Superior and efficient performance of cost-effective MIP-202 catalyst over UiO-66-(CO2H)2 in epoxide ring opening reactions

This study explored the catalytic performance of two robust zirconium-based metal-organic frameworks (MOFs), MIP-202(Zr) and UiO-66-(CO2H)2 in the ring-opening of epoxides using alcohols and amines as nucleophilic reagents. The MOFs were characterized by techniques such as FT-IR, PXRD, FE-SEM, and EDX. Through systematic optimization of key parameters (catalyst amount, time, temperature, solvent), MIP-202(Zr) achieved 99% styrene oxide conversion in 25 min with methanol at room temperature using 5 mg catalyst. In contrast, UiO-66-(CO2H)2 required drastically harsher conditions of 120 min, 60 °C, and four times the catalyst loading to reach 98% conversion. A similar trend was observed for ring-opening with aniline -MIP-202(Zr) gave 93% conversion in one hour at room temperature, while UiO-66-(CO2H)2 needed two hours at 60 °C for 95% conversion. The superior performance of MIP-202(Zr) likely stems from cooperative Brønsted/Lewis acid sites and higher proton conductivity enabling more efficient epoxide activation. Remarkably, MIP-202(Zr) maintained consistent activity over five recycles in the ring-opening of styrene oxide by methanol and over three recycles in the ring-opening of styrene oxide by aniline. Testing various epoxide substrates and nucleophiles revealed trends in reactivity governed by electronic and steric effects. The results provide useful insights into tuning Zr-MOF-based catalysts and highlight the promise of the cost-effective and sustainable MIP-202(Zr) for diverse epoxide ring-opening reactions on an industrial scale.

Tailoring parameters for QM/MM simulations: accurate modeling of adsorption and catalysis in zirconium-based metal-organic frameworks

Quantum mechanics/molecular mechanics (QM/MM) simulations offer an efficient way to model reactions occurring in complex environments. This study introduces a specialized set of charge and Lennard-Jones parameters tailored for electrostatically embedded QM/MM calculations, aiming to accurately model both adsorption processes and catalytic reactions in zirconium-based metal-organic frameworks (Zr-MOFs). To validate our approach, we compare adsorption energies derived from QM/MM simulations against experimental results and Monte Carlo simulation outcomes. The developed parameters showcase the ability of QM/MM simulations to represent long-range electrostatic and van der Waals interactions faithfully. This capability is evidenced by the prediction of adsorption energies with a low root mean square error of 1.1 kcal mol-1 across a wide range of adsorbates. The practical applicability of our QM/MM model is further illustrated through the study of glucose isomerization and epimerization reactions catalyzed by two structurally distinct Zr-MOF catalysts, UiO-66 and MOF-808. Our QM/MM calculations closely align with experimental activation energies. Importantly, the parameter set introduced here is compatible with the widely used universal force field (UFF). Moreover, we thoroughly explore how the size of the cluster model and the choice of density functional theory (DFT) methodologies influence the simulation outcomes. This work provides an accurate and computationally efficient framework for modeling complex catalytic reactions within Zr-MOFs, contributing valuable insights into their mechanistic behaviors and facilitating further advancements in this dynamic area of research.

Nanoscale and chiral metal-organic frameworks for asymmetric reactions in water: bridging Lewis acid catalysis and biological systems

Nowadays, stereoselective control over the sheer variety of chemical transformations benefits from the multipotency of chiral Lewis acids. Their use under biocompatible conditions has long posed a challenge because profuse amounts of biogenic nucleophiles readily deactivate them. To bridge the gap between chiral Lewis acid catalysis and biocompatible chemistry, the conversion of UiO(BPY)-type nanosized metal-organic frameworks (NMOFs) into chiral variants was herein exemplified. The combination of an elongated 2,2'-bipyridyl linker and scandium salt with a hydrophobic anion proved essential to implement traits such as robustness, biocompatibility, and catalytic activity. The catalyst could construct sufficiently hydrophobic environments sequestered within the framework, catalyzing asymmetric ring-opening reactions of meso-epoxide with low catalyst loading to afford β-amino acid alcohols in high yield (up to >99%) with high enantioselectivity (up to 88%). Most impressively, it exhibited a tolerance to the ex vivo poisoning of chiral Lewis acid catalysis by biogenic nucleophiles in sharp contrast to conventional water-compatible Lewis acids.

Defect-enabling zirconium-based metal-organic frameworks for energy and environmental remediation applications

This comprehensive review explores the diverse applications of defective zirconium-based metal-organic frameworks (Zr-MOFs) in energy and environmental remediation. Zr-MOFs have gained significant attention due to their unique properties, and deliberate introduction of defects further enhances their functionality. The review encompasses several areas where defective Zr-MOFs exhibit promise, including environmental remediation, detoxification of chemical warfare agents, photocatalytic energy conversions, and electrochemical applications. Defects play a pivotal role by creating open sites within the framework, facilitating effective adsorption and remediation of pollutants. They also contribute to the catalytic activity of Zr-MOFs, enabling efficient energy conversion processes such as hydrogen production and CO2 reduction. The review underscores the importance of defect manipulation, including control over their distribution and type, to optimize the performance of Zr-MOFs. Through tailored defect engineering and precise selection of functional groups, researchers can enhance the selectivity and efficiency of Zr-MOFs for specific applications. Additionally, pore size manipulation influences the adsorption capacity and transport properties of Zr-MOFs, further expanding their potential in environmental remediation and energy conversion. Defective Zr-MOFs exhibit remarkable stability and synthetic versatility, making them suitable for diverse environmental conditions and allowing for the introduction of missing linkers, cluster defects, or post-synthetic modifications to precisely tailor their properties. Overall, this review highlights the promising prospects of defective Zr-MOFs in addressing energy and environmental challenges, positioning them as versatile tools for sustainable solutions and paving the way for advancements in various sectors toward a cleaner and more sustainable future.

