCs with longer perfluoroalkyl chain (CF₂), increased detection sensitivity was achieved due to a stronger hydrophobicity. The fluorescent biosensors showed a good selectivity for long-chain PFCs and served as cross-reactive sensors to differentiate three different long-chain PFCs. The biosensors also had robust signal response in tap water or serum samples, and the LOD can be further lowered to pM (ppt) level after sample preconcentration.

Alternative methods of monitoring emerging contaminants in water: a review

Anthropogenic activities have steadily increased the release of emerging contaminants (ECs) in aquatic bodies, and these ECs may have adverse effects on humans even at their trace (μg L^-1) levels. Their occurrence in wastewater systems is more common, and the current wastewater treatment facilities are inefficient in eliminating many of such persistent ECs. "Gold standard" techniques such as chromatography, mass spectrometry, and other high-resolution mass spectrometers are used for the quantification of ECs of various kinds, but they all have significant limitations. This paper reviews the alternative methods for EC detection, which include voltammetry, potentiometry, amperometry, electrochemical impedance spectroscopy (EIS) based electrochemical methods, colorimetry, surface-enhanced Raman spectroscopy (SERS), fluorescence probes, and fluorescence spectroscopy-based optical techniques. These alternative techniques have several advantages over conventional techniques, including low sample volume, excludes solid phase extraction procedure, high sensitivity, selectivity, portability, reproducibility, rapidity, low cost, and the ability to monitor ECs in real time. This review summarises each of the alternative methods for detecting ECs in water samples and their respective limits of detection (LODs). The sensitivity of each technique varied depending on the type of EC measured, type of electrochemical probe and electrode, substrates, type of nanoparticle (NP), the physicochemical parameters of water samples tested, and more. Nevertheless, this paper also focuses on some of the current challenges encountered by these alternative methods in monitoring ECs.

Investigating the cytotoxic redox mechanism of PFOS within Hep G2 by hyperspectral-assisted scanning electrochemical microscopy

Perfluorooctane sulfonate (PFOS) is one of the most lethal per- and poly-fluoroalkyl substances (PFAS). Generally, exposure effects are studied through case-controlled studies, cohort studies, or cell assays. Unfortunately, most studies involving two-dimensional cell cultures require cell lysis or fixation. For in vitro studies, fluorescence microscopy has been useful, but methods to simultaneously discern phototoxic effects during an experiment are limited. Here, we use hepatocarcinoma (Hep G2) cells to examine the redox mechanism of PFOS cytotoxicity in vitro, while using hyperspectral-assisted scanning electrochemical microscopy (SECM) to differentiate between PFOS and redox mediator induced stress. Specifically, we correlate an increase in the electrochemical response of ferrocenemethanol oxidation with an increase in intracellular reactive oxygen species. Corresponding hyperspectral images of redox indicative-fluorophores implicate superoxide in the cytotoxic redox mechanism.

Detection methods for sub-nanogram level of emerging pollutants - Per and polyfluoroalkyl substances

Per- and polyfluoroalkyl substances (PFAS) are organofluorine compounds has been manufactured for more than five decades and used in different purposes. Among persistent organic pollutants, PFAS are toxic, bioaccumulative in humans, wildlife, and global environment. As per environmental protection agency (EPA) guidelines, the perfluorooctanoate and perfluorooctane sulfonate permissible limit was 0.07 ng/L in drinking water. When the concentration exceeds the acceptable limit, it has negative consequences for humans. In such a case, PFAS monitoring is critical, and a quick detection technique are highly needed. Health departments and regulatory agencies have interests in monitoring of PFAS presences and exposures. For the detection of PFAS, numerous highly precise and sensitive chromatographic methods are available. However, the drawbacks of analytical techniques include timely sample preparations and the lack of on-site applicability. As a result, there is an increasing demand for simple sensor systems for monitoring of PFAS in real field samples. In this review, we first describe the sample pre-treatment and analytical techniques for the detection of PFAS. Second, we broadly discussed available sensor system for the quantification of PFAS in different filed samples. Finally, future trends in PFASs sensor are also presented.

