Photooxidation products of polycyclic aromatic compounds containing sulfur

A Light Touch: Solar Photocatalysis Detoxifies Oil Sands Process-Affected Waters Prior to Significant Treatment of Naphthenic Acids

Environmental reclamation of Canada's oil sands tailings ponds is among the single largest water treatment challenges globally. The toxicity of oil sands process-affected water (OSPW) has been associated with its dissolved organics, a complex mixture of naphthenic acid fraction components (NAFCs). Here, we evaluated solar treatment with buoyant photocatalysts (BPCs) as a passive advanced oxidation process (P-AOP) for OSPW remediation. Photocatalysis fully degraded naphthenic acids (NAs) and acid extractable organics (AEO) in 3 different OSPW samples. However, classical NAs and AEO, traditionally considered among the principal toxicants in OSPW, were not correlated with OSPW toxicity herein. Instead, nontarget petroleomic analysis revealed that low-polarity organosulfur compounds, composing <10% of the total AEO, apparently accounted for the majority of waters' toxicity to fish, as described by a model of tissue partitioning. These findings have implications for OSPW release, for which a less extensive but more selective treatment may be required than previously expected.

Photochemistry of oil in marine systems: developments since the Deepwater Horizon spill

Oil spills represent a major source of negative environmental impacts in marine systems. Despite many decades of research on oil spill behavior, photochemistry was neglected as a major factor in the fate of oil spilled in marine systems. Subsequent to the Deepwater Horizon oil spill, numerous studies using varied approaches have demonstrated the importance of photochemistry, including short-term impacts (hours to days) that were previously unrecognized. These studies have demonstrated the importance of photochemistry in the overall oil transformation after a spill and more specifically the impacts on emulsification, oxygenation, and microbial interactions. In addition to new perspectives, advances in analytical approaches have allowed an improved understanding of oil photochemistry after maritime spill. Although the literature on the Deepwater Horizon spill is extensive, this review focuses only on studies relevant to the advances in oil photochemistry understanding since the Deepwater Horizon spill.

Upwelling impact and lateral transport of dissolved PAHs in the Taiwan Strait and adjacent South China Sea

The spatial distribution and depth profile of dissolved polycyclic aromatic hydrocarbons (PAHs) were investigated in the western Taiwan Strait (TWS) and northeastern South China Sea (SCS) during the southwest monsoon for a comprehensive study of spatial distribution, potential sources, upwelling, and lateral PAHs transport flux to assess the impacts of oceanic processes. The concentrations of ∑14PAHs were 33 ± 14 ng L-1 and 23 ± 11 ng L-1 in western TWS and northeastern SCS, respectively. A minor difference in potential sources in different areas was shown in principle component analysis results, which illustrated mixed sources (petrogenic and pyrogenic) in western TWS and petrogenic sources in northeastern SCS. An "enrichment in surface or deep but depletion in medium water" distribution pattern of PAHs depth profile during summertime was observed in Taiwan Bank, which was potentially influenced by the upwelling. The greatest lateral ∑14PAHs transport flux was found along the Taiwan Strait Current area (43.51 g s-1), followed by those along South China Sea Warm Current and Guangdong Coastal Current areas. Though the oceanic response to PAHs varied relatively slowly, the ocean current was a less-dominant pathway for PAHs exchange between the SCS and the East China Sea (ECS).

Deciphering structure and aggregation in asphaltenes: hypothesis-driven design and development of synthetic model compounds

Asphaltenes comprise the heaviest and least understood fraction of crude petroleum. The asphaltenes are a diverse and complex mixture of organic and organometallic molecules in which most of the molecular constituents are tightly aggregated into more complicated suprastructures. The bulk properties of asphaltenes arise from a broad range of polycyclic aromatics, heteroatoms, and polar functional groups. Despite much analytical effort, the precise molecular architectures of the material remain unresolved. To understand asphaltene characteristics and reactivity, the field has turned to synthetic model compounds that mirror asphaltene structure, aggregation behavior, and thermal chemistry, including the nucleation of coke. Historically, molecular asphaltene modeling was limited to commercial compounds, offering little illumination and few opportunities for hypothesis-driven research. More recently, however, rational molecular design and modern organic synthesis have started to impact this area. This review provides an overview of commercially available model compounds but is principally focused on the design and synthesis of structurally advanced and appropriately functionalized compounds to mimic the physical and chemical behavior of asphaltenes. Efforts to model asphaltene aggregation are briefly discussed, and a prognosis for the field is offered. A referenced tabulation of the synthetic compounds reported to date is provided.

