Chemicals from lignin: an interplay of lignocellulose fractionation, depolymerisation, and upgrading

Selective regulation of products for guaiacol hydrodeoxygenation by adjusting type and acidity of supports

Upgrading lignin-oil into advanced fuels or chemicals has been widely studied in recent years. To understand the effect of support type and acidity on the hydrodeoxygenation (HDO) of guaiacol (lignin-oil model compound), Ni-based catalysts were prepared with SiO2, Al2O3 and ZSM-5 as supports, respectively. The catalysts were characterized by X-ray diffraction (XRD), N2 adsorption desorption, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and Pyridine adsorption Fourier-transform infrared (Py-IR). The research results indicate that selective regulation of guaiacol hydrogenation products can be achieved by changing the type and acidity of support. Cyclohexanol is the main product over Ni/SiO2, while cyclohexane is the main product over Ni/ZSM-5 series catalysts. Moreover, as the Si/Al ratio increases, the catalytic activity of Ni/ZSM-5 slightly decreases, and the yield of cyclohexane also decreases. The Brønsted acidity of the support is the key to promoting the conversion of cyclohexanol to cyclohexane. The formation of NiAl2O4 is the main reason for the relatively low activity of Ni/Al2O3. The conversion of guaiacol is as high as 99.2 %, and the yield of cyclohexane is as high as 86.6 % over Ni/ZSM-5(Si/Al = 27). In addition, complete conversion of guaiacol and 92.6 % yield of cyclohexanol were achieved over Ni/SiO2. More importantly, Ni/SiO2 and Ni/ZSM-5(27) are suitable for aromatic substrates with different substituents, respectively.

Catalytic depolymerization of Camellia oleifera shell lignin to phenolic monomers: Insights into the effects of solvent, catalyst and atmosphere

Camellia oleifera shell (COS) is a renewable biomass resource abundant in lignin with significant potential for producing phenolic monomers. However, the dearth of research has led to considerable resource wastage and environmental pollution. Herein, reductive catalytic fractionation (RCF) of COS was performed using noble metal catalysts in different solvents. An 11.1 wt% yield of phenolic monomers was achieved with 91% selectivity toward propylene-substituted monomers in H2O/EtOH (3:7, v/v) cosolvent under N2 atmosphere. Notably, the highest phenolic monomer yield of 17.0 wt% was obtained with impressive selectivity (86.9%) toward propanol-substituted monomers in the presence of H2. The GPC analysis and 2D HSQC NMR spectra indicated the effective depolymerization of lignin oligomers with catalysts. Phenolic monomers with ethyl, propyl, or propanol side chain could be produced from lignin-derived oligomers through hydrogenolysis, hydrogenation, and decarboxylation reactions. Overall, this study has paved the way for the valorization of COS lignin through the RCF strategy.

Membrane process and adsorption on pine nut shell for removal of dye from synthetic wastewater

Purification methods such as membrane technology and adsorption have been studied for the purification of textile effluents. This article aimed to evaluate the membrane separation process and adsorption on pine nut shell, separately and sequentially, for reactive dye blue 5G removal from a synthetic effluent. The membrane separation process was carried out in a front filtration module using polymeric membranes. The maximum dye retention was 35.9% using a regenerated cellulose membrane, with agitation and a pressure of 0.5 bar. The permeate flux was fully restored after cleaning the membrane. In the adsorption using pine nut shell, the best results were at pH 2, 50°C, and 50 ppm, with 85% dye removal. The Freundlich isotherm showed the best fit to the data, as did the pseudo-second-order kinetic model. The thermodynamic parameters indicated that the adsorption is of the physical type, with the process being endothermic and spontaneous. In the combined process, the permeate from the membrane separation process was subjected to adsorption on pine nut shell, achieving a removal rate of 98.7 for the initial concentration of 50 ppm. Therefore, this work shows the potential of pine nut shell as an adsorbent, not only to purify textile effluents but also to add value to a waste product, indicating that the combination of membrane technology and adsorption on pine nut shell could be an alternative for the treatment of textile effluents containing the reactive dye 5G blue.

Lignin hydrogenolysis: Tuning the reaction by lignin chemistry

Replacing fossil resource with biomass is one of the promising approaches to reduce our carbon footprint. Lignin is one of the three major components of lignocellulosic biomass, accounting for 10-35 wt% of dried weight of the biomass. Hydrogenolytic depolymerization of lignin is attracting increasing attention because of its capacity of utilizing lignin in its uncondensed form and compatibility with the biomass fractionation processes. Lignin is a natural aromatic polymer composed of a variety of monolignols associated with a series of lignin linkage motifs. Hydrogenolysis cleaves various ether bonds in lignin and releases phenolic monomers which can be further upgraded into valuable products, i.e., drugs, terephthalic acid, phenol. This review provides an overview of the state-of-the-art advances of the reagent (lignin), products (hydrol lignin), mass balance, and mechanism of the lignin hydrogenolysis reaction. The chemical structure of lignin is reviewed associated with the free radical coupling of monolignols and the chemical reactions of lignin upon isolation processes. The reactions of lignin linkages upon hydrogenolysis are discussed. The components of hydrol lignin and the selectivity production of phenolic monomers are reviewed. Future challenges on hydrogenolysis of lignin are proposed. This article provides an overview of lignin hydrogenolysis reaction which shows light on the generation of optimized lignin ready for hydrogenolytic depolymerization.

Accessing monomers from lignin through carbon-carbon bond cleavage

Lignin, the heterogeneous aromatic macromolecule found in the cell walls of vascular plants, is an abundant feedstock for the production of biochemicals and biofuels. Many valorization schemes rely on lignin depolymerization, with decades of research focused on accessing monomers through C-O bond cleavage, given the abundance of β-O-4 bonds in lignin and the large number of available C-O bond cleavage strategies. Monomer yields are, however, invariably lower than desired, owing to the presence of recalcitrant C-C bonds whose selective cleavage remains a major challenge in catalysis. In this Review, we highlight lignin C-C cleavage reactions, including those of linkages arising from biosynthesis (β-1, β-5, β-β and 5-5) and industrial processing (5-CH2-5 and α-5). We examine multiple approaches to C-C cleavage, including homogeneous and heterogeneous catalysis, photocatalysis and biocatalysis, to identify promising strategies for further research and provide guidelines for definitive measurements of lignin C-C bond cleavage.

Unlocking full potential of bamboo waster: Efficient co-production of xylooligosaccharides, lignin, and glucose through low-dosage mandelic acid hydrolysis with alkaline processing

Mandelic acid (MA), a natural and environmentally friendly organic acid, demonstrates high selectivity and efficiency in hydrolyzing hemicellulose, making it an excellent candidate for xylooligosaccharides (XOS) production at low acid dosages. Despite its potential, the application of MA for XOS production has not been evaluated. The study first investigated the effectiveness of MA in hydrolyzing hemicellulose in bamboo into XOS. Under optimized conditions (50 mM MA, 180 °C, 45 min), a high XOS yield of 65.9 % was achieved, with a total xylobiose and xylotriose yield of 43.5 %. Subsequent alkaline pretreatment enabled 92.1 % lignin removal from MA-pretreated bamboo. The recovered lignin exhibited a high purity of 95.2 % and retained fundamental structure and functional groups of native lignin. The resulting residue displayed enhanced crystallinity and accessibility, with reduced hydrophobicity and surface area lignin compared to untreated bamboo. At high substrate concentration of 20 %, cellulase hydrolysis resulted in a glucose conversion efficiency of 83.9 %. Overall, this integrated strategy offered an efficient approach for the co-production of valuable XOS, lignin, and glucose from bamboo. The efficient energy utilization and economic viability further highlight the potential of this method for large-scale industrial applications, making it an attractive option for biomass valorization.

