Highly Compressible Wood Sponges with a Spring-like Lamellar Structure as Effective and Reusable Oil Absorbents

An overview of cellulose aerogels and foams for oil sorption: Preparation, modification, and potential of 3D printing

Sorption is one of the most efficient methods to remediate the increasing oil spill incidents, but the currently available absorbents are inadequate to tackle such a global threat. Recently, numerous researchers have attempted to develop sustainable oil sorbents. Cellulose aerogels and foams, a type of lightweight porous material with excellent sorption performance, are one of the most promising candidates. Significant progress has been made in the past decade towards the development of cellulose porous materials as effective oil sorbents, with improvements in their oil sorption capacity, reusability, and enhanced multifunctionality, indicating their potential for oil spill remediation. This article reviews recent reports and provides a comprehensive overview of the preparation and modification strategies for cellulose porous materials, with a specific emphasis on their oil sorption performance and structure control. We also focus on the burgeoning 3D printing technology within this field, summarizing the latest advances with a discussion of the potential for using 3D printing to customize and optimize the structure of cellulose porous materials. Lastly, this review addresses current limitations and outlines future directions for development.

Effectiveness Evaluation of Silicone Oil Emulsion In Situ Polymerization for Dehydration of Waterlogged Wooden Artifacts

Organosilicon materials have shown potential as dehydration agents for waterlogged wooden artifacts. These materials can polymerize under normal conditions to form polymers with favorable mechanical strength, antibacterial properties, and aging resistance. However, the insolubility of most organosilicon hindered their penetration into waterlogged wood, which may lead to an unwanted cracking. This study aimed to evaluate the effectiveness of polydimethylsiloxane (PDMS) and hydroxy-terminated polydimethylsiloxane (PDMS-OH) with low viscosity and moderate reactivity for dehydrating waterlogged wooden artifacts from the Nanhai No.1 shipwreck. Four surfactants ((3-aminopropyl) triethoxysilane (APTES), alkyl polyoxyethylene ether (APEO), tri-methylstearylammonium chloride (STAC), and fatty alcohol polyoxyethylene ether (AEO)) and cosurfactant were employed to transform the two kinds of water-repellent silicone oils into eight groups of highly permeable oil-in-water (O/W) emulsions. Under the catalysis of a neutral catalyst, in situ polymerization occurred within the wood cells. Group P2-2 formulated with PDMS-OH and APEO showed the best efficiency in maintaining the dimensions of the wood during dehydration. The dehydrated wood exhibited a natural color and texture with a minimal volume shrinkage rate of 1.89%. The resulting polymer adhered uniformly to the cell walls, effectively reinforcing the wood cell structure. The weight percent gain of the wood was only 218%, and the pores of the cell lumen were well maintained for future retreatment. This method effectively controlled the sol-gel reaction process of the organosilicon and prevented damage to the wooden artifact during the dehydration process. Moreover, the dehydrated wood samples only experienced a low weight gain of 17% at 95% relative humidity (RH), indicating their great environmental stability.

One-pot fabrication of hydrophobic, superelastic, harakeke-derived nanocellulose aerogels with excellent shape recovery for oil adsorption and water-in-oil emulsion separation

Cellulose-based aerogels have attracted significant attention for oil/water separation due to their high porosity, large specific surface area and high adsorption capacity. However, their intrinsic hydrophilicity, and inadequate mechanical properties have often limited their practical applications. Traditional freeze-dried cellulose aerogels exhibit unsatisfactory elasticity and require a separate surface modification process to adjust the surface wettability. In this study, we present a novel one-pot fabrication strategy which simultaneously achieves the crosslinking of individual cellulose nanofibers and the hydrophobic modification of the surface wettability. Following directional freeze-drying, hydrophobic, superelastic, and anisotropic cellulose-based aerogel was prepared from the 2,2,6,6-tetramethylpiperidin-1-oxyl (TEMPO)-oxidized cellulose nanofibers, isolated from harakeke (New Zealand native flax). The resulting aerogel exhibits a high water contact angle of 142°, good compressive recovery performance (85 % recovery of the original height after 100 compression cycles at 70 % strain), and outstanding adsorption capacity for various types of oil and organic solvents (80-105 g/g). Furthermore, the aerogel could also be used as a filter to separate surfactant stabilized water-in-oil emulsions with a high flux (782 L m-2 h-1) and a high separation efficiency (98.7-99.2 %). The novel aerogel prepared in this study is expected to have great potential for practical applications in oily wastewater remediation.

Efficient preparation of anisotropic cellulose sponge from cotton stalks: An excellent material for separation applications

Water pollution and solid waste resource reuse demand immediate attention and research. Here, we present a method to create anisotropic cellulose sponges from cotton stalk waste. Using the inherent structure of cotton stalks, we selectively remove lignin and hemicellulose via acid and alkali pretreatment. This process yields cellulose sponges with a natural pore structure. Our findings demonstrate that these sponges retain the original pore configuration of cotton stalks, providing excellent connectivity and compressibility due to their unique anisotropic three-dimensional structure. Moreover, these sponges exhibit exceptional super-hydrophilic and underwater super-oleophobic properties, with underwater oil contact angles exceeding 150° for all tested oils. External pressure can reduce the pore size of the cellulose sponge, facilitating the gravity-driven separation and removal of dyes and emulsions. Remarkably, removal efficiencies for Methylene Blue (MB), Congo Red (CR), water-in-oil (w/o) emulsions, and oil-in-water (o/w) emulsions exceed 99 %, 97 %, 99 %, and 99 %, respectively, highlighting superior removal and recyclability. Further investigation into the mechanisms of dye and emulsion removal employs X-ray photoelectron spectroscopy (XPS) characterization and molecular dynamics (MD) simulation. These insights lay the groundwork for the efficient recycling and resource utilization of waste cotton stalks, offering promising applications in water purification.

Wood Sponge for Oil-Water Separation

In addition to filtering some sediments, hydrophobic wood sponges can also absorb many organic solvents, particularly crude oil. The leakage of crude oil poses a serious threat to the marine ecosystem, and oil mixed with water also generates great danger for its use. From the perspective of low cost and high performance, wood sponges exhibit great potential for dealing with crude oil pollution. Wood sponge is a renewable material. With a highly oriented layered structure and a highly compressible three-dimensional porous frame, wood sponges are extremely hydrophobic, making them ideal for oil-water separation. Currently, the most common approach for creating wood sponge is to first destroy the wood cell wall to obtain a porous-oriented layered structure and then enhance the oil-water separation ability via superhydrophobic treatment. Wood sponge prepared using various experimental methods and different natural woods exhibits distinctive properties in regards to robustness, compressibility, fatigue resistance, and oil absorption ability. As an aerogel material, wood sponge offers multi-action (absorption, filtration) and reusable oil-water separation functions. This paper introduces the advantages of the use of wood sponge for oil-water separation. The physical and chemical properties of wood sponge and its mechanism of adsorbing crude oil are explained. The synthesis method and the properties are discussed. Finally, the use of wood sponge is summarized and prospected.

Ceramic Meta-Aerogel with Thermal Superinsulation up to 1700 °C Constructed by Self-Crosslinked Nanofibrous Network via Reaction Electrospinning

Thermal insulation under extreme conditions requires the materials to be capable of withstanding complex thermo-mechanical stress, significant gradient temperature transition, and high-frequency thermal shock. The excellent structural and functional properties of ceramic aerogels make them attractive for thermal insulation. However, in extremely high-temperature environments (above 1500 °C), they typically exhibit limited insulation capacity and thermo-mechanical stability, which may lead to catastrophic accidents, and this problem is never effectively addressed. Here, a novel ceramic meta-aerogel constructed from a crosslinked nanofiber network using a reaction electrospinning strategy, which ensures excellent thermo-mechanical stability and superinsulation under extreme conditions, is designed. The ceramic meta-aerogel has an ultralow thermal conductivity of 0.027 W m-1 k-1, and the cold surface temperature is only 303 °C in a 1700 °C high-temperature environment. After undergoing a significant gradient temperature transition from liquid nitrogen to 1700 °C flame burning, the ceramic meta-aerogel can still withstand thousands of shears, flexures, compressions, and other complex forms of mechanical action without structural collapse. This work provides a new insight for developing ceramic aerogels that can be used for a long period in extremely high-temperature environments.

