Sonochemistry in environmental remediation. 1. Combinative and hybrid sonophotochemical oxidation processes for the treatment of pollutants in water

Ultrasound‒induced facile synthesis of spinel CoFe2O4‒PAC magnetic nanocatalyst for remediation of hypersaline petrochemical wastewater: Degradation mechanism, biodegradability enhancement and phytotoxicity mitigation

In this study, magnetic CoFe2O4-PAC nanocatalysts were synthesized through facile hydrothermal and co‒precipitation approaches with ultrasonic irradiation, which were used for the treatment of hypersaline petrochemical wastewater (HPCW). When an ultrasound‒induced synthesis process (US@CoFe2O4‒PAC) was used, a more efficient and stable magnetic spinel CoFe2O4‒PAC nanocatalyst was developed. The application of this nanocatalyst as a PMS activator, not only caused eradication of 90.4% of chemical oxygen demand (COD) of a HPCW after 90 min reaction time under the optimum conditions (pH 5-6, catalyst dose 1.0 g/L and 1.0 mM PMS), but also led to marginal leaching of iron (314 μg/L) and cobalt (95 μg/L) from the nanocatalyst. Recycling experiments over five consecutive runs showed a negligible decrease (7.2%) in COD removal efficiency which proved the stability and reusability of magnetic US@CoFe2O4-PAC. Two main mechanisms of adsorption and catalytic oxidation processes (homogeneous and heterogeneous PMS) are involved simultaneously in the PMS/US@CoFe2O4-PAC system, which are responsible for the destruction of refractory contaminants of HPCW through the generation of SO4•‒ and OH• radicals. COD of HPCW was mainly removed through SO4•- radical attack (73.6%) and the biodegradability of HPCW was enhanced dramatically after 90 min reaction time. The germination index (GI) of raw HPCW was increased 17.1 ± 4.2% and 24.3 ± 8.8% after 15 and 90 min reaction time, respectively, even PMS/US@CoFe2O4-PAC system showed less impact on phytotoxicity mitigation. Hence, it can be recommended to dilute the effluent before using for irrigational purpose. The findings of this study present practical significance of spinel US@CoFe2O4-PAC, which is an environment‒friendly catalyst, easy to handle and can sustain long‒term operation for the treatment of recalcitrant hypersaline wastewater and the other potential practical applications.

Graphene-based photocatalysts for degradation of organic pollution

Compared with the traditional wastewater treatment technology, semiconductor photocatalysis is a rapidly emerging environment-friendly and efficient Advanced Oxidation Process for degradation of refractory organic contaminants. Single-component semiconductor photocatalysts exhibit poor photocatalytic performance and cannot meet the requirements of wastewater treatment. The combination of semiconductor photocatalysts and Graphene can effectively improve the photocatalytic activity and stability of semiconductor photocatalysts. This review focuses on the synergistic effect of several types of semiconductors with Graphene for photocatalytic degradation of organic pollutants. After a brief introduction of the photodegradation mechanism of semiconductor materials and the basic description of Graphene, the synthesis, characterization and degradation performance of various Graphene-based semiconductor photocatalysts are emphatically introduced.

Study of heat and mass transfer processes during extraction of plant raw materials under the influence of ultrasound

Theoretical analysis of the process of biologically active substances (BAS) extraction from plant raw materials in conditions of ultrasonic action and without it to describe the kinetics of the process has been conducted. A mathematical model of the process of BAS extraction from plant raw materials to establish the dependence of changes in the concentration of BAS in the volume of cells in the intercellular space and in the main volume of the extractant has been developed. On the basis of the solution of the mathematical model the duration of the model of BAS extraction process from plant raw materials has been established, results show that the duration of the process of extraction of oil from plant raw materials in an acoustic extractor decreases by 1.5 times ultrasonic extraction can be used for the extraction of biologically active substances, such as essential oils, lipids and dietary supplements from plants.

Remediation of environmentally persistent organic pollutants (POPs) by persulfates oxidation system (PS): A review

Over the past few years, persistent organic pollutants (POPs) exhibiting high ecotoxicity have been widely detected in the environment. Persulfate-oxidation hybrid system is one of the most widely used novel advanced oxidation techniques and is based on the persulfate generation of SO₄^-∙ and ∙OH from persulfate to degrade POPs. The overarching aim of this work is to provide a critical review of the variety of methods of peroxide activation (e.g., light activated persulfate, heat-activated persulfate, ultrasound-activated persulfate, electrochemically-activated persulfate, base-activated persulfate, transition metal activated persulfate, as well as Carbon based material activated persulfate). Specifically, through this article we make an attempt to provide the important characteristics and uses of main activated PS methods, as well as the prevailing mechanisms of activated PS to degrade organic pollutants in water. Finally, the advantages and disadvantages of each activation method are analyzed. This work clearly illustrates the benefits of different persulfate activation technologies, and explores persulfate activation in terms of Sustainable Development Goals, technical feasibility, toxicity assessment, and economics to facilitate the large-scale application of persulfate technologies. It also discusses how to choose the most suitable activation method to degrade different types of POPs, filling the research gap in this area and providing better guidance for future research and engineering applications of persulfates.

Mechanisms and product toxicity of activated carbon/peracetic acid for degradation of sulfamethoxazole: implications for groundwater remediation

Carbon-based materials activated peracetic acid (PAA) to repair groundwater is an environmentally friendly and low-cost technology to overcome secondary pollution problems. In this study, thermally modified activated carbon (AC600) was applied to activate PAA to degrade sulfamethoxazole (SMX). And the effect of groundwater pH, chloride ion (Cl^-), bicarbonate (HCO₃^-), sulfate ion (SO₄^2-), and natural organic matter (NOM) on SMX removal by AC600/PAA process was studied in detail. PAA could be effectively activated by AC600. Increasing AC600 dose (10-100mg/L) or PAA dosages (0.065-0.39 mM) generally enhanced the SMX removal, the excellent performance in SMX removal was achieved at 50 mg/L AC600 and 0.26 mM PAA. The removal of SMX was well-described by second-order kinetic, with the rate constant (k_obs) of 10.79 M^-1s^-1, both much greater than the removal constants of PAA alone (0.034 M^-1s^-1) and AC600 alone (1.774 M^-1s^-1). R-O·(CH₃C(O)OO·, CH₃C(O)O·) and electron-transfer process were proved to be responsible for the removal of SMX while HO· and ¹O₂ made little to no contribution to the novel PAA/AC600 system, which differs from typical advanced oxidation processes. The SMX can be removed effectively over a wide pH range (3-9), exhibiting a remarkable pH-tolerant performance. Sulfate ion (SO₄^2-), dissolved oxygen (DO), NOM displayed negligible influence on the SMX removal. Bicarbonate (HCO₃^-) exerted an inhibitory effect on SMX abatement, while chloride ion (Cl^-) promoted the removal of SMX. This showed excellent anti-interference capacity and satisfactory decontamination performance under actual groundwater conditions. Furthermore, the degradation pathways of SMX were proposed, there was no obvious difference in the acute toxicity of the mixed products during the degradation process. It will facilitate further research of metal-free catalyst/PAA system as a new strategy for groundwater in-situ remediation technology.