Utilization of benzoic acid-based green deep eutectic solvents for the fractionation of lignocellulosic biomass

The fractionation of lignocellulose utilizing green solvents is essential for the effective operation of biorefineries. In this study, a deep eutectic solvent (DES) system composed of benzoic acid (BA, hydrogen bond donor) and choline chloride (ChCl, hydrogen bond acceptor) was fabricated and successfully applied to the lignocellulose fractionation. The DES has low toxicity and little pollution. In this system, 67.8 % of lignin and 91.2 % of hemicellulose in poplar were removed, leaving 95.8 % of cellulose intact as solid residue. Due to the removal of the amorphous components, crystallinity of cellulose-rich water-insoluble solid (CIS) substantially increased from 55.6 % to 68.6 %, and CIS was used as feedstock for nanocrystalline cellulose preparation with excellent properties. The results showed that the obtained lignin had similar properties to CEL by GPC, FT-IR, 2D-NMR and TGA. A high-purity lignin rich in G units was recovered with a well-preserved structure, which has β-O-4 linkage content up to 53.01 %, low molecular weight, low polydispersity (1.99). Finally, the hydrolyzate can be used for fermentation. This study demonstrated that BA is suitable for DES design with excellent properties on lignin extraction, and this promising DES enable efficient pretreatment for economically feasible biomass conversion. This ChCl-BA DES facilitates environmentally friendly production of functional materials derived from cellulose and lignin under mild conditions.

Mild and efficient approach to aromatic backbone cleavage using copper-lignosulfonate/hydrogen peroxide system

This study investigates the dual role of copper ions in catalysis and complexation during the oxidation of lignosulfonates with hydrogen peroxide (H2O2) under alkaline conditions. The presence of copper ions reduces partial oxidation by 86 % compared to H2O2 treatment alone, enhancing overall conversion efficiency to 63 % under increased oxidative conditions. Analyses reveal that copper-lignosulfonate complexes facilitate redox cycling and hydroxyl radical generation through interactions with H2O2, confirming copper's dual functions. This mechanism mitigates the hindrance of sulfonic groups on hydroperoxide anions, leading to lignosulfonate degradation into dicarboxylic acids. These findings provide novel insights into the copper-lignosulfonate/H2O2 system, expanding the understanding of oxidative degradation mechanisms beyond traditional Fenton-like reactions. Furthermore, this system offers a simplified and efficient alternative for industrial applications, particularly in integration with the sulfite pretreatment process of woody biomass for producing valuable co-products.

Valorization of Lactate Esters and Amides into Value-Added Biobased (Meth)acrylic Polymers

(Meth)acrylic polymers are massively produced due to their inherently attractive properties. However, the vast majority of these polymers are derived from fossil resources, which is not aligned with the tendency to reduce gas emissions. In this context, (meth)acrylic polymers derived from biomass (biobased polymers) are gaining momentum, as their application in different areas can not only stand the comparison but even surpass, in some cases, the performance of petroleum-derived ones. In this review, we highlight the design and synthesis of (meth)acrylic polymers derived from lactate esters (LEs) and lactate amides (LAs), both derived from lactic acid. While biobased polymers have been widely studied and reviewed, the poly(meth)acrylates with pendant LE and LA moieties evolved slowly until recently when significant achievements have been made. Hence, constraints and opportunities arising from previous research in this area are presented, focusing on the synthesis of well-defined polymers for the preparation of advanced materials.

Biological conversion of lignin-derived ferulic acid from wheat bran into vanillin

Lignin is a promising feedstock for producing vanillin, one of the most extensively used flavor enhancers. However, the biotransformation performance of lignin derivatives into vanillin is still unsatisfactory. In this study, an efficient conversion strategy of lignin into vanillin was established by employing engineered Saccharomyces cerevisiae as a whole-cell biocatalyst. Optimization of cell culture media and whole-cell bioconversion improved the production efficiency of vanillin. The vanillin titer reached 15.3 mM with a molar yield of 71 % in fed-batch fermentation mode, while incorporating in-situ product separation, demonstrated a remarkable 2.6-fold increase. The whole-cell bioconversion, coupled with in-situ separation, successfully converted real lignin hydrolysate into a record vanillin titer of 21.1 mM, equivalent to 1.8 mg of vanillin per gram of wheat bran biomass. The whole-cell bioconversion process integrated in-situ product separation, represents a sustainable approach for vanillin production and offers a promising pathway for lignin valorization.

Benzenoid Aromatics from Renewable Resources

In this Review, all known chemical methods for the conversion of renewable resources into benzenoid aromatics are summarized. The raw materials that were taken into consideration are CO2; lignocellulose and its constituents cellulose, hemicellulose, and lignin; carbohydrates, mostly glucose, fructose, and xylose; chitin; fats and oils; terpenes; and materials that are easily obtained via fermentation, such as biogas, bioethanol, acetone, and many more. There are roughly two directions. One much used method is catalytic fast pyrolysis carried out at high temperatures (between 300 and 700 °C depending on the raw material), which leads to the formation of biochar; gases, such as CO, CO2, H2, and CH4; and an oil which is a mixture of hydrocarbons, mostly aromatics. The carbon selectivities of this method can be reasonably high when defined small molecules such as methanol or hexane are used but are rather low when highly oxygenated compounds such as lignocellulose are used. The other direction is largely based on the multistep conversion of platform chemicals obtained from lignocellulose, cellulose, or sugars and a limited number of fats and terpenes. Much research has focused on furan compounds such as furfural, 5-hydroxymethylfurfural, and 5-chloromethylfurfural. The conversion of lignocellulose to xylene via 5-chloromethylfurfural and dimethylfuran has led to the construction of two large-scale plants, one of which has been operational since 2023.

Solid-State Structures and Properties of Lignin Hydrogenolysis Oil Compounds: Shedding a Unique Light on Lignin Valorization

This article explores the important, and yet often overlooked, solid-state structures of selected bioaromatic compounds commonly found in lignin hydrogenolysis oil, a renewable bio-oil that holds great promise to substitute fossil-based aromatic molecules in a wide range of chemical and material industrial applications. At first, single-crystal X-ray diffraction (SCXRD) was applied to the lignin model compounds, dihydroconiferyl alcohol, propyl guaiacol, and eugenol dimers, in order to elucidate the fundamental molecular interactions present in such small lignin-derived polyols. Then, considering the potential use of these lignin-derived molecules as building blocks for polymer applications, structural analysis was also performed for two chemically modified model compounds, i.e., the methylene-bridging propyl-guaiacol dimer and propyl guaiacol and eugenol glycidyl ethers, which can be used as precursors in phenolic and epoxy resins, respectively, thus providing additional information on how the molecular packing is altered following chemical modifications. In addition to the expected H-bonding interactions, other interactions such as π-π stacking and C-H∙∙∙π were observed. This resulted in unexpected trends in the tendencies towards the crystallization of lignin compounds. This was further explored with the aid of DSC analysis and CLP intermolecular energy calculations, where the relationship between the major interactions observed in all the SCXRD solid-state structures and their physico-chemical properties were evaluated alongside other non-crystallizable lignin model compounds. Beyond lignin model compounds, our findings could also provide important insights into the solid-state structure and the molecular organization of more complex lignin fragments, paving the way to the more efficient design of lignin-based materials with improved properties for industrial applications or improving downstream processing of lignin oils in biorefining processes, such as in enhancing the separation and isolation of specific bioaromatic compounds).

Benign and Selective Amination of Lignins towards Aromatic Biobased Building Blocks with Primary Amines

Lignin is a widely available second-generation biopolymer and the main potential source of renewable aromatic building blocks. Lignin-based polyamines offer great potential in applications based on chemical and materials sciences. However, common aminations techniques for lignin usually involve toxic chemicals and generate hindered and low reactivity amines. In this study, we developed two new, simple, and benign 2-step methodologies for the elaboration of lignin-based polyamines from different technical lignins (kraft, soda and organosolv) with a selectivity towards reactive primary amines. These methods involve grafting amide groups onto lignin followed by a hydrolysis step. Non-toxic heterocyclic compounds N-acetyl-2-oxazolidinone and 2-methyl-2-oxazoline were used as amidation agents. Hydrolysis was performed in acetone-water mixtures. Reactions were studied on model compounds and optimized on lignins. Aminated lignins were fully characterized and primary amines were quantified using quantitative 19F NMR. Our methods generated aminated lignins with low apparent molar masses and high solubility in water and solvents. Nitrogen contents of the products ranged between 2.0 and 3.5 mmol/g with reactive primary amines counts up to 1.7 mmol/g. These soluble and reactive lignin-based polyamines offer great potential as a replacement for fossil-based polyamines in e.g., the synthesis of aromatic polymer materials or as potential chelating, antibacterial agents.

