The Elovich Equation in Chemisorption Kinetics

Unleashing the Potential of Tailored ZnO-MgO Nanocomposites for the Enhancement of NO2 Sensing Performance at Room Temperature

Surface functionalization of semiconducting metal oxides has emerged as a highly effective approach for enhancing their sensing capabilities. In the present work, the surface of randomly oriented zinc oxide (ZnO) nanowires is modified with an optimized thickness (7 nm) of magnesium oxide (MgO), which exhibits an exceptionally sensitive and selective behavior toward NO2 gas, yielding a response of approximately 310 for 10 ppm concentration at room temperature. The synergistic interplay between ZnO and MgO leads to a remarkable 20-fold improvement in sensor response compared to a pristine ZnO film and allows the detection of concentrations as low as 50 ppb. The ZnO-MgO composite was characterized using X-ray diffraction (XRD), XPS, and SEM-EDS to gain structural, compositional, and morphological insights. The interaction of the NO2 molecule with the sensor film was investigated using density functional theory (DFT) simulations, revealing that oxygen vacant sites on the MgO surface are most favorable for NO2 adsorption, with an adsorption energy of -3.97 eV and a charge transfer of 1.74e toward NO2. The XPS, photoluminescence (PL), and EPR measurements experimentally verified the presence of oxygen vacancies in the sensing material. The introduction of localized levels within the band gap by oxygen vacancies significantly promotes the interaction of gas molecules with these sites, which enhances the charge transfer toward NO2 gas molecules. This augmentation has a profound influence on the space charge region at the ZnO-MgO interface, which is pivotal for modulating the charge transport in the ZnO layer, resulting in the substantial improvement of NO2 response at room temperature.

An Effective Sol-Gel-Functionalized Polyurethane Foams Solid Platform Packed Minicolumns for Complete Extraction of Chromium (VI) from Water: Kinetic, Sorption Isotherms, Thermodynamic Study, and Analytical Utility

In the modern era, sol-gel plays a key role in the progress of a new generation of dispersive solid-phase microextractors (d-µ SPMEs) for the removal of organic and inorganic pollutants in complex matrices. Thus, the current study reports the use of sol-gel-functionalized polyurethane foams (PUFs) as a novel solid platform for complete extraction of chromium (VI) species from aqueous media. The planned protocol was based upon the complete extraction of the formed binary complex ion associates between the protonated ether and/or urethane groups of PUFs and chlorochromate anion [CrO3Cl]- aq in aqueous HCl (≥1M) medium in addition to H-bonding and the electrostatic π-π interaction that resulted between the CrO3Cl- and the silanol group (Si/ZrO2, Si-O-Zr) and siloxane (Si-O-Si) groups of the sol-gel. The impact of the analytical parameters (solution pH, natural mineral acids, shaking time, temperature, and chromium (VI) concentrations) was critically studied. At the optimal conditions, the uptake capacity of the established extractor (9.9 mg·g-1) was in agreement with the Langmuir adsorption capacity (12.08 mg·g-1) of the monolayer. The sorption data fitted well with the pseudo first-order kinetic model (R 2 = 0.9961) with an overall rate constant (k 1) of 0.081 min-1 and an equilibrium capacity (q e ) of 8.6 mg·g-1, which is in a good agreement with the experimental value (9.9 mg·g-1). The sorption of the oxyion [CrO3Cl]- aq onto the solid sorbent is an endothermic and spontaneous process as reflected from the values of ΔH (6.99 kJ·mol-1) and ΔG (-8.14 kJ·mol-1 at 293 K), respectively. The ΔS value (15.13 kJ·mol-1·K-1) reflects that the [CrO3Cl]- aq retention onto the sol-gel-treated PUFs sorbent proceeded in a more unplanned fashion. Sol-gel-treated PUFs sorbent-packed minicolumns were successfully used for the complete removal of trace levels of chromium (VI) species from water samples. Sorbed chromium (VI) species were recovered with NaOH (0.5 M) and analysed by spectrophotometry, which supports the utility of the sol-gel-treated PUFs as a low-cost solid extractor for water treatment.

Comprehensive investigation of isotherm, RSM, and ANN modeling of CO2 capture by multi-walled carbon nanotube

Chemical vapor deposition was used to produce multi-walled carbon nanotubes (MWCNTs), which were modified by Fe-Ni/AC catalysts to enhance CO2 adsorption. In this study, a new realm of possibilities and potential advancements in CO2 capture technology is unveiled through the unique combination of cutting-edge modeling techniques and utilization of the recently synthesized Fe-Ni/AC catalyst adsorbent. SEM, BET, and FTIR were used to analyze their structure and morphology. The surface area of MWCNT was found to be 240 m2/g, but after modification, it was reduced to 11 m2/g. The modified MWCNT showed increased adsorption capacity with higher pressure and lower temperature, due to the introduction of new adsorption sites and favorable interactions at lower temperatures. At 25 °C and 10 bar, it reached a maximum adsorption capacity of 424.08 mg/g. The optimal values of the pressure, time, and temperature parameters were achieved at 7 bar, 2646 S and 313 K. The Freundlich and Hill models had the highest correlation with the experimental data. The Second-Order and Fractional Order kinetic models fit the adsorption results well. The adsorption process was found to be exothermic and spontaneous. The modified MWCNT has the potential for efficient gas adsorption in fields like gas storage or separation. The regenerated M-MWCNT adsorbent demonstrated the ability to be reused multiple times for the CO2 adsorption process, as evidenced by the study. In this study, a feed-forward MLP artificial neural network model was created using a back-propagation training approach to predict CO2 adsorption. The most suitable and efficient MLP network structure, selected for optimization, consisted of two hidden layers with 25 and 10 neurons, respectively. This network was trained using the Levenberg-Marquardt backpropagation algorithm. An MLP artificial neural network model was created, with a minimum MSE performance of 0.0004247 and an R2 value of 0.99904, indicating its accuracy. The experiment also utilized the blank spreadsheet design within the framework of response surface methodology to predict CO2 adsorption. The proximity between the Predicted R2 value of 0.8899 and the Adjusted R2 value of 0.9016, with a difference of less than 0.2, indicates a high level of similarity. This suggests that the model is exceptionally reliable in its ability to predict future observations, highlighting its robustness.

Hair relaxation after shaping - A kinetic approach

OBJECTIVE

Hair fibres have been shaped via either a thermal route or via a chemical route. The time-relaxation transients of the shaped hairs in air, and in water, respectively, were evaluated. The collected data were kinetically modelled in order to reveal information about the rate controlling mechanism of the recovery process.