Conformational analysis and concentration detection of linuron: Spectroscopic NMR and SERS study

Linuron is a commonly used organic herbicide which is used in plant growth control. Due to its potential health concerns, the characterization and monitoring of linuron have been a subject of several studies. In this work, we employed nuclear magnetic resonance (NMR) and Raman spectroscopic techniques supported with the density functional theory (DFT) to investigate the conformational behavior and electronic aspects of linuron. The selective nuclear Overhauser effect (SelNOE) spectra confirmed that linuron exists predominantly in the anti configuration and is facilitated with a weak intramolecular hydrogen bonding between the acidic amide proton and oxygen of methoxy moiety. Quantum chemical results showed that the corresponding syn form of the molecule is 8.5 kcal/mol less stable. Further, the surface enhanced Raman scattering (SERS) technique using gold nanoparticles (AuNPs) was implemented as a potential spectroscopic protocol for the concentration monitoring of trace linuron. The Raman responses of four vibrational modes, namely CC stretching, CN stretching, N-H rocking and ring deformation, were successfully enhanced with an excellent linear concentration-intensity dependency. The aromatic CC stretching vibration at 1595 cm^-1 in the Raman spectra has demonstrated the highest enhancement factor (6.5 × 10⁴) and the lowest limit of detection (10^-7 M). The interaction of linuron with the gold nanocluster was simulated by establishing a simple DFT model which predicted that the most pronounced binding with the gold atom takes place at the benzene ring.

Treatment of slaughterhouse wastewater using high-frequency ultrasound: optimization of operating conditions by RSM

Slaughterhouse processes produce substantial amounts of high organic strength wastewater due to high COD level. A fundamental work had been carried out to explore the removal of COD from actual poultry slaughterhouse wastewater by ultrasound irradiation. The effect of applied frequency, power density, irradiation time, pH, and adding H₂O₂ on COD removal was investigated. The COD removal reached ultimate levels after irradiation time of 180 min. The COD removal percentage increased from 2% to 43% and from 2% to 49% when the power density increased from 160 to 1200 W/L at working frequencies of 1142 and 578 kHz, respectively. Increasing the pH from 7 to 9 reduced the COD removal from 51% to 13%. At low power densities, the high frequency (1142 kHz) was more efficient in COD removal than low frequency (578 kHz) and vice versa at high power densities. A combined system of US and H₂O₂ was more effective in removing COD than US standalone system. Finally, the kinetics of the COD decay using sonication was found to obey the first-order model. In conclusion, the US can be used efficiently at least to pretreat slaughterhouse wastewater with a COD removal of about 50%.

Recovery of Zn and Ge from zinc oxide dust by ultrasonic-H2O2 enhanced oxidation leaching

Zn and Ge were selectively extracted from zinc oxide dust (ZOD) by the ultrasonic-H₂O₂ (UH) combined oxidation-leaching process. In the leaching process, the effects of the dosage of H₂O₂ (6–29.5 mL), ultrasonic power, initial acidity (100–200 g L⁻¹), liquid/solid mass ratio (4–8 : 1), leaching temperature (50–90 °C), and leaching time (30–240 min) on the leaching rates of Zn and Ge were studied. The experimental results showed that the ultrasonic power and the dosage of H₂O₂ have the greatest influence on the leaching rates of Zn and Ge. The results showed the optimum conditions as: ultrasonic power 200 W, the dosage of H₂O₂ 14.8 mL, initial acidity 160 g L⁻¹, liquid/solid mass ratio 7 : 1, leaching time 60 min, stirring speed 400 rpm, leaching temperature 60 °C, and the leaching rate of Zn and Ge reaches 99.61% and 88.29%, respectively. The leaching rates of Zn and Ge by UH were 7.86% and 5.65% higher than that by conventional leaching (CL), respectively. The experimental results showed that UH leaching technology can improve the rates of Zn and Ge from ZOD, reduce the leaching temperature, save the production cost, solve the problem of low leaching rates of Zn and Ge in ZOD treatment technology, and realize the resource, reduction and harmless treatment of ZOD.

Zn and Ge were selectively extracted from zinc oxide dust (ZOD) by the ultrasonic-H₂O₂ (UH) combined oxidation-leaching process.

Instantaneous Sonophotocatalytic Degradation of Tetracycline over NU-1000@ZnIn2S4 Core-Shell Nanorods as a Robust and Eco-friendly Catalyst

The universal pollution of diverse water bodies and declined water quality represent very important environmental problems. The development of new and efficient photocatalytic water treatment systems based on the Z-scheme mechanisms can contribute to tackling such problems. This study reports the preparation, full characterization, and detailed sonophotocatalytic activity of a new series of hybrid NU@ZIS nanocomposites, which comprise a p-n heterojunction of 3D Zr(IV) metal-organic framework nanorods (NU-1000) and photoactive ZnIn₂S₄ (ZIS) nanostars. Among the obtained materials with varying content of ZIS (5, 10, 20, and 30%) on the surface of NU-1000, the NU@ZIS20 nanocomposite revealed an ultrahigh catalytic performance and recyclability in a quick visible-light-induced degradation of the tetracycline antibiotic in water under sonophotocatalytic conditions. Moreover, increased activity of NU@ZIS20 can be ascribed to the formation of a p-n heterojunction between NU-1000 and ZIS, and a synergistic effect of these components, leading to a high level of radical production, facilitating a Z-scheme charge carrier transfer and reducing the recombination of charge carriers. The radical trapping tests revealed that ^•OH, ^•O₂^-, and h⁺ are the major active species in the sonophotocatalytic degradation of tetracycline. Possible mechanism and mineralization pathways were introduced. Cytotoxicity of NU@ZIS20 and aquatic toxicity of water samples after tetracycline degradation were also assessed, showing good biocompatibility of the catalyst and efficacy of sonophotocatalytic protocols to produce water that does not affect the growth of bacteria. Finally, the obtained nanocomposites and developed photocatalytic processes can represent an interesting approach toward diverse environmental applications in water remediation and the elimination of other types of organic pollutants.