A comprehensive review on preparation and functional application of the wood aerogel with natural cellulose framework

As the traditional aerogel has defects such as poor mechanical properties, complicated preparation process, high energy consumption and non-renewable, wood aerogel as a new generation of aerogel shows unique advantages. With a natural cellulose framework, wood aerogel is a novel nano-porous material exhibiting exceptional properties such as light weight, high porosity, large specific surface area, and low thermal conductivity. Furthermore, its adaptability to further functionalization enables versatile applications across diverse fields. Driven by the imperative for sustainable development, wood aerogel as a renewable and eco-friendly material, has garnered significant attention from researchers. This review introduces preparation methods of wood aerogel based on the top-down strategy and analyzes the factors influencing their key properties intending to obtain wood aerogels with desirable properties. Avenues for realizing its functionality are also explored, and research progress across various domains are surveyed, including oil-water separation, conductivity and energy storage, as well as photothermal conversion. Finally, potential challenges associated with wood aerogel exploitation and utilization are addressed, alongside discussions on future prospects and research directions. The results emphasize the broad research value and future prospects of wood aerogels, which are poised to drive high-value utilization of wood and foster the development of green multifunctional aerogels.

Optimization of mechanical properties and dimensional stability of densified wood using response surface methodology

Wood has gained popularity as a building and decorative material due to its environmentally friendly and sustainable characteristics. Yet, its long maturation time poses a limitation on meeting the growing demand for wood products. This challenge has led to the plantation of fast-growing wood as an alternative solution. Unfortunately, the poor mechanical properties of fast-growing wood hinder its application. In this study, we developed novel densification-modified wood by combining alkali chemical pretreatment, cyclic impregnation, and mechanical hot-pressing techniques. Additionally, the response surface method was employed to rapidly determine the optimal preparation parameters, reducing the cost of preparation under various conditions. The optimized parameters resulted in densification-modified wood with a flexural strength and modulus of elasticity of 337.04 MPa and 27.43 GPa, respectively. Furthermore, the densified wood achieved excellent dimensional stability by reducing the water-absorbing thickness swelling to 1.15 % for 72-h water soaking. The findings indicated that the densification-modified wood possessed high tensile strength and elastic modulus, along with excellent dimensional stability. The proposed densified wood modification technology in this study offers new perspectives and design guidance for the application of outdoor engineering structures, energy-efficient buildings, and decorative materials.

Preparation of Fibrous Three-Dimensional Porous Materials and Their Research Progress in the Field of Stealth Protection

Intelligent and diversified development of modern detection technology greatly affects the battlefield survivability of military targets, especially infrared, acoustic wave, and radar detection expose targets by capturing their unavoidable infrared radiation, acoustic wave, and electromagnetic wave information, greatly affecting their battlefield survival and penetration capabilities. Therefore, there is an urgent need to develop stealth-protective materials that can suppress infrared radiation, reduce acoustic characteristics, and weaken electromagnetic signals. Fibrous three-dimensional porous materials, with their high porosity, excellent structural adjustability, and superior mechanical properties, possess strong potential for development in the field of stealth protection. This article introduced and reviewed the characteristics and development process of fibrous three-dimensional porous materials at both the micrometer and nanometer scales. Then, the process and characteristics of preparing fibrous three-dimensional porous materials through vacuum forming, gel solidification, freeze-casting, and impregnation stacking methods were analyzed and discussed. Meanwhile, their current application status in infrared, acoustic wave, and radar stealth fields was summarized and their existing problems and development trends in these areas from the perspectives of preparation processes and applicability were analyzed. Finally, several prospects for the current challenges faced by fibrous three-dimensional porous materials were proposed as follows: functionally modifying fibers to enhance their applicability through self-cross-linking; establishing theoretical models for the transmission of thermal energy, acoustic waves, and electromagnetic waves within fibrous porous materials; constructing fibrous porous materials resistant to impact, shear, and fracture to meet the needs of practical applications; developing multifunctional stealth fibrous porous materials to confer full-spectrum broadband stealth capability; and exploring the relationship between material size and mechanical properties as a basis for preparing large-scale samples that meet the application's requirement. This review is very timely and aims to focus researchers' attention on the importance and research progress of fibrous porous materials in the field of stealth protection, so as to solve the problems and challenges of fibrous porous materials in the field of stealth protection and to promote the further innovation of fibrous porous materials in terms of structure and function.

Superhydrophobic Co-MOF-based sponge for efficient oil-water separation utilizing photothermal effect

Effectively addressing crude oil spills remains a global challenge due to its high viscosity and limited flow characteristics. In this study, we successfully prepared a modified sponge (PCP@MS) by embedding the photothermal material of Co-HHTP and coating the melamine sponge (MS) with low-surface-energy polydimethylsiloxane (PDMS). The PCP@MS exhibited outstanding hydrophobicity with WCA of 160.2° and high oil absorption capacity of 59-107 g/g. The PCP@MS showed high separation efficiency of 99.2% for various oil-water mixtures, along with notable self-cleaning properties and mechanical stability. The internal micro-nano hierarchical structure on the sponge surface significantly enhanced light absorption, synergizing with the photo-thermal conversion properties of Co-HHTP, enabled PCP@MS to achieve a surface temperature of 109.2 °C under 1.0 solar light within 300 s. With the aid of solar radiation, PCP@MS is able to heat up quickly and successfully lowering the viscosity of the surrounding crude oil, resulting in an oil recovery rate of 8.76 g/min. Density functional theory (DFT) calculation results revealed that Co-HHTP featured a zero-gap band structure, rendering advantageous electronic properties for full-wavelength light absorption. This in situ solar-heated absorbent design is poised to advance the practical application of viscous oil spill cleanup and recovery.

Metallic Wood through Deep-Cell-Wall Metallization: Synthesis and Applications

Metallic wood combines the unique structural benefits of wood and the properties of metals and is thus promising for applications ranging from heat transfer to electromagnetic shielding to energy conversion. However, achieving metallic wood with full use of wood structural benefits such as anisotropy and multiscale porosity is challenging. A key reason is the limited mass transfer in bulk wood where fibers have closed ends. In this work, programmed removal of cell-wall components (delignification and hemicellulose extraction) was introduced to improve the accessibility of cell walls and mass diffusion in wood. Subsequent low-temperature electroless Cu plating resulted in a uniform continuous Cu coating on the cell wall, and, furthermore, Cu nanoparticles (NPs) insertion into the wood cell wall. A novel Cu NPs-embedded multilayered cell-wall structure was created. The unique structure benefits compressible metal-composite foam, appealing for stress sensors, where the multilayered cell wall contributes to the compressibility and stability. The technology developed for wood metallization here could be transferred to other functionalizations aimed at reaching fine structure in bulk wood.

Rational Design of Amorphous Carbon-Coated Laminar-Structured Wood for Integrating Repeatable Early Fire Detection and High-Temperature Affordable Flexible Pressure Sensing in One System

High-temperature affordable flexible polymer-based pressure sensors integrated with repeatable early fire warning service are strongly desired for harsh environmental applications, yet their creation remains challenging. This work proposed an approach for preparing such advanced integrated sensors based on silver nanoparticles and an ammonium polyphosphate (APP)-modified laminar-structured bulk wood sponge (APP/Ag@WS). Such integrated sensors demonstrated excellent fire warning performance, including a short response time (minimum of 0.44 s), a long-lasting alarm time (>750 s), and reliable repeatability. Moreover, it achieved high-temperature affordable flexible pressure sensing that exhibited an almost unimpaired working range of 0-7.5 kPa and a higher sensitivity (in the low-pressure range, maximum to 226.03 kPa-1) after fire. The high stability was attributed to reliable structural elasticity, and the wood-derived amorphous carbon is capable of repeatable fire warnings. Finally, a Ag@APP/WS-based wireless fire alarm system that realized reliable house fire accident detection was demonstrated, showing great promise for smart firefighting application.

