HCl-Tolerant HxPO4/RuOx-CeO2 Catalysts for Extremely Efficient Catalytic Elimination of Chlorinated VOCs

Characteristics of catalytic destruction of dichloromethane and ethyl acetate mixture over HxPO4-RuOx/CeO2 catalyst

Catalytic destruction is an ascendant technology for the abatement of volatile organic compounds (VOCs) originating from solvent-based industrial processes. The varied composition tends to influence each VOC's catalytic behavior in the reaction mixture. We investigated the catalytic destruction of multi-component VOCs including dichloromethane (DCM) and ethyl acetate (EA), as representatives from pharmaceutical waste gases, over co-supported HxPO4-RuOx/CeO2 catalyst. A mutual inhibitory effect relating to concentrations because of competitive adsorption was verified in the binary VOCs oxidation and EA posed a more negative effect on DCM oxidation owing to EA's superior adsorption capacity. Preferential adsorption of EA on acidic sites (HxPO4/CeO2) promoted DCM activation on basic sites (O2-) and the dominating EA oxidation blocked DCM's access to oxidation centers (RuOx/CeO2), resulting in boosted monochloromethane yield and increased chlorine deposition for DCM oxidation. The impaired redox ability of Ru species owing to chlorine deposition in turn jeopardized deep oxidation of EA and its by-products, leading to increased gaseous by-products such as acetic acid originating from EA pyrolysis. Notably, DCM at low concentration slightly promoted EA conversion at low temperatures with or without water, consistent with the enhanced EA adsorption in co-adsorption analyses. This was mainly due to that DCM impeded the shielding effect of hydrolysate deposition from rapid EA hydrolysis depending on the decreased acidity. Moreover, water benefited EA hydrolysis but decreased CO2 selectivity while the generated water derived from EA was likely to affect DCM transformation. This work may provide theoretical guidance for the promotion of applied catalysts toward industrial applications.

Photothermal Catalytic Removal of 1,2-DCE with High HCl Selectivity over the Brønsted Acid-Enriched Sulfur-Doped MOFs

Chlorinated volatile organic compounds come from a wide range of sources and are highly toxic, posing a serious threat to biological health and the environment. Herein, a high-efficiency and energy-saving photothermal synergistic catalytic oxidation method was developed for the removal of 1,2-dichloroethane (1,2-DCE). Compared to traditional thermocatalysis, the 1,2-DCE conversion over Ru-U6S in photothermal synergistic catalysis at 340 °C increased by approximately 44% not only reducing energy consumption but also avoiding the instability of MOF structure caused by high reaction temperature. The excellent photothermal catalytic oxidation activity was derived from the synergistic effect of photo- and thermocatalysis. Ru-U6S demonstrated excellent 1,2-DCE adsorption capacity and stronger light utilization and could produce more reactive oxygen species (•OH and •O2-) after light illumination, which participated in the oxidation reaction, promoting the release of the active site of the catalyst. The results of H2O-TPD and NH3-DRIFTS exhibited that the use of S-containing ligands in the synthesis process increased the hydroxyl groups and Brønsted acid sites, significantly improved the selectivity of CO2 and HCl in the oxidation process, and reduced the release of chlorine-containing byproducts. This work provides a high-efficiency and energy-saving strategy for removing chlorinated volatile organic compounds and increasing the selectivity of ideal products directly with MOFs directly.

Enhancement of Mineralization Ability and Water Resistance of Vanadium-Based Catalysts for Catalytic Oxidation of Chlorobenzene by Platinum Loading

The design of a catalyst with multifunctional sites is one of the effective methods for low-temperature catalytic oxidation of chlorinated volatile organic compounds (CVOCs). The loss of redox sites and competitive adsorption of H2O prevalent in the treatment of industrial exhaust gases are the main reasons for the weak mineralization ability and poor water vapor resistance of V-based catalysts. In this work, platinum (Pt) is selected to combine with the V/CeO2 catalyst, which provides more redox sites and H2O dissociative activation sites and further enhances its catalytic performance. The results show that PtV/CeO2 achieves 90% of the CO2 yield at 318 °C and maintains excellent catalytic activity rather than continuous deactivation within 15 h after water vapor injection. The formation of Pt-O-V bonds enhances the redox ability and promotes deep oxidation of polychlorinated intermediates, accounting for the significantly improved mineralization ability of PtV/CeO2. The dissociative activation effect of Pt on H2O molecules strengthens the migration and activation of V-adsorbed H2O, precluding V-poisoning and notably improving water resistance. This study lays a solid foundation for the efficient degradation of chlorobenzene under humid conditions.

Boosting Catalytic and Anti-fluorination Performance of the Ru/Vanadia-Titania Catalyst for the Oxidative Destruction of Freon by Sulfuric Acid Modification

Chlorofluorocarbons (CFCs) exert a strong greenhouse effect and constitute the largest contributor to ozone depletion. Catalytic removal is considered an effective pathway for eliminating low-concentration CFCs under mild conditions. The key issue is the easy deactivation of the catalysts due to their surface fluorination. We herein report a comparative investigation on catalytic dichlorodifluoromethane (CFC-12) removal in the absence or presence of water over the sulfuric-acid-modified three-dimensionally ordered macroporous vanadia-titania-supported Ru (S-Ru/3DOM VTO) catalysts. The S-Ru/3DOM VTO catalyst exhibited high activity (T90% = 278 °C at space velocity = 40 000 mL g-1 h-1) and good stability within 60 h of on-stream reaction in the presence of 1800 ppm of water due to the improvements in acid site amount and redox ability that promoted the adsorption of CFC-12 and the activation of C-F bonds. Compared with the case under dry conditions, catalytic performance for CFC-12 removal was better over the S-Ru/3DOM VTO catalyst in the presence of water. Water introduction mitigated surface fluorination by the replenishment of hydroxyl groups, inhibited the formation of halogenated byproducts via the surface fluorine species cleaning effect, and promoted the reaction pathway of COX2 (X = Cl/F) → carboxylic acid → CO2.