METHODS

Hair fibres were thermally shaped at different temperatures between heated plates and left to relax in an environment of controlled humidity and temperature. Different hair fibres were chemically shaped and left to relax in water of different controlled temperatures. Relaxation data were used for modelling the kinetics of the recovery processes by using exponential and logarithmic kinetic laws. The fitting of the models to the two sets of data has been checked by using the residual sum of squares for matching the proper model to each set of data.

RESULTS

The processes of shaping and recovery were assimilated with a sequence of two successive quasi-chemical reactions, occurring at the used temperatures. Based on chemical and physical assumptions, the two groups of experiments were modelled by two different laws: an exponential law, suggesting a first-order process as the rate-determining step of the relaxation of thermally shaped fibres, and a logarithmic law, suggesting a slow relaxation, based on percolation theory, for the chemically shaped fibres. This allowed use of chemical kinetics tools for calculating the values of the activation energy in each case. The evaluated values of activation energy of the relaxation processes for both thermal and chemical shaping were found to be close to each other, in spite of the different methods of shaping.

CONCLUSION

The kinetic analysis suggests that despite different reaction sequences occurring during the different shaping-relaxation processes, the rate-controlling mechanism that manages the recovery process is the same in all cases; and this process is proposed to be the thiol-disulphide reformation of intra-protein bonds inside hair.

Folic acid conjugated poly (Amidoamine) dendrimer grafted magnetic chitosan as a smart drug delivery platform for doxorubicin: In-vitro drug release and cytotoxicity studies

This study reports the development of a magnetic and pH-responsive nanocarrier for targeted delivery and controlled release of doxorubicin (DOX). A multifunctional magnetic chitosan nanocomposite (FA-PAMAMG2-MCS) was fabricated by grafting poly(amidoamine) dendrimer and folic acid onto the MCS surface for active targeting. DOX was loaded into this core-shell bio-nanocomposite via adsorption. Structural and morphological characterization of the prepared nanomaterials was performed using XRD, FT-IR, VSM, TGA, BET, FE-SEM/EDX, and TEM techniques. Adsorption capacity of the FA-PAMAMG2-MCS was optimized by changing diverse parameters, such as pH, initial drug concentration, temperature, contact time, and adsorbent dosage. The maximum adsorption capacity for DOX was 102.85 mg g-1 at 298 K. The in-vitro drug release curve at pHs 5.6 and 7.4 manifested a faster drug release from the prepared nanocarrier in acidic environments and, conversely, a slower release in neutral environments over 48 h. The release kinetics followed Peppas-Sahlin models, showing non-Fickian behavior. Moreover, the in-vitro cytotoxicity studies against the human breast cancer (MDA-MB 231) cell line demonstrated the remarkable anticancer activity of the DOX@FA-PAMAMG2-MCS and declared its potency for nanomedicine applications. This multifunctional system could overcome limitations of conventional chemotherapeutic agents through pH-triggered drug release, enabling targeted cytotoxicity against cancer cells.

Bioremediation of uranium (Ⅵ) using a native strain Halomonas campaniensis ZFSY-04 isolated from uranium mining and milling effluent: Potential and mechanism

A significant surge in the exploitation of uranium resources has resulted in considerable amounts of radioactive effluents. Thus, efficient and eco-friendly uranium removal strategies need to be explored to ensure ecological safety and resource recovery. In this study, we investigated the resistance of Halomonas campaniensis strain ZFSY-04, isolated from an evaporation pool at a uranium mine site, and its potential mechanism of uranium (Ⅵ) removal. The results showed that the strain exhibited unique uranium tolerance and its growth was not significantly inhibited under a uranium concentration of 700 mg/L. It had a maximum loading capacity of 865.40 mg/g (dry weight), achieved following incubation under uranium concentration of 100 mg/L, pH 6.0, and temperature 30 °C, for 2 h, indicating that the removal of uranium by the strain was efficient and rapid. Combined with kinetic, isothermal, thermodynamic, and microspectral analyses, the mechanism of uranium loading by strain ZFSY-04 was metabolism-dependent and diverse, including, physical and chemical adsorption on the cell surface, extracellular biomineralisation, intracellular bioaccumulation, and biomineralisation. Our results highlight the unique properties of indigenous strains, including high resistance, high efficiency, rapid uranium removal, and various uranium removal strategies, which make it suitable as a new tool for in situ bioremediation and uranium-contaminated environmental resource recovery.

Effect of the magnetic core in alginate/gum composite on adsorption of divalent copper, cadmium, and lead ions in the aqueous system

The change of composition of an adsorbent material has been widely used as a method to increase its adsorption capacity, particularly concerning adsorbents made of polysaccharides. Introducing magnetic adsorbents into contaminated water treatment systems is a highly promising strategy, as it promotes the metal ions removal from water. Considering this, gum Arabic (GA) was associated with alginate (Alg), when magnetite nanoparticles were present or absent, to produce beads that were utilised to take up Cu(II), Cd(II), and Pb(II) from aqueous solution. After a complete characterisation (for which Fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and swelling were used), the adsorption properties were established using batch and column tests. The magnetic beads (MAlg/GA) demonstrated improved adsorption in comparison with the beads made without magnetite (Alg/GA) under the same conditions. In normal adsorption conditions (pH 6.0, 25 °C, 2.5 g L-1 of adsorbent dosage), the highest uptake capacities recorded for the MAlg/GA beads were: for Cu(II), 1.33 mmol g-1; Cd(II), 1.59 mmol g-1; and for Pb(II), 1.43 mmol g-1. The pseudo-second-order kinetics and Langmuir isotherm models provided good fits for the adsorption of these metals. Overall, ion exchange and physical forces led to the uptake of these metals by both Alg/GA and MAlg/GA; moreover, the functional groups on the beads played crucial roles as binding sites. Additionally, it was observed that flow rates of >2 mL min-1 did not produce noticeable changes in uptake levels over the same flow period. It was found that the efficient eluting agent was HNO3 (0.2 M). In some cases, the metals were not removed fully from the used beads during the first five cycles of regeneration and reuse. The results of this investigation show that these beads are efficient adsorbents for the removal of metal ions from spiked well water samples.

