Synthesis of Fe3O4/Polyacrylonitrile Composite Electrospun Nanofiber Mat for Effective Adsorption of Tetracycline

Characterization and optimization of magnetic molecularly imprinted nanofibers for determination of sunitinib in human serum and capsule samples

This article reports a spectrofluorometric method for the determination of sunitinib (STB) drug based on molecularly imprinted nanofibers fabricated by the electrospinning method and modified by magnetic nanoparticles as sorbent. The characterization of magnetic molecularly imprinted nanofibers (MMINs) was carried out using X-ray diffraction (XRD), scanning electron microscope (SEM), and transmission electron microscopy (TEM), which confirmed the successful synthesis of MMINs with well-distributed magnetite nanoparticles. Drug adsorption and desorption were optimized and important parameters such as sample pH, nanofiber mass, adsorption and desorption time, eluent solvent and sample volume were analyzed. The results demonstrated that the MMINs act as a selective sorbent for STB and can be readily collected through an external magnetic field. Methanol was used as the best eluent solvent for STB desorption from MNIN. A linear correlation was observed between the STB concentrations and fluorescence intensities in the range of 0.01-15.0 mg L-1. The detection limit for this method was 0.002 mg L-1. The relative standard deviation (RSD) of 2.6 % for 1.0 mg L-1 and 1.1 % for 10 mg L-1 of STB (n = 3) were obtained, which indicates that the developed method is precise in determining STB. Human serum and capsule analysis show the applicability of the proposed sensor for real samples.

Design and optimization of a cost-effective paper-based voltammetric sensor for the determination of trinitrotoluene (TNT) utilizing cysteamine-linked Fe3O4 @Au nanocomposite

This paper presents the development and optimization of a cost-effective paper electrochemical sensor for the detection of TNT using Fe3O4-Au core-shell nanoparticles modified with cysteamine (Fe3O4@Au/CA). The sensor was constructed by modifying a graphite paste with the aforementioned nanoparticles, which facilitated the formation of a Meisenheimer complex between cysteamine and TNT as an electron donor and an electron acceptor, respectively. The central composite design was employed to optimize four key parameters pH, modifier percentage, contact time, and buffer type to enhance the performance of the sensor. The detection limit was found to be 0.5 nM of TNT, while the linear range of the electrode response spanned from 0.002 μM to 10 μM. The simplicity and low cost of the sensor make it highly attractive for practical applications, particularly in scenarios where rapid and on-site TNT detection is required.

Efficient Cr(VI) remediation by electrospun composite porous nanofibers incorporating biomass with metal oxides and metal-organic framework

To develop a highly efficient adsorbent to remediate and remove hexavalent chromium ions (Cr(VI)) from polluted water, cellulose acetate (CA) and chitosan (CS), along with metal oxides (titanium dioxide (TiO2) and ferroferric oxide (Fe3O4)), and a zirconium-based metal-organic framework (UiO-66) were used to fabricate the composite porous nanofiber membranes through electrospinning. The adsorption performance, influencing factors, adsorption kinetics and isotherms of composite nanofiber membranes were comprehensively investigated. The multi-layer membrane with interpenetrating nanofibers and surface functional groups enhanced the natural physical adsorption and provided potential chemical sites. The thermal stability was improved by introducing TiO2 and UiO-66. CA/CS/UiO-66 exhibited the highest adsorption capacity (118.81 mg g-1) and removal rate (60.76%), which were twice higher than those of the control. The correlation coefficients (R2) of all the composite nanofibers regressed by the Langmuir model were significantly higher than those by the Freundlich model. The pseudo-first-order kinetic curve of CA/CS composite nanofibers showed the highest R2 (0.973), demonstrating that the whole adsorption process involved a combination of strong physical adsorption and weak chemical adsorption by the amino groups of CS. However, the R2 values of the pseudo-second-order kinetic model increased after incorporating TiO2, Fe3O4, and UiO-66 into the CA/CS composite nanofiber membranes since an enhanced chemical reaction with Cr (VI) occured during the adsorption.

Facile low-temperature supercritical carbonization method to prepare high-loading nickel single atom catalysts for efficient photodegradation of tetracycline

Environmental photocatalysis is a promising technology for treating antibiotics in wastewater. In this study, a supercritical carbonization method was developed to synthesize a single-atom photocatalyst with a high loading of Ni (above 5 wt.%) anchored on a carbon-nitrogen-silicate substrate for the efficient photodegradation of a ubiquitous environmental contaminant of tetracycline (TC). The photocatalyst was prepared from an easily obtained metal-biopolymer-inorganic supramolecular hydrogel, followed by supercritical drying and carbonization treatment. The low-temperature (300°C) supercritical ethanol treatment prevents the excessive structural degradation of hydrogel and greatly reduces the metal clustering and aggregation, which contributed to the high Ni loading. Atomic characterizations confirmed that Ni was present at isolated sites and stabilized by Ni-N and Ni-O bonds in a Ni-(N/O)6C/SiC configuration. A 5% Ni-C-Si catalyst, which performed the best among the studied catalysts, exhibited a wide visible light response with a narrow bandgap of 1.45 eV that could efficiently and repeatedly catalyze the oxidation of TC with a conversion rate of almost 100% within 40 min. The reactive species trapping experiments and electron spin resonance (ESR) tests demonstrated that the h+, and ·O2- were mainly responsible for TC degradation. The TC degradation mechanism and possible reaction pathways were provided also. Overall, this study proposed a novel strategy to synthesize a high metal loading single-atom photocatalyst that can efficiently remove TC with high concentrations, and this strategy might be extended for synthesis of other carbon-based single-atom catalysts with valuable properties.