Unveiling the Function of Oxygen Vacancy on Facet-Dependent CeO2 for the Catalytic Destruction of Monochloromethane: Guidance for Industrial Catalyst Design

Secondary pollution remains a critical challenge for the catalytic destruction of chlorinated volatile organic compounds (CVOCs). By employing experimental studies and theoretical calculations, we provide valuable insights into the catalytic behaviors exhibited by ceria rods, cubes, and octahedra for monochloromethane (MCM) destruction, shedding light on the elementary reactions over facet-dependent CeO2. Our findings demonstrate that CeO2 nanorods with the (110) facet exhibit the best performance in MCM destruction, and the role of vacancies is mainly to form a longer distance (4.63 Å) of frustrated Lewis pairs (FLPs) compared to the stoichiometric surface, thereby enhancing the activation of MCM molecules. Subsequent molecular orbital analysis showed that the adsorption of MCM mainly transferred electrons from the 3σ and 4π* orbitals to the Ce 4f orbitals, and the activation was mainly caused by weakening of the 3σ bonding orbitals. Furthermore, isotopic experiments and theoretical calculations demonstrated that the hydrogen chloride generated is mainly derived from methyl in MCM rather than from water, and the primary function of water is to form excess saturated H on the surface, facilitating the desorption of generated hydrogen chloride.

Catalytic degradation of chlorinated volatile organic compounds (CVOCs) over Ce-Mn-Ti composite oxide catalysts

Developing industrially moldable catalysts with harmonized redox performance and acidity is of great significance for the efficient disposal of chlorinated volatile organic compounds (CVOCs) in actual exhaust gasses. Here, commercial TiO2, typically used for molding catalysts, was chosen as the carrier to fabricate a series of Ce0.02Mn0-0.24TiOx materials with different Mn doping ratios and employed for chlorobenzene (CB) destruction. The introduction of Mn remarkedly facilitated the synergistic effect of each element via the electron transfer processes: Ce3++Mn4+/3+↔Ce4++Mn3+/2+ and Mn4+/3++Ti4+↔Mn3+/2++Ti3+. These synergistic interactions in Ce0.02Mn0.04-0.24TiOx, especially Ce0.02Mn0.16TiOx, significantly elevated the active oxygen species, oxygen vacancies and redox properties, endowing the superior catalytic oxidation of CB. When the Mn doping amount increased to 0.24, a separate Mn3O4 phase appeared, which in turn might weaken the synergistic effect. Furthermore, the acidity of Ce0.02Mn0.04-0.24TiOx was decreased with the Mn doping, regulating the balance of redox property and acidity. Notably, Ce0.02Mn0.16TiOx featured relatively abundant B-acid sites. Its coordinating redox ability and moderate acidity promoted the deep oxidation of CB and RCOOH- intermediates, as well as the rapid desorption of Cl species, thus obtaining sustainable reactivity. In comparison, CeTiOx owned the strongest acidity, however, its poor redox property was not sufficient for the timely oxidative decomposition of the easier adsorbed CB, resulting in its rapid deactivation. This finding provides a promising strategy for the construction of efficient commercial molding catalysts to decompose the industrial-scale CVOCs.

Efficient Catalytic Elimination of Chlorobenzene Based on the Water Vapor-Promoting Effect within Mn-Based Catalysts: Activity Enhancement and Polychlorinated Byproduct Inhibition

Achieving no or low polychlorinated byproduct selectivity is essential for the chlorinated volatile organic compounds (CVOCs) degradation, and the positive roles of water vapor may contribute to this goal. Herein, the oxidation behaviors of chlorobenzene over typical Mn-based catalysts (MnO2 and acid-modified MnO2) under dry and humid conditions were fully explored. The results showed that the presence of water vapor significantly facilitates the deep mineralization of chlorobenzene and restrains the formation of Cl2 and dichlorobenzene. This remarkable water vapor-promoting effect was conferred by the MnO2 substrate, which could suitably synergize with the postconstructed acidic sites, leading to good activity, stability, and desirable product distribution of acid-modified MnO2 catalysts under humid conditions. A series of experiments including isotope-traced (D2O and H218O) CB-TPO provided complete insights into the direct involvement of water molecules in chlorobenzene oxidation reaction and attributed the root cause of the water vapor-promoting effect to the proton-rich environment and highly reactive water-source oxygen species rather than to the commonly assumed cleaning effect or hydrogen proton transfer processes (generation of active OOH). This work demonstrates the application potential of Mn-based catalysts in CVOCs elimination under practical application conditions (containing water vapor) and provides the guidance for the development of superior industrial catalysts.

The enhancement of benzene total oxidation over RuxCeO2 catalysts at low temperature: The significance of Ru incorporation

Catalytic oxidation is considered to be the most efficient technology for eliminating benzene from waste gas. The challenge is the reduction of the catalytic reaction temperature for the deep oxidation of benzene. Here, highly efficient RuxCeO2 catalysts were utilized to turn the number of surface oxygen vacancies and Ce-O-Ru bonds via a one-step hydrothermal method, resulting in a preferable low-temperature reducibility for the total oxidation of benzene. The T50 of the Ru0.2CeO2 catalyst for benzene oxidation was 135 °C, which was better than that of pristine CeO2 (239 °C) and 0.2Ru/CeO2 (190 °C). The superior performance of Ru0.2CeO2 was attributed to its large surface area (approximately 114.23 m2·g-1), abundant surface oxygen vacancies, and Ce-O-Ru bonds. The incorporation of Ru into the CeO2 lattice could effectively facilitate the destruction of the CeO bond and the facile release of lattice oxygen, inducing the generation of surface oxygen vacancies. Meanwhile, the bridging action of Ce-O-Ru bonds accelerated electron transfer and lattice oxygen transportation, which had a synergistic effect with surface oxygen vacancies to reduce the reaction temperature. The Ru0.2CeO2 catalyst also exhibited high catalytic stability, water tolerance, and impact resistance in terms of benzene abatement. Using in situ infrared spectroscopy, it was demonstrated that the Ru0.2CeO2 catalyst can effectively enhance the accumulation of maleate species, which are key intermediates for benzene ring opening, thereby enhancing the deep oxidation of benzene.

