Behaviour and mechanics of phenolic sorption by novel bio-based graphene derivatives as adsorbents

Phenolic compounds, notorious for their environmental and health hazards, demand efficient removal from wastewater. Our research leads in synthesizing bio-based graphene derivatives from biomass-derived lignin, such as graphene oxide (bGO) and reduced graphene oxide (brGO), and these materials show promise in effectively removing hydrophobic pollutants like phenol and tannic acid. Hence, this study investigated the mechanical and dynamical aspects of their sorptions by bGO and brGO. Both adsorbents demonstrated a comparable adsorption pattern, with enhanced efficiency observed at higher adsorbent dosage, prolonged contact time, neutralized pH solutions, and elevated temperatures. Of note, phenol is removed at a much greater rate (>94%) than tannic acid (>84%) by both adsorbents at a dosage of 180 mg L-1, pH 6.5, 900 min, and 25 °C. The Freundlich model provided the best fit for the isotherm data of both phenol (R2 = 0.99) and tannic acid (R2 = 0.98), while the pseudo-second-order model effectively described the adsorption kinetics of phenol (R2 = 0.99) and tannic acid (R2 = 0.99). The determined activation energy exceeds 5.88 kJ mol-1, affirming the prevalence of physisorption as the dominant mechanism in the adsorption process. Thermodynamic analysis confirmed that the adsorption process is endothermic (ΔH) and occurs spontaneously (ΔG), indicating a random (ΔS) nature. However, the percentage removal plunged considerably after five consecutive adsorption-desorption cycles, attributed to the alterations of active sites on bGO and brGO.

Efficient removal of sparfloxacin antibiotic from water using sulfonated graphene oxide: Kinetics, thermodynamics, and environmental implications

Pharmaceutical contamination poses a significant threat to global health. Due to their high solubility in water, antibiotics are difficult to remove. This study produced and used sulfonated graphene oxide (SGO) to adsorb sparfloxacin from aquatic environments. UV-Visible, Fourier transform infrared (FTIR), X-ray diffraction (XRD), XPS, SEM, TEM, EDX, particle size, Thermogravimetric analysis (TGA), and acid-base titration were used to characterize synthesized SGO particles. The BET technique determined SGO's surface area (32.25 m2/g). The calculated pHPZC of SGO was 2.5. Sparfloxacin adsorption onto SGO was analyzed using adsorption duration, medium pH, adsorbent dosages, antibiotic concentration, cations, and solution temperature. The pseudo-second-order kinetic model better described experimental kinetic data than the pseudo-first-order and Elovich models. Equilibrium isotherm data supported the Langmuir model, revealing a peak absorption capacity of 1428.57 μmol/g at 25 °C. The kinetic and isotherm models' applicability was assessed using error analysis. A thermodynamic analysis revealed an endothermic, spontaneous adsorption process with a change in entropy (ΔS) of 114.15 J/mol K and enthalpy (ΔH) of 8.44 kJ/mol. A regeneration analysis showed that SGO adsorption efficiency topped 86.4 % after five cycles.

Recent Progress on the Adsorption of Heavy Metal Ions Pb(II) and Cu(II) from Wastewater

With the processes of industrialization and urbanization, heavy metal ion pollution has become a thorny problem in water systems. Among the various technologies developed for the removal of heavy metal ions, the adsorption method is widely studied by researchers and various nanomaterials with good adsorption performances have been prepared during the past decades. In this paper, a variety of novel nanomaterials with excellent adsorption performances for Pb(II) and Cu(II) reported in recent years are reviewed, such as carbon-based materials, clay mineral materials, zero-valent iron and their derivatives, MOFs, nanocomposites, etc. The novel nanomaterials with extremely high adsorption capacity, selectivity and particular nanostructures are summarized and introduced, along with their advantages and disadvantages. And, some future research priorities for the treatment of wastewater are also prospected.

Sensing lead ions in water: a comprehensive review on strategies and sensor materials

It is well-known fact that elevated lead ions (Pb2+), the third most toxic among heavy metal ions in aqueous systems, pose a threat to human health and aquatic ecosystems when they exceed permissible limits. Pb2+ is commonly found in industrial waste and fertilizers, contaminating water sources and subsequently entering the human body, causing various adverse health conditions. Unlike being expelled, Pb2+ accumulates within the body, posing potential health risks. The harmful impact of presence of Pb2+ in water have prompted researchers to diligently work toward maintaining water quality. Recognizing the importance of Pb2+, this review article makes a sincere and effective effort to address the issues associated with Pb2+. This overview article gives insights into various sensing approaches to detect Pb2+ in water using different sensing materials, including 2-dimensional materials, thiols, quantum dots, and polymers. Herein, different sensing approaches such as electrochemical, optical, field effect transistor-based, micro-electromechanical system-based, and chemi resistive are thoroughly explained. Field effect transistor-based and chemiresistive work on similar principles and are compared on the basis of their fabrication processes and sensing capabilities. In conclusion, future directions for chemiresistive sensors in Pb2+ detection are proposed, emphasizing their simplicity, portability, straightforward functionality, and ease of fabrication. Notably, it sheds light on various thiol and ligand compounds and coupling strategies utilized in Pb2+ detection. This comprehensive study is expected to benefit individuals engaged in Pb2+ detection.