Release of molecules from nanocarriers

Release of drugs or vaccine molecules from macro-, micro-, and nano-sized carriers is usually considered to be limited by diffusion and/or carrier dissolution and/or erosion. The corresponding experimentally observed kinetics are customarily fitted by using the empirical Weibull and Korsemeyer-Peppas expressions. With decreasing size of carriers down to about 100 nm, the timescale of diffusion decreases, and accordingly the release can be kinetically limited, i.e., controlled by jumps of molecules located near the carrier-solution interface. In addition, nanocarriers (e.g., lipid nanoparticles) are often structurally heterogeneous so that the absorption of molecules there can be interpreted in terms of energetic heterogeneity, i.e., distribution of energies corresponding to binding sites and activation barriers for release. Herein, I present a general kinetic model aimed at such situations. For illustration, the deviation of the molecule binding energy from the maximum value was considered to be about 4-8 kcal mol-1. With this physically reasonable (for non-covalent interaction) scale of energetic heterogeneity, the predicted kinetics (i) are linear in the very beginning and then, with increasing time, become logarithmic and (ii) can be nearly perfectly fitted by employing the Weibull or Korsmeyer-Peppas expressions with the exponent in the range from 0.6 to 0.75. Such values of the exponent are often obtained in experiments and customarily associated with non-Fickian diffusion. My analysis shows that the energetic heterogeneity can be operative here as well.

Combination of adsorption/desorption and photocatalytic reduction processes for PFOA removal from water by using an aminated biosorbent and a UV/sulfite system

Per- and polyfluoroalkyl substances (PFAS) are stable organic chemicals, which have been used globally since the 1940s and have caused PFAS contamination around the world. This study explores perfluorooctanoic acid (PFOA) enrichment and destruction by a combined method of sorption/desorption and photocatalytic reduction. A novel biosorbent (PG-PB) was developed from raw pine bark by grafting amine groups and quaternary ammonium groups onto the surface of bark particles. The results of PFOA adsorption at low concentration suggest that PG-PB has excellent removal efficiency (94.8%-99.1%, PG-PB dosage: 0.4 g/L) to PFOA in the concentration range of 10 μg/L to 2 mg/L. The PG-PB exhibited high adsorption efficiency regarding PFOA, being 456.0 mg/g at pH 3.3 and 258.0 mg/g at pH 7 with an initial concentration of 200 mg/L. The groundwater treatment reduced the total concentration of 28 PFAS from 18 000 ng/L to 9900 ng/L with 0.8 g/L of PG-PB. Desorption experiments examined 18 types of desorption solutions, and the results showed that 0.05% NaOH and a mixture of 0.05% NaOH + 20% methanol were efficient for PFOA desorption from the spent PG-PB. More than 70% (>70 mg/L in 50 mL) and 85% (>85 mg/L in 50 mL) of PFOA were recovered from the first and second desorption processes, respectively. Since high pH promotes PFOA degradation, the desorption eluents with NaOH were directly treated with a UV/sulfite system without further adjustment. The final PFOA degradation and defluorination efficiency in the desorption eluents with 0.05% NaOH + 20% methanol reached 100% and 83.1% after 24 h reaction. This study proved that the combination of adsorption/desorption and a UV/sulfite system for PFAS removal is a feasible solution for environmental remediation.

High efficient removal of 4-aminophenylarsonic acid from aqueous solution via enhanced FeOOH using Mn(VII)

Efficient removal of 4-aminophenylarsonic acid from contaminated water sources is essential to mitigate arsenic pollution. We proposed a competent technique to achieve 4-aminophenylarsonic acid removal via adsorption on enhanced α-FeOOH using various concentrations of Mn(VII). The elimination rate of 4-aminophenylarsonic acid applying FeOOH with Mn(VII) was dependent on acidic conditions. More than 99.9% of 4-aminophenylarsonic acid was eliminated in a 6-min reaction time under acidic conditions. The reaction of 4-aminophenylarsonic acid was fast at 4.0 and 5.0 pH, with its complete oxidation into arsenate and the liberation of manganese Mn(II) in the initial stage of the reaction. Similarly, the reaction rate constant (k_obs) decreased from 0.7048 ± 0.02 to 0.00155 ± 0.00007 as the pH increased from 4.0 to 9.0. Oxidation capacity was considerably enhanced via the removal of electrons from 4-aminophenylarsonic acid to Mn(VII) after the creation of its radical intermediate and further change in Mn(III) to Mn(II) in the solution. The results showed that Mn(VII) played a crucial role in 4-aminophenylarsonic acid degradation at a low pH (e.g., 4.0), and the oxidation process proceeded in different manners, namely, electron transfer, hydroxylation, and ring-opening. These results illustrated that Mn(VII) is an effective, economic purification process to mitigate 4-aminophenylarsonic acid generated from poultry waste.

Preparation of a Polyaniline-Modified Hybrid Graphene Aerogel-Like Nanocomposite for Efficient Adsorption of Heavy Metal Ions from Aquatic Media

This paper considers the synthesis of a novel nanocomposite based on reduced graphene oxide and oxidized carbon nanotubes modified with polyaniline and phenol-formaldehyde resin and developed through the carbonization of a pristine aerogel. It was tested as an efficient adsorbent to purify aquatic media from toxic Pb(II). Diagnostic assessment of the samples was carried out through X-ray diffractometry, Raman spectroscopy, thermogravimetry, scanning and transmission electron microscopy, and infrared spectroscopy. The carbonized aerogel was found to preserve the carbon framework structure. The sample porosity was estimated through nitrogen adsorption at 77 K. It was found that the carbonized aerogel predominantly represented a mesoporous material having a specific surface area of 315 m²/g. After carbonization, an increase in smaller micropores occurred. According to the electron images, the highly porous structure of the carbonized composite was preserved. The adsorption capacity of the carbonized material was studied for liquid-phase Pb(II) extraction in static mode. The experiment results showed that the maximum Pb(II) adsorption capacity of the carbonized aerogel was 185 mg/g (at pH 6.0). The results of the desorption studies showed a very low desorption rate (0.3%) at pH 6.5 and a rate of about 40% in a strongly acidic medium.

Adsorption of flupyradifurone onto soils: kinetics, isotherms, and influencing factors

The study of the adsorption properties of pesticides in soil is essential to assessing the risk of their pollution of nearby aquatic environments. To reveal the adsorption mechanisms of flupyradifurone (FPO) on soil, batch experiments in five different soils were carried out in this study. The adsorption kinetics and isotherms of FPO in five soils were well fitted by using several models (R² = 0.922-0.998). It was found that both physical and chemical adsorption were included in the adsorption process of FPO in soils; the monolayer adsorption of FPO occurred with a non-uniform energy distribution on the soil surface, and the internal particle diffusion was not the only rate-controlling step. The adsorption coefficients calculated by using the Langmuir (K_L) and Freundlich (K_F) models were 0.0158-0.0982 and 1.053-9.798, respectively. In addition, the main factors affecting the adsorption of FPO in soil were investigated by stepwise regression fitted with the adsorption coefficient (K_d) and the soil properties. It was found that the organic carbon content was the main factor (R² = 0.857, p < 0.05). Therefore, the organic carbon adsorption coefficients (K_oc) were calculated. The results (1.0532-5.6529) indicated that FPO has a low affinity and high mobility in the soils, and may cause water environment pollution around the soil. Therefore, FPO should be used cautiously in paddy fields. These research findings were important for elucidating the sorption behaviour and transport of FPO in soil.