Construction of urchin-like core-shell Fe/Fe2O3@UiO-66 hybrid for effective tetracycline reduction and photocatalytic oxidation

Although Fe/Fe2O3 has potential application compared with nanoscale zero-valent iron (nZVI), its smooth structure largely limits the catalytic performance. To address this challenge, we innovatively constructed highly efficient composite Fe/Fe2O3@UiO-66 via employing an urchin-like core-shell structure of Fe/Fe2O3 onto UiO-66 through a facile ion exchange precipitation method without inert gas protection. The characterization results show the urchin-like core-shell configuration can extend the life span of Fe0 and produce more active sites. Besides, the absorption spectrum is broadened by Fe2O3 which has narrow band gap and the high-efficiency separation of photogenerated electron-hole pairs is obtained with the load of Fe/Fe2O3. Moreover, Two-parameter pseudo-first-order decay model fits well with the reduction and adsorption of composites in the dark reaction, and a plausible pathway for tetracycline (TC) degradation is also proposed. The findings of this research provide a promising method for promoting the catalytic properties of MOF-based materials and Fe/Fe2O3.

Stimulating anaerobic digestion to degrade recalcitrant organic pollutants: Potential role of conductive materials-led direct interspecies electron transfer

This review aims to provide a comprehensive understanding of the potential of CMs-dominated DIET in the degradation of recalcitrant organic pollutants in AD. The review covers the mechanisms and efficiencies of recalcitrant organic pollutant degradation by CMs-dominated DIET, the comparison of degradation pathways between DIET and chemical treatment, recent insights on DIET-enhanced degradation, and the evaluation of the potential and future development of CMs-dominated DIET. The review emphasizes the importance of coupled syntrophic microorganisms, electron flux, and physicochemical properties of CMs in enhancing the degradation performance of AD. Additionally, it highlights the advantages of DIET-led syntrophic metabolism over traditional oxidation technologies in terms of environmental friendliness and efficiency. Finally, the review acknowledges the potential risks associated with introducing CMs into AD systems and provides guidance for waste treatment and energy recovery.

Simple ultrasonic integration of shapeable, rebuildable, and multifunctional MIL-53(Fe)@cellulose composite for remediation of aqueous contaminants

Metal-organic frames (MOFs) have been recognized as one of the best candidates in the remediation of aqueous contaminants, while the fragile powder shape restricts the practical implementation. In this work, a shapeable, rebuildable, and multifunctional MOF composite (MIL-53@CF) was prepared from MIL-53 (Fe) and cellulose fiber (CF) using a simple ultrasonic method for adsorption and photocatalytic degradation of organic pollutants in wastewater. The results showed MIL-53(Fe) crystals were uniformly growth on CF surfaces and bonded with surface nanofibrils of CF through physical crosslinking and hydrogen bonding. Because of the high bonding strength, the MIL-53@CF composite exhibited an excellent compressive strength (3.53 MPa). More importantly, the MIL-53@CF composite was rebuildable through mechanical destruction followed by re-ultrasonication, suggesting the excellent reusability of MIL-53@CF for water remediation. The MIL-53@CF composite also had high adsorption capacities for methyl orange (884.6 mg·g-1), methylene blue (198.3 mg·g-1), and tetracycline (106.4 mg·g-1). MIL-53@CF composite could degrade TC through photocatalysis. The photocatalytic degradation mechanism was attributed to the Fe(II)/Fe(III) transform cycle reaction of MIL-53 crystal located on MIL-53@CF. Furthermore, the mechanical property and remoldability of MIL-53@CF composite increased its practicability. Comprehensively, MIL-53@CF composite provided a possible strategy to practically apply MOF in the remediation of aqueous contaminants.

Efficient adsorptive removal of aminoglycoside antibiotics from environmental water

Aminoglycoside antibiotics (AGs) in environmental water are emerging pollutants that must be removed to protect human health and the ecosystem. However, removing AGs from environmental water remains a technical challenge due to high polarity, stronger hydrophilicity and unique characteristics of polycation. Herein, a thermal-crosslinked polyvinyl alcohol electrospun nanofiber membrane (T-PVA NFsM) is synthesized and firstly leveraged as the adsorptive removal of AGs from environmental water. The thermal crosslinking strategy is demonstrated to enhance both the water resistance and hydrophilicity of T-PVA NFsM, thereby effectively interacting with AGs with high stability. Experimental characterizations and analog calculations indicate that T-PVA NFsM utilizes multiple adsorption mechanisms, including electrostatic and hydrogen bonding interactions with AGs. As a result, the material achieves 91.09%-100% adsorption efficiencies and a maximum adsorption capacity of 110.35 mg g^-1 in less than 30 min. Furthermore, the adsorption kinetics follow the pseudo-second-order model. After eight consecutive adsorption-desorption cycles, T-PVA NFsM with a simplified recycling process maintains a sustainable adsorption capability. Compared with other forms of adsorption materials, T-PVA NFsM has significant advantages such as less consumption of adsorbent, high adsorption efficiency and fast removal speed. Therefore, T-PVA NFsM-based adsorptive removal holds promise for eliminating AGs from environmental water.