Highly efficient preconcentration using anodically generated shrinking gas bubbles for per- and polyfluoroalkyl substances (PFAS) detection

Here we report a highly efficient PFAS preconcentration method that uses anodically generated shrinking gas bubbles to preconcentrate PFAS via aerosol formation, achieving ~ 1400-fold enrichment of PFOS and PFOA-the two most common PFAS-in 20 min. This new method improves the enrichment factor by 15 to 105% relative to the previous method that uses cathodically generated H₂ bubbles. The shrinking gas bubbles are in situ electrogenerated by oxidizing water in an NH₄HCO₃ solution. H⁺ produced by water oxidation reacts with HCO₃^- to generate CO₂ gas, forming gas bubbles containing a mixture of O₂ and CO₂. Due to the high solubility of CO₂ in aqueous solutions, the CO₂/O₂ bubbles start shrinking when they leave the electrode surface region. A mechanistic study reveals two reasons for the improvement: (1) shrinking bubbles increase the enrichment rate, and (2) the attractive interactions between the positively charged anode and negatively charged PFAS provide high enrichment at zero bubble path length. Based on this preconcentration method, we demonstrate the detection of ≥ 70 ng/L PFOA and PFOS in water in ~ 20 min by coupling it with our bubble-nucleation-based detection method, fulfilling the need of the US Environmental Protection Agency.

Detection of PFAS and Fluorinated Surfactants Using Differential Behaviors at Interfaces of Complex Droplets

Contamination of per- and polyfluoroalkyl substances (PFAS) in water supplies will continue to have serious health and environmental consequences. Despite the importance of monitoring the concentrations of PFAS at potential sites of contamination and at treatment plants, there are few suitable and rapid on-site methods. Many nonconventional techniques do not possess the necessary selectivity and sensitivity to distinguish PFAS from other surface-active components and to quantify the low concentrations in real-world conditions. Herein, we report a novel and rapid method for the detection of perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) by leveraging their differential behaviors at the interfaces of emissive complex droplets. Measurement of surface and interfacial tensions via a force tensiometer reveals that PFAS preferentially self-assemble at the water-fluorocarbon oil interface (F/W) rather than the water-hydrocarbon oil interface (H/W). We also observe an opposite behavior for hydrocarbon surfactants. This difference in interfacial behavior produces distinct effects on the morphological change and optical emission of biphasic oil-in-water droplets. The change in the intensity of fluorescence emission, measured with a simple spectroscopic setup, correlates with the concentrations of PFAS. We also demonstrate that the range of detection and sensitivity can be tuned by adjusting the initial composition of the complex droplets. Our results illustrate an alternative mode of sensors that may provide a rapid and on-site detection of PFAS.

Nano-enabled sensing of per-/poly-fluoroalkyl substances (PFAS) from aqueous systems - A review

Per-/poly-fluoroalkyl substances (PFAS) are an emerging class of environmental contaminants used as an additive across various commodity and fire-retardant products, for their unique thermo-chemical stability, and to alter their surface properties towards selective liquid repellence. These properties also make PFAS highly persistent and mobile across various environmental compartments, leading to bioaccumulation, and causing acute ecotoxicity at all trophic levels particularly to human populations, thus increasing the need for monitoring at their repositories or usage sites. In this review, current nano-enabled methods towards PFAS sensing and its monitoring in wastewater are critically discussed and benchmarked against conventional detection methods. The discussion correlates the materials' properties to the sensitivity, responsiveness, and reproducibility of the sensing performance for nano-enabled sensors in currently explored electrochemical, spectrophotometric, colorimetric, optical, fluorometric, and biochemical with limits of detection of 1.02 × 10^-6 μg/L, 2.8 μg/L, 1 μg/L, 0.13 μg/L, 6.0 × 10^-5 μg/L, and 4.141 × 10^-7 μg/L respectively. The cost-effectiveness of sensing platforms plays an important role in the on-site analysis success and upscalability of nano-enabled sensors. Environmental monitoring of PFAS is a step closer to PFAS remediation. Electrochemical and biosensing methods have proven to be the most reliable tools for future PFAS sensing endeavors with very promising detection limits in an aqueous matrix, short detection times, and ease of fabrication.