Electron Donation from Boron Suboxides via Strong p-d Orbital Hybridization Boosts Molecular O2 Activation on Ru/TiO2 for Low-Temperature Dibromomethane Oxidation

Low-temperature catalytic oxidation is of significance to the degradation of halogenated volatile organic compounds (HVOCs) to avoid hazardous byproducts with low energy consumption. Efficient molecular oxygen (O2) activation is pivotal to it but usually limited by the insufficient electron cloud density at the metal center. Herein, Ru-B catalysts with enhanced electron density around Ru were designed to achieve efficient O2 activation, realizing dibromomethane (DBM) degradation T90 at 182 °C on RuB1/TiO2 (about 30 °C lower than pristine Ru/TiO2) with a TOFRu value of 0.055 s-1 (over 8 times that of Ru/TiO2). Compared to the limited electron transfer (0.02 e) on pristine Ru/TiO2, the Ru center gained sufficient negative charges (0.31 e) from BOx via strong p-d orbital hybridization. The Ru-B site then acted as the electron donor complexing with the 2π* antibonding orbital of O2 to realize the O2 dissociative activation. The reactive oxygen species formed thereby could initiate a fast conversion and oxidation of formate intermediates, thus eventually boosting the low-temperature catalytic activity. Furthermore, we found that the Ru-B sites for O2 activation have adaptation for pollutant removal and multiple metal availability. Our study shed light on robust O2 activation catalyst design based on electron density adjustment by boron.

Three-dimensional porous CuO-modified CeO2-Al2O3 catalysts with chlorine resistance for simultaneous catalytic oxidation of chlorobenzene and mercury: Cu-Ce interaction and structure

Chlorine poisoning effects are still challenging to develop efficient catalysts for applications in chlorobenzene (CB) and mercury (Hg⁰) oxidation. Herein, three-dimensional porous CuO-modified CeO₂-Al₂O₃ catalysts with macroporous framework and mesoporous walls prepared via a dual template method were employed to study simultaneous oxidation of CB and Hg⁰. CuO-modified CeO₂-Al₂O₃ catalysts with three-dimensional porous structure exhibited outstanding activity and stability for simultaneous catalytic oxidation of CB and Hg⁰. The results demonstrated that the addition of CuO into CeO₂-Al₂O₃ can simultaneously enhance the acid sites and redox properties through the electronic inductive effect between CuO and CeO₂ (Cu²⁺+Ce³⁺↔Cu⁺+Ce⁴⁺). Importantly, the synergistic effect between Cu and Ce species can induce abundant oxygen vacancies formation, produce more reactive oxygen species and facilitate oxygen migration, which is beneficial for the deep oxidation of chlorinated intermediates. Moreover, macroporous framework and mesoporous nanostructure dramatically improved the specific surface area for enhancing the contact efficiency between reactants and active sites, leading to a remarkable decrease of byproducts deposition. CB and Hg⁰ had function of mutual promotion in this reaction system. In tune with the experimental results, the possible mechanistic pathways for simultaneous catalytic oxidation of CB and Hg⁰ were proposed.

Crystal Engineering of TiO2 for Enhanced Catalytic Oxidation of 1,2-Dichloroethane on a Pt/TiO2 Catalyst

Crystal engineering of metal oxide supports represents an emerging strategy to improve the catalytic performance of noble metal catalysts in catalytic oxidation of chlorinated volatile organic compounds (CVOCs). Herein, Pt catalysts on a TiO₂ support with different crystal phases (rutile, anatase, and mixed phase (P25)) were prepared for catalytic oxidation of 1,2-dichloroethane (DCE). The Pt catalyst on P25-TiO₂ (Pt/TiO₂-P) showed optimal activity, selectivity, and stability, even under high-space velocity and humidity conditions. Due to the strong interaction between Pt and P25-TiO₂ originating from the more lattice defects of TiO₂, the Pt/TiO₂-P catalyst possessed stable Pt⁰ and Pt²⁺ species during DCE oxidation and superior redox property, resulting in high activity and stability. Furthermore, the Pt/TiO₂-P catalyst possessed abundant hydroxyl groups, which prompted the removal of chlorine species in the form of HCl and significantly decreased the selectivity of vinyl chloride (VC) as the main byproduct. On the other hand, the Pt/TiO₂-P catalyst exhibited a different reaction path, in which the hydroxyl groups on its surface activated DCE to form VC and enolic species, besides the lattice oxygen of TiO₂ for the Pt catalysts on rutile and anatase TiO₂. This work provides guidance for the rational design of catalysts for CVOCs.

Catalytic Decomposition Mechanism of PH3 on 3DCuO/C and High Value Utilization of Deactivated Catalysts

With the widespread application of lithium iron phosphate batteries, the production capacity of the yellow phosphorus industry has increased sharply, and the treatment of the highly toxic by-product PH₃ is facing severe challenges. In this study, a 3D copper-based catalyst (3DCuO/C) that can efficiently decompose PH₃ at low temperatures and low oxygen concentrations is synthesized. The PH₃ capacity is up to 181.41 mg g^-1 , which is superior to that previously reported in the literature. Further studies indicated that the special 3D structure of 3DCuO/C induces oxygen vacancies on the surface of CuO, which is beneficial to the activation of O₂ , and then promotes the adsorption and dissociation of PH₃ . The doping of P after dissociation determines the formation of Cu-P, and the eventual conversion to Cu₃ P leads to the deactivation of CuO active sites. More strikingly, due to the appearance of Cu₃ P, the deactivated De-3DCuO/C (Cu₃ P/C) exhibited significant activity in the photocatalytic degradation of rhodamine B and photocatalytic oxidation of Hg⁰ (gas) and can also be a candidate as an anode material for Li batteries after modification, which will provide a more thorough and economical treatment scheme for deactivated catalysts.