Cu(II) Coordination Polymers for the Selective Oxidation of Biomass-Derived Veratryl Alcohol in Green Solvents: A Sustainable Catalytic Approach

Four air-stable one-dimensional copper(II) coordination polymers (CP1-CP4) with azide linkers were synthesized using tridentate NNS and NNN ligands. Single-crystal X-ray diffraction (XRD) analysis confirmed the molecular structures of CP1, CP3, and CP4. In the presence of TEMPO, all four coordination polymers demonstrated effective catalytic activity for the selective aerobic oxidation of veratryl alcohol, a biomass model compound, under base-free conditions. CP4 exhibited the best catalytic efficiency. Oxidations were conducted at ambient temperature (40 °C) utilizing air as a sustainable oxidant. Selective oxidation of veratryl alcohol to veratraldehyde was also conducted in the presence of a catalytic amount of base (5 mol %), and enhanced reactivity was observed. The green solvents, acetone, and water, were used to maximize sustainability. The optimized reaction conditions were applied to broaden the substrate scope of various lignin model alcohols and substituted benzylic alcohols with wide electronic variability. CP4 exhibited high recyclability, consistently providing quantitative yields even after ten consecutive runs. The catalytic protocol demonstrated sustainability and environmental compatibility, as evidenced by a low E-factor (4.29) and a high Eco-scale score (90). Based on experimental evidence and theoretical calculations, a plausible catalytic cycle was proposed. Finally, the sustainability credentials of the different optimized reaction protocols were evaluated using the CHEM21 green metrics toolkit.

Valorization of Lignocellulose with One-Step Acidified Monophasic Phenoxyethanol Fractionation

Effective fractionation of lignocelluosic biomass and subsequent valorization of all three major components under mild conditions were achieved. Pretreatment with acidified monophasic phenoxyethanol (EPH) efficiently removed 92.6 % lignin and 80 % xylan from poplar at 110 °C in 60 min, yielding high-value EPH-xyloside, EPH-modified lignin (EPHL), and a solid residue nearly purely composed of carbohydrates. After removing the grafted acetyl groups using 1 % NaOH at 50 °C, the highest enzymatic digestibility reached 92.3 %. EPHL could be recovered in high yield and purity with an uncondensed structure, while xylose was converted to EPH-xyloside, a potential precursor in biomedical industries. Additionally, the acidified monophasic EPH solvent could effectively fractionate biomass from species other than hardwood, achieving over 70 % delignification from recalcitrant pinewood under the same mild conditions, demonstrating the high potential of monophasic EPH pretreatment.

From sugars to aliphatic amines: as sweet as it sounds? Production and applications of bio-based aliphatic amines

Aliphatic amines encompass a diverse group of amines that include alkylamines, alkyl polyamines, alkanolamines and aliphatic heterocyclic amines. Their structural diversity and distinctive characteristics position them as indispensable components across multiple industrial domains, ranging from chemistry and technology to agriculture and medicine. Currently, the industrial production of aliphatic amines is facing pressing sustainability, health and safety issues which all arise due to the strong dependency on fossil feedstock. Interestingly, these issues can be fundamentally resolved by shifting toward biomass as the feedstock. In this regard, cellulose and hemicellulose, the carbohydrate fraction of lignocellulose, emerge as promising feedstock for the production of aliphatic amines as they are available in abundance, safe to use and their aliphatic backbone is susceptible to chemical transformations. Consequently, the academic interest in bio-based aliphatic amines via the catalytic reductive amination of (hemi)cellulose-derived substrates has systematically increased over the past years. From an industrial perspective, however, the production of bio-based aliphatic amines will only be the middle part of a larger, ideally circular, value chain. This value chain additionally includes, as the first part, the refinery of the biomass feedstock to suitable substrates and, as the final part, the implementation of these aliphatic amines in various applications. Each part of the bio-based aliphatic amine value chain will be covered in this Review. Applying a holistic perspective enables one to acknowledge the requirements and limitations of each part and to efficiently spot and potentially bridge knowledge gaps between the different parts.

Increased hydrophilicity of lignin-derivable vs. bisphenol-based polysulfones for potential water filtration applications

The functionality inherent in lignin-derivable aromatics (e.g., polar methoxy groups) can provide a potential opportunity to improve the hydrophilicity of polysulfones (PSfs) without the need for the additional processing steps and harsh reagents/conditions that are typically used in conventional PSf modifications. As determined herein, lignin-derivable PSfs without any post-polymerization modification exhibited higher hydrophilicity than comparable petroleum-based PSfs (commercial/laboratory-synthesized) and also demonstrated similar hydrophilicity to functionalized BPA-PSfs reported in the literature. Importantly, the lignin-derivable PSfs displayed improved thermal properties relative to functionalized BPA-PSfs in the literature, and the thermal properties of these bio-derivable PSfs were close to those of common non-functionalized PSfs. In particular, the glass transition temperature (T g) and degradation temperature of 5% weight loss (T d5%) of lignin-derivable PSfs (T g ∼165-170 °C, T d5% ∼400-425 °C) were significantly higher than those of typical functionalized BPA-PSfs in the literature (T g ∼110-160 °C, T d5% ∼240-260 °C) and close to those of unmodified, commercial/laboratory-synthesized BPA-/bisphenol F-PSfs (T g ∼180-185 °C, T d5% ∼420-510 °C).

Lignin self-assembly phenomena and valorization strategies for pulping, biorefining, and materials development: Part 1. The physical chemistry of lignin self-assembly

Physical chemistry aspects are emphasized in this comprehensive review of self-assembly phenomena involving lignin in various forms. Attention to this topic is justified by the very high availability, low cost, and renewable nature of lignin, together with opportunities to manufacture diverse products, for instance, polymers/resins, bioplastics, carbon fibers, bio-asphalt, sunscreen components, hydrophobic layers, and microcapsules. The colloidal lignin material, nanoparticles, and microstructures that can be formed as a result of changes in solvent properties, pH, or other adjustments to a suspending medium have been shown to depend on many factors. Such factors are examined in this work based on the concepts of self-assembly, which can be defined as an organizing principle dependent on specific attributes of the starting entities themselves. As a means to promote such concepts and to facilitate further development of nano-scale lignin products, this article draws upon evidence from a wide range of studies. These include investigations of many different plant sources of lignin, processes of delignification, solvent systems, anti-solvent systems or other means of achieving phase separation, and diverse means of achieving colloidal stability (if desired) of resulting self-assembled lignin structures. Knowledge of the self-organization behavior of lignin can provide significant structural information to optimize the use of lignin in value-added applications. Examples include chemical conditions and preparation procedures in which lignin-related compounds of particles organize themselves as spheres, hollow spheres, surface-bound layers, and a variety of other structures. Published articles show that such processes can be influenced by the selection of lignin type, pulping or extraction processes, functional groups such as phenolic, carboxyl, and sulfonate, chemical derivatization reactions, solvent applications, aqueous conditions, and physical processes, such as agitation. Precipitation from non-aqueous solutions represents a key focus of lignin self-assembly research. The review also considers stabilization mechanisms of self-assembled lignin-related structures.