Rapid and Direct Perfluorooctanoic Acid Sensing with Selective Ionomer Coatings on Screen-Printed Electrodes under Environmentally Relevant Concentrations

Per- and polyfluoroalkyl substances (PFASs) pose a significant health threat to humans at trace levels. Because of its ubiquity across the globe, there have been intense efforts to rapidly quantify PFASs in the environment while also mitigating their release. This work reports an electrochemical sensor with a selective perfluorinated anion exchange ionomer (PFAEI) coating for direct sensing of perfluorooctanoic acid (PFOA)-a type of PFAS. Notably, the sensor operates without the need of redox probes and has a limit of detection around 6.51 ± 0.2 ppb (15 nM) in buffered deionized water and drinking water. By testing the sensor with different ionomer electrode coatings, it was inferred that the PFAEI favors PFOA anions over other competing anions in solution through a combination of electrostatic and van der Waal interactions.

Selectivity of Per- and Polyfluoroalkyl Substance Sensors and Sorbents in Water

Per- and polyfluoroalkyl substances (PFAS) are a large group of engineered chemicals that have been widely used in industrial production. PFAS have drawn increasing attention due to their frequent occurrence in the aquatic environment and their toxicity to animals and humans. Developing effective and efficient detection and remediation methods for PFAS in aquatic systems is critical to mitigate ongoing exposure and promote water reuse. Adsorption-based removal is the most common method for PFAS remediation since it avoids hazardous byproducts; in situ sensing technology is a promising approach for PFAS monitoring due to its fast response, easy operation, and portability. This review summarizes current materials and devices that have been demonstrated for PFAS adsorption and sensing. Selectivity, the key factor underlying both sensor and sorbent performance, is discussed by exploring the interactions between PFAS and various probes. Examples of selective probes will be presented and classified by fluorinated groups, cationic groups, and cavitary groups, and their synergistic effects will also be analyzed. This review aims to provide guidance and implication for future material design toward more selective and effective PFAS sensors and sorbents.

Exposure, health effects, sensing, and remediation of the emerging PFAS contaminants - Scientific challenges and potential research directions

Per- and polyfluoroalkyl substances (PFAS) make up a large group of persistent anthropogenic chemicals which are difficult to degrade and/or destroy. PFAS are an emerging class of contaminants, but little is known about the long-term health effects related to exposure. In addition, technologies to identify levels of contamination in the environment and to remediate contaminated sites are currently inadequate. In this opinion-type discussion paper, a team of researchers from the University of Connecticut and the University at Albany discuss the scientific challenges in their specific but intertwined PFAS research areas, including rapid and low-cost detection, energy-saving remediation, the role of T helper cells in immunotoxicity, and the biochemical and molecular effects of PFAS among community residents with measurable PFAS concentrations. Potential research directions that may be employed to address those challenges and improve the understanding of sensing, remediation, exposure to, and health effects of PFAS are then presented. We hope our account of emerging problems related to PFAS contamination will encourage a broad range of scientific experts to bring these research initiatives addressing PFAS into play on a national scale.

Yale School of Public Health Symposium: An overview of the challenges and opportunities associated with per- and polyfluoroalkyl substances (PFAS)

On December 13, 2019, the Yale School of Public Health hosted a symposium titled "Per- and Polyfluoroalkyl Substances (PFAS): Challenges and Opportunities" in New Haven, Connecticut. The meeting focused on the current state of the science on these chemicals, highlighted the challenges unique to PFAS, and explored promising opportunities for addressing them. It brought together participants from Yale University, the National Institute of Environmental Health Sciences, the University of Massachusetts Amherst, the University of Connecticut, the Connecticut Agricultural Experiment Station, the Connecticut Departments of Public Health and Energy and Environmental Protection, and the public and private sectors. Presentations during the symposium centered around several primary themes. The first reviewed the current state of the science on the health effects associated with PFAS exposure and noted key areas that warranted future research. As research in this field relies on specialized laboratory analyses, the second theme considered commercially available methods for PFAS analysis as well as several emerging analytical approaches that support health studies and facilitate the investigation of a broader range of PFAS. Since mitigation of PFAS exposure requires prevention and cleanup of contamination, the third theme highlighted new nanotechnology-enabled PFAS remediation technologies and explored the potential of green chemistry to develop safer alternatives to PFAS. The fourth theme covered collaborative efforts to assess the vulnerability of in-state private wells and small public water supplies to PFAS contamination by adjacent landfills, and the fifth focused on strategies that promote successful community engagement. This symposium supported a unique interdisciplinary coalition established during the development of Connecticut's PFAS Action Plan, and discussions occurring throughout the symposium revealed opportunities for collaborations among Connecticut scientists, state and local officials, and community advocates. In doing so, it bolstered the State of Connecticut's efforts to implement the ambitious initiatives that its PFAS Action Plan recommends.