Nanomaterials-modified reverse osmosis membranes: a comprehensive review

Because of its great efficiency and widespread application, reverse osmosis (RO) is a popular tool for water desalination and purification. However, traditional RO membranes have a short lifespan due to membrane fouling, deterioration, decreased salt rejection rate, and the low water flux with aging. As a result, membrane modification has received a lot of attention recently, with nanomaterials being extensively researched to improve membrane efficacy and lifespan. Herein, we present an in-depth analysis of recent advances of RO membranes modification utilizing nanomaterials. An overview of the various nanomaterials used for membrane modification, including metal oxides, zeolites, and carbon nanomaterials, is provided. The synthesis techniques and methods of integrating these nanomaterials into RO membranes are also discussed. The impacts of nanomaterial change on the performance of RO membranes are addressed. The underlying mechanisms responsible for RO membrane enhancements by nanomaterials, such as improved surface hydrophilicity, reduced membrane fouling via surface repulsion and anti-adhesion properties, and enhanced structural stability, are discussed. Furthermore, the review provides a critical analysis of the challenges and limitations associated with the use of nanomaterials to modify RO membranes. Overall, this review provides valuable insights into the modification of RO membranes with nanomaterials, providing a full grasp of the benefits, challenges, and future prospects of this challenging topic.

Engineering Porosity and Functionality in a Robust Twofold Interpenetrated Bismuth-Based MOF: Toward a Porous, Stable, and Photoactive Material

Defect engineering in metal-organic frameworks (MOFs) has gained worldwide research traction, as it offers tools to tune the properties of MOFs. Herein, we report a novel 2-fold interpenetrated Bi-based MOF made of a tritopic flexible organic linker, followed by missing-linker defect engineering. This procedure creates a gradually augmented micro- and mesoporosity in the parent (originally nonporous) network. The resulting MOFs can tolerate a remarkable extent of linker vacancy (with absence of up to 60% of linkers per Bi node) created by altering the crystal-growth rate as a function of synthesis temperature and duration. Owing to the enhanced porosity and availability of the uncoordinated Lewis acidic Bi sites, the defect-engineered MOFs manifested improved surface areas, augmented CO2 and water vapor uptake, and catalytic activity. Parallel to this, the impact of defect engineering on the optoelectronic properties of these MOFs has also been studied, offering avenues for new applications.

Computational design of metal hydrides on a defective metal-organic framework HKUST-1 for ethylene dimerization

Catalytic ethylene dimerization to 1-butene is a crucial reaction in the chemical industry, as 1-butene is used for the production of most common plastics (e.g., polyethylene). With well-defined tuneable structures and unsaturated active sites, defective metal-organic frameworks have recently emerged as potential catalysts for ethylene dimerization. Herein, we computationally design a series of metal hydrides on defective HKUST-1 namely H-M-DHKUST-1 (M: Co, Ni, Cu, Ru, Rh and Pd), and subsequently assess their catalytic activity for ethylene dimerization by density functional theory calculations. Due to the antiferromagnetic behavior of dimeric metal-based clusters, we comprehensively investigate all possible multiplicity states on H-M-DHKUST-1 and observe multiplicity crossing. The ground-state reaction barriers for four elementary steps (initiation, C-C coupling, β-hydride elimination and 1-butene desorption) are rationalized and C-C coupling is revealed to be the rate-determining step on H-Co-, H-Ni-, H-Ru-, H-Rh- and H-Pd-DHKUST-1. The energy barrier for β-hydride elimination is found to be the lowest on H-Ru- and H-Rh-DHKUST-1, attributed to the weak stability of agostic arrangement; however, the energy barrier for 1-butene desorption is the highest on H-Rh-DHKUST-1. Among the designed H-M-DHKUST-1, Co- and Ni-based ones are predicted to exhibit the best overall catalytic performance. The mechanistic insights from this study may facilitate the development of new MOFs toward efficient ethylene dimerization and other industrially important reactions.