Characterization and application of synthesized calcium alginate-graphene oxide for the removal of Cr3+, Cu2+ and Cd2+ ions from tannery effluents

Environmental sustainability has gained acceptance to achieving the goal of a secure ecosystem with a reliable management system. Heavy metal remediation of aqueous streams is of special concern due to the intractability and persistence in the environment. Adsorption is a potential alternative to the existing inefficient conventional technologies for the removal and recovery of metal ions from aqueous solutions and becomes vital to align with the Sustainable Development Goals (SDGs) and mitigate the adverse environmental and social impacts. Calcium Alginate-Graphene oxide (CA-GO) composite has been synthesized for the adsorption of heavy metals including Cr3+, Cu2+, and Cd2+ ions from tannery effluents. Graphene oxide is prepared from commercial graphite powder and reacted with sodium alginate and calcium chloride to form the beads of CA-GO composite. The developed composite was characterized by FTIR, elemental analysis, SEM, XRD analysis, and Raman spectroscopy. Moreover, the effect of pH, adsorbent dosage, contact time, and initial concentration of metal ions on the adsorption capacity were investigated through batch experiments. At a pH>3.0 (pHzpc), the carboxyl group of CA-GO was deprotonated to make the surface negatively charged and facilitate metal adsorption. The optimum pH and maximum adsorption capacity of CA-GO for removal of Cr(III), Cu(II), and Cd(II) were 4.5, 6.0, and 7.0, and 90.58, 108.57, and 134.77 mg g-1, respectively. The kinetics, adsorption isotherms, and thermodynamics were studied to determine the adsorption mechanism. The kinetic of adsorption adopted the second-order model. Thermodynamic parameter were calculated and the adsorption process was determined to be exothermic and spontaneous at room temperature. The developed composite has been efficaciously applied for the removal of metal ions and pollution from real tannery effluents.

Fabrication of Mesoporous Silica Nanoparticle-Decorated Graphene Oxide Sheets for the Effective Removal of Lead (Pb2+) from Water

Mesoporous silica nanoparticle-decorated graphene oxide nanosheets (MSiO2-GO) were synthesized and characterized for the active removal of lead (Pb2+) from the water. MSiO2 NPs were prepared via an ultrasonication method using tetraethyl orthosilicate (TEOS), and GO sheets were obtained via a modified Hummers' method. X-ray diffraction, UV-vis spectroscopy, Fourier transform infrared spectroscopy, and energy dispersive X-ray spectroscopy specified the composition of MSiO2 NPs and GO sheets. The surface charge and texture of the MSiO2-GO nanosheets were obtained using the ζ-potential technique and by field emission scanning electron microscopy. The relative cytotoxicity test of MSiO2 NPs and MSiO2-GO nanosheets was performed on Murine Raw 264.7 cells before implying the treatment of water. Adsorption of Pb2+ ions on MSiO2-GO nanosheets was examined at various parameters such as different aqueous pH values (2.0-10.0), MSiO2-GO nanosheet doses (3, 5, 10, 15, 20 mg L-1), time intervals (2-30 min), and temperatures (25-45 °C). About 90% of Pb2+ ions were removed from water within 30 min (MSiO2-GO dose: 15 mg L-1; initial Pb2+ ions: 50 mg L-1; temperature: 25 °C; shaking speed: 200 rpm). The maximal uptake of Pb2+ was obtained at solution pH 6.0. Pseudo-first- and pseudo-second-order kinetic rate equations describe the sorption dynamic data. Pb2+ sorption isotherms were modeled using the Freundlich and Langmuir isotherm models. The possible mechanism of binding of Pb2+ ions onto MSiO2-GO nanosheets has been discussed. The exhausted MSiO2-GO nanosheets were successfully regenerated using 0.005 M HNO3 as the desorbing agent.

Highly Efficient Capture of Heavy Metal Ions on Amine-Functionalized Porous Polymer Gels

Porous polymer gels (PPGs) are characterized by inherent porosity, a predictable structure, and tunable functionality, which makes them promising for the heavy metal ion trap in environmental remediation. However, their real-world application is obstructed by the balance between performance and economy in material preparation. Development of an efficient and cost-effective approach to produce PPGs with task-specific functionality remains a significant challenge. Here, a two-step strategy to fabricate amine-enriched PPGs, NUT-21-TETA (NUT means Nanjing Tech University, TETA indicates triethylenetetramine), is reported for the first time. The NUT-21-TETA was synthesized through a simple nucleophilic substitution using two readily available and low-cost monomers, mesitylene and α, α′-dichloro-p-xylene, followed by the successful post-synthetic amine functionalization. The obtained NUT-21-TETA demonstrates an extremely high Pb2+ capacity from aqueous solution. The maximum Pb2+ capacity, qm, assessed by the Langmuir model was as high as 1211 mg/g, which is much higher than most benchmark adsorbents including ZIF-8 (1120 mg/g), FGO (842 mg/g), 732-CR resin (397 mg/g), Zeolite 13X (541 mg/g), and AC (58 mg/g). The NUT-21-TETA can be regenerated easily and recycled five times without a noticeable decrease of adsorption capacity. The excellent Pb2+ uptake and perfect reusability, in combination with a low synthesis cost, gives the NUT-21-TETA a strong potential for heavy metal ion removal.

A Review on Graphene (GN) and Graphene Oxide (GO) Based Biodegradable Polymer Composites and Their Usage as Selective Adsorbents for Heavy Metals in Water

Water pollution due to heavy metal ions has become a persistent and increasing problem globally. To combat this, carbonaceous materials have been explored as possible adsorbents of these metal ions from solution. The problem with using these materials on their own is that their lifespan and, therefore, usability is reduced. Hence the need to mask them and an interest in using polymers to do so is picked. This introduces an improvement into other properties as well and opens the way for more applications. This work gives a detailed review of the major carbonaceous materials, graphene and graphene oxide, outlining their origin as well as morphological studies. It also outlines the findings on their effectiveness in removing heavy metal ions from water, as well as their water absorption properties. The section further reports on graphene/polymer and graphene oxide/polymer composites previously studied and their morphological as well as thermal properties. Then the work done in the absorption and adsorption capabilities of these composites is explored, thereby contrasting the two materials. This enables us to choose the optimal material for the desired outcome of advancing further in the utilization of carbonaceous material-based polymer composites to remove heavy metal ions from water.