Recent Advances in Fly-Ash-Based Geopolymers: Potential on the Utilization for Sustainable Environmental Remediation

This Mini-Review provides the fundamentals and the state-of-the-art overview on geopolymers, novel inorganic polymeric materials (also known as alkali-bounded ceramics), synthesized from aluminosilicate sources and explores their current and potential sustainable environmental applications. It summarizes and examines concisely the recent scientific advances on geopolymers widely synthesized from abundantly available fly-ash-based aluminosilicate materials via alkaline activation at relatively low temperatures. Although geopolymerization is not a new concept and has offered valuable solutions to some environmental challenges as a low-cost and environmentally benign alternative to conventional energy-intensive Portland cement-based construction materials and has also been used as a barrier in immobilizing toxic and radioactive metals, the application of this technology to produce effective adsorptive materials for mitigation of liquid- and gas-phase contaminants is relatively recent. The valorization of the fly-ash waste in the sustainable and cost-effective development of geopolymeric adsorbents and catalysts for the treatment and control of environmental contaminants and energy production and storage could lead to many economic benefits due to the low cost and resource recycling of this globally abundant raw material. Perspectives on the synthesis and utilization of new geopolymer-based adsorbents for environmental and energy applications with insights into future research directions, prospects, and challenges for economic large-scale production are addressed.

Acoustic frequency and optimum sonochemical production at single and multi-bubble scales: A modeling answer to the scaling dilemma

The present work consists of an innovative approach aiming to address the scalability dilemma of the sonochemical activity dependency of acoustic frequency. The study originates from the discordance of observations between the theoretical investigations of the sonochemical activity of the single acoustic cavitation bubble in function of the acoustic frequency, in one hand, and the experimental findings regarding the optimal frequency condition, mainly in terms of pollutant degradation, in the other hand. A single bubble and an up-scaled model of the sonochemical activity are suggested and simulations were conducted based on both of them over the frequencies 20, 200, 300, 360, 443, 500, 600 and 800 kHz under an oxygen atmosphere. The results reveal that the sonochemical production at single bubble scale is monotonously decreasing with the increase of frequency, while all the products demonstrate an absolute optimum of sonochemical production at 200 kHz, except HO^• that attains its maximum molar yield under 300 kHz. Besides, the production of the predominant species, namely HO₂^•, HO^• and O₃, manifests a clear rebound at 500 kHz. All the present results were compared to and confirmed by experimental findings, while the scalability of the concentrations of sonochemically produced species was discussed using a parameter we introduced as "the mass focusing factor".

Iminodiacetic acid-functionalized porous polymer for removal of toxic metal ions from water

The design of efficient adsorbent with abundant binding sites for heavy metal ions is crucial for developing innovative materials that will remove pollutant metal ions. The high uptake capacity, kinetics, and affinity towards the toxic metals are the key requirements that the materials under invesigation should accomplish. Here we report the synthesis of iminodiacetic acid-functionalized hypercrosslinked polymer (IDA-HCP) for purification of water polluted by toxic metal ions via coordination of carboxylate and amino active sites on the surface of porous polymer. The obtained porous polymer is stable under harsh conditions and the structural features on the polymer work together to help the removal of Pb(II) with 1138 mg g^-1 uptake capacity. In the meanwhile, the IDA-HCP reveals reuseability and very promising capture efficiency not only for Pb²⁺, but also for Hg²⁺ and Cd²⁺ from a mixture of Pb²⁺, Hg²⁺, Cd²⁺, Co²⁺, Fe³⁺, Zn²⁺, Mg²⁺, and Na⁺ metal ions. This result gives us confidence that the polymer material can solve the pollution problem caused by various metal ions.

Aldehyde Production as a Calibrant of Ultrasonic Power Delivery During Protein Misfolding Cyclic Amplification

The protein misfolding cyclic amplification (PMCA) technique employs repeated cycles of incubation and sonication to amplify minute amounts of misfolded protein conformers. Spontaneous (de novo) prion formation and ultrasonic power level represent two potentially interrelated sources of variation that frustrate attempts to replicate results from different laboratories. We previously established that water splitting during PMCA provides a radical-rich environment leading to oxidative damage to substrate molecules as well as the polypropylene PCR tubes used for sample containment. Here it is shown that the cross-linking agent formaldehyde is generated from buffer ions that are attacked by hydroxyl radicals. In addition, free radical damage to protein, nucleic acid, lipid, and detergent molecules produces a substantial concentration of aldehydes (hundreds of micromolar). The measurement of aldehydes using the Hantzsch reaction provides a reliable and inexpensive method for measuring the power delivered to individual PMCA samples, and for calibrating the power output characteristics of an individual sonicator. The proposed method may also be used to better account for inter-assay and inter-laboratory variation in prion replication and de novo prion generation, the latter of which may correlate with aldehyde-induced cross-linking of substrate molecules.

NOx attenuation in flue gas by •OH/SO4•--based advanced oxidation processes

The combustion of fossil fuels has resulted in rapidly increasing emissions of nitrogen oxide (NO_x), which has caused serious human health and environmental problems. NO capture has become a research focus in gas purification because NO accounts for more than 90% of NO_x and is difficult to remove. Advanced oxidation processes (AOPs), features the little secondary pollution and the broad-spectrum strong oxidation of hydroxyl radicals (^•OH), are effective and promising strategies for NO removal from coal-fired flue gas. This review provides the state of the art of NO removal by AOPs, highlighting several methods for producing ^•OH and SO₄^•-. According to the main radicals responsible for NO removal, these processes are classified into two categories: hydroxyl radical-based AOPs (HR-AOPs) and sulfate radical-based AOPs (SR-AOPs). This paper also reviews the mechanisms of NO capture by reactive oxygen species (ROS) and SO₄^•- in various AOPs. A HiGee (high-gravity) enhanced AOP process for improving NO removal, characterized by intensified gas-liquid mass transfer and efficient micro-mixing, is then proposed and discussed in brief. We believe that this review will be useful for workers in this field. Graphical abstract.

Synergistic, aqueous PAH degradation by ultrasonically-activated persulfate depends on bulk temperature and physicochemical parameters

Coupling ultrasound with other remediation technologies has potential to result in synergistic degradation of contaminants. In this work, we evaluated synergisms from adding high-power ultrasound (20 kHz; 250 W) to activated persulfate over a range of bulk temperatures (20-60 °C). We studied the aqueous degradation kinetics of three polycyclic aromatic hydrocarbons (PAHs: naphthalene, phenanthrene, and fluoranthene) treated by ultrasound-alone, heat-activated persulfate, and combined ultrasonically-activated persulfate (US-PS). At 20 °C, observed US-PS rate constants strongly correlated with Wilke-Chang diffusion coefficients. This correlation indicates PAH molecules diffuse to the bubble-water interface prior to reaction with sulfate radicals (SO₄^-) generated at the interface. At higher temperatures, observed US-PS rate constants appear to be a more complicated function of temperature and diffusion coefficients. Synergy indexes for PAHs with fast diffusion coefficients were greatest at 20 °C. Fluoranthene, the largest and most hydrophobic PAH, had a maximum synergy index at 30 °C; it benefited from additional thermal persulfate activation in bulk solution. Fluoranthene synergy indexes, however, decreased above 30 °C and became antagonistic at 60 °C. Electron paramagnetic resonance (EPR) spin trapping was used to quantify hydroxyl radical (OH) produced from acoustic cavitation in the absence of persulfate. These data showed consistent OH production from 20 to 60 °C, indicating PAH antagonisms at 60 °C were not due to lower bubble collapse temperatures. Instead, the results suggest that PAH antagonisms are caused by increased radical-radical recombination as bulk temperature increases. In effort to develop an efficient, combined remediation technology, this work suggests bulk temperatures between 20 and 40 °C maximize US-PS synergisms.