Photooxidation and biodegradation potential of a light crude oil in first-year sea ice

Disappearing sea ice in the Arctic region results in a pressing need to develop oil spill mitigation techniques suitable for ice-covered waters. The uncertainty around the nature of an oil spill in the Arctic arises from the ice-covered waters and sub-zero temperatures, and how they may influence natural attenuation efficiency. The Sea-ice Environmental Research Facility was used to create a simulated Arctic marine setting. This paper focuses on the potential for biodegradation of the bulk crude oil content (encapsulated in the upper regions of the ice), to provide insight regarding the possible fate of crude oil in an Arctic marine setting. Cheaper and faster methods of chemical composition analysis were applied to the samples to assess for weathering and transformation effects. Results suggest that brine volume in ice may not be sufficient at low temperatures to encompass biodegradation and that seawater is more suitable for biodegradation.

Effect of dissolution, evaporation, and photooxidation on crude oil chemical composition, dielectric properties and its radar signature in the Arctic environment

Accidental release of petroleum in the Arctic is of growing concern owing to increases in ship traffic and possible future oil exploration. A crude oil-in-sea ice mesocosm experiment was conducted to identify oil-partitioning trends in sea ice and determine the effect of weathering on crude oil permittivity. The dissolution of the lighter fractions increased with decreasing bulk oil-concentration because of greater oil-brine interface area. Movement of the oil towards the ice surface predominated over dissolution process when oil concentrations exceeded 1 mg/mL. Evaporation decreased oil permittivity due to losses of low molecular weight alkanes and increased asphaltene-resin interactions. Photooxidation increased the permittivity of the crude oil due to the transformation of branched aromatics to esters and ketones. Overall, the weathering processes influenced crude oil permittivity by up to 15%, which may produce sufficient quantifiable differences in the measured normalized radar cross-section of the ice.

Comparison of UV/Persulfate and UV/H2O2 for the removal of naphthenic acids and acute toxicity towards Vibrio fischeri from petroleum production process water

The ultraviolet light-activated persulfate process (UV/Persulfate) has received much attention in recent years as a novel advanced oxidation method for the treatment of municipal and industrial wastewater. This work investigated the UV/Persulfate and UV/H₂O₂ processes for the treatment of real oil sands process water (OSPW) at ambient pH condition using a medium pressure mercury lamp (emission between 200 and 530 nm). The degradation performances towards fluorophore organic compounds and naphthenic acids (NAs) in OSPW were evaluated using synchronous fluorescence spectrometry and ultra performance liquid chromatography time-of-flight mass spectrometry, respectively. Compared to the UV/H₂O₂ process, the UV/Persulfate process exhibited higher efficiency to remove both NAs and fluorophore organic compounds. Under 40 min of UV exposure and incident irradiance of 3.50 mW cm^-2, fluorophore organic compounds were greatly degraded by UV/Persulfate (2 mM) and two- and three-ring fused organics were completely removed. 59.4%, 83.8% and 92.2% of O₂-NAs in OSPW were removed with persulfate dosages of 0.5, 2, and 4 mM, respectively. The removal efficiency decreased along with the number of oxygen atoms in NAs (83.8%, 49.3%, and 46.8% for O₂-, O₃-, and O₄-NAs, respectively) with 2 mM of persulfate, because of the formation of oxidized NAs in the same process. The structure-reactivity of O₂-NA compounds fitted pseudo-first order kinetics in UV/Persulfate process with the rate constants ranging from 0.0156 min^-1 to 0.1511 min^-1. NAs with higher carbon numbers and double bond equivalence were more reactive in the UV/Persulfate oxidation process. The acute toxicity of OSPW to Vibrio fischeri was significantly reduced after the UV/Persulfate and UV/H₂O₂ treatments. Overall results demonstrated that the UV/Persulfate oxidation can be an effective alternative for future reclamation of OSPW.

A tiered analytical approach for target, non-target and suspect screening analysis of polar transformation products of polycyclic aromatic compounds

Polycyclic aromatic compounds (PACs) possess toxicity towards humans, and their presence in the environment is unwanted. Polar transformation products (TPs) are more mobile, and can be considered emerging contaminants, as they represent a more bioavailable carrier of the same toxic properties. Acidic TPs has been proposed as an important class of polar TPs. This study presents a tiered analytical approach to investigate acidic and polar PAC TPs in environmental conditions. The tiered approach exploits target analysis for quantification of acids; suspect screening for tentative identification based on retention time and spectral matching using databases; and finally non-target analysis based on chromatography and data independent broadband MS to highlight potentially unknown analyte peaks. The approach includes a mixed-mode anion exchange solid phase extraction (MAX-SPE) to fractionate neutral and acidic compounds, and is applied to three cases: I) Photo-oxidation of six PACs generated suspected hydroxylated-, carbonylated- and carboxylated PACs but also proposed the presence of mono- and dicarboxylic acids, which have not been reported elsewhere. For a subset of four acids, conversion rates were determined. II) Recovery of spiked acids from diesel spilled harbor water was 80% by LC-MS, and diesel spill weathering was evaluated from the neutral fraction by GC-MS. III) By non-target analysis sulfonated PACs, presumable derived from photo-oxidation, were detected in run-off basins of an arctic landfarm, alongside hypothesized naturally occuring fatty acids. The tiered approach is a sensitive and versatile tool to extract information on PACs and their polar TPs from polluted environmental sites.