Recent progress in the detection of emerging contaminants PFASs

As an emerging contaminant, per- and polyfluoroalkyl substances (PFASs) make up a large group of persistent anthropogenic chemicals, which are difficult to degrade in the environment. Notwithstanding their wide range of applications in consumer products and industrial processes, PFASs have been detected in the environment as well as in human body. Due to their potential adverse human health effects, the U.S. Environmental Protection Agency (EPA) set the combined concentration of PFOA and PFOS in drinking water at 70 ng/L or 70 ppt (parts per trillion) as a lifetime health advisory level. Current standard detection methods for PFASs heavily rely on chromatographic techniques coupled with mass spectrometry. Although these methods provide accurate, specific, and sensitive measurements, their applications are greatly limited in advanced analytical laboratories because it necessitates expensive instrumentations, professional operators, complicated sample pretreatment, and considerable analysis time. Therefore, other detection methods beyond chromatographic based techniques, such as optical and electrochemical techniques, have also been extensively explored for simple, accessible, inexpensive, rapid, and sensitive detection of PFASs, particularly PFOA and PFOS. The purpose of this review is to provide recent progress in alternative detection platforms relying on non-MS based techniques for PFASs analysis. Starting with a brief introduction about the importance of monitoring PFASs, recent advances in various PFASs detection methods are grouped and discussed based on the difference of signals, with an emphasis on the working principles of different techniques, the sensing mechanism, and the sensing performance. The review is closed with the conclusion and discussion of future trends.

A method for detecting perfluorooctanoic acid and perfluorooctane sulfonate in water samples using genetically engineered bacterial biosensor

A simple, reagent and pre-treatment (i.e. dilution, sample purification and pH adjustment) free approach based genetically engineered bacterial biosensor is developed and demonstrated for the detection of perfluorinated compounds in water samples. The bacterial biosensor was developed by integrating two genes called regulatory (defluorinase gene) and reporter gene (green fluorescence gene) through genetic engineering techniques. The as-developed bacterial biosensor was employed to detect perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) in water samples upon induction of regulatory gene and expression of green fluorescence protein. The induced fluorescence emission by the biosensor was visualized using fluorescence microscopic images. The specificity of biosensor was evaluated with different types of organic pollutants such as chlorinated compounds, polyaromatic hydrocarbons and pesticides etc., in both presence and absence of PFOA and PFOS. The biosensor was employed to detect the perfluorinated compounds at nano gram level in both standard solutions and natural water samples like river water, wastewater and drinking water with an analysis time of 24 h. The detection of PFOA and PFOS by the developed-bacterial sensor is validated by liquid chromatography coupled with mass spectrometer. The developed biosensor has demonstrated a rapid and sensitive detection of PFOA and PFOS in various water samples.

Harnessing bubble behaviors for developing new analytical strategies

Gas bubbles are easily accessible and offer many unique characteristic properties of a gas/liquid two-phase system for developing new analytical methods. In this minireview, we discuss the newly developed analytical strategies that harness the behaviors of bubbles. Recent advancements include the utilization of the gas/liquid interfacial activity of bubbles for detection and preconcentration of surface-active compounds; the employment of the gas phase properties of bubbles for acoustic imaging and detection, microfluidic analysis, electrochemical sensing, and emission spectroscopy; and the application of the mass transport behaviors at the gas/liquid interface in gas sensing, biosensing, and nanofluidics. These studies have demonstrated the versatility of gas bubbles as a platform for developing new analytical strategies.