Photoinduced Single Electron Reduction of the 4-O-5 Linkage in Lignin Models for C-P Coupling Catalyzed by Bifunctional N-Heterocyclic Carbenes

Catalytic activation of Caryl-O bonds is considered as a powerful strategy for the production of aromatics from lignin. However, due to the high reduction potentials of diaryl ether 4-O-5 linkage models, their single electron reduction remains a daunting challenge. This study presents the blue light-induced bifunctional N-heterocyclic carbene (NHC)-catalyzed one-electron reduction of diaryl ether 4-O-5 linkage models for the synthesis of trivalent phosphines. The H-bond between the newly devised bifunctional NHC and diaryl ethers is responsible for the success of the single electron transfer. Furthermore, this approach demonstrates selective one-electron reduction of unsymmetric diaryl ethers, oligomeric phenylene oxide, and lignin model.

Selective Cleavage of Cβ-O-4 Bond for Lignin Depolymerization via Paired-Electrolysis in an Undivided Cell

The cleavage of C-O bonds is one of the most promising strategies for lignin-to-chemicals conversion, which has attracted considerable attention in recent years. However, current catalytic system capable of selectively breaking C-O bonds in lignin often requires a precious metal catalyst and/or harsh conditions such as high-pressure H2 and elevated temperatures. Herein, we report a novel protocol of paired electrolysis to effectively cleave the Cβ-O-4 bond of lignin model compounds and real lignin at room temperature and ambient pressure. For the first time, "cathodic hydrogenolysis of Cβ-O-4 linkage" and "anodic C-H/N-H cross-coupling reaction" are paired in an undivided cell, thus the cleavage of C-O bonds and the synthesis of valuable triarylamine derivatives could be simultaneously achieved in an energy-effective manner. This protocol features mild reaction conditions, high atom economy, remarkable yield with excellent chemoselectivity, and feasibility for large-scale synthesis. Mechanistic studies indicate that indirect H* (chemical absorbed hydrogen) reduction instead of direct electron transfer might be the pathway for the cathodic hydrogenolysis of Cβ-O-4 linkage.

The Influence of the Comonomer Ratio and Reaction Temperature on the Mechanical, Thermal, and Morphological Properties of Lignin Oil-Sulfur Composites

Although lignin is a plentiful biomass resource, it continually exists as an underutilized component of biomass material. Elemental sulfur is another abundant yet underutilized commodity produced as a by-product resulting from the refining of fossil fuels. The current study presents a strategy for preparing five durable composites via a simple one-pot synthesis involving the reaction of lignin oil and elemental sulfur. These lignin oil-sulfur composites LOSx@T (where x = wt. % sulfur, ranging from 80 to 90, and T represents the reaction temperature in °C) were prepared via the reaction of elemental sulfur and lignin oil (LO) with elemental sulfur. The resulting composites could be remelted and reshaped several times without the loss of mechanical strength. Mechanical, thermal, and morphological studies showed that LOSx@T possesses properties competitive with some mechanical properties of commercial building materials, exhibiting favorable compressive strengths (22.1-35.9 MPa) and flexural strengths (5.7-6.5 MPa) exceeding the values required for many construction applications of ordinary Portland cement (OPC) and brick formulations. While varying the amount of organic material did not result in a notable difference in mechanical strength, increasing the reaction temperature from 230 to 300 °C resulted in a significant increase in compressive strength. The results reported herein reveal potential applications of both lignin and waste sulfur during the ongoing effort toward developing recyclable and sustainable building materials.

Advancement of lignin into bioactive compounds through selective organic synthesis methods

The conversion of lignin into bioactive compounds through selective organic synthesis methods represents a promising frontier in the pursuit of sustainable raw materials and green chemistry. This review explores the versatility of lignin-derived bioactive compounds, ranging from their application in drug discovery to their role in the development of biodegradable materials. Despite notable advancements, the synthesis routes and yields of highly bioactive molecules from lignin still require further exploration and improvement. This review provides an in-depth examination of the progress made in understanding the complex structure of lignin and developing innovative approaches to exploit its potential. Specifically, the types of lignins covered include softwood Kraft lignin, hardwood organosolv lignin, and soda lignin. This work is divided into three parts: first, the transformation of lignin into bioactive molecules with chemically active centres and functionalised hydroxyl groups through depolymerisation; second, kinetic modelling techniques essential for understanding the chemical kinetics of lignin and enabling significant scaling up in the conversion of organic molecules; third, efficient catalytic pathways for synthesising molecules with anticancer and antibacterial properties. In conclusion, this comprehensive review spurs further investigations into lignin-derived bioactive compounds, their applications, and the advancement of sustainable processes.

Perspective on Lignin Conversion Strategies That Enable Next Generation Biorefineries

The valorization of lignin, a currently underutilized component of lignocellulosic biomass, has attracted attention to promote a stable and circular bioeconomy. Successful approaches including thermochemical, biological, and catalytic lignin depolymerization have been demonstrated, enabling opportunities for lignino-refineries and lignocellulosic biorefineries. Although significant progress in lignin valorization has been made, this review describes unexplored opportunities in chemical and biological routes for lignin depolymerization and thereby contributes to economically and environmentally sustainable lignin-utilizing biorefineries. This review also highlights the integration of chemical and biological lignin depolymerization and identifies research gaps while also recommending future directions for scaling processes to establish a lignino-chemical industry.

Reducing Solvent Consumption in Reductive Catalytic Fractionation through Lignin Oil Recycling

Reductive catalytic fractionation (RCF) enables the simultaneous valorization of lignin and carbohydrates in lignocellulosic biomass through solvent-based lignin extraction, followed by depolymerization and catalytic stabilization of the extracted lignin. Process modeling has shown that the use of exogenous organic solvent in RCF is a challenge for economic and environmental feasibility, and previous works proposed that lignin oil, a mixture of lignin-derived monomers and oligomers produced by RCF, can be used as a cosolvent in RCF. Here, we further explore the potential of RCF solvent recycling with lignin oil, extending the feasible lignin oil concentration in the solvent to 100 wt %, relative to the previously demonstrated 0-19 wt % range. Solvents containing up to 80 wt % lignin oil exhibited 83-93% delignification, comparable to 83% delignification with a methanol-water mixture, and notably, using lignin oil solely as a solvent achieved 67% delignification in the absence of water. In additional experiments, applying the RCF solvent recycling approach to ten consecutive RCF reactions resulted in a final lignin oil concentration of 11 wt %, without detrimental impacts on lignin extraction, lignin oil molar mass distribution, aromatic monomer selectivity, and cellulose retention. Overall, this work further demonstrates the potential for using lignin oil as an effective cosolvent in RCF, which can reduce the burden on downstream solvent recovery.

Research Progress on Lignin Depolymerization Strategies: A Review

As the only natural source of aromatic biopolymers, lignin can be converted into value-added chemicals and biofuels, showing great potential in realizing the development of green chemistry. At present, lignin is predominantly used for combustion to generate energy, and the real value of lignin is difficult to maximize. Accordingly, the depolymerization of lignin is of great significance for its high-value utilization. This review discusses the latest progress in the field of lignin depolymerization, including catalytic conversion systems using various thermochemical, chemocatalytic, photocatalytic, electrocatalytic, and biological depolymerization methods, as well as the involved reaction mechanisms and obtained products of various protocols, focusing on green and efficient lignin depolymerization strategies. In addition, the challenges faced by lignin depolymerization are also expounded, putting forward possible directions of developing lignin depolymerization strategies in the future.

Aromatic Polymethacrylates from Lignin-Based Feedstock: Synthesis, Thermal Properties, Life-Cycle Assessment and Toxicity

There is currently a great need for rigid, high-performance and processable bio-based polymers and plastics as alternatives to the fossil-based materials used today. Here, we report on the straightforward synthesis and polymerization of lignin-derived methacrylate monomers based on the methyl esters of 4-hydroxybenzoic, vanillic, and syringic acid, respectively. The corresponding homopolymethacrylates exhibit high glass transition temperatures (Tgs) at 106, 128, and 197 °C, respectively. Rheological properties and thermal stability up to at least 277 °C indicate that these polymers are melt-processable. In addition, copolymers with methyl methacrylate are prepared to further vary and tune the polymer properties. An integrated ex-ante and prospective life-cycle assessment of key environmental impact parameters indicates similar or only slightly higher values compared to well-established fossil-based methyl methacrylate. Moreover, the toxicity towards human HeLa cell lines compares well with that of poly(methyl methacrylate). Hence, the potential availability of lignin-derived acids, combined with the straightforward and potentially upscalable monomer synthesis, make these rigid polymers appealing alternatives towards bio-based high-Tg thermoplastic materials with low toxicity.