Molecular-level investigation of soils contaminated by oil spilled during the Gulf War

In this study, molecular-level chemical compositions of soils contaminated by oil spilled during the Gulf War were studied. Two soil samples, respectively collected at 0.1 m and between 0.5 and 1 m below the surface from an oil spill site, were extracted with organic solvents and water. The extracts were analyzed via ultrahigh resolution FT-ICR and two-dimensional gas chromatography/high resolution mass spectrometry. The data showed that the spilled oil was significantly affected by vaporization due to high surface temperatures in the desert. The data obtained with (+) atmospheric pressure photo ionization (APPI) and (-) electrospray ionization (ESI) coupled with ultrahigh resolution-mass spectrometry (UHR-MS) indicated that the degradation of aromatic compounds and increase in oxygen-containing classes occurred in the following order: surface soil > below surface soil > crude oil. The oxygenated compounds were confirmed by principal component analysis. The score and loading plots of O_x and SO_x showed that they were the major contributors to differentiate the samples. However, a comparison with previously reported oceanic oil spills showed that less significant degradation occurred even after almost 30 years. Our data can provide an information basis for designing a strategy for clean-up and restoration efforts of Gulf War oil spills.

Molecular-Level Characterization of Oil-Soluble Ketone/Aldehyde Photo-Oxidation Products by Fourier Transform Ion Cyclotron Resonance Mass Spectrometry Reveals Similarity Between Microcosm and Field Samples

We present a solid-phase extraction method followed by derivatization with a charged tag to characterize ketone/aldehyde-containing functionalities (proposed photo-oxidation transformation products) in weathered petroleum by Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). A photo-oxidation-only microcosm mimics solar irradiation of crude oil in the environment after an oil spill. A biodegradation-only microcosm enables independent determination as to which of the two weathering processes contributes to the formation of oil-soluble ketone/aldehyde species. Results confirm that photo-oxidation produces ketones/aldehydes in crude oil when exposed to solar radiation in laboratory experiments, whereas biodegraded oil samples do not produce ketone/aldehyde compounds. Field samples collected after different time periods and locations after the Deepwater Horizon oil spill are also shown to contain ketones/aldehydes, and comparison of field and photo-oxidation-only microcosm transformation products reveal remarkable similarity. These results indicate that the photo-oxidation microcosm comprehensively represents ketone/aldehyde-formation products in the field, whereas the biodegradation microcosm does not. Solid-phase extraction coupled with derivatization leads to selective identification of ketone/aldehyde species by MS. Although improved dynamic range and slightly reduced mass spectral complexity is achieved by separation/derivatization, comprehensive molecular characterization still requires mass resolving power and mass accuracy provided by FT-ICR MS.

Petroleomic depth profiling of Staten Island salt marsh soil: 2ω detection FTICR MS offers a new solution for the analysis of environmental contaminants

Staten Island is located in one of the most densely populated regions of the US: the New York/New Jersey Estuary. Marine and industrial oil spills are commonplace in the area, causing the waterways and adjacent marshes to become polluted with a range of petroleum-related contaminants. Using Rock-Eval pyrolysis, the hydrocarbon impact on a salt marsh was assessed at regular intervals down to 90 cm, with several key sampling depths of interest identified for further analysis. Ultrahigh resolution data are obtained by direct infusion (DI) atmospheric pressure photoionization (APPI) on a 12 T solariX Fourier transform ion cyclotron resonance mass spectrometer (FTICR MS) allowing trends in the compositional profile with depth to be observed, such as changes in the relative hydrocarbon intensity and the relative contributions from oxygen- and sulfur-containing groups. These trends may correlate with the timing of major oil spills and leaks of petroleum and other industrial chemicals into the waterways. The use of gas chromatography (GC) coupled to a 7 T solariX 2XR FTICR MS equipped with an atmospheric pressure chemical ionization (APCI) ion source offers retention time resolved and extensive compositional information for the complex environmental samples complementary to that obtained by DI-APPI. The compositional profile observed using GC-APCI FTICR MS includes contributions from phosphorous-containing groups, which may be indicative of contamination from other anthropogenic sources.

Structure-reactivity relationship of naphthenic acids in the photocatalytic degradation process

Bitumen extraction in Canada's oil sands generates oil sands process-affected water (OSPW) as a toxic by-product. Naphthenic acids (NAs) contribute to the water's toxicity, and treatment methods may need to be implemented to enable safe discharge. Heterogeneous photocatalysis is a promising advanced oxidation process (AOP) for OSPW remediation, however, its successful implementation requires understanding of the complicated relationship between structure and reactivity of NAs. This work aimed to study the effect of various structural properties of model compounds on the photocatalytic degradation kinetics via high resolution mass spectrometry (HRMS), including diamondoid structures, heteroatomic species, and degree of unsaturation. The rate of photocatalytic treatment increased significantly with greater structural complexity, namely with carbon number, aromaticity and degree of cyclicity, properties that render particular NAs recalcitrant to biodegradation. It is hypothesized that a superoxide radical-mediated pathway explains these observations and offers additional benefits over traditional hydroxyl radical-based AOPs. Detailed structure-reactivity investigations of NAs in photocatalysis have not previously been undertaken, and the results described herein illustrate the potential benefit of combining photocatalysis and biodegradation as a complete OSPW remediation technology.