Wet-Stable Lamellar Wood Sponge with High Elasticity and Fatigue Resistance Enabled by Chemical Cross-Linking

The excessive consumption of fossil-based plastics and the associated environmental concerns motivate the increasing exploitation of sustainable biomass-based materials for advanced applications. Natural wood-derived lamellar wood sponges via a top-down approach have recently attracted significant attention; however, the insufficient compressive fatigue resistance and lack of structural stability in water limit their wide applications. Here, we report a facile chemical cross-linking strategy to tackle these challenges, by which the cellulose fibrils in the lamellas are covalently bridged to enhance their connectivity. The cross-linked wood sponges demonstrate high compressibility up to 70% strain and exceptional compressive fatigue resistance (∼5% plastic deformation after 10,000 cycles at 50% strain). The interfibrillar cross-linking inhibits the swelling of cellulose fibrils and preserves the arch-shaped lamellas of the sponge in water, endowing the wood sponge with excellent wet stability. Such highly elastic and wet-stable lamellar wood sponges offer a sustainable alternative to synthetic polymer-based sponges used in diverse applications.

Stereo-complex polylactide composite aerogel for crude oil adsorption

Adsorption materials are a cost-effective and simple method for oil spill remediation, but their efficiency is limited by high crude oil viscosity. Additionally, non-degradable materials pose another risk of secondary pollution, such as microplastic debris. Here, an environmentally-friendly stereo-complex polylactide composite (SCC) aerogel were developed via water-assisted thermally induced phase separation. The SCC with 3 wt% carbon nanotubes had a hierarchical structure of micro/nanoscale pores and high content of stereo-complex crystallites (35.7 %). Along with the excellent water repellency (water contact angle: 157°), SCC aerogel was 2.7 times as resistant to hydrolysis than poly(l-lactide) aerogel (Ph = 13, 37 °C). Additionally, a maximum absorption capacity of 41.2 g g-1 and over 97 % oil/water separation efficiency after 10 cycles were obtained in low viscosity conditions; while in high viscosity conditions, it displayed excellent photothermal performance, reaching a surface temperature of 85 °C under 1 sunlight, reducing crude oil absorption time from 42 min to 60 s (97.6 %-time savings). Moreover, it facilitated continuous crude oil spill recovery under sunlight with an adsorption rate of 3.3 × 104 kg m-3 h-1. The SCC aerogel presents a potential route for utilizing solar energy in crude oil adsorption applications without additional environmental burden.

Solid Wood Modification toward Anisotropic Elastic and Insulative Foam-Like Materials

The methods used to date to produce compressible wood foam by top-down approaches generally involve the removal of lignin and hemicelluloses. Herein, we introduce a route to convert solid wood into a super elastic and insulative foam-like material. The process uses sequential oxidation and reduction with partial removal of lignin but high hemicellulose retention (process yield of 72.8%), revealing fibril nanostructures from the wood's cell walls. The elasticity of the material is shown to result from a lamellar structure, which provides reversible shape recovery along the transverse direction at compression strains of up to 60% with no significant axial deformation. The compressibility is readily modulated by the oxidation degree, which changes the crystallinity and mobility of the solid phase around the lumina. The performance of the highly resilient foam-like material is also ascribed to the amorphization of cellulosic fibrils, confirmed by experimental and computational (molecular dynamics) methods that highlight the role of secondary interactions. The foam-like wood is optionally hydrophobized by chemical vapor deposition of short-chained organosilanes, which also provides flame retardancy. Overall, we introduce a foam-like material derived from wood based on multifunctional nanostructures (anisotropically compressible, thermally insulative, hydrophobic, and flame retardant) that are relevant to cushioning, protection, and packaging.

Effective separation of water-in-oil emulsions using an under-medium superlyophilic membrane with hierarchical pores

Separating water-in-oil emulsions is important in terms of environmental protection and resource recovery. To address the challenges posed by the water-oil interface, superwetting materials have been designed to accomplish separation through filtration and adsorption. Superhydrophobic membranes prevent the permeation of water droplets owing to extreme repellence and their size-sieving abilities. However, their use in remediating water-contaminated oil is limited by high oil viscosities. Meanwhile, in-air superhydrophilic sorbents are rarely employed for the separation of water-in-oil emulsions due to the thermodynamic and kinetic limitations of water adsorption in oil. Herein, the integration of an under-medium superlyophilic membrane with the hierarchical porous structure of wood is presented for filtration-driven selective adsorption of water from surfactant-stabilized (10 g/L) water-in-oil emulsions. Compared to filtration through a natural wood membrane or direct adsorption using an under-oil superhydrophilic wood membrane, the under-medium superlyophilic wood membrane demonstrated high separation efficiencies of > 99.95% even when applied to the regeneration of high-viscosity lubricating (6.3 mPa s) and edible (50.5 mPa s) oils, exhibiting viscosity-dependent fluxes and excellent stability. Moreover, the cost of purifying 200 mL of lubricating oil using the modified wood membrane was much lower than the oil's market price and required a low energy consumption of ca. 1.72 kWh. ENVIRONMENTAL IMPLICATION: The ever-growing use of petroleum and industrial/domestic oil products has led to excessive (estimated at a million tons per year) output of waste oils. Because direct discharge of waste oils into the environment causes serious pollution problems, separating water-in-oil emulsions is important in terms of environmental protection and resource recovery. Here filtration-driven water adsorption has been demonstrated to be a feasible method for the remediation of water-contaminated waste oils, even those that are highly viscous.

In Situ Growth of MOF from Wood Aerogel toward Bromide Ion Adsorption in Simulated Saline Water

Utilizing metal-organic framework (MOF) materials for the extraction of bromide ions (Br-) from aqueous solutions, as an alternative to chlorine gas oxidation technology, holds promising potential for future applications. However, the limitations of powdered MOFs, such as low utilization efficiency, ease of aggregation in water, and challenging recovery processes, have hindered their practical application. Shaping MOF materials into application-oriented forms represents an effective but challenging approach to address these drawbacks. In this work, a novel Ag-UiO-66-(OH)2@delignified wood cellulose aerogel (CA) adsorbent is synthesized using an oil bath impregnation method, involving the deposition of UiO-66-(OH)2 nanoparticles onto CA and the uniform dispersion of Ag0 nanoparticles across its surface. CA, characterized by the intertwined cellulose nanofiber structure and a highly hydrophilic surface, serves as an ideal substrate for the uniform growth of UiO-66-(OH)2 nanoparticles, which, in turn, spontaneously reduce Ag+ to form distributed Ag0 nanoparticles due to the abundant hydroxyl groups provided. Leveraging the well-defined biological structure of CA, which offers excellent mass transfer channels, and the highly dispersed Ag adsorption sites, Ag-UiO-(OH)2/CA exhibits remarkable adsorption capacity (642 mg/gAg) under optimized conditions. Furthermore, an integrated device is constructed by interconnecting Ag-UiO-(OH)2/CA adsorbents in series, affirming its potential application in the continuous recovery of Br-. This study not only presents an efficient Ag-UiO-(OH)2/CA adsorbent for Br- recovery but also sheds light on the extraction of other valuable elements from various liquid ores.