On-Chip Electromembrane Surrounded Solid Phase Microextraction for Determination of Tricyclic Antidepressants from Biological Fluids Using Poly(3,4-ethylenedioxythiophene)-Graphene Oxide Nanocomposite as a Fiber Coating

In the present study, on-chip electromembrane surrounded solid phase microextraction (EM-SPME) was employed in the determination of tricyclic antidepressants (TCAs), including amitriptyline, nortriptyline, imipramine, desipramine, maprotiline, and sertraline, from various biological fluids. In this regard, poly(3,4-ethylenedioxythiophene)-graphene oxide (PEDOT-GO) was electrodeposited on an SPME fiber as a conductive coating, then the fiber played the acceptor-electrode role during the extraction. Thus, the immigration of the analytes under the influence of an electric field and their absorption onto the fiber coating were accomplished simultaneously. Under the optimized conditions, the limits of detection for the target analytes were acquired in the range of 0.005-0.025 µg L^-1 using gas chromatography-mass spectrometry. The linearity of the method was 0.010-500 µg L^-1 for the imipramine and sertraline, 0.025-500 µg L^-1 for the amitriptyline, nortriptyline, and desipramine, and 1.000-250 µg L^-1 for the maprotiline (R² ≥ 0.9984). Moreover, this method provided suitable precision and fiber-to-fiber reproducibility, with RSDs ≤ 8.4%. The applicability of the proposed setup was eventually investigated for extraction of the drugs from human bone marrow aspirate, urine, plasma, and well water samples, in which satisfactory relative recoveries, from 93-105%, were obtained.

Removal of Pb2+, CrT, and Hg2+ Ions from Aqueous Solutions Using Amino-Functionalized Magnetic Nanoparticles

In this paper, a circular economy approach with the adsorption and desorption of heavy metal (HM) ions—i.e., lead (Pb2+), chromium (CrT), and mercury (Hg2+)—from aqueous solutions was studied. Specific and selective binding of HM ions was performed on stabilized and amino-functionalized iron oxide magnetic nanoparticles (γ-Fe2O3@NH2 NPs) from an aqueous solution at pH 4 and 7. For this purpose, γ-Fe2O3@NH2 NPs were characterized by thermogravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), specific surface area (BET), transmission electron microscopy (TEM), EDXS, and zeta potential measurements (ζ). The effects of different adsorbent amounts (mads = 20/45/90 mg) and the type of anions (NO3−, Cl−, SO42−) on adsorption efficiency were also tested. The desorption was performed with 0.1 M HNO3. The results showed improvement of adsorption efficiency for CrT, Pb2+, and Hg2+ ions at pH 7 by 45 mg of g-Fe2O3@NH2 NPs, and the sequence was as follows: CrT > Hg2+ > Pb2+, with adsorption capacities of 90.4 mg/g, 85.6 mg/g, and 83.6 mg/g, respectively. The desorption results showed the possibility for the reuse of γ-Fe2O3@NH2 NPs with HNO3, as the desorption efficiency was 100% for Hg2+ ions, 96.7% for CrT, and 91.3% for Pb2+.

Preparation of Graphene Oxide-Maghemite-Chitosan Composites for the Adsorption of Europium Ions from Aqueous Solutions

The adsorption of Eu(III) on composites synthesised from graphene oxide (GO), maghemite (MGH), and chitosan (CS) has been studied using different approaches. The physicochemical and morphological characteristics of the composites GO-MGH, GO-CS, GO-MGH-CS I, II, and III were determined by XRD, Mössbauer spectroscopy, FTIR, Raman spectroscopy, and TEM. According to the results of batch experiments, the maximum experimental adsorption capacity was 52, 54, 25, 103, and 102 mg/g for GO-MGH, GO-CS, GO-MGH-CS I, II, and III, respectively. The data obtained are in better agreement with the Langmuir, pseudo-second-order, and pseudo-first-order models only for GO-MGH. Thus, the adsorption of Eu(III) on the composites was a favourable, monolayer, and occurred at homogeneous sites. The nature of adsorption is chemical and, in the case of GO-MGH, physical. Tests of the composites in natural waters showed a high removal efficiency for Eu(III), Pu(IV), and Am(III), ranging from 74 to 100%. The ANFIS model has quite good predictive ability, as shown by the values for R², MSE, SSE, and ARE. The GO-MGH-CS composites with the high adsorption capacity could be promising candidates for the removal of Eu(III) and the pre-concentration of Pu(IV) and Am(III) from natural waters.

Removal of toxic metals from wastewater environment by graphene-based composites: A review on isotherm and kinetic models, recent trends, challenges and future directions

Access to clean water has reduced in recent years due to pollution and man-made activities. Wastewater treatment regimens are many such as electrocoagulation, adsorption, ozonation, membrane and advanced oxidation processes. Owing to economical, resource availability and ease of operation adsorption has upper hand over all other methods employed in wastewater treatment. Graphene based adsorbents attracted researchers due to their ability to play dual role as adsorbent and photo-catalysts. When it comes to removal of heavy metals and dyes graphene-based aerogels are successful. Graphene composites were predominantly synthesized by top-down and bottom-up approach methods. Graphene composites are mesoporous and have microporous structure on surface. Graphene has copper desorption efficiency of 90 % upon 10th consecutive cycle. Graphene based adsorbents have adsorption efficiency of 367, 246 and 106.3 mg^-1 for lead, zinc and cadmium respectively. Though graphene possesses numerous applications, this review was devoted towards heavy metals removal from aqueous environment. In detail, the synthesis routes and interaction mechanism were explained and also the adsorption isotherms, kinetics were added. This review will serve as support for future research directions on removal of wastewater contaminants (heavy metals).

Selective removal of some heavy metals from Lanthanide solution by graphene oxide functionalized with sodium citrate

Lanthanides are widely used in several advanced technologies, and the presence of heavy metal ions as traces reduce their efficiencies. Hence, adsorption of some heavy metals from Lanthanides aqueous solution using previously prepared graphene oxide-citrate (GO-C) composite was reported. In this regard, the GO-C was applied to remove various heavy metal ions (Fe, Ni, Mn) through the batch technique. The GO-C after the adsorption process was characterized by various advanced techniques. The results obtained from the experimental investigations revealed that the GO-C showed a rapid equilibrium adsorption time (1.0 min) for all the studied heavy metal ions. Moreover, the adsorption isotherm data for Fe3+, Mn2+, and Ni2+ was fit by the Langmuir isotherm model with excellent adsorption capacity for Fe3+ (535.0 mg/g), Mn2+ (223.22 mg/g), and Ni2+ (174.65 mg/g). Furthermore, the GO-C can be reused over five times to enhance the removal efficiency. Interestingly, the GO-C adsorbent achieved removal performance reached 95.0% for the Fe3+ and ≥ 35.0% for Ni, Mn, Co, and Cu compared to < 1% for lanthanides metal ions.