Balancing acid and redox sites of phosphorylated CeO2 catalysts for NOx reduction: The promoting and inhibiting mechanism of phosphorus

The role of phosphorus in metal oxide catalysts is still controversial. The precise tuning of the acidic and redox properties of metal oxide catalysts for the selective catalytic reduction in NO_x using NH₃ is also a great challenge. Herein, CeO₂ catalysts with different degrees of phosphorylation were used to study the balance between the acidity and redox property by promoting and inhibiting effects of phosphorus. CeO₂ catalysts phosphorylated with lower phosphorus content (5 wt%) exhibited superior NO_x reduction performance with above 90% NO_x conversion during 240-420 °C due to the balanced acidity and reducibility derived from the highest content of Brønsted acid sites on PO₄^3- to adsorb NH₃ and surface adsorbed oxygen species. Plenty of PO₃^- over CeO₂ catalysts phosphorylated with the higher phosphorus content (≥ 10 wt%) significantly disrupted the balance between the acidity and the redox property due to the reduced acid/redox sites, which resulted in the less active NO_x species. The mechanism of different structural phosphorus species (PO₄^3- and PO₃^-) in promoting or inhibiting the NO_x reduction over CeO₂ catalysts was revealed. This work provides a novel method for qualitative and quantitative study of the relationship between acidity/redox property and activity of catalysts for NO_x reduction.

Pt/CeO2 coated with polyoxometallate chainmail to regulate oxidation of chlorobenzene without hazardous by-products

Doping noble metal and acid functionalization were both valid approaches to facilitate oxidation of chlorobenzene on CeO₂-based catalysts, but their promotion effects were influenced by different orders of modification process. Because of strong interaction between metal and support and proper redox nature of CeO₂, Pt NPs were re-dispersed into single atoms on CeO₂ surface via "ex-solution". Companied with Pt loading, the enhancement of oxidizing ability led to generation of polychlorinated by-products. Herein, CeO₂-supported Pt was coated by HSiW chainmail to protect Pt from being exposed to Cl-contained atmosphere, and HSiW coating promoted activation of chlorobenzene. The as-prepared chainmail catalyst of HSiW/Pt/CeO₂ displayed a remarkable performance in catalyzing oxidation of chlorobenzene without any dichlorobenzene at realistic condition. By comparison, other catalysts with exposed Pt suffered from production of toxic by-products.

Simultaneously Constructing Active Sites and Regulating Mn-O Strength of Ru-Substituted Perovskite for Efficient Oxidation and Hydrolysis Oxidation of Chlorobenzene

Chlorinated volatile organic compounds (CVOCs) are a class of hazardous pollutants that severely threaten environmental safety and human health. Although the catalytic oxidation technique for CVOCs elimination is effective, enhancing the catalytic efficiency and simultaneously inhibiting the production of organic byproducts is still of great challenge. Herein, Ru-substituted LaMn(Ru)O_{3+ δ} perovskite with Ru-O-Mn structure and weakened Mn-O bond strength has been developed for catalytic oxidation of chlorobenzene (CB). The formed Ru-O-Mn structure serves as favorable sites for CB adsorption and activation, while the weakening of Mn-O bond strength facilitates the formation of active oxygen species and improves oxygen mobility and catalyst reducibility. Therefore, LaMn(Ru)O_{3+ δ} exhibits superior low-temperature activity with the temperature of 90% CB conversion decreasing by over 90 °C compared with pristine perovskite, and the deep oxidation of chlorinated byproducts produced in low temperature is also accelerated. Furthermore, the introduction of water vapor into reaction system triggers the process of hydrolysis oxidation that promotes CB destruction and inhibits the generation of chlorinated byproducts, due to the higher-activity *OOH species generated from the dissociated H₂ O reacting with adsorbed oxygen. This work can provide a unique, high-efficiency, and facile strategy for CVOCs degradation and environmental improvement.

Chlorine-Coordinated Pd Single Atom Enhanced the Chlorine Resistance for Volatile Organic Compound Degradation: Mechanism Study

The development of catalysts with high chlorine resistance for volatile organic compound (VOC) degradation is of great significance to achieve air purification. Herein, Pd@ZrO₂ catalysts with monodispersed Pd atoms coordinated with Cl were prepared using an in situ grown Zr-based metal-organic framework (MOF) as the sacrifice templates to enhance the chlorine resistance for VOC elimination. The residual Cl species from the Zr-MOF coordinated with Pd, forming Pd₁-Cl species during the pyrolysis. Meanwhile, abundant oxygen vacancies (V_O) were generated, which enhanced the adsorption and activation of gaseous oxygen molecules, accelerating the degradation of VOCs. In addition, the Pd@ZrO₂ catalysts exhibited satisfactory water resistance, long-term stability, and great resistance to CO and dichloromethane (DCM) for VOC elimination. In situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) results elucidated that the generation of Pd₁-Cl species in Pd@ZrO₂ suppressed the absorption of DCM, releasing more active sites for toluene and its intermediate adsorption. Simultaneously, the monodispersed Pd atoms and V_O improved the reactivity of gaseous oxygen molecule adsorption and dissociation, boosting the deep decomposition of toluene and its intermediates. This work may provide a new strategy for rationally designing high-chlorine resistance catalysts for VOC elimination to improve the atmospheric environment.

Insights into Chlorobenzene Catalytic Oxidation over Noble Metal Loading {001}-TiO2: The Role of NaBH4 and Subnanometer Ru Undergoing Stable Ru0Ru4+ Circulation

Catalytic combustion of ubiquitous chlorinated volatile organic compounds (CVOCs) encounters bottlenecks regarding catalyst deactivation by chlorine poisoning and generation of toxic polychlorinated byproducts. Herein, Ru, Pd, and Rh were loaded on {001}-TiO₂ for thermal catalytic oxidation of chlorobenzene (CB), with Ru/{001}-TiO₂ representing superior reactivity, CO₂ selectivity, and stability in the 1000 min on-stream test. Interestingly, both acid sites and reactive active oxygen species (ROS) were remarkably promoted via adding NaBH₄. But merely enhancing these active sites of the catalyst in CVOC treatment is insufficient. Continuous deep oxidation of CB with effective Cl desorption is also a core issue successfully tackled through the steady Ru⁰↔Ru⁴⁺ circulation. This circulation was facilitated by the observed higher subnanometer Ru dispersion on {001}-TiO₂ than the other two noble metals that was supported by single atom stability DFT calculation. Nearly 88 degradation products in off-gas were detected, with Ru/{001}-TiO₂ producing the lowest polychlorinated benzene byproducts. An effective and sustainable CB degradation mechanism boosted by the cooperation of NaBH₄ enhanced active sites and Ru circulation was proposed accordingly. Insights gained from this study open a new avenue to the rational design of promising catalysts for the treatment of CVOCs.