On-site, rapid and visual method for nanomolar Hg2+ detection based on the thymine–Hg2+–thymine triggered “double” aggregation of Au nanoparticles enhancing the Tyndall effect

This work describes a new nanosensor for the simple, rapid, portable, colorimetric analysis of mercury(ii) (Hg²⁺) ions by combining the sensitive Tyndall effect (TE) of colloidal Au nanoparticles (AuNPs) with specific thymine–Hg²⁺–thymine (T–Hg²⁺–T) coordination chemistry for the first time. For the TE-inspired assay (TEA), in the presence of Hg²⁺ in a sample, the analyte can selectively mediate the hybridization of three types of flexible single-stranded DNAs (ssDNAs) to form stable rigid double-stranded DNAs (dsDNAs) via the T–Hg²⁺–T ligand interaction. Subsequent self-assembly of the dsDNAs with terminal thiol groups on the AuNPs' surfaces led to their “double” aggregation in addition to the lack of sufficient ssDNAs as the stabilizing molecules in a high-salt solution, resulting in a remarkably enhanced TE signal that positively relied on the Hg²⁺ level. The results demonstrated that such a TEA method enabled rapid naked-eye qualitative analysis of 625 nM Hg²⁺ within 10 min with an inexpensive laser pointer pen as an inexpensive handheld light source to generate the TE response. Making use of a smartphone for portable TE readout could further quantitatively detect the Hg²⁺ ions in a linear concentration range from 156 to 2500 nM with a limit of detection as low as 25 nM. Moreover, the developed equipment-free nanosensor was also used to analyze the Hg²⁺ ions in real samples including tap water, drinking water, and pond water, the obtained recoveries were within the range of 93.68 to 108.71%. To the best of our knowledge, this is the first report of using the AuNPs and functional nucleic acids to design a TE-based biosensor for the analysis of highly toxic heavy metal ions.

A new equipment-free colorimetric nanosensor was initially developed for quantitative point-of-need detection of nanomolar Hg²⁺ ions based on the enhancement in Tyndall effect of Au nanoparticles via their target-triggered “double” aggregation.

Facing the Challenge of Poly- and Perfluoroalkyl Substances in Water: Is Electrochemical Oxidation the Answer?

Electrochemical treatment systems have the unique ability to completely mineralize poly- and perfluoroalkyl substances (PFASs) through potential-driven electron transfer reactions. In this review, we discuss the state-of-the-art on electrooxidation of PFASs in water, aiming at elucidating the impact of different operational and design parameters, as well as reported mechanisms of PFAS degradation at the anode surface. We have identified several shortcomings of the existing studies that are largely limited to small-scale laboratory batch systems and unrealistic synthetic solutions, which makes extrapolation of the obtained data to real-world applications difficult. PFASs are surfactant molecules, which display significant concentration-dependence on adsorption, electrosorption, and dissociation. Electrooxidation experiments conducted with high initial PFAS concentration and/or in high conductivity supporting electrolytes likely overestimate process performance. In addition, the formation of organohalogen byproducts, chlorate and perchlorate, was seldom considered. Nevertheless, the first step toward advancing from laboratory-scale to industrial-scale applications is recognizing both the strengths and limitations of electrochemical water treatment systems. More comprehensive and rigorous evaluation of novel electrode materials, application of scalable proof-of-concept studies, and acknowledgment of all treatment outputs (not just the positive ones) are imperative. The presence of PFASs in drinking water and in the environment is an urgent global public health issue. Developments made in material science and application of novel three-dimensional, porous electrode materials and nanostructured coatings are forging a path toward more sustainable water treatment technologies and potential chemical-free treatment of PFAS-contaminated water.

Detection of perfluorooctane sulfonate by ion-transfer stripping voltammetry at an array of microinterfaces between two immiscible electrolyte solutions