Research progress on the magnetite nanoparticles in the fields of water pollution control and detection

Magnetite nanoparticles (MNPs) have shown increasing application in the fields of water pollution control and detection due to their perfect combination of interfacial functionalities and physicochemical properties, such as surface interface adsorption, (synergistic) reduction, catalytic oxidation, and electrical chemistry. This review presents the research advances in the synthesis and modification methods of MNPs in recent years, systematically summarizes the performances of MNPs and their modified materials in terms of three technical systems, including single decontamination system, coupled reaction system, and electrochemical system. In addition, the progress of the key roles played by MNPs in adsorption, reduction, catalytic oxidative degradation and their coupling with zero-valent iron for the reduction of pollutants are described. Moreover, the application prospect of MNPs-based electrochemical working electrodes for detecting micro-pollutants in water were also discussed in detail. This review addresses that the construction of MNPs-based systems for water pollution control and detection should be adapted to the natures of the target pollutants in water. Finally, the following research directions of MNPs and their remaining challenges are outlooked. In general, this review will inspire MNPs researchers in different fields for effective control and detection of a variety of contaminants in water.

Mesoporous Activated Biochar from Crab Shell with Enhanced Adsorption Performance for Tetracycline

In this study, three mesoporous-activated crab shell biochars were prepared by carbonation and chemical activation with KOH (K-CSB), H₃PO₄ (P-CSB), and KMnO₄ (M-CSB) to evaluate their tetracycline (TC) adsorption capacities. Characterization by SEM and a porosity analysis revealed that the K-CSB, P-CSB, and M-CSB possessed a puffy, mesoporous structure, with K-CSB exhibiting a larger specific surface area (1738 m²/g). FT-IR analysis revealed that abundant, surface ox-containing functional groups possessed by K-CSB, P-CSB, and M-CSB, such as -OH, C-O, and C=O, enhanced adsorption for TC, thereby enhancing their adsorption efficiency for TC. The maximum TC adsorption capacities of the K-CSB, P-CSB, and M-CSB were 380.92, 331.53, and 281.38 mg/g, respectively. The adsorption isotherms and kinetics data of the three TC adsorbents fit the Langmuir and pseudo-second-order model. The adsorption mechanism involved aperture filling, hydrogen bonding, electrostatic action, π-π EDA action, and complexation. As a low-cost and highly effective adsorbent for antibiotic wastewater treatment, activated crab shell biochar has enormous application potential.

Controlling the physical properties of polyacrylonitrile by strontium hexaferrite nanoparticles

The formulation of polymer with embedded magnetic nanoparticles results in promising nanocomposites for smart and analytical applications. Nanocomposites containing polyacrylonitrile (PAN) and different mass contents of strontium hexaferrite (SFO) were prepared using the casting method. The nanocomposite samples were characterized by using different techniques such as field-emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, differential scanning calorimetry, and thermogravimetric analysis. Dielectric investigations of SFO/PAN nanocomposites showed that the permittivity and conductivity are considerably enhanced as the content of SFO increased. Optical properties revealed that the absorption and transmittance spectra were significantly affected by adding SFO nanoparticles to the PNA polymer matrix. To investigate the magnetic properties of the nanocomposite samples, the vibrating sample magnetometer was used. The magnetic hysteresis loops illustrated the ferromagnetic nature of SFO/PAN nanocomposites. Different magnetic parameters were given, and they depend on the content of PAN in the nanocomposites.

Systematic and Bibliometric Analysis of Magnetite Nanoparticles and Their Applications in (Biomedical) Research

Recent reports show air pollutant magnetite nanoparticles (MNPs) in the brains of people with Alzheimer's disease (AD). Considering various field applications of MNPs because of developments in nanotechnology, the aim of this study is to identify major trends and data gaps in research on magnetite to allow for relevant environmental and health risk assessment. Herein, a bibliometric and systematic analysis of the published magnetite literature (n = 31 567) between 1990 to 2020 is completed. Following appraisal, publications (n = 244) are grouped into four time periods with the main research theme identified for each as 1990-1997 "oxides," 1998-2005 "ferric oxide," 2006-2013 "pathology," and 2014-2020 "animal model." Magnetite formation and catalytic activity dominate the first two time periods, with the last two focusing on the exploitation of nanoparticle engineering. Japan and China have the highest number of citations for articles published. Longitudinal analysis indicates that magnetite research for the past 30 years shifted from environmental and industrial applications, to biomedical and its potential toxic effects. Therefore, whilst this study presents the research profile of different countries, the development in research on MNPs, it also reveals that further studies on the effects of MNPs on human health is much needed.

Recent advances and remaining barriers to the development of electrospun nanofiber and nanofiber composites for point-of-use and point-of-entry water treatment systems

In this review, we focus on electrospun nanofibers as a promising material alternative for the niche application of decentralized, point-of-use (POU) and point-of-entry (POE) water treatment systems. We focus our review on prior work with various formulations of electrospun materials, including nanofibers of carbon, pure metal oxides, functionalized polymers, and polymer-metal oxide composites, that exhibit analogous performance to media (e.g., activated carbon, ion exchange resins) commonly used in commercially available, certified POU/POE devices for contaminants including organic pollutants, metals (e.g., lead) and persistent oxyanions (e.g., nitrate). We then analyze the relevant strengths and remaining research and development opportunities of the relevant literature based on an evaluation framework that considers (i) performance comparison to commercial analogs; (ii) appropriate pollutant targets for POU/POE applications; (iii) testing in flow-through systems consistent with POU/POE applications; (iv) consideration of water quality effects; and (v) evaluation of material strength and longevity. We also identify several emerging issues in decentralized water treatment where nanofiber-based POU/POE devices could help meet existing needs including their use for treatment of uranium, disinfection, and in electrochemical treatment systems. To date, research has demonstrated promising material performance toward relevant targets for POU/POE applications, using appropriate aquatic matrices and considering material stability. To fully realize their promise as an emerging treatment technology, our analysis of the available literature reveals the need for more work that benchmarks nanofiber performance against established commercial analogs, as well as fabrication and performance validation at scales and under conditions simulating POU/POE water treatment.