Promoting Electromagnetic Wave Absorption Performance by Integrating MoS2@Gd2O3/MXene Multiple Hetero-Interfaces in Wood-Derived Carbon Aerogels

Multi-component composite materials with a magnetic-dielectric synergistic effect exhibit satisfactory electromagnetic wave absorption performance. However, the effective construction of the structure for these multi-component materials to fully exploit the advantages of each component remains a challenge. Inspired by natural biomass, this study utilizes wood as the raw material and successfully prepares high-performance MoS2@Gd2O3/Mxene loaded porous carbon aerogel (MGMCA) composite material through a one-pot hydrothermal method and carbonization treatment process. With a delicate structural design, the MGMCA is endowed with abundant heterogeneous interface structures, favorable impedance matching characteristics, and a magnetic-dielectric synergistic system, thus demonstrating multiple electromagnetic wave loss mechanisms. Benefiting from these advantages, the obtained MGMCA exhibits outstanding electromagnetic wave absorption performance, with a minimum reflection loss of -57.5 dB at an ultra-thin thickness of only 1.9 mm. This research proposes a reliable strategy for the design of multi-component composite materials, providing valuable insight for the design of biomass-based materials as electromagnetic wave absorbers.

Superelastic and superflexible cellulose aerogels for thermal insulation and oil/water separation

Aerogels with low thermal conductivity and high adsorption capacity present a promising solution to curb water pollution caused by organic reagents as well as mitigate heat loss. Although aerogels exhibiting good adsorption capacity and thermal insulation have been reported, materials with mechanical integrity, high flexibility and shear resistance still pose a formidable task. Here, we produced bacterial cellulose-based ultralight multifunctional hybrid aerogels by using freeze-drying followed by chemical vapor deposition silylation method. The hybrid aerogels displayed a low density of 10-15 mg/cm3, high porosity exceeding 99.1 %, low thermal conductivity (27.3-29.2 mW/m.K) and superior hydrophobicity (water contact angle>120o). They also exhibited excellent mechanical properties including superelasticity, high flexibility and shear resistance. The hybrid aerogels demonstrated high heat shielding efficiency when used as an insulating material. As a selective oil absorbent, the hybrid aerogels exhibit a maximum adsorption capacity of up to approximately 156 times its own weight and excellent recoverability. Especially, the aerogel's highly accessible porous microstructure results in an impressive flux rate of up to 162 L/h.g when used as a filter in a continuous oil-water separator to isolate n-hexane-water mixtures. This work presents a novel endeavor to create high-performance, sustainable, reusable, and adaptable multifunctional aerogels.

Construction of Nanofibrillar Networked Wood Aerogels Derived from Typical Softwood and Hardwood: A Comparative Study on the In Situ Formation Mechanism of Nanofibrillar Networks

The construction of networks within natural wood (NW) lumens to produce porous wood aerogels (WAs) with fascinating characteristics of being lightweight, flexible, and porous is significant for the high value-added utilization of wood. Nonetheless, how wood species affect the structure and properties of WAs has not been comprehensively investigated. Herein, typical softwood of fir and hardwoods of poplar and balsa are employed to fabricate WAs with abundant nanofibrillar networks using the method of lignin removal and nanofibril's in situ regeneration. Benefiting from the avoidance of xylem ray restriction and the exposure of the cellulose framework, hardwood has a stronger tendency to form nanofibrillar networks compared to softwood. Specifically, a larger and more evenly distributed network structure is displayed in the lumens of balsa WAs (WA-3) with a low density (59 kg m-3), a high porosity (96%), and high compressive properties (strain = 40%; maximum stress = 0.42 MPa; height retention = 100%) because of the unique structure and properties of WA-3. Comparatively, the specific surface area (SSA) exhibits 25-, 27-, and 34-fold increments in the cases of fir WAs (WA-1), poplar WAs (WA-2), and WA-3. The formation of nanofibrillar networks depends on the low-density and thin cell walls of hardwood. This work offers a foundation for investigating the formation mechanisms of nanonetworks and for expanding the potential applications of WAs.

Versatile Mesoporous All-Wood Sponge Enabled by In Situ Fibrillation toward Indoor-Outdoor Energy Management and Conversion

The on-demand regulation of cell wall microstructures is crucial for developing wood as a functional building material for energy management and conversion. Here, a novel strategy based on reactive deep eutectic solvent is developed to one-step in situ fibrillate wood via disrupting the hydrogen bonding networks in cell walls and simultaneously carboxylating wood components, without significantly altering the native hierarchical structures of wood. Benefiting from its distinctive cell wall structure composed of individualized yet well-organized lignocellulose nanofibrils, in situ fibrillated wood exhibits a prominent mesoporous structure with a specific surface area of 81 m2/g. It represents a robust sponge material (5 MPa at 80% strain) with excellent durability. Due to the enhanced compressibility and charge polarization capacity, the in situ fibrillated wood (10 × 11 × 12 mm3) can generate a piezoelectric output voltage of up to 2 V under 221 kPa stress. The favorable microstructural characteristics render in situ fibrillated wood with highly thermal-insulating properties, high solar reflectivity, and mid-infrared emissivity, favoring outdoor passive cooling effects with a subambient temperature drop of 6 °C. Combining its controllable, durable, and eco-friendly attributes, our developed wood sponge represents a versatile structural material suitable for indoor/outdoor energy-saving applications.

Development of super dimensional stable poplar structure with fire and mildew resistance by delignification/densification of wood with highly aligned cellulose molecules

Wood is one of the most popular materials for construction purposes because of its environmentally friendly and sustainable characteristics. However, the use of wood is constrained by the lengthy time it takes for trees to mature. Consequently, fast-growing wood species have become popular as substitute options due to their ability to rapidly reach maturity and high yields. Although the problem of low density and strength has been effectively addressed in recent years by densifying wood, the problem of large thickness swelling due to moisture and water absorption has limited its application. Therefore, we reported an effective modification strategy to overcome the thickness swelling issue of densified wood by preparing a cellulosic reinforced material through the synergistic action of alkaline chemical pretreatment, multi-step cyclic impregnation and high-temperature densification. The results showed that the alkaline chemical pretreatment was effective for removing a large amount of lignin and hemicelluloses, creating a large number of hydrogen bonds among the remaining strong celluloses. The impregnated sodium silicate solution bonded celluloses tightly, and the densification treatment contributed to the production of Si-O-Si structure, forming the shuttle hybridized structure through Si-O-C bonds. The hardness, flexural strength, elastic modulus, and compressive strength of the modified wood increased by 3.9, 6.0, 3.4 and 28.2 times, respectively. In addition, 0 % thickness swelling for 30-day moisture absorption and 1.0 % thickness swelling for 72-hour water absorption were achieved, realizing super dimensional-stable poplar structures. Furthermore, the high-performance densified wood prepared by this method has excellent fire and mildew resistance properties, which lays the foundation for the application of fast-growing wood in outdoor engineering structures.

Recent advances in hydrophobic nanocellulose aerogels for oil spill applications: A review

In a rapidly growing world, petroleum is used extensively in various industries, and the extraction, processing, and transportation of petroleum generates large amounts of petroleum-containing wastewater. Conventional oil/water separation methodologies are often ineffective and costly. Nanocellulose-based aerogels (NA) have emerged as a possible solution to this problem. However, hydrophobic modification is required for effective use in oil/water separation. This review on materials commonly used in these processes and outlines the requirements for adsorbent materials and methods for creating unique lipophilic surfaces. New trends in hydrophobization methods for NA are also discussed. Additionally, it includes the development of composite nanocellulose aerogels (CNAs) and cellulose based membrane specially developed for oil/water (o/w) separation considering different separation requirements. This analysis also examines how CNAs have evolved by introducing special properties that facilitate oil collection or make the adsorbent recyclable. We also discuss the difficulties in creating effective NAs for these important applications in a changing society, as well as the difficulties in creating oil recovery equipment for oil spill cleanup.