Fate of oxygenated intermediates in solar irradiated diluted bitumen mixed with saltwater

Two types of diluted bitumen (dilbit) and a light crude oil spiked onto the surface of saltwater were irradiated with natural solar light in Ottawa to assess the impact of sunlight to the fate of oxygenated intermediates. Oxygenated components, including carbonyl polycyclic aromatic hydrocarbons (PAHs) and acidic polar fractions (naphthenic acid fraction compounds, NAFCs), were identified after periods of solar exposure under both winter and summer conditions. Carbonyl PAHs and NAFCs were formed in both seasons; however, light crude and summer irradiation produced higher abundance of them than dilbits and winter exposure. The formed NAFCs were abundant with the congeners containing a heteroatom of oxygen only (O_o species), accompanied by the minor amounts of sulfur- and nitrogen-containing acids. The produced O_o species were predominant with the congeners with light molecular weight, high degree of saturation and heavy oxygen numbers. For both carbonyl PAHs and NAFCs, their abundance continually increased throughout the period of winter exposure. In the summer, some carbonyl PAHs and all O_o species increased during the early exposure period; then they decreased with continued exposure for most oils, illustrating their transitional nature. Oxygenated intermediates thus appear to have been created through the photo-oxidation of non-to medium-polar petroleum hydrocarbons or the intermediates of aldehydes or ketones (O₁). Oil properties, the duration of exposure, exposure season and the chemical structure of these intermediates are critical factors controlling their fate through photo-oxidation. The observed chemical changes highlight the effects of sunlight on the potential behavior, fate and impact of spilled oil, with the creation of new resin group compounds and the reduction of aromatics and saturates. These results also imply that the ecological effects of spilled oil, after ageing in sunlight, depend on the specific oil involved and the environmental conditions.

Assessing the hydroxyl radical and volatilization roles in aquatic fate estimations of sulfur heterocycles: Dibenzothiophene derivatives

Polycyclic aromatic sulfur heterocycles (PASHs) and their alkyl derivatives can be released into aquatic systems via crude oil spills or runoff from petroleum-treated areas, such as asphalt. Dibenzothiophene (DBT) and its derivatives (C1-DBT, C2-DBT, and C4-DBT) were chosen as model compounds to investigate the relative impact of volatilization and hydroxyl radical degradation on estimates of their overall dissipation after entry into aquatic ecosystems as a function of depth using the exposure analysis modeling system (EXAMS). The hydroxyl radical rate constant (K _· OH ) and Henry's law constant of PASHs were determined in distilled water. The analogue C1-DBT reacted fastest with · OH relative to other PASHs. The C2-DBT and C4-DBT analogues had higher Henry's law constants compared with other derivatives. Steric hindrance by alkyl substituents on the sulfur moiety most strongly impacted measured rate and Henry's law constants between DBT and individual alkyl derivatives. These steric effects do not appear to be considered in the physical property estimation software EPI Suite. Simulated dissipation of PASHs using EXAMS suggests that volatilization is a dominant fate pathway for the higher molecular weight and less polar C2-DBT and C4-DBT at all depths and DBT and C1-DBT at 0.1-m. However, model scenarios suggest that hydroxyl radical degradation may significantly contribute to the degradation of more polar DBT and C1-DBT at 1-m and 2-m depths. Environ Toxicol Chem 2017;36:1998-2004. © 2017 SETAC.

Application of phase correction to improve the characterization of photooxidation products of lignin using 7 Tesla Fourier-transform ion cyclotron resonance mass spectrometry

Lignin is the second most abundant natural biopolymer and potentially a valuable alternative energy source for conventional fossil fuels. In this study, Fourier-transform ion cyclotron resonance-mass spectrometry (FTICR-MS) in conjunction with phase correction was applied to study photooxidation products of lignin using a 7 Tesla (T) mass spectrometer. The application of 7 T FTICR-MS has often been inadequate for the analysis of complex natural organic matter because of insufficient resolving power as compared with high-field FTICR, which led to incorrect assignments of elemental formulae and discontinuous plots in graphical and statistical analyses. Here, the application of phase correction to the FTICR mass spectra of lignin oxidation products greatly improved the spectral quality, and thus, readily permitted characterization of photooxidation processes of lignin compounds under simulated solar radiation conditions.