MOF-808 as an Efficient Catalyst for Valorization of Biodiesel Waste Production: Glycerol Acetalization

Glycerol is the main residue in the biodiesel production industry; therefore, their valorization is crucial. The acetalization of glycerol toward fuel additives such as solketal (2,2-dimethyl-1,3-dioxolan-4-methanol) is of high interest, promoting circular economy since it can be added to biodiesel or even fossil diesel to improve their quality and efficiency. Straightforward-prepared metal-organic framework (MOF) materials of the MOF-808 family were applied to the valorization of glycerol for the first time. In particular, MOF-808(Hf) was revealed to be an effective heterogeneous catalyst to produce solketal under moderate conditions: a small amount of the MOF material (only 4 wt% of glycerol), a 1:6 ratio of glycerol/acetone, and a temperature of 333 K. The high efficiency of MOF-808(Hf) was associated with the high amount of acid centers present in its structure. Furthermore, its structural characteristics, such as window opening cavity size and pore diameters, were shown to be ideal for reusing this material for at least ten consecutive reaction cycles without losing activity (conversion > 90% and selectivity > 98%). Remarkably, it was not necessary to wash or activate the MOF-808(Hf) catalyst between cycles (no pore blockage occurred), and it maintained structural integrity after ten cycles, confirming its ability to be a sustainable heterogeneous catalyst for glycerol valorization.

Synthetic control of correlated disorder in UiO-66 frameworks

Changing the perception of defects as imperfections in crystalline frameworks into correlated domains amenable to chemical control and targeted design might offer opportunities for the design of porous materials with superior performance or distinctive behavior in catalysis, separation, storage, or guest recognition. From a chemical standpoint, the establishment of synthetic protocols adapted to control the generation and growth of correlated disorder is crucial to consider defect engineering a practicable route towards adjusting framework function. By using UiO-66 as experimental platform, we systematically explored the framework chemical space of the corresponding defective materials. Periodic disorder arising from controlled generation and growth of missing cluster vacancies can be chemically controlled by the relative concentration of linker and modulator, which has been used to isolate a crystallographically pure "disordered" reo phase. Cs-corrected scanning transmission electron microscopy is used to proof the coexistence of correlated domains of missing linker and cluster vacancies, whose relative sizes are fixed by the linker concentration. The relative distribution of correlated disorder in the porosity and catalytic activity of the material reveals that, contrarily to the common belief, surpassing a certain defect concentration threshold can have a detrimental effect.

Ligand-Mediated Regulation of the Chemical/Thermal Stability and Catalytic Performance of Isostructural Cobalt(II) Coordination Polymers

Regulating the chemical/thermal stability and catalytic activity of coordination polymers (CPs) to achieve high catalytic performance is topical and challenging. The CPs are competent in promoting oxidative cross-coupling, yet they have not received substantial attention. Here, the ligand effect of the secondary ligand of CPs for oxidative cross-coupling reactions was investigated. Specifically, four new isostructural CPs [Co(Fbtx)1.5(4-R-1,2-BDC)]n (denoted as Co-CP-R, Fbtx = 1,4-bis(1,2,4-triazole-1-ylmethyl)-2,3,5,6-tetrafluorobenzene, 4-R-1,2-BDC = 4-R-1,2-benzenedicarboxylate, R = F, Cl, Br, CF3) were prepared. It was found that in the reactions of oxidative amination of benzoxazoles with secondary amines and the oxidative coupling of styrenes with benzaldehydes, both the chemical and thermal stabilities of the four Co-CPs with the R group followed the trend of -CF3 > -Br > -Cl > -F. Density functional theory (DFT) calculations suggested that the difference in reactivity may be ascribed to the effect of substituent groups on the electron transition energy of the cobalt(II) center of these Co-CPs. These findings highlight the secondary ligand effect in regulating the stability and catalytic performance of coordination networks.

Evaluation of the catalytic activity of Zn-MOF-74 for the alcoholysis of cyclohexene oxide

In the present work, nanocrystalline Zn-MOF-74 is shown to be a heterogeneous catalyst for the acid-catalyzed ring-opening alcoholysis of cyclohexene oxide. The results corroborated that accessible open metal sites within the material are critical conditions (Zn(ii) Lewis acid sites) for this reaction. Zn-MOF-74 was tested at three different temperatures (30, 40, and 50 °C) for the alcoholysis reaction. Furthermore, the cyclohexene oxide conversion was 94% in less than two days. A comparison of the catalytic activity with different crystal sizes of Zn-MOF-74 and the homogenous phase, zinc acetate, was conducted. Zn-MOF-74 exhibited excellent catalytic cyclability for three cycles without losing its activity. The material showed chemical stability by retaining its crystalline structure after the reaction and cyclability process.

Structure and Site Evolution of Framework Ni Species in MIL-127 MOFs for Propylene Oligomerization Catalysis

A mixed-valence oxotrimer metal-organic framework (MOF), Ni-MIL-127, with a fully coordinated nickel atom and two iron atoms in the inorganic node, generates a missing linker defect upon thermal treatment in helium (>473 K) to engender an open coordination site on nickel which catalyzes propylene oligomerization devoid of any cocatalysts or initiators. This catalyst is stable for ∼20 h on stream at 500 kPa and 473 K, unprecedented for this chemistry. The number of missing linkers on synthesized and activated Ni-MIL-127 MOFs is quantified using temperature-programmed oxidation, ¹H nuclear magnetic resonance spectroscopy, and X-ray absorption spectroscopy to be ∼0.7 missing linkers per nickel; thus, a majority of Ni species in the MOF framework catalyze propylene oligomerization. In situ NO titrations under reaction conditions enumerate ∼62% of the nickel atoms as catalytically relevant to validate the defect density upon thermal treatment. Propylene oligomerization rates on Ni-MIL-127 measured at steady state have activation energies of 55-67 kJ mol^-1 from 448 to 493 K and are first-order in propylene pressures from 5 to 550 kPa. Density functional theory calculations on cluster models of Ni-MIL-127 are employed to validate the plausibility of the missing linker defect and the Cossee-Arlman mechanism for propylene oligomerization through comparisons between apparent activation energies from steady-state kinetics and computation. This study illustrates how MOF precatalysts engender defective Ni species which exhibit reactivity and stability characteristics that are distinct and can be engineered to improve catalytic activity for olefin oligomerization.