Fabrication and investigation of novel monochloroacetic acid fortified, tripolyphosphate-crosslinked chitosan for highly efficient adsorption of uranyl ions from radioactive effluents

Chitosan crosslinked with potassium tripolyphosphate (CTPP) and monochloroacetic-acid-modified chitosan crosslinked with potassium tripolyphosphate (MCTPP) were synthesized for removing UO₂²⁺ from acidic radioactive effluents. The influential factors, operational requirements, and interactive mechanisms of the adsorption process were systematically investigated. The mesh-structured composites adsorbed UO₂²⁺ most effectively at pH 5.0. The maximum adsorption capacities for pure chitosan, CTPP, and MCTPP were 374.93, 780.89, and 1487.72 mg/g, respectively. Batch experiments indicated that the pH and adsorbent dose strongly influenced UO₂²⁺ adsorption. MCTPP could adsorb most UO₂²⁺ within 15 min, and equilibrium was reached by ~1 h. The adsorption isotherms indicated that UO₂²⁺ adsorption by MCTPP may be an endothermic single-layer adsorption process. Moreover, common metal ions in single-metal systems only slightly affected this process. The results of instrumental characterization and natural water application suggested that the highly developed pore structure and abundant tripolyphosphate groups in synthesized composites were dominant adsorption contributors besides amino and hydroxyl groups. Successful development of the novel material for efficiently adsorbing UO₂²⁺ and identification of the adsorption mechanism will provide valuable guidance to chitosan modification and further remediation practices of radioactive effluents.

Competitive kinetics of adsorption onto activated carbon for emerging contaminants with contrasting physicochemical properties

Activated carbon (AC) can be used for the removal of emerging contaminants (e.g., drugs) in water and wastewater treatment plants. In the present study, we investigated the performance of two ACs (from coconut shell and Pinnus sp.) in the adsorption of caffeine, carbamazepine, and ricobendazole considering the compounds separately and in combination in batch-scale experiments. The concentrations of the drugs were determined by a validated method using solid-phase extraction with on-line ultra-high performance liquid chromatography-tandem mass spectrometry. The most mesoporous AC provided higher drug removal. The kinetic data were described by the pseudo-second-order, Elovich, and Weber-Morris models, while the adsorption isotherms showed a better fit to the Freundlich model, indicative of multilayer adsorption. The Dubinin-Radushkevich model was used as a first approach to estimate the mean adsorption energy (E) and the results indicate that chemisorption governed the adsorption process, with E higher than 8 kJ mol^-1. In the multicomponent assays, the adsorption of caffeine showed the greatest hindrance caused by the presence of other drugs. Multicomponent assays are fundamental to evaluate the potential adsorption capacity in real water treatment plants. Our study suggests that drugs with different structures and physicochemical properties may interact differently with ACs, especially in multicomponent solutions, with important implications for the design (e.g., volumes and areas of treatment plants) and operation (e.g., water residence time) of the treatment plants.

Adsorption Behaviors of Cationic Methylene Blue and Anionic Reactive Blue 19 Dyes onto Nano-Carbon Adsorbent Carbonized from Small Precursors

In this work, an innovative nano-carbon material (N-CM) adsorbent was reported for exploring its adsorption behaviors toward cationic methylene blue (MB) and anionic reactive blue 19 (RB19) pollutants. The proposed N-CM was synthesized by a one-step solvothermal treatment of citric acid and zinc gluconate small precursors. N-CM consists of nanosheets that have an advantageous specific surface area, large sp2/sp3 hybridized domains, and abundant nitrogen/oxygen-containing surface functional groups. The synergistic effects of these features are conducive to the MB and RB19 adsorption. Different from anionic RB19 adsorption (79.54 mg/g) by the cooperative π-π stacking and hydrogen bonding, cationic MB adsorbed onto N-CM mainly by the electrostatic attraction at the natural pH solution (> pHpzc), with an adsorption capacity up to 118.98 mg/g. Interestingly, both MB and RB19 adsorption conformed to the pseudo-second order kinetic (R2 ≥ 0.995) and Langmuir isothermal (R2 ≥ 0.990) models, accompanied by similar maximum monolayer adsorption capacities of 120.77 and 116.01 mg/g, respectively. Their adsorption processes exhibited spontaneously endothermic characteristics. Moreover, N-CM showed superior selective capability toward MB in different mixed dye systems, with high removal efficiencies of 73−89%. These results demonstrate that the high-performance carbon adsorbent prepared from small precursors via low-temperature carbonization shows great potentials in wastewater treatment.

Recent Advances on Innovative Materials from Biowaste Recycling for the Removal of Environmental Estrogens from Water and Soil

New technologies have been developed around the world to tackle current emergencies such as biowaste recycling, renewable energy production and reduction of environmental pollution. The thermochemical and biological conversions of waste biomass for bioenergy production release solid coproducts and byproducts, namely biochar (BC), hydrochar (HC) and digestate (DG), which can have important environmental and agricultural applications. Due to their physicochemical properties, these carbon-rich materials can behave as biosorbents of contaminants and be used for both wastewater treatment and soil remediation, representing a valid alternative to more expensive products and sophisticated strategies. The alkylphenols bisphenol A, octylphenol and nonylphenol possess estrogenic activity comparable to that of the human steroid hormones estrone, 17β-estradiol (and synthetic analog 17α-ethinyl estradiol) and estriol. Their ubiquitous presence in ecosystems poses a serious threat to wildlife and humans. Conventional wastewater treatment plants often fail to remove environmental estrogens (EEs). This review aims to focus attention on the urgent need to limit the presence of EEs in the environment through a modern and sustainable approach based on the use of recycled biowaste. Materials such as BC, HC and DG, the last being examined here for the first time as a biosorbent, appear appropriate for the removal of EEs both for their negligible cost and continuously improving performance and because their production contributes to solving other emergencies, such as virtuous management of organic waste, carbon sequestration, bioenergy production and implementation of the circular economy. Characterization of biosorbents, qualitative and quantitative aspects of the adsorption/desorption process and data modeling are examined.