Dual-frequency ultrasound: Strengths and shortcomings to water treatment and disinfection

Since the early 2000s, dual-frequency ultrasound (DFUS) has received much attention for synergistically enhanced elimination of organic pollutants and pathogenic microorganisms from water. In the present review, we have surveyed recent developments in acoustic physics to elucidate the mechanism of synergistic effect under exposure of aqueous media to DFUS. Briefly, the nonlinear dynamics of microbubbles upon DFUS exposure produces additional frequencies, such as harmonics, subharmonics, ultraharmonics and combination frequencies. These increase the probability of bubbles collapse, thereby enhancing cavitation and generating more reactive oxygen species (ROS) for advanced oxidation processes (AOPs). Further, literature data on ROS generation, chemical degradation and microbial inactivation in aqueous media through DFUS alone and DFUS-based AOPs (involving oxidants or catalysts) have been discussed. In this regard, optimal frequency combination, sonoreactor type and transducer arrangement appear to be key parameters for achieving a high synergistic effect. Strengths and shortcomings of DFUS to water treatment and disinfection have been identified and future research directions have been proposed. Though most studies were conducted on pure (matrix-free) aqueous solutions, these AOPs could be applicable for treating real waters.

A critical review of the current technologies in wastewater treatment plants by using hydrodynamic cavitation process: principles and applications

In the last decade, hydrodynamic cavitation (HC) was increasingly used in the field of wastewater treatment. Due to its oxidative capability, HC was applied to treat aqueous effluents polluted by organic, toxic and bio-refractory contaminants, whereas its mechanical and chemical effects have allowed to disintegrate cells of microorganisms in biological applications. Due to their geometries, HC can be detected in some reactors, in which a variation of hydraulic parameters in the fluid such as flow pressure and flow velocity is induced. HC process involves the formation, growth, implosion and subsequent collapse of cavities, occurring in a very short period of time and releasing large magnitudes of power. In this paper, the vast literature on HC is critically reviewed, focusing on the basic principles behind it, in terms of process definition and analysis of governing mechanisms of both HC generation and pollutants degradation. The influence of various parameters on HC effectiveness was assessed, considering fluid properties, construction features of HC devices and technological aspects of processes. The synergetic effect of HC combined with chemicals or other techniques was discussed. An overview of the main devices used for HC generation and different existing methods to evaluate the cavitation effectiveness was provided. Knowledge buildup and optimization for such complex systems from mathematical modeling was highlighted.

Investigation of the Synergistic Effect of Sonolysis and Photocatalysis of Titanium Dioxide for Organic Dye Degradation

Herein, we report the effect of sonoluminescence and an initial dye concentration on the sonophotocatalysis of TiO2 for the degradation of eosin B, a textile dye. We first investigated the light illuminated during ultrasound irradiation (sonoluminescence) by photographic images, a radical indicator (luminol), and photoluminescence spectra of the detection range of 300–1050 nm. Next, we examined the synergistic effect of sonolysis on photocatalysis by comparing the dye degradation of sonophotocatalysis to that of individual contributions of sonolysis and photocatalysis. Since it was found that the synergist effect is highly engaged with a dye concentration and sonication power, we conducted the comparison test in different concentrations of eosin B (5 and 20 mg/L) and ultrasound powers (35.4, 106.1, and 176.8 W/cm2). When the concentration of dyes was low, negative synergistic effects were found at all ultrasound powers, whereas at the high concentration, positive synergistic effects were observed at high ultrasound power. This difference in synergistic effects was explained by the influence of ultrasound on dynamics of dye adsorption on the TiO2 surface.

Reaction kinetics of sonochemical oxidation of potassium hexacyanoferrate(II) in aqueous solutions

We studied sonochemical reactions resulting from ultrasonic treatment of potassium hexacyanoferrate(II) in aqueous solutions using a custom-built apparatus working at 536 kHz. We concluded that primary reactions are completely dominated by oxidation of Fe(II) to Fe(III) and did not find any evidences for degradation of cyanide. At the highest concentration used in the present study (0.1 M) we detected formation of pentacyanoaquaferrate(II) complex, which is most probably formed in reactions between hexacyanoferrate(III) anions and hydrogen atoms or hydrated electrons formed in sonochemical processes. We also determined that hydroxyl radicals formation rate in our system, (8.7 ± 1.5)∙10^-8 M∙s^-1, is relatively high compared to other reported experiments. We attribute this to focusing of the ultrasonic wave in the sample vessel. Finally, we suggest that oxidation rate of hexacyanoferrate(II) anions can be a convenient benchmark of efficiency of sonochemical reactors.

Optimization of ibuprofen degradation in water using high frequency ultrasound-assisted biological reactor

Ultrasound (US) is being considered as a promising emerging advanced oxidation process to degrade persistent organic-pollutants. This paper investigated the effect of several operating parameters on the degradation of a recalcitrant pharmaceutical product, namely ibuprofen (IBP), using an ultrasound-assisted biological reactor. The tested operating parameters are the power density (960, 480) W/L, US frequency (1,142, 860, 578) kHz, working volume (500, 250) mL, initial IBP concentration (30, 60) mg/L, and pH (8.2, 4). It was observed that the IBP degradation was directly influenced by the power density, and the highest degradation efficiency (99%) was obtained at 960 w/L. However, the degradation of IBP at sonication time of 120 min was found to increase from 39% to 96% while decreasing the US frequency from 1,142 to 578 kHz. The working volume had no clear effect on the IBP degradation. The optimal pH was found to be 4, which resulted in 99.5% IBP degradation efficiency after 120 min of sonication time. The degradation of IBP followed the first order kinetics. Finally, the sonically-treated water was fed to a subsequent aerobic biological reactor. The results revealed that the remaining chemical oxygen demand (COD) after sonication was lowered in the biological reactor by a percentage of 47%.