Abatement of dichloromethane with high selectivity over defect-rich MOF-derived Ru/TiO2 catalysts

The regulation of oxygen vacancies and Ru species using metal-organic frameworks was synergically adopted in a rational design to upgrade Ru/TiO₂ catalysts, which are highly active for the catalytic oxidation of dichloromethane (DCM) with less undesired byproducts. In this work, Ru/M-TiO₂ and Ru/N-TiO₂ catalysts were synthesized by the pyrolysis of MIL-125 and NH₂-MIL-125 incorporated with Ru, the existence of Ru nanoclusters and nanoparticles was detected by XAFS, respectively, and the catalytic performance was analyzed comprehensively. Complete oxidation of DCM was obtained at ∼290 °C over Ru/M-TiO₂ and Ru/N-TiO₂ catalysts, while Ru/N-TiO₂ showed quite less monochloromethane (MCM) and higher CO₂ yields, and better dechlorination capacity in oxidation. The distinction comes down to that the easier desorption of chlorine could be achieved over Ru⁴⁺ which act as the main activated adsorption sites for DCM in Ru/N-TiO₂, compared to oxygen vacancies that serve as the main dissociation sites in Ru/M-TiO₂. Additionally, Ru/N-TiO₂ exhibited superior stability and excellent resilience in moisture. An in situ DRIFTS experiment further indicated the different DCM catalytic degradation process as well as the reaction mechanism over the as-prepared catalysts.

Lignosulfonate valorization into a Cu-containing magnetically recyclable photocatalyst for treating wastewater pollutants in aqueous media

This study presents an eco-friendly and economical process for preparing a magnetic copper complex conjugated to modified calcium lignosulfonate (LS) through a diamine (Fe₃O₄@LS@naphthalene-1,5-diamine@copper complex; FLN-Cu) as a green and novel catalyst. The prepared catalyst was characterized by Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), vibrating sample magnetometer (VSM), Brunauer-Emmett-Teller (BET), energy-dispersive X-ray spectroscopy (EDS), elemental mapping, inductively coupled plasma-optical emission spectrometry (ICP-OES) and field emission scanning electron microscopy (FESEM) techniques. The photocatalytic performance of the synthesized FLN-Cu catalyst was investigated by the degradation of aqueous solutions of dyes such as Rhodamine B (RhB), methylene blue (MB), and Congo red (CR) under UV irradiation. The dye degradation was followed by UV-Vis (ultraviolet-visible) spectrophotometry by measuring the changes in absorbance. The effects of different factors such as pH, contact time, photocatalyst dosage, and initial concentration of dye on the adsorption percentage were also investigated. Moreover, the catalyst showed high stability and could be readily separated from the reaction media using a magnet and reused five times without a remarkable loss of catalytic ability.

N-doped carbon-modified palladium catalysts with superior water resistant performance for the oxidative removal of toxic aromatics

The supported palladium catalysts perform well in the oxidative removal of hazardous aromatic hydrocarbons. However, water vapor can seriously deactivate the catalysts especially in the low-temperature regime. Hence, improving moisture resistance of the Pd-based catalysts is full of challenge in the removal of aromatics. Herein, we report a new type of Pd@NC/BN catalysts featured with nitrogen-doped carbon layers modified Pd supported on hexagonal boron nitride (h-BN), and the relationship between structure and water resistance of the catalysts. The results show that in the presence of 10 vol% H₂O in the feedstock, the Pd@NC/BN catalyst could effectively oxidize o-xylene (with an almost 87% removal efficiency), whereas o-xylene conversion declined from 69% to 20% over the conventional Pd/Al₂O₃ at a reaction temperature of 210 °C and a space velocity of 40,000 mL/(g h). The adsorption of H₂O was significantly inhibited on the nitrogen-doped carbon layers due to the hydrophobic nature. Meanwhile, the oxygen species active for o-xylene oxidation were not only from the adsorbed gas-phase oxygen but also from the new active oxygen (*OOH and *OH) species that were generated via the interaction of O₂ and H₂O in the presence of water in the feedstock. It is concluded that the reactive oxygen species that accelerated the activation and cleavage of C-H bonds significantly facilitated the conversion of key intermediate species (from benzaldehyde to benzoic acid), thus playing a decisive role in o-xylene oxidation. The present work provides a direction for developing the superior water resistance catalysts with hydrophobic nature and good water activation ability in the oxidative removal of volatile organic compounds.

Enhanced Water Resistance and Catalytic Performance of Ru/TiO2 by Regulating Brønsted Acid and Oxygen Vacancy for the Oxidative Removal of 1,2-Dichloroethane and Toluene

The compositions of volatile organic compounds (VOCs) under actual industrial conditions are often complex; especially, the interaction of intermediate products easily leads to more toxic emissions that are harmful to the atmospheric environment and human health. Herein, we report a comparative investigation on 1,2-dichloroethane (1,2-DCE) and (1,2-DCE + toluene) oxidation over the Ru/TiO₂, phosphotungstic acid (HPW)-modified Ru/TiO₂, and oxygen vacancy-rich Ru/TiO_x catalysts. The doping of HPW successfully introduced the 1,2-DCE adsorption sites to promote its oxidation and exhibited outstanding water resistance. For the mixed VOCs, Ru/HPW-TiO₂ promoted the preferential and superfluous adsorption of toluene and resulted in the inhibition of 1,2-DCE degradation. Therefore, HPW modification is a successful strategy in catalytic 1,2-DCE oxidation, but Brønsted acid sites tend to adsorb toluene in the mixed VOC oxidation. The Ru/TiO_x catalyst exhibited excellent activity and stability in the oxidation of mixed VOCs and could inhibit the generation of byproducts and Cl₂ compared with the Ru/HPW-TiO₂ catalyst. Compared with the Brønsted acid modification, the oxygen vacancy-rich catalysts are significantly suitable for the oxidation of multicomponent VOCs.