Joule Heating-Assisted Crude Oil Purification by a Poly(pyrrole)-Modified Microfibril Cellulose Membrane

Using membrane materials to purify viscous watery oil from industrial production processes and accidental oil spills is of great importance but still challenging. Based on the excellent electrical conductivity and electric-thermal conversion of poly(pyrrole) (PPy), a hydrophobic PPy-modified micro-fibrillated cellulose membrane (P-CP) was successfully prepared. The size of the P-CP membrane can be customized to meet specific requirements. In this research, the membrane diameter is capable of reaching 24 cm. By applying a voltage ranging from 0 to 12 V, the surface temperature of the P-CP membrane can be elevated to roughly 120 °C. After 10 cycles of heating and cooling under 12 V voltage, the electric-thermal curves, surface hydrophobicity, and pore structure of P-CP membrane can remain stable, which suggests remarkable electric-thermal stability and reliability despite prolonged operation. The P-CP membrane shows good linearity between voltage and current (R2 = 0.997) and easy temperature control from room temperature to ∼120 °C at low supply voltage (0-12 V). Under the condition of 12 V power supply and self-gravity, the separation flux of the P-CP membrane for water-in-oil (W/O) emulsions (kerosene, diesel) is 2-3 times higher than that at room temperature, and the separation efficiency is also improved. Importantly, the P-CP membrane shows excellent separation performance for high viscosity water-in-crude oil emulsions, with a separation flux of 40 L m-2 h-1 by gravity. Compared to the situation without electricity, the separation flux of water-in-crude oil emulsion has increased four-fold. The joule heating of the P-CP membrane expands its service time and application scenarios, demonstrating its great application prospects in actual viscous oil-water emulsion separation.

Robust and Multifunctional Ti3 C2 Tx /Modified Sawdust Composite Paper for Electromagnetic Interference Shielding and Wearable Thermal Management

Robust, ultrathin, and environmental-friendliness papers that synergize high-efficiency electromagnetic interference (EMI) shielding, personal thermal management, and wearable heaters are essential for next-generation smart wearable devices. Herein, MXene nanocomposite paper with a nacre-like structure for EMI shielding and electrothermal/photothermal conversion is fabricated by vacuum filtration of Ti3 C2 Tx MXene and modified sawdust. The hydrogen bonding and highly oriented structure enhance the mechanical properties of the modified sawdust/MXene composite paper (SM paper). The SM paper with 50 wt% MXene content shows a strength of 23 MPa and a toughness of 13 MJ·M-3 . The conductivity of the SM paper is 10 195 S·m-1 , resulting in an EMI shielding effectiveness (SE) of 67.9 dB and a specific SE value (SSE/t) of 8486 dB·cm2 ·g-1 . In addition, the SM paper exhibits excellent thermal management performance including high light/electro-to-thermal conversion, rapid Joule heating and photothermal response, and sufficient heating stability. Notably, the SM paper exhibits low infrared emissivity and distinguished infrared stealth performance, camouflaging a high-temperature heater surface of 147-81 °C. The SM-based e-skin achieves visualization of Joule heating and realizes human motions monitoring. This work presents a new strategy for designing MXene-based wearable devices with great EMI shielding, artificial intelligence, and thermal management applications.

Hollow glass microspheres embedded in porous network of chitosan aerogel used for thermal insulation and flame retardant materials

In recent years, biopolymer aerogels as thermal insulation materials have received widespread attention due to natural abundance, cost-efficiency, and environment-friendly. However, the flammability and low strength hinder its practical application. Hollow glass microspheres (HGMs) as an inorganic thermal insulation filler have been filled in biopolymer aerogels to improve flame retardancy. However, the structure formed by HGMs embedded porous network of biopolymer aerogel has rarely been investigated, which not only reduce thermal conductivity through high porosity, but also adjust the filling volume of HGMs and achieve uniform distribution through chemical cross-linking. Herein, a biopolymer aerogel composite was assembled by chitosan aerogel (CSA) and different volume of HGMs by chemical cross-linking, freeze-drying, and silylation modification processes. When the filling volume fraction of HGMs reached 40 %, a skeleton structure was initially formed. The composites with HGMs volume of 40 %-60 % exhibited low density, high porosity, low thermal conductivity, good mechanical property, and excellent flame retardancy. According to GB 8624-2012 standard for classification, the composite with 60 % HGMs achieved class A1 non-combustible.

Polydopamine/Fe3O4 modified wood-based evaporator for efficient and continuous water purification

Solar interfacial evaporation is a highly promising technology for seawater desalination and wastewater treatment, while the simple preparation processes and efficient production of clean water based on biomass interfacial evaporators still need further exploration and development. Here, we reported a wood-based evaporator (PFDW) loaded with Fe3O4 and polydopamine (PDA) after simple immersion treatment at room temperature for efficient and continuous water purification. The synergistic photothermal effect of PDA coating and Fe3O4 particles enables the evaporator to achieve high photothermal conversion efficiency in the longer wavelength range, while combined with the rapid water transport capacity endowed by the vertically aligned microporous structure of natural wood, it achieved an evaporation rate of 1.70 kg m-2h-1 and an energy efficiency of 98.0% under 1 kW m-2 irradiation. In addition, the prepared PFDW exhibited sustainable desalination stability and excellent removal efficiency for different water sources including organic dye wastewater, heavy metal effluent, oil-water emulsion and river water. This work provides a new avenue for efficient salt-tolerant portable evaporators.

Research Advances in Wood Composites in Applications of Industrial Wastewater Purification and Solar-Driven Seawater Desalination

In recent years, the ecosystem has been seriously affected by sewage discharge and oil spill accidents. A series of issues (such as the continuous pollution of the ecological environment and the imminent exhaustion of freshwater resources) are becoming more and more unmanageable, resulting in a crisis of water quality and quantity. Therefore, studies on industrial wastewater purification and solar-driven seawater desalination based on wood composites have been widely considered as an important development direction. This paper comprehensively analyzes and summarizes the applications of wood composites in the fields of solar-driven seawater desalination and polluted water purification. In particular, the present situation of industrial wastewater containing heavy metal ions, microorganisms, aromatic dyes and oil stains and related problems of solar-driven seawater desalination are comprehensively analyzed and summarized. Generally, functional nanomaterials are loaded into the wood cell wall, from which lignin and hemicellulose are selectively removed. Alternatively, functional groups are modified on the basis of the molecular structure of the wood microchannels. Due to its three-dimensional (3D) pore structure and low thermal conductivity, wood is an ideal substrate material for industrial wastewater purification and solar-driven seawater desalination. Based on the study of objective conditions such as the preparation process, modification method and selection of photothermal conversion materials, the performances of the wood composites in filtration, adsorption and seawater desalination are analyzed in detail. In addition, this work points out the problems and possible solutions in applying wood composites to industrial wastewater purification and solar-driven seawater desalination.

Eco-Friendly Method for Wood Aerogel Preparation with Efficient Catalytic Reduction of 4-Nitrophenol

The advancement of science and technology and the growth of industry have led to an escalating discharge of domestic sewage and industrial wastewater containing dyes. This surge in volume not only incurs higher costs but also exacerbates environmental burdens. However, the benefits of green and reusable catalytic reduction materials within dye processes are still uncertain. Herein, this study utilized the eco-friendly deep eutectic solvent method (DESM) and the chlorite-alkali method (CAM) to prepare a cellulose-composed wood aerogel derived from natural wood for 4-nitrophenol (4-NP) reduction. The life cycle assessment of wood aerogel preparative process showed that the wood aerogel prepared by the one-step DESM method had fewer environmental impacts. The CAM method was used innovatively to make uniform the chemical functional groups of different wood species and various wood maturities. Subsequently, palladium nanoparticles (Pd NPs) were anchored in the skeleton structure of the wood aerogel with the native chemical groups used as a reducing agent to replace external reducing agents, which reduced secondary pollution and prevented the agglomeration of nanoparticles. Results showed that the catalytic reduction efficiency of 4-NP can reach 99.8%, which shows promises for applications in wastewater treatment containing dyes. Moreover, investigation of the advantages of preparation methods of wood aerogel has important implications for helping researchers and producers choose suitable preparation strategies according to demand.