Mechanocatalytic Hydrogenolysis of the Lignin Model Dimer Benzyl Phenyl Ether over Supported Palladium Catalysts

This work demonstrates the mechanocatalytic hydrogenolysis of the ether bond in the lignin model compound benzyl phenyl ether (BPE) and hardwood lignin isolated by hydrolysis with supercritical water. Pd catalysts with 4 wt % loading on Al2O3 and SiO2 supports achieve 100% conversion of BPE with a toluene production rate of (2.6-2.9) × 10-5 mol·min-1. The formation of palladium hydrides under H2 gas flow contributes to an increase in the turnover frequency by a factor of up to 300 compared to Ni on silica-alumina. While a near-quantitative toluene yield is obtained, some of the phenolic products remain adsorbed on the catalyst.

Sodium-Alginate-Doped Lignin Nanoparticles for PBAT Composite Films to Dually Enhance Tensile Strength and Elongation Performance with Functionality

It is a formidable challenge in thermoplastic/lignin composites to simultaneously boost tensile strength and elongation performance due to the rigidity of lignin. To address this issue, sodium-alginate-doped lignin nanoparticles (SLNPs) were prepared by combining solvent exchange and a coprecipitation method and used as an eco-friendly filler for poly(butylene adipate-co-terephthalate) (PBAT). The results indicated that the 1% polyanionic sodium alginate solution contributed to the formation of SLNP in lignin/THF solution. SLNP with a mean hydrodynamic diameter of ~500 nm and a Zeta potential value of -19.2 mV was obtained, indicating more hydrophobic lignin nanoparticles and a smaller number of agglomerates in SLNP suspension. Only 0.5 wt% SLNP addition improved the yield strength, tensile strength, and elongation at break by 32.4%, 31.8%, and 35.1% of the PBAT/SLNP composite films, respectively. The reinforcing effect resulted from the rigid aromatic structure of SLNP, whereas the enhanced elongation was attributed to the nanostructural feature of SLNP, which may promote boundary cracking. Additionally, the PBAT/SLNP composite films displayed excellent ultraviolet (UV) resistance with a UV shielding percentage near 100% for UVB and more than 75% for UVA, respectively. The addition of SLNP hindered water vapor, enhancing the moisture barrier properties. Overall, this study provides an effective strategy to eliminate the decrement in elongation performance for PBAT/lignin composites and suggest they are good candidates to be extensively utilized.

Valorization of lignin from aqueous-based lignocellulosic biorefineries

An additional 100 million tons/year of lignin coproduct will result when lignocellulosic biomass is processed in biorefineries to fiber, sugars, biofuels, and bioproducts. This will double the amount of lignin already generated from pulping and paper production. Unlike pulping that results in lignosulphonate (88% of total) or Kraft lignin (9%), aqueous-based biorefining leaves behind non-sulfonated lignin and aromatic molecules. This new type of lignin provides opportunities for large volume agricultural uses such as controlled-release carriers and soil amendments as well as feedstocks for new chemistries that lead to molecular building blocks for the chemical industry and to precursors for sustainable aviation biofuels.

Carbon Fiber Film with Multi-Hollow Channels to Expedite Oxygen Electrocatalytic Reaction Kinetics for Flexible Zn-Air Battery

The high oxygen electrocatalytic overpotential of flexible cathodes due to sluggish reaction kinetics result in low energy conversion efficiency of wearable zinc-air batteries (ZABs). Herein, lignin, as a 3D flexible carbon-rich macromolecule, is employed for partial replacement of polyacrylonitrile and constructing flexible freestanding air electrodes (FFAEs) with large amount of mesopores and multi-hollow channels via electrospinning combined with annealing strategy. The presence of lignin with disordered structure decreases the graphitization of carbon fibers, increases the structural defects, and optimizes the pore structure, facilitating the enhancement of electron-transfer kinetics. This unique structure effectively improves the accessibility of graphitic-N/pyridinic-N with oxygen reduction reaction (ORR) activity and pyridinic-N with oxygen evolution reaction (OER) activity for FFAEs, accelerating the mass transfer process of oxygen-active species. The resulting N-doped hollow carbon fiber films (NHCFs) exhibit superior bifunctional ORR/OER performance with a low potential difference of only 0.60 V. The rechargeable ZABs with NHCFs as metal-free cathodes possess a long-term cycling stability. Furthermore, the NHCFs can be used as FFAEs for flexible ZABs which have a high specific capacity and good cycling stability under different bending states. This work paves the way to design and produce highly active metal-free bifunctional FFAEs for electrochemical energy devices.

Lignin-derivable alternatives to bisphenol A with potentially undetectable estrogenic activity and minimal developmental toxicity

Lignin-derivable bisguaiacols/bissyringols are viable alternatives to commercial bisphenols; however, many bisguaiacols/bissyringols (e.g., bisguaiacol F [BGF]) have unsubstituted bridging carbons between the aromatic rings, making them more structurally similar to bisphenol F (BPF) than bisphenol A (BPA) - both of which are suspected endocrine disruptors. Herein, we investigated the estrogenic activity (EA) and developmental toxicity of dimethyl-substituted bridging carbon-based lignin-derivable bisphenols (bisguaiacol A [BGA] and bissyringol A [BSA]). Notably, BSA showed undetectable EA at seven test concentrations (from 10-12 M to 10-6 M) in the MCF-7 cell proliferation assay, whereas BPA had detectable EA at five concentrations (from 10-10 M to 10-6 M). In silico results indicated that BSA had the lowest binding affinity with estrogen receptors. Moreover, in vivo chicken embryonic assay results revealed that lignin-derivable monomers had minimal developmental toxicity vs. BPA at environmentally relevant test concentrations (8.7-116 μg/kg). Additionally, all lignin-derivable compounds showed significantly lower expression fold changes (from ∼1.81 to ∼4.41) in chicken fetal liver tests for an estrogen-response gene (apolipoprotein II) in comparison to BPA (fold change of ∼11.51), which was indicative of significantly reduced estrogenic response. Altogether, the methoxy substituents on lignin-derivable bisphenols appeared to be a positive factor in reducing the EA of BPA alternatives.

Characterization and properties of phenolic resin doped modified lignin

Phenolic resins occupy an important position in industrial applications, but phenol, one of the raw materials for synthesis, is a non-renewable resource. Lignin, as a natural polymer containing phenolic hydroxyl groups, alcohol hydroxyl groups and other reactive groups, can replace some of the phenol in the synthesis of phenolic resins, which can reduce the amount of phenol, thus reducing the cost of phenolic resins, while effectively promoting the high value-added use of renewable biomass resources. Due to its low reactivity, alkaline lignin is usually discharged as production waste, unaware that lignin macromolecules can be modified. In this paper, the phenolic monomers were obtained by acid-catalyzed depolymerization of DES (choline chloride/p-toluenesulfonic acid or choline chloride/lactic acid) from waste alkaline lignin, and the recovery rate of the DES solution during the catalytic treatment was more than 85 %, in which the main monomer was 2-methoxy-4-(1-propyl) phenol. The degradation of alkaline lignin is still favorable after five times of DES solvent recovery. The depolymerized lignin monomer replaced phenol by 50 wt% and then ternary co-polymerized with phenol and formaldehyde to form a biomass phenol-based phenolic resin, providing a green route for phenolic resin production. The cost of resin preparation was economically calculated, and it was found that the cost of resin after accumulating 4 cycles of DES treatment was only 51.1 % of that of pure phenolic resin. The density functional theory (DFT) was used to simulate the possible radical reactions in the intermediate process of phenolic resin reaction, to explore the microscopic mechanism and competition, to provide theoretical reference for further experimental realization of resin structure control and optimization, and to improve the theoretical system of resin synthesis.

