Method for the Determination of Carbonyl Compounds in E-Cigarette Aerosols

Analytical methods and experimental quality in studies targeting carbonyls in electronic cigarette aerosols

We provide an extensive review of 14 studies (11 independent and three industry-funded) on emissions generated by Electronic Cigarettes (ECs), specifically focusing on the evaluation of carbonyls present in these emissions and emphasizing a meticulous evaluation of their analytical methods and experimental procedures. Since the presence of carbonyl by-products in EC aerosol is concerning, it is important to evaluate the reliability of emission studies quantifying these compounds by verifying their compliance with the following criteria of experimental quality: authors must 1) supply sufficient information on the devices and experimental procedures to allow for potentially reproducing or replicating the experiments, 2) use of appropriate puffing protocols that approach consumer usage as best as possible, 3) use of appropriate analytical methods and 4) usage of blank samples to avoid false positive detection. Outcomes were classified in terms of the fulfilment of these conditions as reliable in seven studies, partially reliable in five studies, and unreliable in two studies. However, only five studies used blank samples and six studies failed the reproducibility criterion. Carbonyl yields were far below their yields in tobacco smoke in all reproducible studies, even in the partially reliable ones, thus supporting the role of ECs (when properly tested and operated) as harm reduction products. This review highlights the necessity to evaluate the quality of laboratory standards in testing EC emissions to achieve an objective assessment of the risk profile of ECs.

The role of β-Nicotyrine in E-Cigarette abuse liability I: Drug Discrimination

Background

β-Nicotyrine (β-Nic) is a unique minor alkaloid constituent in electronic nicotine delivery systems (ENDS) that is derived from nicotine (Nic) degradation and can reach 25% of Nic concentrations in ENDS aerosol. β-Nic slows Nic metabolism and prolongs systemic Nic exposure, which may alter the discriminability of Nic. The present study sought to examine β-Nic has interoceptive effects itself, and if it alters the subjective effects ENDS products within a drug-discrimination paradigm.

Methods

The pharmacodynamics of β-Nic were examined in vitro, and a nicotine discrimination paradigm was used to determine if β-Nic (0 - 5.0 mg/kg) shares discriminative stimulus properties with Nic (0.2 mg/kg) in male (n = 13) and female (n = 14) rats after 10- & 60-min β-Nic pretreatment delays. A second group of rats was trained to discriminate β-Nic and Nornicotine (Nornic) from saline to determine if β-Nic alone has interoceptive properties and whether they are similar to Nornic.

Results

β-Nic had similar binding affinity and efficacy at the α4β2 nicotinic receptor subtype as Nornic, ~50% of Nic efficacy. However, β-Nic only weakly substituted for Nic during substitution testing in female rats, but not males, whereas Nornic fully substituted for Nic. Combination testing at the 10 and 60-min pretreatment intervals showed that β-Nic dose-dependently increased the duration of nicotine's discriminative stimulus effects, especially at the 60-min delay. Drug naïve rats could reliably discriminate Nornic, but not β-Nic, from Sal.

Conclusion

β-Nic increased and prolonged the interoceptive stimulus properties of Nic, suggesting it may alter to the abuse liability of ENDS through its ability to slow Nic metabolism.

Harmful and Potentially Harmful Constituents in E-Liquids and Aerosols from Electronic Nicotine Delivery Systems (ENDS)

In 2012, the U.S. Food & Drug Administration (FDA) published an established list of 93 harmful and potentially harmful constituents (HPHCs) targeting four tobacco product types (cigarettes, cigarette tobacco, roll-your-own tobacco, smokeless tobacco). In 2016, the FDA finalized the deeming rule to regulate electronic nicotine delivery systems (ENDS). However, knowledge gaps exist regarding whether certain HPHCs are present in ENDS e-liquids and aerosols. We identified and addressed these gaps by conducting literature searches and then experimentally quantifying HPHCs in the e-liquid and aerosol of 37 ENDS brands based on gaps in the literature. The literature searches identified 66 e-liquid HPHCs and 68 aerosol HPHCs that have limited to no information regarding the quantifiability of these constituents. A contracted ISO 17025 accredited laboratory performed the HPHC quantifications. The availability of validated analytical methods in the contracted laboratory determined the HPHCs included in the study scope (63/66 for e-liquids, 64/68 for aerosols). Combining the results from the quantifications and literature searches, 36 (39%) and 34 (37%) HPHCs were found quantifiable (≥limit of quantification [LOQ]) in ENDS e-liquids and aerosols, respectively, with 25 HPHCs being quantifiable in both matrices. Quantifiability results imply potential HPHC transfers between matrices, leaching from components, or formations from aerosol generation. The study results can inform the scientific basis for manufacturers and regulators regarding regulatory requirements for HPHC reporting. The HPHC quantities can also inform evaluations of the public health impact of ENDS and public communications regarding ENDS health risks.

Conventional and multi-omics assessments of subacute inhalation toxicity due to propylene glycol and vegetable glycerin aerosol produced by electronic cigarettes

Propylene glycol (PG) and vegetable glycerin (VG) are the most common solvents used in electronic cigarette liquids. No long-term inhalation toxicity assessments have been performed combining conventional and multi-omics approaches on the potential respiratory effects of the solvents in vivo. In this study, the systemic toxicity of aerosol generated from a ceramic heating coil-based e-cigarette was evaluated. First, the aerosol properties were characterized, including carbonyl emissions, the particle size distribution, and aerosol temperatures. To determine toxicological effects, rats were exposed, through their nose only, to filtered air or a propylene glycol (PG)/ glycerin (VG) (50:50, %W/W) aerosol mixture at the target concentration of 3 mg/L for six hours daily over a continuous 28-day period. Compared with the air group, female rats in the PG/VG group exhibited significantly lower body weights during both the exposure period and recovery period, and this was linked to a reduced food intake. Male rats in the PG/VG group also experienced a significant decline in body weight during the exposure period. Importantly, rats exposed to the PG/VG aerosol showed only minimal biological effects compared to those with only air exposure, with no signs of toxicity. Moreover, the transcriptomic, proteomic, and metabolomic analyses of the rat lung tissues following aerosol exposure revealed a series of candidate pathways linking aerosol inhalation to altered lung functions, especially the inflammatory response and disease. Dysregulated pathways of arachidonic acids, the neuroactive ligand-receptor interaction, and the hematopoietic cell lineage were revealed through integrated multi-omics analysis. Therefore, our integrated multi-omics approach offers novel systemic insights and early evidence of environmental-related health hazards associated with an e-cigarette aerosol using two carrier solvents in a rat model.

Increased oxidative stress responses in murine macrophages exposed at the air-liquid interface to third- and fourth-generation electronic nicotine delivery system (ENDS) aerosols

Background

New fourth generation electronic nicotine delivery system (ENDS) devices contain high levels of nicotine salt (up to 60 mg/mL), whose cellular and molecular effects on immune cells are currently unknown. Here, we used a physiologically-relevant in vitro air-liquid interface (ALI) exposure model to assess the toxicity of distinct ENDS, a 3rd-generation electronic-cigarette (e-cig) and two 4th-generation ENDS devices (JUUL and Posh Plus).

Methods

Murine macrophages (RAW 264.7) were exposed at the ALI to either air, Menthol or Crème Brûlée-flavored ENDS aerosols generated from those devices for 1-hour per day for 1 or 3 consecutive days. Cellular and molecular toxicity was evaluated 24 h post-exposure.

Results

1-day of Menthol-flavored JUUL aerosol exposure significantly decreased cell viability and significantly increased lactate dehydrogenase (LDH) levels compared to air controls. Further, JUUL Menthol elicited significantly increased reactive oxygen species (ROS) and nitric oxide (NO) production compared to air controls. Posh Crème Brûlée-flavored aerosols displayed significant cytotoxicity - decreased cell viability and increased LDH levels -after 1- and 3-day exposures, while the Crème Brûlée-flavored aerosol produced by the 3rd-generation e-cig device only displayed significant cytotoxicity after 3 days compared to air controls. Further, both Posh and third-generation e-cig Crème Brûlée flavored-aerosols elicited significantly increased ROS plus high levels of 8-isoprostane after 1 and 3 days compared to air controls, indicating increased oxidative stress. Posh and third-generation e-cig Crème Brûlée flavored-aerosols elicited reduction in NO levels after one day, but elicited increase in NO after 3 days. Genes in common dysregulated by both devices after 1 day included α7nAChR, Cyp1a1, Ahr, Mmp12, and iNos.