Graphene oxide nanosheets immobilised on honeycomb pore structure of pomelo peel for enhanced removal of methylene blue

Herein, for the first time, a simple, green, direct immersion immobilisation method is reported for graphene oxide (GO) nanosheets using pomelo peel (PL) as a substrate. A GO/PL porous sponge was successfully prepared and used to remove methylene blue (MB) from dye wastewater. Considering the porosity, hydrophilicity and elasticity of the PL, the PL was placed in a GO aqueous suspension through direct immersion immobilisation. The carboxyl and hydroxyl groups in the peel could effectively capture and immobilise the GO nanosheets. GO was adsorbed into the PL pores and dispersed throughout the PL. Finally, the prepared super-hydrophilic and elastic GO/PL exhibited excellent adsorption performance towards MB in dye wastewater. The adsorption results revealed that the adsorption behaviour was consistent with the Langmuir isotherm and quasi-secondary kinetic models. The maximum equilibrium adsorption capacity of GO/PL towards MB was 124.2 mg/g, exceeding the values obtained for most of the previously reported adsorbents. Moreover, after five consecutive adsorption-desorption cycles, GO/PL retained 75% of its initial adsorption capacity. Mechanistic analysis revealed that pore filling, electrostatic attraction, ion exchange and hydrogen bonding interactions are the primary driving forces facilitating MB adsorption.

Sustainable approach to oil recovery from oil spills through superhydrophobic jute fabric

Ecosystems suffer from increased oil exploitation and frequent oil spills, which calls for effective, environment-friendly, and economically viable solutions. To address this, abandoned gunny sacks as the concerned jute fabric were superhydrophobically (water contact angle ∼159°) modified, incorporating titanium dioxide (TiO2) nanoparticles and hexadecyltrimethoxysilane (HDTMS), rendering a facile drop casting procedure. The modified superhydrophobic-superoleophilic jute fabric has been identified as a high-performance filter with superior reusability that can separate oil-water mixtures in challenging environmental conditions (including potent acidic, alkaline, highly saline, aqueous, frigid, and blistering water environments) while maintaining high separation efficiency. In continuation, static conditions indulging a batch and continuous oil separation performance and dynamic conditions stimulating turbulence in the oil-water mixture were proficiently carried out, mimicking real-world circumstances. As a result, the modified jute fabric has the advantages of high separation efficiency, stable recyclable properties, and outstanding durability, highlighting its enormous potential for use in practical applications.

Hydrophobic Carbon Nitride Nanolayer Enables High-Flux Oil/Water Separation with Photocatalytic Antifouling Ability

Efficient oil/water separation tackles various issues in occasions of oil leakage and oil discharge, such as environmental pollution, recollection of the oil, and saving the water. Herein, a compact superhydrophobic/superoleophilic graphitic carbon nitride nanolayer coated on carbon fiber networks (CNBA/CF) is designed and synthesized for efficient gravity-driven oil/water separation. The CNBA/CF shows excellent oil absorption and an impressive oil/water filtration separation performance. The flux reaches the state-of-art value of 4.29 × 105 L/m2/h for dichloromethane with separation efficiency up to 99%. Successive oil absorption tests, long-term filtration separation, and harsh conditions experiments confirm the remarkable separation and chemical structure stability of the CNBA/CF filter. Besides, the CNBA/CF demonstrates good photocatalytic antifouling ability thanks to the extended visible light absorption and improved charge separation. This work combines the material surface wettability modulation with a photocatalytic self-cleaning property in the fabrication of efficient oil/water separation materials while overcoming the filter fouling issue.

Composite Foams of the Graphitic Carbon Nitride@Carbon Nanofibrils Conferred a Superamphiphilic Property and Reinforced Thermal Stability

Herein, we demonstrated the preparation of novel three-dimensional (3D) superamphiphilic g-C3N4@carbon nanofibers foam (g-C3N4@CNFs) via a two-step approach: liquid nitrogen treatment-freeze-drying; the foams possessed good thermal stability. In this approach, melamine acted as a nitrogen source, and nanofibrillated cellulose (NFCs) functioned as a 3D skeleton. The thermal stability of the as-prepared g-C3N4@CNFs-3 foam was much higher than that of g-C3N4@CNFs-1, as indicated by thermogravimetric data, including an increase of the onset weight loss point (Tonset) by 238.6 °C and an improvement of the maximal weight loss rate (Tmax) by 258.8 °C. The combination of g-C3N4 with CNFs conferred a reduction in the heat release rate (ca. -86%) and the total heat release (ca. -75%). Furthermore, the composition of the hydrophilically oxygenated functional groups and hydrophobic triazine domains in g-C3N4@CNFs rendered it a unique amphiphilic property (contact angle close to 0° within 1.0 s for water and 0° within 12 ms for hexane). A high storage capacity for water and various organic solvents of the superamphiphilic g-C3N4@CNFs foam was found, up to 40-50 times its original weight. The discovery of these superamphiphilic foams is of great significance for the development of superwetting materials and may find their applications in oil emulsion purification and catalyst support fields.

Constructing A Solar Evaporator by Stacking Exhausted Wood Sponges for Freshwater Generation and Fertilizer Recovery

Solar water evaporation is an efficient and sustainable technology. To reduce energy consumption and improve cost efficiency, the surface modification of wood sponge by polypyrrole-glutathione (PGWS) was achieved using an in-situ synthetic method. The PGWS exhibits excellent adsorption efficiency for Hg(II) ions with adsorption capacity of 330.8 mg g-1 at 25 °C. Following Hg(II) absorption, the PGWS could be upcycled for solar steam generation. A stackable device was constructed by placing two wood sponges under a Hg(II) saturated PGWS [PGWS-Hg(II)], this system exhibited the highest water evaporation rate of 2.14 kg m-2  h-1 under 1 kW m-2 . Moreover, collecting paper was inserted between the stacked PGWS-Hg(II) and wood sponge for the collection of salts. As such salt can be successfully collected from simulated fertilizer plant effluent and then used as a nutrient for growing plants using a hydroponic system. The facile design of stackable evaporation provides an opportunity for wastewater utilization by harvesting solar energy.

Reusable, Stable, Efficient and Multifunctional Superhydrophobic and Oleophilic Polyurethane Sponge for Oil-Water Separation Prepared Using Discarded Composite Insulator

Oil spills and chemical leakages are a serious source of pollution in oceans and rivers, and have attracted worldwide attention. Many scientists are currently engaged in the development of oil-water separation technology. In this study, the umbrella skirt of a discarded silicone rubber insulator was utilized as feedstock, and polydimethylsiloxane (PDMS) was employed to immobilize the prepared powder (FXBW) onto a polyurethane (PU) sponge skeleton. Without any modifications using chemical reagents, a novel oil-water separation material, FXBW-PU, was developed, with a water contact angle of 155.3°. The FXBW-PU sponge exhibited an absorption capacity ranging from 11.79 to 26.59 g/g for various oils and organic solvents, while maintaining an excellent selective adsorption performance, even after undergoing ten compression cycles, due to its exceptional chemical and mechanical stability. With the assistance of a vacuum pump, the FXBW-PU sponge was utilized in a continuous separation apparatus, resulting in a separation efficiency exceeding 98.6% for various oils and organic solvents. The separation efficiency of n-hexane remains as high as 99.2% even after 10 consecutive separation cycles. Notably, the FXBW-PU sponge also separated the dichloromethane-in-water emulsions, which achieved the effect of purifying water. In summary, FXBW-PU sponge has great potential in the field of cleaning up oil/organic solvent contamination due to its low preparation cost, environmental friendliness and excellent performance.