Comparison of Nitrilotriacetic Acid and [S,S]-Ethylenediamine-N,N'-disuccinic Acid in UV-Fenton for the Treatment of Oil Sands Process-Affected Water at Natural pH

The application of UV-Fenton processes with two chelating agents, nitrilotriacetic acid (NTA) and [S,S]-ethylenediamine-N,N'-disuccinic acid ([S,S]-EDDS), for the treatment of oil sands process-affected water (OSPW) at natural pH was investigated. The half-wave potentials of Fe(III/II)NTA and Fe(III/II)EDDS and the UV photolysis of the complexes in Milli-Q water and OSPW were compared. Under optimum conditions, UV-NTA-Fenton exhibited higher efficiency than UV-EDDS-Fenton in the removal of acid extractable organic fraction (66.8% for the former and 50.0% for the latter) and aromatics (93.5% for the former and 74.2% for the latter). Naphthenic acids (NAs) removals in the UV-NTA-Fenton process (98.4%, 86.0%, and 81.0% for classical NAs, NAs + O (oxidized NAs with one additional oxygen atom), and NAs + 2O (oxidized NAs with two additional oxygen atoms), respectively) under the experimental conditions were much higher than those in the UV-H₂O₂ (88.9%, 48.7%, and 54.6%, correspondingly) and NTA-Fenton (69.6%, 35.3%, and 44.2%, correspondingly) processes. Both UV-NTA-Fenton and UV-EDDS-Fenton processes presented promoting effect on the acute toxicity of OSPW toward Vibrio fischeri. No significant change of the NTA toxicity occurred during the photolysis of Fe(III)NTA; however, the acute toxicity of EDDS increased as the photolysis of Fe(III)EDDS proceeded. NTA is a much better agent than EDDS for the application of UV-Fenton process in the treatment of OSPW.

Shedding light on the structures of lignin compounds: photo-oxidation under artificial UV light and characterization by high resolution mass spectrometry

Lignin is the second most abundant natural polymer and a promising alternative energy source for conventional fossil fuels. In this study, we investigated transformations of lignin compounds under artificial UV light conditions at the molecular level. Such light-induced changes of composition profiles in nature after sun exposure have been studied for crude oil in the petroleomics field. We applied a similar high resolution mass spectrometry experimental strategy to lignin and demonstrated various data processing methods to reveal the characteristic differences between the extremely complex data sets of two sample sets, one native control before and one sample after photo-irradiation, using Fourier transform ion cyclotron resonance-mass spectrometry. Graphical abstract Kendrick mass defect versus nominal Kendrick mass for mass spectra of a control and UV-oxidized lignin sample.

Solar photocatalytic degradation of naphthenic acids in oil sands process-affected water

Bitumen mining in the Canadian oil sands creates large volumes of oil sands process-affected water (OSPW), the toxicity of which is due in part to naphthenic acids (NAs) and other acid extractable organics (AEO). The objective of this work was to evaluate the potential of solar photocatalysis over TiO2 to remove AEO from OSPW. One day of photocatalytic treatment under natural sunlight (25 MJ/m(2) over ∼14 h daylight) eradicated AEO from raw OSPW, and acute toxicity of the OSPW toward Vibrio fischeri was eliminated. Nearly complete mineralization of organic carbon was achieved within 1-7 day equivalents of sunlight exposure, and degradation was shown to proceed through a superoxide-mediated oxidation pathway. High resolution mass spectrometry (HRMS) analysis of oxidized intermediate compounds indicated preferential degradation of the heavier and more cyclic NAs (higher number of double bond equivalents), which are the most environmentally persistent fractions. The photocatalyst was shown to be recyclable for multiple uses, and thus solar photocatalysis may be a promising "green" advanced oxidation process (AOP) for OSPW treatment.

Natural Sunlight Shapes Crude Oil-Degrading Bacterial Communities in Northern Gulf of Mexico Surface Waters

Following the Deepwater Horizon (DWH) spill in 2010, an enormous amount of oil was observed in the deep and surface waters of the northern Gulf of Mexico. Surface waters are characterized by intense sunlight and high temperature during summer. While the oil-degrading bacterial communities in the deep-sea plume have been widely investigated, the effect of natural sunlight on those in oil polluted surface waters remains unexplored to date. In this study, we incubated surface water from the DWH site with amendments of crude oil, Corexit dispersant, or both for 36 days under natural sunlight in the northern Gulf of Mexico. The bacterial community was analyzed over time for total abundance, density of alkane and polycyclic aromatic hydrocarbon degraders, and community composition via pyrosequencing. Our results showed that, for treatments with oil and/or Corexit, sunlight significantly reduced bacterial diversity and evenness and was a key driver of shifts in bacterial community structure. In samples containing oil or dispersant, sunlight greatly reduced abundance of the Cyanobacterium Synechococcus but increased the relative abundances of Alteromonas, Marinobacter, Labrenzia, Sandarakinotalea, Bartonella, and Halomonas. Dark samples with oil were represented by members of Thalassobius, Winogradskyella, Alcanivorax, Formosa, Pseudomonas, Eubacterium, Erythrobacter, Natronocella, and Coxiella. Both oil and Corexit inhibited the Candidatus Pelagibacter with or without sunlight exposure. For the first time, we demonstrated the effects of light in structuring microbial communities in water with oil and/or Corexit. Overall, our findings improve understanding of oil pollution in surface water, and provide unequivocal evidence that sunlight is a key factor in determining bacterial community composition and dynamics in oil polluted marine waters.