Single-Atom Ce-Modified α-Fe2O3 for Selective Catalytic Reduction of NO with NH3

A single-atom Ce-modified α-Fe₂O₃ catalyst (Fe_0.93Ce_0.07O_x catalyst with 7% atomic percentage of Ce) was synthesized by a citric acid-assisted sol-gel method, which exhibited excellent performance for selective catalytic reduction of NO_x with NH₃ (NH₃-SCR) over a wide operating temperature window. Remarkably, it maintained ∼93% NO conversion efficiency for 168 h in the presence of 200 ppm SO₂ and 5 vol % H₂O at 250 °C. The structural characterizations suggested that the introduction of Ce leads to the generation of local Fe-O-Ce sites in the FeO_x matrix. Furthermore, it is critical to maintain the atomic dispersion of the Ce species to maximize the amounts of Fe-O-Ce sites in the Ce-doped FeO_x catalyst. The formation of CeO₂ nanoparticles due to a high doping amount of Ce species leads to a decline in catalytic performance, indicating a size-dependent catalytic behavior. Density functional theory (DFT) calculation results indicate that the formation of oxygen vacancies in the Fe-O-Ce sites is more favorable than that in the Fe-O-Fe sites in the Ce-free α-Fe₂O₃ catalyst. The Fe-O-Ce sites can promote the oxidation of NO to NO₂ on the Fe_0.93Ce_0.07O_x catalyst and further facilitate the reduction of NO_x by NH₃. In addition, the decomposition of NH₄HSO₄ can occur at lower temperatures on the Fe_0.93Ce_0.07O_x catalyst containing atomically dispersed Ce species than on the α-Fe₂O₃ reference catalyst, resulting in the good SO₂/H₂O resistance ability in the NH₃-SCR reaction.

Recent Advances of Chlorinated Volatile Organic Compounds' Oxidation Catalyzed by Multiple Catalysts: Reasonable Adjustment of Acidity and Redox Properties

The severe hazard of chlorinated volatile organic compounds (CVOCs) to human health and the natural environment makes their abatement technology a key topic of global environmental research. Due to the existence of Cl, the byproducts of CVOCs in the catalytic combustion process are complex and toxic, and the possible generation of dioxin becomes a potential risk to the environment. Well-qualified CVOC catalysts should process favorable low-temperature catalytic oxidation ability, excellent selectivity, and good resistance to poisoning, which are governed by the reasonable adjustment of acidity and redox properties. This review overviews the application of different types of multicomponent catalysts, that is, supported noble metal catalysts, transition metal oxide/zeolite catalysts, composite transition metal oxide catalysts, and acid-modified catalysts, for CVOC degradation from the perspective of balance between acidity and redox properties. This review also highlights the synergistic degradation of CVOCs and NO_x from the perspective of acidity and redox properties. We expect this work to inspire and guide researchers from both the academic and industrial communities and help pave the way for breakthroughs in fundamental research and industrial applications in this field.

Selective Ru Adsorption on SnO2/CeO2 Mixed Oxides for Efficient Destruction of Multicomponent Volatile Organic Compounds: From Laboratory to Practical Possibility

Ru-based catalysts have been extensively employed for the catalytic destruction of chlorinated volatile organic compounds (VOCs), but their versatility for other routine VOCs' destruction has been less explored. Herein, we show that Ru-decorated SnO₂/CeO₂ mixed oxides can sustain H₂O and HCl poisonings and are endowed with extraordinary versatility for a wide range of VOCs' destruction. Selective adsorption of Ru on the cassiterite SnO₂ and CeO₂ nanorods through a Coulomb force can rationally tune the oxidation and dechlorination centers on decorated catalysts, where the epitaxial growth of RuO_x on top of SnO₂ is endowed with excellent dechlorination ability and that on CeO₂ is functional as an oxidation center; the latter could also activate H₂O to provide sufficient H protons for HCl formation. Our developed Ru/SnO₂/CeO₂ catalyst can steadily destruct mono-chlorobenzene, ortho-dichlorobenzene, trichloroethylene, dichloromethane, epichlorohydrin, N-hexane, ethyl acetate, toluene, and their mixtures at an optimum temperature of 300 °C, and its monolithic form is also functional at this temperature with few dioxins being detected in the off-gas. Our results imply that the Ru-decorated SnO₂/CeO₂ catalyst can meet the demands of regenerative catalytic oxidation for the treatment of a wide range of VOCs from industrial exhausts.

Engineering Platinum Catalysts via a Site-Isolation Strategy with Enhanced Chlorine Resistance for the Elimination of Multicomponent VOCs

Pt-based catalysts can be poisoned by the chlorine formed during the oxidation of multicomponent volatile organic compounds (VOCs) containing chlorinated VOCs. Improving the low-temperature chlorine resistance of catalysts is important for industrial applications, although it is yet challenging. We hereby demonstrate the essential catalytic roles of a bifunctional catalyst with an atomic-scale metal/oxide interface constructed by an intermetallic compound nanocrystal. Introducing trichloroethylene (TCE) exhibits a less negative effect on the catalytic activity of the bimetallic catalyst for o-xylene oxidation, and the partial deactivation caused by TCE addition is reversible, suggesting that the bimetallic, HCl-etched Pt₃Sn(E)/CeO₂ catalyst possesses much stronger chlorine resistance than the conventional Pt/CeO₂ catalyst. On the site-isolated Pt-Sn catalyst, the presence of aromatic hydrocarbon significantly inhibits the adsorption strength of TCE, resulting in excellent catalytic stability in the oxidation of the VOC mixture. Furthermore, the large amount of surface-adsorbed oxygen species generated on the electronegative Pt is highly effective for low-temperature C-Cl bond dissociation. The adjacent promoter (Sn-O) possesses the functionality of acid sites to provide sufficient protons for HCl formation over the bifunctional catalyst, which is considered critical to maintaining the reactivity of Pt by removing Cl and decreasing the polychlorinated byproducts.