From Forces to Assemblies: van der Waals Forces-Driven Assemblies in Anisotropic Quasi-2D Graphene and Quasi-1D Nanocellulose Heterointerfaces towards Quasi-3D Nanoarchitecture

In the pursuit of advanced functional materials, the role of low-dimensional van der Waals (vdW) heterointerfaces has recently ignited noteworthy scientific interest, particularly in assemblies that incorporate quasi-2D graphene and quasi-1D nanocellulose derivatives. The growing interest predominantly stems from the potential to fabricate distinct genres of quasi-2D/1D nanoarchitecture governed by vdW forces. Despite the possibilities, the inherent properties of these nanoscale entities are limited by in-plane covalent bonding and the existence of dangling π-bonds, constraints that inhibit emergent behavior at heterointerfaces. An innovative response to these limitations proposes a mechanism that binds multilayered quasi-2D nanosheets with quasi-1D nanochains, capitalizing on out-of-plane non-covalent interactions. The approach facilitates the generation of dangling bond-free iso-surfaces and promotes the functionalization of multilayered materials with exceptional properties. However, a gap still persists in understanding transition and alignment mechanisms in disordered multilayered structures, despite the extensive exploration of monolayer and asymmetric bilayer arrangements. In this perspective, we comprehensively review the sophisticated aspects of multidimensional vdW heterointerfaces composed of quasi-2D/1D graphene and nanocellulose derivatives. Further, we discuss the profound impacts of anisotropy nature and geometric configurations, including in-plane and out-of-plane dynamics on multiscale vdW heterointerfaces. Ultimately, we shed light on the emerging prospects and challenges linked to constructing advanced functional materials in the burgeoning domain of quasi-3D nanoarchitecture.

Lamellar Wood Sponge with Vertically Aligned Channels for Highly Efficient and Salt-Resistant Solar Desalination

Solar-assisted interfacial evaporation is a promising approach for purifying and desalinating water. As a sustainable biomass material, wood has attracted increasing interest as an innovative substrate for solar desalination, owing to its intrinsic porous structure, high hydrophilicity, and low thermal conductivity. However, developing wood-based solar evaporators with high evaporation rates and excellent salt resistance still remains a significant challenge, owing to the absence of large pores with high interconnectivity in natural wood. Herein, by converting the honeycombed structure of natural wood into a lamellar architecture via structural engineering, we develop a flexible wood sponge with vertically aligned channels for efficient and salt-resistant solar desalination after surface coating with carbon nanotubes (CNTs). The special lamellar structure with an interlayer distance of 50-300 μm provides the wood sponge with faster water transport, lower thermal conductivity, and water evaporation enthalpy, thus achieving higher evaporation performances in comparison with the cellular structure of natural wood. Noteworthy, the vertically aligned channels of the wood sponge facilitate sufficient fluid convection and diffusion and enable efficient salt exchanges between the heating interface and the underlying bulk water, thus preventing salt accumulation on the surface. Benefiting from the distinctive lamellar structure, the developed wood-sponge evaporator exhibits exceptional salt resistance even in a hypersaline brine (20 wt %) during continuous 7-day desalination under 1 sun irradiation, with a high evaporation rate (1.38-1.43 kg m-2 h-1), outperforming most previously reported wood-based evaporators. The lamellar wood sponge may provide a promising strategy for desalinating high-salinity brines in an efficient manner.

Thermal Insulation Mechanism, Preparation, and Modification of Nanocellulose Aerogels: A Review

Energy problems have become increasingly prominent. The use of thermal insulation materials is an effective measure to save energy. As an efficient energy-saving material, nanocellulose aerogels have broad application prospects. However, nanocellulose aerogels have problems such as poor mechanical properties, high flammability, and they easily absorbs water from the environment. These defects restrict their thermal insulation performance and severely limit their application. This review analyzes the thermal insulation mechanism of nanocellulose aerogels and summarizes the methods of preparing them from biomass raw materials. In addition, aiming at the inherent defects of nanocellulose aerogels, this review focuses on the methods used to improve their mechanical properties, flame retardancy, and hydrophobicity in order to prepare high-performance thermal insulation materials in line with the concept of sustainable development, thereby promoting energy conservation, rational use, and expanding the application of nanocellulose aerogels.

A sustainable layered nanofiber/sheet aerogels enabling repeated life cycles for effective oil/water separation

Discarded oil-containing absorbents, which has been used in handling oil spills, are tricky to deal with and have rose global environmental concerns regarding release of microplastics. Herein, we developed a facile strategy to fabricate sustainable absorbents by a gas-inflating method, through which 2D electrospinning polycaprolactone nanofiber membranes were directly inflated into highly porous 3D nanofiber/sheet aerogels with layered long fiber structure. The membranes were inflated rapidly from a baseline porosity of 81.98% into 97.36-99.42% in 10-60 min. The obtained aerogels were further wrapped with -CH₃ ended siloxane structures using CH₃SiCl₃. This hydrophobic absorbent (CA ≈ 145°) could rapidly trap oils from water with sorption range of 25.60-42.13 g/g and be recycled by simple squeeze due to its mechanical robustness. As-prepared aerogels also showed high separation efficiency to separate oils from both oil/water mixtures and oil-in-water emulsions (>96.4%). Interestingly, the oil-loaded absorbent after cleaning with absolute ethanol could be re-dissolved in selected solvents and promptly reconstituted by re-electrospinning and gas-inflation. The reconstituted aerogels were used as fire-new oil absorbents for repeated life cycles. The novel design, low cost and sustainability of the absorbent provides an efficient and environmentally-friendly solution for handling oil spills.

Advancing hyper-crosslinked materials with high efficiency and reusability for oil spill response

Developing materials with high efficiency for recovering oil to mitigate the environmental impact of oil spills has always been a challenging task. A commercial melamine formaldehyde sponge was coated with an optimised superhydrophobic/superoleophilic hyper-crosslinked polymer and applied to the removal of crude oil from oil-in-water emulsions for the improvement of oil spill clean-up processes. The high surface area, porosity, hydrophobicity, and selectivity of oil over water made the hyper-crosslinked polymer coated sponge (HPCS) an ideal sorbent for efficient oil/water separation. The system was able to strip crude oil from water emulsions of 1000 ppm to a negligible level of 2 ppm oil with minimal amounts of the HPCS material. More importantly, the HPCS material could be reused via a simple mechanical compression process, and the uptake capacity was retained over ten cycles. For five cycles of oil adsorption/mechanical compression the HPCS was able to provide water filtrate with oil concentrations of under 15 ppm. This is an effective and economical recovery system, removing the need for consistent solvent washing and drying processes. These results suggest that the HPCS is a promising material for oil/water separation and recovery under challenging conditions.

A comprehensive review of lignocellulosic biomass derived materials for water/oil separation

With rapid socioeconomic development, oil is widely used in all aspects of modern society. However, the extraction, transport, and processing of oil inevitably lead to the production of large quantities of oily wastewater. Traditional oil/water separation strategies are often inefficient, costly, and cumbersome to operate. Therefore, new green, low-cost, and high-efficiency materials must be developed for oil/water separation. As widely sourced and renewable natural biocomposites, wood-based materials have become a hot field recently. This review will focus on the application of several wood-based materials in oil/water separation. The state of research on wood sponges, cotton fibers, cellulose aerogels, cellulose membranes, and some other wood-based materials for oil/water separation over the last few years and provide an outlook on their future development are summarized and investigated. It is expected to provide some direction for future research on the use of wood-based materials in oil/water separation.

Robust, Fire-Retardant, and Water-Resistant Wood/Polyimide Composite Aerogels with a Hierarchical Pore Structure for Thermal Insulation

The use of energy-saving materials is an effective strategy for decreasing energy consumption and carbon emission. Wood is a type of biomass material with a natural hierarchical structure, which results in its high thermal insulation. It has been widely used in construction. However, developing wood-based materials without flammability and dimensional instability is still a challenge. Herein, we developed a wood/polyimide composite aerogel with a well-preserved hierarchical pore structure and dense hydrogen bonds inside, resulting in its excellent chemical compatibility and strong interfacial interactions between its two components. This novel wood-based composite was fabricated by removing most hemicellulose and lignin from natural wood, followed by the fast impregnation using an 'in situ gel' process. The introduction of polyimide into delignified wood substantially improved its mechanical properties, with the compression resistance being improved by over five times. Notably, the thermal conductivity coefficient of the developed composite was approximately half that of natural wood. Furthermore, the composite exhibited excellent fire-retardancy, hydrophobicity, thermal insulation, and mechanical properties. This study provides a novel method for wood modification, which not only aids interfacial compatibility between wood and polyimide but also retains the properties of the two components. The developed composite can effectively reduce energy consumption, making it promising for practical and complex thermal insulation applications.