Conclusion

Our results suggest that ENDS Menthol and Crème Brûlée-flavored aerosol exposures from both 3rd- and 4th-generation ENDS devices are cytotoxic to macrophages and cause oxidative stress. This can translate into macrophage dysfunction. Although 4th-generation disposable ENDS devices have no adjustable operational settings and are considered low-powered ENDS devices, their aerosols can induce cellular toxicity compared to air-exposed control cells. This study provides scientific evidence for regulation of nicotine salt-based disposable ENDS products.

Making Every Single Puff Count-Simple and Sensitive E-Cigarette Aerosol Sampling for GCxIMS and GC-MS Analysis

The analysis of the aerosol from tobaccoless electronic cigarettes (e-cigarettes) is an important part of understanding their impact on human health, yet sampling aerosol from e-cigarettes is still considered a challenge. It lacks a standard method for research and quality control and there are a variety of methods. However, few are simple and inexpensive, and none have been suggested for the use with gas chromatography coupled ion mobility spectrometry (GCxIMS). This work presents and evaluates such a setup made from standard lab equipment to quickly collect a quantitative sample from the aerosol of a single puff (5 s totaling 125 mL). The aerosol condensates directly in the cooled headspace (HS) vial, which is analyzed in the HS-GCxIMS or mass spectrometer (HS-GC-MS). The combined use of GC-MS and GCxIMS allows the simple and sensitive identification of unknown substances in complex mixtures and the identification of degradation products in the aerosols. A calibration of 26 flavor compounds (0.2-20 µg/g) was created using single puffs of a spiked, flavorless commercial refill solution and 2-alkanones as internal standards. This sensitive but easily reproducible setup enables a wide range of further investigations, even for labs that were previously unable to afford it.

Determination of chemical constituent yields in e-cigarette aerosol using partial and whole pod collections, a comparative analysis

Literature reports the chemical constituent yields of electronic nicotine delivery systems (ENDS) aerosol collected using a range of aerosol collection strategies. The number of puffs to deplete an ENDS product varies widely, but collections often consist of data from the first 50-100 puffs. However, it is not clear whether these discrete puff blocks are representative of constituent yields over the life of a pod. We aimed to assess the effect of differing aerosol collection strategies on reported yields for select chemical constituents in the aerosol of closed pod-based ENDS products. Constituents analyzed were chosen to reflect important classes of compounds from the Final Premarket Tobacco Product Application Guidance. Yields were normalized to total device mass loss (DML). Collection strategies that consisted of partial pod collection were valid for determining yields of constituents whose DML normalized yields were consistent for the duration of pod life. These included primary aerosol constituents, such as propylene glycol, glycerol, and nicotine, and whole pod yields could be determined from initial puff blocks. However, changes were observed in the yields of some metals, some carbonyl compounds, and glycidol over pod life in a chemical constituent and product dependent manner. These results suggest that collection strategies consisting of initial puff block collections require validation per chemical constituent/product and are not appropriate for chemical constituents with variable yields over pod life. Whole pod collection increased sensitivity and accuracy in determining metal, carbonyl, and glycidol yields compared to puff block-based collection methodologies for all products tested.

Xenobiotics Delivered by Electronic Nicotine Delivery Systems: Potential Cellular and Molecular Mechanisms on the Pathogenesis of Chronic Kidney Disease

Chronic kidney disease (CKD) is characterized as sustained damage to the renal parenchyma, leading to impaired renal functions and gradually progressing to end-stage renal disease (ESRD). Diabetes mellitus (DM) and arterial hypertension (AH) are underlying diseases of CKD. Genetic background, lifestyle, and xenobiotic exposures can favor CKD onset and trigger its underlying diseases. Cigarette smoking (CS) is a known modified risk factor for CKD. Compounds from tobacco combustion act through multi-mediated mechanisms that impair renal function. Electronic nicotine delivery systems (ENDS) consumption, such as e-cigarettes and heated tobacco devices, is growing worldwide. ENDS release mainly nicotine, humectants, and flavorings, which generate several byproducts when heated, including volatile organic compounds and ultrafine particles. The toxicity assessment of these products is emerging in human and experimental studies, but data are yet incipient to achieve truthful conclusions about their safety. To build up the knowledge about the effect of currently employed ENDS on the pathogenesis of CKD, cellular and molecular mechanisms of ENDS xenobiotic on DM, AH, and kidney functions were reviewed. Unraveling the toxic mechanisms of action and endpoints of ENDS exposures will contribute to the risk assessment and implementation of proper health and regulatory interventions.

Influence of Nitrite on Formation of Tobacco-Specific Nitrosamines in Electronic Cigarette Liquids and Aerosols

Tobacco-specific nitrosamine (TSNA) formation occurred during aerosol generation from select commercial cig-a-like e-cigarette products. To understand the drivers behind the potential formation of TSNAs in electronic cigarette (e-cigarette) aerosols and e-liquids, model e-liquid systems were generated in the lab to demonstrate that nitrite can react with nicotine and minor alkaloids to form TSNAs in e-liquids. In the presence of nitrite and nicotine, TSNA levels in e-liquids increased over time and the process was accelerated by elevated temperature. Additionally, TSNAs formed during aerosol generation when nitrite was present in the corresponding e-liquids. The commercial e-cigarette products that showed higher levels and formation of TSNAs were observed to contain nitrite and minor alkaloid impurities in the corresponding e-liquids. This study provides valuable information about drivers for TSNA formation in e-liquids and e-cigarette aerosols that may be applied to the evaluation and quality assurance of e-cigarette products.

Examining Metal Contents in Primary and Secondhand Aerosols Released by Electronic Cigarettes

The usage of electronic cigarettes (ECs) has surged since their invention two decades ago. However, to date, the health effects of EC aerosol exposure are still not well understood because of insufficient data on the chemical composition of EC aerosols and the corresponding evidence of health risks upon exposure. Herein, we quantified the metals in primary and secondhand aerosols generated by three brands of ECs. By combining aerosol filter sampling and inductively coupled plasma mass spectrometry (ICP-MS), we assessed the mass of metals as a function of EC flavoring, nicotine concentration, device power, puff duration, and aging of the devices. The masses of Cr, Cu, Mn, Ni, Cu, and Zn were consistently high across all brands in the primary and secondhand aerosols, some of which were above the regulated maximum daily intake amount, especially for Cr and Ni with mass (nanograms per 10 puffs) emitted at 117 ± 54 and 50 ± 24 (JUUL), 125 ± 77 and 219 ± 203 (VOOPOO), and 33 ± 10 and 27 ± 2 (Vapor4Life). Our analysis indicates that the metals are predominantly released from the EC liquid, potentially through mechanisms such as bubble bursting or the vaporization of metal-organic compounds. High metal contents were also observed in simulated secondhand aerosols, generally 80-90% of those in primary aerosols. Our findings provide a more detailed understanding of the metal emission characteristics of EC for assessing its health effects and policymaking.

High-Performance Liquid Chromatography-Tandem Mass Spectrometry Analysis of Carbonyl Emissions from E-Cigarette, or Vaping, Products

A quantitative method was developed to measure four harmful carbonyls (acetaldehyde, acrolein, crotonaldehyde, and formaldehyde) in aerosol generated from e-cigarette, or vaping, products (EVPs). The method uses a commercially available sorbent bed treated with a derivatization solution to trap and stabilize reactive carbonyls in aerosol emissions from EVPs to reduce reactive analyte losses and improve quantification. Analytes were extracted from the sorbent material using acetonitrile and analyzed via high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS). The method was applied to aerosols generated from products obtained from case patients with EVP use-associated lung injury (EVALI). The method accuracy ranged from 93.6 to 105% in the solvent and 99.0 to 112% in the matrix. Limits of detection (LODs) were in the low nanogram range at 0.735-2.10 ng for all analytes, except formaldehyde at 14.7 ng. Intermediate precision, as determined from the replicate measurements of quality-control (QC) samples, showed a relative standard deviation (RSD) of less than 20% for all analytes. The EVALI case-related products delivered aerosol containing the following ranges of carbonyls: acetaldehyde (0.0856-5.59 μg), acrolein (0.00646-1.05 μg), crotonaldehyde (0.00168-0.108 μg), and formaldehyde (0.0533-12.6 μg). At least one carbonyl analyte was detected in every product. Carbonyl deliveries from EVALI-associated products of all types are consistent with the previously published results for e-cigarettes, and levels are lower than those observed in smoke from combustible cigarettes. This method is rugged, has high throughput, and is well suited for quantifying four harmful carbonyls in aerosol emissions produced by a broad spectrum of devices/solvents, ranging from e-cigarette containing polar solvents to vaping products containing nonpolar solvents.