One-Pot Catalytic Cascade for the Depolymerization of the Lignin β-O-4 Motif to Non-phenolic Dealkylated Aromatics

Aromatic monomers obtained by selective depolymerization of the lignin β-O-4 motif are typically phenolic and contain (oxygenated) alkyl substitutions. This work reveals the potential of a one-pot catalytic lignin β-O-4 depolymerization cascade strategy that yields a uniform set of methoxylated aromatics without alkyl side-chains. This cascade consists of the selective acceptorless dehydrogenation of the γ-hydroxy group, a subsequent retro-aldol reaction that cleaves the Cα-Cβ bond, followed by in situ acceptorless decarbonylation of the formed aldehydes. This three-step cascade reaction, catalyzed by an iridium(I)-BINAP complex, resulted in 75 % selectivity for 1,2-dimethoxybenzene from G-type lignin dimers, alongside syngas (CO : H2≈1.4 : 1). Applying this method to a synthetic G-type polymer, 11 wt % 1,2-dimethoxybenzene was obtained. This versatile compound can be easily transformed into 3,4-dimethoxyphenol, a valuable precursor for pharmaceutical synthesis, through an enzymatic catalytic approach. Moreover, the hydrodeoxygenation potential of 1,2-dimethoxybenzene offers a pathway to produce valuable cyclohexane or benzene derivatives, presenting enticing opportunities for sustainable chemical transformations without the necessity for phenolic mixture upgrading via dealkylation.

Quantification of Native Lignin Structural Features with Gel-Phase 2D-HSQC0 Reveals Lignin Structural Changes During Extraction

Our ability to study and valorize the lignin fraction of biomass is hampered by the fundamental and still unmet challenge of precisely quantifying native lignin's structural features. Here, we developed a rapid elevated-temperature 1H-13C Heteronuclear Single-Quantum Coherence Zero (HSQC0) NMR method that enables this precise quantification of native lignin structural characteristics even with whole plant cell wall (WPCW) NMR spectroscopy, overcoming fast spin relaxation in the gel phase. We also formulated a Gaussian fitting algorithm to perform automatic and reliable spectral integration. By combining HSQC0 measurements with yield measurements following depolymerisation, we can confirm the combinatorial nature of radical coupling reactions during biosynthesis leading to a random sequential organization of linkages within a largely linear lignin chain. Such analyses illustrate how this analytical method can greatly facilitate the study of native lignin structure, which can then be used for fundamental studies or to understand lignin depolymerization methods like reductive catalytic fractionation or aldehyde-assisted fractionation.

Maximizing Degumming Efficiency for Firmiana simplex Bark Using Deep Eutectic Solvents

Degumming is a critical process in the purification of natural fibers, essential for enhancing their quality and usability across various applications. Traditional degumming methods employed for natural fibers encounter inherent limitations, encompassing prolonged procedures, excessive energy consumption, adverse environmental impact, and subpar efficiency. To address these challenges, a groundbreaking wave of degumming technique has emerged, transcending these constraints and heralding a new era of efficiency, sustainability, and eco-friendly techniques. This study represents the Firmiana simplex bark (FSB) fiber's delignification by using deep eutectic solvents (DESs). The study explores the application of deep eutectic solvents, by synthesizing different types of DES using a hydrogen bond acceptor (HBA) and four representative hydrogen bond donors (HBDs) for FSB fiber degumming. This study investigates the morphologies, chemical compositions, crystallinities, and physical properties of Firmiana simplex bark fibers before and after the treatment. Furthermore, the effects and mechanisms of different DESs on dispersing FSB fibers were examined. The experimental results showed that choline chloride-urea (CU)-based DES initiates the degumming process by effectively disrupting the hydrogen bond interaction within FSB fibers, primarily by outcompeting chloride ions. Following this initial step, the DES acts by deprotonating phenolic hydroxyl groups and cleaving β-O-4 bonds present in diverse lignin units, thereby facilitating the efficient removal of lignin from the fibers. This innovative approach resulted in significantly higher degumming efficiency and ecofriendly as compared to traditional methods. Additionally, the results revealed that CU-based DES exhibits the utmost effectiveness in degumming FSB fibers. The optimal degumming conditions involve a precise processing temperature of 160 °C and a carefully controlled reaction time of 2 h yielding the most favorable outcomes. The present study presents a novel straightforward and environmentally friendly degumming method for Firmiana simplex bark, offering a substantial potential for enhancing the overall quality and usability of the resulting fibers. Our findings open new pathways for sustainable fiber-processing technologies.

Atomically dispersed cobalt catalysts for tandem synthesis of primary benzylamines from oxidized β-O-4 segments

This work presents an innovative approach focusing on fine-tuning the coordination environment of atomically dispersed cobalt catalysts for tandem synthesis of primary benzylamines from oxidized lignin model compounds. By meticulously regulating the Co-N coordination environment, the activity of these catalysts in the hydrogenolysis and reductive amination reactions was effectively controlled. Notably, our study demonstrates that, in contrast to cobalt nanoparticle catalysts, atomically dispersed cobalt catalysts exhibit precise control of the sequence of hydrogenolysis and reductive amination reactions. Particularly, the CoN3 catalyst with a triple Co-N coordination number achieved a remarkable 94% yield in the synthesis of primary benzylamine. To our knowledge, there is no previous documentation of the synthesis of primary benzylamines from lignin dimer model compounds. Our study highlights a promising one-pot route for sustainable production of nitrogen-containing aromatic chemicals from lignin.

Room temperature catalytic upgrading of unpurified lignin depolymerization oil into bisphenols and butene-2

Lignin is the largest source of renewable aromatics on earth. Despite numerous techniques for lignin depolymerization into mixtures of valuable monomers, methods for their upgrading into final products are scarce. The state of the art upgrading methods generally rely on catalytic funneling, requiring high temperatures, catalyst loadings and hydrogen pressure, and lead to the loss of functionality and bio-based carbon content. Here an alternative approach is presented, whereby the target monomers are selectively converted in unpurified mixtures into easily separable final products under mild conditions. We use reductive catalytic fractionation of wood to convert lignin into iso-eugenol and propenyl syringol enriched oil followed by an olefin metathesis to yield bisphenols and butene-2, thus, valorizing all bio-based carbons. To further demonstrate the synthetic utility of the obtained bisphenols we converted them into polyesters with a high glass transition temperature (Tg = 140.3 °C) and thermal stability (Td50% = 330 °C).

Enhancing monolignol ferulate conjugate levels in poplar lignin via OsFMT1

BACKGROUND

The phenolic polymer lignin is one of the primary chemical constituents of the plant secondary cell wall. Due to the inherent plasticity of lignin biosynthesis, several phenolic monomers have been shown to be incorporated into the polymer, as long as the monomer can undergo radicalization so it can participate in coupling reactions. In this study, we significantly enhance the level of incorporation of monolignol ferulate conjugates into the lignin polymer to improve the digestibility of lignocellulosic biomass.

RESULTS

Overexpression of a rice Feruloyl-CoA Monolignol Transferase (FMT), OsFMT1, in hybrid poplar (Populus alba x grandidentata) produced transgenic trees clearly displaying increased cell wall-bound ester-linked ferulate, p-hydroxybenzoate, and p-coumarate, all of which are in the lignin cell wall fraction, as shown by NMR and DFRC. We also demonstrate the use of a novel UV-Vis spectroscopic technique to rapidly screen plants for the presence of both ferulate and p-hydroxybenzoate esters. Lastly we show, via saccharification assays, that the OsFMT1 transgenic p oplars have significantly improved processing efficiency compared to wild-type and Angelica sinensis-FMT-expressing poplars.

CONCLUSIONS

The findings demonstrate that OsFMT1 has a broad substrate specificity and a higher catalytic efficiency compared to the previously published FMT from Angelica sinensis (AsFMT). Importantly, enhanced wood processability makes OsFMT1 a promising gene to optimize the composition of lignocellulosic biomass.