Highly cross-linked carbon tube aerogels with enhanced elasticity and fatigue resistance

Carbon aerogels are elastic, mechanically robust and fatigue resistant and are known for their promising applications in the fields of soft robotics, pressure sensors etc. However, these aerogels are generally fragile and/or easily deformable, which limits their applications. Here, we report a synthesis strategy for fabricating highly compressible and fatigue-resistant aerogels by assembling interconnected carbon tubes. The carbon tube aerogels demonstrate near-zero Poisson's ratio, exhibit a maximum strength over 20 MPa and a completely recoverable strain up to 99%. They show high fatigue resistance (less than 1.5% permanent degradation after 1000 cycles at 99% strain) and are thermally stable up to 2500 °C in an Ar atmosphere. Additionally, they possess tunable conductivity and electromagnetic shielding. The combined mechanical and multi-functional properties offer an attractive material for the use in harsh environments.

Rational Design of Cellulosic Triboelectric Materials for Self-Powered Wearable Electronics

With the rapid development of the Internet of Things and flexible electronic technologies, there is a growing demand for wireless, sustainable, multifunctional, and independently operating self-powered wearable devices. Nevertheless, structural flexibility, long operating time, and wearing comfort have become key requirements for the widespread adoption of wearable electronics. Triboelectric nanogenerators as a distributed energy harvesting technology have great potential for application development in wearable sensing. Compared with rigid electronics, cellulosic self-powered wearable electronics have significant advantages in terms of flexibility, breathability, and functionality. In this paper, the research progress of advanced cellulosic triboelectric materials for self-powered wearable electronics is reviewed. The interfacial characteristics of cellulose are introduced from the top-down, bottom-up, and interfacial characteristics of the composite material preparation process. Meanwhile, the modulation strategies of triboelectric properties of cellulosic triboelectric materials are presented. Furthermore, the design strategies of triboelectric materials such as surface functionalization, interfacial structure design, and vacuum-assisted self-assembly are systematically discussed. In particular, cellulosic self-powered wearable electronics in the fields of human energy harvesting, tactile sensing, health monitoring, human-machine interaction, and intelligent fire warning are outlined in detail. Finally, the current challenges and future development directions of cellulosic triboelectric materials for self-powered wearable electronics are discussed.

Inspired by Wood: Thick Electrodes for Supercapacitors

The emergence and development of thick electrodes provide an efficient way for the high-energy-density supercapacitor design. Wood is a kind of biomass material with porous hierarchical structure, which has the characteristics of a straight channel, uniform pore structure, good mechanical strength, and easy processing. The wood-inspired low-tortuosity and vertically aligned channel architecture are highly suitable for the construction of thick electrochemical supcapacitor electrodes with high energy densities. This review summarizes the design concepts and processing parameters of thick electrode supercapacitors inspired by natural woods, including wood-based pore structural design regulation, electric double layer capacitances (EDLCs)/pseudocapacitance construction, and electrical conductivity optimization. In addition, the optimization strategies for preparing thick electrodes with wood-like structures (e.g., 3D printing, freeze-drying, and aligned-low tortuosity channels) are also discussed in detail. Further, this review presents current challenges and future trends in the design of thick electrodes for supercapacitors with wood-inspired pore structures. As a guideline, the brilliant blueprint optimization will promote sustainable development of wood-inspired structure design for thick electrodes and broaden the application scopes.

Facile, green and scalable preparation of low-cost PET-PVDF felts for oil absorption and oil/water separation

3D felt materials with pore structures have the advantages of high absorption performance and recyclability in oily wastewater treatment and chemical leakage. However, most of them were fabricated using either toxic organic solvents or complicated procedures. Herein, we report a facile, green, and scalable route for the fabrication of 3D composite felts with large pore structures by sequentially stirring and heating polyethylene terephthalate (PET) fibers and polyvinylidene fluoride (PVDF). The resulting PET-PVDF felt exhibits high oil absorption capacity to a variety of oil and organic solvents with a maximum saturated absorption capacity of 32 g/g. Additionally, it can be used to separate oil/water mixtures with a separation efficiency of 99.9% and separation flux of 89570 L m^-2 h^-1. Moreover, this felt shows excellent mechanical durability and chemical stability under acid, base, salt solution, and other harsh environments. The current study provides a promising approach for large-scale industrial oily wastewater separation.

Facile fabrication of solar-heating and Joule-heating hyperelastic MXene-modified sponge for fast all-weather clean-up of viscous crude oil spill

Developing rational sorbent for viscous crude oil clean-up is still a daunting challenge, which requires rapid oil-uptake capability and scalable fabrication process. Herein, a heatable hydrophobic sponge sorbent (H-MXene/PVA/MS) with excellent light/Joule-heating performances was fabricated by a simple and feasible top-down approach. MXene nanosheets firmly coated on the substrate skeleton gave the sorbent outstanding ability to convert solar/electricity into heat rapidly due to the localized surface plasmon resonance (LSPR) effect and ultrahigh metallic conductivity. The surface temperature of H-MXene/PVA/MS could reach about 80 ℃ under 1.0 sun irradiation within 30 s and 125 ℃ under a low applying voltage of 6 V within 25 s. The rapid and sufficient heat generation on the sorbent would effectively warm the surrounding oil and accelerate its absorption. The oil absorption rate under 1.0 sun irradiation (1 kW/m²) improved about 41.5 times compared to the unheated sorbent. Moreover, the sorbent showed practical application potential in harsh environments due to its high coating firmness, durability, elasticity, and suitability for large-scale production and operations. Thus, the easily-prepared H-MXene/PVA/MS sorbent, which mainly focuses on solar-heating, supplemented by Joule-heating, provides an efficient and energy-efficient strategy for addressing large-scale viscous oil spill clean-up.

Cleanup of oils and organic solvents from contaminated water by biomass-based aerogel with adjustable compression elasticity

Leakage of oils and organic solvents poses a significant threat to aquatic environments. Here, low-temperature carbonized aerogels with highly porous and anisotropic structures obtained only from biomass-derived materials were proposed to absorb polymorphic oils from contaminated water. Specifically, carbonized aerogels prepared at temperatures of 300 °C and 350 °C exhibited ultra-high absorption capacities (40‒125 g g^-1) and oil-water separation efficiencies (> 99%) even in harsh environments, which were attributed to their exceptional properties, including high porosity, abundant macropores, excellent thermal stability, and hydrophobicity. Through citric acid crosslinking and low-temperature carbonization, the aerogels exhibited superior compression elasticity and could be cyclically utilized through simple extrusion while realizing the recovery of oils. Moreover, the outstanding photothermal conversion properties obtained through carbonization contributed to the high temperature and fluidity of the oils surrounding the aerogels, which is crucial for improving the absorption performance of high-viscosity oils. Such absorbent materials are used to separate crude oil from oil-water mixtures, which can achieve maximum absorption of 56 g g^-1 and increase the absorption rate (from several days to 10 min) in a low-temperature (4 °C) seawater environment.

Strong, flexible and UV-shielding composite polyvinyl alcohol films with wood cellulose skeleton and lignin nanoparticles

The development of high-performance composite films using biomass materials have become a sought-after direction. Herein, a green method to fabricate strong, flexible and UV-shielding biological composite film from wood cellulose skeleton (WCS), lignin nanoparticles (LNPs) and polyvinyl alcohol (PVA) was described. In the work, WCS and LNPs were prepared by chemical treatment of wood veneer and Enzymatic lignin, respectively. Then, WCS was infiltrated with the LNPs/PVA mixtures and dried to obtain composite films. WCS enhanced the mechanical properties of the composite films, the tensile stress reached to 85.8 MPa and the tensile strain reached to 6.39 %. The composite films with LNPs blocked over 98 % of UV-light, the water absorption decreased by 30 %, and the thermal stabilities were also improved. These findings would provide some references for exploring high quality biological composite films.