An Automated Aerosol Collection and Extraction System to Characterize Electronic Cigarette Aerosols

Electronic cigarette (e-cigarette) market increased by 122% during 2014–2020 and is expected to continue growing rapidly. Despite their popularity, e-cigarettes are known to emit dangerous levels of toxic compounds (e.g., carbonyls), but a lack of accurate and efficient testing methods is hindering the characterization of e-cigarette aerosols emitted by a wide variety of e-cigarette devices, e-liquids, and use patterns. The aim of this study is to fill this gap by developing an automated E-cigarette Aerosol Collection and Extraction System (E-ACES) consisting of a vaping machine and a collection/extraction system. The puffing system was designed to mimic e-cigarette use patterns (i.e., power output and puff topography) by means of a variable power-supply and a flow control system. The sampling system collects e-cigarette aerosols using a combination of glass wool and a continuously wetted denuder. After the collection stage, the system is automatically washed with absorbing and extracting liquids (e.g., methanol, an acetaldehyde-DNPH solution). The entire system is controlled by a computer. E-ACES performance was evaluated against conventional methods during measurements of nicotine and carbonyl emissions from a tank type e-cigarette. Nicotine levels measured using glass fiber filters and E-ACES were not significantly different: 201.2 ± 6.2 and 212.5 ± 17 μg/puff (p = 0.377), respectively. Differences in formaldehyde and acetaldehyde levels between filter-DNPH cartridges and the E-ACES were 14% (p = 0.057) and 13% (p = 0.380), respectively. The E-ACES showed reproducible nicotine and carbonyl testing results for the selected e-cigarette vaping conditions.

Targeted Characterization of the Chemical Composition of JUUL Systems Aerosol and Comparison with 3R4F Reference Cigarettes and IQOS Heat Sticks

Aerosol constituent yields have been reported from a wide range of electronic nicotine delivery systems. No comprehensive study has been published on the aerosol constituents generated from the JUUL system. Targeted analyses of 53 aerosol constituents from the four JUUL products currently on the US market (Virginia Tobacco and Menthol flavored e-liquids in both 5.0% and 3.0% nicotine concentration by weight) was performed using non-intense and intense puffing regimens. All measurements were conducted by an ISO 17025 accredited contract research organization. JUUL product aerosol constituents were compared to published values for the 3R4F research cigarette and IQOS Regular and Menthol heated tobacco products. Across the four JUUL products and two puffing regimes, only 10/53 analytes were quantifiable, including only two carbonyls (known propylene glycol or glycerol degradants). The remaining analytes were primary ingredients, nicotine degradants and water. Average analyte reductions (excluding primary ingredients and water) for all four JUUL system aerosols tested were greater than 98% lower than 3R4F mainstream smoke, and greater than 88% lower than IQOS aerosol. In summary, chemical characterization and evaluation of JUUL product aerosols demonstrates a significant reduction in toxicants when compared to mainstream cigarette smoke from 3R4F reference cigarettes or aerosols from IQOS-heated tobacco products.

Non-Targeted Analysis Using Gas Chromatography-Mass Spectrometry for Evaluation of Chemical Composition of E-Vapor Products

The Premarket Tobacco Product Applications (PMTA) guidance issued by the Food and Drug Administration for electronic nicotine delivery systems (ENDSs) recommends that in addition to reporting harmful and potentially harmful constituents (HPHCs), manufacturers should evaluate these products for other chemicals that could form during use and over time. Although e-vapor product aerosols are considerably less complex than mainstream smoke from cigarettes and heated tobacco product (HTP) aerosols, there are challenges with performing a comprehensive chemical characterization. Some of these challenges include the complexity of the e-liquid chemical compositions, the variety of flavors used, and the aerosol collection efficiency of volatile and semi-volatile compounds generated from aerosols. In this study, a non-targeted analysis method was developed using gas chromatography-mass spectrometry (GC-MS) that allows evaluation of volatile and semi-volatile compounds in e-liquids and aerosols of e-vapor products. The method employed an automated data analysis workflow using Agilent MassHunter Unknowns Analysis software for mass spectral deconvolution, peak detection, and library searching and reporting. The automated process ensured data integrity and consistency of compound identification with >99% of known compounds being identified using an in-house custom mass spectral library. The custom library was created to aid in compound identifications and includes over 1,100 unique mass spectral entries, of which 600 have been confirmed from reference standard comparisons. The method validation included accuracy, precision, repeatability, limit of detection (LOD), and selectivity. The validation also demonstrated that this semi-quantitative method provides estimated concentrations with an accuracy ranging between 0.5- and 2.0-fold as compared to the actual values. The LOD threshold of 0.7 ppm was established based on instrument sensitivity and accuracy of the compounds identified. To demonstrate the application of this method, we share results from the comprehensive chemical profile of e-liquids and aerosols collected from a marketed e-vapor product. Applying the data processing workflow developed here, 46 compounds were detected in the e-liquid formulation and 55 compounds in the aerosol sample. More than 50% of compounds reported have been confirmed with reference standards. The profiling approach described in this publication is applicable to evaluating volatile and semi-volatile compounds in e-vapor products.

Determination of Formaldehyde Yields in E-Cigarette Aerosols: An Evaluation of the Efficiency of the DNPH Derivatization Method

Recent reports have suggested that (1) formaldehyde levels (measured as a hydrazone derivative using the DNPH derivatization method) in Electronic Nicotine Delivery Systems (ENDS) products were underreported because formaldehyde may react with propylene glycol (PG) and glycerin (Gly) in the aerosol to form hemiacetals; (2) the equilibrium would shift from the hemiacetals to the acetals in the acidic DNPH trapping solution. In both cases, neither the hemiacetal nor the acetal would react with DNPH to form the target formaldehyde hydrazone, due to the lack of the carbonyl functional group, thus underreporting formaldehyde. These reports were studied in our laboratory. Our results showed that the aerosol generated from formaldehyde-fortified e-liquids provided a near-quantitative recovery of formaldehyde in the aerosol, suggesting that if any hemiacetal was formed in the aerosol, it would readily hydrolyze to free formaldehyde and, consequently, form formaldehyde hydrazone in the acidic DNPH trapping solution. We demonstrated that custom-synthesized Gly and PG hemiacetal adducts added to the DNPH trapping solution would readily hydrolyze to form the formaldehyde hydrazone. We demonstrated that acetals of PG and Gly present in e-liquid are almost completely transferred to the aerosol during aerosolization. The study results demonstrate that the DNPH derivatization method allows for an accurate measurement of formaldehyde in vapor products.

Assessment of Serum Concentrations of 12 Aldehydes in the U.S. Population from the 2013-2014 National Health and Nutrition Examination Survey

Aldehydes are known carcinogens and irritants that can negatively impact health. They are present in tobacco smoke, the environment, and food. The prevalence of aldehyde exposure and potential health impact warrants a population-wide study of serum aldehydes as exposure biomarkers. We analyzed 12 aldehydes in sera collected from 1843 participants aged 12 years or older in the 2013-2014 National Health and Nutrition Examination Survey. Several aldehydes were detected at high rates, such as isopentanaldehyde (99.2%) and propanaldehyde (88.3%). We used multiple linear regression models to examine the impact of tobacco smoke and dietary variables on serum concentrations of isopentanaldehyde and propanaldehyde. Although 12 serum aldehydes were analyzed and compared to tobacco smoke exposure, only isopentanaldehyde and propanaldehyde showed any significant association with tobacco smoke exposure. Survey participants who smoked 1-10 cigarettes per day (CPD) had 168% higher serum isopentanaldehyde and 28% higher propanaldehyde compared with nonusers. Study participants who smoked 11-20 CPD had higher serum isopentanaldehyde (323%) and propanaldehyde (70%). Similarly, study participants who smoked >20 CPD had 399% higher serum isopentanaldehyde and 110% higher serum propanaldehyde than nonexposed nonusers. The method could not, however, differentiate between nonexposed nonusers and nonusers exposed to secondhand smoke for either of these two aldehydes. No dietary variables were consistently predictive of serum isopentanaldehyde and propanaldehyde concentrations. This report defines baseline concentrations of serum aldehydes in the U.S. population and provides a foundation for future research into the potential health effects of aldehydes. In addition, this study suggests that tobacco smoke is a significant source of exposure to some aldehydes such as isopentanaldehyde and propanaldehyde.