GO-SWCNT Buckypapers as an Enhanced Technology for Water Decontamination from Lead

Water decontamination is an important challenge resulting from the incorrect disposal of heavy metal waste into the environment. Among the different available techniques (e.g., filtration, coagulation, precipitation, and ion-exchange), adsorption is considered the cheapest and most effective procedure for the removal of water pollutants. In the last years, several materials have been tested for the removal of heavy metals from water, including metal-organic frameworks (MOFs), single-walled carbon nanotubes (SWCNTs), and graphene oxide (GO). Nevertheless, their powder consistency, which makes the recovery and reuse after adsorption difficult, is the main drawback for these materials. More recently, SWCNT buckypapers (SWCNT BPs) have been proposed as self-standing porous membranes for filtration and adsorption processes. In this paper, the adsorption capacity and selectivity of Pb²⁺ (both from neat solutions and in the presence of other interferents) by SWCNT BPs were evaluated as a function of the increasing amount of GO used in their preparation (GO-SWCNT buckypapers). The highest adsorption capacity, 479 ± 25 mg g⁻¹, achieved for GO-SWCNT buckypapers with 75 wt.% of graphene oxide confirmed the effective application of such materials for cheap and fast water decontamination from lead.

Graphene Oxide/Polyvinyl Alcohol–Formaldehyde Composite Loaded by Pb Ions: Structure and Electrochemical Performance

An immobilization of graphene oxide (GO) into a matrix of polyvinyl formaldehyde (PVF) foam as an eco-friendly, low cost, superior, and easily recovered sorbent of Pb ions from an aqueous solution is described. The relationships between the structure and electrochemical properties of PVF/GO composite with implanted Pb ions are discussed for the first time. The number of alcohol groups decreased by 41% and 63% for PVF/GO and the PVF/GO/Pb composite, respectively, compared to pure PVF. This means that chemical bonds are formed between the Pb ions and the PVF/GO composite based on the OH groups. This bond formation causes an increase in the T_g values attributed to the formation of a strong surface complexation between adjacent layers of PVF/GO composite. The conductivity increases by about 2.8 orders of magnitude compared to the values of the PVF/GO/Pb composite compared to the PVF. This means the presence of Pb ions is the main factor for enhancing the conductivity where the conduction mechanism is changed from ionic for PVF to electronic conduction for PVF/GO and PVF/GO/Pb.

Nanostructured Materials for Water Purification: Adsorption of Heavy Metal Ions and Organic Dyes

Chemical water pollution poses a threat to human beings and ecological systems. The purification of water to remove toxic organic and inorganic pollutants is essential for a safe society and a clean environment. Adsorption-based water treatment is considered one of the most effective and economic technologies designed to remove toxic substances. In this article, we review the recent progress in the field of nanostructured materials used for water purification, particularly those used for the adsorption of heavy metal ions and organic dyes. This review includes a range of nanostructured materials such as metal-based nanoparticles, polymer-based nanomaterials, carbon nanomaterials, bio-mass materials, and other types of nanostructured materials. Finally, the current challenges in the fields of adsorption of toxic materials using nanostructured materials are briefly discussed.

Simple and low-cost production of magnetite/graphene nanocomposites for heavy metal ions adsorption

It is challenging to produce economical magnetic graphene-based adsorbents on an industrial scale for heavy metal ions removal. Here, magnetite/graphene nanocomposite embedded in activated carbon matrix (magnetite/G-AC) was synthesized via in situ catalytic graphitization of iron-impregnated biochar to obtain graphene encapsulated iron nanoparticles (GEINs) embedded in biochar (BC) matrix, and followed by steam activation of GEINs-BC. Steam activation aimed to upgrade biochar to activated carbon with oxygen functional groups, crack encapsulated graphene shell to graphene nanosheets, and obtain magnetic Fe₃O₄ by oxidation of iron, thereby improving the adsorption capacity of magnetite/G-AC-800 (153.2 mg/g) four times higher than that of GEINs-BC. The parameters on the adsorption capacity were investigated using Pb(II) ions as a typical pollutant as a function of solution pH (3-7), contact time (5-300 min), initial Pb(II) concentration (50-400 mg/L), and adsorbent dosage (0.05-0.25 g). The fitted pseudo-second-order kinetic model and Langmuir model indicated that the main adsorption mechanism was chemical adsorption over monolayer. This research developed a low-cost magnetic adsorbent with the advantage of simple large-scale production and excellent adsorption capacity per unit cost for remediating wastewater.

Potential of hypercrosslinked microporous polymer based on carbazole networks for Pb(II) ions removal from aqueous solutions

In this research, porous adsorbents of hypercrosslinked microporous polymer based on carbazole networks (HCP-CN) were synthesized for Pb(II) elimination from wastewaters. The results demonstrated that the extreme HCP-CN adsorbents utilization in wastewater treatment could remove more than 99.88% of Pb (II) ions. Furthermore, the two consumed adsorbents similarly indicated rapid adsorption kinetics, and it merely took a while to achieve adsorption equilibrium. These characteristics showed that HCP-CN adsorbent was an outstanding candidate for Pb(II) elimination from wastewater. Besides, the thermodynamic characteristics involving Gibbs free energy change (∆G⁰), entropy change (∆S⁰), and enthalpy change (∆H⁰) of the adsorption procedure were evaluated, and the results affirmed that the adsorption process was exothermic and spontaneous. In addition, response surface methodology (RSM) as a statistical investigation was used to optimize adsorption factors to obtain maximum adsorption capacity and investigate the interactive effect of parameters using central composite design (CCD). Optimum conditions obtained by RSM for maximum adsorption capacity of 26.02 mg/g are 35 °C, 40 mg/L, 11, 60 min, and 99.88 for temperature, initial concentration, pH, time, and removal percent, respectively. In the kinetic modeling study, the second-order model was selected as the best model. The values R² at temperatures 35 °C, 40 °C, and 55 °C are 0.997, 0.9997, and 0.998, respectively. In the isotherm modeling, Hill model with a value R² of 0.9766 has a superior precision compared to the other isotherm models. Also, the values of ΔH and ΔS at Pb(II) concentration of 60 mg/L are 122.622 kJ/mol and 0.463 kJ/mole K, respectively.