Postindustrial Jute Waste as a Support for Nano-Carbon Nitride Photocatalyst: Influence of Chemical Pretreatment

Non-woven jute (NWJ) produced from carpet industry waste was oxidized by H2O2 or alkali-treated by NaOH and compared with water-washed samples. Changes in the structure of the NWJ, tracked by X-ray diffraction (XRD), showed that both chemical treatments disrupt hydrogen bond networks between cellulose Iβ chains of the NWJ fibers. Thereafter, nano-carbon nitride (nCN) was impregnated, using a layer-by-layer technique, onto water-washed jute samples (nCN-Jw), NaOH-treated samples (nCN-Ja) and-H2O2 treated samples (nCN-Jo). Analysis of the Fourier transform infrared spectroscopy (FTIR) spectra of the impregnated samples revealed that nCN anchors to the water-washed NWJ surface through hemicellulose and secondary hydroxyl groups of the cellulose. In the case of chemically treated samples, nCN is preferentially bonded to the hydroxymethyl groups of cellulose. The stability and reusability of prepared nCN-jute (nCN-J) samples were assessed by tracking the photocatalytic degradation of Acid Orange 7 (AO7) dye under simulated solar light irradiation. Results from up to ten consecutive photocatalytic cycles demonstrated varying degrees of effectiveness across different samples. nCN-Jo and nCN-Ja samples exhibited declining effectiveness over cycles, attributed to bond instability between nCN and jute. In contrast, the nCN-Jw sample consistently maintained high degradation rates over ten cycles, with a dye removal percentage constantly above 90%.

The Synergetic Reduction of the Condensation Degree of Dissolved Lignin (DL) during the Refining Process of Wheat Straw Biomass Based on the MA/O3 System

Lignin, a natural pol2ymer with a complex structure that is difficult to separate, is prone to C-C bond condensation during the separation process. To reduce the condensation of lignin, here, a novel method is proposed for separating the components by using a combination of maleic acid (MA)/ozone (O3) to co-treat wheat straw. The removal of lignin, glucan, and xylan was 38.07 ± 0.2%, 31.44 ± 0.1%, and 71.98 ± 0.1%, respectively, under the conditions of ball-milling of wheat straw for 6 h, reaction temperature of 60 °C, and O3 holding time of 9 min. Lignin-rich solutions were collected to extract the dissolved lignin (DL) after washing the treated samples. The DL obtained under MA/O3 conditions had a carboxyl group (-COOH) content of 2.96 mmol/g. The carboxyl group of MA underwent esterification with the hydroxyl group (-OH) at the γ position of lignin and O3 reacted on the positions of the lignin side chain or the phenolic ring, resulting in a break in the side chain and the opening of the phenolic ring to introduce the carboxyl group. The 2D-HSQC-NMR results revealed that the phenolic ring-opening reaction of lignin in the presence of O3 was essentially free of β-β and β-5 condensation bonds.

Characterization techniques for tobacco and its derivatives: a systematic review

Biomass and its derivatives have broad applications in the fields of bio-catalysis, energy storage, environmental remediation. The structure and components of biomass, which are vital parameters affecting corresponding performances of derived products, need to be fully understood for further regulating the biomass and its derivatives. Herein, tobacco is taken as an example of biomass to introduce the typical characterization techniques in unraveling the structural information, chemical components, and properties of biomass and its derivatives. Firstly, the structural information, chemical components and application for biomass are summarized. Then the characterization techniques together with the resultant structural information and chemical components are introduced. Finally, to promote a wide and deep study in this field, the perspectives and challenges concerning structure and composition charaterization in biomass and its derivatives are put forward.

Parascedosporium putredinis NO1 tailors its secretome for different lignocellulosic substrates

Parascedosporium putredinis NO1 is a plant biomass-degrading ascomycete with a propensity to target the most recalcitrant components of lignocellulose. Here we applied proteomics and activity-based protein profiling (ABPP) to investigate the ability of P. putredinis NO1 to tailor its secretome for growth on different lignocellulosic substrates. Proteomic analysis of soluble and insoluble culture fractions following the growth of P. putredinis NO1 on six lignocellulosic substrates highlights the adaptability of the response of the P. putredinis NO1 secretome to different substrates. Differences in protein abundance profiles were maintained and observed across substrates after bioinformatic filtering of the data to remove intracellular protein contamination to identify the components of the secretome more accurately. These differences across substrates extended to carbohydrate-active enzymes (CAZymes) at both class and family levels. Investigation of abundant activities in the secretomes for each substrate revealed similar variation but also a high abundance of "unknown" proteins in all conditions investigated. Fluorescence-based and chemical proteomic ABPP of secreted cellulases, xylanases, and β-glucosidases applied to secretomes from multiple growth substrates for the first time confirmed highly adaptive time- and substrate-dependent glycoside hydrolase production by this fungus. P. putredinis NO1 is a promising new candidate for the identification of enzymes suited to the degradation of recalcitrant lignocellulosic feedstocks. The investigation of proteomes from the biomass bound and culture supernatant fractions provides a more complete picture of a fungal lignocellulose-degrading response. An in-depth understanding of this varied response will enhance efforts toward the development of tailored enzyme systems for use in biorefining.IMPORTANCEThe ability of the lignocellulose-degrading fungus Parascedosporium putredinis NO1 to tailor its secreted enzymes to different sources of plant biomass was revealed here. Through a combination of proteomic, bioinformatic, and fluorescent labeling techniques, remarkable variation was demonstrated in the secreted enzyme response for this ascomycete when grown on multiple lignocellulosic substrates. The maintenance of this variation over time when exploring hydrolytic polysaccharide-active enzymes through fluorescent labeling, suggests that this variation results from an actively tailored secretome response based on substrate. Understanding the tailored secretomes of wood-degrading fungi, especially from underexplored and poorly represented families, will be important for the development of effective substrate-tailored treatments for the conversion and valorization of lignocellulose.

Evolution and engineering of pathways for aromatic O-demethylation in Pseudomonas putida KT2440

Biological conversion of lignin from biomass offers a promising strategy for sustainable production of fuels and chemicals. However, aromatic compounds derived from lignin commonly contain methoxy groups, and O-demethylation of these substrates is often a rate-limiting reaction that influences catabolic efficiency. Several enzyme families catalyze aromatic O-demethylation, but they are rarely compared in vivo to determine an optimal biocatalytic strategy. Here, two pathways for aromatic O-demethylation were compared in Pseudomonas putida KT2440. The native Rieske non-heme iron monooxygenase (VanAB) and, separately, a heterologous tetrahydrofolate-dependent demethylase (LigM) were constitutively expressed in P. putida, and the strains were optimized via adaptive laboratory evolution (ALE) with vanillate as a model substrate. All evolved strains displayed improved growth phenotypes, with the evolved strains harboring the native VanAB pathway exhibiting growth rates ∼1.8x faster than those harboring the heterologous LigM pathway. Enzyme kinetics and transcriptomics studies investigated the contribution of selected mutations toward enhanced utilization of vanillate. The VanAB-overexpressing strains contained the most impactful mutations, including those in VanB, the reductase for vanillate O-demethylase, PP_3494, a global regulator of vanillate catabolism, and fghA, involved in formaldehyde detoxification. These three mutations were combined into a single strain, which exhibited approximately 5x faster vanillate consumption than the wild-type strain in the first 8 h of cultivation. Overall, this study illuminates the details of vanillate catabolism in the context of two distinct enzymatic mechanisms, yielding a platform strain for efficient O-demethylation of lignin-related aromatic compounds to value-added products.

Advanced tools for molecular characterization of bio-based and biodegradable polymers

Bio-based and biodegradable materials play a vital role in a sustainable and green economy. These materials must exhibit properties that are similar to or better than the properties of oil- or coal-based materials and require sophisticated synthesis technologies and detailed knowledge of structure-property correlations. For comprehensive molecular structure elucidation, advanced analytical methods, including coupled and hyphenated techniques that combine advanced fractionation and information-rich spectroscopic detectors, are an indispensable tool. One important tool for fractionating complex polymers regarding molecular size is size exclusion chromatography. For fractionating polymers with regard to chemical composition, solvent (or temperature) gradient HPLC has been developed. The combination of different liquid chromatography methods in comprehensive two-dimensional HPLC setups is another important tool. Today, a toolbox of HPLC methods is in place that enables the fractionation of complex bio-based and biodegradable polymers according to the most important molecular parameters including molecular size, composition, functionality, and branching. Here, an overview of the different techniques and some major applications is presented. Some representative developments in the field are discussed, and different techniques, experimental protocols, and applications are highlighted.