Structure-dependent degradation of polar compounds in weathered oils observed by atmospheric pressure photo-ionization hydrogen/deuterium exchange ultrahigh resolution mass spectrometry

The resin fractions of fresh mixtures of three oils spilled during the M/V Hebei Spirit oil spill, as well as weathered oils collected at weathering stages II and IV from the oil spill site were analyzed and compared by atmospheric pressure photo-ionization hydrogen/deuterium exchange mass spectrometry (HDX MS). The significantly decreased abundance of N(+) and [N-H+D](+) ions suggested that secondary and tertiary amine-containing compounds were preferentially degraded during the early stage of weathering. [N+H](+) and [N+D](+) ions previously attributed to pyridine-type compounds degraded more slowly than secondary and tertiary amine-containing compounds. The preferential degradation of nitrogen-containing compounds was confirmed by photo-degradation experiments using 15 standard compounds. In addition, significant increases of [S1O1+H](+) and [S1O1+D](+) ions with higher DBE values were observed from fresh oil mixtures as compared to stages II and IV samples, and that could be linked with the decrease of higher DBE compounds of the S1 class. This study presented convincing arguments and evidence demonstrating that secondary and tertiary amines were more vulnerable to photo-degradation than compounds containing pyridine, and hence, preferential degradation depending on chemical structures must be considered in the production of hazardous or toxic components.

Differentiating the roles of photooxidation and biodegradation in the weathering of Light Louisiana Sweet crude oil in surface water from the Deepwater Horizon site

We determined the contributions of photooxidation and biodegradation to the weathering of Light Louisiana Sweet crude oil by incubating surface water from the Deepwater Horizon site under natural sunlight and temperature conditions. N-alkane biodegradation rate constants were ca. ten-fold higher than the photooxidation rate constants. For the 2-3 ring and 4-5 ring polycyclic aromatic hydrocarbons (PAHs), photooxidation rate constants were 0.08-0.98day(-1) and 0.01-0.07day(-1), respectively. The dispersant Corexit enhanced degradation of n-alkanes but not of PAHs. Compared to biodegradation, photooxidation increased transformation of 4-5 ring PAHs by 70% and 3-4 ring alkylated PAHs by 36%. For the first time we observed that sunlight inhibited biodegradation of pristane and phytane, possibly due to inhibition of the bacteria that can degrade branched-alkanes. This study provides quantitative measures of oil degradation under relevant field conditions crucial for understanding and modeling the fate of spilled oil in the northern Gulf of Mexico.

Time to Say Goodbye to the 16 EPA PAHs? Toward an Up-to-Date Use of PACs for Environmental Purposes

The 16 EPA PAHs have played an exceptionally large role above all in environmental and analytical sciences in the last 40 years, but now there are good reasons to question their utility in many circumstances even though their use is so established and comfortable. Here we review the reasons why the list has been so successful and why sometimes it is seen as less relevant. Three groups of polycyclic aromatic compounds (PAC) are missing: larger and highly relevant PAHs, alkylated PACs, and compounds containing heteroatoms. Attempts to improve the situation for certain matrixes are known and here: (1) an updated list of PAHs (including the 16 EPA PAHs) for the evaluation of the toxicity in the environment (40 EnvPAHs); (2) a list of 23 NSO-heterocyclic compounds and 6 heterocyclic metabolites; and (3) lists of 10 oxy-PAHs and 10 nitro-PAHs are proposed for practical use in the future. A discussion in the scientific community about these lists is invited. Although the state of knowledge has improved dramatically since the introduction of the 16 EPA PAHs in the 1970s, this summary also shows that more research is needed about the toxicity, occurrence in the environment and chemical analysis, particularly of alkylated PAHs, higher molecular weight PAHs and substituted PACs such as amino-PAHs, cyano-PAHs, etc.. We also suggest that a long overdue discussion of an update of regulatory environmental PAH analysis is initiated.

A practical review on photooxidation of crude oil: laboratory lamp setup and factors affecting it

After an oil spill, crude oil in the marine environment is affected by a variety of processes collectively called weathering. Photooxidation induced by ultraviolet (UV) light from the sun is one of the most significant processes of long-term weathering that changes the chemical nature of oil. Experimental studies on photooxidation in the natural environment are generally not practicable due to the variability of factors that are more readily controlled in a laboratory. The emission spectra and irradiance of artificial lamps are critical factors for simulating sunlight, and the process of acceleration should be differentiated from simulation. We present a comprehensive review of the exposure conditions affecting in vitro photooxidation studies, including the types of lamps, their spectra and irradiance levels and maintenance conditions. The importance of xenon arc, metal halide along with mercury–xenon, high-pressure mercury lamps and other lamps with respect to their spectral characteristics is discussed and the selection guide is provided. A brief discussion on other factors affecting photooxidation rates and outcomes, such as photosensitisers, photodegraders, solvents and the synergistic effects of compounds is also given.