Oxy-Anionic Doping: A New Strategy for Improving Selectivity of Ru/CeO2 with Synergetic Versatility and Thermal Stability for Catalytic Oxidation of Chlorinated Volatile Organic Compounds

Understanding the formation and inhibition of more toxic polychlorinated byproducts from the catalytic oxidation elimination of chlorinated volatile organic compounds (Cl-VOCs) and unveiling efficient strategies have been essential and challenging. Here, RuO_x supported on CePO₄-doped CeO₂ nanosheets (Ru/Pi-CeO₂) is designed for boosting catalytic oxidation for the removal of dichloromethane (DCM) as a representative Cl-VOC. The promoted acid strength/number and sintering resistance due to the doping of electron-rich and thermally stable CePO₄ are observed along with the undescended redox ability and the exposed multi-active sites, which demonstrates a high activity and durability of DCM oxidation (4000 mg/m³ and 15,000 mL/g·h, stable complete-oxidation at 300 °C), exceptional versatility for different Cl-VOCs, alkanes, aromatics, N-containing VOCs, CO and their multicomponent VOCs, and enhanced thermal stability. The suppression of polychlorinated byproducts is determined over Ru/Pi-CeO₂ and oxy-anionic S, V, Mo, Nb, or W doping CeO₂, thus the oxy-anionic doping strategy is proposed based on the quenching of the electron-rich oxy-anions on chlorine radicals. Moreover, the simple mechanical mixing with these oxy-anionic salts is also workable even for other catalysts such as Co, Sn, Mn, and noble metal-based catalysts. This work offers further insights into the inhibition of polychlorinated byproducts and contributes to the convenient manufacture of monolithic catalysts with superior chlorine-poisoning resistance for the catalytic oxidation of Cl-VOCs.

Emerging Pollutants in Wastewater, Advanced Oxidation Processes as an Alternative Treatment and Perspectives

Emerging pollutants are present in wastewaters treated by conventional processes. Due to water cycle interactions, these contaminants have been reported in groundwater, surface water, and drinking waters. Since conventional processes cannot guarantee their removal or biotransformation, it is necessary to study processes that comply with complete elimination. The current literature review was conducted to describe and provide an overview of the available information about the most significant groups of emerging pollutants that could potentially be found in the wastewater and the environment. In addition, it describes the main entry and distribution pathways of emerging contaminants into the environment through the water and wastewater cycle, as well as some of the potential effects they may cause to flora, fauna, and humans. Relevant information on the SARS-CoV-2 virus and its potential spread through wastewater is included. Furthermore, it also outlines some of the Advanced Oxidation Processes (AOPs) used for the total or partial emerging pollutants removal, emphasizing the reaction mechanisms and process parameters that need to be considered. As well, some biological processes that, although slow, are effective for the biotransformation of some emerging contaminants and can be used in combination with advanced oxidation processes.

Preparation of Highly Stable DUT-52 Materials and Adsorption of Dichromate Ions in Aqueous Solution

Highly stable DUT-52 materials were synthesized by the hydrothermal method and well-characterized by X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, and X-ray photoelectron spectroscopy (XPS). In order to systematically study the adsorption of dichromate ions in aqueous solution by the DUT-52 materials, a single factor experiment, kinetic experiment, thermodynamic experiment, competition ion experiment, and material regeneration experiment were designed. Based on the H-bond interaction between the dichromate ions and the H atoms of a NDC^2- ligand, the DUT-52 materials showed a maximum removal rate of 96.4% and a maximum adsorption capacity of 120.68 mg·g^-1 with excellent selective adsorption and material regeneration. In addition, the process of adsorption of dichromate ions by the DUT-52 materials is in accordance with the pseudo second-order kinetics and Langmuir models, and the adsorption mechanism and the important role of the H-bond interaction were reasonably explained using the XPS pattern and theoretical calculation. Accordingly, DUT-52 can be regarded as a multifunctional material for efficiently removing dichromate ions from the wastewater.

Biotemplate Fabrication of Hollow Tubular CexSr1-xTiO3 with Regulable Surface Acidity and Oxygen Mobility for Efficient Destruction of Chlorobenzene: Intrinsic Synergy Effect and Reaction Mechanism

Developing economic and applicable catalysts with elegant chlorine resistance and organic byproduct inhibition capability is of great significance for chlorinated volatile organic compounds (Cl-VOCs) eco-friendly purification. Here, ternary Ce_xSr_1-xTiO₃ catalysts with tunable surface acidity and oxygen species mobility were creatively fabricated using the hollow tubular-structured fruit hair of Platanus (FHP; a widespread greenery waste) as the scaffolding biotemplate. It is shown that the oxygen vacancy (O_v) triggered by the presence of Ce can optimize the synergy between the Lewis acid sites (LAS) and Brønsted acid sites (BAS). High concentration of O_v and BAS promotes the C-Cl cleavage of chlorobenzene (CB) and accelerates the desorption of Cl^• radicals as inorganic chlorine. Simultaneously, the strong electron transfer within Ti-Ce-Sr linkage increases the acidity of LAS, resulting in the superior reducibility of Ce_0.4Sr_0.6TiO₃ and facilitating the deep oxidation of dechlorination intermediates. Additionally, the spatial confinement of the tubular structure remarkably accelerates the CB flow rate and reduces the residence time of byproducts over the prepared catalysts. Owing to these, CB can be efficiently destructed over Ce_0.4Sr_0.6TiO₃ with selectivity of CO₂ and inorganic chlorine dramatically enhanced, respectively, approximately 16 and 21 times at 275 °C compared to those of pure SrTiO₃. The present work provides a feasible and promising strategy for engineering efficient catalysts for heterogeneous thermocatalytic reactions for industrial-scale Cl-CVOC destruction.