Influence of 1-Butene Adsorption on the Dimerization Activity of Single Metal Cations on UiO-66 Nodes

Grafting metal cations to missing linker defect sites in zirconium-based metal-organic frameworks, such as UiO-66, produces a uniquely well-defined and homotopic catalytically active site. We present here the synthesis and characterization of a group of UiO-66-supported metal catalysts, M-UiO-66 (M = Ni, Co, Cu, and Cr), for the catalytic dimerization of alkenes. The hydrogen-deuterium exchange via deuterium oxide adsorption followed by infrared spectroscopy showed that the last molecular water ligand desorbs from the sites after evacuation at 300 °C leading to M(OH)-UiO-66 structures. Adsorption of 1-butene is studied using calorimetry and density functional theory techniques to characterize the interactions of the alkene with metal cation sites that are found active for alkene oligomerization. For the most active Ni-UiO-66, the removal of molecular water from the active site significantly increases the 1-butene adsorption enthalpy and almost doubles the catalytic activity for 1-butene dimerization in comparison to the presence of water ligands. Other M-UiO-66 (M = Co, Cu, and Cr) exhibit 1-3 orders of magnitude lower catalytic activities compared to Ni-UiO-66. The catalytic activities correlate linearly with the Gibbs free energy of 1-butene adsorption. Density functional theory calculations probing the Cossee-Arlman mechanism for all metals support the differences in activity, providing a molecular level understanding of the metal site as the active center for 1-butene dimerization.

Two Zn(II)/Cd(II) Coordination Polymers as Recyclable Heterogeneous Catalysts for an Efficient Room-Temperature Synthesis of α-Aminonitriles via the Solvent-Free Strecker Reaction

The α-aminonitriles are versatile building blocks in the synthesis of natural or artificial amino acids as well as important intermediates in organic synthesis. For their synthesis, the three-component Strecker reaction involving an aldehyde or a ketone together with amines and trimethylsilyl cyanide is used. In the literature, hydrothermally produced metal-based heterogeneous Lewis acid catalysts have been utilized in various solvents. In this work, we aimed at a greener approach toward such catalysis by (a) making two precatalysts with d¹⁰ metal centers, {[Zn(hipamifba)(H₂O)]·2H₂O}_n (1) and {[Cd(hipamifba)(H₂O)₂]·2H₂O}_n (2) (where H₂hipamifba = 4-(((4-((carboxymethyl) carbamoyl)phenyl)amino)methyl)benzoic acid), via an easy and scalable room-temperature method, and (b) showcasing the use of these coordination polymers (CPs) as very efficient, recyclable, and heterogeneous catalysts for the Strecker reaction to form α-aminonitriles in high yields under solvent-free reaction at ambient conditions. This has also allowed us to demonstrate the importance of open metal sites in such catalysis through an efficiency comparison between activated 1 and 2. In addition, activated 2 exhibited a wide substrate scope including a natural product Girgensohnine, providing an example of a natural product synthesis by a CP catalyst via an organic transformation such as the Strecker reaction.

The use of metal-organic frameworks as heterogeneous catalysts

This article presents an overview of some of the available research studies of MOFs as catalysts. Catalytic studies of magnetic iron oxide nanoparticles with modified surfaces, MOFs with precious metals such as palladium, platinum, and silver, with zirconium, hafnium, copper, alkaline earth metals, lanthanides are generalized. The studies of the catalytic activity of micro- and mesoporous MOF structures are described.

Multifunctional Catalysis by a One-Dimensional Copper(II) Metal Organic Framework Containing Pre-existing Coordinatively Unsaturated Sites: Intermolecular C-N, C-O, and C-S Cross-Coupling; Stereoselective Intramolecular C-N Coupling; and Aziridination Reactions