A 7-month inhalation toxicology study in C57BL/6 mice demonstrates reduced pulmonary inflammation and emphysematous changes following smoking cessation or switching to e-vapor products

Cigarette smoking causes serious diseases, including lung cancer, atherosclerotic coronary artery disease, peripheral vascular disease, chronic bronchitis, and emphysema. While cessation remains the most effective approach to minimize smoking-related disease, alternative non-combustible tobacco-derived nicotine-containing products may reduce disease risks among those unable or unwilling to quit. E-vapor aerosols typically contain significantly lower levels of smoke-related harmful and potentially harmful constituents; however, health risks of long-term inhalation exposures are unknown. We designed a 7-month inhalation study in C57BL/6 mice to evaluate long-term respiratory toxicity of e-vapor aerosols compared to cigarette smoke and to assess the impact of smoking cessation (Cessation group) or switching to an e-vapor product (Switching group) after 3 months of exposure to 3R4F cigarette smoke (CS). There were no significant changes in in-life observations (body weights, clinical signs) in e-vapor groups compared to the Sham Control. The 3R4F CS group showed reduced respiratory function during exposure and had lower body weight and showed transient signs of distress post-exposure. Following 7 months of exposure, e-vapor aerosols resulted in no or minimal increase in pulmonary inflammation, while exposure to 3R4F CS led to impairment of lung function and caused marked lung inflammation and emphysematous changes. Biological changes observed in the Switching group were similar to the Cessation group. 3R4F CS exposure dysregulated the lung and nasal tissue transcriptome, while these molecular effects were substantially lower in the e-vapor group. Results from this study demonstrate that in comparison with 3R4F CS, e-vapor aerosols induce substantially lower biological responses including pulmonary inflammation and emphysematous changes, and that complete switching from CS to e-vapor products significantly reduces biological changes associated with CS in C57BL/6 mice.

E-cigarette aerosol collection using converging and straight tubing Sections: Physical mechanisms

HYPOTHESIS

Identification and quantification of harmful chemicals in e-cigarette aerosol requires collecting the aerosolized e-liquid for chemical analysis. In 2016, Olmedo at al. empirically developed a simple method for aerosol collection by directing the aerosol through a sequence of alternating straight and converging tubing sections, which drain the recovered e-liquid into a collection vial. The tubing system geometry and flow conditions promote inertial impaction of aerosolized e-liquid on tube walls, where it deposits and flows into the collection vial.

EXPERIMENTS

We use high-speed optical imaging to visualize aerosol transport in proxies of the collection system. We also determined collection efficiencies of various configurations of the collection system.

FINDINGS

A turbulent jet emerges from converging conical sections and impinges onto the wall of downstream tubing sections, resulting in inertial impaction and deposition of the aerosol. For inertial impaction to occur the tip radius of the converging section must be small enough for a jet to be formed and the sequence of tubing sections must be curved in a polygon-like manner such that the jet emerging from a converging section impinges on the downstream tube wall. The collection efficiency is significantly smaller without such curvature.

Headspace analysis of E-cigarette fluids using comprehensive two dimensional GC×GC-TOF-MS reveals the presence of volatile and toxic compounds

The analysis of electronic cigarrete (E-cigarette) fluids by high performance liquid chromatography or gas chromatography (GC) coupled to mass spectrometry (MS), GC hyphenated to flame-ionisation detection, or nuclear magnetic resonance spectroscopy poses many challenges due to the complex matrix and extremely high number of compounds present. In order to overcome these challenges, this study focused on the detection of the multiple complex compounds classes produced by the pyrolysis of E-cigarette liquids using comprehensive two dimensional gas chromatography (GCxGC) coupled to time of flight (TOF)-MS. Gas samples were prepared by heating E-liquids inside aluminium tins for 5 min. The tins were placed in a sand bath, which was temperature controlled at 200 °C. The samples were collected using thermal desorption tubes connected to volatile organic compound (VOC) sampling pump attached and subsequently analysed using GCxGC-TOF-MS. The greater peak resolution obtained when using GCxGC-TOF-MS allowed to distinguish many toxic compounds and VOCs that could not be detected by the other methods mentioned above. As a result, a comprehensive list of volatile compounds emitted from E-cigarette fluids when heated was established, which might allow a better understanding of potential health effects of vaping. Heating E-liquids to moderate temperature results in the emission of over 1000 volatile compounds of which over 150 are toxic. These compounds are either present in the liquid or can be formed during storage or heating leading to a more complex volatile profile of E-cigarette liquids than previously assumed. The application of GCxGC-TOF-MS allows the elucidation of this profile and therefore a better understanding of possible health implications.

Using experimental and computational approaches to probe an unusual carbon-carbon bond cleavage observed in the synthesis of benzimidazole N-oxides

Experimental and computational studies have been performed in order to investigate an unusual carbon-carbon bond cleavage that occurs in the preparation of certain benzimidazole N-oxides from anilines. The key factor determining the outcome of the reaction was found to be the substituents on the amine functionality of the aniline.

Sub-ohm vaping increases the levels of carbonyls, is cytotoxic, and alters gene expression in human bronchial epithelial cells exposed at the air-liquid interface

BACKGROUND

Exposure to electronic-cigarette (e-cig) aerosols induces potentially fatal e-cig or vaping-associated lung injury (EVALI). The cellular and molecular mechanisms underlying these effects, however, are unknown. We used an air-liquid interface (ALI) in vitro model to determine the influence of two design characteristics of third-generation tank-style e-cig devices-resistance and voltage-on (1) e-cig aerosol composition and (2) cellular toxicity.

METHODS

Human bronchial epithelial cells (H292) were exposed to either butter-flavored or cinnamon-flavored e-cig aerosols at the ALI in a Vitrocell exposure system connected to a third-generation e-cig device. Exposures were conducted following a standard vaping topography profile for 2 h per day, for 1 or 3 consecutive days. 24 h after ALI exposures cellular and molecular outcomes were assessed.

RESULTS

We found that butter-flavored e-cig aerosol produced under 'sub-ohm' conditions (< 0.5 Ω) contains high levels of carbonyls (7-15 μg/puff), including formaldehyde, acetaldehyde and acrolein. E-cig aerosol produced under regular vaping conditions (resistance > 1 Ω and voltage > 4.5 V), contains lower carbonyl levels (< 2 μg/puff). We also found that the levels of carbonyls produced in the cinnamon-flavored e-cig aerosols were much lower than that of the butter-flavored aerosols. H292 cells exposed to butter-flavored or cinnamon-flavored e-cig aerosol at the ALI under 'sub-ohm' conditions for 1 or 3 days displayed significant cytotoxicity, decreased tight junction integrity, increased reactive oxygen species production, and dysregulated gene expression related to biotransformation, inflammation and oxidative stress (OS). Additionally, the cinnamon-flavored e-cig aerosol induced pro-oxidant effects as evidenced by increases in 8-hydroxy-2-deoxyguanosine protein levels. Moreover, we confirmed the involvement of OS as a toxicity process for cinnamon-flavored e-cig aerosol by pre-treating the cells with N-acetyl cysteine (NAC), an antioxidant that prevented the cells from the OS-mediated damage induced by the e-cig aerosol.

CONCLUSION

The production of high levels of carbonyls may be flavor specific. Overall, inhaling e-cig aerosols produced under 'sub-ohm' conditions is detrimental to lung epithelial cells, potentially via mechanisms associated with OS. This information could help policymakers take the necessary steps to prevent the manufacturing of sub-ohm atomizers for e-cig devices.