Sunlight creates oxygenated species in water-soluble fractions of Deepwater Horizon oil

In order to assess the impact of sunlight on oil fate, Macondo well oil from the Deepwater Horizon (DWH) rig was mixed with pure water and irradiated with simulated sunlight. After irradiation, the water-soluble organics (WSO) from the dark and irradiated samples were extracted and characterized by ultrahigh resolution Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS). Liquid-liquid extraction yielded two fractions from dark and irradiated water/oil mixtures: acidic WSOs (negative-ion electrospray (ESI)), and base/neutral WSOs (positive-ion ESI) coupled to FT-ICR MS to catalog molecular-level transformations that occur to Macondo-derived WSOs after solar irradiation. Such direct measure of oil phototransformation has not been previously reported. The most abundant heteroatom class detected in the irradiated WSO acid fractions correspond to molecules that contain five oxygens (O5), while the most abundant acids in the dark samples contain two oxygen atoms per molecule (O2). Higher-order oxygen classes (O5-O9) were abundant in the irradiated samples, but <1.5% relative abundance in the dark sample. The increased abundance of higher-order oxygen classes in the irradiated samples relative to the dark samples indicates that photooxidized components of the Macondo crude oil become water-soluble after irradiation. The base/neutral fraction showed decreased abundance of pyridinic nitrogen (N1) concurrent with an increased abundance of N1Ox classes after irradiation. The predominance of higher-order oxygen classes indicates that multiple photochemical pathways exist that result in oxidation of petroleum compounds.

Weathering trend characterization of medium-molecular weight polycyclic aromatic disulfur heterocycles by Fourier transform ion cyclotron resonance mass spectrometry

Different weathering factors act to change petroleum composition once it is spilled into the environment. n-Alkanes, biomarkers, low-molecular weight polyaromatic hydrocarbons and sulfur heterocycles compositional changing in the environment have been extensively studied by different researchers and many parameters have been used for oil source identification and monitoring of weathering and biological degradation processes. In this work, we studied the fate of medium-molecular weight polycyclic aromatic disulfur heterocycles (PAS2Hs), up to ca. 900Da, of artificially weathered Flotta North Sea crude oil by ultra high-resolution Fourier transform ion cyclotron resonance mass spectrometry. It was found that PAS2Hs in studied crude oil having double bond equivalents (DBE) from 5 to 8 with a mass range from ca 316 to 582Da were less influenced even after six months artificial weathering experiment. However, compounds having DBEs 12, 11 and 10 were depleted after two, four and six months weathering, respectively. In addition, DBE 9 series was more susceptible to weathering than those of DBE 7 and 8.

Application of a solar UV/chlorine advanced oxidation process to oil sands process-affected water remediation

The solar UV/chlorine process has emerged as a novel advanced oxidation process for industrial and municipal wastewaters. Currently, its practical application to oil sands process-affected water (OSPW) remediation has been studied to treat fresh OSPW retained in large tailings ponds, which can cause significant adverse environmental impacts on ground and surface waters in Northern Alberta, Canada. Degradation of naphthenic acids (NAs) and fluorophore organic compounds in OSPW was investigated. In a laboratory-scale UV/chlorine treatment, the NAs degradation was clearly structure-dependent and hydroxyl radical-based. In terms of the NAs degradation rate, the raw OSPW (pH ∼ 8.3) rates were higher than those at an alkaline condition (pH = 10). Under actual sunlight, direct solar photolysis partially degraded fluorophore organic compounds, as indicated by the qualitative synchronous fluorescence spectra (SFS) of the OSPW, but did not impact NAs degradation. The solar/chlorine process effectively removed NAs (75-84% removal) and fluorophore organic compounds in OSPW in the presence of 200 or 300 mg L(-1) OCl(-). The acute toxicity of OSPW toward Vibrio fischeri was reduced after the solar/chlorine treatment. However, the OSPW toxicity toward goldfish primary kidney macrophages after solar/chlorine treatment showed no obvious toxicity reduction versus that of untreated OSPW, which warrants further study for process optimization.

Assessment of photochemical processes in marine oil spill fingerprinting

Understanding weathering processes plays a critical role in oil spill forensics, which is based on the comparison of the distributions of selected compounds assumed to be recalcitrant and/or have consistent weathering transformations. Yet, these assumptions are based on limited laboratory and oil-spill studies. With access to additional sites that have been oiled by different types of oils and exposures, there is a great opportunity to expand on our knowledge about these transformations. Here, we demonstrate the effects of photooxidation on the overall composition of spilled oils caused by natural and simulated sunlight, and particularly on the often used polycyclic aromatic hydrocarbons (PAHs) and the biomarker triaromatic steranes (TAS). Both laboratory and field data from oil released from the Macondo well oil following the Deepwater Horizon disaster (2010), and heavy fuel-oil from the Prestige tanker spill (2002) have been obtained to improve the data interpretation of the typical fingerprinting methodology.