The coordinatively unsaturated sites (CUS) are vital in metal-centered catalysis. Metal-organic frameworks (MOFs) provide a unique opportunity to generate and stabilize CUS due to their robust structure. Generally, the generation of CUS in MOFs needs prior activation under heat and high vacuum to remove labile molecules occupying the catalytic sites. Herein, we report a solvothermal synthesis of a ready-to-use copper MOF containing accessible pre-existing CUS that does not need activation. The single crystal X-ray diffraction structure reveals a square planar Cu(II) center with two N-methylimidazoles (Mim) and one benzenedicarboxylic acid (BDC) with the formula unit [Cu^II(BDC)(Mim)₂]_n (Cu-1D) forming an infinite one-dimensional (1D) chain along the c axis. The 1D chains are stabilized by noncovalent π-π, CH···π, and H-bonding interaction to give 2D (sheet-like) and 3D networks in the solid state. The quantification of non-covalent interaction is studied by Hirshfeld surface analysis, and the formation of a higher architecture in the solid state is confirmed by SEM analysis. The reported Cu-1D MOF acts as a solid heterogeneous catalyst and exhibits efficient catalytic activity in intermolecular and intramolecular cross-coupling reactions. Intermolecular C-heteroatom cross-coupling of a variety of N-heterocycles, aliphatic, aromatic, alicyclic amines and amides (C-N), phenols (C-O), and thiols (C-S) with aryl halides (halide = I, Br) was achieved with 70 to 95% yield, better than the state-of-the-art Cu-based homogenous system. The C-N coupling catalytic cycle is initiated by the in situ reduction of Cu(II) by KOH/DMSO to Cu(I) species. Subsequently, Cu(I) undergoes oxidative addition followed by reductive elimination to form a cross-coupled product. High stereoselectivity was found for the intramolecular C-N coupling reaction to give tetrahydroquinoxalines with an enantiomeric excess (ee) of more than 99%. For a broader application, Cu-1D was applied as the catalyst for the synthesis of a library of aziridines that gives yields of up to 99% with more than 93% recyclability for each cycle.

Fabricating defect-rich metal-organic frameworks via mixed linker-induced crystal transformation

Defect-rich hcp UiO-66-NO₂ was synthesized via mixed linker-induced crystal transformation from fcu UiO-66-NO₂/NH₂. The defect concentration and porosity of hcp UiO-66-NO₂ can be fine-tuned by varying the BDC-NH₂/BDC-NO₂ ratio, which in turn endowed hcp UiO-66-NO₂ with superior catalytic performance in the ring-opening reaction of epoxides with alcohols.

Defect Engineering in Metal-Organic Framework Nanocrystals: Implications for Mechanical Properties and Performance

The growth process of metal-organic framework (MOF) nanocrystals defines their properties and functions. However, defects may be prevalent during the crystallization of even seemingly perfect MOFs, such as zeolitic imidazolate framework-8 (ZIF-8), and yet direct probing of such structural defects has been challenging because of the lack of nanoscale techniques to locally examine individual nanocrystals. Here, we directly study local defects, such as missing linkers or metal vacancies, in ZIF-8 nano- and microcrystals with near-field IR nanospectroscopy combined with density functional theory calculations. We track the chemical changes during crystallization and show that structural defects like zinc cations that are bound to molecules of the reactant gradually disappear with ripening of the crystals, while dangling and missing linker defects prevail. The resulting defect-terminating groups or open-metal sites produce mechanical anisotropy and reduce the Young's modulus, as measured via tip force microscopy with nanoscale resolution and supported by theoretical modeling. However, these structural defects also open the door for defect engineering to tune the performance of ZIF-8 by offering additional adsorption sites for targeted catalytic reactions, chemical sensing, or gas capture.

An efficient modulated synthesis of zirconium metal-organic framework UiO-66

The use of large amounts of deleterious solvents in the synthesis of metal-organic frameworks (MOFs) is one of the important factors limiting their application in industry. Herein, we present a detailed study of the synthesis of UiO-66, which was conducted with hydrobromic (HBr) acid as a modulator for the first time, at a high concentration of precursor solution (ZrCl4 and H2BDC, both 0.2 mol L-1). Powder crystals with atypical cuboctahedron structure were obtained which indicated that the HBr acid modulator played roles by competitive coordination and deprotonation modulation, thereby controlling the processes of nucleation and crystal growth. The properties of the obtained materials were systematically characterized and compared with those of materials synthesized with hydrofluoric (HF) acid and hydrochloric (HCl) acid modulators. Despite the high concentration of defectivity, the UiO-66 material synthesized with the HBr acid additive has the characteristics of larger specific surface area, excellent thermal stability and higher porosity in the structure. Besides that, the present protocol has the advantages of high reaction mass efficiency (RME), and feasibility of scalable synthesis, providing a facile and sustainable route to diverse Zr-based MOFs.

Bismuth gallate coordination networks inspired by an active pharmaceutical ingredient

The effect of solvent has been investigated for the synthesis of bismuth gallate compounds, of which the water-based bismuth subgallate has been used as an active pharmaceutical ingredient (API) for...

Strategies for induced defects in metal-organic frameworks for enhancing adsorption and catalytic performance

Metal-organic frameworks (MOFs) have emerged among porous materials. The designable structure and specific functionality make them stand out for diverse applications. In conceptual MOF, the metal ions/clusters and organic ligands...

Metal–organic framework (MOF)-, covalent-organic framework (COF)-, and porous-organic polymers (POP)-catalyzed selective C–H bond activation and functionalization reactions

The review summarizes the state-of-the-art of C–H active transformations over crystalline and amorphous porous materials as new emerging heterogeneous (photo)catalysts.