Neonicotinoids removal by associated binary, tertiary and quaternary advanced oxidation processes: Synergistic effects, kinetics and mineralization

The degradation of four representative neonicotinoids, namely Thiamethoxam, Imidacloprid, Acetamiprid and Thiacloprid, was carried out by the sequential association of different advanced oxidation processes, including Ozonation, Electro-chemical Oxidation, Ultrasound, Ultraviolet radiation, and their different possible associations. There are no published papers in the literature on the removal of this type of insecticides through these associated oxidation processes. Single oxidation processes did not achieve total pollutants removal in less than 3 h (only UV radiation treatment obtain a total removal of Thiamethoxan in 150 min, but with mineralization below 15% TOC). For double sequential processes, Electro-oxidation-Ozone treatment obtains a total removal of Imidacloprid in 120 min and an increase of mineralization to 50% TOC. Three or four sequential processes are recommended to improve degradation and mineralization rates in a significant way, Electro-oxidation-Ozone-UV treatment obtains a total removal of Thiamethoxan in 80 min with mineralization over 75% TOC. These results confirm important synergistic effects which were quantified. The global trend indicates that Thiamethoxam is the most oxidizable neonicotinoid, whereas Acetamiprid is the most recalcitrant compound. The degradation rate of each neonicotinoid followed pseudo-first-order kinetics and the different oxidation pathways were also quantified from a kinetic point of view.

Simultaneous NO and SO2 removal by aqueous persulfate activated by combined heat and Fe2+: experimental and kinetic mass transfer model studies

This study evaluates the chemistry, kinetics, and mass transfer aspects of the removal of NO and SO₂ simultaneously from flue gas induced by the combined heat and Fe²⁺ activation of aqueous persulfate. The work involves experimental studies and the development of a mathematical model utilizing a comprehensive reaction scheme for detailed process evaluation, and to validate the results of an experimental study at 30-70 °C, which demonstrated that both SO₂ and Fe²⁺ improved NO removal, while the SO₂ is almost completely removed. The model was used to correlate experimental data, predict reaction species and nitrogen-sulfur (N-S) product concentrations, to obtain new kinetic data, and to estimate mass transfer coefficient (K_La) for NO and SO₂ at different temperatures. The model percent conversion results appear to fit the data remarkably well for both NO and SO₂ in the temperature range of 30-70 °C. The conversions ranged from 43.2 to 76.5% and 98.9 to 98.1% for NO and SO₂, respectively, in the 30-70 °C range. The model predictions at the higher temperature of 90 °C were 90.0 and 97.4% for NO and SO₂, respectively. The model also predicted decrease in K_La for SO₂ of 1.097 × 10^-4 to 8.88 × 10^-5 s^-1 (30-90 °C) and decrease in K_La for NO of 4.79 × 10^-2 to 3.67 × 10^-2 s^-1 (30-50 °C) but increase of 4.36 × 10^-2 to 4.90 × 10^-2 s^-1 at higher temperatures (70-90 °C). This emerging sulfate-radical-based process could be applied to the treatment of flue gases from combustion sources. Graphical abstract.

Hybrid Advanced Oxidation Processes Involving Ultrasound: An Overview

Sonochemical oxidation of organic pollutants in an aqueous environment is considered to be a green process. This mode of degradation of organic pollutants in an aqueous environment is considered to render reputable outcomes in terms of minimal chemical utilization and no need of extreme physical conditions. Indiscriminate discharge of toxic organic pollutants in an aqueous environment by anthropogenic activities has posed major health implications for both human and aquatic lives. Hence, numerous research endeavours are in progress to improve the efficiency of degradation and mineralization of organic contaminants. Being an extensively used advanced oxidation process, ultrasonic irradiation can be utilized for complete mineralization of persistent organic pollutants by coupling/integrating it with homogeneous and heterogeneous photocatalytic processes. In this regard, scientists have reported on sonophotocatalysis as an effective strategy towards the degradation of many toxic environmental pollutants. The combined effect of sonolysis and photocatalysis has been proved to enhance the production of high reactive-free radicals in aqueous medium which aid in the complete mineralization of organic pollutants. In this manuscript, we provide an overview on the ultrasound-based hybrid technologies for the degradation of organic pollutants in an aqueous environment.

Cathode-Introduced Atomic H* for Fe(II)-Complex Regeneration to Effective Electro-Fenton Process at a Natural pH

Promotion of iron solubility using ligands is the preliminary step in the homogeneous electro-Fenton (EF) process at a mild pH, but the chelate efficiencies of most organic ligands are unsatisfactory, resulting in insufficient Fe(II) availability. In this study, atomic H* was, for the first time, introduced to the EF process to accelerate the regeneration of the Fe(II)-complex at a mild pH using a Ni-deposited carbon felt (Ni-CF) cathode. The introduction of atomic H* significantly elevated total organic carbon (TOC) abatement of ciprofloxacin (CIP) from 42% (CF) to 81% (Ni-CF) at a natural pH. In the presence of humic acids (HAs), atomic H* introduced via Ni-CF enhanced the CIP degradation rate to 10 times that of the CF at a mild pH. The electron spin resonance (ESR), density functional theory (DFT) calculations, electrochemical characterization, and in situ electrochemical Raman study clearly demonstrated that the atomic H* generated from the Ni-CF cathode was highly efficient at reducing Fe(III)-complexes at a natural pH. Additionally, the Ni-CF could generate atomic H* without significant nickel leaching. Thus, the atomic H* could continuously facilitate iron cycling and, consequently, enhance pollutant mineralization via the homogeneous EF process at a mild pH in an environmentally friendly manner.

Acoustic cavitation assisted plasma for wastewater treatment: Degradation of Rhodamine B in aqueous solution

A novel wastewater treatment process, acoustic cavitation assisted plasma (ACAP) is proposed in this study aiming at expanding the treatable range of water pollutants due to a synergetic effect of ultrasound irradiation and high voltage plasma discharge. In this process, the role of acoustic cavitation is not only to provide generation of chemically active OH radicals, as for example in conventional ultrasonic wastewater treatment techniques, but also to ensure conditions for stable plasma generation in wastewater and, thus, to extend the treatable range of water pollutants. Rhodamine B (RhB) was used as a model pollutant in experiments examining effects of ultrasound amplitude, RhB initial concentration, output voltage, solution pH and electrical conductivity on the RhB degradation efficiency. The results revealed that the ultrasound-assisted plasma generation requires lower output voltages and allows to increase the acceptable range of electrical conductivity of treatable solutions up to 1000 μS/cm, that is about 24 times higher than in the case of conventional plasma discharge treatment. The alkaline and acid medium were found to be favorable for higher degradation efficiency. Additional measurements and results of recent investigations concerning underwater plasma showed that microbubbles presented in cavitation zone could serve as "bridges" making the pulse discharge propagation between the electrodes easier than in the conventional case. Besides, acoustic cavitation assists a faster transition of plasma discharge from ineffective streamer type to more effective spark type that further contributes to the improvement of the treatment performance.