Ofloxacin Removal from Aqueous Media by Means of Magnetoactive Electrospun Fibrous Adsorbents

Functionalized electrospun polymer microfibrous membranes were fabricated by electrospinning and further surface-functionalized with magnetic iron oxide (Fe_xO_y) nanoparticles to yield magnetoactive nanocomposite fibrous adsorbents. The latter were characterized in respect to their morphology, mechanical properties and magnetic properties while they were further evaluated as substrates for removing Ofloxacin (OFL) from synthetic aqueous media and secondary urban wastewater (UWW) under varying physicochemical parameters, including the concentration of the pharmaceutical pollutant, the solution pH and the membranes' magnetic content. The magnetic-functionalized fibrous adsorbents demonstrated significantly enhanced adsorption efficacy in comparison to their non-functionalized fibrous analogues while their magnetic properties enabled their magnetic recovery and regeneration.

Magnetic MXene-NH2 decorated with persimmon tannin for highly efficient elimination of U(VI) and Cr(VI) from aquatic environment

Herein, a magnetic MXenes based composite (Fe₃O₄@Ti₃C₂-NH₂-PT) was constructed by loading Fe₃O₄ nano-particles into the interlamellar spacing of persimmon tannin-functionalized Ti₃C₂-NH₂. The structure, morphology and physicochemical properties of the as-prepared adsorbents were probed by advanced spectroscopy techniques, while the impact of various experimental conditions like pH values, amount of adsorbent and contact time on the removal trend were examined by batch experiments. The elimination results revealed that Fe₃O₄@Ti₃C₂-NH₂-PT could be applied in a wide range of initial concentrations, and exhibited outstanding removal efficiency for U(VI) (104.9 mg/g, pH = 5.0) and Cr(VI) (83.8 mg/g, pH = 2.0). Meanwhile, the adsorption process was described well with the Langmuir isotherm and Pseudo-second-order kinetics models, which indicated that the monolayer chemical adsorption occurred during elimination of the two contaminants. The spectral analysis results manifested that elimination of U(VI) followed an inner-sphere configuration, whereas uptake of Cr(VI) was determined by electrostatic interaction and adsorption-reduction process. This work opened a new opportunity in designing MXenes based adsorbents in the application for environmental remediation.

Design of composite nanosupports and applications thereof in enzyme immobilization: A review

Enzyme immobilization techniques have developed dramatically over the past several decades. Support materials are key in shaping the function of a specific immobilized enzyme. Although they have large specific surface areas and functional active sites, single-component nanomaterials and their surface chemical modification derivatives struggle to meet increasing demand. Thus, composite materials, compounds of two or more materials, have been developed and applied in efficient immobilization through advances in materials science. More methods have been developed and employed to design composite nanomaterials in recent years. These novel composite nanomaterials often show superior physical, chemical, and biological performance as supports in enzyme immobilization, among other applications. In this review, immobilization techniques and their supports are stated first and methods to design and fabricate composite nanomaterials as nanosupports are also shown in the following section. Applications of composite nanosupports in laccase immobilization are discussed as models in the later sections of the paper. This review is intended to help readers gain insight into the design principles of composite nanomaterials for immobilization supports.

Fast cost-effective synthesis of metal ions/biopolymer/silica composites by supramolecular hydrogels crosslink with superior tetracycline sorption performance

In this study, a fast one-pot method was developed for the preparation of Cu/CS/Si ternary composites, which can efficiently remove antibiotic tetracycline from aqueous solutions. Our results demonstrated that the Cu and its content in the composites played a significant role in determining the physical properties and internal morphology of the Cu/CS/Si composites, which subsequently affected the efficiency of the composites for the sorptive removal of tetracycline. Among the studied composites, Cu₃-CS₂-Si materials had the largest sorption capacity for tetracycline (1076.7 mg/g) with a fast sorption kinetics (>99% in 30 min) under a broad working pH range (5-10). The results from the batch sorption experiments, together with spectroscopic and microscopic analyses, collectively indicated that Cu-tetracycline inner-sphere surface complexation through Cu-O bond was responsible for the tetracycline sorption on Cu₃-CS₂-Si. In addition, the Cu₃-CS₂-Si showed an excellent reusability in removing tetracycline. The desired sorption and reuse properties, coupled with the facile and cost-effective synthesis method, indicated that Cu/CS/Si composites have a promising potential for the efficient removal of tetracycline from contaminated solutions.

Adsorption and photocatalysis removal of arsenite, arsenate, and hexavalent chromium in water by the carbonized composite of manganese-crosslinked sodium alginate