Per- and polyfluoroalkyl substances (PFAS) are a category of persistent environmental contaminants that have been linked to health issues in humans. In this work, we investigate the detection of perfluorooctanesulfonate (PFOS-), one such PFAS, by ion-transfer voltammetry at an array of microinterfaces between two immiscible electrolyte solutions (μITIES). Cyclic voltammetry, differential pulse voltammetry and differential pulse stripping voltammetry (DPSV) indicated the ion-transfer behaviour and detection of PFOS-, with the latter enabling detection at picomolar concentrations. Using a 5 min preconcentration time, during which PFOS- was preconcentrated into the organic phase of the μITIES array, a limit of detection (LOD) of 0.03 nM (0.015 μg L-1) in aqueous electrolyte was achieved. This performance is attributed to the enhanced mass transport (radial diffusion) to the μITIES that occurs during preconcentration. To investigate the potentiality for applications of this analytical approach to environmental samples, measurements in a range of water matrices were investigated. Drinking water, laboratory tap water and seawater matrices were assessed by spiking with PFOS- over the 0.1-1 nM range. A matrix effect was observed, with changes in sensitivity and LOD relative to those in pure aqueous electrolyte solutions. Such matrix effects need to be considered in designing applications of these PFOS- measurements to environmental samples. The results presented here indicate that DPSV at a μITIES array can form the basis for a fast and sensitive screening method for PFOS- contamination that is suited to portable and on-site applications.

Recent Developments of PFAS-Detecting Sensors and Future Direction: A Review

Per- and poly-fluoroalkyl substances (PFASs) have recently been labeled as toxic constituents that exist in many aqueous environments. However, traditional methods used to determine the level of PFASs are often not appropriate for continuous environmental monitoring and management. Based on the current state of research, PFAS-detecting sensors have surfaced as a promising method of determination. These sensors are an innovative solution with characteristics that allow for in situ, low-cost, and easy-to-use capabilities. This paper presents a comprehensive review of the recent developments in PFAS-detecting sensors, and why the literature on determination methods has shifted in this direction compared to the traditional methods used. PFAS-detecting sensors discussed herein are primarily categorized in terms of the detection mechanism used. The topics covered also include the current limitations, as well as insight on the future direction of PFAS analyses. This paper is expected to be useful for the smart sensing technology development of PFAS detection methods and the associated environmental management best practices in smart cities of the future.

An integrated microfluidic device for studying controllable gas embolism induced cellular responses

Gas embolism is the abnormal emergence of bubble in the vascular system, which can induce local ischemic symptoms. For studying the mechanism underlying gas embolism and revealing local ischemic diseases information, novel technique for analyzing cells response to bubble contact with high controllability is highly desired. In this paper, we present an integrated microfluidic device for the precise generation and control of microbubble based on the gas permeability of polydimethysiloxane (PDMS) to study the effect of bubble's mechanical contact on cells. Cell viability analysis demonstrated that short-term (<15 min) bubble contact was generally non-lethal to cultured endothelial cells. The significant increase in intracellular calcium of the microbubble-contacted cells and cell-to-cell propagation of calcium signal in the adjacent cells were observed during the process of bubble expansion. In addition, the analysis of intercellular calcium signal in the cells treated with suramin and octanol revealed that cell-released small nucleotides and gap junction played an important role in regulating the propagation of calcium wave triggered by bubble contact. Thus, our microfluidic method provides an effective platform for studying the effect of gas embolism on cultured adherent cells and can be further needed for anti-embolism drugs test.

Determining the Subnanometer Thickness of the Water-Depletion Layer at the Interface between Water and the Hydrophobic Substrate

Surface plasmon resonance (SPR) is one of the most popular and powerful techniques for label-free detecting and quantitatively analyzing the interfacial refractive index (RI). So far, most of the SPR measurements are mainly applied to detect the relative change of RI upon biological and chemical events occurring at the interface, while the determinations on the absolute value of RI remains challenging. However, the absolute value of RI has become increasingly urgent in some cases, such as the existence and physical properties of the water depletion layer (WDL). WDL refers to a subnanometer-thick layer with reduced density between water and the hydrophobic substrate. The detailed explanations of how water meets hydrophobic surface have been studied by several kinds of techniques for decades but it remains under debate. In this work, we successfully established a method to measure the absolute RI at a gold-liquid interface by surface plasmon resonance microscopy (SPRM) and 2D Fourier transformation image processing and further applied this method to study the existence and physical nature of WDL. It was found that a 0.6 nm thick WDL existed at the interface of water and the hydrophobic substrate, leading to a reduced refractive index of 1.3295 ± 0.0006 compared with the standard value of 1.3325. Our results further indicated that the WDL consisted of a uniform layer rather than numerous isolated surface nanobubbles that distributed at the interface with high density.