Cetylpyridinium Bromide/Polyvinyl Chloride for Substantially Efficient Capture of Rare Earth Elements from Chloride Solution

A new sorbent cetylpyridinium bromide/polyvinylchloride (CPB/PVC) was prepared and tested to extract rare earth elements (REEs) from their chloride solutions. It was identified by FTIR, TGA, SEM, EDX, and XRD. The impact of various factors such as pH, RE ion initial concentration, contacting time, and dose amount via sorption process was inspected. The optimum pH was 6.0, and the equilibrium contact time was reached at 60 min at 25 °C. The prepared adsorbent (CPB/PVC) uptake capacity was 182.6 mg/g. The adsorption of RE ions onto the CPB/PVC sorbent was found to fit the Langmuir isotherm as well as pseudo-second-order models well. In addition, the thermodynamic parameters of RE ion sorption were found to be exothermic and spontaneous. The desorption of RE ions from the loaded CPB/PVC sorbent was investigated. It was observed that the optimum desorption was achieved at 1.0 M HCl for 60 min contact time at ambient room temperature and a 1:60 solid: liquid phase ratio (S:L). As a result, the prepared CPB/PVC sorbent was recognized as a competitor sorbent for REEs.

Removal of copper from sulfate solutions using biochar derived from crab processing by-product

Increasing metal demand is accelerating the mining and processing of minerals, however to ensure sustainable growth innovative approaches are required to better manage associated effluents. Biochar from the fast pyrolysis of residues from fishery and forestry operations has been studied as a low-cost, environmentally and economically friendly method for treating mine tailings and processing effluents. However, the bulk of the studies focus on terrestrial biomass (e.g. wood) and do not include potential inhibition/enhancement of adsorption due to pH controlling compounds. In this work biochar generated from snow crab (Chionoecetes Opilio) processing was studied as an adsorbent for copper solutions containing sulfate (a key compound in sulfide ore mining waters) with the objective of assessing adsorption capacity and the impact of sulfate on copper adsorption. The biochar, a porous structure comprised of calcite (CaCO₃), was alkaline and has a negative zeta potential under neutral and basic conditions. The crab biochar removed over 99% of Cu²⁺ from a 100 mg/L solution (sourced as CuSO₄) at a dosage of 5 g/L, which was higher than lignocellulosic biochar at the same biochar dosage. While metal adsorption can often be impacted at acidic conditions, Cu²⁺ adsorption was not impacted by initial acidic pH due to the biochar's buffering capacity. The Pseudo-Second Order (PSO) model fit the adsorption rate with maximum adsorption achieved in approximately 2 h. The maximum adsorption isotherm capacity was 184.8 ± 10.2 mg/g for Cu²⁺, much higher than existing commercial activated carbons and previously studied lignocellulosic biochars and followed the Freundlich isotherm. The adsorption mechanism responsible for removal of Cu²⁺ was found to be precipitation, in the form of the mineral posnjakite (Cu₄[(OH)₆SO₄]·H₂O). These results indicate for the first time that crab-based biochars are capable of adsorbing large quantities of Cu²⁺ from sulfate-rich solution, while also buffering solution pH, demonstrating promise as an acid mine drainage treatment for removal of harmful metals and reduction of acidity.

How the Carbonization Time of Sugarcane Biomass Affects the Microstructure of Biochar and the Adsorption Process?

Biochars (BCs) are very versatile adsorbents, mainly, in the effectiveness of adsorption of organic and inorganic compounds in aqueous solutions. Here, the sugarcane biomass (SCB) was used to produce biochar at different carbonization times: 1, 2, 3, 4, and 5 h, denominated as BC1, BC2, BC3, BC4, and BC5, respectively. The superficial reactivity was studied with adsorption equilibrium experiments and kinetics models; Methylene Blue (MB) was used as adsorbate at different pH values, concentrations, and temperatures. In summary, the carbonization time provides the increase of superficial area, with exception of BC4, which decreased. Equilibrium studies showed inflection points and fluctuations with different initial dye concentration and temperature; SCB showed the best adsorption capacity compared to the BCs at the three temperatures tested, varying with the increase of MB concentration, suggesting the dependence of these two main factors on the adsorption process. The proposed adsorption mechanism suggests the major influence of Coulomb interactions, H-bonding, and π-interactions on the adsorption of MB onto adsorbents, evidencing that the adsorption is led by physical adsorption. Therefore, the results led to the use of the SCB without carbonization at 200 °C, saving energy and more adsorbent mass, considering that the carbonization influences weight loss. This study has provided insights of the use of SCB in MB dye adsorption as a low-cost and eco-friendly adsorbent.

Adsorption of Pb(II) from Water onto ZnO, TiO2, and Al2O3: Process Study, Adsorption Behaviour, and Thermodynamics

This study is aimed at comparing the use of zinc oxide (ZnO), titanium dioxide (TiO2), and aluminium oxide (Al2O3) for removing lead ions from water through adsorption. The point of zero charge was obtained for ZnO, TiO2, and Al2O3 and was found to be 7.3, 7.1, and 9.0, respectively. The effect of pH, adsorbent dose, contact time, initial concentrations, and temperature was investigated in batch experiments. The optimal conditions obtained were 7, 2 g/L, 120 mins, 100 ppm, and 41°C, respectively, where the optimal removal efficiencies were 98.43%, 96.45%, and 85.50% for ZnO, TiO2, and Al2O3, respectively. In addition, analyses of adsorption kinetics, mechanisms, isotherms, and thermodynamics were performed. The adsorption kinetics of Pb(II) were compared to popular models, and it was found that the pseudo-second-order (PSO) model best fitted the Pb(II) uptake for all adsorbents at correlation coefficient ( $R^2\ge 0.96$ ). The adsorption isotherms of Pb(II) were also compared to popular models, and it was found that the Pb(II) uptake by TiO2 and ZnO was well-described by the Langmuir model ( $R^2\ge 0.96$ ) with maximum adsorption capacities of 55.04 and 58.88 mg/g, respectively. On the other hand, the behaviour of Al2O3 is described more accurately by the Dubinin-Radushkevich (D-R) model ( $R^2=0.96$ ), and the maximum adsorption capacity was 53.64 mg/g. The isotherm analysis proved that the limiting step of the adsorption process is the film diffusion mechanism. In addition, studying the heat of adsorption of Pb(II) implied that the adsorption is endothermic due to the positive values of enthalpy ( $\Delta H^{°}\ge 30$ ) for all adsorbents. The absorbents were characterized using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX) to study the morphology of surfaces and the chemical characterization of the adsorbents to ensure that adsorption is achieved. ZnO showed better performance for the uptake of lead followed by TiO2 then Al2O3.