Fabrication of graphene-oxide/β-Bi2O3/TiO2/Bi2Ti2O7 heterojuncted nanocomposite and its sonocatalytic degradation for selected pharmaceuticals

A graphene-oxide (GO)/β-Bi₂O₃/TiO₂/Bi₂Ti₂O₇ heterojuncted nanocomposite, designated as GBT, was synthesized via a two-step hydrothermal process. The sonocatalytic activity of the GBT was evaluated at several frequencies (28, 580, and 970 kHz) and compared with Bi-doped GO (GB) and Ti-doped GO (GT). Transmission electron microscopy images showed heterojuncted crystal structures of Bi and Ti on GO, and X-ray diffraction patterns verified that the crystal structures consisted of β-Bi₂O₃, TiO₂, and Bi₂Ti₂O₇ nanocomposites. Energy-dispersive X-ray spectroscopy revealed a higher proportion of metal on GBT surfaces compared with GB and GT surfaces. The energy band gaps of GT, GB, and GBT were 3.0, 2.8, and 2.5 eV, respectively. Two pharmaceuticals (PhACs; carbamazepine [CBZ] and acetaminophen [ACE]) were selected and treated under sonolytic conditions at frequencies of 28, 580, and 970 kHz at a power level of 180 W L^-1. The selected pharmaceuticals, present at initial concentrations of 20 μM, were reduced by over 99% by ultrasonic irradiation in the presence of GBT. The 580 kHz treatment achieved the most rapid organic removal among the frequencies tested. The removal kinetic of CBZ was higher than that of ACE owing to its relatively high hydrophobicity. High sonocatalytic activity of GBT was observed through measurement of H₂O₂ in solution. Because of its low band gaps and high surface activity, GBT exhibited higher sonolytic activity in removing selected PhACs than GT or GB.

Use of ultrasound irradiation to inactivate Cryptosporidium parvum oocysts in effluents from municipal wastewater treatment plants

Water reuse is currently considered an innovative way to addressing water shortage that can provide significant economic, social and environmental benefits, particularly -but not exclusively- in water deficient areas. The potential transmission of infectious diseases is the most common concern in relation to water reclamation. Cryptosporidium is an important genus of protozoan enteropathogens that infect a wide range of vertebrate hosts, including humans. The infective form (oocyst) is highly resistant to the environmental conditions and disinfection treatments. Consequently, Cryptosporidium is the most common etiological agent identified in waterborne outbreaks attributed to parasitic protozoa worldwide. The present study evaluates the efficacy of ultrasound disinfection, at three power levels (60, 80 and 100 W), pulsed at 50% or in continuous mode, for inactivating the waterborne protozoan parasite Cryptosporidium parvum in simulated and real effluents from municipal wastewater treatment plants (MWTPs). Overall interpretation of the results shows that the application of ultrasound irradiation at 80 W power in continuous mode for an exposure time of 10 min drastically reduced the viability of C. parvum. Thus, oocyst viabilities of 4.16 ± 1.93%; 1.29 ± 0.86%; 3.16 ± 0.69%; and 3.15 ± 0.87% were obtained in distilled water, simulated, real and filtered MWTP effluents, respectively (vs 98.57 ± 0.01%, initial oocyst viability), as determined using inclusion/exclusion of the fluorogenic vital dye propidium iodide, an indicator of the integrity of the oocyst wall. Independently of the mode used (pulsed/continuous) and at 80 W power, higher level of oocyst inactivation was detected in MWTP effluents than in distilled water used as a control solution, may be due to the differences in the chemical composition of the samples. Comparison of the results obtained in both modes showed that use of the continuous mode yielded significantly lower oocyst viability. However, when the Dose parameter was considered (energy per volume unit), no statistically significant differences in oocyst viability were observed in relation to the type of mode used. The results demonstrate that ultrasound technology represents a promising alternative to the disinfection methods (ultraviolet irradiation and chlorine products) currently used in water reclamation as it drastically reduces the survival of Cryptosporidium oocysts, without changing the chemical composition of the water or producing toxic by-products.

Ultrasound enhanced electrochemical oxidation of Alizarin Red S on boron doped diamond(BDD) anode:Effect of degradation process parameters

Textile wastewater is characterized by high toxicity, complex structure, and resistance to biodegradation. Therefore, advanced oxidation technologies have received extensive attention. However, it is usually difficult to achieve a desired degradation effect using a single technology. The combination of various advanced oxidation technologies is an important way to achieve efficient degradation of organic wastewater. The present investigation was focused on ultrasound enhanced electrochemical oxidation (US-EO) of typical anthracene Alizarin Red S dye on a boron doped diamond anode. Our work indicates that ultrasonic oxidation technology which is mainly based on cavitation, can produce strongly oxidizing active substances such as OH, HO₂, O, and H₂O₂, that accelerate the destruction of the dye molecular structure and achieve dye decolorization and mineralization. The effects on cavitation and decomposition of ARS by the parameters that affect degradation, including solution temperature, initial pH, and electrolytes, were examined. Results show that low temperature was more conducive to ultrasonic cavitation in the US-EO process; the degradation efficiency rate of EO was higher than that of US-EO when the solution temperature was above 45 °C. Ultrasonic cavitation was significantly more efficient in acid than in alkaline conditions. Almost 100% color removal and 86.07% COD removal was achieved for 100 mg L^-1 ARS concentration with a 0.05 M Na₂SO₄ electrolyte, temperature of 30 °C and pH of 4.97 after 3 h. GC-MS analysis showed that the intermediate products of ARS in the US-EO process were phthalic anhydride, PEAs and bisphenol A, which is eventually mineralized to CO₂ and H₂O.

Facile approach for synthesis of stable, efficient, and recyclable ZnO through pulsed sonication and its application for degradation of recalcitrant azo dyes in wastewater

In the present study, the ultrasound in pulsed mode was used as a part of an advanced oxidation method. The influence of the pulsed ultrasound mode for the preparation of the zinc oxide (ZnO) wurtzite nanoparticle was investigated. The catalysts synthesized were analysed using SEM, TEM, EDAX, BET surface area, XRD, and DRS to study their morphological and structural characterizations. The ZnO nanoparticles exhibited a highly hexagonal structure from pulsed sonication synthesis route. The efficiency of the decolourization of the reactive red 4 (RR4) dye was studied under different operation parameters such as dye concentration, initial solution pH, oxidant (e.g., H2O2) concentration, and catalyst loading. The hybrid combined process of pulsed sonolysis, pH (4.0), H2O2 (17.64 mmol), and catalyst (0.35 g/L) achieved 97% degradation and 87.5% chemical oxygen demand removal in about 20 min of reaction time. The cyclic degradation studies of RR4 removal with 0.35 g/L of ZnO showed the reusability of catalyst up to the fifth removal cycle with negligible loss in the catalytic performance. GC–MS study, used for the detection of the RR4 intermediates, revealed the oxidation–reduction reaction by the reactive radicals proceeded via the reductive cleavage of the azo bonds. The studied process, based on the pulsed ultrasound, is found to be effective for the degradation of RR4 dye.