Sub-ohm vaping increases the levels of carbonyls, is cytotoxic, and alters gene expression in human bronchial epithelial cells exposed at the air-liquid interface

Background

Exposure to electronic-cigarette (e-cig) aerosols induces potentially fatal e-cig or vaping-associated lung injury (EVALI). The cellular and molecular mechanisms underlying these effects, however, are unknown. We used an air–liquid interface (ALI) in vitro model to determine the influence of two design characteristics of third-generation tank-style e-cig devices—resistance and voltage—on (1) e-cig aerosol composition and (2) cellular toxicity.

Methods

Human bronchial epithelial cells (H292) were exposed to either butter-flavored or cinnamon-flavored e-cig aerosols at the ALI in a Vitrocell exposure system connected to a third-generation e-cig device. Exposures were conducted following a standard vaping topography profile for 2 h per day, for 1 or 3 consecutive days. 24 h after ALI exposures cellular and molecular outcomes were assessed.

Results

We found that butter-flavored e-cig aerosol produced under ‘sub-ohm’ conditions (< 0.5 Ω) contains high levels of carbonyls (7–15 μg/puff), including formaldehyde, acetaldehyde and acrolein. E-cig aerosol produced under regular vaping conditions (resistance > 1 Ω and voltage > 4.5 V), contains lower carbonyl levels (< 2 μg/puff). We also found that the levels of carbonyls produced in the cinnamon-flavored e-cig aerosols were much lower than that of the butter-flavored aerosols. H292 cells exposed to butter-flavored or cinnamon-flavored e-cig aerosol at the ALI under ‘sub-ohm’ conditions for 1 or 3 days displayed significant cytotoxicity, decreased tight junction integrity, increased reactive oxygen species production, and dysregulated gene expression related to biotransformation, inflammation and oxidative stress (OS). Additionally, the cinnamon-flavored e-cig aerosol induced pro-oxidant effects as evidenced by increases in 8-hydroxy-2-deoxyguanosine protein levels. Moreover, we confirmed the involvement of OS as a toxicity process for cinnamon-flavored e-cig aerosol by pre-treating the cells with N-acetyl cysteine (NAC), an antioxidant that prevented the cells from the OS-mediated damage induced by the e-cig aerosol.

Conclusion

The production of high levels of carbonyls may be flavor specific. Overall, inhaling e-cig aerosols produced under ‘sub-ohm’ conditions is detrimental to lung epithelial cells, potentially via mechanisms associated with OS. This information could help policymakers take the necessary steps to prevent the manufacturing of sub-ohm atomizers for e-cig devices.

Cell-specific toxicity of short-term JUUL aerosol exposure to human bronchial epithelial cells and murine macrophages exposed at the air-liquid interface

Backgroud

JUUL, an electronic nicotine delivery system (ENDS), which first appeared on the US market in 2015, controled more than 75% of the US ENDS sales in 2018. JUUL-type devices are currently the most commonly used form of ENDS among youth in the US. In contrast to free-base nicotine contained in cigarettes and other ENDS, JUUL contains high levels of nicotine salt (35 or 59 mg/mL), whose cellular and molecular effects on lung cells are largely unknown. In the present study, we evaluated the in vitro toxicity of JUUL crème brûlée-flavored aerosols on 2 types of human bronchial epithelial cell lines (BEAS-2B, H292) and a murine macrophage cell line (RAW 264.7).

Methods

Human lung epithelial cells and murine macrophages were exposed to JUUL crème brûlée-flavored aerosols at the air–liquid interface (ALI) for 1-h followed by a 24-h recovery period. Membrane integrity, cytotoxicity, extracellular release of nitrogen species and reactive oxygen species, cellular morphology and gene expression were assessed.

Results

Crème brûlée-flavored aerosol contained elevated concentrations of benzoic acid (86.9 μg/puff), a well-established respiratory irritant. In BEAS-2B cells, crème brûlée-flavored aerosol decreased cell viability (≥ 50%) and increased nitric oxide (NO) production (≥ 30%), as well as iNOS gene expression. Crème brûlée-flavored aerosol did not affect the viability of either H292 cells or RAW macrophages, but increased the production of reactive oxygen species (ROS) by ≥ 20% in both cell types. While crème brûlée-flavored aerosol did not alter NO levels in H292 cells, RAW macrophages exposed to crème brûlée-flavored aerosol displayed decreased NO (≥ 50%) and down-regulation of the iNOS gene, possibly due to increased ROS. Additionally, crème brûlée-flavored aerosol dysregulated the expression of several genes related to biotransformation, inflammation and airway remodeling, including CYP1A1, IL-6, and MMP12 in all 3 cell lines.

Conclusion

Our results indicate that crème brûlée-flavored aerosol causes cell-specific toxicity to lung cells. This study contributes to providing scientific evidence towards regulation of nicotine salt-based products.

Are In Silico Approaches Applicable As a First Step for the Prediction of e-Liquid Toxicity in e-Cigarettes?

Recent studies have raised concerns about e-cigarette liquid inhalation toxicity by reporting the presence of chemicals with European Union CLP toxicity classification. In this scenario, the regulatory context is still developing and is not yet up to date with vaping current reality. Due to the paucity of toxicological studies, robust data regarding which components in e-liquids exhibit potential toxicities, are still inconsistent. In this study we applied computational methods for estimating the toxicity of poorly studied chemicals as a useful tool for predicting the acute toxicity of chemicals contained in e-liquids. The purpose of this study was 3-fold: (a) to provide a lower tier assessment of the potential health concerns associated with e-liquid ingredients, (b) to prioritize e-liquid ingredients by calculating the e-tox index, and (c) to estimate acute toxicity of e-liquid mixtures. QSAR models were generated using QSARINS software to fill the acute toxicity data gap of 264 e-liquid ingredients. As a second step, the potential acute toxicity of e-liquids mixtures was evaluated. Our preliminary data suggest that a computational approach may serve as a roadmap to enable regulatory bodies to better regulate e-liquid composition and to contribute to consumer health protection.

A numerical investigation of the potential effects of e-cigarette smoking on local tissue dosimetry and the deterioration of indoor air quality

Electronic (e)-cigarette smoking is considered to be less harmful than traditional tobacco smoking because of the lack of a combustion process. However, e-cigarettes have the potential to release harmful chemicals depending on the constituents of the vapor. To date, there has been significant evidence on the adverse health effects of e-cigarette usage. However, what is less known are the impacts of the chemicals contained in exhaled air from an e-cigarette smoker on indoor air quality, the second-hand passive smoking of residents, and the toxicity of the exhaled air. In this study, we develop a comprehensive numerical model and computer-simulated person to investigate the potential effects of e-cigarette smoking on local tissue dosimetry and the deterioration of indoor air quality. We also conducted demonstrative numerical analyses for first-hand and second-hand e-cigarette smoking in an indoor environment. To investigate local tissue dosimetry, we used newly developed physiologically based pharmacokinetic/toxicokinetic models that reproduce inhalation exposure by way of the respiratory tract and dermal exposure through the human skin surface. These models were integrated into the computer-simulated person. Our numerical simulation results quantitatively demonstrated the potential impacts of e-cigarette smoking in enclosed spaces on indoor air quality.

Could E-cigarette vaping contribute to heart disease?

INTRODUCTION

E-cigarettes have become a controversial topic. While their benefits are questioned by the scientific community, a part of the medical profession is still supporting them as an effective harm reduction tool for smoking cessation. The impact of E-cigarettes on the cardiovascular system is still elusive.

AREAS COVERED

We assessed results from animal, pre(clinical), and epidemiological studies to critically evaluate and synthesize evidence relevant to the cardiovascular effects of E-cigarettes. Animal studies have demonstrated that E-cigarette vapor exposure can cause endothelial and cardiac dysfunction. However, there have also been reports on the less harmful effects of E-cigarette vapor exposure in comparison to classical tobacco cigarettes. Measurements of flow-mediated dilation in acute human exposure settings have mostly demonstrated that E-cigarettes cause vascular endothelial dysfunction. Epidemiological studies have shown that E-cigarette use is associated with an increased risk for cardiovascular disease, although switching from classical tobacco cigarettes to E-cigarettes can have beneficial cardiovascular effects. Misinterpretation of scientific data by activists on either side is another problem.

EXPERT OPINION

In conclusion, we need more and better (pre)clinical data comparing the health effects of E-cigarette vaping as compared with tobacco cigarette smoking, in order to counsel the legislation for better health policies.