Fish scale-based biochar with defined pore size and ultrahigh specific surface area for highly efficient adsorption of ciprofloxacin

A fish scale-based porous activated biochar with defined pore size (DPBC) was fabricated by a one-step calcination and activation method. The DPBC possessed an ultrahigh specific surface area of 3370 m² g^-1 and its pore diameter centered at 1.49 nm which fits into the ciprofloxacin (CIP) molecular dimension, making it an ideal adsorbent for CIP adsorption due to the molecular pore-filling effect. The maximum Langmuir monolayer adsorption capacity of DPBC for CIP was higher than 1000 mg g^-1 and the equilibrium time was less than 4 h, superior to most adsorbents reported in literature. Thermodynamic analysis indicated the adsorption process was spontaneous and endothermic. Notably, fixed-bed experiments showed an encouraging adsorption performance towards CIP, with a high saturated dynamic adsorption capacity of 880.3 mg g^-1. Both Thomas and Yoon-Nelson models predict the fixed-bed column adsorption performance well. Hydrophobic effect, π-π interaction, π-π EDA, cation exchange, hydrogen bonding formation, pore filling effect, electrostatic and cation-π interaction involved in the CIP adsorption on the DPBC.

Adsorption of Yttrium Ions on 3-Amino-5-Hydroxypyrazole Impregnated Bleaching Clay, a Novel Sorbent Material

In this work, spent bleaching clay (SBC) was treated with ethyl acetate and impregnation with 3-amino-5-hydroxypyrazole (AHIBC) that utilized as economical sorbent material. The uptake of yttrium ions from aqueous solution using AHIBC was studied under batch process as a function of pH of the solution, contact time, adsorbent dosage, Yttrium ions concentration, and ambient temperature. The adsorption equilibrium was achieved at the value of pH = 6.0 and agitation time of 60 min at room temperature. The utmost adsorption capacity of Y(III) ions on AHIBC was 171.32 mg·g−1. Kinetic, isotherm, and thermodynamic models were applied to the experimental data obtained. Adsorption follows a pseudo–second–order kinetic model, while the adsorption isotherm fits the Langmuir model. A negative value of Gibbs free energy ΔG° revealed that the adsorption of the Y ions on the AHIBC adsorbent was spontaneously in nature. In addition, the electrostatic interaction process between the metal ions and AHIBC was favorable. The negative value of ΔH° states that Y ions adsorption was an exothermic process. Desorption efficiency reduced from 97% to 80% after eight consecutive rounds.

Preparation of Chitosan/Calcium Alginate/Bentonite Composite Hydrogel and Its Heavy Metal Ions Adsorption Properties

In order to avoid the secondary pollution of the toxic residue of chemical crosslinking agent accompanied by chemical hydrogel adsorbent and enhance the adsorption performance of physical hydrogel, chitosan/calcium alginate/bentonite (CTS/CA/BT) composite physical hydrogel was constructed. The formation mechanism and structure of the composite hydrogel were determined by FTIR, XRD and SEM. Adsorption performances of the hydrogel toward Pb2+, Cu2+ and Cd2+ in water under different condition as well as multi-ion competitive sorption were investigated. The adsorption processes were described with the canonical adsorption kinetics and isotherms models. With the utilization of XPS analysis and adsorption thermodynamics analysis, it was found that the adsorptions were spontaneous physico-chemical adsorptions. The results showed that the maximum adsorption capacity of the hydrogel for Pb2+, Cu2+ and Cd2+ reached up to 434.89, 115.30 and 102.38 mg·g-1, respectively, better than those of other physical hydrogels or chitosan/bentonite composite. Moreover, the composite hydrogel improved the collectability of bentonite and showed a good reusability. The modification of bentonite and the formation of hydrogel were completed simultaneously, which greatly simplifies the operation process compared with the prior similar works. These suggest that the CTS/CA/BT composite hydrogel has promising application prospects for removal of heavy metal ions from water.

Kinetic modelling of the uranium biosorption by Deinococcus radiodurans biofilm

Increasing number of reports on uranium contamination in groundwater bodies is a growing concern. Deinococcus radiodurans biofilm-based U(VI) bioremediation has great potential to provide solution. This study focuses on the kinetic modelling of uranium biosorption by D. radiodurans biofilm biomass and identification of the functional groups involved in the sequestration process. The effect of temperature, pH and amount of biofilm dry mass were studied using two uranyl ion concentrations (100 and 1000 mg/L). D. radiodurans dry biomass showed good affinity for uranyl ion adsorption. The kinetic experiments revealed that the biosorption process was spontaneous and exothermic in nature. The modelling of kinetic adsorption data revealed that U(VI) sorption by D. radiodurans biofilm biomass follows a pseudo-second-order reaction. Mechanism of U(VI) sorption was suggested to follow an intra-particle diffusion model, which includes covalent bonding between U(VI) and functional groups present on the surface of biofilm biomass, and diffusional barrier acts as a rate limiting step. External mass transfer was the rate-limiting step as evident from Boyd and Elovich plot. Chemical modifications in surface functional groups of biofilm biomass, confirmed the involvement of carboxyl, phosphate, and hydroxyl groups in uranium binding as a significant loss in U(VI) sorption capacity was recorded in these chemically modified biomasses. XRD data indicated the formation of metal deposits, predominantly as uranyl phosphates.

Chloride Removal of Calcium Aluminate-Layered Double Hydroxide Phases: A Review

Chlorine is a critical element with respect to the use of fossil fuel, recycling of industrial wastes, and water purification. Chlorine could form toxic chemical compounds, corrode pipe systems and boilers, and contaminate surface and ground waters. Calcium aluminate-layered double hydroxides are one of the most promising materials to remove chlorides due to the chemisorption mechanism, since the phases have positively charged interlayers. Many studies on the synthesis and the characterization of calcium aluminate-layered double hydroxides have been extensively conducted, whereas few studies have been conducted on the chloride removal characteristics of the phases. The state-of-the-art studies on the synthesis methods and the structural characteristics of CaAl-LDH phases, the underlying mechanism on the removal of chlorides, and the potential removal rate and the capacity in the present study were thoroughly reviewed.