Effects of Ultrasound Pretreatment on Eucalyptus Thermal Decomposition Characteristics As Determined by Thermogravimetric, Differential Scanning Calorimetry, and Fourier Transform Infrared Analysis

Samples were pretreated by ultrasound at 300 W and 28 kHz in three different solutions. The thermal degradation characteristics of the samples were then characterized via thermogravimetric, differential scanning calorimetry, and Fourier transform infrared analysis in a nitrogen environment. The characteristic of gas product release, the formation mechanisms of the main products, and the mechanistic basis for the effects of ultrasound on wood components were studied. The results showed that the gaseous products are the same with ultrasound pretreatment but the amounts are changed. The gaseous products mainly constitute of CO, H₂O, CO₂, CH₄, and CH₃COOH, and more gaseous products were produced at 361 °C than at 308 °C. The reaction rates for specimens pretreated in aqueous soda solution proceeded faster than specimens pretreated in aqueous acetic acid solution and distilled water. Moreover, the maximum FTIR spectra absorbance appeared around 341 °C for specimens pretreated in aqueous soda solution but appeared around 369 °C for the control sample and samples pretreated in distilled water or acetic acid solution. The heat flows for specimens pretreated in aqueous soda solution, compared to control group, was much lower. Additionally, hydroxyl and hydroperoxy radicals provided by ultrasound cavitation in alkaline conditions act to intensify the overall rates of reactions.

Sonocatalytic activity of a heterostructured β-Bi2O3/Bi2O2CO3 nanoplate in degradation of bisphenol A

Novel heterostructured β-Bi₂O₃/Bi₂O₂CO₃ nanoplates (hBN) were synthesized to observe the sonocatalytic degradation of bisphenol A (BPA) (widely used as a model pollutant) under ultrasonic (US) irradiation. Prior to obtaining the hBN, the Bi₂O₂CO₃ micropowder precursor was prepared under hydrothermal conditions and then converted to hBN by increasing the calcination temperature to 300 °C. The synthesized hBN samples were characterized by field emission scanning electron microscope with energy dispersive X-ray analysis (FESEM/EDX), transmission electron microscopy (TEM), X-ray diffraction (XRD), ultraviolet-visible spectrophotometer diffuse reflection spectroscopy (UV-vis DRS), and X-ray photoelectron spectroscopy (XPS). The hBN/US system exhibited greater sonocatalytic activity for the degradation of BPA than the US treatment with the single element bismuth oxide, β-Bi₂O₃ prepared by annealing the Bi₂O₂CO₃ precursor at 400 °C for 1 h. The US frequency and US power intensity in the hBN/US system were the key operating parameters, which were responsible for the complete degradation of BPA during 6 h of reactions. The degradation efficiency of BPA under the US irradiation was positively correlated with the dose of hBN. Our findings indicate that heterostructured hBN can be used as an efficient sonocatalyst for the catalytic degradation of BPA in water and wastewater treatment.

Performance of an indigenous integrated slurry photocatalytic membrane reactor (PMR) on the removal of aqueous phenanthrene (PHE)

In this study, a slurry photocatalytic membrane reactor (PMR) was developed and evaluated for the degradation of aqueous phenanthrene (PHE). During continuous process with a hydraulic retention time (HRT) of 140 min, the maximum PHE degradation and total organic carbon (TOC) removal efficiencies were found to be 97% and 79%, respectively. The reuse and recovery potential of TiO₂ was studied with continuous recycling. The major intermediates during photodegradation of PHE were found to be phenanthrenequinone, phenanthenol and fluorine. This study also includes an investigation of membrane fouling caused by hydrophilic nano TiO₂. The cake layer observed on the membrane surface was characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) and energy dispersive spectroscopy (EDS). In addition, the effect of operating parameters such as pH and permeate flux on membrane fouling were also investigated. Low permeate flux and alkaline conditions reduced membrane fouling.

Degradation of dye Procion Red MX-5B by electrolytic and electro-irradiated technologies using diamond electrodes

This work focuses on the treatment of synthetic wastewater polluted with dye Procion Red MX-5B by different Electrochemical Advanced Oxidation Processes (EAOP) based on diamond anodes. The influence of the current density and the supporting electrolyte has been studied on dye removal and total mineralization of the organic matter. Results show that electrolysis with diamond electrodes is a suitable technology for an efficient degradation of dye. Nonetheless, the process efficiency increases when using chloride as supporting electrolyte because of the electrochemical generation of hypochlorite in wastewater which significantly contribute to dye removal. On the contrary, the total mineralization of the organic matter is more efficient in sulfate media. In this case, large amounts of peroxodisulfate are electrogenerated, favoring the complete removal of total organic carbon (TOC). On the other hand, lower current densities (10 mA cm^-2) lead to a more efficient removal of both dye and TOC due to the mass transfer limitations of the technology. Finally, the coupling of UV light irradiation or ultrasound to electrolysis significantly improves the process performance, being photoelectrolysis the most efficient technology for the treatment of wastewater polluted with Procion Red MX-5B. This fact is due to the potential production of free chlorine or sulfate radicals that takes place by the activation of the electrogenerated oxidants. These species are more reactive than oxidants and, therefore, they quickly attack the organic matter present in wastewater.

Degradation of the UV-filter benzophenone-3 in aqueous solution using persulfate activated by heat, metal ions and light

The goals of this study were to bring forward new data and insights into the effect of activation methods, operational variables and reaction pathways during sulfate radicals-based oxidation of benzophenone-3 (BP-3) in aqueous solution. Heat, transition metal ions (Fe²⁺, Cu²⁺, Co²⁺), UV and visible light irradiation were used to activate persulfate (PS) to degrade BP-3. The results showed that these three activation methods can remarkably enhance BP-3 removal efficiency. Under the conditions of [BP-3]₀: [PS]₀ = 1: 500, pH = 7.0, and 40 °C, complete removal of BP-3 (1.31 μM) was observed in 3 h. In the pH range of 3.0-9.0, the degradation of BP-3 decreased with increasing pH. Increasing the PS dosage accelerated the reaction, while the presence of humic acid (HA) significantly inhibited the efficiency of BP-3 removal. Based on electron paramagnetic resonance (EPR) and radical quenching studies, sulfate and hydroxyl radicals contributed to the oxidation process. According to the evolution of BP-3 and its 7 by-products, as well as frontier electron densities (FED) calculation, two routes were proposed involving hydroxylation, demethylation and direct oxidation. On the whole, this work is a unique contribution to the systematic elucidation of BP-3 removal by PS.