The Impact of Device Settings, Use Patterns, and Flavorings on Carbonyl Emissions from Electronic Cigarettes

Health impacts of electronic cigarette (e-cigarette) vaping are associated with the harmful chemicals emitted from e-cigarettes such as carbonyls. However, the levels of various carbonyl compounds under real-world vaping conditions have been understudied. This study evaluated the levels of carbonyl compounds (e.g., formaldehyde, acetaldehyde, glyoxal, and diacetyl, etc.) under various device settings (i.e., power output), vaping topographies, and e-liquid compositions (i.e., base liquid, flavor types). The results showed that e-vapor carbonyl levels were the highest under higher power outputs. The propylene glycol (PG)-based e-liquids generated higher formaldehyde and acetaldehyde than vegetable glycerin (VG)-based e-liquids. In addition, fruit flavored e-liquids (i.e., strawberry and dragon fruit) generated higher formaldehyde emissions than mint/menthol and creamy/sweet flavored e-liquids. While single-top coils formed 3.5-fold more formaldehyde per puff than conventional cigarette smoking, bottom coils generated 10-10,000 times less formaldehyde per puff. In general, increases in puff volume and longer puff durations generated significantly higher amounts of formaldehyde. While e-cigarettes emitted much lower levels of carbonyl compounds compared to conventional cigarettes, the presence of several toxic carbonyl compounds in e-cigarette vapor may still pose potential health risks for users without smoking history, including youth. Therefore, the public health administrations need to consider the vaping conditions which generated higher carbonyls, such as higher power output with PG e-liquid, when developing e-cigarette product standards.

Formation of Diacetyl and Other α-Dicarbonyl Compounds during the Generation of E-Vapor Product Aerosols

Exposure to diacetyl (DA) has been linked to the respiratory condition bronchiolitis obliterans. Previous research has demonstrated that DA and other α-dicarbonyl compounds can be detected in both the e-liquids and aerosols of e-vapor products (EVPs). While some EVP manufacturers may add these compounds as flavor ingredients, the primary objective of this work was to determine the potential for the formation of α-dicarbonyl compounds during the generation of aerosols from EVPs where no DA or other α-dicarbonyl compounds are added to the e-liquid. A novel ultraperformance liquid chromatography-mass spectrometry-based analytical method for the determination of DA, acetyl propionyl, glyoxal, and methylglyoxal was developed and validated. Next, eight commercially available cig-a-like-type EVPs were evaluated for α-dicarbonyl formation. Increased levels of α-dicarbonyls were observed in the aerosols of all evaluated EVPs compared to their respective e-liquids. Mechanistic studies were conducted using a model microwave reaction system to identify key reaction precursors for DA generated from propylene glycol (PG) and carbon-13-labeled glycerin (GLY). These studies, along with the corresponding retrosynthetic analysis, resulted in the proposed formation pathway where hydroxyacetone is generated from PG and/or GLY. Hydroxyacetone then participates in an aldol condensation with formaldehyde where formaldehyde can also be generated from PG and/or GLY; the resultant product then dehydrates to form DA. This proposed pathway was further investigated through in situ synthetic organic experiments within the model microwave reaction system. This work establishes that DA is formed in the aerosol generation process of the EVPs tested though at levels below toxicological concern.

Method Validation Approaches for Analysis of Constituents in ENDS

OBJECTIVE

We assessed how many peer-reviewed publications reporting chemical quantities and/or yields from electronic nicotine delivery systems (ENDS) have included adequate method validation characteristics in the publication for appropriate interpretation of data quality for informing tobacco regulatory science.

METHODS

We searched 5 databases (Web of Knowledge, PubMed, SciFinder, Embase, EBSCOhost) for ENDS publications between January 2007 and September 2018. Of the 283 publications screened, 173 publications were relevant for analysis. We identified the publications that report a certain degree of control in data quality, ie, the publications that report marginally validated methods (MVMs). MVMs refer to the methods that: (1) report 3 or more International Conference on Harmonisation (ICH) method validation characteristics, (2) state the method was validated, (3) cite their own previous publication(s) that report MVMs, or (4) use a method within the accreditation scope of an accredited laboratory.

RESULTS

Overall, 97 publications (56%) report MVMs in their studies. This percentage also reflects the publication distribution for the majority of the 28 chemicals measured by MVMs.

CONCLUSIONS

This study highlights the need for reporting sufficient validation characteristics following appropriate guidance to ensure the accuracy and reliability of the published analytical data for proper data interpretations that may support policy.

Development of a standardized new cigarette smoke generating (SNCSG) system for the assessment of chemicals in the smoke of new cigarette types (heat-not-burn (HNB) tobacco and electronic cigarettes (E-Cigs))

To systematically regulate new types of cigarettes for which their safety has yet to be verified, such as heat-not-burn (HNB) products and electronic cigarettes (E-Cigs), the identification of chemicals in the new cigarette smoke is necessary. However, this is challenging due to the large number of new cigarette types and their different vaporization approaches. To address this issue, we herein report the development of a standardized new cigarette smoke generating (SNCSG) system based on heating-temperature control, which is able to generate smoke for all types of new cigarettes. Validation of the developed system was also carried out through analysis of the carbonyl compounds (e.g., formaldehyde and acetaldehyde) in the new cigarette smoke of HNB products and E-Cigs generated by the SNCSG system under different heating temperatures. The analytical results were used to validate the SNCSG system by comparison with those of previous studies. In all new cigarette smoke samples, the formaldehyde and acetaldehyde concentrations increased dramatically upon increasing the heating temperatures, especially over the reference heating range of each HNB device (mean concentration (μg/cigarette, n = 5 (HNB and E-Cig samples)): formaldehyde = 0.373-5.841 (250-320 °C), and acetaldehyde = 0.088-27.60 (250-320 °C). In the case of the HNB samples, the concentration differences determined by the heating temperatures of the tobacco stick were statistically significant, with p-values (ANOVA) of 1.85E-10 (formaldehyde) and 1.73E-08 (acetaldehyde). In the majority of smoke samples, acrolein and propionaldehyde were detected under relatively high heating temperature conditions (>250 °C) at 0.50 ± 1.76 μg/(cigarette or 10 μL), while acetone was detected under low heating temperature conditions (<250 °C) at 0.09 ± 0.17 μg/(cigarette or 10 μL). These results indicate that the developed SNCSG system could be suitable for application in the regulation of new types of cigarettes, regardless of the cigarette type and heating approach.

Carbonyls and Carbon Monoxide Emissions from Electronic Cigarettes Affected by Device Type and Use Patterns

Dangerous levels of harmful chemicals in electronic cigarette (e-cigarette) aerosols were reported by several studies, but variability in e-cigarette design and use patterns, and a rapid development of new devices, such as JUUL, hamper efforts to develop standardized testing protocols and understand health risks associated with e-cigarette use. In this study, we investigated the relative importance of e-cigarette design, power output, liquid composition, puff topography on e-cigarette emissions of carbonyl compounds, carbon monoxide (CO), and nicotine. Four popular e-cigarette devices representing the most common e-cigarette types (e.g., cig-a-like, top-coil, 'mod', and 'pod') were tested. Under the tested vaping conditions, a top-coil device generated the highest amounts of formaldehyde and CO. A 'pod' type device (i.e., JUUL) emitted the highest amounts of nicotine, while generating the lowest levels of carbonyl and CO as compared to other tested e-cigarettes. Emissions increased nearly linearly with puff duration, while puff flow had a relatively small effect. Flavored e-liquids generated more carbonyls and CO than unflavored liquids. Carbonyl concentrations and CO in e-cigarette aerosols were found to be well correlated. While e-cigarettes emitted generally less CO and carbonyls than conventional cigarettes, daily carbonyl exposures from e-cigarette use could still exceed acute exposure limits, with the top-coil device potentially posing more harm than conventional cigarettes.

Effects of Electronic Cigarettes on Indoor Air Quality and Health

With the rapid increase in electronic cigarette (e-cig) users worldwide, secondhand exposure to e-cig aerosols has become a serious public health concern. We summarize the evidence on the effects of e-cigs on indoor air quality, chemical compositions of mainstream and secondhand e-cig aerosols, and associated respiratory and cardiovascular effects. The use of e-cigs in indoor environments leads to high levels of fine and ultrafine particles similar to tobacco cigarettes (t-cigs). Concentrations of chemical compounds in e-cig aerosols are generally lower than those in t-cig smoke, but a substantial amount of vaporized propylene glycol, vegetable glycerin, nicotine, and toxic substances, such as aldehydes and heavy metals, has been reported. Exposures to mainstream e-cig aerosols have biologic effects but only limited evidence shows adverse respiratory and cardiovascular effects in humans. Long-term studies are needed to better understand the dosimetry and health effects of exposures to secondhand e-cig aerosols.