Synthesis and Applications of Graphene Oxide

Thanks to the unique properties of graphite oxides and graphene oxide (GO), this material has become one of the most promising materials that are widely studied. Graphene oxide is not only a precursor for the synthesis of thermally or chemically reduced graphene: researchers revealed a huge amount of unique optical, electronic, and chemical properties of graphene oxide for many different applications. In this review, we focus on the structure and characterization of GO, graphene derivatives prepared from GO and GO applications. We describe GO utilization in environmental applications, medical and biological applications, freestanding membranes, and various composite systems.

Novel Chemoresistive Sensor for Sensitive Detection of Pb2+ Ions Using an Interdigital Gold Electrode Fabricated with a Reduced Graphene Oxide-Based Ion-Imprinted Polymer

This study presents novel chemoresistive reduced graphene oxide-ion-imprinted polymer (IIP-rGO)-based sensors for detection of lead (Pb2+) ions. The ion-imprinted polymer was synthesized by bulk polymerization and modified with a variable amount of rGO incorporated to form an IIP-rGO composite. The amount of rGO in the polymer matrix affected the sensor's relative response, and 1:3 mass ratio produced excellent results, with a consistent trend as the concentration of Pb2+ ions increased in the solution. The decrease in relative resistance (ΔR/R o) followed an exponential decay relationship between the ΔR/R o response and the concentration of Pb2+ ions in aqueous solutions. After solving the exponential decay function, it is observed that the sensor has the upper limit of ΔR/R o >1.7287 μg L-1, and the limit of detection of the sensor is 1.77 μg L-1. A nonimprinted polymer (NIP)-based sensor responded with a low relative resistance of the same magnitude although the concentration was varied. The response ratio of the IIP-based sensor to the NIP-based sensor (ΔR/R o)IIP/(ΔR/R o)NIP as a function of the concentration of Pb2+ ions in the solution shows that the response ratios recorded a maximum of around 22 at 50 μg L-1 and then decreased as the concentration increased, following an exponential decay function with the minimum ratio of 2.09 at 200 μg L-1 but never read 1. The sensor showed excellent selectivity against the bivalent cations Mn2+, Fe2+, Sn2+, and Ti2+. The sensor was capable of exhibiting 90% ΔR/R o response repeatability in a consecutive test.

3D Graphene Oxide Hydrogel Derived from Waste Toner as Adsorbent

Waste toner powders are considered as hazardous materials to human and living things, and should be properly recycled by many effective ways due to their fine particle sizes and complex components. In this paper, waste toner powders were used as raw materials to successfully synthesize three dimensions (3D) graphene oxide (GO) hydrogel by means of a one-pot chemical transformation based on the improved Hummers' method. The obtained 3D GO hydrogel has porous structure and abundant oxygen-containing functional groups because of the inherent 3D solid structure of waste toner powder and the strong oxidation process of the improved Hummers' method. Interestingly, the as-prepared 3D GO hydrogel with excellent adsorptive property could quickly remove Pb(II) ions (100 mg/L, removal efficiency of 96% and removal capacity of 144 mg/g) and methylene blue (50 mg/L, removal efficiency of 97% and removal capacity of 48 mg/g) from water, respectively. The preparation process of 3D GO hydrogel was simple and easy to operate, and the output can be moderately mass produced, thus it would provide a new and effective disposal way for the recycling and reusing of waste toner.

Graphene oxide and its nanocomposites with EDTA or chitosan induce apoptosis in MCF-7 human breast cancer

To achieve the advanced anticancer activity of nanocomposites fabricated with graphene oxide (GO), a novel procedure was used during the fabrication of chitosan (CS) or ethylene diamine tetra acetic acid (EDTA). The synthesized GO-based nanocomposites were distinguished through different analytical techniques. The cytotoxic activity was examined using MTT assays against three different cancer cell lines. Cell cycle distribution and apoptosis were studied by flow cytometry. Caspase-8, caspase-9, and VEGFR-2 levels were determined using the ELISA technique. HRTEM results revealed a regular 2D thin sheet with a transparent surface in non-modified GO and for GO-CS, the surface of GO has clear cuts and lines had developed due to CS insertion. Concerning the MCF-7 breast cancer cell line, the lowest IC50 values were recorded, suggesting the most powerful cytotoxic effect on breast cancer cells. Treatment with GO-EDTA resulted in the lowest IC50 value of 3.8 ± 0.18 μg mL-1. As indicated by the annexin V-FITC apoptosis assay, the total apoptosis highest percentage was in GO-EDTA treatment (30.12%). In addition, the study of cell cycle analysis showed that GO-EDTA arrested the cell cycle primarily in the G0/G1 phase (33.74%). CS- and EDTA-conjugated GO showed an anti-cancer activity through their cytotoxic effect against the MCF-7 breast cancer cell line.