The preparation of easily synthesized and cheap composite materials for the efficient removal of toxic oxoanions still remains challenging in sewage treatment. Herein, a new carbonized manganese-crosslinked sodium alginate (Mn/SA-C) was fabricated for the removal of arsenite (As(III)), arsenate (As(V)) and hexavalent chromium (Cr(VI)) in water. The results indicated that the Mn/SA-C pretreated with MnSO₄ solution (Mn/SA-C-S) exhibited a rapid adsorption toward As(III) and As(V) with the removal efficiency of >98% within 10 min, and had a high adsorption capacity toward As(III), As(V), and Cr(VI) with the maximum value of 189.29, 193.29, and 104.50 mg/g based on the Langmuir model, respectively. The removal efficiency of As(III), As(V), and Cr(VI) could be further significantly enhanced by coupling a photocatalytic process. For example, the time in which >98% of Cr(VI) (10 mg/L) was removed dramatically shortened from 360 min (adsorption) to 45 min (adsorption-photocatalysis), and the removal efficiency of As(III) increased by ∼10% within initial 5 min. This was primarily attributed to the Mn-catalyzed production of the photocatalytic excitons for Cr(VI) reduction, and the superoxide (•O₂^-) and hydroxyl (•OH) radicals for As(III) oxidation. The adsorption removal of arsenic (As) was primarily ascribed to surface complexation with MnO and precipitation by MnS₂, and oxidative adsorption because of Mn valence cycle. The removal mechanisms of Cr(VI) mainly contained reduction by MnO and MnS₂, complexation with MnO and carboxyl/hydroxyl groups as well as Cr(OH)₃ precipitation. Our research provides a promising Mn/SA-C-S material for rapid and efficient removal of As(III), As(V), and Cr(VI) in contaminated water through an adsorption-photocatalysis synergistic strategy.

Magnetic Adsorbents for Wastewater Treatment: Advancements in Their Synthesis Methods

The remediation of water streams, polluted by various substances, is important for realizing a sustainable future. Magnetic adsorbents are promising materials for wastewater treatment. Although numerous techniques have been developed for the preparation of magnetic adsorbents, with effective adsorption performance, reviews that focus on the synthesis methods of magnetic adsorbents for wastewater treatment and their material structures have not been reported. In this review, advancements in the synthesis methods of magnetic adsorbents for the removal of substances from water streams has been comprehensively summarized and discussed. Generally, the synthesis methods are categorized into five groups, as follows: direct use of magnetic particles as adsorbents, attachment of pre-prepared adsorbents and pre-prepared magnetic particles, synthesis of magnetic particles on pre-prepared adsorbents, synthesis of adsorbents on preprepared magnetic particles, and co-synthesis of adsorbents and magnetic particles. The main improvements in the advanced methods involved making the conventional synthesis a less energy intensive, more efficient, and simpler process, while maintaining or increasing the adsorption performance. The key challenges, such as the enhancement of the adsorption performance of materials and the design of sophisticated material structures, are discussed as well.

Removal of chlortetracycline from water using spent tea leaves-based biochar as adsorption-enhanced persulfate activator

Antibiotic compounds have caused serious environmental concerns. In this study, we developed an effective technology for treatment of chlortetracycline (CTC), a widely used antibiotic compound. A natural heteroatom-doped spent tea leaves-based biochar (STLB) with excellent adsorption and catalytic property was prepared by simple thermal treatment. An adsorption-promoted persulfate-based advanced oxidation process (PS-AOP) using STLB was studied for CTC removal. The results showed that the as-prepared STLB presented favorable adsorption affinity towards CTC with the maximum adsorption capacity of 627 mg g^-1. Meanwhile, CTC enriched on the surface of STLB was good for in-situ decomposition of CTC and nearly 97.4 % of CTC was removed within 30 min of pre-adsorption and 60 min of subsequent degradation. The STLB had excellent recyclability and wide pH tolerance range of 3.0-9.0 in combined pre-adsorption and PS-AOP. Reactive oxygen species analysis confirmed that CTC degradation was mainly due to non-radical (singlet oxygen, ¹O₂) and radicals (SO₄^- and OH). This study suggests that STLB is a promising adsorption-enhanced PS activator for the treatment of refractory wastewater and also provides a strategy of waste control by spent tea leaves.

Fish scale-based biochar with defined pore size and ultrahigh specific surface area for highly efficient adsorption of ciprofloxacin

A fish scale-based porous activated biochar with defined pore size (DPBC) was fabricated by a one-step calcination and activation method. The DPBC possessed an ultrahigh specific surface area of 3370 m² g^-1 and its pore diameter centered at 1.49 nm which fits into the ciprofloxacin (CIP) molecular dimension, making it an ideal adsorbent for CIP adsorption due to the molecular pore-filling effect. The maximum Langmuir monolayer adsorption capacity of DPBC for CIP was higher than 1000 mg g^-1 and the equilibrium time was less than 4 h, superior to most adsorbents reported in literature. Thermodynamic analysis indicated the adsorption process was spontaneous and endothermic. Notably, fixed-bed experiments showed an encouraging adsorption performance towards CIP, with a high saturated dynamic adsorption capacity of 880.3 mg g^-1. Both Thomas and Yoon-Nelson models predict the fixed-bed column adsorption performance well. Hydrophobic effect, π-π interaction, π-π EDA, cation exchange, hydrogen bonding formation, pore filling effect, electrostatic and cation-π interaction involved in the CIP adsorption on the DPBC.

Enhanced sequestration of tetracycline by Mn(II) encapsulated mesoporous silica nanoparticles: Synergistic sorption and mechanism

A novel Mn(II) encapsulated mesoporous silica nanoparticles (Mn-MSNs) was developed for efficiently removing antibiotic tetracycline from aqueous solutions. The material has a well-ordered, hexagonal mesopore structure with a large specific surface area (720 m²/g) and maximum sorption capacity (229 mg/g) that is about an order of magnitude higher than that of mesoporous silica nanoparticles without Mn-encapsulated, or encapsulated with other transition metal cations Fe³⁺ and Cu²⁺. Sorption results showed that the materials can sequestrate tetracycline within a large concentration range (5 μg/L-450 mg/L). Batch sorption experiment, spectroscopic analysis and density functional theory calculation collectively indicated that Mn-O complexation was the dominant mechanism for the tetracycline sorption. Electrostatic attraction and cation-π interaction also contributed to tetracycline sorption with their contribution levels varying with pH in a synergetic way with the Mn-O complexation. The Mn(II) encapsulated MSNs exhibited a good regeneration property over five repeated sorption-desorption cycles, demonstrating its promising potential in the cost-effective applications of sequestrating tetracycline from wastewater, drinking water, and contaminated solutions.