Lignin-based magnetic activated carbon for p-arsanilic acid removal: Applications and absorption mechanisms

It is crucial for water environment security to remove its p-arsanilic acid (p-ASA) efficiently. Namely, removing p-arsanilic acid from aqueous media through magnetic separation, has become a novel method of removing toxic pollutants from water. Batch adsorption experiments demonstrated a higher adsorption of lignin-based magnetic activated carbon (201.64 mg g^-1) toward p-ASA. In addition, LMAC nanoparticles exhibited typical magnetism (35.63 emu g^-1 of saturation magnetization) and could be easily separated from the aqueous solution. Meanwhile, the endothermic adsorption of p-ASA over LMAC could spontaneously proceed and be well described by the pseudo-first-order and pseudo-second-order model as well as the intra-particle diffusion model. Moreover, the mechanisms during p-ASA adsorption over LMAC included the electrostatic attraction, surface complexation, π-π stacking and hydrogen bonding interaction. Importantly, lignin-based magnetic activated carbon has high absorbability and preferable reusability in real water samples. Consequently, this paper provides insights into preparation of the lignin-based magnetic activated carbon may be potential adsorbents for the remediation of organoarsenic compounds.

Leveraging re-chargeable nanobubbles on amine-functionalized ZnO nanocrystals for sustained ultrasound cavitation towards echographic imaging

Nanoparticles able to promote inertial cavitation when exposed to focused ultrasound have recently gained much attention due to their vast range of possible applications in the biomedical field, such as enhancing drug penetration in tumor or supporting ultrasound contrast imaging. Due to their nanometric size, these contrast agents could penetrate through the endothelial cells of the vasculature to target tissues, thus enabling higher imaging resolutions than commercial gas-filled microbubbles. Herein, Zinc Oxide NanoCrystals (ZnO NCs), opportunely functionalized with amino-propyl groups, are developed as novel nanoscale contrast agents that are able, for the first time, to induce a repeatedly and over-time sustained inertial cavitation as well as ultrasound contrast imaging. The mechanism behind this phenomenon is investigated, revealing that re-adsorption of air gas nanobubbles on the nanocrystal surface is the key factor for this re-chargeable cavitation. Moreover, inertial cavitation and significant echographic signals are obtained at physiologically relevant ultrasound conditions (MI < 1.9), showing great potential for low side-effects in in-vivo applications of the novel nanoscale agent from diagnostic imaging to gas-generating theranostic nanoplatforms and to drug delivery.

Kinetics of liquid phase batch adsorption experiments

Batch adsorption experiments are carried out by adding a known amount of adsorbent to a liquid solution at a known initial concentration and following the evolution in time of the concentration of the adsorbate. This is a very common method to obtain equilibrium and kinetic information in liquid systems, but in most cases kinetic results are analysed on the basis of empirical models. Two phenomenological models based on macropore diffusion in beads and shrinking core kinetics are used to generate data that are then interpreted with the widely used unconstrained linear regression methods. The results show that for both cases R2 values close to unity are obtained leading to the incorrect interpretation of the mechanism of mass transport. It is recommended that batch adsorption experiments should be analysed using phenomenological models to obtain physical parameters that are applicable to other systems and to reduce the experiments required to characterise fully the kinetics of adsorption.

A facile polymerisation of magnetic coal to enhanced phosphate removal from solution

Globally, there are increased threats to available freshwater resources due to pollution, climate change, and increased demand from population growth. Phosphorus is one of the essential nutrients required for animal and plant growth. However, when it is released into freshwater resources in excess amounts, it can become a pollutant through eutrophication. This study aimed to enhance the removal of phosphate from water using modified coal. The coal was magnetised by in-situ synthesis using a precipitation technique. To obtain functional groups and mechanical stability, magnetised coal particles were coated with polyaniline, via the polymerisation of aniline to form Magnetised Unburnt Coal Polyaniline (MUC-PANI). The properties of MUC-PANI were investigated using TGA, BET, XRD, Raman spectroscopy, SEM, and FTIR. TGA reviewed MUC-PANI as 58% magnetised coal and 42% polyaniline, while the specific surface area increased from 30.0 to 42.2 m²/g after modification. SEM indicated a cauliflower structure on the surface of MUC-PANI due to the successful polymerisation of polyaniline. The FTIR spectrum showed successful adsorption of phosphate due to the formation of incipient peak at1008 cm^-1. The adsorption kinetic data are better fitted to the Elovich model. The Langmuir adsorption capacity of MUC-PANI is 147.1 mg PO₄^3-/g at 25 °C and pH 5.0 (initial concentration 10-200 mg/L, dose 0.8 g/L). MUC-PANI is a cost-efficient compound for removal of phosphate because it is made from readily available coal.

Efficient removal of anti-inflammatory from solution by Fe-containing activated carbon: Adsorption kinetics, isotherms, and thermodynamics

This work developed an innovative activated carbon (ICAC) derived from orange peels (OP) through chemical activation using FeCl₃. The traditional activated carbon (PCAC) that was prepared through K₂CO₃ activation served as a comparison. Three adsorbents (ICAC, PCAC, and OP) were characterized by various techniques, these being: Brunauer-Emmett-Teller (BET) surface area analysis, thermo-gravimetric analysis, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, and Fourier transform infrared spectroscopy. They were applied to remove diclofenac from aqueous solution applying batch experiments, in order to investigate the characteristics of adsorptive kinetics, isotherms, and thermodynamics. Results indicated that the S_BET values were in the following order: 457 m²/g (PCAC) > 184 m²/g (ICAC) > 3.56 m²/g (OP). The adsorption process reached a fast equilibrium, with activating energies being 27.6 kJ/mol (ICAC), 16.0 kJ/mol (OP), and 11.2 kJ/mol (PCAC). The Langmuir adsorption capacities at 30 °C exhibited the decreasing order: 144 mg/g (ICAC) > 6.44 mg/g (OP) > 5.61 mg/g (PCAC). The thermodynamic parameters demonstrated a signal dissimilarity between biosorbent (ΔG° <0, ΔH° <0, and ΔS° <0) and activated carbon samples (ΔG° <0, ΔH° >0, and ΔS° >0). The presence of iron (FeOCl, γ-Fe₂O₃, and FeOOH) on the surface of ICAC played a determining role in efficiently removing diclofenac from solution. The excellent adsorption capacity of ICAC toward diclofenac resulted presumably from the contribution of complicated adsorption mechanisms, such as hydrogen bonding, ion-dipole interaction, π-π interaction, pore filling, and possible Fenton-like degradation. Therefore, FeCl₃ can serve as a promising activating agent for AC preparation with excellent efficiency in removing diclofenac.