Effects of Electronic Cigarettes on Indoor Air Quality and Health

With the rapid increase in electronic cigarette (e-cig) users worldwide, secondhand exposure to e-cig aerosols has become a serious public health concern. We summarize the evidence on the effects of e-cigs on indoor air quality, chemical compositions of mainstream and secondhand e-cig aerosols, and associated respiratory and cardiovascular effects. The use of e-cigs in indoor environments leads to high levels of fine and ultrafine particles similar to tobacco cigarettes (t-cigs). Concentrations of chemical compounds in e-cig aerosols are generally lower than those in t-cig smoke, but a substantial amount of vaporized propylene glycol, vegetable glycerin, nicotine, and toxic substances, such as aldehydes and heavy metals, has been reported. Exposures to mainstream e-cig aerosols have biologic effects but only limited evidence shows adverse respiratory and cardiovascular effects in humans. Long-term studies are needed to better understand the dosimetry and health effects of exposures to secondhand e-cig aerosols.

Analytical methods for determination of carbonyl compounds and nicotine in electronic No-Smoking aid refill solutions

The present investigation aimed to develop analytical methods to determine carbonyl compounds and nicotine and to assess the carbonyl compounds and nicotine concentrations in commercial refill solutions for electronic no-smoking aids (ENSAs). The analytical methods for carbonyl compounds and nicotine in refill solutions for ENSAs were developed and analyzed from 30 popular branded products by gas chromatography and liquid chromatography. They were then validated in terms of linearity of the calibration curve, limit of detection (LOD), limit of quantification (LOQ), accuracy (%), and precision (%). Further, the existence of carbonyl compounds and nicotine in the refill solutions for ENSAs was also evaluated. None of the samples contained nicotine, but carbonyl compounds were sensed in a concentration range from 0.9 to 11.65 μg/mL. Manufacturers of ENSA refill solutions have advertised no-smoking aids as less harmful than tobacco cigarettes and as free from harmful substances. However, carbonyl compounds were detected in all 30 samples. The investigation of ENSA refill solutions needs to be broadened to gain a better accepting of the existence of harmful materials in ENSA refill solutions and prevent unsuspected ill-health effects.

A Strategy for Efficiently Collecting Aerosol Condensate Using Silica Fibers: Application to Carbonyl Emissions from E-Cigarettes

Analyzing harmful constituents in e-cigarette aerosols typically involves adopting a methodology used for analyzing tobacco smoke. Cambridge filter pads (CFP) are the basis of numerous protocols for analyzing the various classes of compounds representing 93 harmful and potentially harmful constituents identified in tobacco smoke by the FDA. This paper describes a simplified method for trapping the low volatility components of e-cigarette aerosols using a single trapping procedure followed by physical extraction. The trap is a plug of amorphous silica fibers (0.75 g of 4 μm diameter) within a 10 mL syringe inserted between the e-cigarette mouthpiece and the pump of the vaping machine. The method is evaluated for emissions from three generations of e-cigarette device (Kangertech CE4, EVOD, and Subox Mini-C). On average, the silica wool traps about 94% of the vaporized liquid mass in the three devices and higher levels of condensate is retained before reaching saturation compared with CFP. The condensate is then physically extracted from the silica wool plug using a centrifuge. Condensate is then available for use directly in multiple analytical procedures or toxicological experiments. The method is tested by comparison with published analyses of carbonyls, among the most potent toxicants and carcinogens in e-cigarette emissions. Ranges for HPLC-DAD analyses of carbonyl-DNPH derivatives in a laboratory formulation of e-liquid are formaldehyde (0.182 ± 0.023 to 9.896 ± 0.709 μg puff-1), acetaldehyde (0.059 ± 0.005 to 0.791 ± 0.073 μg puff-1), and propionaldehyde (0.008 ± 0.0001 to 0.033 ± 0.023 μg puff-1); other carbonyls are identified and quantified. Carbonyl concentrations are also consistent with published experiments showing marked increases with variable power settings (10W to 50W). Compared with CFPs, e-cigarette aerosol collection by silica wool requires only one vaping session for multiple analyte groups, traps more condensate per puff, and collects more condensate before saturation.

[Exposure of vapers to formaldehyde and acrolein: A systematic review]

Although recognized as less dangerous than conventional cigarettes, the toxicity of the electronic cigarette vapor's toxicity remains to be fully assessed. This review explores vapers' exposition to formaldehyde and acrolein.

METHOD

Systematic PubMed search for reports regarding formaldehyde or acrolein or their metabolites in electronic cigarette vapor, in vapers, or in ambient air.

RESULTS

Fifty-two publications were selected. Found in almost all studies on vaper, formaldehyde is 8 times out of 11 - and acrolein constantly - in lower amounts than those found in conventional cigarettes. Acrolein's metabolite is found in all studies in vapers. The concentrations of formaldehyde and/or acrolein generated during vapor production may be affected by the characteristics of the E-liquid, voltage, vaping topography, and by the flavor additives.

CONCLUSION

In the current state of knowledge, we must continue to support and help smokers to quit smoking, and for those who are engaged in a harm reduction approach, to minimize the duration of their electronic cigarette use.

The toxic potential of a fourth-generation E-cigarette on human lung cell lines and tissue explants

The use of electronic cigarettes (E-cigs) is rapidly increasing. The latest generation of E-cigs is highly customizable, allowing for high heating coil temperatures. The aim of this study was to assess the toxic potential of a fourth-generation E-cig. Aerosols generated from E-liquid with (24 mg/mL) and without nicotine, using a fourth-generation E-cig, were chemically analysed and compared with cigarette smoke (K3R4F). Human lung epithelial cell lines and distal lung tissue explants were exposed to E-cig vapour extract (EVE) and cigarette smoke extract for 24 hours and assessed for viability, inflammation, oxidative stress and genotoxicity. E-cig aerosols contained measurable levels of volatile organic compounds, aldehydes and polycyclic aromatic hydrocarbons, in general, to a much lesser extent than cigarette smoke. Higher levels of certain carbonyls, e.g. formaldehyde, were detected in the E-cig aerosols. EVEs decreased cell viability of BEAS-2B cells, whereas little effect was seen in A549 cells and distal lung tissue. The nicotine-containing EVE caused a greater decrease in cell viability and significant increase in DNA damage than the nicotine-free EVE. Increased cytotoxicity, reactive oxygen species production and genotoxicity were seen with cells and tissue exposed to cigarette smoke extract compared with EVEs. Although E-cig aerosols were less toxic than cigarette smoke, it was not benign. Moreover, the EVE containing nicotine was more toxic than the nicotine-free EVE. More research is needed on the short- and long-term health effects of vaping and the usage of newly emerging E-cig devices to evaluate better the potential negative effects of E-cigs on human health.

Simultaneous Determination of Four Aldehydes in Gas Phase of Mainstream Smoke by Headspace Gas Chromatography-Mass Spectrometry

A method for simultaneous determination of acetaldehyde, propionaldehyde, acrolein, and crotonaldehyde in gas phase of cigarette mainstream smoke by headspace gas chromatography-mass spectrometry was developed and validated. Gas phase components of mainstream cigarette smoke were extracted with methanol, and then the samples were separated on a DB 624 (60 m, 0.32 mm x 1.8 mm) column, analyzed with headspace gas chromatography-mass spectrometry, and quantified by isotope internal standard. The linearities of acetaldehyde, propionaldehyde, acrolein, and crotonaldehyde were good (R²>0.992). The recoveries of acetaldehyde, propionaldehyde, acrolein, and crotonaldehyde were between 78.5% and 115%. The relative standard deviations were less than 10%. The limits of detection and limits of quantitation were 0.014 μg/cigarette ~0.12 μg/cigarette and 0.045 μg/cigarette ~0.38 μg/cigarette, respectively. The method had advantage of high sensitivity, it did not require derivatization of 2,4-dinitrophenylhydrazine and avoided a large number of adverse reactions during the process of derivation to improve the accuracy of result, and it was suitable for quantitative analysis of four aldehydes in gas phase of cigarette mainstream smoke.