Characterization of Ziziphus lotus’ Activated Carbon and Evaluation of Its Adsorption Potential

This study aims to prepare activated carbon from an interesting biomaterial, corresponding to the cores of Ziziphus lotus, for the first time to the best of our knowledge, according to a manufacturing process based on its chemical and thermal activation. These cores were chemically activated by sulfuric acid for 24 h and then carbonized at 500°C for 2 hours. The obtained activated carbon was characterized by scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and Brunauer–Emmett–Teller (BET) analysis. The adsorption of methylene blue (MB) on the activated carbon was evaluated, by Langmuir and Freundlich models examination, in order to explain the adsorption efficiency in a systematic and scientific way. Moreover, pseudo-first-order and pseudo-second-order kinetic models were used to identify the mechanisms of this adsorption process. The characterization results showed an important porosity (pore sizes ranging from 10 to 45 µm), a surface structure having acid groups and carboxylic functions, and a specific surface of 749.6 m²/g. Results of the MB adsorption showed that this process is very fast as more than 80% of MB is adsorbed during the first 20 minutes. In addition, increasing the contact time and temperature improves the MB removal process efficiency. Moreover, this adsorption's kinetic modeling follows the pseudo-second-order model. Furthermore, data on the adsorption isotherm showed a maximum adsorption capacity of 14.493 mg/g and fit better with the Langmuir model. The thermodynamic parameters (∆G₀, ∆S₀, and ∆H₀) indicate that the adsorption process is endothermic and spontaneous. Therefore, Ziziphus lotus can be used as a low-cost available material to prepare a high-quality activated carbon having a promising potential in the wastewater treatment.

The efficiency of n- and p-type doping silicon carbide nanocage toward (NO2, SO2, and NH3) gases

The sensitivity of pristine silicon carbide nanocage Si12C12 and their doping with n-type (SiP–Si11C12) and p-type (CB–Si12C11) were investigated for NO2, SO2, and NH3 gases using density functional theory (DFT). The reactivity of nanocages was examined through adsorption energy, charge transfer, the density of states (DOS), thermodynamic parameters, frontier molecular orbitals, molecular electrostatic potential, and nonlinear optical properties. The results revealed that doping with p-type has excellent sensitivity for SO2, NO2, and NH3 gases compared with pristine and n-type doped nanocages.

Ultrasonic-assisted synthesis of zeolite/activated carbon@MnO2 composite as a novel adsorbent for treatment of wastewater containing methylene blue and brilliant blue

In this study, zeolite/activated carbon@MnO₂ composite was used as a novel adsorbent to eliminate methylene blue (MB) and brilliant blue (BB) dyes from aqueous media. To this end, activated carbon (AC) was produced by Ziziphus Spina-Christi leaves and then used to synthesize zeolite/AC@MnO₂ composite. Various analyses such as BET, SEM, EDX, Map, FTIR, and XRD were performed to determine the surface features of the above composite. BET analysis indicated that the aforementioned composite has a mesoporous structure. Also, the best conditions for the adsorption of MB and BB dyes were obtained at pH of 9 and 2, temperature of 25 °C, adsorbent dosage of 1 and 2 g/L, initial dye concentration of 10 mg/L, and contact time of 40 and 60 min, respectively. Under optimal conditions, the utmost removal efficiency of MB and BB dyes using the zeolite/AC@MnO₂ composite was 98.43% and 96.54%, respectively, indicating significant adsorption efficiencies. Moreover, the utmost adsorption capacity of MB and BB dyes was 67.56 and 66.22 mg/g, respectively. Furthermore, intraparticle and film diffusion mechanisms were very important in the adsorption process. Besides, thermodynamic and equilibrium studies indicated that the adsorption process is exothermic, physical, and spontaneous. Generally, the aforementioned composite has a significant adsorption capacity and can be a suitable adsorbent to eliminate cationic dyes from industrial effluents.

Density functional theory investigation of ozone gas uptake by a BeO nanoflake

Due to importance of the gas uptake topic in environment and energy issues, this work was performed for investigating ozone (Oz) gas uptake by means of a beryllium oxide (BeO) nanoflake. To this aim, density functional theory (DFT) calculations and the quantum theory of atoms in molecules (QTAIM) analysis were performed. The monolayer BeO nanoflake was decorated by a HEME-like N4Fe region to prepare an interacting region towards the Oz uptake. Accordingly, three models were optimized based on configurations of Oz molecule relaxation at the BeO surface, in which two types of O ... Fe and O ... N interactions were observed. In this case, Oz3@BeO model was involved with two mentioned types of interactions and three occurred interaction between Oz and BeO making it as the strongest bimolecular formation model of Oz@BeO. Moreover, electronic molecular orbital features indicated that the models formations could be also related to sensor functions by variations of electric conductivity because of Oz gas uptake. As a consequence, the investigated BeO nanoflake of this work was proposed for employing in Oz gas uptake for different purposes.

A molecular modeling on the boron trichloride gas detection by S- and Cr-doped graphyne

Here, we scrutinize the adsorption of boron trichloride (BCl₃) on pure, S-doped, and Cr-doped graphyne by means of density functional theory (DFT) calculations. BCl₃ interacts weakly with pure graphyne, so it cannot be employed as a sensor. Despite the strengthening of interaction through S-doping, we cannot still employ the S-doped sheet as a sensor. Nevertheless, there is a considerable increase in the sensitivity and reactivity of the sheet through substituting the transition metal Cr for the C. There is a reduction in the HOMO-LUMO gap of Cr-doped graphyne from 2.18 to 1.38 eV when BCl₃ is adsorbed, thereby increasing the electrical conductivity to a great extent. Hence, it is possible to convert the considerable change in conductivity into an electronic signal, which demonstrates the encouraging nature of Cr-doped graphyne as a sensor to detect BCl₃. Additionally, the adsorption process reduces the work function of graphyne to a great extent, which demonstrates that we can also employ it as a work function-type sensor for detecting BCl₃.