A Review of Adsorbents for Heavy Metal Decontamination: Growing Approach to Wastewater Treatment

Heavy metal is released from many industries into water. Before the industrial wastewater is discharged, the contamination level should be reduced to meet the recommended level as prescribed by the local laws of a country. They may be poisonous or cancerous in origin. Their presence does not only damage people, but also animals and vegetation because of their mobility, toxicity, and non-biodegradability into aquatic ecosystems. The review comprehensively discusses the progress made by various adsorbents such as natural materials, synthetic, agricultural, biopolymers, and commercial for extraction of the metal ions such as Ni2+, Cu2+, Pb2+, Cd2+, As2+ and Zn2+ along with their adsorption mechanisms. The adsorption isotherm indicates the relation between the amount adsorbed by the adsorbent and the concentration. The Freundlich isotherm explains the effective physical adsorption of the solute particle from the solution on the adsorbent and Langmuir isotherm gives an idea about the effect of various factors on the adsorption process. The adsorption kinetics data provide valuable insights into the reaction pathways, the mechanism of the sorption reaction, and solute uptake. The pseudo-first-order and pseudo-second-order models were applied to describe the sorption kinetics. The presented information can be used for the development of bio-based water treatment strategies.

Highly efficient and selectivity removal of heavy metal ions using single-layer NaxKyMnO2 nanosheet: A combination of experimental and theoretical study

Manganese oxides (MnO₂) are widely applied in heavy metal ions removal due to their low-cost, environmental-friendly and biocompatibility. However, the adsorption capacity of MnO₂ need to be further improved to satisfy the demand of practical application. Herein, a highly dispersed single layer Na_xK_yMnO₂ nanosheet was synthesized by a facile wet-chemical method with sodium dodecyl sulfonate as surfactant. The high surface specific area, excellent dispersibility and abundant oxygen vacancies endowed Na_xK_yMnO₂ nanosheets with potential in heavy metal ions adsorption. The adsorption experiments results showed that Na_xK_yMnO₂ nanosheets possessed high efficiency and selectivity towards lead ion (Pb²⁺) with a high adsorption capacity of 2091.8 μmol g^-1. The Na_xK_yMnO₂ also showed an excellent reusability with the removal rate of 95.4% for Pb²⁺ even after five cycles. Moreover, both the theoretical calculation and experimental data illustrated that the single layer Na_xK_yMnO₂ nanosheets possess high selectivity to Pb²⁺ adsorption.

Fabrication of RHA-silica/graphene oxide nanocomposites for removal of lead ions from water

In this study, rice husk ash-silica/graphene oxide (RHA-SiO₂/GO) nanocomposites were synthesized by the in situ method using (3-aminopropyl) triethoxysilane as a coupling agent. The obtained products were used to remove lead ions (Pb²⁺) from aqueous solution. Effects of SiO₂:GO mass ratio, contact time, pH and initial Pb²⁺ concentration on the adsorption capacity were studied. It was found that the suitable ratio of SiO₂:GO for Pb²⁺ adsorption is 100:2. The suitable RHA-SiO₂/GO was characterized by Fourier-transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, Brunauer-Emmett-Teller specific surface area and thermal gravimetric analysis. Accordingly, RHA-SiO₂/GO nanocomposite could be used as promising adsorbent for the removal of Pb²⁺ from water.

Synthesis of Manganese Ferrite/Graphene Oxide Magnetic Nanocomposite for Pollutants Removal from Water

These days, environmental pollution, notably water pollution, has increasingly caused severe human health problems. The major water pollutants are heavy metals. MnFe2O4/GO nanocomposite was prepared in the current work via in situ method and tested to remove lead ion Pb2+ and neutral red (NR) dye from water. The prepared nanocomposite was characterized using different techniques, including X-ray diffraction, transmission electron microscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray photoelectron spectroscopy, Raman spectra, and vibrating sample magnetometer. The prepared nanocomposite showed high adsorption capacity toward Pb2+ and NR dye removal according to Langmuir fitting indicating the monolayer homogeneous adsorption of pollutants over the adsorbent surface and can be separated easily with an external magnet. The effect of different factors, including contact time, pH, initial concentration, and adsorbent dose on the adsorption, were also studied. The increased concentration of pollutants led to increased adsorption capacity from 63 to 625 mg/g for Pb2+ ions and from 20 to 90 mg/g for NR dye. The increased adsorbent dose led to increased removal efficiency from 39% to 98.8% and from 63% to 94% for Pb2+ and NR dye, respectively. The optimum pH for the adsorption of both pollutants was found to be 6.0. The reusability of MnFe2O4/GO nanocomposite was studied for up to five cycles. The nanocomposite can keep its efficiency even after the studied cycles. So, the prepared magnetic nanocomposite is a promising material for water treatment.

A Multifactorial Approach to Untangle Graphene Oxide (GO) Nanosheets Effects on Plants: Plant Growth-Promoting Bacteria Inoculation, Bacterial Survival, and Drought

Drought is a limiting factor for agricultural productivity. Climate change threatens to expand the areas of the globe subjected to drought, as well as to increase the severity and duration of water shortage. Plant growth-promoting bacteria (PGPB) are widely studied and applied as biostimulants to increase plant production and to enhance tolerance to abiotic and biotic constraints. Besides PGPB, studies on the potential of nanoparticles to be used as biostimulants are also thriving. However, many studies report toxicity of tested nanoparticles in bacteria and plants in laboratory conditions, but few studies have reported effects of nanoparticles towards bacterial cells and communities in the soil. The combined application of nanoparticles and PGPB as biostimulant formulations are poorly explored and it is important to unravel the potentialities of their combined application as a way to potentiate food production. In this study, Rhizobium sp. E20-8 and graphene oxide (GO) nanosheets were applied on container-grown maize seedlings in watered and drought conditions. Bacterial survival, seedling growth (dry weight), and biochemical endpoints (photosynthetic pigments, soluble and insoluble carbohydrates, proline, lipid peroxidation, protein, electron transport system, and superoxide dismutase) were evaluated. Results showed that the simultaneous exposure to GO and Rhizobium sp. E20-8 was able to alleviate the stress induced by drought on maize seedlings through osmotic and antioxidant protection by GO and mitigation of GO effects on the plant’s biochemistry by Rhizobium sp. E20-8. These results constitute a new lead on the development of biostimulant formulations to improve plant performance and increase food production in water-limited conditions.