Creation of Exclusive Artificial Cluster Defects by Selective Metal Removal in the (Zn, Zr) Mixed-Metal UiO-66

The differentiation between missing linker defects and missing cluster defects in MOFs is difficult, thereby limiting the ability to correlate materials properties to a specific type of defects. Herein, we present a novel and easy synthesis strategy for the creation of solely "missing cluster defects" by preparing mixed-metal (Zn, Zr)-UiO-66 followed by a gentle acid wash to remove the Zn nodes. The resulting material has the reo UiO-66 structure, typical for well-defined missing cluster defects. The missing clusters are thoroughly characterized, including low-pressure Ar-sorption, iDPC-STEM at a low dose (1.5 pA), and XANES/EXAFS analysis. We show that the missing cluster UiO-66 has a negligible number of missing linkers. We show the performance of the missing cluster UiO-66 in CO₂ sorption and heterogeneous catalysis.

Generating Catalytic Sites in UiO-66 through Defect Engineering

UiO-66 is regarded as an epitome of metal-organic frameworks (MOFs) because of its stability. Defect engineering has been used as a toolbox to alter the performance of MOFs. UiO-66 is among the most widely explored MOFs because of its capability to bear a high number of defects without undergoing structural collapse. Several representative works in the field of MOF-based defect engineering are available based on UiO-66. In this review, more emphasis is given toward the construction of catalytic sites by engineering defects in UiO-66 as a representative including all the detailed synthesis procedures for inducing defects, and the characterization techniques used to analyze these defects in UiO-66 are discussed. Furthermore, a comprehensive review for the defects themselves and the support using defects in catalysis is provided to accentuate the importance of defect engineering.

Metal Organic Frameworks as Heterogeneous Catalysts in Olefin Epoxidation and Carbon Dioxide Cycloaddition

Metal–organic frameworks (MOFs) are a family of porous crystalline materials that serve in some cases as versatile platforms for catalysis. In this review, we overview the recent developments about the use of these species as heterogeneous catalysts in olefin epoxidation and carbon dioxide cycloaddition. We report the most important results obtained in this field relating them to the presence of specific organic linkers, metal nodes or clusters and mixed-metal species. Recent advances obtained with MOF nanocomposites were also described. Finally we compare the results and summarize the major insights in specific Tables, outlining the major challenges for this emerging field. This work could promote new research aimed at producing coordination polymers and MOFs able to catalyse a broader range of CO2 consuming reactions.

Abundant defects of zirconium-organic xerogels: High anhydrous proton conductivities over a wide temperature range and formic acid impedance sensing

There exists a challenge to develop solid-state proton conductors with high conductivity not only at high working temperatures (>353 K) but at start-up temperature and even at subzero temperature (<273 K) in cold climates or high-altitude drones. Here we present a series of zirconium-organic xerogels (Zr/Fum-xerogels) with porosity and defectivity, supported by N₂ sorption, thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS), exhibiting a high anhydrous proton conductivity over the temperature range of 233 to 433 K. The anhydrous conductivity of Zr/Fum-xerogel-0.04 reaches 5.68 × 10^-4 (233 K) and 2.5 × 10^-2 S cm^-1 (433 K), situating in the leading level of all anhydrous conductors reported to date. Further, the defective effects on acidities and conductive mechanisms of xerogels, especially structural changes of water clusters generated by varying temperatures are investigated by ion exchange capacity (IEC), X-ray photoelectron spectroscopy (XPS), temperature programmed desorption of NH₃ (NH₃-TPD) and in-situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). The zirconium-organic xerogels with outstanding conducting performance is further implemented as impedance sensor towards formic acid.

Distribution and diversity of dimetal-carboxylate halogenases in cyanobacteria

BACKGROUND

Halogenation is a recurring feature in natural products, especially those from marine organisms. The selectivity with which halogenating enzymes act on their substrates renders halogenases interesting targets for biocatalyst development. Recently, CylC - the first predicted dimetal-carboxylate halogenase to be characterized - was shown to regio- and stereoselectively install a chlorine atom onto an unactivated carbon center during cylindrocyclophane biosynthesis. Homologs of CylC are also found in other characterized cyanobacterial secondary metabolite biosynthetic gene clusters. Due to its novelty in biological catalysis, selectivity and ability to perform C-H activation, this halogenase class is of considerable fundamental and applied interest. The study of CylC-like enzymes will provide insights into substrate scope, mechanism and catalytic partners, and will also enable engineering these biocatalysts for similar or additional C-H activating functions. Still, little is known regarding the diversity and distribution of these enzymes.

RESULTS

In this study, we used both genome mining and PCR-based screening to explore the genetic diversity of CylC homologs and their distribution in bacteria. While we found non-cyanobacterial homologs of these enzymes to be rare, we identified a large number of genes encoding CylC-like enzymes in publicly available cyanobacterial genomes and in our in-house culture collection of cyanobacteria. Genes encoding CylC homologs are widely distributed throughout the cyanobacterial tree of life, within biosynthetic gene clusters of distinct architectures (combination of unique gene groups). These enzymes are found in a variety of biosynthetic contexts, which include fatty-acid activating enzymes, type I or type III polyketide synthases, dialkylresorcinol-generating enzymes, monooxygenases or Rieske proteins. Our study also reveals that dimetal-carboxylate halogenases are among the most abundant types of halogenating enzymes in the phylum Cyanobacteria.