Effect of UVC and UVA Photocatalytic Processes on Tetracycline Removal Using CuS-Coated Magnetic Activated Carbon Nanocomposite: A Comparative Study

In this study, we synthesized a novel MAC nanocomposite using almond’s green hull coated with CuS. The whole set of experiments have been conducted inside a batch (discontinuous reactor system) at room temperature. The effectiveness of different parameters in tetracycline removal pH (3, 5, 7, and 9), pollutant concentration (5–100 mg/L), nanocomposite dosage (0.025–1 g/L), and contact time (5–60 min) using newly synthesized nanocomposite were investigated. Based on the results, in the optimal conditions of pH = 9, nanocomposite dosage of 1 g/L, pollutant concentration of 20 mg/L, contact time of 60 min, and room temperature, 95% removal efficiency was obtained. In MAC/CuS/UV_C process, the removal of COD and TOC were 76.89% and 566.84% respectively meanwhile, these values in MAC/CuS/UV_A process were 74.19% and 62.11%, respectively. The results of nanocomposite stability and magnetic recovery illustrated that the removal efficiency was reduced by 1.5% in the presence of UV_C and 5% in the presence of UV_A lights during all six cycles. Therefore, this nanocomposite was highly capable of recycling and reuse. It can be concluded that considering the high potential of the synthesized nanocomposite, the photocatalytic efficiency of the MAC/CuS/UV_C process in tetracycline synthesis was higher than MAC/CuS/UV_A process.

Hierarchical Photothermal Fabrics with Low Evaporation Enthalpy as Heliotropic Evaporators for Efficient, Continuous, Salt-Free Desalination

Solar-driven seawater evaporation is usually achieved on floating evaporators, but the performances are substantially limited by high evaporation enthalpy, solid salt crystallization, and reduced evaporation due to inclined sunlight. To solve these problems, we fabricated hierarchical polyacrylonitrile@copper sulfide (PAN@CuS) fabrics and proposed a prototype of heliotropic evaporator. Hierarchical PAN@CuS fabrics show significantly decreased water-evaporation enthalpy (1956.32 kJ kg^-1, 40 °C), compared with that of pure water (2406.17 kJ kg^-1, 40 °C), because of the disorganization of the hydrogen bonds at the CuS interfaces. Based on this fabric, a heliotropic evaporation model was developed, where seawater slowly flows from high to low in the fabric. Under solar irradiation (1.0 kW m^-2), this model exhibits a high-rate evaporation (∼2.27 kg m^-2 h^-1) and saturated brine production without solid salt crystallization. In particular, under inclined sunlight (angle range: from -90° to +90°), the heliotropic model retains an almost unchanged solar evaporation rate, whereas the floating model shows severe evaporation reduction (83.9%). Therefore, our study provides a strategy for reducing the evaporation enthalpy, maximally utilizing solar energy and continuous salt-free desalination.

Phosphate Adsorption from Aqueous Solution Using Electrospun Cellulose Acetate Nanofiber Membrane Modified with Graphene Oxide/Sodium Dodecyl Sulphate

Eutrophication and water pollution caused by a high concentration of phosphate are two concerning issues that affect water quality worldwide. A novel cellulose-based adsorbent, cellulose acetate/graphene oxide/sodium dodecyl sulphate (CA/GO/SDS), was developed for water treatment. A 13% CA solution in a mixture of acetone:dimethylacetamide (2:1) has been electrospun and complexed with a GO/SDS solution. The field emission scanning electron microscope (FESEM) showed that the CA membrane was pure white, while the CA/GO/SDS membrane was not as white as CA and its colour became darker as the GO content increased. The process of phosphate removal from the solutions was found to be aided by the hydroxyl groups on the surface of the CA modified with GO/SDS, as shown by infrared spectroscopy. An optimization condition for the adsorption process was studied by varying pH, immersion time, and the mass of the membrane. The experimental results from phosphate adsorption showed that CA/GO/SDS had an excellent pH adaptability, with an optimum pH of 7, and maximum removal (>87.0%) was observed with a membrane mass of 0.05 g at an initial concentration of 25 mg L^-1. A kinetic study revealed that 180 min of contact time could adsorb about 87.2% of phosphate onto the CA/GO/SDS membrane. A typical pseudo-second-order kinetic model successfully portrayed the kinetic sorption of phosphate, and the adsorption equilibrium data were well-correlated with the Langmuir adsorption model, suggesting the monolayer coverage of adsorbed molecules.

Electrospun chitosan oligosaccharide/polycaprolactone nanofibers loaded with wound-healing compounds of Rutin and Quercetin as antibacterial dressings

Burn injury has posed devastating burdens on the public health due to its inevitable damage to the skin structure resulting in the increased risk of infection. Therefore, it is highly demanding to develop efficacious antibacterial wound-healing dressing. Despite the favourable wound-healing activities, the curative efficacy of phytochemical compounds of quercetin (Qe) and its derivatives is limited by their poor water solubility. Here, we have fabricated a novel electrospun nanofiber membrane (ENM) consisting of polycaprolactone (PCL), chitosan oligosaccharides (COS), and Qe/Rutin (Ru) as the potential bioactive dressing for wound healing. The incorporation of chitosan oligosaccharides (COSs) in the PCL scaffold at the optimized molar ratio not only contributed to the improved hydrophilicity and water absorption performance of the ENM but effectively increased the specific surface area of the formed nanofibers. In particular, the antioxidant and antibacterial activities of the Qe/rutin-loaded nanofiber membranes were tested, which revealed that the PCL-COS-Qe membrane exhibited superior performance among all nanofiber membranes. Therefore, the developed PCL-COS-Qe/Ru nanofiber membranes hold enormous potential as healthcare products, such as wound dressings for burn injuries.