Characterization and Adsorption Behavior of Strontium from Aqueous Solutions onto Chitosan-Fuller's Earth Beads

Fuller's earth spherical beads using chitosan as a binder were prepared for the removal of strontium ions from aqueous solution. The adsorbents were characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), which revealed the porous nature of the beads. The Brunauer⁻Emmett⁻Teller (BET) surface area of the beads was found to be 48.5 m²/g. The adsorption capacities of the beads were evaluated under both batch and dynamic conditions. The adsorption capacity was found to be ~29 mg/g of adsorbent at 298 K when the equilibrium concentration of strontium in the solution was 925 mg/L at pH 6.5. The X-ray photoelectron spectroscopy (XPS) data suggest that strontium uptake by the beads occurs mainly through an ion-exchange process. Kinetic data indicate that the sorption of strontium onto the beads follows anomalous diffusion. Thermodynamic data suggest that the ion-exchange of Sr²⁺ on the bead surface was feasible, spontaneous and endothermic in nature.

Adsorption removal of cationic dyes from aqueous solutions using ceramic adsorbents prepared from industrial waste coal gangue

Industrial solid waste coal gangue has huge utilization potential. Low-cost ceramic microsphere adsorbents were prepared from coal gangue by spray drying and sintering method and applied to remove cationic red X-5GN and cationic blue X-GRRL from aqueous solutions. The structural properties of the adsorbents were characterized. Adsorption kinetics, adsorption isotherms and effect of solution pH were studied. Adsorption mechanism and disposal of the spent adsorbents were also discussed. The results showed that the adsorption capacity of the cationic red and cationic blue onto the ceramic adsorbents was 1.044 mg g^-1 and 2.170 mg g^-1 respectively, according to the Langmuir model. The adsorption equilibrium time was quickly reached with the removal of both dyes over 90% within 1 min. The adsorbents exhibited favorable applicability with varying solution pH. Electrostatic attractions, n-π interactions and hydrogen bonding were proposed to be involved in the adsorption process based on the adsorption behavior. Using coal gangue ceramic adsorbents to treat colored wastewater could achieve the purpose of treating wastes with wastes. Therefore, the gangue adsorbent has promising application prospects for its comprehensive economic and environmental benefits.

One-step fabrication of functionalized poly(l-lactide) porous fibers by electrospinning and the adsorption/separation abilities

In this work, novel functionalized poly(l-lactide) (F-PLLA) porous fibers were fabricated through electrospinning using the PLLA/methylene chloride (CH₂Cl₂)/N,N-dimethylformamide (DMF) solution containing diethylenetriamine (DETA) and γ-aminopropyltriethoxysilane (KH-550). The effects of PLLA, DETA and KH-550 contents on the morphologies of the electrospun fibers were systematically investigated, and the results showed that at PLLA, DETA and KH-550 contents of 20% w/v, 2 wt% and 3 wt%, respectively, the electrospun F-PLLA fibers exhibited the homogeneous distribution of fiber diameters and the homogeneous porous structure on the fiber surface. Nitrogen-containing groups were successfully introduced to the electrospun fibers, which induced the great improvement of the hydrophilicity of the membrane surface. Adsorption measurements showed that the electrospun F-PLLA membrane had good adsorption ability toward Congo red (CR), and the adsorption capacity at room temperature was enhanced in 16 times compared with the common PLLA fiber membrane, and the maximum adsorption capacity was 135.7 mg g^-1. Furthermore, the adsorption behavior could be well described by the pseudo second-order model. Oil/water separating measurements showed that the electrospun F-PLLA membrane exhibited high separation efficiency and the maximum water fluxes were 2018 and 1861 L m^-2  h^-1 in separating non-emulsified and emulsified oil/water system under atmospheric pressure, respectively.

Release and kinetics of arsenic and plumbum in the Songhua River surficial sediments

To estimate the pollution of As and Pb in the Songhua River which flows through the major rice-producing regions in China, the present study investigated the level and release of As and Pb in surficial sediments which collected from nine sites in Songhua River (M₁-M₉). The concentration of As and Pb was ranged as follows: As = 3.104~15.01 μg/g, Pb = 20.10~37.42 μg/g; the average concentration: As = 6.466 ± 3.077 μg/g, Pb = 28.88 ± 5.077 μg/g. By analysis vertically, the average concentration of As was 5.166 ± 1.496 μg/g in the upstream, 5.815 ± 1.793 μg/g in the midstream, and 9.716 ± 4.977 μg/g in the downstream. The average concentration of Pb was 27.83 ± 4.552 μg/g in the upstream, 28.66 ± 6.333 μg/g in the midstream, and 30.99 ± 4.837 μg/g in the downstream. It indicated that the concentration of As and Pb increased gradually from upstream to downstream. As existed mainly as insoluble state and Pb existed mainly as sulfide and organic combining state in surficial sediments, and the species of As and Pb could transform with the change of the circumstance. The release of quantity of As was higher than Pb. The pH of 6 was not conducive to the release of As and Pb. When the temperature was 35 and 6 °C, the release of As and Pb in surficial sediments were restrained, respectively. Fumaric acid and citric acid played an important role in promoting the release of As, but not conducive to Pb. Furthermore, the reasonable aeration rate was beneficial to the release process of As and Pb in surficial sediment. By kinetic analysis, the Elovich equation (Ct = 84.931-8.952lnt) could be used to describe the dynamic process of the release of As in a relatively short time. The Elovich equation (C _t  = 2.724 + 1.3724lnt) and double constant rate equation (lnC _T  = 1.4646 + 0.1522lnT) could well describe the dynamics process of the release of Pb.

The removal efficiency and insight into the mechanism of para arsanilic acid adsorption on Fe-Mn framework

Para arsanilic acid (p-ASA) is extensively used as feed additives in poultry industry, resulting contaminates soil and natural water sources through the use of poultry litter as a fertilizer in croplands. Thus, removal of p-ASA prior to its entering environments is significant to control their environmental risk. Herein, we studied Fe-Mn framework and cubic Fe(OH)₃ as promising novel adsorbents for the removal of p-ASA from aqueous solution. The chemical and micro-structural properties of Fe-Mn framework and cubic Fe(OH)₃ materials were characterized by X-ray diffraction patterns (XRD), nitrogen adsorption (S_BET), zeta (ζ-) potential, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectra (XPS). The maximum adsorption capacity for p-ASA on Fe-Mn framework and cubic Fe(OH)₃ was determined to be 1.3mmolg^-1 and 0.72mmolg^-1 at pH4.0, respectively. Adsorption of p-ASA decreased gradually with increasing pH indicated that adsorption was strongly pH dependent. Azophenylarsonic acid was identified as an oxidation intermediate product of p-ASA after adsorption on Fe-Mn framework. Plausible removal mechanism for p-ASA by Fe-Mn framework was proposed. The obtained results gain insight into the potential applicability of Fe-Mn framework, which can be potentially important for the removal of p-ASA from water.