Enabling Lignin Valorization Through Integrated Advances in Plant Biology and Biorefining

Despite lignin having long been viewed as an impediment to the processing of biomass for the production of paper, biofuels, and high-value chemicals, the valorization of lignin to fuels, chemicals, and materials is now clearly recognized as a critical element for the lignocellulosic bioeconomy. However, the intended application for lignin will likely require a preferred lignin composition and form. To that end, effective lignin valorization will require the integration of plant biology, providing optimal feedstocks, with chemical process engineering, providing efficient lignin transformations. Recent advances in our understanding of lignin biosynthesis have shown that lignin structure is extremely diverse and potentially tunable, while simultaneous developments in lignin refining have resulted in the development of several processes that are more agnostic to lignin composition. Here, we review the interface between in planta lignin design and lignin processing and discuss the advances necessary for lignin valorization to become a feature of advanced biorefining.

Safety profiling of technical lignins originating from various bioresources and conversion processes

In this work, a set of eight technical lignin samples from various botanical origins and production processes were characterized for their chemical composition, higher heating value, size distribution, dust explosion sensitivity and severity, thermal hazard characteristics and biodegradability, in further support of their sustainable use. More specifically, safety-focused parameters have been assessed in terms of consistency with relating physico-chemical properties determined for the whole set of technical lignins. The results emphasized the heterogeneity and variability of technical lignins and the subsequent need for a comprehensive characterization of new lignin feedstocks arising from novel biorefineries. Indeed, significant differences were revealed between the samples in terms of hazards sensitivity. This first comparative physico-chemical safety profiling of technical lignins could be useful for the hazard analysis and the safe design of the facilities associated with large scale valorisation of biomass residues such as lignins, targeting "zero waste" sustainable conversion of bioresources.

The Versatile and Strategic O-Carbamate Directed Metalation Group in the Synthesis of Aromatic Molecules: An Update

The aryl O-carbamate (ArOAm) group is among the strongest of the directed metalation groups (DMGs) in directed ortho metalation (DoM) chemistry, especially in the form Ar-OCONEt2. Since the last comprehensive review of metalation chemistry involving ArOAms (published more than 30 years ago), the field has expanded significantly. For example, it now encompasses new substrates, solvent systems, and metalating agents, while conditions have been developed enabling metalation of ArOAm to be conducted in a green and sustainable manner. The ArOAm group has also proven to be effective in the anionic ortho-Fries (AoF) rearrangement, Directed remote metalation (DreM), iterative DoM sequences, and DoM-halogen dance (HalD) synthetic strategies and has been transformed into a diverse range of functionalities and coupled with various groups through a range of cross-coupling (CC) strategies. Of ultimate value, the ArOAm group has demonstrated utility in the synthesis of a diverse range of bioactive and polycyclic aromatic compounds for various applications.

Hydrogen-transfer strategy in lignin refinery: Towards sustainable and versatile value-added biochemicals

Lignin, the most prevalent natural source of polyphenols on Earth, offers substantial possibilities for the conversion into aromatic compounds, which is critical for attaining sustainability and carbon neutrality. The hydrogen-transfer method has garnered significant interest owing to its environmental compatibility and economic viability. The efficacy of this approach is contingent upon the careful selection of catalytic and hydrogen-donating systems that decisively affect the yield and selectivity of the monomeric products resulting from lignin degradation. This paper highlights the hydrogen-transfer technique in lignin refinery, with a specific focus on the influence of hydrogen donors on the depolymerization pathways of lignin. It delineates the correlation between the structure and activity of catalytic hydrogen-transfer arrangements and the gamut of lignin-derived biochemicals, utilizing data from lignin model compounds, separated lignin, and lignocellulosic biomass. Additionally, the paper delves into the advantages and future directions of employing the hydrogen-transfer approach for lignin conversion. In essence, this concept investigation illuminates the efficacy of the hydrogen-transfer paradigm in lignin valorization, offering key insights and strategic directives to maximize lignin's value sustainably.

Design and Validation of a High-Throughput Reductive Catalytic Fractionation Method

Reductive catalytic fractionation (RCF) is a promising method to extract and depolymerize lignin from biomass, and bench-scale studies have enabled considerable progress in the past decade. RCF experiments are typically conducted in pressurized batch reactors with volumes ranging between 50 and 1000 mL, limiting the throughput of these experiments to one to six reactions per day for an individual researcher. Here, we report a high-throughput RCF (HTP-RCF) method in which batch RCF reactions are conducted in 1 mL wells machined directly into Hastelloy reactor plates. The plate reactors can seal high pressures produced by organic solvents by vertically stacking multiple reactor plates, leading to a compact and modular system capable of performing 240 reactions per experiment. Using this setup, we screened solvent mixtures and catalyst loadings for hydrogen-free RCF using 50 mg poplar and 0.5 mL reaction solvent. The system of 1:1 isopropanol/methanol showed optimal monomer yields and selectivity to 4-propyl substituted monomers, and validation reactions using 75 mL batch reactors produced identical monomer yields. To accommodate the low material loadings, we then developed a workup procedure for parallel filtration, washing, and drying of samples and a 1H nuclear magnetic resonance spectroscopy method to measure the RCF oil yield without performing liquid-liquid extraction. As a demonstration of this experimental pipeline, 50 unique switchgrass samples were screened in RCF reactions in the HTP-RCF system, revealing a wide range of monomer yields (21-36%), S/G ratios (0.41-0.93), and oil yields (40-75%). These results were successfully validated by repeating RCF reactions in 75 mL batch reactors for a subset of samples. We anticipate that this approach can be used to rapidly screen substrates, catalysts, and reaction conditions in high-pressure batch reactions with higher throughput than standard batch reactors.

Advancing Lignocellulosic Biomass Fractionation through Molten Salt Hydrates: Catalyst-Enhanced Pretreatment for Sustainable Biorefineries

Developing a process that performs the lignocellulosic biomass fractionation under milder conditions simultaneously with the depolymerization and/or the upgrading of all fractions is fundamental for the economic viability of future lignin-first biorefineries. The molten salt hydrates (MSH) with homogeneous or heterogeneous catalysts are a potential alternative to biomass pretreatment that promotes cellulose's dissolution and its conversion to different platform molecules while keeping the lignin reactivity. This review investigates the fractionation of lignocellulosic biomass using MSH to produce chemicals and fuels. First, the MSH properties and applications are discussed. In particular, the use of MSH in cellulose dissolution and hydrolysis for producing high-value chemicals and fuels is presented. Then, the biomass treatment with MSH is discussed. Different strategies for preventing sugar degradation, such as biphasic media, adsorbents, and precipitation, are contrasted. The potential for valorizing isolated lignin from the pretreatment with MSH is debated. Finally, challenges and limitations in utilizing MSH for biomass valorization are discussed, and future developments are presented. Cellulose Avicel®PH-101 ZnCl2 ⋅ 4H2O, ZnBr2 ⋅ 4H2O, LiCl ⋅ 8H2O, LiBr ⋅ 4H2O H2SO4, (0.2 M); H3PW12O40 (0.067 M); H4SiW12O40 (0.05 M) T (145-175 °C); Time (30-120 min) Organic solvent (MIBK) LA (94 %) and HMF (3.4 %) Dissolution time: ZnBr2 ⋅ 4H2O<>2O<>2 ⋅ 4H2O<>2O; The highest conversion of pretreated cellulose and yield of glucose were obtained with ZnBr2 ⋅ 4H2O (88 % and 80 %, respectively).