Effective tetracycline removal from liquid streams of dairy manure via hierarchical poly (vinyl alcohol-co-ethylene)/polyaniline metal complex nanofibrous membranes

Antibiotic residues from animal wastes enter underground and surface water streams, posing high risks to public health. Novel technologies capable of removing the residues from the matrix of concern such as animal waste should be developed. This research investigates the development of nanofiber absorbent for removing tetracycline (TC) antibiotic residues from liquid streams of dairy manure produced in a typical dairy farm. Hierarchically structured nanofibrous adsorbent was developed through growing a uniform polyaniline (PAni) nanodots on poly (vinyl alcohol-co-ethylene) (EVOH) nanofiber membrane (NFM). Moreover, Cu²⁺ ions were chelated on the developed EVOH/PAni-Cl NFM to improve TC adsorption efficiency and selectivity. The TC adsorption capacities of EVOH/PAni-Cl-Cu²⁺ and EVOH/PAni-Cl) NFM were 1100 mg g^-1 and 600 mg g^-1 within 120 min., respectively. The NFMs adsorption efficiency was investigated using dairy wastewater. Initial TC concentrations in dairy wastewater sample varied between 20 and 50 ppm. The EVOH/PAni-Cl-Cu²⁺ NFM showed TC removal of 86% from dairy manure samples at 25 ppm initial TC concentration within 60 min. during batch mode treatment. Results showed that the dynamic binding efficiency of 450 mg g^-1 can be achieved at an initial TC concentration of 50 ppm. Furthermore, the NFM displayed efficient chemical and physical stability even after 8 cycles of reusing without significant changes in its performance or hazardous Cu²⁺ leaching.

Constructing Mesoporous Adsorption Channels and MOF-Polymer Interfaces in Electrospun Composite Fibers for Effective Removal of Emerging Organic Contaminants

Recently, metal-organic framework (MOF)-based electrospun fibers have attracted considerable attention as adsorbents for organic contaminant removal from water. To prepare these fibers, two common strategies including blending electrospinning and surface coating are employed. However, fibers obtained from the two strategies still have some disadvantages, such as adsorption site blockage and unstable loading. Here, we constructed interconnected mesopores in the electrospun zeolitic imidazolate framework-8 (ZIF-8)/polyacrylonitrile (PAN) fibers with the assistance of poly(vinylpyrrolidone) to expose more adsorption sites of ZIF-8 and make ZIF-8 more stable. Moreover, the mesopores could also enhance the diffusion of contaminant molecules and create MOF-polymer interfaces in the fiber, which improve the adsorption rate and adsorption capacity, respectively. The obtained fibers were used to adsorb antibiotic tetracycline from water. Benefiting from the mesoporous adsorption channels and the MOF-polymer interface, porous ZIF-8/PAN fibers showed faster adsorption kinetics than ZIF-8/PAN blending fibers and larger adsorption capacity than ZIF-8-coated PAN fibers and ZIF-8/PAN blending fibers. The maximum adsorption capacity of porous ZIF-8/PAN fibers was 885.24 mg/g, which is close to that of pure ZIF-8. After 10 adsorption-desorption cycles, the removal efficiency was still above 97%. In addition, porous ZIF-8/PAN fibers could act as the membrane adsorbents to dynamically separate tetracycline with a treated capacity of 9.93 × 10³ bed volumes. These results demonstrate that our prepared porous ZIF-8/PAN fibers have great potential in antibiotic drug removal.

Electrospun Functional Nanofiber Membrane for Antibiotic Removal in Water: Review

As a new kind of water pollutant, antibiotics have encouraged researchers to develop new treatment technologies. Electrospun fiber membrane shows excellent benefits in antibiotic removal in water due to its advantages of large specific surface area, high porosity, good connectivity, easy surface modification and new functions. This review introduces the four aspects of electrospinning technology, namely, initial development history, working principle, influencing factors and process types. The preparation technologies of electrospun functional fiber membranes are then summarized. Finally, recent studies about antibiotic removal by electrospun functional fiber membrane are reviewed from three aspects, namely, adsorption, photocatalysis and biodegradation. Future research demand is also recommended.

Development of TiO2-coated YSZ/silica nanofiber membranes with excellent photocatalytic degradation ability for water purification

Numerous reports have elucidated that TiO2 nanoparticles (TiO2-NPs) exhibit respectable photocatalytic degradation capacities due to their high specific surface areas. However, the current recovery process leads to a loss of TiO2-NPs; therefore, there is a need to immobilize TiO2-NPs on the substrate used. Herein, TiO2-coated yttria-stabilized zirconia/silica nanofiber (TiO2-coated YSZ/silica NF) was prepared by coating TiO2 on the surface of YSZ/silica NF using a sol-gel process. The TiO2 coating layer on the nanofiber surface improved the separation ability of the membrane as well as the photocatalytic degradation ability. The pore size of the TiO2-coated YSZ/silica NF membrane was less than that of the pristine YSZ/silica NF membrane, and it rejected over 99.6% of the 0.5 μm polymeric particles. In addition, the TiO2-coated YSZ/silica NF membrane showed excellent adsorption/degradation of humic acid (HA, 88.2%), methylene blue (MB, 92.4%), and tetracycline (TC, 99.5%). Six recycling tests were performed to evaluate the reusability of the TiO2-coated YSZ/silica NF membrane. The adsorption/degradation efficiency for HA, MB, and TC decreased by 3.7%, 2.8%, and 2.2%, respectively. We thus verified the high separation ability, excellent photocatalytic degradation ability, and excellent reusability of the TiO2-coated YSZ/silica NF membranes.