The cross-talk between lateral sheet dimensions of pristine graphene oxide nanoparticles and Ni2+ adsorption

This study investigated the removal of nickel(ii) ions by using two sizes of graphene oxide nanoparticles (GO - 450 nm and GO - 200 nm). The thickness and lateral sheet dimensions of GO are considered to be an important adsorbent and promising method for sufficient removal of metals like nickel, lead, copper, etc. The graphite oxide was prepared by oxidation-reduction reaction (Hummers method), and the final product was labelled as GO - 450 nm. A tip sonicator was used to reduce the size of particles to 200 nm under controlled conditions (time and power of sonication). FTIR spectroscopy shows that both sizes of GO particles contain several types of oxygen groups distributed onto the surface of GO particles. Scanning electron microscopy (SEM) and the statistical analysis confirmed the formation of these two sizes of GO particles. The GO - 200 nm performed better removal of Ni(ii) compared with GO - 450 nm, due to more surfaces being available. The adsorption capacity of GO particles increased drastically from 45 mg g-1 to 75 mg g-1 for GO - 450 nm and GO - 200 nm respectively, these values were carried out after 2 h of incubation. The kinetics of adsorption and several parameters like initial concentration at equilibrium, pH, temperature, and adsorbent dose are controlled and studied by using UV-visible spectroscopy. The results indicated a significant potential of GO - 200 nm as an adsorbent for Ni(ii) ion removal. An additional experiment was performed to estimate the surface area of GO - 450 nm and GO - 200 nm, the results show that the surface areas of GO - 450 nm and GO - 200 nm are 747.8 m2 g-1 and 1052.2 m2 g-1 respectively.

Facile synthesis of 2Dα-MnO2nanosheets for the removal of heavy metal ions

Removal of heavy metal ions (HMIs) has attracted great attentions due to the fact that they have serious effect on environment and human beings. Manganese oxide (MnO₂) was widely used as absorbent for the HMIs removal on account of its low-cost, eco-friendly and biocompatibility. The modification of morphological and structure is recognized as the effective route to improve the adsorption capacity. In this work, 2Dα-MnO₂nanosheets were synthesized by hydrothermal method with Al³⁺additive. With the merits of high specific surface area, high dispersity in aqueous solution and abundant surface defects, 2Dα-MnO₂nanosheets exhibited excellent HMIs adsorption performance. The maximum adsorption capacity of 2Dα-MnO₂nanosheets reached 1.604 mmol g^-1(Pb²⁺) and 0.813 mmol g^-1(Cd²⁺), respectively and can maintain stable after five cycles. Besides, the established adsorption kinetics fitted well with pseudo-second-order adsorption kinetics model. Based on the above results, 2Dα-MnO₂is efficient for the removal of HMIs and possesses remarkable practical application potential.

Evaluation of Thin Film Microextraction for trace elemental analysis of liquid samples using LIBS detection

An analytical methodology based in the combination of Thin Film Microextraction with Laser-induced Breakdown Spectroscopy (TFME-LIBS) was investigated, for the first time, for detection of Cu, Cr, Ni and Pb in aqueous solutions. In this methodology, the analytes were extracted in a thin film of adsorbent material deposited on a solid support, which was introduced in the sample to analyse. After extraction, the analytes retained in the adsorbent were analysed by LIBS. In order to obtain adsorbent films useful for the microextraction step, two different experimental procedures for film generation, denoted as Drop Casting Deposition and Mould Deposition, were evaluated. In both cases, graphene oxide was used as adsorbent material. The mould deposition procedure was found to produce more homogeneous graphene oxide layers, leading to more uniform distribution of the adsorbed analytes on the graphene oxide surface. Experimental parameters affecting the TFME procedure, such as the adsorbent amount and extraction time, were studied. Under optimum microextraction conditions, the analytical figures of merit of the proposed TFME-LIBS method were evaluated, leading to limits of detection ranging from 41 μg kg^-1 and 52 μg kg^-1. Method trueness, evaluated from the analysis of a real sample of bottle water, led to recovery values about 70%, indicating the existence of strong matrix effects probably due to the presence of major cations in the bottle water. After 50% dilution of the sample with deionized water, recoveries values improved to 100%-108%.

A review on MXene-based nanomaterials as adsorbents in aqueous solution

Environmental pollution has intensified and accelerated due to a steady increase in the number of industries, and finding methods to remove hazardous contaminants, which can be typically divided into inorganic and organic compounds, have become inevitable. One of the widely used water treatment technologies is adsorption and various kinds of adsorbents for the removal of inorganic and organic contaminants from water have been discovered. Recently, MXene, as an emerging nanomaterial, has gained rapid attention owing to its unique characteristics and various applicability. Particularly, in the area of adsorptive application, MXene and MXene-based adsorbents have shown great potential in a large number of studies. In this regard, a comprehensive understanding of the adsorptive behavior of MXene-based nanomaterials is necessary in order to explain how they remove inorganic and organic contaminants in water. Adsorption by MXene-based adsorbents tends to be highly influenced by not only the physicochemical properties of these adsorbents but also water quality, such as pH value, temperature, background ion, and natural organic matter. Therefore, in this review paper, the effect of various water quality on the adsorption of inorganic and organic contaminants by various types of MXene and MXene-based adsorbents is explored. Furthermore, this review also covers general trends in the synthesis of MXene and regeneration of MXene-based adsorbents in order to assess their stability.