CONCLUSIONS

Our data show that dimetal-carboxylate halogenases are widely distributed throughout the Cyanobacteria phylum and that BGCs encoding CylC homologs are diverse and mostly uncharacterized. This work will help guide the search for new halogenating biocatalysts and natural product scaffolds.

Controlling the molecular diffusion in MOFs with the acidity of monocarboxylate modulators

The catalytic performance of metal-organic frameworks (MOFs) is related to their physicochemical properties, such as particle size, defect chemistry and porosity, which can be potentially controlled by coordination modulation. By combining PXRD, ¹HNMR, FT-IR, and N₂ uptake measurements we have gained insights into the control of different types of defects (missing linker or missing cluster consequence of the spatial distribution of missing linkers, and a combination of both) by the type of modulator employed. We show that the molar percent of defects, either as missing linkers or as a part of missing cluster defects, is related to the acidity of a modulator and its subsequent incorporation into the UiO-66 structure. Modulators with strong acidity and small size result in a considerable defect induction that causes an increase in the external surface area and mesopore volume, which is beneficial for the ring-opening of epoxides with amines, using UiO-66 defect-modulated MOFs as heterogeneous catalysts.

The conversion of linoleic acid into hydroxytetrahydrofuran-structured bio-lubricant

In this work, a new structured linoleic-based hydroxytetrahydrofuran (HTHF) ester lubricant with excellent properties was developed. A synthesis route through regioselective enzymatic hydration was established, combining highly selective epoxidation with an intramolecular epoxide ring-opening reaction. The results proved that the enzymatic-chemical method is an alternative strategy for the conversion of linoleic acid into bio-lubricants. LiBr was revealed as an efficient catalyst (yields of 95.8%, and selectivity of 98.5%, respectively) for the intramolecular epoxide ring-opening reaction. The tribological properties test indicated that the HTHF bio-lubricants exhibited better performance than the commercial mineral oils. Physicochemical investigation further indicated that the product has a good thermal stability, with the T_onset around 300 °C. The kinematic viscosity and viscosity index indicated that the product is suitable to be applied for lubrication. In contrast with previous findings, this HTHF-structured bio-lubricant oil exhibited a superior low pour point (-64 °C) and provided great potential to be utilized in extreme cold working environments.

Tailoring Lewis/Brønsted acid properties of MOF nodes via hydrothermal and solvothermal synthesis: simple approach with exceptional catalytic implications

The Lewis/Brønsted catalytic properties of the Metal-Organic Framework (MOF) nodes can be tuned by simply controlling the solvent employed in the synthetic procedure. In this work, we demonstrate that Hf-MOF-808 can be prepared from a material with a higher amount of Brønsted acid sites, via modulated hydrothermal synthesis, to a material with a higher proportion of unsaturated Hf Lewis acid sites, via modulated solvothermal synthesis. The Lewis/Brønsted acid properties of the resultant metallic clusters have been studied by different characterization techniques, including XAS, FTIR and NMR spectroscopies, combined with a DFT study. The different nature of the Hf-MOF-808 materials allows their application as selective catalysts in different target reactions requiring Lewis, Brønsted or Lewis-Brønsted acid pairs.

A Computational Study of Isopropyl Alcohol Adsorption and Diffusion in UiO-66 Metal-Organic Framework: The Role of Missing Linker Defect

Defect engineering leads to an effective manipulation of the physical and chemical properties of metal-organic frameworks (MOFs). Taking the common missing linker defect as an example, the defective MOF generally possesses larger pores and a greater surface area/volume ratio, both of which favor an increased amount of adsorption. When it comes to the self-diffusion of adsorbates in MOFs, however, the missing linker is a double-edged sword: the unsaturated metal sites, due to missing linkers, could interact more strongly with adsorbates and result in a slower self-diffusion. Therefore, it is of fundamental importance to evaluate the two competing factors and reveal which one is dominating, a faster self-diffusion due to larger volume or a slower self-diffusion owing to strong interactions at unsaturated sites. In this work, via Monte Carlo and molecular dynamics simulations, we investigate the behavior of isopropyl alcohol (IPA) in the Zr-based UiO-66 MOFs, with a specific focus on the missing linker effects. The results reveal that unsaturated Zr sites bind strongly with IPA molecules, which in return would significantly reduce the self-diffusion coefficient of IPA. Besides this, for the same level of missing linkers, the location of defective sites also makes a difference. We expect such a theoretical study will provide an in-depth understanding of self-diffusion under confinement, inspire better defect engineering strategics, and promote MOF based materials toward challenging real-life applications.