Efficiency of biogas slurry and Burkholderia phytofirmans PsJN to improve growth, physiology, and antioxidant activity of Brassica napus L. in chromium-contaminated soil

Contamination of soil is a major problem globally with colligated danger for ecosystem and human health. Chromium (Cr) is a toxic heavy metal and caused harmful effect on growth and development of plants. Phytostabilization reduced the mobility of heavy metals with addition of amendments which can significantly decrease metal solubility in soil. Phytostabilization can be achieved by application of biogas slurry (BGS) and endophytic bacteria as amendments in the contaminated soils. The present study revealed that the Burkholderia phytofirmans PsJN and BGS improved the growth, physiology, and antioxidant activity and reduced Cr uptake under a pot experiment spiked with Cr (20 mg kg^-1 soil). The experiment was designed under completely randomized design, four treatments with three replications in normal and Cr-contaminated soil. The inoculation of endophytic bacteria improved the growth and physiology of Brassica. This study showed that the inoculation of endophytic bacteria stabilized the Cr levels in soil and minimized the uptake by the plant shoots and roots in BGS-amended soil. Similarly, activity of antioxidants such as catalase (CAT), reduced glutathione (GSH), glutathione peroxidase (GSH-Px), and glutathione s-transferase (GST) was decreased to normal with combined treatment of BGS and endophytic bacteria in Cr-stressed soil. Overall, the best results were analyzed by combined treatment of BGS and endophytic bacteria to improve growth, physiology, and antioxidant activity of Brassica and immobilize Cr in soil. Moreover, results emphasized the need to use BGS alone or in combination with endophytic bacteria to optimize crop performance, stabilize Cr concentration, and improve environmental efficiency.

Simultaneous removal of NO and SO2 from flue gas by combined heat and Fe2+ activated aqueous persulfate solutions

The use of advanced oxidation processes (AOPs) to integrate flue gas treatments for SO₂, NO_x and Hg⁰ into a single process unit is rapidly gaining research attention. AOPs are processes that rely on the generation of mainly the hydroxyl radical. This work evaluates the effectiveness of the simultaneous removal of NO and SO₂ from flue gas utilizing AOP induced by the combined heat and Fe²⁺ activation of aqueous persulfate, and elucidates the reaction pathways. The results indicated that both SO₂ in the flue gas and Fe²⁺ in solution improved NO removal, while the SO₂ is almost completely removed. Increased temperature led to increase in NO removal in the absence and presence of both Fe²⁺ and SO₂, and in the absence of either SO₂ or Fe²⁺, but the enhanced NO removal due to the presence of SO₂ alone dominated at all temperatures. The removal of NO increased from 77.5% at 30 °C to 80.5% and 82.3% at 50 °C and 70 °C in the presence of SO₂ alone, and from 35.3% to 62.7% and 81.2%, respectively, in the presence of Fe²⁺ alone. However, in the presence of both SO₂ and Fe²⁺, NO conversion is 46.2% at 30 °C, increased only slightly to 48.2% at 50 °C; but sharply increased to 78.7% at 70 °C compared to 63.9% for persulfate-only activation. Results suggest NO removal in the presence of SO₂ is equally effective by heat-only or heat-Fe²⁺ activation as the temperature increases. The results should be useful for future developments of advanced oxidation processes for flue gas treatments.

Simultaneous absorption of SO2 and NO from flue gas using ultrasound/Fe2+/heat coactivated persulfate system

A novel process on simultaneous absorption of SO₂ and NO from flue gas using ultrasound (US)/Fe²⁺/heat coactivated persulfate system was proposed. The influencing factors, active species, products and mechanism of SO₂ and NO removal were investigated. The results indicate that US enhances NO removal due to enhancement of mass transfer and chemical reaction. US of 28kHz is more effective than that of 40kHz. NO removal efficiency increases with increasing persulfate concentration, ultrasonic power density and Fe²⁺ concentration (at high persulfate concentration). Solution pH, solution temperature and Fe²⁺ concentration (at low persulfate concentration) have double effect on NO removal. SO₂ is completely removed in most of tested removal systems, except for using water absorption. US, Fe²⁺ and heat have a synergistic effect for activating persulfate to produce free radicals, and US/Fe²⁺/heat coactivated persulfate system achieves the highest NO removal efficiency. ·OH and SO₄^-· play a leading role for NO oxidation, and persulfate only plays a complementary role for NO oxidation.

Effects of ultrasonic and hydrodynamic cavitation on the treatment of cork wastewater by flocculation and Fenton processes

This paper reports that ultrasonic (US) and hydrodynamic cavitation (HC) are efficient strategies for the environmental remediation of cork wastewater (CW). It is necessary to remove toxic, inhibitory or refractory organic matter from CW using physical and chemical techniques (pre-treatment) prior to performing conventional biological treatment. After this biological treatment, it is also critical to further decontaminate (post-treatment) in order to meet the discharge limitation. The pre-treatment of diluted CW using Fenton oxidation (FE) alone led to COD and polyphenol (PP) removal values of 30% and 61%, respectively, while HC and US resulted in 83-90% increases in COD reduction and 26-33% increases in PP reduction. Whereas 55% and 91% COD and PP removal were achieved using flocculation (Floc) alone, COD elimination was increased by a further 7-18% under HC and US. No noticeable improvement in PP elimination was observed. US did not enhance the Floc decontamination of the original concentrated CW, however, considerable quantities of white biofilm were surprisingly generated on the CW surface after the pre-treatment, thus indicating the improvement of biodegradability of the resulting liquid. In fact, the post-treatment stage, using FE alone after having filtered the biofilms, led to reductions of 53% in COD and 90% in PP. The HC and US protocols resulted in 26-34% increases in COD elimination. HC further enhanced PP elimination caused by FE, while US resulted in lower levels of PP elimination.

Purification of Hg0 from flue gas by wet oxidation method and its mechanism: a review

The vast majority of Hg²⁺ can be removed while elemental mercury (Hg⁰) can hardly be removed due to its characteristic of high volatility and insolubility in water. Till now, how to oxidize Hg⁰ to Hg²⁺ is the key for the purification of Hg⁰, especially when there are others pollutants, such as HCl, SO₂, and NOx. In this review, the method and mechanism of Hg⁰ purification from flue gas by H₂O₂, KMnO₄, NaClO₂, and O₃ are reviewed comprehensively. It is concluded that the oxidation of Hg⁰ mainly depends on the electronic supply efficiency from the solution. The Fenton reagent, composed of H₂O₂ and metal cations, is superior to O₃ and the solution of KMnO₄ and NaClO₂. Moreover, HCl, SO₂, and NOx in the flue gas can influence the oxidation and purification mechanism of Hg⁰. It is found that HCl in flue gas had obvious auxo-action on the oxidation of mercury, and SO₂ and NOx have different effects on the oxidation of Hg⁰ with the change of compositions and concentration of pollutants in the flue gas. In general, SO₂ and NOx can slightly promote the oxidation of Hg⁰ due to the synergistic effect.