Preparation of a Three-Dimensional Porous Graphene Oxide-Kaolinite-Poly(vinyl alcohol) Composite for Efficient Adsorption and Removal of Ciprofloxacin

Because of the widespread presence of antibiotics in water, soil, and other environments, they pose great potential risks to the environment, threatening human and animal health. In this study, graphene oxide-kaolinite homogeneous dispersion was prepared by simple liquid phase exfoliation. The three-dimensional (3D) porous graphene oxide-kaolinite-poly(vinyl alcohol) composites were prepared by the cross-linking of poly(vinyl alcohol) and the formation of ice crystals during the freezing-drying process. Three influencing factors [adsorbent dosage, ciprofloxacin (CIP) initial concentration, and time] of CIP adsorption and removal were systematically analyzed by the response surface method. The order of significance for response values (CIP removal rate) was adsorbent dosage > CIP initial concentration > time. The 3D porous material showed good adsorption capacity of CIP, the theoretical maximum adsorption capacity was 408.16 mg/g, and it had good recyclability. By Fourier transform infrared (FTIR) and X-ray photoelectron spectroscopy analysis, it was found the composite adsorbs CIP by hydrogen bonding and π-π interaction. In conclusion, the graphene oxide-kaolinite-poly(vinyl alcohol) porous composite is a good candidate for efficient antibiotic wastewater treatment.

Key role of pore size in Cr(VI) removal by the composites of 3-dimentional mesoporous silica nanospheres wrapped with polyaniline

A series of three-dimensional silica nanospheres with different pore sizes was synthesized in a biphasic oil-water system and their pore dimensions were adjusted by controlling the composition of the oil phase. The silica nanospheres were then wrapped with polyaniline, characterized, and the obtained silica nanosphere-polyaniline composites were used for the removal of Cr(VI). Polyaniline was generated by the polymerization of aniline. The mesoporous silica has sufficient dendritic pore channels and offers a large contact surface for the polymerization of aniline. Furthermore, the mesoporous silica nanospheres are beneficial for dispersing polyaniline and transferring aqueous Cr(VI). The silica nanosphere-polyaniline composite with the largest pore size (~15.4 nm) showed the best Cr(VI) removal performance. We also investigated the kinetic characteristics and the result could be fitted to the pseudo-second-order kinetic model. Moreover, we demonstrate that the composites maintain a high Cr(VI) removal efficiency compared to other anions (H₂PO₄^-, SO₄^2-, etc.), indicating their good prospect in practical wastewater treatment. Remarkably, the silica-polyaniline composites showed enhanced Cr(VI) removal efficiency under UV-irradiation. The effects of electrons and H⁺ on Cr(VI) reduction are also discussed based on the results of UV-vis and X-ray photoelectron spectroscopic studies and bath experiments (influence of pH on adsorption capacity). Mechanistic studies indicate that the Cr(VI) removal occurs in two stages-adsorption and reduction. The negatively charged aqueous Cr(VI) species first interact with the positively charged protonated amine groups via electrostatic attraction, and are then further reduced to less-toxic Cr(III) by the electrons and H⁺ donated by the amine groups on polyaniline.

Enhanced Strategies for Antibiotic Removal from Swine Wastewater in Anaerobic Digestion

There is a need for techniques that ensure antibiotic removal in anaerobic digesters for robust methane production. In this article, we discuss recent strategies for enhanced antibiotic removal from swine wastewater and offer insights on anaerobic digestion (AD) process design for improved antibiotic removal.

Poly(acryloyl hydrazide)-grafted cellulose nanocrystal adsorbents with an excellent Cr(VI) adsorption capacity

In this study, we prepared poly(acryloyl hydrazide) (PAH)-grafted cellulose nanocrystal (CNC-PAH) particles via the atom transfer radical polymerization method for application to Cr(VI) adsorption. The closely-packed PAH chains grafted on the cellulose nanocrystal (CNC) surface provide a high density of amine groups that can adsorb Cr(VI) through strong electrostatic, hydrogen bonding and chelating interactions. CNC-PAH exhibited the optimum Cr(VI) adsorption capacity at the solution pH = 3, where its electrostatic attraction with Cr(VI) was maximized. Cr(VI) was chemisorbed in CNC-PAH by following the Langmuir isotherm mechanism (homogeneous monolayer adsorption). The Cr(VI) adsorption kinetics of CNC-PAH was controlled predominantly by intra-particle diffusion resistance imparted by the PAH shell layer. Thermodynamic analysis revealed that Cr(VI) adsorption of CNC-PAH is a spontaneous and endothermic process. Importantly, CNC-PAH grafted with the higher M_w (∼50 kg mol^-1) PAH exhibited a rapid Cr(VI) adsorption rate and remarkably high Cr(VI) adsorption capacity (∼457.6 mg g^-1 at 298.15 K), exceeding those of previously reported adsorbents owing to its numerous Cr(VI)-adsorptive amine groups provided by the closely-packed grafted PAH polymers. Furthermore, CNC-PAH showed excellent reusability to maintain its high adsorption ability during repeated adsorption-desorption cycles owing to the covalently binding nature of the PAH polymers.