A review of the impacts of tobacco heating system on indoor air quality versus conventional pollution sources

With the introduction of novel and potentially less polluting nicotine containing products to the market, the impacts of their usage to indoor air quality as opposed to conventional pollution sources must be reviewed and considered. This review study aimed to comparatively analyse changes in indoor air quality as the consequence of tobacco heating system (THS) generated pollution against general indoor air quality in various micro-environments, especially with combustion-based pollution sources present. Indoor concentrations of formaldehyde, acetaldehyde, benzene, toluene, nicotine and PM_2.5 were reviewed and compared; concentrations of other harmful and potentially harmful substances (HPHCs) were discussed. Generally, the usage of THS has been associated with lower or comparable indoor air pollutant concentrations compared against other conventional indoor sources or environments, in most cases distinguishable above background, thus potentially being associated with health effects at prolonged exposures as any other artificial air pollution source. In the controlled environment the use of THS (as well as an electronic cigarette) resulted in the lowest concentrations of formaldehyde, benzene, toluene, PM_2.5, among majority researched pollution sources (conventional cigarettes, waterpipe, incense, mosquito coils). The exposure to significantly higher pollution levels of benzene, toluene, and formaldehyde occurred in public environments, especially transport micro-environments. Such low levels of conventionally-assessed indoor pollutants resulting from the use of new nicotine containing products raise challenges for epidemiological studies of second-hand exposure to THS aerosol in real-life environments.

Surface Chemistry of Electronic Cigarette Electrical Heating Coils: Effects of Metal Type on Propylene Glycol Thermal Decomposition

INTRODUCTION

Carbonyls, a class of compounds strongly linked to pulmonary disease in smokers, are probably the most reported non-nicotine toxicants found aerosols. Reported emissions vary from negligible quantities to those far exceeding combustible cigarettes. Observations of high emissions are commonly attributed to "dry puffing", whereby the ECIG heating filament runs dry of liquid and reaches temperatures that induce thermal degradation of the ECIG vapor components at the filament's metal surface. Using a pyrolysis flow reactor, in this study we examined the potential role of surface chemistry in the formation of carbonyl compounds in ECIGs, and whether the different commercially available filament materials could potentially impact their toxicant emissions through catalysis. This information could inform nascent efforts to regulate the design of ECIGs for public health ends.

METHODS

Nitrogen or air saturated with propylene glycol vapor was drawn through a temperature and residence time controlled tubular quartz pyrolysis flow reactor in which nichrome, Kanthal, or stainless steel ECIG heating filament wires were inserted. A control condition with no inserted wire was also included. Concentrations of carbonyl products at the reactor outlet were measured as a function of temperature, heating filament wire material, and carrier gas composition (N2 vs air). Carbonyls were sampled using DNPH cartridges and analyzed by HPLC.

RESULTS

ECIG heating filament wires were found to have a strong catalytic effect. Carbonyl formation initiated at temperatures lower than 250°C in the presence of the metallic wires, compared to 460°C without them. Carbonyl formation was found to be a function of the material of construction, and whether the wire was new or aged. New nichrome wires were the least reactive, but when aged they exhibited the highest reactivity. Carbonyls were formed via dehydration or oxidation reactions of PG.

CONCLUSIONS

Carbonyl formation chemistry is catalyzed by commonly used ECIG heating filament materials, at temperatures that are well below those expected during "dry puffing". The variability in the distribution and yield of carbonyl compounds across ECIG filament materials suggests that this heretofore unaccounted variable may partially explain the wide ranges reported in the literature to date. More importantly, it suggests that ECIG construction materials may be an important variable for regulations designed to protect public health.

Generation of Electronic Cigarette Aerosol by a Third-Generation Machine-Vaping Device: Application to Toxicological Studies

Electronic-cigarette (e-cig) devices use heat to produce an inhalable aerosol from a liquid (e-liquid) composed mainly of humectants, nicotine, and flavoring chemicals. The aerosol produced includes fine and ultrafine particles, and potentially nicotine and aldehydes, which can be harmful to human health. E-cig users inhale these aerosols and, with the third-generation of e-cig devices, control design features (resistance and voltage) in addition to the choice of e-liquids, and the puffing profile. These are key factors that can significantly impact the toxicity of the inhaled aerosols. E-cig research, however, is challenging and complex mostly due to the absence of standardized assessments and to the numerous varieties of e-cig models and brands, as well as e-liquid flavors and solvents that are available on the market. These considerations highlight the urgent need to harmonize e-cig research protocols, starting with e-cig aerosol generation and characterization techniques. The current study focuses on this challenge by describing a detailed step-by-step e-cig aerosol generation technique with specific experimental parameters that are thought to be realistic and representative of real-life exposure scenarios. The methodology is divided into four sections: preparation, exposure, post-exposure analysis, plus cleaning and maintenance of the device. Representative results from using two types of e-liquid and various voltages are presented in terms of mass concentration, particle size distribution, chemical composition and cotinine levels in mice. These data demonstrate the versatility of the e-cig exposure system used, aside from its value for toxicological studies, as it allows for a broad range of computer-controlled exposure scenarios, including automated representative vaping topography profiles.

New approach for e-cigarette aerosol collection by an original automatic aerosol generator utilizing melt-blown non-woven fabric

Currently, there is lack of standardized conditions for the collection and analysis of e-cigarette (EC) aerosol. Considering the urgent need for the development of these guidelines, a procedure for EC aerosol analysis was developed. A novel automatic e-cigarette aerosol generator was designed. For the first time, melt-blown non-woven fabric was applied for the effective uptake of compounds released from vaporized e-liquid. The extraction procedure was optimized in terms of type of extraction solvent, amount of sorbent and solvent volume. For optimization, a model e-liquid containing flavour additives belonging to various chemicals group with various chemical properties was investigated. The aerosol trapping efficiency was satisfactory and was equal to 92 ± 7%. Final determination was performed by GC-MS/MS. Quantitation was based on the mass change tracking approach (MCT), which assumes the monitoring of e-liquid mass changes before and after vaping. The combination of non-woven fabric and sampling approach (MCT) was proven to be effective in acquisition of reliable data. Thus, the concentrations in aerosol and emission factors were calculated for aerosols collected during the vaping of both model e-liquids and real samples. Validation was performed by evaluating key analytical parameters, such as linearity, accuracy, precision, limit of detection (LOD) and quantitation (LOQ). For all investigated compounds, recoveries from 70% to 118% together with precision and reproducibility below 12% were achieved. The applicability of the described approach was examined by analysing EC refill solutions commercially available on the Polish market.

Short-Term E-Cigarette Exposure Increases the Risk of Thrombogenesis and Enhances Platelet Function in Mice

Background

Cardiovascular disease is the main cause of death in the United States, with smoking being the primary preventable cause of premature death, and thrombosis being the main mechanism of cardiovascular mortality in smokers. Due to the perception that electronic/e‐cigarettes are “safer/less harmful” than conventional cigarettes, their usage—among a variety of ages—has increased tremendously during the past decade. Notably, there are limited studies regarding the negative effects of e‐cigarettes on the cardiovascular system, which is also the subject of significant debate.

Methods and Results

We employed a passive e‐Vape^TM vapor inhalation system and developed an in vivo whole‐body e‐cigarette mouse exposure protocol that mimics real‐life human exposure scenarios/conditions and investigated the effects of e‐cigarettes and clean air on platelet function and thrombogenesis. Our results show that platelets from e‐cigarette–exposed mice are hyperactive, with enhanced aggregation, dense and α granule secretion, activation of the αIIbβ3 integrin, phosphatidylserine expression, and Akt and ERK activation, when compared with clean air–exposed platelets. E‐cigarette–exposed platelets were also found to be resistant to inhibition by prostacyclin, relative to clean air. Furthermore, the e‐cigarette–exposed mice exhibited a shortened thrombosis occlusion and bleeding times.

Conclusions

Taken together, our data demonstrate for the first time that e‐cigarettes alter physiological hemostasis and increase the risk of thrombogenic events. This is attributable, at least in part, to the hyperactive state of platelets. Thus, the negative health consequences of e‐cigarette exposure should not be underestimated and warrant further investigation.