Photolytic and photocatalytic degradation of surface oil from the Deepwater Horizon spill

The photochemical behavior of Deepwater Horizon oil collected from the surface of the Gulf of Mexico was studied. Thin oil films on water were subjected to simulated sunlight, and the resulting chemical and optical changes were observed. Polycyclic aromatic hydrocarbons (PAHs) showed substantial photodegradation, with larger PAHs being more rapidly decomposed. About 60% of the fluorescence at the excitation and emission maxima was observed with 12h of simulated solar irradiation equivalent to approximately 3d of sunlight. Synchronous scan fluorescence measurements showed 80-90% loss of larger PAHs with 12h of simulated solar irradiation. Absorbance of the oil decreased by only 20% over the same time period. Alkanes showed no significant photochemical losses. After irradiation, the toxicity of water in contact with the oil significantly increased, presumably due to the release of water soluble photoproducts that were toxic. Photocatalyst addition resulted in enhanced degradation rate for PAHs, and toxicity of the aqueous layer was altered in the presence of photocatalysts added to the oil film. Photochemistry is an important pathway for degradation of large PAHs, which are typically resistant to biodegradation.

High-molecular weight sulfur-containing aromatics refractory to weathering as determined by Fourier transform ion cyclotron resonance mass spectrometry

Biomarkers and low-molecular weight polyaromatic compounds have been extensively studied for their fate in the environment. They are used for oil spill source identification and monitoring of weathering and degradation processes. However, in some cases, the absence or presence of very low concentration of such components restricts the access of information to spill source. Here we followed the resistance of high-molecular weight sulfur-containing aromatics to the simulated weathering condition of North Sea crude oil by ultra high-resolution Fourier transform ion cyclotron resonance mass spectrometry. The sulfur aromatics in North Sea crude having double bond equivalents (DBE) from 6 to 14 with a mass range 188-674Da were less influenced even after 6 months artificial weathering. Moreover, the ratio of dibenzothiophenes (DBE 9)/naphthenodibenzothiophenes (DBE 10) was 1.30 and 1.36 in crude oil and 6 months weathered sample, respectively reflecting its weathering stability. It also showed some differences within other oils. Hence, this ratio can be used as a marker of the studied crude and accordingly may be applied for spilled oil source identification in such instances where the light components have already been lost due to environmental influences.

Products of polycyclic aromatic sulfur heterocycles in oil spill photodegradation

Photo-oxidation is a potentially significant process in the degradation of crude oil spilled in the environment. The polycyclic aromatic sulfur heterocycles (PASHs) in an Egyptian crude oil (0.8 % sulfur) were photo-oxidized as a film on the surface of water in the presence of anthraquinone as photosensitizer under simulated solar irradiation. The polar photoproducts were characterized using negative ion electrospray ionization with time of flight mass spectrometry and, after trimethylsilylation, gas chromatography with mass spectrometry. The photoproducts identified revealed the presence of a large variety of sulfonic acids, aliphatic and aromatic acids, and alcohols. The data also give new information on the substituents of the aromatic compounds in the unexposed oil and indicate the presence of cyclohexyl substituted aromatic compounds.

Heterogeneous photocatalytic reactions of sulfur aromatic compounds

Sulfur aromatic compounds, such as mono-, di-, tri-, and tetraalkyl-substituted thiophene, benzothiophenes, dibenzothiophenes, are the molecular components of many fossils (petroleum, oil shale, tar sands, bitumen). Structural units of natural, cross-linked heteroaromatic polymers present in brown coals, turf, and soil are similar to those of sulfur aromatic compounds. Many sulfur aromatic compounds are found in the streams of petroleum refining and upgrading (naphthas, gas oils) and in the consumer products (gasoline, diesel, jet fuels, heating fuels). Besides fossils, the structural fragments of sulfur aromatic compounds are present in molecules of certain organic semiconductors, pesticides, small molecule drugs, and in certain biomolecules present in human body (pheomelanin pigments). Photocatalysis is the frontier area of physical chemistry that studies chemical reactions initiated by absorption of photons by photocatalysts, that is, upon electronic rather than thermal activation, under "green" ambient conditions. This review provides systematization and critical review of the fundamental chemical and physicochemical information on heterogeneous photocatalysis of sulfur aromatic compounds accumulated in the last 20-30 years. Specifically, the following topics are covered: physicochemical properties of sulfur aromatic compounds, major classes of heterogeneous photocatalysts, mechanisms and reactive intermediates of photocatalytic reactions of sulfur aromatic compounds, and the selectivity of these reactions. Quantum chemical calculations of properties and structures of sulfur aromatic compounds, their reactive intermediates, and the structure of adsorption complexes formed on the surface of the photocatalysts are also discussed.