The chemistry and applications of hafnium and cerium(iv) metal-organic frameworks

The coordination connection of organic linkers to the metal clusters leads to the formation of metal-organic frameworks (MOFs), where the metal clusters and ligands are spatially entangled in a periodic manner. The immense availability of tuneable ligands of different length and functionalities gives rise to robust molecular porosity ranging from several angstroms to nanometres. Among the large family of MOFs, hafnium (Hf) based MOFs have been demonstrated to be highly promising for practical applications due to their unique and outstanding characteristics such as chemical, thermal, and mechanical stability, and acidic nature. Since the report of UiO-66(Hf) and DUT-51(Hf) in 2012, less than 200 Hf-MOFs (ca. 50 types of structures) have been reported. Besides, tetravalent cerium [Ce(iv)] has been proven to be capable of forming similar topological MOF structures to Zr and Hf since its first discovery in 2015. So far, ca. 40 Ce(iv) MOFs with 60% having UiO-66-type structure have been reported. This review will offer a holistic summary of the chemistry, uniqueness, synthesis, and applications of Hf/Ce(iv)-MOFs with a focus on presenting the development in the Hf/Ce(iv)-clusters, topologies, ligand structures, synthetic strategies, and practical applications of Hf/Ce(iv)-MOFs. In the end, we will present the research outlook for the development of Hf/Ce(iv)-MOFs in the future, including fundamental design of Hf/Ce(iv)-clusters, defect engineering, and various applications including membrane development, diversified types of catalytic reactions, irradiation absorption in nuclear waste treatment, water production and wastewater treatment, etc. We will also present the emerging computational approaches coupled with machine-learning algorithms that can be applied in screening Hf and Ce(iv) based MOF structures and identifying the best-performing MOFs for tailor-made applications in future practice.

Water adsorption fingerprinting of structural defects/capping functions in Zr-fumarate MOFs: a hybrid computational-experimental approach

Engineering structural defects in MOFs has been intensively applied to modulate their adsorption-related properties. Zr-fumarate MOF (also known as MOF-801) is a prototypical defective MOF with proven versatile adsorption/separation performances depending on the synthetic conditions, however the relationship between the nature/concentration of both structure defects/capping functions and its adsorption features is still far from being fully understood. In this work, we first present a systematic theoretical exploration of the individual contributions of linker and cluster defects as well as of the capping functions to the overall water adsorption profile of the MOF-801 framework. This computational effort based on the construction of defective structure models and the use of Grand Canonical Monte Carlo simulations further enabled the identification of the overarching defective structure for two MOF-801 samples based on their experimental adsorption isotherms reported previously. An experimental effort was then deployed to synthesize two Zr-fumarate MOF samples with controlled nature and concentration of structural defects as well as capping functions. This computational-experimental hybrid strategy revealed the water adsorption isotherm as a fingerprint of the nature and concentration of structural defect/capping groups exhibited by the MOF adsorbent. We expect this study to deliver meaningful insights to further design MOFs with target adsorption features through a rational engineering of structural defects.

Cyclodextrins: a new and effective class of co-modulators for aqueous zirconium-MOF syntheses

Zr-MOFs exhibiting superior textural properties with BET surface area as high as 1451 m² g⁻¹ were successfully synthesized under hydrothermal conditions using native α-CD and β-CD as macromolecular additives.

An active and stable multifunctional catalyst with defective UiO-66 as a support for Pd over the continuous catalytic conversion of acetone and hydrogen

The one-pot synthesis of methyl isobutyl ketone (MIBK) and methyl isobutyl methanol (MIBC) from acetone and hydrogen is a typical cascade reaction comprised of aldol condensation-dehydration-hydrogenation. Pd loss and aggregation during long term operation are typical problems in industrial application. In this paper, an active and stable catalyst was achieved with defective UiO-66 as a support for Pd, which was synthesized with the ratio 15 : 1 of ZrOCl2·8H2O to ZrCl4 as Zr-precursors. The resultant Pd catalyst remained active for at least 1000 h with a MIBK + MIBC selectivity of 84.87-93.09% and acetone conversion of 45.26-53.22% in a continuous trickle-bed reactor. Besides the increased Brønsted acid amount generated by the defect sites was favorable for the activity, the cavity confinement in the UiO-66 (R = 15 : 1) structure also efficiently prevented Pd loss and aggregation during the long term run. The contrast of the characterization of the fresh and used Pd/UiO-66 (R = 15 : 1) indicated that the deactivation of the catalyst was attributed to carbonaceous accumulation on the catalyst surface, which could be easily regenerated by calcination. This work supplied a new alternative for the design and utilization of industrial catalysts for MIBK and MIBC synthesis.

Dialing in Catalytic Sites on Metal Organic Framework Nodes: MIL-53(Al) and MIL-68(Al) Probed with Methanol Dehydration Catalysis

Many metal organic frameworks (MOFs) incorporate metal oxide clusters as nodes. Node sites where linkers are missing can be catalytic sites. We now show how to dial in the number and occupancy of such sites in MIL-53 and MIL-68, which incorporate aluminum-oxide-like nodes. The methods involve modulators used in synthesis and postsynthesis reactions to control the modulator-derived groups on these sites. We illustrate the methods using formic acid as a modulator, giving formate ligands on the sites, and these can be removed to leave μ₂-OH groups and open Lewis acid sites. Methanol dehydration was used as a catalytic reaction to probe these sites, with infrared spectra giving evidence of methoxide ligands as reaction intermediates. Control of node surface chemistry opens the door for placement of a variety of ligands on a wide range of metal oxide cluster nodes for dialing in reactivity and catalytic properties of a potentially immense class of structurally well-defined materials.