Facile synthesis of graphene oxide from graphite rods of recycled batteries by solution plasma exfoliation for removing Pb from water

We herein present a simple, fast, efficient and environmentally friendly technique to prepare graphene oxide (GO) from graphite rods of recycled batteries by using solution plasma exfoliated techniques at atmospheric pressure. The prepared GO with an average 3 nm-thickness and 1.5 μm-length, having large surface area and high porosity, has been used to remove Pb(ii) ions from the water. The obtained results indicated that the adsorption of Pb(ii) onto GO depends on pH, contact time, temperature and initial concentration of Pb(ii). The maximum adsorption capacity of Pb(ii) onto GO determined from the Langmuir model (with a high R² value of 0.9913) was 180.1 mg g⁻¹ at room temperature. A removal efficiency of ∼96.6% was obtained after 40 min. Calculations of thermodynamic parameters (ΔG°, ΔH° và ΔS°) show the adsorption of Pb(ii) ions on the GO surface is spontaneous and intrinsically heat-absorbing. The potential mechanism can be suggested here to be the interaction of the π–π* bonding electrons and Pb(ii) as well as the electrostatic attraction between Pb(ii) and the oxygen-containing functional groups on GO.

Facile synthesis of graphene oxide from graphite rods of recycled batteries by solution plasma exfoliation for removing Pb from water.

Effects of foliar application of graphene oxide on cadmium uptake by lettuce

Although graphene oxide (GO) has been widely used to enhance soil quality and crop yield, there is currently little information regarding the effects of foliar application of GO on cadmium (Cd) toxicity to plants. In this study, we investigated the response to GO in lettuce cultivated under Cd stress in hydroponic conditions. Lettuce was grown from seeds in a nutrient solution supplemented with 2 mg/L Cd and the leaves were sprayed with 0, 30, and 60 mg/L GO. The results indicated that application of 30 mg/L GO significantly increased the total length, surface area, average diameter, and hair number of lettuce roots, and effectively alleviated the negative effects of Cd on root growth. Furthermore, foliar application of 30 mg/L GO, but not 60 mg/L GO, significantly improved the quality of lettuce, including reduction in Cd accumulation in leaves and roots and increase in soluble sugar, protein, and vitamin C content. Transmission electron microscopy revealed that GO nanoparticles, which entered the leaves and were subsequently transported to the roots via the vascular system (phloem), reduced the damaging effect of Cd on cellular organelles, including the cell wall and membrane, chloroplasts, and starch granules. The effect may be attributed to the absorption of GO by lettuce cells, where it fixed Cd2+, thus reducing Cd2+ bioavailability, or to the improvement of Cd tolerance through regulation of lettuce metabolic pathways. Gaussian simulation analysis revealed that Cd caused significant changes in the GO molecule, resulting in detachment of an epoxy group from the GO carbon ring and breakage of OH bonds in hydroxyl groups, whereupon the oxygen freed from the OH bond formed a new bond with Cd. Collectively, these results indicate that foliar application of 30 mg/L GO can enhance the tolerance of lettuce to Cd, promote plant growth, and improve nutritional quality.

DFT study of the influence of impurities on the structural, electronic, optoelectronic, and nonlinear optical properties of graphene nanosheet functionalized by the carboxyl group -COOH

In this work, we propose a modified model of graphene oxide nanosheet (GON), based on the Lerf-Klinowski model, through which we attach a carboxyl group (GON-COOH) to the non-equivalent C atom of coronene-based graphene oxide with formation of sp3-like orbital bond. Beryllium, boron, nitrogen, oxygen, and fluorine atoms are integrated into the GON at identical sites in order to study their impact on the physical and chemical properties of GON. Our aim is to propose new efficient materials for applications in optoelectronics and nonlinear optics (NLO). Chemical reactivity and structural, optical, and nonlinear optical properties of GON and its derivatives GON-X (X: Be, B, N, O, and F atoms) were investigated by using the density functional theory (DFT) at the B3LYP-D3/6-31+G(d,p) level of theory. According to the results obtained, the binding energy per atom of GON compound decreases slightly with addition of atoms of the second period elements of the periodic table. The GON-F compound exhibits the smallest value of gap energy compared to other studied compounds and can then be considered a proficient candidate for photovoltaic applications. In regard to NLO properties, we found that the studied models of GON compound theoretically exhibit a larger value of the first static hyperpolarizability than urea, the reference compound for NLO properties.

Graphene oxide/polydimethylsiloxane composite sponge for removing Pb(ii) from water

An efficient adsorbent to remove Pb(ii) from water was prepared by treating polydimethylsiloxane (PDMS) sponge with polyvinyl alcohol and then coating the sponge with graphene oxide (GO). The GO-PDMS sponge was highly hydrophilic, easily handled during and after use, and easily recycled. The kinetics and isotherms of Pb(ii) sorption onto the GO-PDMS sponge were investigated by performing batch sorption tests. The kinetics of Pb(ii) sorption onto the GO-PDMS sponge indicated that sorption equilibrium occurred rapidly (within 60 min) and that the sorption data could be described using a pseudo-second-order model. Maximum Pb(ii) sorption onto the GO-PDMS sponge occurred at pH > 5. Increasing GO loading on the PDMS sponge increased the amount of Pb(ii) that could be sorbed. The isotherm for Pb(ii) sorption onto the GO-PDMS sponge was non-linear and was well described by the Langmuir isotherm model, indicating that Pb(ii) sorption onto the GO-PDMS sponge was homogeneous and occurred through sorption of a monolayer of Pb(ii). The GO-PDMS sponge, used as a filter, removed Pb(ii) efficiently from water. The Pb(ii) removal efficiencies were more than 50% and the maximum was 85%.

Instantaneous integration of magnetite nanoparticles on graphene oxide assisted by ultrasound for efficient heavy metal ion retrieval

We fabricated a magnetite nanoparticle-graphene oxide (GO) hybrid via a non-chemical and one-step process assisted by ultrasound in an aqueous solution where the nanoparticle attached to the hydrophobic region on graphite oxide (multi-layered GO) which, at the same time, was exfoliated. Unlike chemical methods such as precipitation, oxygen-containing functional groups on GO have not been consumed or reduced during the hybridization, leading that this hybrid exhibited good water solubility and high adsorption capacity for heavy metal ions such as Pb(II) and Au(III). After the adsorption, the hybrid was instantly collected using a magnet. This method can be useful for hybridizing various nanoparticles with GO.